pages - Weschler Instruments
Fluke Handheld Oscilloscopes
The 125 offers additional capabilities for testing industrial machinery:
The ScopeMeter 190 Series of high performance oscilloscopes have bandwidth of 60,
100, and 200 MHz and sample rates up to
2.5 GS/s. The high resolution color display
has a fast update rate and digital persistence
mode – making the analysis of complex and
dynamic signals that much easier.
124
Choose the 190 Series for tough troubleshooting problems, like intermittent failures, impulses and signal fluctuations in high speed or
sensitive electronic or electromechanical systems. They include automatic measurements,
cursors, FFT analysis, paperless recording
functions and a DMM input.
For industrial electronic or electromechanical
applications, the 120 Series Industrial
ScopeMeters offer bandwidth to 40MHz, a
dual DMM and paperless recording.
190
ScopeMeter 190 Series II
Model
190-202
Bandwidth
Max. real time sample rate
Display
Persistence
200 MHz
2.5 GS/s
Max. record length
TEST
EQUIPMENT
Number of inputs
Number of digitizers
Independently floating
isolated inputs
Input sensitivity
Glitch capture
Waveform zoom
Timebase range in
Scope mode
Trigger types
190-102
• Power & harmonic measurements for single
phase and balanced 3-phase systems.
• RPM and Hz reading for motors & engines.
• Vac PWM for motor drive outputs.
• 0.01 ohm resolution for motor & transformer windings.
• a Bus Health function for troubleshoting
industrial data networks.
For fast measurement answers and quick display of waveforms all ScopeMeters include
Connect-and-View triggering. This feature recognizes signal patterns and automatically sets
the oscilloscope for a stable
reliable display of even the most complex
waveforms. Move from test point to test point
and the ScopeMeter will continuously lock
onto just about any waveform.
NEW
Industrial ScopeMeters
190-062
Fluke 123
100 MHz
60 MHz
1 GS/s
0.5 GS/s
15.3 cm Full Color LCD
Digital Persistence giving analog
oscilloscope-like waveform decay
10,000 points per input (Scope mode)
30,000 points per input (ScopeRecord mode)
2 plus external/DMM input
2
Up to 1000 V between inputs, references and ground
20 MHz
25 MS/s
2 mV/div. … 100 V/div.
8 ns
100x
2 ns/div. to 2 min/div.
Connect-and-View®, Free Run, Single Shot, Edge, Delay, Dual Slope,
Video, Video line, Selectable pulse width, N-cycle and External
7 cursors , 30 automatic measurements
–––
Start on Trigger / Stop on Trigger
Fluke 124
Fluke 125
40 MHz
40 MHz
25 MS/s
25 MS/s
10.2 cm Monochrome LCD
–––
512 min/max pairs per input
2
2
600 V RMS max input or
any terminal to ground
5 mV/div. … 500V/Div
40 ns
--10 ns/div. to
20 ns/div. to
1 min/div.
1 min/div.
Connect-and-View®, Free Run, Single
Shot, Edge, Video, External
26 automatic measurements
--W, VA, VAR. PF
---
Scope Measurements
Power Measurements
Scope-Record Trigger
modes
Capture last 100 screens
Automatic with Replay capability
--Dual input TrendPlot
Yes with Cursors and Zoom
Yes
Yes
Memory for screens
30 screens and set-ups
10
20
Memory for recordings
10
1
External Memory
Isolated USB host port for data storage to USB memory
--True RMS multimeter
5000 counts, Volts, Amps, Ohms, Continuity, Diode, Temp
Safety certified
1000 V CAT II / 600 V CAT III
600 V CAT III
Battery power
4 hr Li-Ion battery included
7 hr NiMH
Line power
Adapter/battery charger included
Size (cm)/Weight
27.0 x 19.0 x 7.0 / 2.2 kg
23.2 x 11.5 x 5.0 / 1.2 kg
Temperature
0-50°C operating (0-40°C with batteries)
0-50°C operating
PC and Printer interface
Isolated USB (cable included)
Using optional Optically Isolated adapter/cable
Warranty
3 years (1 year on accessories)
Add /S to model number to include Flukeview software, isolated USB cable & hard carrying case
139
Fluke High Performance Digital Multimeters
NEW
The Fluke 287 True-rms Electronics Logging Multimeter with TrendCapture quickly documents performance and graphically displays results.
• Large 50,000 count, 1/4 VGA display with white backlight. Displays multiple sets of measurements simultaneously
• Logging function with expanded memory stores up to
15,000 recorded events
• TrendCapture graphically displays logged data session
• Zoom up to 14X to view & analyze TrendCapture data
• Selectable ac filter helps display rapidly changing or
noisy signals
• Adjustable recording & auto hold thresholds, specify a
percentage change in the readings that begins a new
event
• On board help screens for measurement functions
287
L
Includes manual, 6 AA batteries, TL71 silicone test leads,
probe holder, two AC72
alligator clips
•
•
•
•
•
•
•
Multiple logging sessions without download
0.025 % basic dc accuracy
True-rms ac and ac+dc
100 kHz ac bandwidth
Real-time clock time-stamps saved readings
Peak capture to record transients as fast as 250 µs
Relative mode to remove test lead resistance from low
ohms or capacitance measurements
• Optional FlukeView software to document, store and
analyze measurements
• CATIII – 1000V & CAT IV – 600V ratings
• Limited lifetime warranty
SPECIFICATIONS
Function
Range & resolution
VDC, VAC
ADC, AAC
Resistance
Capacitance
Frequency
Temperature
50.000 mV, 500.00 mV, 5000.0 mV, 5.0000 V, 50.000 V, 500.00 V, 1000.0 V
500.00 µA, 5.000 µA, 50.000 mA, 400.00 mA, 5.0000 A, 10.000 A*
500.00Ω - 500.0 MΩ (7 ranges)
1.100 nF - 100.0 mF (9 ranges)
99.999 Hz - 999.99 kHz (5 ranges)
-200 to 1350°C, -328 to 2462°F
Battery life:
Environment:
Basic Accuracy
100 hours minimum, 200 hours in logging mode
-20°C to 55°C, <90% RH up to 37°C
0.025% (0.4% AC)
0.15% (0.7% AC)
0.05%
1.0%
0.005%
1.0%
*10A continuous, 20A for up to 30 seconds.
Size: 222x102x60 mm (8.75 x 4.03 x2.38")
Fluke 289 adds 50Ω range for measuring contacts & motor windings
plus a LowZ voltage function for eliminating ghost voltages.
The Fluke 87V has improved measurement functions & troubleshooting features, to solve problems on motor drives, inplant automation, power distribution and electro-mechanical equipment.
• Selectable filters for accurate
measurements on adjustable
speed drives
• Built-in thermometer
•
•
•
•
Capacitance to 10,000µF
30% larger display
2 level backlight
4x faster (250µS) peak capture
• CATIII-1000V & CATIV-600V rating
• Lifetime warranty
SPECIFICATIONS
L
Includes: TL75 Test Leads,
AC72 Alligator Clips,
holster, 9V battery,
temperature probe
Range & resolution
600.0 mV, 6.000 V, 60.00 V, 600.0 V, 1000 V
600.0 mV, 6.000 V, 60.00 V, 600.0 V, 1000 V
600.0 µA, 6000 µA, 60.00 mA, 600.O mA, 6.000 A, 10.00 A
600.0 µA, 6000 µA, 60.00 mA, 600.O mA, 6.000 A, 10.00 A
-200 to 1090 °C (-328 to 1994 °F)
-40 to 260 °C (-40 to 500 °F)
600.0 Ω, 6.000 kΩ, 60.00 kΩ, 600.0 kΩ, 6.000 MΩ, 50.00 MΩ
10.00 nF, 100.0 nF, 1.000 µF, 10.00 µF, 100.0 µF, 9,999 µF
199.99 Hz, 1.9999 kHz, 19.999 kHz, 199.99 kHz
Battery Life: 100 hours typical with headlight off.
Size: (LxWxD): 201mm x 98mm x 52mm (7.9in x 3.6in x 2in)
Fluke 87V/E2 Industrial Electrician Combo Kit
Includes special accessories to increase productivity.
• 1.5m heat resistance silicone test • Magnetic hanger to position and
hold meter to steel surfaces
leads
• Removable test probes with 4mm • Temperature probe
of exposed metal for use on
• Packaged in a durable carrying
industrial circuits
case
• Plunger style alligator clips
Basic Accuracy (87V)
0.05 %
0.7 % (True-rms)
0.2 %
1.0 % (True-rms)
1.0 %
2.2 °C or 2 %
0.2 %
1.0 %
0.005 %
ORDERING INFORMATION
Fluke-87-5
Industrial True-rms Multimeter with Temperature
Fluke-87-5/E2 Industrial Electrician Combo Kit
Fluke-287
True-rms Electronics Logging Multimeter
Fluke-289
True-rms Electronics Logging Multimeter
FVF-SC2
FlukeView® forms software with cable
80BK
Integrated DMM temperature probe
i410
AC/DC current clamp
TLK287
Electronic test lead set
TPAK
Magnetic hanging kit
C280
Soft case
140
TEST
EQUIPMENT
87V
Function
DC Volts
AC Volts
DC Current
AC Current
Temperature (excl. probe)
80BK Temperature Probe
Resistance
Capacitance
Frequency
Fluke Compact Digital Multimeters
These little meters pack more features than some DMMs twice their size:
M
Fluke 117
• True-rms ac voltage and current
measurement for accurate readings
on all waveforms
• 6000-count display provides
improved resolution
• Min/Max/Average feature captures
signal fluctuations
• Frequency, capacitance and
diode test capabilities (except 114)
• White LED backlight for excellent visibility
• Fast continuity test detects intermittent
connections
• IEC CAT III 600V safety rating
• Auto-Volt automatic ac/dc voltage selection
SPECIFICATIONS
Every Fluke 110
Series meter comes
with a protective holster, TL75 test leads,
9V battery (installed) and manual.
ORDERING INFO
Fluke-114
Fluke-115
Fluke-116
Fluke-117
Electrical Multimeter
Multimeter
HVAC Multimeter w/ temp. probe
Electrician’s Multimeter
Meter hanging kit with magnet
Alligator clips
Carrying case
Range & resolution
Best accuracy
VDC
VAC1
ADC (Models 115 & 117 only)
AAC (Models 115 & 117 only)
Resistance
600.0 mV, 6.000 V, 60.00 V, 600.0 V
600.0 mV, 6.000 V, 60.00 V, 600.0 V
6.000 A, 10.00 A2
6.000 A, 10.00 A2
600.0 Ω, 6.000 kΩ, 60.00 kΩ,
600.0 kΩ, 6.000 MΩ, 40.00 MΩ
1000 nF, 10.00 µF, 100.0 µF, 9999 µF
99.99 Hz, 999.9 Hz, 9.999 Hz, 50.00 kHz
±0.5 % of rdg + 2 d
±1.0 % of rdg + 3 d
±1.0 % of rdg + 3 d
±1.5 % of rdg + 3 d
Capacitance (except Model 114)
Frequency3 (except Model 114)
RECOMMENDED ACCESSORIES
TPAK
AC220
C50
Function
1
Specified from 1% of range to 100% of range; CF < 3 up to 4000
counts, 1.5 at full scale.
2
10 A continuous, 20 A for up to 30 seconds, 45-500 Hz.
3
Frequency is ac coupled 5 Hz to 50 kHz for ac volts. Frequency is dc
coupled 445 Hz to 5 kHz for ac current.
AC volts is ac-coupled. Auto-V, LoZ and ac mV are dc-coupled.
Battery life: 400 hours typical for alkaline.
33 segment Bargraph display updates 32x/sec.
±0.9 % of rdg + 1 d
±1.9 % of rdg + 2 d
±0.1 % of rdg + 2 d
Additional Model 116 features:
• °F/°C temperature function
for HVAC troubleshooting
• 600µA ac & dc ranges for
testing flame sensors
Fluke Digital Multimeters
TEST
EQUIPMENT
M
Fluke 179
The 170 series replaces the popular 70 Series.
The 175, 177 and 179 are designed tough to
withstand the harshest work environments.
Accuracy rivals most bench meters.
Every Fluke 170 Series meter comes with TL75
test leads, 9V battery (installed) and manual.
The Fluke 179 also includes an 80BK
Temperature Probe.
•
•
•
•
•
•
•
• The 179 measures temperature in °C and °F
• 177 and 179 have a backlight to illuminate the
screen in dark workspaces
• IEC 1010 CAT IV 600V, CAT III 1000V
safety ratings
• Drop protected to 1 meter
• Overmolded case features integrated probe
holders
• Compatible with ToolPak™ meter hanging kit
Lifetime warranty
6000 count display
0.09% basic dc accuracy (177 & 179)
True-rms ac voltage and current measurement
Min/Max/Average records irregular activity
Auto and Manual hold
Frequency, capacitance and resistance
capabilities
ORDERING INFO
SPECIFICATIONS
Function
Range & Resolution
VDC
600.0 mV, 6.000 V, 60.00 V, 600.0 V, 1000V
VAC1
ADC
AAC
Resistance
Capacitance
Frequency3
Temperature
(Model 179)
600.0 mV, 6.000 V, 60.00 V, 600.0 V, 1000V
60.00 mA, 400.0 mA, 6.000 A, 10.00 A2
60.00 mA, 400.0 mA, 6.000 A, 10.00 A2
600.0 Ω, 6.000 kΩ, 60.00 kΩ, 600.0 kΩ, 6.000 MΩ, 50.00 MΩ
1000 nF, 10.00 µF, 100.0 µF, 9999 µF
99.99 Hz, 999.9 Hz, 9.999 Hz, 99.99 kHz
Best accuracy
±0.09 % (177 & 179)
±0.15 % (175)
±1.0 % of reading
±1.0 % of reading
±1.5 % of reading
±0.9 % of reading
±1.2 % of reading
±0.1 % of reading
-40 °C to +400 °C, -40 °F to +752 °F
All AC voltage and AC current ranges are specified from 5% of range to 100% of range.
2
10 A continuous, 20 A for up to 30 seconds.
3
Voltage Frequency is specified from 2 Hz to 100 kHz. Current Frequency is specified from 2 Hz to 30 kHz.
Battery life: 200 hours typical for alkaline
Size: (H x W x L): 4.3 cm x 9.0 cm x 18.5 cm
Lifetime Warranty
1
141
1.0% of reading
Fluke-175
Fluke-177
Fluke-179
Digital Multimeter
Digital Multimeter
Digital Multimeter
RECOMMENDED ACCESSORIES
TPAK
C25
C510
i 200
TL223
Meter hanging kit with magnet
Soft vinyl carrying case
Top grain leather carrying case
AC current clamp
Electrical test lead set
Extech CAT IV True RMS Multimeters + NCV
NEW
True RMS provides accurate readings when measuring distorted or noisy waveforms. Choose a model designed for Electrical, HVAC, or Industrial applications.
Advanced LoZ feature eliminates false readings caused by ghost voltages. CAT IV
safety rating ensures the highest level of protection.
SPECIFICATIONS
EX360
Electrical
EX365
Industrial
EX363
HVAC
• 6000 count white LED backlit display
• Fast 60-segment analog bargraph
• LoZ prevents false readings from ghost voltages
• Built-in Non-contact AC Voltage Detector (NCV)
• Smart Data Hold, Peak Hold, Auto Power off
ORDERING INFORMATION
EX360
EX363
EX365
8 Function TRMS Electrical DMM with NCV
11 Function TRMS HVAC DMM with NCV
10 Function TRMS Industrial DMM with NCV
All Models:
Basic Accuracy (DCV):
NCV Detector:
DC/AC Voltage:
Resistance:
Capacitance:
Frequency:
Diode Test:
Continuity:
Safety:
Approvals:
Dimensions:
Accessories Included:
Warranty:
Additional Functions:
EX363:
Temperature (Type K):
DC/AC Current:
EX365:
DC/AC Current:
0.5%
80 to 1000V (50-60Hz) and 160 to 1000V (50-60Hz)
0.1mV to 1000V
0.1Ω to 40MΩ
1nF to 10mF
0.01Hz to 100kHz
1.5V
Audible and visual
EN61010-1 CAT IV 600V
cULus, CE
6.5 x 3.2 x 1.7" (164x82x44mm)
Test leads, 9V battery, holster with tilt stand and built-in magnet.
Also general purpose bead wire temperature probe on Model EX363
3 years
-40 to 742°F (-40 to 394°C)
600μA, for flame rod measurements
1mA to 10A
NEW
AEMC Digital Multimeters
SPECIFICATIONS
TEST
EQUIPMENT
5212
5215
5217
• TRMS AC
• Non-contact voltage detection
• Low impedance voltage measurement to help
prevent ‘ghost’ readings
• Auto/manual ranging
• Hold function
• Backlight & flashlight
• Sleep mode for extended battery life
• Temperature, frequency & duty cycle functions
(Model 5217)
• Min, Max & Relative measurements (Model
5215 and 5217)
AC:
Basic Accuracy:
Voltage AC/DC:
Current AC/DC:
μAmps AC/DC:
Resistance:
Capacitance:
LCD display:
Ranging:
Power Off:
Non-Contact Voltage Detect:
Max / Min / Max-Min / Δ REL:
Other Features:
TRMS, 1kHz bandwidth
DCV: 0.2%+2cts; ACV: 0.5%+4cts
750VAC/1000VDC
(600V on Model 5212)
6A/10A
(4A/10A on Model 5212)
600/6000μA
(400/4000μA on Model 5212)
60MΩ
(40MΩ on Model 5212)
100mF
6000 count
(4000 count on Model 5212)
Auto or manual
Auto (auto power off can be disabled)
Red display with buzzer (AC only)
Models 5215 & 5217
Diode test, continuity with beeper, LoZ voltage detect, display hold,
low battery indication, flashlight, backlight, removable holster, magnetic
hanger, direct fuse access
Operating Temperature:
-4 to 122°F (-20 to 50°C)
Safety Rating:
CAT III 600 V
Protection:
IP54, 2m drop resistance
Battery:
2 x AA, 500 hour life
Dimensions:
6.7 x 3.1 x 2" (170x80x50mm) with holster
Accessories Included:
Manual, test leads, 2 AA batteries, soft carry case.
Also Thermocouple Adapter with Model 5217
Warranty:
3 years
Additional Functions on Model 5217:
Frequency/Duty Cycle:
1000Hz
Temperature Measure:
-61° to 2192°F (-55° to 1200°C)
ORDERING INFORMATION
AE/2154.07
AE/2154.08
AE/2154.09
Model 5212 4000-count TRMS DMM
Model 5215 6000-count TRMS DMM
Model 5217 6000-count, TRMS DMM w/freq & temperature
141a
Extech Industrial
MultiMeters
Extech Autoranging
MultiMeters
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
L
450
Model 450
•
•
•
•
2000 Count Full Scale
0.05% Basic DCV Accuracy
IR Laser Thermometer
MAX function
L
530
L
Model EX520
• 6000 Count - High Resolution
• 0.09% Accuracy
• Min/Max/Relative/Data Hold
• 20A Max Current
430
Model 430
®
•
•
•
•
•
•
4000 Count Full Scale
TRMS AC
0.03% Basic DCV Accuracy
Capacitance & Frequency
Type K TC Temperature
Relative Function
470
Model 470
all of the Model 430 features plus
• IR Laser Thermometer
SPECIFICATIONS
Measurement Range
DCV
0.1mV to 600V
ACV
0.1mV to 600V
DCA
0.1mA to 20A
ACA
0.1mA to 20A
Ω
0.1Ω to 40MΩ (20MΩ on Model 450)
Models 430 & 470:
Capacitance
0.01nF to 100µF
Frequency
0.001Hz to 10MHz
Duty cycle
0.1 to 99.9%
Type K TC
-4 to 1382°F (-20 to 750°C)
IR Thermometer (Models 450 & 470):
Range
-4 to 518°F (-20 to 270°C)
Spot size
8:1
Emissivity
0.95
All models supplied with CAT III test leads, multi-position tilt stand and
velcro strip for hanging, protective holster with test lead holder, bead
wire temperature probe (except Model 450) and battery.
ORDERING INFORMATION
True RMS Industrial MultiMeter (4000 count)
True RMS Industrial MultiMeter (6000 count)
True RMS Industrial MultiMeter (40,000 count)
Electrical Test Lead Kit
Type K Clamp Probe (212°F/100°C)
Magnetic Hanging Strap
ORDERING INFORMATION
EX450
EX430
EX470
EX/CA310
EX/380905
EX/409996
MultiMeter with IR Thermometer
TRMS MultiMeter
TRMS MultiMeter w/ IR Thermometer
300A AC clamp-on adapter
2000A AC/DC clamp-on adapter
Pouch carrying case
142
TEST
EQUIPMENT
Complete with double molded test leads, magnetic hanging strap, Type K
bead wire temperature probe (-22 to 572°F/-30 to 300°C), carrying
case, and 9V battery.
L
SPECIFICATIONS
Measurement Range (auto or manual ranging)
DCV
0.1mV to 1000V (0.01mV on EX530)
ACV
1mV to 1000V (0.1mV on EX505, 0.01mV on EX530)
DCA
0.1mA to 20A (10A on EX505)
ACA
0.1mA to 20A (10A on EX505)
Ω
EX505: 0.1Ω to 40MΩ
EX520: 0.1Ω to 60MΩ
EX530: 0.01Ω to 40MΩ
Capacitance
EX505: 0.01nF to 100mF
EX520: 0.01nF to 1000mF
EX530: 0.001nF to 40mF
Frequency
Electrical
Electronic
EX505: 5Hz to 1kHz
0.001Hz to 10MHz
EX520: 10Hz to 400Hz
0.001Hz to 40MHz
EX530: 40Hz to 400Hz
0.001Hz to 100MHz
Temperature
-50 to 1382°F / -45 to 750°C
(-4°F/-20°C min on EX505)
Duty Cycle
0.1 to 99.9%
Diode/Continuity Yes
EX505
EX520
EX530
EX/TL810
EX/TP200
EX/HG500
®
520
Model EX505
• 4,000 Count
• 0.5% Accuracy
• Data Hold and Relative
• 10A Max Current
Model EX530
• 40,000 Count - Highest Resolution
• 0.06% Accuracy
• Min/Max/Relative/Data Hold
• 20A Max Current
• Peak Hold (AC only)
Backlit 1" High LCD
Resolution to 0.1mA
CAT III - 600V Rating
Audible & Visual Alerts
Diode/Continuity Check
Three Year Warranty
Built-in IR thermometer
with laser (450 & 470)
L
L
Double Molded Waterproof Case (IP67)
11 Functions
1000V Protection on All Functions
505
True RMS AC
Dual Sensitivity Frequency Functions
Large Backlit LCD
Diode Test Open Circuit 2.8V DC
Auto Power Off with Disable Feature
CATIII-1000V & CATIV-600V Ratings
Drop Proof to 6 Feet
Yokogawa Digital Multimeters
TY720
TY 5 0 0 S e r i e s
• Basic accuracy 0.09%
• True RMS measurement
• 6k count backlit display
• 31 segment bar graph display
• Measures AC/DC Volts to 1kV, AC/DC Amps
to 10A, resistance, continuity, temperature,
frequency, capacitance & diode test.
• Logging-mode memory for 1600 data points
• USB communication & application software
(optional DMM communication package)
• Conforms to safety standards EN61010-1,
1000V CAT III, 600V CAT IV
• Three year warranty
TY700 Series
• Basic accuracy 0.02%
• True RMS measurement
• Dual 7 segment display with backlight
• 50k count with 51 segment bar graph
• Measures AC/DC Volts to 1kV, AC/DC Amps
to 10A, resistance, continuity, temperature,
frequency, capacitance & diode test
• Large capacity logging-mode memory
TY720: 10,000 data
TY710: 1,000 data
• USB communication & application software
(optional DMM communication package)
• Rated 1000V CAT III & 600V CAT IV
• Three year warranty
TY530
SPECIFICATIONS
Model
DC Volts
AC Volts, TRMS:
DC Amps:
AC Amps, TRMS:
TEST
EQUIPMENT
AC + DC:
Resistance:
Low Power Resistance:
Capacitance:
Frequency:
Duty Cycle:
Temperature (Type K):
Logarithm (db) Computation:
Diode/Continuity Test:
Automatic Data Hold:
Min/Max Memory:
Peak Hold:
Data Logging Memory:
PC Connection:
DC Current Source/Sink:
24V Loop Supply:
Step/Sweep mA Output:
TY720
TY710
7 ranges, 50mV - 1000V (best resolution 0.001mV)
6 ranges, 50mV - 1000V (best resolution 0.001mV)
10Hz - 100kHz
10Hz - 20kHz
6 ranges, 500μA - 10A (best resolution 0.01μA)
6 ranges, 500μA - 10A (best resolution 0.01μA)
10Hz - 5kHz
10Hz - 1kHz
Volts, Amps
6 ranges, 500Ω - 50MΩ (best resolution 0.01Ω)
4 ranges, 5kΩ - 5MΩ
--8 ranges, 5nF - 50mF (best resolution 0.001nF)
5 ranges, 10Hz - 100kHz (best resolution 0.001Hz)
10 - 90% (resolution 1%)
-200 to 1372°C (resolution 0.1°C)
Yes
Yes
Yes
Yes
Yes
--10000 points
1000 points
Yes
-------
TY530
TY520
5 ranges, 600mV - 1000V (best resolution 0.1mV)
5 ranges, 600mV - 1000V (best resolution 0.1mV)
40Hz - 1kHz
6 ranges, 600μA - 10A (best resolution 0.1μA)
6 ranges, 600μA - 10A (best resolution 0.1μA)
40Hz - 1kHz
—6 ranges, 600Ω - 60MΩ (best resolution 0.1Ω)
--6 ranges, 10nF - 1000μF (best resolution 0.01nF)
4 ranges, 100Hz - 100kHz (best resolution 0.01Hz)
---50 to 600°C (resolution 0.1°C)
--Yes
Yes
Yes
------1600 points
--Yes
---------
CA450 Process Multimeter
Functionality of a loop calibrator like the CA11E plus a
digital multimeter like the TY520.
—6 ranges, 600Ω - 60MΩ (best resolution 0.1Ω)
----3 ranges, 200Hz - 20kHz (best resolution 0.01Hz)
--—--Yes
Yes
Yes
Yes
--Yes
0 to 20mA (resolution 0.001mA)
20mA load max.
Yes
ORDERING INFO
TY720
TY710
TY530
TY520
CA450
Accessories
YE/92015
• Simultaneous 24 V loop power and mA measurement
• HART mode setting with loop power (250Ω resistance)
• SIMULATE (SINK) function simulates transmitters
• 4-20 mA span/step/auto-step/sweep output
• High accuracy signal measurement: 0.05% @ 30.000mA DC
• Peak/Hold function for DCS power peak-to-peak measurement
• Dedicated sensor modes for direct reading of many sensor
signal types
• Current terminal shutter prevents incorrect connections
• Sensor function handles AC load current measurement
• Meets 600 V CAT IV, 1000 V CAT III safety standards
• Transfer data to a PC via IR-U
• Three year warranty
CA450
5 ranges, 600mV - 1000V (best resolution 0.1mV)
5 ranges, 600mV - 1000V (best resolution 0.1mV)
40Hz - 1kHz
30mA, 100mA ranges (best resolution 0.001mA)
with optional clamp probe
CA450
YE/90051
YE/90056
YE/96001
YE/96095
YE/93029
4.5 digit DMM with expanded data memory
4.5 digit DMM with data memory
3.5 digit DMM with data memory
3.5 digit DMM
Process Multimeter
DMM communication package (includes
IR adapter, USB cable & PC software)
Type K liquid probe, -50° to 600°C
Type K surface probe, -20° to 500°C
400A AC current clamp probe
180A DC/ 130A AC clamp probe
Carrying case
142a
NEW
Fluke Clamp Meters
Five new models offer an impressive array of innovative features with TRMS current ranges up to 2500A,
TRMS voltage ranges to 1000V.
• Measure to 1000A with fixed jaws,
2500A with flexible current probe
• Designed for one hand operation
• Removable display for remote reading up
to 30 ft away (381)
• DCV & DCA measurements (most models)
•
•
•
•
Resistance & continuity functions
Frequency to 500Hz (most models)
Large, backlit display with data hold
In-rush current function (on most models)
for measuring starting current
• Auto shut-off maximizes battery life
AC response
Fluke 375
Fluke 376
Fluke 381
True-rms
True-rms
True-rms
True-rms
AC amps (jaw)
600.0 A
600.0 A
600.0 A
999.9 A
999.9 A
Accuracy
2% ± 5 counts
(48-62 Hz)
2% ± 5 counts
(10-100 Hz)
2% ± 5 counts
(10-100 Hz)
2% ± 5 counts
(10-100 Hz)
2% ± 5 counts
(10-100 Hz)
2.5 @ 600 A
2.5 @ 600 A
3 @ 500 A
2.5 @ 600 A
3 @ 500 A
[email protected] 1000 A
3 @ 500 A
1.42 @ 1000 A
Flexible current probe
–
compatible
compatible
included
included
AC amps (probe)
–
2500 A
2500 A
2500 A
2500 A
Accuracy
–
3% ± 5 counts
(5-500 Hz)
3% ± 5 counts
(5-500 Hz)
3% ± 5 counts
(5-500 Hz)
3% ± 5 counts
(45-500 Hz)
600.0 V
600.0 V
1000 V
Crest factor
AC volts
600.0 V
Accuracy
1% ± 5 counts
(48-62 Hz)
DC amps
Accuracy
DC volts
Accuracy
mV range
Resistance
Accuracy
Continuity Beeper
Capacitance
Frequency
Remote Display
Max Wire Diameter (jaw)
1.5% ± 5 counts 1.5% ± 5 counts 1.5% ± 5 counts
(20-500 Hz)
(20-500 Hz)
(20-500 Hz)
1000 V
–
600.0 A
600.0 A
999.9 A
999.9 A
2% ± 5 counts
2% ± 5 counts
2% ± 5 counts
2% ± 5 counts
2% ± 5 counts
600.0 V
600.0 V
600.0 V
1000 V
1000 V
1% ± 5 counts
1% ± 5 counts
1% ± 5 counts
1% ± 5 counts
1% ± 5 counts
–
–
500.0 mV
500.0 mV
–
6000 Ω
6000 Ω
60k Ω
60k Ω
60k Ω
1% ± 5 counts
1% ± 5 counts
1% ± 5 counts
1% ± 5 counts
1% ± 5 counts
<30 Ω
<30 Ω
<30 Ω
<30 Ω
<30 Ω
10-1000 μF
1-1000 μF
1-1000 μF
1-1000 μF
–
–
–
5-500 Hz
5-500 Hz
5-500 Hz
–
–
–
–
yes
750 MCM
750 MCM
750 MCM
750 MCM
750 MCM
–
yes
yes
yes
yes
MIN/MAX/AVG
–
yes
yes
yes
yes
Backlight
yes
yes
yes
yes
yes
Display Hold
yes
yes
yes
yes
yes
232 x 85 x 45
248 x 85 x 45
248 x 85 x 45
248 x 85 x 45
280 x 88 x 50
CAT III 600V
CAT IV 300V
CAT III 1000V
CAT IV 600V
CAT III 1000V
CAT IV 600V
CAT III 1000V
CAT IV 600V
CAT III 1000V
CAT IV 600V
Rating
Operating Temperature: -10°C to 50°C (14 °F to 122 °F)
Warranty: 3 years
381
1.5% ± 5 counts
(20-500 Hz)
Inrush
Size HxWxD (mm)
TEST
EQUIPMENT
Fluke 374
True-rms
SPECIFICATIONS
Fluke 373
373
New Model
Changes from Old Fluke Model
Fluke 376
Includes all 337 features plus:
• CAT IV 600 V, CAT III 1000 V
• iFlex™ 2500 A ac
• 1000 V ac/dc
Includes all 336 features plus:
• CAT IV 600 V, CAT III 1000 V
• Optional iFlex™ 2500 A ac
• mV dc
Includes all 335 features plus:
• CAT IV 600 V, CAT III 1000 V
• Optional iFlex™ 2500 A ac
• 600 A ac/dc
Includes all 334 features plus:
• CAT IV 600 V, CAT III 1000 V
• Optional iFlex™ 2500 A ac
• True-rms
Includes all 333 features plus:
• CAT IV 300 V, CAT III 600 V
• True-rms
• 600 A ac
Fluke 375
OPTIONAL ACCESSORIES
i2500-10
i2500-18
iFlex Flexible Current Probe 10"
iFlex Flexible Current Probe 18"
ORDERING INFORMATION
Fluke 373
Fluke 374
Fluke 375
Fluke 376
Fluke 381
143
600A True RMS AC Clamp Meter
600A True RMS AC/DC Clamp Meter
600A True RMS AC/DC Clamp Meter
1000A TRMS Clamp Meter with 18" iFlex probe
Remote Display TRMS Clamp Meter with 18" iFlex probe
Fluke 374
Fluke 374
Fluke 373
376
• mV dc
• 60 kΩ
• 1000 μF
• 60 kΩ
• 1000 μF
• Min/Max/Avg
• 1000 μF
• Min/Max/Avg
• 600 A ac/dc
• 1000 μF
• Min/Max/Avg
• 6000 Ω
• 1000 μF
Yokogawa Clamp-On Testers
AC Current
CL100 Series
AC/DC Current
CL200 Series
• AC & DC Current to 2000A
• AC & DC Voltage Measurements
• Resistance / Continuity
• TRMS & Frequency (CL235 & CL255)
• Peak / Data Hold
CL250
L
L
• AC Current to 2000A
• AC Voltage Measurement
• Resistance / Continuity
(CL130 & CL150)
• Data Hold
• IEC CAT III
CL130
ORDERING INFORMATION
YE/CL120
200A AC Clamp-On Tester
YE/CL130
600A AC Multi-Function Clamp-On Tester
YE/CL135
600A AC TRMS Multi-Function Clamp-On Tester*
YE/CL150
2000A AC Multi-Function Clamp-On Tester
YE/CL220
300A AC/DC Clamp-On Tester
YE/CL235
600A AC/DC TRMS Multi-Function Clamp-On Tester
YE/CL250
2000A AC/DC Multi-Function Clamp-On Tester
YE/CL255
2000A AC/DC TRMS Multi-Function Clamp-On Tester
YE/CL320
200A AC Clamp-On Leakage Tester
YE/CL340
400A AC Clamp-On Leakage Tester
YE/CL360
1000A AC Clamp-On Leakage Tester
*same features as CL130, except TRMS
AC Leakage Current
CL300 Series
• AC Current to 1000A
• AC Leakage with 10µA Resolution
• Wide Jaw Opening
• AC & DC Recorder Outputs (CL360)
• Peak / Data Hold
L
CL360
Limited Lifetime Warranty on all Models
Resistance
TRMS
Frequency
Continuity Check
Peak Hold
Data Hold
Recorder Output
300V
(1 range)
-
-
-
-
-
•
-
24mm
0.95"
CAT III 300V
CL130 2000
-
200/600A
(2 ranges)
-
200/600V
(2 ranges)
200Ω
(1 range)
-
-
•
-
•
-
33mm
1.30"
CAT III 600V
CL150 4000
-
400/2000A
(2 ranges)
40/400/750V 40/400/750V 400/4000/40k/400kΩ
(3 ranges)
(3 ranges)
(4 ranges)
-
-
•
-
• •
55mm
2.16"
CAT III 600V
CAT II 1000V
CL220 4000
40/300A
(2 ranges)
40/300A
(2 ranges)
-
-
-
•
-
24mm
0.95"
CAT III 300V
CL235 4000
400/1000A
(2 ranges)
400/600A
(2 ranges)
40/400/600V 40/400/600V
(3 ranges)
(3 ranges)
400/4000Ω
(2 ranges)
• •
• • •
-
33mm
1.30"
CAT III 600V
CL250 4000
400/2000A
(2 ranges)
400/2000A
(2 ranges)
40/400/1000V 40/400/750V
(3 ranges)
(3 ranges)
400/4000Ω
(2 ranges)
-
• •
•
55mm
2.16"
CAT III 600V
CAT II 1000V
CL255 4000
400/2000A
(2 ranges)
400/2000A
(2 ranges)
40/400/1000V 40/400/750V
(3 ranges)
(3 ranges)
400/4000Ω
(2 ranges)
• •
• • • •
55mm
2.16"
CAT III 600V
CAT II 1000V
-
20/200mA
200A
(3 ranges)
-
-
-
-
-
-
-
•
-
24mm
0.95"
CAT III 300V
-
40/400mA
40/400A
(4 ranges)
-
-
-
-
-
-
• •
-
40mm
1.57"
CAT III 300V
-
-
-
-
-
-
• • •
68mm
2.68"
CAT III 300V
CL340 4000
-
-
-
-
-
200mA
2/20/200/1000A
CL360 2000
-
(5 ranges)
144
TEST
EQUIPMENT
CL320 2000
-
Rating
AC Voltage
-
Jaw opening
capacity
DC Voltage
20/200A
(2 ranges)
DC Current
-
Display
CL120 2000
Model No.
AC Current
Functions
NEW
Flir Imaging Clamp Meter
SPECIFICATIONS
• Measure to 600A TRMS
AC/DC
• Built-in thermal imager to
visually identify problems
• Laser & crosshair to pin
point image location
• Center point temperature
measurement
• Narrow jaw fits tight
spaces
• Built-in work light
• VFD mode for testing variable frequency drives
• LoZ voltage mode
• Inrush current check
• Frequency, capacitance,
resistance functions
• Continuity & diode test
• Expandable to 3000A AC
• 10 year warranty
CM174
ORDERING INFORMATION
FLIR CM174
FLIR TA72
FLIR TA74
FLIR TA15
FLIR TA55
FLIR TA52
Imaging 600A AC/DC Clamp Meter
Universal Flex Current Probe 10”(25cm)
Universal Flex Current Probe 18”(45cm)
Soft Sided Carrying Case
Line Splitter
Magnet Mount
Imaging Detector:
Field of View (V x H):
Color Palettes:
Image Frame Rate:
Temperature Measurement:
Temperature Range:
Distance to Spot Ratio:
Temperature Accuracy:
Spectral Response:
Temperature Targeting:
Emissivity Settings:
Electrical Measurements
AC/DC Voltage:
VFD AC Voltage:
LoZ Mode AC Voltage:
LoZ Mode DC Voltage:
DC Current:
AC Current:
VFD AC Current:
Inrush AC Current:
Frequency:
Resistance:
Continuity:
Capacitance:
Diode Test:
Inrush Threshold:
Display:
Jaw Opening:
Category Rating:
Certifications:
Dimensions:
Accessories Included:
FLIR Lepton® microbolometer, 4800 pixels (60 × 80)
38.6° x 50.0°
Iron, Rainbow, Grayscale
9Hz
Center point of thermal image
-13°F to 302°F (-25°C to 150°C)
30:1
±5.4°F (3°C) or ±3% of rdg
8 to 14μm
Class 1 Laser Pointer and Crosshair on display
4 Presets with Custom Adjustment
Range
Basic Accuracy
1000V
±1.0%
1000V
±1.0%
1000V
±1.0%
1000V
±1.0%
600.0A
±2.0%
600.0A
±2.0%
600.0A
±2.0%
600.0A
±3.0%
60.00kHz
±0.1%
6000Ω
±1.0%
600.0Ω
±1.0%
1000μF
±1.0%
1.5V
±1.5%
0.5A min, 100ms integration time
6000 count, 2.0” (50mm) Color TFT
1.38" (35mm), 1250MCM
CAT IV-600V, CAT III-1000V
UL
61 x 111 x 40 mm; Probe: 104 x 34 x 20 mm w/ 700 mm cable
4 AAA batteries, silicone test leads, quick start guide, user manual
NEW
TEST
EQUIPMENT
Amprobe Clamp Multimeter
• Dual display shows volts and
amps concurrently
• True-RMS AC for accurate
measurements
• Low pass filter for current &
voltage measurements on
variable frequency drives
• Amp-Tip function for precise
low current measurement
down to 0.1 amp
• HVAC applications with temperature, DC micro-amps &
capacitance
• Non-contact voltage detection
• In-rush current
• Audible continuity & diode test
• Type K thermocouple
• Data hold
• Auto ranging
ACD-14-PRO
• Auto power off
• Low battery indicator
ORDERING INFORMATION
ACD-14-Pro
600 A TRMS Clamp Multimeter
SPECIFICATIONS
AC Voltage (True-RMS):
DC Voltage:
AC Current (True-RMS):
Amp-Tip AC:
DC Microamps:
Frequency:
Resistance:
Capacitance:
Diode Test:
Type K thermocouple*:
Range
0.0 to 600.0 V
0.0 to 600.0 V
0.00 to 600.0 A
0.00 to 60.00 A
0.0 to 2000 μA
5.00 to 999.9 Hz
0.0 Ω to 60.00 kΩ
60.01 kΩ to 6000 kΩ
200.0 μF, 2500 μF
0.0 to 3.000 V
-40.0 to 752°F
-40.0 to 400°C
Accuracy
±1.0% + 5LSD (50 to 60 Hz)
±1.0% + 5LSD
±1.8% + 5LSD (50 to <100 Hz)
±2.0% + 5LSD (100 to 400 Hz)
±1.5% + 5LSD (50 to 60 Hz)
±1.0% + 5LSD
±1.0% + 5LSD (600 V range)
±1.0% + 5LSD
±1.2% + 5LSD
± 2.0% + 4LSD
± 1.5% + 5LSD
±1.0% + 1.5°F (-40.0 to 99.9°F)
±1.0% + 2°F (100 to 752°F)
±1.0% + 0.8°C (-40.0 to 99.9°C)
±1.0% + 1°C (100 to 400°C)
Non-Contact Voltage:
Continuity Beeper:
Jaw Opening:
Update Rate:
Operating Temperature:
10 to 550 V, 50/60 Hz
On < 10 Ω, Off > 250 Ω
1.18 in (30 mm)
5 per second nominal
32 to 104°F (0 to 40°C), <80% RH up to 88°F (31°C) decreasing
linearly to 50% RH at 104°F (40°C)
Display:
Dual backlit LCD with annunciators
Certification:
cULus, CE
Dimensions (L x W x H):
8.62 x 3.03 x 1.46 in (219 x 77 x 37 mm)
Safety Rating:
CAT III 600 V
Accessories Included:
Manual, test leads, 2 AAA batteries, carry case, Type K thermocouple
*thermocouple accuracy tolerances not included
144a
Extech Clamp Meters
Model EX623
NEW
800A Clamp Meters
400A Dual Input Clamp Meters +
IR Thermometer + Non-Contact Voltage Detect
• AC/DC Current, AC/DC Voltage,
• TRMS AC Voltage & Current measurements
• Dual type K thermocouple input with
•
•
•
•
•
•
Differential Temperature function
• Non-contact Voltage detector with LED alert
• Non-contact IR Thermometer with laser
pointer for locating hot spots
• DC Voltage, DC Current, Resistance,
Capacitance,Frequency & Duty Cycle
functions
• Autoranging with manual override
• Data Hold plus fast Peak Hold for surges
• Complete with test leads, 9V battery, two
Type K bead wire probes
and case
Resistance, Frequency, Capacitance,
Temperature, Diode Test and Continuity
True RMS models
1.2" (30mm) circular jaw opening
Backlit LCD
Peak, Data Hold, Auto power off
DC Current with Zero (EX730)
Complete with test leads, 9V battery,
Type K bead wire probe (EX720, EX730)
and carrying case
200A AC/DC Mini Clamp plus MultiMeter
L Model EX623
L Model EX730
• High resolution to 10mA
• Measures voltage, resistance
and frequency
• Fast 40 segment bargraph
• One touch auto zero for
Model MA640
DC current measurements
600A True RMS Clamp Meters + Non-Contact
Voltage Detect
• TRMS AC Voltage & Current measurements
• Non-contact Voltage detector with
LED alert
• DC Voltage, DC Current, Resistance,
Capacitance, Frequency, Temperature,
Duty Cycle
• Relative Mode for Capacitance
Zero and Offset Adjustment
• Data Hold and MIN/MAX
• Complete with test leads, Type K bead
wire probe, 9V battery and carrying case
• Min/Max
• Data hold and auto power off
• Complete with test leads, wrist strap,
L Model 380941
2 AA batteries and carrying case
30A True RMS AC/DC Mini Clamp
• Measure low AC/DC current with
resolution to 1mA DC and 0.1mA AC
• Also measures voltage
• Fast 40 segment bargraph
• One touch auto zero for
DC current measurements
L Model MA640
• Min/Max
• Data hold and auto power off
• Complete with test leads, wrist strap,
L Model 380942
2 AA batteries and carrying case
TEST
EQUIPMENT
SPECIFICATIONS
Model
AC Sensing:
Display counts:
Jaw size/ Cable size:
EX623
TRMS
4000
1.4" (36mm)
MA640
TRMS
6000
1.5" (40mm)
380941
Averaging
4000
0.9" (23mm); 4/0 AWG
380942
TRMS
4000
0.9" (23mm); 4/0 AWG
AC Current:
DC Current:
Max resolution:
Basic AC/DC Accuracy:
AC/DC Voltage (Max. Res.):
60A, 600A
60A, 600A
0.01A
±2.8%
AC: 600V (1mV)
DC: 600V (0.01mV)
60MΩ (0.1Ω)
4000µF (0.01nF)
10kHz (0.01Hz)
-4 to 1400°F
40A, 200A
40A, 200A
0.01A
±1.0%
400V (0.1V)
Resistance (Max Res.):
Capaciatance (Max Res.):
Frequency (Max. Res.):
Temperatures (Type K):
400µA , 40A, 400A
400µA , 40A, 400A
0.1µA, 0.01A
±1.5%
AC: 600V (0.1V)
DC: 600V (0.01mV)
40MΩ (0.01Ω)
40mF (0.01nF)
100MHz (0.01Hz)
-58 to 1832°F
IR Temperature:
Diode/Continuity:
Data Hold:
Min/Max/Peak:
Safety Rating:
-58 to 518°F
Yes
Yes
Yes
CAT III-600V
—Yes
Yes
Yes
CAT III-600V
145
400mA, 4A, 30A
4A, 30A
AC: 0.1mA, DC: 0.001A
±1.5%
400V (1V)
EX710
Averaging
4000, backlit
1.2" (30mm):
500MCM
800A
—0.01A
±2.8%
600V (0.1mV)
EX720
TRMS
4000, backlit
1.2" (30mm):
500MCM
800A
—0.01A
±3%
600V (0.1mV)
EX730
TRMS
4000, backlit
1.2" (30mm):
500MCM
800A
800A
AC: 0.01A, DC: 0.1A
AC: ±3%, DC: ±2.5%
600V (0.1mV)
400Ω (0.1Ω)
—1000kHz (0.01Hz)
—-
————-
40MΩ (0.01Ω)
40mF (0.001nF)
4kHz (1Hz)
—-
—Continuity
Yes
Min/Max
CAT III-300V
——Yes
Min/Max
CAT III-300V
—Yes
Yes
Peak
CAT III-600V
40MΩ (0.01Ω)
40mF (0.001nF)
4kHz (1Hz)
-4 to 1832°F /
-20 to 1000°C
—Yes
Yes
Peak
CAT III-600V
40MΩ (0.01Ω)
40mF (0.001nF)
4kHz (1Hz)
-4 to 1832°F /
-20 to 1000°C
—Yes
Yes
Peak
CAT III-600V
AEMC Clamp-On Power Meters
• Use on single & 3-phase power to 3MW
• Measure to 1000V AC, DC or AC+DC
• Automatic AC or DC selection
• Ω, Hz & THD measurements
• 10,000 count electroluminescent display
• Fast (1msec) inrush current capture
• 1000V CAT IV & IP54 rated
• Data storage & Bluetooth communication
• 1.89" or 2.36" jaw opening
607
ORDERING INFORMATION
AE/2139.50
AE/2139.51
AE/2139.60
AE/2139.61
Model 405 (TRMS, 1000Vac/dc,
1000Aac/1500Adc, Power, THD)
Model 407 (TRMS, 1000Vac/dc,
1000Aac/ 1500Adc, Energy,
Harmonics, Power, THD, Recording)
Model 605 (TRMS, 1000Vac/dc,
2000Aac/3000Adc, Power, THD)
Model 607 (TRMS, 1000Vac/dc,
2000Aac/3000Adc, Energy,
Harmonics, Power, THD, Recording)
SPECIFICATIONS
MODEL
Measurement Method
Automatic AC/DC Detection
A AC
A DC
A AC+DC
Best A Accuracy
V AC
V DC
V AC+DC
Best V Accuracy
Hz Current
Hz Voltage
Ohm
Audible Continuity
Diode Test
Power Values
Active Power
Reactive Power
Apparent Power
FP / DPF
THDf / THDr
Frequency Analysis
Phase Rotation (2-wire)
True InRush® current
Hold, Min/Max, +/-Peak
REL ΔX / Diff. ΔX/X (%)
Jaw Opening
Number of Values Displayed
Data Recording
Communication Interface
Dimensions
405
407
605
607
TRMS AC/AC+DC/DC
TRMS AC/AC+DC/DC
–
Yes
Yes
0.15 to 1000A (1500A peak)
0.15 to 2000A (3000A peak)
0.15 to 1500A
0.15 to 3000A
0.15 to 1000A (1500A peak)
0.15 to 2000A (3000A peak)
1% of Reading + 3 cts
0.15 to 1000V (1400V peak)
0.15 to 1400V
0.15 to 1000V (1400V peak)
1% of Reading + 3 cts
5.0 to 2000Hz
5.0 to 20.00kHz
0.1Ω to 99.99kΩ
Adjustable
Fixed <40Ω
Adjustable
Fixed <40Ω
Yes
–
Yes
–
Single Phase & Total 3-phase
Single Phase & Total 3-phase
5W to 1000kW
5W to 2000kW
5var to 1000kvar
5var to 2000kvar
5VA to 1000kVA
5VA to 2000kVA
Yes / No
Yes / Yes
Yes / No
Yes / Yes
Yes / Yes
Yes / Yes
Yes / Yes
Yes / Yes
–
25th order
–
25th order
Yes
–
Yes
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
–
Yes / Yes
–
Yes / Yes
1.89" (48mm)
2.36" (60mm)
1
3
1
3
–
Yes
–
Yes
–
Bluetooth
–
Bluetooth
10.70 x 3.62 x 1.61" (272x92x41mm) 11.65 x 4.37 x 1.61" (296x111x41mm)
Megger Clampmeters
DCM330
• Open jaw AC current to 200A
• 0.1V to 1000V AC/DC
• Resistance to 20MΩ
• Continuity buzzer & diode check
• Autoranging
• Non-contact AC voltage
detection
Current measurements and the non-contact
voltage sensor do not need the supplied test
leads. The voltage detection function can
identify the presence of live AC voltage from
50-1000 V at 50-500 Hz.
SPECIFICATIONS
Function
AC Current
AC Volts
DC Volts
Resistance:
Range
Accuracy
200.0 A
±3% ±3d, 50/60 Hz, Avg responding
200.0 / 1000 V
±1.5% ±5d, 50-500 Hz, Avg responding
200.0 / 1000 V
±1% ±2d
200.0Ω - 20.00MΩ ±1% ±2d (2k-2MΩ ranges)
(6 ranges)
Continuity:
<50Ω
Buzzer sounds
Overload Protection: 400 Arms on AC current, 600 Vrms on ohms
Conductor Size:
0.63" (16mm) max.
Display:
31/2 digit, 2000 count
Operating Temp.:
0ºC to 30ºC, <80% RH; 40ºC to 50ºC, <45% RH
Battery:
2 AAA Alkaline
Battery Life:
250hrs typical (auto power off after 10 minutes)
Dimensions:
4.7" x 2.1" x 1.2" (193 x 54 x 21mm)
Safety:
IEC61010-1, CAT III 1000V, CATIV 600V
LEAKAGE CLAMPMETER
• 0.01mA resolution
for measuring earth
leakage currents
• Amp ranges for standard
current measurements
• Analog bargraph display for
trending
• 40mm jaw opening
FORK
MULTIMETER
DCM300E
SPECIFICATIONS
Ranges:
Accuracy:
30/300mA:
0-200A:
200-250A:
250-300A:
Circuit Voltage:
Jaw Capability:
Display:
Data Hold:
Operating Temp.:
Storage Temp.:
Battery:
Dimensions:
Safety:
30mA/300mA/30A/300A (50/60Hz)
±1.2% rdg ±5d
±1.2% rdg ±5d
±3.0% rdg ±5d
±5.0% rdg ±5d
600V AC max.
40mm (1.57")
31/2 digit, 3200 count
Indicated by DH in display
0ºC to +40ºC, <80% RH
-20ºC to +60ºC, <70% RH
2 LR44 button cells
2.5" x 7" x 0.9" (64 x 176 x 23mm)
300V phase to earth, 500V phase to phase CAT III or 600V CAT II
ORDERING INFORMATION
ME/DCM330
ME/DCM300E
Fork Multimeter
Leakage Clampmeter with carrying case
146
Fluke Leakage Clamp Meter
SPECIFICATIONS
• Measure leakage current with 1 μA
resolution, for monitoring of insulation
erosion
• Measure to 60 A, for general
installation needs
• Perform tests without powering down
the installation or disconnecting
equipment
• Advanced shielding ensures accurate
results when measuring near other
conductors
• Easy-to-carry, pocket-sized clamp with
40 mm (1.5") jaw size
• Handy “Display-Hold” button for
capturing readings in hard-to-reach
places
• Auto power-off, with warning buzzer,
saves battery life
• Meets safety standard VDE0404-4 and
VDE0702 for leakage current and
differential current measurement of
electrical appliances
360
ORDERING INFORMATION
Fluke-360
Ranges:
Resolution:
Accuracy:
(50/60 Hz)
Frequency range:
Maximum current:
Digital display:
Bargraph display:
Measurement cycle:
Range switching:
Environment:
Temperature coefficient:
Influence of external
magnetic field:
Influence of
conductor position:
Circuit voltage:
Safety standard:
Battery type:
Battery life:
Conductor diameter
Dimensions:
3 ma, 30 mA, 30 A, 60 A
0.001 mA, 0.01 mA, 0.01 A, 0.1 A
± 1% rdg ± 5d (<50 A)
± 5% rdg ± 5d (>50 A)
15-150 Hz
60 A rms
3200 count LCD
32 segment LCD
2/sec. (digital display), 12 /sec. (bargraph display)
Auto-range
0-50 °C, <80 % RH (non-condensing)
<0.05 % of range/°C (0-18 °C & 28-50 °C, <50 A)
0.0005 % typical (on current value of adjacent cable)
Within accuracy
< 300 Vrms
EN 61010-1, EN 61010-2-032. 300 V CAT II, Pollution Degree 2
3 V Lithium battery (CR2032)
Approx. 90 hours (continuous use)
40 mm (1.57") max.
176 x 70 x 25 mm (6.9" x 2.8" x 1")
Leakage Current Clamp Meter
Hioki AC Power Monitors
NEW
Clamp-On Power HiTester
3169 SPECIFICATIONS
Systems:
Functions:
Ranges:
3169
• Measure up to two 3Ø,
3-wire systems
• Measure up to four 1Ø,
2-wire systems
• 5A to 5000A range
• Simultaneous recording
of demand values
and harmonics
• Ideal for troubleshooting &
energy management
Power:
1Ø 2-wire, 1Ø 3-wire, 3Ø 3-wire,
3Ø 4-wire (50/60 Hz)
ACV, ACA, W, VA, VAr, PF, integrated
power, Frequency, Harmonics
150/300/600V
With 9660: 5-100A, 4 ranges
With 9661: 5-500A, 5 ranges
With 9669: 100A-1kA, 3 ranges
With 9667: 500A-5kA, 2 ranges
With 9694: 0.5A-5A, 3 ranges
75W to 9MW, 108 combination
patterns
Accuracy:
±0.2% rdg ±0.1% f.s. + Clamp
accuracy (for active power)
With 9660: ±0.3% rdg ±0.02% FS
With 9661: ±0.3% rdg ±0.01% FS
With 9669: ±1.0% rdg ±0.01% FS
With 9667: ±2.0% rdg ±1.5 mV
With 9694: ±0.3% rdg ±0.02% FS
Harmonics: Up to the 50th order, ±3% FS +
measurement accuracy
Power:
100 to 240VAC, 50/60 Hz
Dimensions: 8.3"W x 6.3H x 2.4"D
Order clamp-on current sensors separately
• Capture voltage & current wave
forms, power & energy use
• Measure to 780V, 5000A
• Harmonics to the 40th order (-21)
• Display demand and trend graphs
• Store months of data on SD card
• 3 current and 3 voltage channels
PW3360 SPECIFICATIONS
Systems:
Range:
Measurements:
TEST
EQUIPMENT
Power Logger
PW3360
Harmonics:
Memory:
ORDERING INFORMATION
Pulse Input:
Pulse Output:
HK/3169-20
Clamp-On Power HiTester, with voltage leads (order CTs below)
Sampling:
HK/PW3360-20
Power Logger, with voltage leads & AC adapter
HK/PW3360-20-01/5000 PW3360-20 w/ 3 5kA Flex CTs, battery, case, 2GB SD card, software Display:
HK/PW3360-21
Power & Harmonic Logger, with voltage leads & AC adapter
Interface:
HK/PW3360-21-01-5000 PW3360-21 w/ 3 5kA Flex CTs, battery, case, 2GB SD card, software Rating:
HK/9660
100A Clamp-On Sensor
Power:
HK/9669
1000A Clamp-On Sensor
Temperature:
HK/9667
5000A Flexible Clamp-On Sensor
Dimensions:
HK/9694
5A Clamp-On Sensor
Free Software:
147
1Ø 2-wire, 1Ø 3-wire, 3Ø 3-wire, 3Ø 4-wire (50/60 Hz)
Voltage: 90-780V AC, peak: ±1400V
Current: 5-130% of sensor rating
Power: 300.00 W to 9.0000 MW
RMS voltage & curent, peak, phase angle, frequency, active power,
reactive power, apparent power, power factor, active energy, reactive
energy, demand value, demand quality
Voltage , current & power to 40th order plus THD (PW3360-21 only)
132kB internal, optional SD card up to 2GB
Use to record power data & production volume counts simultaneously
When power consumption exceeds a set output rate (1Wh to 100kWh)
14 bits,10.24kHz
3.5" color LCD (320x240)
10Base-T/100 Ethernet with HTTP, USB2.0
CAT III 600V, CAT IV 300V
AC adapter; Rechargeable Ni-MH battery optional
-10 to +50°C, <80% RH
7.1"W x 4.0"H x 1.9"D
Setup and Data Download, Excel Graph Auto-Creation
NEW
Extech AC Power Clamp Meter
SPECIFICATIONS
•Dual LCD display (9999 count)
•Measures 1Ø/3Ø True Power (kW), Apparent
Power (kVA), Reactive Power (kVAR), plus
Horsepower (HP), Power Factor and Phase
Angle with Lead/Lag indicator
•AC+DC μA current with 10nA resolution for
flame rod tests
•Insulation Resistance tests to 100MΩ
•Type K temperature to 1000ºF (900ºC)
•1.6" (40mm) clamp jaw opening
•Max/Min recording with elapsed time indication
•Auto Detect AC/DC Voltage measurements with
simultaneous frequency display
•Diode and Continuity tests
•Category III 600V rating
Function
True Power (W):
Apparent Power (kVA):
Reactive Power (kVAR):
Horsepower (HP):
Phase Angle:
AC Current (Trms):
uA Current (AC+DC Trms):
AC/DC Voltage (Trms):
Resistance:
Resistance (MΩ):
Capacitance:
Frequency:
Temperature (Type K):
®
Complete with deluxe test lead kit, general purpose
Type K thermocouple probe, carrying case and 9V
battery.
380976
Dimensions:
Max Range / Resolution
Basic Accuracy
600kW / 10W
±5%
600kVA / 100VA
±2%
600kVAR/10VAR
±5%
800HP / 0.01HP
±5%
-60 to +60° / 0.1°
±6°
1000A / 10mA
±2%
1000μA / 10nA
±1%
600V / 0.1mV
±1%
1000kΩ / 0.1Ω
±1%
100MΩ / 1kΩ
±5%
7000μF / 1nF
±1.5%
40Hz to 1kHz / 0.1Hz
±0.5%
-58 to 1000°F / 0.1°F
±1%
-50 to 900°C / 0.1°C
±1%
9" x 3" x 1.6" (228 x 76 x 39mm)
ORDERING INFORMATION
EX/380976-K
1000A 1Ø 3Ø AC Power Clamp Meter
Yokogawa AC/DC Clamp-On Power Meter
SPECIFICATIONS
•AC & DC Power up to 600 kW
•True RMS for AC
•Harmonics 1st to 25th order
•Power fluctuation using the ACA Inrush and
Peak Hold functions
•AC & DC Voltage to 1000 V
•AC & DC Current to 600 A
•Frequency, Resistance, Continuity, Diode
check, Power factor
•White LED automatically illuminates front of
jaw when clamping
•Category IV 600V & CAT III 1000V compliant
Function
AC Current:
AC Voltage:
DC Current:
DC Voltage:
Active Power (kW):
Inrush Current:
Resistance:
Frequency:
Harmonics:
Complete with test leads, carrying case and 9V
battery.
Power Factor:
Peak Hold (ACV, ACA):
Dimensions:
Accuracy
±(1.5% Rdg + 5 LSD) @ 50/60Hz
±(1% Rdg + 5 LSD), 50-500Hz
±(1.5% Rdg + 5 LSD)
±(0.7% Rdg + 2 LSD)
±(2.5% Rdg + 11 LSD) AC
±(2.2% Rdg + 22 LSD) DC
±(2.5% Rdg + 20 LSD)
±(1.0% Rdg + 5 LSD)
±(0.5% Rdg + 3 LSD)
1-12: ±(5% Rdg + 10 LSD)
13-25: ±(10% Rdg + 10 LSD)
-1.00 to 1.00
±(3° + 2 LSD)
40% overrange
±(3% Rdg + 15 LSD)
9.6" x 7" x 2.0" (242 x 87 x 51mm)
ORDERING INFORMATION
CW10
YE/CW10
TEST
EQUIPMENT
Range
99.99 / 600.0
99.99 / 999.9
99.99 / 600.0
99.99 / 999.9
9.999 / 99.99 /
600.0
99.99 / 600.0
1k / 10k / 100k
100 / 1000 / 10k
99.99%
AC/DC Clamp-on Power Meter
Amprobe Compact Power Quality Clamp
•AC/DC Voltage up to 600V, AC Current up to
600A, Resistance, Frequency; Active (W),
Reactive (VAR) and Apparent (VA) Power with dual
display Power Factor readout, KWh Recording
•Slim jaws fit in tight spaces & accommodate
conductors up to 1.02” (26mm) diameter
• Auto Selection of AC Volts, DC Volts or AC Amps
•3 phase unbalanced load measurement by calculation of discrete single phase measurements
•Overload protection for all functions to 600V AC
and DC
•Peak hold, data hold, audible continuity test
•Optional PC interface capability
•Safety CAT III 600V
®
Supplied with test leads & battery.
SPECIFICATIONS
Function
AC Current:
AC Voltage:
DC Voltage:
Resistance:
Frequency:
Active Power (W):
Reactive Power (VAR):
Apparent Power (VA):
Power Factor:
Dimensions:
ACD-45PQ
Accuracy
±(1.0% Rdg + 5 LSD) @ 50/60Hz
±(0.5% Rdg + 5 LSD) @ 50/60Hz
±(0.5% Rdg + 5 LSD)
±(1.0% Rdg + 6 LSD)
±(0.5% Rdg + 4 LSD)
±(2.0% Rdg + 6 LSD) @
Harmonics to 10th & PF 0.1 to 0.99
0 to 360.0 kVAR
±(2.0% Rdg + 6 LSD)
@ Harmonics to 10th & PF > 0.7
0 to 360.0 kVA
±(2.0% Rdg + 6 LSD)
@ Harmonics to 10th
0.10 to 0.99
± 3 LSD @ Harmonics to 21th
10.5" x 7" x 3.2" (267 x 178 x 82mm)
ORDERING INFORMATION
AB/ACD-45PQ
147a
Range
40.00 / 400.0 / 600A
600.0V
600.0V
999.9Ω
5.00Hz to 500.0Hz
0 to 360.0 kW
600A Power Quality Clamp
Yokogawa Power Quality Analyzer
Power Quality Measuring
Measure Temporary Malfunction of Power Line
• Captures temporary malfunction phenomena of power line which
causes malfunction or destruction of devices by types (Voltage swell,
Voltage dip, Voltage interruption, Transient overvoltage, Inrush current)
as an event by high sampling rate of 24 μs and RMS calculation.
• Event data contains the type of malfunction, occurred time or occurrence finish time, measured value and waveform of voltage and
current of all channels for approx. 200 ms period.
• Measurement conforms to IEC standard 61000-4-30 Class S
Measure Continuous Malfunction of Power Line
• Measure and display graphs and list of up to the 50th Harmonic
components of voltage, current & power for each phase and in total.
• Displays with up to 10 or 12 waveforms of voltage and current for
each CH.
• Measures, 1 minute flicker (Pst, 1 min), short flicker (Pst) and long
flicker (Plt).
• Displays voltage and current unbalance rate on 3 phase wiring.
Data Analysis & Report Generation Software
• Automatically generates graph and report by simply clicking on file
data displayed on screen.
• Reports Power data, Power quality event data, Main Unit Setting data,
Screen capture data.
CW500 includes 4 voltage
probes, six AA batteries, carrying
case, 2G SD memory card & PC
software. Order current probes
separately.
TEST
EQUIPMENT
ORDERING INFO
YE/CW500-B0-D
YE/CW500-B1-D
Current Probes
YE/96060
YE/96061
YE/96062
YE/96063
YE/96064
YE/96065
YE/96066
Power Quality Analyzer, 120VAC cord, no Bluetooth
Power Quality Analyzer, 120VAC cord, with Bluetooth
Clamp-on Probe 40mm AC 2A for leakage current
Clamp-on Probe 18mm AC 50A for load current
Clamp-on Probe 24mm AC 100A for load current
Clamp-on Probe 30mm AC 200A for load current
Clamp-on Probe 40mm AC 500A for load current
Clamp-on Probe ~110mm AC 1000A flexible type for
load current
Clamp-on Probe ~150mm AC 3000A flexible type for
3ch load current
Vector Display indicates voltage
and current phase difference
and values between input
channels of voltage and current. It also checks whether
the wiring is appropriate.
CW500
Power Measuring & Logging
• Simultaneously measures 3 CH Voltage input, 4 CH current
clamp-on probe input, 2 CH DCV input.
• Displays value list or trend graph screen of Instantaneous/Average/
Maximum/Minimum of Voltage/Current/Power/Power factor/Phase
Angle/Phase Advanced Capacitance Calculation and DCV input.
• Integration Value of Active/Reactive/Apparent Energy is each
displayed by consumption and generation.
• Demand value can be monitored by screens of present power
consumption compared to aimed demand power value.
NEW
CW500 Viewer software provides management of main
unit settings and realtime
measurements via USB.
SPECIFICATIONS
Wiring connections:
1P2W (max. 4 systems), 1P3W (max. 2 systems), 3P3W
(max. 2 systems), 3P3W3 current, 3P4W
Measurements:
Voltage, Current, Frequency, Active power, Reactive power,
Apparent power, Active energy, Reactive energy, Apparent
energy, Power factor, Phase Advancing Condensor, Neutral
current, Demand, Harmonics, Inrush current, Power Quality
(Swell/Dip/Interrupt/Transient overvoltage, Unbalance rate,
IEC flicker
Other functions:
Digital output, Analog DCV input function
Voltage range:
600.0/1000 V RMS
Accuracy:
±0.2% rdg ±0.2% rng. (sine wave, 40-70 Hz)
Allowable input:
1 to 120% (rms) of each range, 200% for peak of each range
Display range:
0.15 to 130% of each range
Crest factor:
3 or less
Sampling speed
24 μs for voltage transient
Current range:
manual or auto, see probe table (below)
Accuracy:
±0.2% rdg ±0.2% rng. + accuracy of clamp-on probe (sine
wave, 40-70 Hz)
Allowable input:
1 to 110% (rms) of each range, 200% for peak of each range
Display range:
0.15 to 130% of each range
Crest factor:
3 or less
Active power range:
See probe table (below)
Accuracy:
±0.3% rdg ±0.2% rng. + accuracy of clamp-on probe (Power
factor 1, sine wave, 40-70 Hz)
Effect of Power Factor: ±1.0% rdg (40-70 Hz, reading at power factor 0.5 ref. 1.0)
Frequency meter:
40 to 70 Hz
Power supply (AC Line): 100-240 V/50-60 Hz/7 VA max.
Power supply (Battery): Alkaline size AA battery LR6 or Ni-Mh (HR15-51) × 6 pcs
Battery life:
3 hours typical (LR6, Backlight OFF)
Internal memory:
Flash memory (4 MB)
External memory card: SD Card (2 GB)
PC communication:
USB Ver. 2.0, Bluetooth Ver. 2.1 + EDR Class2
Display:
320 × 240 (RGB) Pixel, 3.5 inch color TFT, 1 s update rate
Operating temperature: 0 to 45°C, less than 85% RH (without condensation)
Dimensions:
120 (W) × 175 (H) × 68 (D) mm
P o w e r R a n g e s f o r C l a m p - o n P r o b e s - in 1P2W configuration (multiply x2 for 1P3W and 3P3W, x3 for 3P4W)
Clamp-on Probe Model
& Current ranges
Voltage
96061
96062
96063
96064
96065
96066
range:
5000 mA 50.00 A
10.00 A
100.0 A 20.00 A 200.0 A
50.00 A 500.0 A
100.0 A 1000 A
300.0 A 3000 A
600.0 V
3000 W 30.00 kW 6000 W
60.00 kW 12.00 kW 120.0 kW 30.00 kW 300.0 kW 60.00 kW 600.0 kW 180.0 kW 1800 kW
1000 V
5000 W 50.00 kW 10.00 kW 100.0 kW 20.00 kW 200.0 kW 50.00 kW 500.0 kW 100.0 kW 1000 kW 300.0 kW 3000 kW
148
Hioki Power Quality Analyzer
Catch power quality problems on the fly.
Includes: voltage cord set, 6 hour battery pack (rechargeable), AC adapter, USB cable,
basic PC software, carrying case & strap. Order current sensors separately.
SPECIFICATIONS
• Monitor Inrush Current, Voltage
Swells, Voltage Dips, Transient
Over-Voltage, Interruptions
• Measure and Record: Power
and Power Factor,
Active/Reactive Energy,
Demand, Load Changes (with
graph display), Voltage and
Current
• Large 4.7" Color LCD
with Backlight
Measurement lines:
L
3197
& three
9661
sensors
ORDERING INFORMATION
HK/3197
HK/9660
HK/9661
HK/9667
HK/9669
HK/9694
HK/9624-50
Power Quality Analyzer
100A Clamp-on Sensor (300V, Ø15mm jaw)
500A Clamp-on Sensor (300V, Ø46mm jaw)
5000A Flexible Clamp-on Sensor (1000V, Ø254mm jaw)
1000A Clamp-on Sensor (600V, Ø55mm jaw)
5A Clamp-on Sensor (300V, Ø15mm jaw)
Deluxe PQA Analysis Software
Single-phase 2-wire (1P2W), single-phase 3-wire
(1P3W), three-phase 3-wire (3P3W2M & 3P3W3M),
three-phase four-wire (3P4W and 3P4W2.5E)
Measurement line frequency: Auto-detect (50Hz/60Hz)
Voltage range:
600.0V AC (crest factor 2 or less)
Current ranges:
500.0mA, 5.000A, 50.00A, 10.00A, 100.0A,
500.0A, 1.000kA, 5.000 kA (manually switchable
in 2 range sets according to clamp sensor
Measurement items:
Impulsive voltage quality:
Transient overvoltage (Impulse)
RMS voltage quality:
Voltage swell, Voltage dips, Voltage interruption
Power quality:
Frequency, Voltage, Current, Current peak,
Active/Reactive/Apparent power, Power factor
(displaced power factor)
Three phase quality:
Voltage unbalance ratio, Current unbalance ratio
Harmonic quality:
Harmonic voltage, Harmonic current,
(to 50th harmonic)
Harmonic power, Harmonic voltage/current phase
angle, Total harmonic voltage distortion, Total har
monic current distortion (THD-F, THD-R),
Measurement method:
Simultaneous digital sampling of voltage and current
(sampling frequency 10.24 kHz per channel)
Interval settings:
Auto / 1 / 5 / 10 / 15 / 30 / 60 minutes
Recordable period:
125 days maximum; partition memory into four
segments for maximum 31 days of recording each
Internal memory:
4 MB non-volatile
PC Interface:
USB 2.0
Dimensions:
5.1"W x 9.7"H x 2.5"D (128 x 246x 63 mm)
Hioki AC/DC Current Monitor
Includes: carry strap, 4 AA batteries. Order clamp-on sensor separately.
L
SPECIFICATIONS
TEST
EQUIPMENT
3290
Choice of measurement mode:
DC (for battery measurement)
AC+DC RMS (for full-/half-wave rectification measurement)
AC RMS (for current distortion measurement)
PEAK (for peak value measurement of inrush current, etc.)
• Selectable recorder output and response time
• Current integral, operating time/duty measurements (3290-10)
ORDERING INFORMATION
HK/3290
HK/3290-10
HK/9691
HK/9692
HK/9693
HK/9445-02
HK/9400
149
Clamp-On AC/DC HiTester
Deluxe Clamp-On AC/DC HiTester
100A AC/DC Clamp-on Sensor (600V, Ø35 mm jaw)
200A AC/DC Clamp-on Sensor (600V, Ø33 mm jaw)
2000A AC/DC Clamp-on Sensor (600V, Ø55 mm jaw)
AC Adapter
Carrying Case
Current measurement: AC RMS, AC MEAN, AC+DC, DC
Current ranges:
20 to 100A with 9661 clamp
20 to 200A with 9662 clamp
200 to 2000A with 9663 clamp
Frequency:
10 to 1000 Hz
Analog outputs:
DC or AC Current: 2V f.s.
Level output with REC mode
Waveform output with MON mode
Integ./Frequency: 1V/f.s.
Accuracy:
Current: ± 1.3 % rdg. ± 3 digits. (typical)
Frequency: ± 0.3 % rdg. ± 1 dgt. (typical at 50/60Hz)
Frequency response: ± 2.3 % rdg. ± 8 dgt. (DC to 1 kHz)
Digital display:
4 digit, maximum 3000 counts
(9999 counts on 3290-10)
Bar display:
20 segments
Sampling rate:
Fast: 4 times / sec (3290-10: 10times/sec),
Normal: 2 times / sec,
Slow: 1 time / 3sec
Crest factor:
2.5 or less
Max. circuit voltage:
600 V AC rms. (insulated wire)
Dimensions:
6.1"W x 3.6"H x 1.9"D (155 x 98 x 47 mm)
3290-10: Polarity specific integral function measures battery charging and
discharging. Peak current display shows peak charge and discharge.
AEMC Three-Phase Power Quality Analyzers
L
PowerPad™
3945B
SPECIFICATIONS
Electrical
Sampling Frequency
Data Storage
256 samples/cycle
3945B: 4MB
8335: 2GB SD card
3945B: 960V Ø-Ø, 480V Ø-N
8335: 10-1000V Ø-Ø & Ø-N
MN Clamp: 5mA to 100mA/120A or 2 to 240A
MR Clamp: 10 to 1000Aac, 10 to 1400Adc
SR Clamp: 3 to 1200A
AmpFlex™: 10 to 6500A (Crest factor at 6500 = 1)
40 to 69Hz
kW, kVAR, kWh, kVARh, kVAh, K-Factor, Flicker
3945B: PF, DPF
8335: INrush
1st to 50th, Direction, Sequence
9.6V NiMH rechargeable battery pack
AC Supply: 110/230VAC ±20% (50/60Hz)
≥8 hrs with display on;
≥35 hours with display off (record mode)
Voltage (TRMS)
Current (TRMS)
Frequency
Other Measurements
Harmonics
Power Source
Battery Life
Mechanical
Communication
Display
Dimensions
Weight
Safety Rating
All models include three color-coded current probes with 10 ft
leads (MN93 example shown), four* color-coded 10 ft voltage
leads, four* color-coded alligator clips, RS-232 DB9F optically
coupled serial cable, NiMH battery, US 120V power cord,
DataView ® software, carrying bag, soft carrying pouch and
user manual.
*Five in 8335 Kits
ORDERING INFORMATION
AE/2130.75
AE/2130.76
AE/2130.77
AE/2130.78
AE/2130.79
AE/2130.80
AE/2136.21
AE/2136.22
AE/2136.23
AE/2136.24
AE/2136.25
AE/2136.26
™
PowerPad Model 3945B w/MN93 (240A)
PowerPad ™ Model 3945B w/SR193 (1200A)
PowerPad ™ Model 3945B w/24" AmpFlex™ 193-24 (6500A)
PowerPad ™ Model 3945B w/36" AmpFlex™ 193-36 (6500A)
PowerPad ™ Model 3945B w/MR193 (1000AAC/1400ADC)
PowerPad ™ Model 3945B w/MN193 (6A/120AAC)
PowerPad® Model 8335 w/MN93 (240A)
PowerPad® Model 8335 w/SR193 (1200A)
PowerPad® Model 8335 w/24" AmpFlex® 193-24 (6500A)
PowerPad® Model 8335 w/36" AmpFlex® 193-36 (6500A)
PowerPad® Model 8335 w/MR193 (1000AAC/1400ADC)
PowerPad® Model 8335 w/MN193 (5A/120AAC)
Accessories (Optional)
AE/2140.14 Set of three color-coded MN193 probes (6A/120A) with 10 ft leads
AE/2140.17
5A Adapter box
AE/2140.61 Set of four color-coded 30 ft voltage leads
AE/2140.24 Set of three color-coded MN93-30 probes (240A) with 30 ft leads
AE/2140.25 Set of three color-coded SR193-30 probes (1200A) with 30 ft leads
AE/2140.26 Set of three color-coded 24" AmpFlex™ 193-24-30 probes (6500A)
with 30 ft leads
AE/2140.27 Set of three color-coded 36" AmpFlex™ 193-36-30 probes (6500A)
with 30 ft leads
AE/2140.28 One AC/DC Current Probe Model MR193-BK (black connector)
(1000AAC/1400ADC)
AE/2140.29 Set of three color-coded MN193-30 probes (6A/120A) with
30 ft leads
AE/2140.30 Set of three color-coded MR193-30 probes (1000AAC/1400ADC)
with 30 ft leads
150
TEST
EQUIPMENT
Port Optically coupled RS-232
1/4 VGA (320 x 240) color LCD
9.5 x 7 x 2" (240 x 180 x 55mm)
4.6 lbs (2.1 kg)
3945B: 600V CAT III
8335: 1000V, CAT IV
•True RMS single-, two- and three-phase measurements at
256 samples/cycle, plus DC
•Real-time color waveforms
•Easy-to-use on-screen setup
•Automatic current probe recognition and scaling
•True RMS voltage and current measurement
•Measures DC volts, amps and power
•Display and capture voltage, current and power harmonics to
50th order, including direction, in real time
•Capture transients down to 1/256th of a cycle
•Phasor diagram display
•VA, VAR and W per phase and total
•kVAh, VARh and kWh per phase and total
•Neutral current display for three-phase
•Transformer K-factor display
•Power Factor, displacement PF display
•Captures up to 50 transients
•Short-term flicker display
•Phase unbalance (current and voltage)
•Harmonic Distortion (total and individual) from 1st to 50th
•Alarms, surges and sags
•Screen snapshot function captures waveforms or other information
on the display
®
•Includes DataView software for data storage, real-time display,
analysis and report generation
AEMC Single-Phase Power Quality Analyzer
• Stores up to eight screen captures
• Stores up to 1MB of trend recorded data
• Configurable from DataView® software or
front panel
• Captures up to 4096 alarm events using
up to 10 different thresholds
• Displays and records up to 17 different
power quality parameters
• Includes DataView® software for data
storage, real-time waveform display, analysis
and report generation
• Displays Min, Max and Average Volts and
Amps, Crest Factor, Peak value and K-Factor
• Calculates and displays Watts, VARs and VA,
Power Factor and Displacement Power Factor
for single-phase and balanced three-phase
• Displays total harmonic distortion (THD-F and
THD-R) for voltage and current
• Displays individual harmonic values and % for
Volts and Amps through the 50th harmonic
• Captures, displays and stores inrush current
waveforms and statistics
8230 PowerPad®Jr.
All models include current probe with 10 ft
lead and black connector, black & red 10
ft voltage leads and alligator clips, optical
USB cable, NiMH battery, US 120V power
cord, DataView® software, carrying bag,
soft carrying pouch and user manual.
M
Dat aV iew® Sof tware included with Model 8230
• Display and analyze real-time or recorded data on the PC
• Configure all PowerPad® Jr. functions & parameters
• Customize views, templates and reports
• Create and store a complete library of configurations
• Zoom in and out and pan through sections of the graph
• Display waveforms, trend graphs, harmonic spectrums,
text summaries, transients, event logs & stored alarms
ORDERING INFORMATION
AE/2130.82
AE/2130.83
AE/2130.84
AE/2130.85
AE/2130.86
AE/2130.87
PowerPad® Jr. Model 8230 w/MN93-BK (240A)
PowerPad® Jr. Model 8230 w/SR193-BK (1200A)
PowerPad® Jr. Model 8230 w/24" AmpFlex® 193-24-BK (6500A)
PowerPad® Jr. Model 8230 w/36" AmpFlex® 193-36-BK (6500A)
PowerPad® Jr. Model 8230 w/MR193-BK (1000AAC/1400ADC)
PowerPad® Jr. Model 8230 w/MN193-BK (6A/120AAC)
SPECIFICATIONS
Electrical
Voltage (TRMS)
Current (TRMS)
Frequency
Other Measurements
Harmonics
Sampling Frequency
Data Storage
Power Source
Battery Life
Mechanical
Communication Port
Display
Dimensions
Safety Rating
660V Phase-to-Phase, 600V Phase-to-Neutral
MN Clamp: 5mA to 120A or 2 to 240A
MR Clamp: 10 to 1000AAC, 10 to 1400ADC
SR Clamp: 3 to 1200A
AmpFlex®: 10 to 6500A (Crest factor at 6500 = 1)
40 to 70Hz
kW, kVAR, PF, DPF, kWh, kVARh, kVAh, K-Factor,
Flicker, Harmonic Phase Shift, Phase Rotation
THD-R, THD-F, V, A, VA
1st to 50th, Direction, Sequence
256 samples/cycle
1.5MB partitioned for waveforms, alarms & trend
NiMH AA rechargeable battery pack
AC Supply: 120/230VAC (50/60Hz)
>Eight hrs with display on,
>40 hrs with display off (recording mode)
Optically isolated USB
1/4 VGA (320 x 240) color LCD
8.3 x 4.3 x 2.4" (211 x 108 x 60mm)
EN 61010, 600V Cat. III, Pollution Degree 2
AEMC Power Quality Meter
TEST
EQUIPMENT
• Displays Min, Max and Average Volts and
Amps, Crest Factor, Peak value and K-Factor
• Calculates and displays Watts, VARs and VA,
Power Factor and Displacement Power Factor
for single-phase and balanced three-phase
• Displays total harmonic distortion (THD-F and
THD-R) for voltage and current
• Displays individual harmonic values and % for
Volts and Amps through the 50th harmonic
• Captures and displays inrush current
• Calculates & displays phase rotation & RPM
All models include current probe with 10 ft
lead & black connector, black & red 10 ft
voltage leads and alligator clips, optical
USB cable, six 1.5V batteries, two safety
8220 test probes, DataView® software, carrying
bag, soft carrying pouch and user manual.
M
Three-line backlit digital display with custom icons
ORDERING INFORMATION
AE/2130.91
AE/2130.92
AE/2130.93
AE/2130.94
AE/2130.95
AE/2130.96
151
Power Quality Meter Model 8220 w/MN93-BK (240A)
Power Quality Meter Model 8220 w/SR193-BK (1200A)
Power Quality Meter Model 8220 w/24" AmpFlex® 193-24-BK (6500A)
Power Quality Meter Model 8220 w/36" AmpFlex® 193-36-BK (6500A)
Power Quality Meter Model 8220 w/MR193-BK (1000AAC/1400ADC)
Power Quality Meter Model 8220 w/MN193-BK (6A/120AAC)
• Displays °F or °C & resistance to 2000Ω
• Conducts continuity and diode tests
• Stores up to nine complete sets of readings
for all volt, amp, power, harmonics and other
measurements
• Configurable from DataView® software or
front panel
• Operates off batteries or optional AC adapter
• Includes DataView® software for data
storage, real-time waveform display, analysis
and report generation
SPECIFICATIONS
Voltage (TRMS)
Current (TRMS)
Frequency
Other Measurements
Sampling Frequency
Data Storage
Power Source
Communication Port
Dimensions
660V Phase-to-Phase, 600V Phase-to-Neutral
MN Clamp: 5mA to 120A or 2 to 240A
MR Clamp: 10 to 1000AAC, 10 to 1400ADC
SR Clamp: 3 to 1200A
AmpFlex®: 10 to 6500A (Crest factor at 6500 = 1)
40 to 70Hz
kW, kVAR, PF, DPF, VA, Harmonics, Phase Rotation,
Temperature, RPM, Resistance, Continuity, Diode Test
256 samples/cycle
Stores nine sets of readings
Six 1.5V AA Alkaline batteries (>8hr life with display on)
AC Supply: 120/230VAC (50/60Hz) – optional
Optically isolated USB
8.3 x 4.3 x 2.4" (211 x 108 x 60mm)
Fluke Three Phase Power Quality Analyzers
The Fluke 435 and 434 three-phase power
quality analyzers help locate, predict, prevent and troubleshoot problems in threephase and single-phase power distribution
systems. The new IEC standards for flicker,
harmonics and power quality are built in.
• Analyzer trends using cursor & zoom tools
even while background recording
• Seven hours operating time per charge on
NiMH battery pack
•Transfer data files to your PC for reporting
and analysis using FlukeView® software
435 Includes: Hard carrying case with
rollers, four flexible current probes (i430flex), five test leads and clips, battery charger, FlukeView software, Power Log software,
optical USB cable, color localization set,
Getting Started manual, Users manual.
434 Includes: Hard carrying case, four current probes (i400s), five test leads and clips,
battery charger, FlukeView software, optical
USB cable, color localization set, Getting
Started manual, Users manual.
Feature
ORDERING INFORMATION
3Ø Power Quality Analyzer
3Ø Power Quality Analyzer
434
SPECIFICATIONS
System Configuration
• Automatic transient capture:
never miss an event
• Auto Trends: don't waste time
setting up recordings
3 Year warranty
Fluke 435
Fluke 434
435
Measure voltage, current, dips, swells,
interruptions, harmonics, inter-harmonics,
flicker, power, energy, transients, frequency,
unbalance, inrush, EN50160 overview
Logger function with multiple parameters
Optional*
Mains signalling
Optional*
Current probes
3000A flexible (4)
40/400A clamp (4)
Memory
16MB
8MB
Software
Power Log & FlukeView
FlukeView
IEC61000-4-30 Class A compliance
Safety rating
CAT IV 600 V/CAT III 1000 V
Battery life
Up to 7 hours/charge
*Optional function can be added with upgrade kit.
• Four voltage and four current
channels capture waveform data
on all phases simultaneously
• Meter display of phase readings
Voltage Inputs
Maximum
Bandwidth
Accuracy (ac+dc)
Current Inputs
Range
Nominal Frequency
Accuracy (ac+dc)
Watts (VA, VAR)
Accuracy
Sampling
Logger Function
Display
Power
1Ø+neutral, 1Ø split phase, 1Ø IT no neutral, 3Ø WYE, 3Ø Δ,
3Ø IT, 3Ø hi leg, 3Ø open leg, 3Ø 2-element, 3Ø 2½-element
Four (3 phases + neutral), dc coupled
1000V rms, 6kV maximum peak measured
>10kHz, up to 100kHz for transient display
435: ±0.1% of nominal voltage, 434: ±0.5% of nominal
Four ((3 phases + neutral), dc coupled
Determined by clamp-on probes used
40-70Hz, BW >10kHz
435: ±0.5%±20d, 434: ±1%±5d (with supplied probes)
1.0-20.00MW (resolution 0.1 to 1 kW)
435: ±1%±10d, 434: ±1.5%±10d
16 bit resolution. 200k samples/second max
Captures up to 10000 events, 100 parameters/phase
4.5" x 3.4" Color LCD, 320x240 pixel
115/230V ac or battery, built-in battery charger
Fluke Power Quality Analyzer
• Voltage, current and power
harmonics up to 51st
• Total harmonic distortion (THD)
• Phase angle of individual
harmonics
• Watts, power factor, displacement power factor, VA and VAR
• Voltage and current waveforms
• Calculates 3Ø Power on
Balanced Load from 1Ø
Measurement
• Use cursors to read time and
date of sags and swells.
• Catch voltage transients and
waveform distortion
• See current at the instant of
voltage events
• Catch and save up to
40 transients
• Correlate the cause of distortion
with time and date stamps
• 3 Year Warranty
The Fluke 43B includes a hard case, voltage and current
probes, FlukeView® PC software and cable, line voltage
adapter/battery charger, applications manual, power quality video and user’s manuals.
ORDERING INFORMATION
Fluke 43B
151a
Power Quality Analyzer
The Fluke 43B Power Quality Analyzer performs the measurements you need to maintain power systems,
troubleshoot power problems and diagnose equipment failures. All in a rugged handheld package.
Function
Measurement
Accuracy/Selection
Volts
Amps
Mains Frequency
Watts, VAR, VA
PF, DPF
Sags & Swells
Transient Capture
5.000V-600V RMS (AC & DC)
50.00A-50.00kA RMS (AC & DC)
40.0-70.0Hz
250W-2.5MW
0.25-1.00
Voltage and Current
40 ns pulse width
Up to 40 transients
1A to 1000A
500.0Ω to 30.00MΩ
50.00nF to 500.0μF
Dc, ac, ac+dc, peak,
peak-peak, Hz, duty cycle,
phase, pulse width, crest
factor
All functions
V/A/Hz, Power, Harmonics,
Ω/Cap, Temperature, Scope
±(1%+10d)
±(0.5%+2d)
±(4%+4d)
±0.04
4 min-16 days selectable
Select 20/50/100/200% above
or below line voltage
1s to 5 min selectable
±(0.6%+5d)
±(2%+10d)
Sampling rate: 25MS/sec
Bandwidth:
Voltage BW (Channel 1): 20MHz
Current BW (Channel 2): 15kHz
10 screens
4 min-16 days selectable
parameters in each display mode
Thrush Current
Ohms
Capacitance
Scope
Screen Saves
Recording
Battery life: Rechargeable Ni-Cd pack (charger included), 6 hrs typical (continuous)
OPTIONAL ACCESSORIES
i200s
80i-1000s
i2000flex
80TK
80T-IR
PAC91
240A AC current probe
1000A AC current probe
2000A flexible AC current probe
Thermocouple module
Non-contact infrared temperature probe
Parallel printer adapter
Extech Infrared Thermometers
Mini IR Thermometers
High Temperature IR Thermometer
Compact thermometers with choice
of 500°F or 1200°F maximum reading
Measures surface temperature to 1832°F
with 50:1 distance to target ratio
• Measures small surface areas at greater
distances
• Adjustable emissivity increases accuracy
for different surfaces
• Displays MAX, MIN, average and difference
(MAX-MIN) values
• Audible high/low alarm alerts user when
temperature exceeds set limits
• Large, backlit LCD display with automatic
Data Hold feature
• Complete with 9V battery and hard
carrying case
• Model 42500 measures -4 to 500°F
(-20 to 260°C) with 1° resolution
• Model 42510A measures --25 to 1200°F
(-50 to 650°C) with 0.1° resolution up
to 1000°
• Built-in laser pointer and backlit LCD
display
• Adjustable emissivity (42510A)
• Field of view: 42500 6:1, 42510A 12:1
• Complete with 9V battery and carrying
case
L Model 42510A
Dual Laser IR Thermometers
Two laser pointers converge to 1" target
spot
• Measure to 1800°F (1000°C) with 1°
resolution
• 12" or 30" laser convergence distance
• Fast 0.15 second response time
• White backlit dual LCD display
• Adjustable emissivity increases accuracy
• Lock function for continuous readings
• Adjustable high/low setpoints with
audible alarm alerts
• Complete with 9V battery and carrying
case
Dual Laser IR Thermal Scanner
L Model 42512
ORDERING INFORMATION
500° Mini IR Thermometer
EX/42510A
1200° Mini IR Thermometer
EX/42511
Dual Laser IR Thermometer - 12" Convergence
EX/42512
Dual Laser IR Thermometer - 30" Convergence
EX/42545
High Temperature IR Thermometer
Dual Laser IR Thermal Scanner
EX/IR201A
Pocket IR Thermometer
Tilt-adjustable LCD display with white backlight
and dual bargraphs
• Measures -58 to 500°F / -50 to 260°C
• Dual laser converges at 20" distance for
ideal 1" target spot
• Fast 150ms sample rate
• 5 user programmable threshold settings
• Audible alarm volume increases as
temperature increases or decreases
• 3 color LED indicates High (red), Normal
(green) or Low (blue) when scanning
• Min/Max storage & Trigger Lock
• Complete with 9V battery & case
L Model IRT500
Pocket IR Thermometer
EX/42500
EX/IRT500
L Model 42545
Handy troubleshooting thermometer with
laser pointer
• Measures from -4°F to 518°F
(-20° to 270°C)
• Built-in laser pointer to improve aim
• Adjustable emissivity
• Data Hold & Max Hold
• 6:1 field of view
• Complete with two AAA batteries and
carrying case
L Model IR201A
Model
Temperature:
(non-contact)
Laser Pointer:
42500
-4 to 500°F
-20 to 260°C
Single
42510A
-25 to 1200°F
-50 to 650°C
Single
42511
-58 to 1100°F
-50 to 600°C
Dual
42512
-58 to 1832°F
-50 to 1000°C
Dual
425 45
-58 to 1832°F
-50 to 1000°C
Single
IRT5500
-58 to 500°F
-50 to 260°C
Dual
IR201A
-4 to 518°F
-20 to 270°C
Single
Basic Accuracy:
(non-contact)
±2.5% of reading
or ±4°F / 2°C
±1% of reading
± 2°F / 1°C
±1% of reading
± 2°F / 1°C
±1% of reading
± 2°F / 1°C
±2% of reading
±4°F / 2°C
±(1% of reading
+3.3°F / 1.5°C)
±(2.5% of rdg
+3.6°F / 2°C)
1°
0.95 fixed
6:1
0.1° up to 999.9° 0.1°
0.1-1.00 adjust
0.1-1.00 adjust
12:1
12:1
0.1°
0.1-1.00 adjust
30:1
0.1° up to 199.9°
0.1-1.00 adjust
50:1
0.1°
0.95 fixed
20:1
0.1°
0.1-1.0 adjust
6:1
3.2 x 1.7 x 6.7"
82x44x170mm
4.9oz (140g)
3 years
3.2 x 1.6 x 6.3"
82x42x160mm
6.4oz (180g)
3 years
5.7 x 4.1 x 1.6"
146x104x43mm
5.7oz (163g)
3 years
3.9 x 2.2 x 9"
100x56x230mm
10.2oz (290g)
3 years
6.6 x 3.2 x 2.3"
168x82x58mm
5.7oz (163g)
1 year
3.7 x 2 x 1"
94x51x25mm
2.7oz (76g)
1 year
(whichever is greater)
Max. Resolution:
Emissivity
Field of View:
(Distance to Target)
Dimensions:
Weight
Warranty:
<932°F (500°C)
5.7 x 4.1 x 1.6"
146x104x43mm
5.7oz (163g)
3 years
152
TEST
EQUIPMENT
SPECIFICATIONS
Yokogawa Insulation Testers
2406E Analog Insulation Tester
Model
• 3 Ranges
• Discharge Function
• Portable Case for Hanging
Tester from Neck
• Sky-Blue EL Illumination
Rating
31
41
32
42
L
33
2406E
YE/2406
43
34
MY10 Analog Insulation Tester
44
• Single Range Models
• AC Voltage Measurement
Function (needle and LED)
• Automatic Discharge
Function (LED)
• Easy to Use Pull-Up Switch
35
45
MY10
L
MY40 Digital Insulation Tester
• Four Voltage Ranges
• Memory Function
• Comparator Function with
Sound Alert
• Auto Discharge Function
• Large LCD Display with
Stable Indication
• AC Voltage/Resistance
Measuring Functions
• Conductor Resistance
MY40
Measurement
01
02
YE/MY10 03
04
05
YE/MY40 01
Measure
50V / 10M
125V / 20M
125V / 20M
250V / 50M
125V / 20M
250V / 50M
500V / 100M
250V / 50M
500V / 100M
1000V / 2000M
250V / 500M
500V / 1000M
1000V / 2000M
125V / 20M
250V / 50M
500V / 100M
500V / 1000M
1000V / 2000M
125V / 200M
250V / 200M
500V / 2000M
1000V / 2000M
Display
Illumination
Analog
Meter
Back-lit EL display
(41/42/43/44/45)
Analog
Meter
Phosphorescent
scale
3.5 digit &
400Ω
LED Lighting
bargraph LCD
300V
AC
600V
AC
250VAC
300VAC
500VAC
600VAC
Lifetime Warranty on All Models
Dimensions:
2406
MY10, MY40
4.7"x4.3"x2.4" (120x110x60mm)
4.9"x4.1"x2.1" (125x103x53mm)
2406
MY10, MY40
6 AA Batteries (included)
4 AA Batteries (included)
Power:
L
TEST
EQUIPMENT
Fluke Infrared Thermometers
SPECIFICATIONS
• Dot Laser Sighting
• Comfortable Pistol Grip
• Large Backlit Display
• Hi/Lo Alarms
MODEL
• Displays Difference Between
Two Measurements
Spot Distance
62 MAX+
-30 to 500
-30 to 650
Range °F
-22 to 932
-22 to 1202
Emissivity
• Small Size Easily Fits in Toolbox or
Clips to Belt Loop
• 3-Meter (9.8-Foot) Drop Tested
• IP54 Dust & Water Resistance
Min/Max/Avg/Diff
Hi/Lo Alarms
L
62 MAX
62 MAX
Range °C
62 MAX
62 MAX+
153
Single Laser Infrared Thermometer
Dual Laser Infrared Thermometer
12:1
0.10-1.00
0.10-1.00
Yes
Yes
Yes
Yes
Display Resolution
0.1°C (0.2°F)
0.1°C (0.2°F)
Basic Accuracy
1.5% or 1.5°C
1.0%or 1.0°C
Response Time (95%)
Laser Sighting
ORDERING INFORMATION
10:1
<500 ms
<300ms
Single
Dual
Battery:
Size:
Weight:
One AA (included)
6.88x3.34x2.95" (175x85x75mm)
9 oz (255g)
Operating Temp:
0 to 50°C, <90% RH non-condensing
Yokogawa Thermometers
TM10 Thermistor Data
Collecting Thermometer
TM20 TC Data Collecting
Thermometer
• Two Channel
Simultaneous
Measurement
• Measure Type K/J/E/T
Thermocouples,
mV Inputs &
Infra-Red Sensors
• Display Channel
Readings, Min, Max,
Average & Difference
• Switch Between
External Probe,
Infra-Red Sensor
and Built-In Sensor
• Measure from
-30 to 200°C
TX10 Series
• Measure J/K/T/E
Thermocouples
• 3 1/2 Digit Display for
Resolution to 0.1°C
• IP54 Drip Proof Case
• Two Channel
Measurement
(TX10-03)
• 10 Measurement
Storage (TX10-02/03)
• Min & Max Storage
(TX10-02/03)
• Temperature
Difference Display
(TX10-03)
SPECIFICATIONS
TM10
TM20
TX10
Range
-30 to 200°C (-22 to 392°F)
TC same as TM20
Accuracy
±0.3°C (0-100°C)
Resolution
0.1°C
Operating Temp
-20 to 50°C
K -200 to 1372°C (-328 to 2501°F)
J
200 to 1000°C (-328 to 1832°F)
E -200 to 700°C (-328 to 1292°F)
T
-200 to 400°C (-328 to 752°F)
TC ±0.3% rdg ±0.3°C (>-100°C)
V ±0.1% rdg ±0.2% range
TC 0.1°C
V 0.001V
mV 0.1mV
0 to 50°C
±0.3% rdg ±0.7°C (-100 to 200°C)
0.1°C (below 200°C)
0 to 50°C
TM10 & TM20 Common Features
• Backlit LCD Display
• IP54 Drip Proof Case
• 1 Second to 24 Hour Measuring Intervals
• Data Capacity up to 20000 Readings
• Hi/Lo Alarms
• RS232 Port for PC Interfacing
• Easy PC Data Management (Automatic Layout in Excel)
Collector mode records the measured temperature along with
the measured item, operator name, date/time of measurement
in response to a key action. Test comments can also be recorded.
Logging mode continuously records the measured temperature
at a preset time interval.
ORDERING INDFORMATION
YE/TM10
Thermistor Data Collecting Thermometer
YE/TM20
TC Data Collecting Thermometer
YE/TX10-01
Single function, 1 channel Thermometer
YE/TX10-02
Multi-function, 1 channel Thermometer
YE/TX10-03
Multi-function, 2 channel Thermometer
Order probes and carrying case separately
ACCESSORIES
TM10 Accessories
YE/90010
150mm needle probe
YE/90011
120mm sharp needle probe
YE/90012
Surface probe
YE/90013
Rounded probe (for liquids)
YE/93010
Soft case
TM10 & TM20 Accessories
YE/90003
Non-contact probe
YE/91011
RS-232 PC cable
TX10 & TM20 Accessories
YE/90020
Type K rounded probe
YE/90023
Type K needle probe
YE/90030
Type K surface probe
YE/245907
Type K bead
YE/93012
Soft case
153a
Hioki Megohm Testers
• 5 test ranges to 1000V
• Insulation readings to 4000MΩ
• Pass/Fail indicator
• AC/DC voltage measurements
• Live wire warning
• Continuity check at 200mA
• Drop proof from 1m (3.3ft)
• Tests insulation on transformers,
cables & motors
• Calculates PI (Polarization Index)
and DAR (Dielectic Absorption
Ratio)
• Temperature measurement
& compensation
• Step voltage testing
• Leakage current display
3455
IR4056
SPECIFICATIONS
Insulation Resistance:
Test voltage:
250V, 500V, 1kV, 2.5kV, 5kV DC
25V step (<1kV), 100V step (>1kV)
Manual adjust:
Resistance:
0.00MΩ - 5TΩ in 7 ranges
(±5% rdg. ±5d for test current >100nA)
Leakage current:
1.00nA-1.2mA in 6 ranges
(±2.5% rdg. ±5d above100nA)
Voltage Measure:
50-750V AC, 50/60Hz; 50-1000V DC (±5% rdg. ±5d)
Temperature:
-10.0 to 70.0°C (±1.5°C)
PI, DAR test:
Times are user programmable.
Step voltage test:
500V-2.5kV in 500V steps, 1kV-5kV in 1kV steps
Displays the resistance based on reference
Compensation:
temperature. Compatible to 10 insulation materials
Timer:
30s to 30min
Manual recording: 100 data
Data memory:
Interval recording: 360 times x 10 data
Automatic discharge after measurement
Energy discharge:
Digital and bargraph display, with backlight
Display LCD:
Time, date, test voltage, timer, battery level
Display Info:
For USB data transfer and report editing
PC software:
6 AA batteries
Power supply:
CAT IV 600V, CAT III 1000V
Standards:
10.2"W x 9.9"H x 4.7"D (260 x 251 x 119mm)
Dimensions:
SPECIFICATIONS
Insulation Resistance:
Ranges:
Accuracy:
Low Resistance:
Accuracy:
AC Volts Measure:
Accuracy:
DC Volts Measure:
Accuracy:
Response time:
Other functions:
Power Supply:
Dimensions:
50 / 125 / 250 / 500 / 1000V DC test voltage
100 / 250 / 500 / 2000 / 4000MΩ
±4% rdg.
10.00 / 100.0 / 1000Ω ranges
±3% rdg. ±2d
420.0 & 600V ranges, 50/60Hz
±2.3% rdg. ±8d
4.200 to 600V in 4 ranges
±1.3% rdg. ±4d
0.8 sec for Pass/Fail decision
Live wire warning, automatic discharge, DC/AC detection
4 AA batteries (20 hr life)
6.3"W x 7.0"H x 2.1"D (159 x 177 x 53mm)
ORDERING INFORMATION
HK/3455-01
HK/IR4056-20
HK/L9787-91
HK/L9788-11
HK/9631-01
HK/9750
HK/9459
HK/9753
5kV MΩ HiTester with 3m leads, USB cable, PC software
1kV MΩ HiTester with test leads & neck strap
Breaker pin for IR4056
Test lead set with remote switch for IR4056
Temperature sensor for 3455 (1m)
10m Test Leads for 3455
Rechargeable Battery pack for 3455
AC adapter for 3455
Fluke MegOhmMeters
1550C
1507
SPECIFICATIONS
SPECIFICATIONS
Insulation Resistance:
Ranges:
0.01 MΩ to 10 GΩ (1507); 0.01 MΩ to 4000 MΩ (1503)
Test Current:
1mA max.
Test Voltage:
50, 100, 250, 500, 1000 V (500 & 1000 V on 1503)
Basic Accuracy:
±(1.5% rdg + 5d) up to 2000 MΩ
Resistance:
0.01 Ω to 20.00 kΩ
Basic Accuracy:
±(1.5% rdg + 3d)
Voltage:
0 – 600.0 V DC or AC (50-400Hz)
Live Circuit Indicator:
Inhibits insulation resistance test if >30V AC/DC present
Operating Temperature: -20 to 55°C
Rating:
CAT IV 600V
Includes test leads, test probes, alligator clips, protective holster & batteries.
ORDERING INFORMATION
Fluke 1503
Fluke 1507
Fluke 1550C-KIT
Fluke 1555-KIT
1kV Handheld Insulation Resistance Tester
Deluxe 1kV Handheld Insulation Resistance Tester
5kV Insulation Tester Kit
10kV Insulation Tester Kit
5kV & 10kV Insulation Testers
• Resistance to 2TΩ
• Ramp function
• DAR & PI calculations
• Auto-discharge
• 99 memory storage
• Live circuit voltage warning
• PC interface
Insulation Resistance:
250V
500V
1000V
2500V
5000V
10000V
Step Size:
Leakage Current:
Capacitance:
Timer:
Power:
Charger:
Operating Temperature:
200 kΩ – 50 GΩ
200 kΩ – 100 GΩ
200 kΩ – 200 GΩ
200 kΩ – 500 GΩ
200 kΩ – 1 TΩ
200 kΩ – 2 TΩ (1555 only)
50V up to 1000V, then 100V
1 nA – 2 mA
0.01 μF – 15.00 μF
0 – 99 minutes
12V rechargeable battery, >750 tests per charge
85-250VAC
-20 to 50°C
Kit includes test cables, ac power cord/charger, infrared USB cable, hard carry case,
FlukeView® Forms PC software
154
TEST
EQUIPMENT
Handheld MegOhmMeter
• Insulation resistance to 10GΩ (1507)
• Test voltages to 1000V
• Calculates Polarization Index & Dielectric
Absorption Ratio (1507)
• AC/DC voltage measure to 600V
• Pass/Fail function for repetitive tests (1507)
• Remote probe for hard-to-reach tests
Megger® Insulation Resistance Testers
MIT515 and MIT525 5kV Testers
NEW
This new generation of insulation testers offers increased measurement range, better
accuracy, longer battery life, additional functionality and improved safety features.
MIT515
MJ15
MJ15 and BM15
The BM15 and MJ15 are compact 5-kV
insulation testers that are simple to use
and provide a quick, accurate reading of
insulation resistance. Both instruments
offer four test voltages (500 V, 1 kV, 2.5 kV,
5 kV), analog scales and measurement
sensitivity to 20 GΩ.
These models include “pass/fail” display
overlays for a rapid “go/no go” testing
and trend analysis.
The BM15 is powered by 8 “AA” or
rechargeable alkaline batteries while
the MJ15 includes a hand-crank generator in addition to battery power.
A rugged, portable tester designed for years of
trouble free operation:
• Three industry standard tests can be
programmed and run automatically
• Insulation resistance (IR)
• Dielectric absorption (DAR)
• Polarization index (PI)
• Resistance measurements to 10 TΩ
with 5% accuracy up to 1 TΩ
• Voltage, capacitance & leakage current
measurements
• Test voltage can be set in 10 V increments
from 50 V to 1 kV, and in 25 V increments
above 1 kV
• Timer control, timer display and alarm limit modes
• Test lockout when an external voltage is present, for redundant safety
• Dual operation from AC line or rechargeable batteries
MIT515
MIT525
All the features of the MIT515 plus expanded capabilities to afford the skilled operator more flexibility in analyzing and reporting the condition of capital equipment:
• Ramp test, auto step voltage (SV) test, auto dielectric discharge (DD) test
• Advanced memory functions with recall to screen, real time clock, time/date stamped
results and data downloaded via RS232 or USB ports
• Includes PowerDB Lite software for documenting test results
TEST
EQUIPMENT
MIT1025 10kV Insulation Tester
Same features and functions as the MIT525,
but with 10kV maximum output:
• Test voltage range from 50 V to 10 kV,
in 10 V increments to 1 kV and 25 V
increments above 1 kV
• Increased measurement range to 20 TΩ,
for testing the best insulating materials
• Automatic performance of standardized
tests, including Step Voltage, Dielectric
Absorption Ratio and Dielectric Discharge
• Capacitance measurements from 1 nF to
25 μF, providing additional equipment
diagnostic information
• RS232 & USB ports for downloading test results • A
'quick start' guide in the lid to make field operation
simple and user-friendly
ORDERING INFORMATION
NEW
Catalog No.
ME/MJ15
ME/BM15
ME/MIT515
ME/MIT525
MIT1025
IEEE43:2000 "IEEE Recommended Practices for Testing Insulation Resistance of
Rotating Machinery" recommends testing machines rated above 12kV at 10kV.
The Polarisation Index test is performed on equipment and cables to assess
the general condition of the insulation before applying potentially destructive
test voltages.
The new MIT 5kV & 10kV models easily perform both these tests.
155
ME/MIT1025
Test Voltage (V dc)
Resistance
500
100 kΩ – 20GΩ
1000
2500
5 kV
250
10 kΩ – 10 TΩ
500
1000
2500
5 kV
250
10 kΩ – 10 TΩ
500
1000
2500
5 kV
500
10 kΩ – 20 TΩ
1000
2500
5 kV
10 kV
Megger® Insulation Resistance Testers
MJ Series
The MJ159 is the recognized industry standard, upgraded with modern circuitry. This analog meter allows the
trained operator to determine much more from the needle movement than just a MΩ reading. Available in line,
battery or hand cranked models.
Other features include:
IR measurements to 2000MΩ
Four test voltages to 1kV
Guard terminal
Continuity and kΩ functions for troubleshooting
L
•
•
•
•
MJ159
L
MIT400/2 Series
MIT410/2
The MIT400/2 Series Insulation Testers offer outstanding performance and ease of use. Dual digital displays
show test results and test voltage or current simultaneously. The hands free, autoranging continuity function
ensures the accurate measurement of circuit conductors and bonding. An audible continuity alarm speeds
testing. These models offer improved test voltage accuracy, plus:
Insulation resistance measurements to 200GΩ; selectable test voltages to 1000V
Backlit LCD with dual digital and analog arc displays
Leakage current readout
Live circuit detection & protecton
PI/DAR and Timer functions (except MIT400/2)
IP54 & CAT IV 600V rating
L
•
•
•
•
•
•
The MIT series offers TRMS & DC Voltage measurements from 10mV to 600V. The MIT420/2 and MIT430/2 add
capacitance (100pf to 10uF), and test result storage/recall. MIT430/2 has Bluetooth for wireless data transfer
(including download software). All models except the MIT400/2 include frequency measurement (15-400Hz).
Every unit comes with carrying case, test leads, and battery. All models except the MIT400/2 also include a
remote switch probe for “hands free” testing.
MIT310
MIT300 Series
The new MIT300 Series features a large display and hands-free operation. The tough, rubber armored case is
designed for rough handling and weatherproof to IP54. A rigid cover folds up to protect the front panel when not
in use. Intelligent safety features include:
• Safety Interlock – prevents unsafe connection of test leads
• Safe contact detectors – the tester will remain safe and not be damaged if
connected to a live circuit while on continuity setting.
• Live voltage warning – alerts when circuit voltage is >25V.
• Safety lockout – inhibits test when circuit voltage is >50V.
• Continuity check – prevents a continuity test on a live circuit.
Each model includes a 200mA continuity test function and continuity
buzzer. All models except the MIT300 measure DCV & ACV (50/60Hz) to
600V. The MIT330 adds memory for storing 1000 test results and a USB
interface. The MIT310A has an analog meter display for those who prefer
a moving needle.
ORDERING INFORMATION
Model N o.
Tes t Volt age (V dc)
MJ159
100, 250, 500, 1000
MJ559
100, 250, 500, 1000
MIT400/2
250, 500, 1000
Insulation
Resis tance
0 to 2000 MΩ
0 to 2000 MΩ
0.01 MΩ to 200 GΩ
Resis tance
Range
0 to 5000 Ω
0 to 5000 Ω
0.01 Ω to 999 kΩ
ME/MIT410/2
MIT410/2
0.01 MΩ to 200 GΩ
0.01 Ω to 999 kΩ
ME/MIT420/2
MIT420/2
0.01 MΩ to 200 GΩ
0.01 Ω to 999 kΩ
ME/MIT430/2
MIT430/2
0.01 MΩ to 200 GΩ
0.01 Ω to 999 kΩ
ME/MIT300
ME/MIT310
ME/MIT310A
ME/MIT320
ME/MIT330
MIT300
MIT310
MIT310A
MIT320
MIT330
10 kΩ – 999 MΩ
10kΩ –
999 MΩ
10 kΩ – 999 MΩ
with limit alarm
–
–
10 Ω – 2 kΩ
0.01 – 99.9 Ω
10 Ω – 999 kΩ
50, 100,
250, 500, 1000
50, 100, 250, 500,
1000, variable
50, 100, 250, 500,
1000, variable
250, 500
250,
500, 1000
250,
500, 1000
Display
Analog
Analog
Analog/
Dual Digital
Analog/
Dual Digital
Analog/
Dual Digital
Analog/
Dual Digital
Digital/Analog
Digital/Analog
Analog
Digital/Analog
w/backlight
Power Sour ce
Hand-Cranked
Line or Rech. Batt.
Alkaline or
Rechargeable
NIMH Battery
(6 x AA)
Alkaline or
Rechargeable
NICD/NIMH
Battery
(8 x AA)
156
TEST
EQUIPMENT
Cat alog N o.
ME/212159
ME/212559
ME/MIT400/2
AEMC Megohmmeters
1000V Digital/Analog Megohmmeter Models 1050 & 1060
®
• True Megohmmeter
• Test voltage combinations of 50V, 100V, 250V,
500V and 1000V
• Insulation measurements to 4000GΩ (4TΩ)
• Direct measurement of DAR and PI values
• Direct measurement of sample Capacitance
• Display of test voltage and run time
• Programmable test run times and PI times
• Smooth and Alarm functions
• Automatic test inhibition (if live sample >25V)
• Automatic discharge after use with
voltage display
• Large dual display with time, voltage
and measurement
L 1060
• Bright blue electrolumenescent backlight
• Battery powered (Model 1050)
• Auto power-down when not in use
• Remote operation with optional test probe
• Rugged dual wall field case with detachable lead/accessory pouch
• EN 61010-1, 600V Cat III, IEC 61557 and CE rated
5000V Digital/Analog Megohmmeter Models 5050, 5060 & 5070
• True Megohmmeter ®
• Test voltage combinations of 500V, 1000V,
2500V and 5000V
• Insulation measurements from 30kΩ to
10,000GΩ (10TΩ)
• Selectable and programmable test voltage
(40 to 5100V)
• Automatic calculation of DAR, PI and DD ratios
• Direct measurement and display of Capacitance
and Leakage Current
• Display resistance, test voltage and run time
• Programmable test run times and PI ratio times
• Smooth and Alarm functions
L 5070
• Automatic test inhibition (if live sample >25V)
• Automatic discharge and display of discharge voltage
• Large dual display with time, voltage and
measurements shown (Models 5050 and 5060)
• Graphic and digital display of test voltage,
resistance and more (Model 5070)
• Bright blue electroluminescent backlight
• Programmable test voltage lock-out
DataView is included with the Models
• Programmable alarm setting
1060, 5060 and 5070
• Auto power-down when not in use
DataView® Software for
Models 1060, 5060 & 5070
• AC or DC powered with rechargeable
NiMH batteries
• Configure all functions and run
tests from your PC
• Rugged, weatherproof field case
• Retrieve and display data in real time
• Designed and built to IEC safety standards • Retrieve data from memory in real time
• Display plots & print reports
• EN 61010-1, 1000V Cat. III
®
Model 1060 includes the following additional features:
• AC rechargeable NiMH batteries
• RS-232 interface for direct printing of results (serial output)
• 128k memory to store measurements in specific files
• Remote operation of megohmmeter through PC
• Includes DataView ® software to configure instrument and
generate reports
ORDERING INFORMATION
AE/2130.01
AE/2130.03
AE/2130.20
AE/2130.21
AEMC Flexible Current Probe
L
TEST
EQUIPMENT
AE/2130.30
Megohmmeter Model 1050 (Digital, with Analog Bargraph, Backlight, Alarm, Timer, 50V, 100V, 250V, 500V, 1000V,
Auto DAR/PI, Res., Continuity)
Megohmmeter Model 1060 (Digital, with Analog Bargraph, Alarm, Timer, 50V, 100V, 250V, 500V, 1000V, Auto DAR/PI,
Res., Continuity, RS-232 with DataView® software, 128kB Memory)
Megohmmeter Model 5050 (Digital, with Analog Bargraph, Backlight, Alarm, Timer, 500V, 1000V, 2500V, 5000V, Auto
DAR/PI/DD)
Megohmmeter Model 5060 (Digital, with Analog Bargraph, Backlight, Alarm, Timer, 500V, 1000V, 2500V, 5000V, Auto
DAR/PI/DD, RS-232 w/DataView ® software)
Megohmmeter Model 5070 (Graphical, Analog Bargraph, Backlight, Alarm, Timer, 500V, 1000V, 2500V, 5000V, Ramp,
Auto DAR/PI/DD, RS-232 w/DataView ® software)
24-3001
• 24" flexible sensor fits around conductors up to 7.6" in diameter
• Reads Amps directly on DMM or Scope
• mV output directly proportional to AC current (10mV/A on 300A range and 1mV/A
on 3000A range)
• Accuracy 1% of Reading ± 500mA
• 4% influence of conductor position in jaw
• 300 hour battery life
• EN 61010, 1000V Cat. III
ORDERING INFORMATION
AE/2120.81
AE/2118.46
157
FlexProbe® Model 24-3001 (300/3000A, 24", 10mV/A/1mV/A, with lead)
Banana (Female) – BNC (Male) Adapter (XM-BB) for use with scopes
AEMC Megohmmeters
Digital/Analog Megohmmeters
1040
&
1045
Analog Megohmmeters
1015
1005
For motors, cables, switchgear and
general applications
Ideal for acceptance testing and preventive maintenance
•
•
•
•
•
•
•
•
•
•
•
1000V Megohmmeter
Hand-Cranked Megohmmeters
• True Megohmmeter ®
• Test voltages of 250V, 500V and
1000V
• Insulation measurements to
200MΩ and 5000MΩ
• LED indicates constant voltage
output and proper cranked speed
• Automatic discharge when
measurement is finished
• Auto-Ranging with dual scale
operation for better sensitivity and
easier readings
• Voltage display prior to, during
and at end of test
• Compact self-contained package;
folding crank
• Large direct-reading scale
• CAT III 300V rating
6527
• Test voltage combinations of 250V, 500V
and 1000V
• Insulation measurements to 4000MΩ
• Resistance measurements to 400kΩ
• Continuity meter, up to 200mA test current
• Voltmeter measures to 600VAC/1000VDC
• Large, dual, backlit digital display
• Auto HOLD function to freeze readings
• TEST LOCK feature for time sensitive
measurements up to 15 minutes
• Automatic discharge after insulation test
• Auto power off
• CAT IV 600V rating
• Supplied with a soft carrying case and
test leads
Compact and lightweight
Test voltage to 500V (Model 1005) or 1000V (Model 1015)
Insulation measurements to 1000MΩ
600VAC voltage measurement range (safety check)
0 to 10Ω+ and 0 to 10Ω - continuity ranges
Continuity measurements with 200mA test current
Resistance range to 1000Ω (Model 1015)
Push button for battery check
Large, direct-reading, colored scale
Rugged construction for heavy duty field use
Includes test leads, shockproof rubber housing & soft carrying case
TEST
EQUIPMENT
• True Megohmmeter ®
• Test voltage combinations of 250V, 500V and 1000V
• Insulation measurements to 2000MΩ (2GΩ)
• Automatic test inhibition (if live sample >25V)
• Automatic discharge for operator safety
• Multi-line 4000-count backlit digital display with analog bargraph
• Resistance measurements to 400kΩ
• Continuity with 200mA test current
• Timer function for easy DAR and PI (Model 1045)
• Over-molded slip-proof holster for rugged field use
• EN 61010-1, 300V Cat. II, EN 61557 and CE rated
• Supplied with a soft carrying case
6501
ORDERING INFORMATION
AE/2116.92
AE/2116.93
AE/2117.30
AE/2117.31
AE/2126.53
AE/2126.51
AE/2126.52
AE/1402.01
AE/1403.01
Megohmmeter Model 1040 (Digital, with Analog Bargraph, Alarm, Backlight, 500V, 1000V, 400kΩ, Continuity)
Megohmmeter Model 1045 (Digital, with Analog Bargraph, Alarm, Timer, Backlight, 250V, 500V, 1000V, 400kΩ, Continuity)
Megohmmeter Field Kit, Model 1040
Megohmmeter Field Kit, Model 1045
Megohmmeter Model 6527 (Digital, 250V, 500V, 1000V, 400kΩ, 600VAC/1000VDC measure)
Megohmmeter Model 6501 (Hand-cranked, 500V, 500kΩ, Continuity)
Megohmmeter Model 6503 (Hand-cranked, 250V, 500V, 1000V)
Megohmmeter Model 1005 (Analog, 500V, Continuity)
Megohmmeter Model 1015 (Analog, 500/1000V, Resistance, Continuity)
158
AEMC Ground Resistance Testers
Digital Ground Resistance Tester
Models 4620 & 4630
• Measures soil resistivity (4-Point) method
• Measures ground resistance (2- and
3-Point) Fall-of-Potential method
• Step voltage tests and touch potential
measurements
• Auto-Ranging: automatically selects the
optimum range
• Designed to reject high levels of noise
and interference
• Extremely simple to operate:
connect – press – read
• LED on faceplate informs operator of high
input noise, high auxiliary rod resistance and
fault connections
• Large easy-to-read backlit display
• Battery powered (Model 4620)
• AC powered with rechargeable NiMH batteries
(Model 4630)
• Rugged dustproof and rainproof field case
• Can also be used for continuity tests
on bonding
• Color-coded terminals
Clamp-On Ground Resistance Tester
Models 6416 & 6417
L 6416
L 4630
Also available as full kits
• Ground voltage indication (warns of possible
unsafe conditions)
• Large multi-function bright yellow organic
LED display (OLED)
• Selectable test frequency improves
accuracy in inductive environments
• Large jaw with 35mm clamping diameter
• Storage of up to 300 measurements, W &
A with time-stamp (Model 6417: up to
2000 measurements stored)
• View stored measurements on the OLED
display (also on PC or Android phone via
Bluetooth for Model 6417)
• Alarm function with adjustable set point &
buzzer for quick field checks of volts, amps
and ohms
• Alarm settings and stored memory
information saved during shutdown
• Includes DataView® software for data
storage, real-time display, analysis, report
generation and system configuration
(Model 6417)
• Noise icon and buzzer alert user to presence
of dangerous voltage and current levels
• Designed to EN 61010-1, 600V CAT IV
safety standards
• 2- and 4-Wire Bond Resistance/Continuity measurement
• 3-Point Fall-of-Potential measurement with manual/automatic frequency selection
• 4-Point soil resistivity measurement with automatic calculation of Rho & user selection
of Wenner or Schlumberger method
• 3-Point earth coupling measurement
• Frequency scan 40-513Hz for testing in electrically noisy environments
• Selectable test voltage of 16 or 32V up to 250mA of test current
• Automatic recognition of all electrode connections & resistance
• Stores up to 512 complete test results
• Optically isolated USB communication
• Rechargeable NiMH batteries from wall charger or vehicle power
• Rugged dustproof and rainproof field case
• Includes DataView® software for remote operation, data storage, real-time display,
analysis, report generation & system configuration
Model 6742 adds:
• Manual and automatic frequency scan to 5078Hz
• Measures Ground Resistance using the 2 clamp method (selective ground testing)
• Measures Ground Impedance up to 5kHz to test lightning strike protection
Tester includes meter, NiMH
batteries, optical USB cable,
DataView® software, external
battery charger, power cord,
user manual.
Kit includes Tester, test leads,
30 ft ground lead (green),
auxiliary ground electrodes,
spaded lugs, 100 ft tape
measure, ground tester
workbook CD, carrying bag
for meter, carrying bag for kit.
L
TEST
EQUIPMENT
Multi-Function Ground Resistance Tester Models 6470B & 6472
6470B
ORDERING INFORMATION
AE/2130.43
AE/2130.44
AE/2135.20
AE/2135.23
300’
AE/2141.01
/100’ leads
AE/2141.02
AE/2135.01
Ground Resistance Tester Model 4620
(4-Point, Digital, Battery Powered)
Ground Resistance Tester Model 4630
(4-Point, Digital, Rechargeable Battery)
Model 4620 Kit with 300/100 ft leads
Model 4630 Kit with 300/100 ft leads
Ground Resistance Tester Model 6416 (Clamp-On)
Ground Resistance Tester Model 6417
(Clamp-On with Bluetooth)
Ground Resistance Tester Model 6470B
AE/2135.03 Ground Resistance Tester Model 6470B 4-point Kit – 300/100 ft leads
AE/2135.04 Ground Resistance Tester Model 6470B 4-point Kit – 500/100 ft leads
AE/2135.51 Ground Resistance Tester Model 6472
AE/2135.53 Ground Resistance Tester Model 6472 4-point Kit – 300/100 ft leads
AE/2135.54 Ground Resistance Tester Model 6472 4-point Kit – 500/100 ft leads
AE/2135.71* AC Current Probe Model MN82 for use with Model 6472
AE/2135.72* AC Current Probe Model SR182 for use with Model 6472
*2 probes required for two clamp testing method.
159
Megger® Ground Resistance Testers
Three-Terminal Ground Resistance Testers
Four-Terminal Ground Resistance Testers
®
BIDDLE Model 250260 is the tried and proven analog tester.
It is a simple, three-terminal model that will tolerate 2V peakto-peak voltage interference.
Addition of a fourth terminal permits soil resistivity testing as well
as more precise resistance (installed ground) measurements.
The new DET4TD2 offers the same features as the DET3TD, but
with 4-terminal capability and a 20kΩ upper resistance limit. The
DET4TC2 increases this to 200kΩ. The DET4TCR2 has rechargeable batteries that can be charged from the AC mains or a vehicle
battery (with optional adapter). The DET4TC2 and DET4TCR2 offer
4 test frequencies for testing in noisy environments. Both models
can be ordered with clamps to perform the stakeless test method,
like a clamp style earth tester. A backlit LCD provides improved visibility in dark locations.
The MEGGER® DET3TD is a digital tester with an expanded
resistance range and selectable 25/50V test voltage. It rejects
noise up to 40V p-p and measures earth voltages up to 100V.
The DET3TC adds an ART (Attached Rod Technique) resistance
measurement and earth current measurements from 0.5mA to
19.9A with the optional current clamp.
For testing in extreme electrical environments, the DET2/2 offers
full autoranging, 0.001Ω resolution, adjustable test frequency and
additional interference filtering.
250260
L
DET4TCR2+Clamps
L
L
All DET3 and DET4 models are CAT IV 100V and IP54 rated. Test
leads and carrying case are included.
DET2/2
DET3TC
DET4TCR2
L
L
NEW
ORDERING INFORMATION
Measur ement
Resis tance
250260
2/3 Term.
DET2/2
Volt age
Gnd Cur rent
Power Sour ce
Display
Tes t Leads
0.5 - 500Ω
Battery
Analog
250560
2/3/4 Term.
0.010Ω - 20kΩ
Rechargeable
Battery
Digital
250581
DET3TD
2/3 Term.
0.01 - 2000Ω
0 - 100V
Battery
Digital
included
DET3TC
2/3 Term. + ART*
0.01 - 2000Ω
0 - 100V
Battery
Digital
included
0.5mA - 19.9A*
DET4TD2
2/3/4 Term.
0.01Ω - 20kΩ
0 - 100V
Battery
Digital
included
DET4TC2
2/3/4 Term.
0.01Ω - 200kΩ
0 - 100V
Battery
Digital
included
2/3/4 Term. + stakeless
0.01Ω - 200kΩ
0 - 100V
0.5mA - 19.9A
Battery
Digital
included
DET4TCR2
2/3/4 Term.
0.01Ω - 200kΩ
0 - 100V
Digital
included
DET4TCR2
+Clamps
2/3/4 Term. + stakeless
0.01Ω - 200kΩ
0 - 100V
0.5mA - 19.9A
Rechargeable
Battery
DET4TC2+Clamps
* Attached Rod Technique (ART) requires optional current measuring clamp.
160
TEST
EQUIPMENT
Model N o.
Megger® Clamp-on Testers
Hioki Battery Testers
NEW
Ground Resistance Testers
• Easy, fast clamp-on operation – No
rods or cables needed
• Measure ground resistance from
0.05Ω to 1500Ω
• Measure ground leakage or phase
current from 0.5mA to 35A
• Auto ranging with high & low alarms
• Automatic self calibration
• Data storage & USB interface
DET24C
TEST
EQUIPMENT
FEATURES
• Backlit LCD display can be read in bright sunlight.
• Large 39 x 55mm jaw with 39mm (1.5") opening.
• Noise filter for stable readings in noisy environments.
• Hold function for difficult to reach installations.
• 24 hour battery life with auto-off to save on battery power.
• Two alarms with adjustable threshold & audible indication.
• Stores 2000 test results (DET24C).
• Calibration check loop insures proper operation.
• CAT IV 600V safety rating.
Accuracy
±1.5% ± 0.05Ω
±1.5% ± 0.1Ω
±2% ± 0.5Ω
±5% ± 1Ω
±6% ± 5Ω
±10% ± 10Ω
±20%
±35%
Range
Resolution
0.5 - 0.99mA
0.01mA
1.00 - 9.99mA 0.01mA
10.0- 99.9mA 0.1mA
100 - 999mA
1mA
1.00 - 9.99A
0.01A
0.1A
10.0 - 35.0A
TRMS reading, CF<5, 50-400Hz
Basic Accuracy 2% @ 50/60Hz
Model DET24C includes USB interface, IrDA dongle and software for
downloading test data. Both models include batteries, carrying case,
carrying strap & calibration loop.
ME/DET14C
ME/DET24C
161
• Test without disconnecting the batteries
• Three level indication: Pass, Warning, Fail
• Audible beeper (3555)
• PC Interface & software (3554)
Get an instantaneous check of battery condition based
on internal resistance and voltage.
APPLICATIONS
• Measure resistance and continuity of grounding loops around pads,
poles and buildings.
• Check multi-grounded systems without disconnecting the ground
rod/stake under test.
• Measure leakage current flowing to ground or circulating in
ground systems.
• Use on cell towers, RF transmitters and telecom sites.
• Inspect and verify lightning protection systems.
• Test consumer installations, including pools, spas, etc.
Range
Resolution
0.05 - 0.99Ω
0.01Ω
1.00 - 9.99Ω
0.01Ω
10.0 - 99.9Ω
0.1Ω
100.0 - 199.9Ω 0.1Ω
200 - 400Ω
1Ω
400 - 600Ω
1Ω
600 - 1200Ω
10Ω
1200 - 1500Ω 10Ω
3554
ORDERING INFORMATION
Digital Earth Test Clamp-on Meter
Digital Earth Test Clamp-on Meter with USB
Model 3554 for medium and high capacity lead-acid batteries.
Model 3555 for compact storage batteries used in portable
telephones and similar applications.
SPECIFICATIONS
3554
Measurement Ranges:
Ohms:
# Ranges
Best resolution
Accuracy
Test Current
DC Volts
Best resolution
Accuracy
Temperature
Resolution
Test Frequency
Max. Input
Comparator
# Limit Sets
Data Memory
Alert
Batteries
Life
PC Interface
Operating Temp.
Dimensions
3555
3μΩ-3Ω
300μΩ-30Ω
4
3
1μΩ
100μΩ
0.8% rdg +6d
0.8% rdg +6d
150mA-1.5mA
5mA-50μA
±6V, ±60V
±3V, ±30V
1mV
1mV
0.08% rdg +6d
0.1% rdg +6d
-10 to +60°C
-0.1°C
-1kHz
1kHz
60V DC
50V DC
Hi & low ohm limit, low volt limit (both models)
200 stored
10 stored
4800 data/limit sets
-LCD icon
LED & Beeper
9 x AA
6 x AA
up to 10 hrs
up to 18 hrs
USB
-0-40°C, <80% RH non-condensing
7.7 x 5.1 x 2.2" (196x130x55mm)
SUPPLIED ACCESSORIES
3554
3555
Pin-type test leads, USB cable, data management sofware,
carrying case, zero adjust board, batteries, spare fuse
Pin-type test leads, batteries.
ORDERING INFORMATION
HK/3554
HK/3555
HK/9382
HK/9453
HK/9466
Battery Tester (lead-acid batteries)
Battery Tester (portable batteries)
Carry case for 3555
4-terminal lead set
Remote Control Switch for 3554
Megger® High-Pot Testers
Production Line High-Pot Testers
230415
L
BIDDLE® High-Pot Testers are designed for ease of operation and readily adapt to development,
maintenance or production testing. These instruments are supplied with 4-ft removable probes.
Available in one AC/DC and two AC models; the AC units feature a front-panel, NEMA-5-15R
three-prong output receptacle.
The BIDDLE high-pot testers are packed with features for safety and convenience, including:
Ground continuity check of 3-wire devices with high voltage interlock
Visual and audible alarms
Leakage current adjustable on front-panel from 0.3 to 12.3 mA
One-second or continuous testing
Automatic failure shutdown
Recessed high-voltage connections
Catalog No.
Model
ME/230315
ME/230415
ME/230425
AC
AC
AC/DC
Applied Test
Voltage
0–3 kV ac
0–4 kV ac
0–4 kV ac
0–5 kV dc
Adjustable Leakage
Current Trip Level
0.3 to 12 mA
0.3 to 12 mA
AC: 0.3 to 12 mA
DC: 0.43 to 17 mA
Megger® Digital Low Resistance Ohmmeters
Range
1.9999 mΩ
19.999 mΩ
199.99 mΩ
1999.9 mΩ
19.999 Ω
199.99 Ω
1999.9 Ω
Resolution
0.1µΩ
1 µΩ
10 µΩ
100 µΩ
1 mΩ
10 mΩ
100 mΩ
Current
10 A
1A
100 mA
10 mA
1 mA
0.1 mA
0.1 mA
Test Leads & Battery Charger Included
Resolution
10 mΩ
100 mΩ
0.1µΩ
1 µΩ
10 µΩ
100 µΩ
1 mΩ
10 mΩ
100 mΩ
DLRO10HD
Current
10 A
1A
10A
1A
100 mA
10 mA
1 mA
0.1 mA
0.1 mA
DLRO with LED display
DLRO with LCD display
Heavy Duty DLRO (LCD display)
DLRO 200
• Test currents from 10A to 200A DC
• Filtered DC output eliminates
magnetic transients
• 0.1µΩ best resolution
• Full QWERTY keyboard
• On board memory for up to
300 test results and notes
• RS232 port to download stored
results or for real time output
to a printer
Measurement Range: 0.1µΩ to 999.9mΩ
Test Modes:
Normal, Continuous, Auto. Use
continuous mode for long duration tests,
Auto mode for rapid sequential testing.
Test Time:
10 seconds
Display:
Large backlit LCD
Dimensions:
16.4" x 9.9" x 10.7"
(410x250x270mm)
Weight:
32 lbs (14.5kg)
Power:
100-130VAC, 50/60Hz
TEST
EQUIPMENT
ME/DLRO-10
ME/DLRO-10X
ME/DLRO10HD
Range
250.00 mΩ
2500.0 mΩ
2500.0 µΩ
25.000 mΩ
250.00 mΩ
2500.0 mΩ
25.000 Ω
250.00 Ω
2500.0 Ω
NEW
L
DLRO–10
DLRO10HD
• Accurate results in under three seconds
• Delivers up to 10A into 250mΩ (25W)
• Auto current reversal cancels standing emfs
• Operates from rechargeable battery or line power
• Fuse protected to 600 V
• Input protected to 600V
• NiMH battery reduces weight
• Heavy duty IP65 case
• 250 mW power limit avoids heating the test sample • 5 test modes, including auto-start on connection
• Autoranging with high/low limits (DLRO 10X)
• Simple to use rotary switches
L
•
•
•
•
•
•
DLRO 200
Supplied with 16 ft. (5m) test leads and download software.
A variety of C-clamp, Kelvin clips, fixed point and spring point leads are available in various lengths.
ME/DLRO200-115E
High Current Digital Low Resistance Ohmmeter
162
•
•
•
•
•
•
•
Battery operated
Auto range: 1 μΩ to 1000 mΩ
Test current up to 220 Amps
Safe test – DualGround™
Stores up to 190 test records
Bluetooth® PC communication
Ultra capacitor technology (patent
pending)
MOM2
The MOM2 Micro-ohmmeter is a lightweight, handheld unit
designed to deliver up to 220 Amps and measure the resistance of
circuit breaker contacts, bus-bar joints and other high-current links.
Measurements are made using the DualGround™ method, where
the test object is grounded on both sides throughout the test for a
safer, faster and easier workflow. The conventional test method,
with one side grounded, is also supported (optional cable kit
required).
Megger® High Current Loop Tester
•
•
•
•
•
NEW
Megger® Handheld
Micro-ohmmeter
SPECIFICATIONS
Voltage Measure:
Frequency:
Loop Resistance:
Test Current:
Operating Temp.:
Power:
Dimensions:
• Measures the height of up to six
overhead cables
• Dramatically reduces measuring time
• No physical connection to cables or wires
• Designed for portability & ease-of-use
• Readout in feet/inches or meters
TEST
EQUIPMENT
162a
0-550V (400V @ 16 Hz); Accuracy 5% ±2V
Supply frequency indicated upon connection (16, 50/60,
400 Hz). Test frequency automatically set
0-19.99Ω and 0-199.9Ω; Accuracy 5% ±5d
3-27A on 20Ω range, 0.3-2.7A on 200Ω range
-10ºC to 60°C, < 90% RH @ 40°C
Eight standard AA alkaline batteries
8"H x 5.8"W x 3"D (203 x 148 x 78 mm)
Megger® Cable Height Meter
Application:
Resistance Ranges:
Resolution:
Transport case, charger, rubber holster, carrying strap, belt clip, PC software included.
LT300
The LT300 offers high current loop testing over a wide range of frequencies and supply voltages with simple, fast, two wire operation.
SPECIFICATIONS
High-voltage substations & industrial environments
Autoranging from 0 - 1000 mΩ
0 – 999 μΩ
1 μΩ
1.0 – 9.99 mΩ
0.01 mΩ
10.0 – 99.9 mΩ
0.1 mΩ
100 – 1000 mΩ
1 mΩ
Accuracy:
0 – 1999 μΩ
±1 % of reading ±1 digit
2 – 1000 mΩ
±2 % of reading ±1 digit
Pass / Fail:
Settable from 1 μΩ to 1999 mΩ
Output Current:
Selectable minimum of 50 A or 100 A
(100A valid at resistance <2mΩ)
Output Voltage:
2.5 V DC max
Output Duration:
Selectable: 0.1 s, 0.6 s, 3 s
Recovery Time:
10-130 sec
Voltage In:
±3 V DC
Trigger In:
Threshold 8 V DC
DC Power In:
12 – 24 V DC, 2 A max
Operating Temp.:*
-20ºC to +50°C (-4°F to +122°F)
Relative Humidity:
5%-95%, non condensing
Battery:
Five AA, 2700 mAh NiMH cells
Capacity:
Typ. 2200 measurements at 50 A and 0.1 s
from fully charged batteries
Battery Charger:
100-250 V AC, 50/60 Hz, 60 W
Recharge Time:
< 12 hr; < 3 hr typical at 25°C
Real-time Clock:
Battery life >10 years
Audible Feedback: Different buzzer sounds
User Presets:
3
Data Logger:
Label. Timestamp, I max, I min, I Limit, Resistance,
Meas. time, P/F limit
Data Capacity:
190 measurements
Wireless:
Bluetooth headset & PC communication
Encapsulation:
IP54
Dimensions:
8.5"H x 3.6"W x 2.8"D, excl. binding posts
(217 x 92 x 72 mm)
Weight:
1.0 kg (2.2 lbs) instrument only
*Battery operation temperature 0ºC to +50° (32°F to +122°F)
*Battery charging temperature +10ºC to +40° (50°F to +104°F)
Single and 3 phase testing
16 Hz to 400 Hz operation
Simple 2 wire operation
CAT IV 300V applications
0.01Ω resolution on 20Ω range
CHM600
The CHM Series utilize ultrasonic techniques to determine the height of
up to six overhead cables and wires. The meter displays the height of
the lowest cable and the spacings between the next five cables.
SPECIFICATIONS
Min. Cable Size:
(@ 68º F)
Resolution:
Accuracy:
Power Source:
Operating Temp.:
Battery Life:
Dimensions:
CHM2000: 0.125" @ 7-32 ft, 0.5" @ 35 ft.
CHM600: 0.125" @ 10-32 ft, 0.5" @ 50 ft.
CHM600E: 0.5" @ 10-50 ft, 1" @ 75 ft..
1/4 in. (5 mm) if < 10 m
1/2 in. (10 mm) if > 10 m
Typically less than 0.5% error ±2 digits
9 volt alkaline battery (included)
14º F to 104º F (-10º C to 40º C),
reading compensated over the full range
> 50,000 measurements
3"H x 4"W x 8.5"D (70 x 100 x 205 mm)
ORDERING INFORMATION
ME/BD-59090
MOM2 Micro-ohmmeter with 2 x 1.3 m (4 ft) test cables
Kelvin probes (one with trig button)
ME/BD-59092 MOM2 Micro-ohmmeter with 1.3 m (4 ft) test cable red &
Kelvin clamp 3 m (10 ft) test cable black with Kelvin
clamp (Cat #GA-90001)
ME/GA-00384
15 meter Cable Kit
ME/LT300-EN-00 High Current Loop Tester with red/green leads & carry case
ME/LT300-EN-FS High Current Loop Tester with fused leads & carry case
ME/CHM2000
Telecom Cable Height Meter; 6 lines; 7-35 ft.
ME/659600
CHM600 Power Cable Height Meter, 6 lines; 10-50 ft.
ME/659600E
CHM600E Power Cable Height Meter, 6 lines; 10-75 ft.
Altek Process Calibrators
Milliamp Calibrator
• Source and Read 0-24mA
• Simulate 2-wire Transmitters
• Quik-Chek Pushbuttons
MILLIAMP CALIBRATOR SPECIFICATIONS
Ranges
Accuracy
Burden
Drive
Battery Life
Use the PocketCal 134-2 to simultaneously power and measure two-wire
transmitters up to 12V. Simulate the
transmitter in circuits from 3 to 45V.
0.00 to 24.00mA, -25.0 to 125.0% of 4 to 20mA
0.03mA
0.9V @4mA, 1.9V @24mA
700Ω @20mA with fresh batteries
40hr simulate, 20hr source from 9V batteries (supplied)
134-2
Loop Calibrator
• Source to 24mA, Read to 52mA
• Measure to ±99.9V DC
• Quickly Simulate 2-wire Transmitters
LOOP CALIBRATOR SPECIFICATIONS
Source/Simulate
Read
Accuracy
The versatile 334A will check,
calibrate and troubleshoot all the
signals in a 4-20mA process control
loop. Simultaneously power and
measure two-wire transmitters up to
27V. Simulate the transmitter in
circuits from 3 to 45V. Overload
protected to 135VAC.
Drive
Battery Life
334A
0.00 to 24.00mA, -25.0 to 125.0% of 4 to 20mA
0.00 to 52.00mA, -25.0 to 300.0% of 4 to 20mA
0-24mA: ±0.05% of reading ± 1 digit
Quik-Chek: ±0.03% of reading ± 0.01mA
1200Ω @20mA with fresh batteries
100hr simulate, 20hr source from
9V batteries (supplied)
MULTIFUNCTION CALIBRATOR SPECIFICATIONS
TEST
EQUIPMENT
820E
Multifunction Calibrator
FUNCTION
mA Source/Measure
mV
V
V (measure only)
VAC (measure only)
TC
RTD
Ohms
Frequency
Simulate Range
ma Compliance
Transmitter Drive
Battery Life
• Calibrate Milliamps, Volts
& Frequency
• Check Thermocouple & RTD Sensors
• Use in Place of a DMM for ACV & Ohms
• Simulate 2-Wire Transmitters
The deluxe Model 820E combines the functions
of the 111, 322-1, 334A and voltage calibration
in one compact unit. It also performs frequency
calibration and extended voltage measurements.
RANGE
0.00 to 24.00mA, -18.8 to 125.0% of 4 to 20mA
0.00 to 110.00mV DC (20mA max source/sink)
0.00 to 10.25V DC (20mA max source/sink)
0.0 to 200.0V DC
0.0 to 250.0V AC TRMS
J, K, T, E
100Ω Pt, 385 alpha (2mA max)
0 to 400.0Ω source, 0 to 1000.0Ω measure
1-1000 CPM, 1-1000 Hz, 0.01-10.00 kHz
3 to 45V
25V (max 1.9V burden at 24mA)
1200Ω @20mA typical, Power & Measure mode
50hr simulate, 20hr source (AA batteries supplied)
ACCURACY
±0.05% of FS ± 1d
±0.05% of FS ± 1d
±0.05% of FS ± 1d
±2% of FS ± 1d
±2% of FS ± 1d
±2% typical
±1°C
±0.06Ω
±0.05% of FS ± 1d
ORDERING INFORMATION
(Batteries & three year warranty included)
AL/134-2
PocketCal Milliamp Calibrator
AL/334A
Milliamp Loop Calibrator with Carrying Case
AL/820E
TechChek Multifunction Calibrator with Carrying Case
AL/3331E
Carrying Case with Belt Clip for 134-2
163
Altek Temperature Calibrators
RTD Calibrators
• Source and
Read Pt RTDs
• 8 RTD Types Plus
Ohms (Model 211)
• 0.1° and 0.01Ω
Resolution
• °C/°F Display
• Easy Dial Setting
• Small and Lightweight
L
111
The Model 111 simulates and measures
3-wire, 100Ω Platinum RTDs over the full
industrial temperature range. The Model 211
handles multiple RTD types in either 3 or 4 wire
configurations, plus extended ohms range.
SPECIFICATIONS
MODEL 111
RTD Type
Accuracy
100Ω Pt (DIN/IEC/JIS), 385 alpha
-200.0 to 200.0°C (-328.0 to 212.0°F) ±0.5°C (±0.9°F)
200.0 to 700.0°C (212.0 to 750.0°F)
±0.6°C (±1.0°F)
700.0 to 850.0°C (750.0 to 1562.0°F) ±0.7°C (±1.2°F)
MODEL 211
RTD Type
Pt100 (DIN/IEC/JIS)
Pt100 (JIS 1981)
Pt100 (Burns)
Pt100 (US lab)
Pt1000 (HVAC)
Cu10 (Minco)
Ni120
Ni110
Accuracy (typical)
MODEL 111 & 211
Ohms
Excitation Current
Temperature Drift
Battery Life
Size
Thermocouple Calibrators
• Source and
Read Modes
• 0.1° and 0.001mV
Resolution
• °C/°F Display
• Easy Dial Setting
• Small and
Lightweight
Simulate and measure the most popular
thermocouple types with the Model 322-1.
Use the Model 422 with 14 different types.
Three output memories for each TC type
facilitate repetitive testing. Each model accepts
miniature thermocouple connectors and direct
thermocouple wires.
Range
-200.0 to 850.0°C (-328.0 to 1562.0°F)
-200.0 to 648.9°C (-328.0 to 1200.0°F)
-195.6 to 648.9°C (-320.0 to 1200.0°F)
-200.0 to 862.0°C (-328.0 to 1584.0°F)
-184 to 275°C (-300 to 527°F)
-200 to 260°C (-328 to 500°F)
-80.0 to 273.0°C (-112.0 to 524.0°F)
-106.7 to 315.6°C (-160.0 to 600.0°F)
±0.15°C (±0.25°F)
±0.10°C (±0.2°F)
±1.1°C (±2.0°F)
0.00 to 410.00 ±0.2Ω accuracy
0.0 to 2010.0 ±0.5Ω accuracy (211 only)
0.09 to 5.80 mA source, 1mA read
<0.01%/°C change in ambient
Approx. 50 hrs from 9V alkaline battery (supplied)
5.2" x 2.6" x 2.5" (130x67x64 mm)
SPECIFICATIONS
Input/Output (322-1)
Input/Output (422)
Ranges
Accuracy
Cold Junction Effect
Battery Life
Size
Type J, K, T, E and mV
Type J, K, T, E, R, S, B, N, G, C, P, L, U, D and mV
J:
-210.0 to 1200.0°C (-346.0 to 2192.0°F)
K:
-230.0 to 1371.1°C (-382.0 to 2500.0°F)
T:
-260.0 to 400.0°C (-436.0 to 752.0°F)
E:
-240.0 to 1000.0°C (-400.0 to 1832.0°F)
R, S: -18.3 to 1767.8°C (-1.0 to 3214.0°F)
B:
315.6 to 1820.0°C (600.0 to 3308.0°F)
N:
-230.0 to 1300.0°C (-382.0 to 2372.0°F)
G:
100.0 to 2320.0°C (212.0 to 4208.0°F)
C, D: -1.1 to 2320.0°C (30.0 to 4208.0°F)
P:
-217.8 to 1395.0°C (-360.0 to 2543.0°F)
mV: ±99.999mV
±(0.008% + 0.006mV), typically ±0.2°C or better
<0.05°/°C change in ambient
Approx. 40 hrs from 9V alkaline battery (supplied)
5.2" x 2.6" x 2.5" (130x67x64 mm)
ORDERING INFORMATION
(Batteries, carrying case and three year warranty included)
AL/111
RTD Calibrator (100Ω Pt, 385)
AL/211
RTD Calibrator (8 types)
AL/322-1
Thermocouple Calibrator (type J, K, T, E)
AL/422
Thermocouple Calibrator (14 types)
164
TEST
EQUIPMENT
L
322-1
Alpha
3850
3916
3902
3926
3750
4274
6720
5801
Pt100
Pt1000, Ni
Cu10
Yokogawa Calibrators
CA11E Voltage/Current Calibrator
CA12E Temperature Calibrator
• Source and Measure
Voltage and Current
• 4-20mA and 1-5V DC
Step-up/down Function
• 20mA SINK Function
• Sweep Function
• 0.05% Basic Accuracy
•
•
•
•
Simulate Thermocouples and RTDs
Multi-range RTD Thermometer
°C/°F Selection
Built-in Sensor for Reference
Junction Compensation
• 0.05% Basic Accuracy
• Binding Post Terminal Adapter
SPECIFICATIONS
SPECIFICATIONS
Sour c e / M e a s u r e m e n t F u n c t i o n s
Sour c e / M e a s u r e F u n c t i o n s
R ang e
30V
10V
1-5V (source only)
1V
100mV
20mA
4-20mA (source only)
20mA SINK (source only)
Selection
Type K
Type E
Type J
Type T
Type N
Type R, Type S
Type B
Type L
Type U
RTD Pt100 (3 wire)
100mV
400Ω
Span
0 to 30.00V DC
0 to 11.000V DC
1/2/3/4/5V DC
0 to 1.1000V DC
0 to 110.00mV DC
0 to 24.000mA DC
4/8/12/16/20mA
0.1 to 24.000mA
CA71/SP1
Multi-function
Calibrator
• Simultaneous Source &
Measure Capability
• Separate Source &
Measure Switches for
Easy Setup
• Autostep, Sweep & Memory Functions
• 0.025% Measure Accuracy (DCV)
Each CA71/SP1 includes: 120VAC adapter, source & measure cables, terminal adaptor for temperature measurements, input fuse, magnetic instrument
case, accessory case for input cables, carrying case, 9 pin RS232 communications cable & data logging software.
TEST
EQUIPMENT
SPECIFICATIONS
S O U R CE
FUN C T I O N S
DCV
DCA
mA sink
Resistance
RTD
TC
TC
Frequency
Pulse
MEASURE
FUN C T I O N S
DCV
DCA
Resistance
ACV
RTD
TC
TC
Frequency
Pulse
165
RAN GES
100mV/1V/10V/30V
20mA/4-20mA
20mA
400Ω
Pt100 (-200 to +850°C)
JKTELUN
RSB
500/1000/10kHz
99999 cycles
RAN GES
100mV/1V/10V/100V
20mA/4-20mA
400Ω
1/10/100/300V
Pt100 (-200 to +850°C)
JKTELUN
RSB
100/1000/10kHz
99999 counts/min, /hr
BES T
RESOL UTION
10mV
1µA
1µA
0.01Ω
0.1°C
0.1°C
1°C
0.2Hz
1
BES T
RESOL UTION
10mV
1mA
0.01Ω
1mV
0.1°C
0.1°C
1°C
0.01Hz
1
BES T
ACCURA CY
0.02%+15µV
0.025%+3µA
0.05%+3µA
0.02%+0.1Ω
0.025%+0.3°C
0.02%+0.5°C
0.02%+1.5°C
0.2Hz
-BES T
ACCURA CY
0.025%+20µV
0.025%+4µA
0.05%+0.1Ω
0.5%+5 digits
0.05%+0.6°C
0.05%+1.5°C
0.05%+2°C
2 digits
--
Sour c e / M e a s u r e
-200.0 to 1372.0°C
-328 to 2498°F
-200.0 to 1000.0°C
-328 to 1832°F
-200.0 to 1200.0°C
-328 to 2192°F
-200.0 to 400.0° C
-328 to 752°F
-200.0 to 1300.0°C
-328 to 2372°F
0 to 1768°C
32 to 3214°F
600 to 1800°C
1112 to 3272°F
-200 to 900°C
-328 to 1652°F
-200 to 400°C
-328 to 752°F
-200.0 to 850.0°C
-328 to 1562°F
-10.00 to 110.00mV
0 to 400.0Ω
CA150/SP1
Multi-function Calibrator
• Simultaneous Source & Measure Capability
• Large LCD Display
• Step, Linear & Programmed Sweeps
• Loop Power Supply
• DC Voltage and Current Generation
• Settings and Data Memory
• 0.02% Measure Accuracy (DCV)
Each CA150/SP1 includes: 120VAC adapter, source & measure cables,
terminal adaptor for temperature measurements, input fuse, NiMH battery,
accessory case for input cables & carrying case
SPECIFICATIONS
S O U R CE
FUN C T I O N S
DCV
DCA
mA sink
Resistance
RTD
TC
TC
Frequency
Pulse
MEASURE
FUN C T I O N S
DCV
DCA
Resistance
RTD
TC
TC
Frequency
Pulse
RAN GES
100mV/1V/10V/30V
20mA
20mA
500/5k/50kΩ
Pt100 (-200 to +850°C)
JKTELUN
RSB
100/1000/10k/50kHz
1100 CPM
RAN GES
500mV/5V/35V
20mA/100mA
500/5k/50kΩ
Pt100 (-200 to +850°C)
JKTELUN
RSB
100/1000/10kHz
100000 CPM, CPH
BES T
RESOL UTION
1µV
1µA
1µA
0.01Ω
0.1°C
0.1°C
1°C
0.01Hz
0.1 CPM
BES T
RESOL UTION
10µV
1µA
0.01Ω
0.1°C
0.1°C
1°C
0.01Hz
1
BES T
ACCURA CY
0.02%+10µV
0.02%+3µA
0.025%+6µA
0.02%+1.5Ω
0.025%+0.3°C
0.02%+0.4°C
0.02%+1.2°C
0.05Hz
0.5 CPM
BES T
ACCURA CY
0.02%+50µV
0.025%+4µA
0.055%+0.075Ω
0.05%+0.6°C
0.05%+1.5°C
0.05%+2°C
2 digits
--
NEW
Yokogawa Process Calibrators
VOLTAGE/CURRENT
THERMOCOUPLE
• Measure & source
(simulate) 16 T/C types
• 0.5°C basic accuracy,
including internal
reference junction
• Step, ramp & sweep
• Dual display (° & mV or %)
• Source to 24mA, ±33V
• Measure to ±60mA, ±55V
• Step, ramp & sweep
• 24V loop power supply
• Simulate (sink) function
CA310
CA320
SPECIFICATIONS
Source:
0 to 24.000mA, <1kΩ load
0 to 550.00mV/5.5000V/±33.000V
Measure:
0 to ±24.000mA/±60.000mA;
0 to ±550.00mV/±5.5000V/
±33.000V/±55.000V
Simulate:
0 to 24.000mA, 5-28V external supply
Input R:
mA source: <10Ω
V measure: >1MΩ
Loop Supply: 24V ±1V (@24mA, comm R OFF)
24V ±6V (@20mA, comm R ON)
Accuracy:
0.015% +3 digit (+5 digits on volts)
Dimensions: 7.5" x 3.6" x 1.65" (192 x 90 x 42mm)
Includes test leads, batteries & carrying case. AC
adapter sold separately (P/N 94013).
ORDERING INFORMATION
YE/CA310
YE/CA320
YE/CA330
Volts & mA Calibrator
Thermocouple Calibrator
RTD Calibrator
RTD
• Source/Measure 16 RTD
types
• 0.3°C basic accuracy
• 2/3/4-wire
• Step, ramp & sweep
• Dual display (° & Ω or %)
SPECIFICATIONS
Type K
Type E
Type J
Type T
Type N
Type L
Type U
Type R, S
Type B
Type C
Type XK
Type A
Voltage:
Accuracy:
-200.0 to 1372.0°C
-250.0 to 1000.0°C
-210.0 to 1200.0°C
-250.0 to 400.0°C
-200.0 to 1300.0°C
-200 to 900.0°C
-200.0 to 600.0°C
-20.0 to 1767.0°C
600.0 to 1820.0°C
0.0 to 2315.0°C
-200.0 to 800.0°C
0.0 to 2500.0°C
-11.000 to ±99.999.mV
Type K, E, T, L, U: 0.5°C for 0<t<500°
mV: 0.015% +10μV (max 10mA out)
Dimensions: 7.5" x 3.6" x 1.65" (192 x 90 x 42mm)
Includes test leads, batteries & carrying case. AC
adapter sold separately (P/N 94013).
CA330
SPECIFICATIONS
Pt100 (3851)
Pt100 (3850)
Pt100 (3916)
Pt100 (3926)
Pt200 (3851)
Pt500 (3851)
Pt1000 (3851)
Cu10 (427)
Ni120 (627)
Pt50 (3851)
Pt50G
Pt100G
Cu50M
Cu100M
500Ω
3000Ω
Accuracy:
-200.0 to 800.0°C
-200.0 to 630.0°C
-200.0 to 510.0°C
-200.0 to 630.0°C
-200.0 to 630.0°C
-200.0 to 630.0°C
-200.0 to 630.0°C
-100.0 to 260.0°C
-80.0 to 260.0°C
-200.0 to 630.0°C
-200.0 to 800.0°C
-200.0 to 630.0°C
-180.0 to 200.0°C
-180.0 to 200.0°C
0.00 to 550.00Ω
0.0 to 3300.0Ω
Pt100, Pt200: 0.033% +0.3°C
Ω: 0.025% +0.5Ω
Dimensions:
7.5" x 3.6" x 1.65" (192 x 90 x 42mm)
Includes test leads, binding posts, batteries & carrying
case. AC adapter sold separately (P/N 94013).
Extech Process Calibrators
VOLTAGE/CURRENT
THERMOCOUPLE
• Measure & source (simulate) 8 T/C types
• Display ºC, ºF or mV
• 5 user adjustable presets
• Miniature thermocouple
connector
• Battery or AC power
• Source to 24mA, 20V
• Measure to 50mA, 20V
• 5 user adjustable presets
• Banana connections
• Battery or AC power
PRC15
PRC20
SPECIFICATIONS
SPECIFICATIONS
Source:
0 to 24mA (-25% to 125%), <1kΩ load
0 to 20V
Measure:
0 to 50mA (-25 to 230%);
0 to 19.99V
Input/Output: Range
Resolution
0 to 19.99mA
0.01mA
0 to 24.0mA
0.1mA
0 to 1999mV
1mV
0 to 20.00V
10mV
Accuracy:
0.01% +1 digit
Dimensions: 6.3" x 3.2" x 1.7" (159 x 80 x 44mm)
Includes test leads, AC power adapter, batteries & hard
carrying case
Type J
Type K
Type T
Type E
Type C
Type R/S
Type N
Voltage:
Resolution:
-58 to 1832°F (-50 to 1000°C)
-58 to 2498°F (-50 to 1370°C)
-184 to 752°F (-120 to 400°C)
-58 to 1382°F (-50 to 750°C)
32 to 3182°F (0 to 1750°C)
32 to 3182°F (0 to 1750°C)
-58 to 2372°F (-50 to 1300°C)
-10.00mV to +60.00mV
0.1° (up to 999.9) or 1° (over 999.9°)
for J, K, T, E ; 1° for R, N; 0.5° for C, S
0.05% rdg +1° 0.015% ±3 digitor 10μV
Accuracy:
+1d
Input Z:
10 MΩ
Dimensions: 6.3" x 3.2" x 1.7" (159 x 80 x 44mm)
Includes calibration cables, AC power adapter, batteries
ORDERING INFORMATION
EX/PRC15
EX/PRC20
EX/PRC30
165a
Voltage/Current Calibrator
Thermocouple Calibrator with Cold Junction Compensation
Multifunction Calibrator with Cold Junction Compensation
add -NIST to P/N for
NIST traceable Certificate
of Calibration
MULTIFUNCTION
• Source/Measure
Voltage, Current, mV &
Thermocouples
• Combines functions of
the PRC15 & PRC20
• 24V loop power source
PRC30
SPECIFICATIONS
DC Source:
Current
0 to 24mA (-25% to 125%), <1kΩ load
Voltage
0 to 2000mV, 0 to 20V
mV/Temp -5 to 55mV
DC Measure:
Current
0 to 50mA, -25% to +230%
Voltage
0 to 1999mV / 2 to 20V
mV/Temp -10 to 60mV
Thermocouple Source/Measure:
Type J
-58 to 1832°F (-50 to 1000°C)
Type K
-58 to 2498°F (-50 to 1370°C)
Type T
-184 to 752°F (-120 to 400°C)
Type E
-58 to 1382°F (-50 to 750°C)
Type C, R, S 32 to 3182°F (0 to 1750°C)
Type N
-58 to 2372°F (-50 to 1300°C)
Accuracy:
V/I/mV: 0.01% + 1 digit
T/C: 0.05% + 2°F or 1°C
Loop Power: 24V
Dimensions: 6.3" x 3.2" x 1.7" (159 x 80 x 44mm)
Includes test leads, calibration cables, AC power
adapter, batteries & hard carrying case
Martel Beta Process Calibrators
Universal Temperature
L
Multi-Function
MC–1210
• Calibrates thermocouples, RTDs,
transmitters & meters
• Displays cold junction & mV equivalent
• Direct keyboard entry or scroll control
• ASCII RS-232 & USB interface
• Rugged IP54 case
• High accuracy: ±0.4°C Type J T/C,
±0.2°C Pt100 RTD
PTC–8010
• Auto step & ramp
L
• Measure and source T/Cs, RTDs, ohms,
current, voltage, frequency; source pulse trains
• Isolated mA/V read-back for complete
transmitter calibration
• Dual display (volts/mA, source/measure)
• Automatic cold junction compensation
• Tests pressure & temperature switches
• Auto step & ramp with setpoints
• Complete serial interface for remote control
• Rugged IP54 case
SPECIFICATIONS
SPECIFICATIONS
Read and Source
Voltage
Current (mA)
Source
0.000 to 20.000 VDC
0.000 to 24.000 mA
Read Isolated
0.000 to 30.000 VDC
0.000 to 24.000 mA
Read Non-isolated
0.000 to 20.000 VDC
0.000 to 24.000 mA
Accuracy
±0.015% of rdg ±2 mV
±0.015% of rdg ±2 µA
Millivolts (mV)
Frequency
Read & Source
-10.000 to +75.000 mV
CPM Source & Read 2.0 to 600.0 CPM
Accuracy
±0.02% of rdg, ±10 µV
Hz Source & Read 1.0 to 1000.0 Hz
kHz Source & Read 1.0 to 10.00 kHz
Ohms
Accuracy
0.05% ±1d
Source
5.0 to 4000Ω
Read
0.00 to 4000.0Ω
Read and Source
Range (Accuracy) *°C
Accuracy
0.025%
±5d
J
-210.0 to +1200.0 (0.2)
K
-200.0 to +1370.0 (0.3) Read and Source Range (Accuracy) °C
-80.0 to +260.0 (0.2)
Ni120
T
-250.0 to +400.0 (0.2)
-200.0 to +800.0 (0.2)
E
-250.0 to +1000.0 (0.2) Pt100 (385)
Pt100 (3926)
-200.0 to +630.0 (0.2)
R
-20.0 to +1767.0 (1.2)
Pt100 (3916)
-200.0 to +630.0 (0.2)
S
-20.0 to +1767.0 (1.2)
-200.0 to +630.0 (0.7)
B
+600.0 to +1820.0 (1.2) Pt200 (385)
Pt500 (385)
-200.0 to +630.0 (0.3)
C
0 to +2316.0 (0.6)
Pt1000 (385)
-200.0 to +630.0 (0.2)
XK
-200.0 to +800.0 (0.2)
Cu10
-100.0 to +260.0 (1.3)
BP
0 to +2500.0 (0.9)
YSI400
+15.00 to +50.00 (0.1)
L
-200.0 to +900.0 (0.2)
Cu50
-180 to +200 (0.3)
U
-200.0 to +600.0 (0.25)
-180 to +200 (0.1)
N
-200.0 to +1300.0 (0.4) Cu100
-200 to +800.0 (1.4)
*T/C basic accuracy with CJC off; same as Pt10 (385)
PTC-8010 with CJC on
-200 to +800.0 (0.4)
Pt50 (385)
Operating Temperature:
Protection:
Dimensions
-10 °C to +50 °C
Protected against misconnection to 250V AC/DC
8.5" H x 4.8" W x 2.1" D (22x12x5.3cm)
Loop Calibrator
L
LC-110
SPECIFICATIONS
Current Source & Measure
Range:
0.000 to 24.000 mA,
-25 to +125 %
Voltage (Reading): 0 to 30 VDC
Protection:
240 VAC, 28mA DC
Simulates defined mA values
Valve Test:
with % keys
Loop Supply:
24 VDC @ 20mA
9800 records or 99 sessions,
Data Storage:
1
to to 60 second interval
Resolution:
1 µA, 1mV
Accuracy:
±0.01% of reading ± 2 digits
-10 to +55 °C
Operating Temp.:
6" x 3.6" x 1.3"
Dimensions:
Accy*
0.4°
0.5°
0.4°
0.4°
1.4°
1.4°
1.5°
0.4°
0.5°
0.6°
0.02%
Ni120
Pt 100 (385)
Pt 100 (3926)
Pt 100 (3916)
Pt 200 (385)
Pt 500 (385)
Pt 1000 (385)
Cu100
YSI400
Ohms
-80.0 to 260.0
0.1°
-200.0 to 800.0 0.2°
-200.0 to 630.0 0.2°
-200.0 to 630.0 0.2°
-200.0 to 630.0 0.7°
-200.0 to 630.0 0.3°
-200.0 to 680.0 0.2°
-180.0 to 200.0 0.1°
15.0 to 50.0
0.1°
0.00 to 400.00, 0.025%
401.0 to 4000.0
plus Pt10/50, Cu10/50 RTDs; C, XK, BP T/Cs
Connectors:
Standard mini-plug for T/C, banana jack for RTDs
-10 to +50 °C
Operating Temp.:
Dimensions:
8.5" H x 4.8" W x 2.1" D (22x12x5.3cm)
*Basic Accuracy with thermocouple CJC on or 4-wire RTD connection
ORDERING INFORMATION
Multi-Function Calibrator with test leads, carrying
case, 4 AA batteries, NIST certificate
MA/PTC-8010
Universal Temperature Calibrator with test leads,
carrying case, 4 AA batteries, NIST certificate
MA/IVC-222
HP11 Voltage/Current Calibrator with test leads,
carrying case, 9V battery, NIST certificate
MA/TC-100
Thermocouple Calibrator with 9V battery,
NIST certificate
MA/LC-110
Loop Calibrator with test leads, 6 AAA batteries,
NIST certificate
A variety of temperature probes, test leads, cables and software are available.
MA/MC-1210
Thermocouple Calibrator
Voltage/Current Calibrator
• 10 T/C types plus mV
• ±0.3°C accuracy (type J)
• Accepts T/C mini-plug
& bare T/C wires
• 3 setpoints for each T/C type
• MIN/MAX recall in
measure mode
• Input protection to 240 VAC
• 0.015% of reading
accuracy
• 200 mV, 2 V, 20 V and
24 mA ranges
• 24 V supply can drive
4-20 mA loops
• 2 stored setpoint values
• Intuitive, easy-to-use
controls
IVC-222HPII
TC-100
L
SPECIFICATIONS
Voltage Source & Measure
Range:
Resolution:
Accuracy:
Output Impedance:
Input Impedance:
-10 to +75.000 mV
1 µV
±0.007% of reading,
±10 µV
≤1 Ω
>1 MΩ
Thermocouple Source/Measure
Types:
J, K, T, E, R, S, B, L, U, C
Resolution:
0.1°C or °F source
0.01°C or °F measure
Operating Temp:
-10 °C to +55 °C
Dimensions:
5.7" x 3.15" x 1.43"
TEST
EQUIPMENT
• Simulate, power & measure
two-wire transmitters
• Five preset outputs
(4, 8, 12, 16, 20 mA)
• 0.001 mA resolution
• Adjustment level knob
• Variable step and ramp time
• Measures loop power
• Hart protocol (LC-110H)
Read/Source Range °C
J
-210.0 to 1200.0
-200.0 to 1370.0
K
-250.0 to 400.0
T
E
-250.0 to 1000.0
-20.0 to 1767.0
R
S
-20.0 to 1767.0
B
600.0 to1820.0
-200.0 to 900.0
L
U
-200.0 to 600.0
N
-200.0 to 1300.0
mV -10.000 to 75.000
L
SPECIFICATIONS
Resolution
Voltage:
Current:
Accuracy:
Temp. Stability:
Load Capability
Voltage:
Current:
Output Protection:
Operating Temp:
Dimensions:
0.01 mV, 0.0001 V, 0.001V
0.001 mA
±0.015% of reading, ±2 count;
18 °C to 28 °C
±0.005% FS/°C
±1 mA for rated accuracy
1kΩ
Current limited internal RESET
-10 °C to +55 °C
1.43" x 3.15" x 5.7"
166
Fluke Process Loop Calibrators
Fluke 707 Loop Calibrator
705 Features, Plus:
• Output Adjustment Dial
• HART™ Mode
• 0.015% Accuracy
SPECIFICATIONS
Functions
Voltage measurement
Range
Resolution
Accuracy
Current measurement
Range
Resolution
Accuracy
Current sourcing
Range
Accuracy
Drive capability
Loop power while
measuring mA
Voltage sourcing
Resistance
measurement
Frequency
Diode test
Continuity
Display current
and % of span
Auto step, auto ramp
Span Check
Fluke 705 and 707
Fluke 715
Fluke 787 and 789
0-28 V dc
0-100 mV 0-10 V
0.001V
10 µV 1 mV
705: 0.025% Rdg + 1 LSD 0.02% Rdg + 2 LSD
707: 0.015% Rdg + 2 LSD
0-1000 V ac or dc
0.1mV to 1.0V
0.1% Rgd + 1 LSD (VDC)
0-24 mA
0-24 mA
0.001 mA
0.001 mA
705: 0.02% Rdg + 2 LSD 0.015% + 2 LSD
707: 0.015% Rdg + 2 LSD
0-1A dc
1mA dc
0.2%+2 LSD
0-20 mA or 4-20 mA1
705: 0.025% Rdg + 2 LSD
707: 0.015% Rdg + 2 LSD
705: 1000Ω @ 24 mA
707: 1200Ω @ 24 mA
24V
0-20 mA or 4-20 mA1
0.015% Rdg + 2 LSD
0-20 mA or 4-20 mA1
0.05% of span
1000Ω @ 24 mA
24V
787: 500Ω @ 24 mA
789: 1200Ω @ 24 mA
24V (789 only)
N/A
N/A
0-100 mV or 0-10V
N/A
N/A
to 40MΩ, 0.2% + 1 LSD
N/A
N/A
N/A
Yes
N/A
N/A
N/A
mA or %
to 19.999 kHz,0.005% + 1 LSD
2.4 V shows diode voltage drop
Beeps for resistance <100 ohms
Yes
Yes
Yes
No
No
Yes
789 only
0-30 mA dc
0.001 mA dc
0.05%+2 LSD
Fluke 787 Process Meter
• DMM and Loop Calibrator
• Backlit LCD
• 1000V Overload Protection on V, Ohms,
Frequency
Fluke 789 Process Meter
787 Features, Plus:
• 24V Loop Power Supply
• HART™ Mode
• Fast “Span Check”
Fluke 715 Volt/mA Calibrator
• Measure loop Currents and Process
Voltages
• Source Loop Currents to 24mA
• Source Voltage to 10V
705
1
Will over-range to 24 mA
787
L
Fluke 705 Loop Calibrator
• Simultaneous mA and % Readout
• Fast “Span Check”
• Selectable Slow Ramp,
Fast Ramp & Step
• 24V Internal Loop Supply
L
Fluke Temperature Calibrators
TEST
EQUIPMENT
Fluke 712B RTD Calibrator
• Measure & simulate 13 RTD types & resistance
• Measure 4-20mA signals while sourcing an
` RTD signal
• Configurable 0% to 100% source for quick
` 25% linearity checks
• Linear ramp & 25% auto ramp
• Power down settings remembered at power up
• Dual inputs & backlit display
• Hanging tool built into case
• 1 and 2 year specs plus traceable
` certificate of calibration ` `
Fluke 714B Thermocouple Calibrator
• Measure & simulate 17 TC types
• Measure 4-20mA signals while sourcing
a thermocouple signal
• Configurable 0% to 100% source for quick
` 25% linearity checks
• Linear ramp & 25% auto ramp
• Power down settings remembered at power
up for easy restart of tests
• Dual inputs & backlit display
• Hanging tool built into case
• 1 and 2 year specs plus calibration certificate
SPECIFICATIONS
Model
Fluke-712B
Fluke-714B
Both Models
167
Function
Measure/simulate
RTD
Range
-200 to 800°C,
depending on type
Resolution
0.1°C
Measure/simulate
Resistance
Measure/simulate
Thermocouple
Measure/source mV
Measure DC mA
0 to 400Ω
40 to 4000Ω
-250 to 2500°C,
depending on type
-10 to 75 mV
0 to 24 mA
0.01Ω
0.1Ω
0.1°C
0.01 mV
0.001 mA
1 yr Accuracy
0.015%+0.18°C
(Pt 100, 100-800°)
Types
Pt 10 50 100 200 500 1000 (385);
Pt 100 (3916 3926); Ni 120 (672);
Cu 10 50 100 (427); YSI400
0.015% + 5d
0.3°C
J K T E N R S B C L U G D P BP XK M
(Type K -100 to 400°) (K range = -200 to 1372°C)
0.015% + 1d
0.010% + 2d
Simpson Analog VOM
• Industry Standard Model 260
• 36 Measurement Ranges
• Mirrored Scale
• CAT III-600V (260-95)
• 10A AC (260-95)
• 1000V AC/DC Max (260-8)
ORDERING INFORMATION
Description
General Purpose, Phenolic Case
Relay Protected
Roll Top Case
Relay-Protected, w/Roll Top Case
Yellow ABS Plastic Case
Yellow Case, Relay-Protected
SI/12397
Safety VOM Orange, with Case
260-9S
SI/12398 260-9SP
Safety VOM Protected, with Case
ACCESSORIES
Cat. #
for Model
SI/00043 260-8, 8P
SI/00125 260-8XI,
8XPI
SI/00834 Any 260-8
SI/00805 Any 260-8
SI/00541 260-8XI, 260-8XPI,
9S, 9SP
SI/00545 260-8, 8P, 8RT,
8PRT, 95, 95P
SI/00425 260-8X, 9
Description
Probe Set, threaded w/clips
Probe Leads w/Screw-On
Alligator Clips
Black nylon padded case
Black Leatherette case
250A AC Clamp
250A AC Clamp
L 260-8
260-9S
L
(Test Leads Included)
Cat. #
Model #
SI/12388 260-8
SI/12391 260-8P
SI/12389 260-8RT
SI/12392 260-8PRT
SI/12395 260-8XI
SI/12396 260-8XPI
Screw-on alligator Clips
Triplett Analog VOM
• 58 Ranges & Functions (Model 60-NA)
• Withstands 5 Foot Drop
• Mirrored Scale
L
• 3 Year Warranty
60
ORDERING INFORMATION
TR/3145
Model 60 VOM (Orange Case)
TR/3151
Model 60-NA (Gray Case)
Carrying Cases
TR/10-823 639 Carrying Case (Top Opening)
TR/10-2739 639-A Carrying Case (Snap back Cover)
TR/4152
639-C Padded Cordura Carrying Case
Test Leads
TR/79-373 Miniature Clip Leads (female jack)
TR/79-374
48" Test Leads w/ Screw-On Alligator Clips (female jack)
AC Amps Clamp-On
TR/3264
Model 101-G Line Separator
TR/60-211 Model 10 Clamp-On AC AMP Adaptor (60, 60-NA)
TR/79-417
6' Attachment Leads (60/ 60-NA to Model 10)
Weschler Columbia AC/DC Clamp-On Tong Test Ammeters
Plug-in Range modules: 0-100A, 0-150A, 0-200A, 0-300A, 0-400A,
0-500A, 0-600A, 0-800A, 0-1000A. The effective range can be
lowered by winding two or more turns of the conductor around
the tongs.
L
The Tong Test Ammeter reads the true RMS (heating) value, regardless of wave shape. It contains no batteries, rectifiers, switches or
electrical windings to overheat or burn out. Currents in lines up to
2300V can be measured if the cables are properly insulated. DC
accuracy is 5% of full scale, AC accuracy (25-100Hz) is 2%, except
5% on ranges above 500A. Add 1% for 100-400Hz.
TEST
EQUIPMENT
Ideal for verifying currrent in plating tanks, coating systems,
welding equipment, motors, generators & transformers
Clamp-On Tong Test Ammeters
• Instant Readings
• One Hand Operation
• No Transformers or Shunts Needed
ORDERING INFORMATION
for conductors up to 1 1/2" dia.
for conductors up to 2 1/2" dia.
for conductors up to 3" dia. or
bus bars to 4"x1" or 4 1/2"x 1/2"
Specify range model(s) when ordering.
Columbia AX
Columbia C
Columbia D
168
Yokogawa Test Standards
Decade Resistance Boxes
2793 6-Dial
Decade Resistance Box
2786
Decade Resistance Box
• Resistance value ranges:
0.100 to 1111.210Ω (2793 01)
0 to 111.1110MΩ (2793 03)
• Accurate, highly stable
• High reproducibility
• Resolution 0.001Ω
• Well-suited for resistance temperature
detector calibration (2793 01)
• Well-suited for insulation resistance
tester calibration (2793 03)
• Resistance ranges: 0.1 to 111,111Ω (2786 10)
1 to 1,111,110Ω (2786 20)
• Small temperature coefficient, little
temporal variation
• Small residual resistance
• Metal casing resists external
influences
Wheatstone Bridges
2768 Precision
Wheatstone Bridge
• Measurement range 0.1Ω to 111MΩ
• High precision ±0.01%
• Does not require accessories
• Built-in power source, current detector; external plug
• Highly stable measurement over long periods
• Also functions as a variable resistor
2755-97 Portable
Wheatstone Bridge
• Measurement range 1Ω to 10MΩ
• Does not require accessories
• Simple operation
• Current detector with built-in
protection circuit
• Compact, light-weight
TEST
EQUIPMENT
Double Bridges
2752 Precision
Double Bridge
2769 Portable
Double Bridge
• Measurement range 0.1Ω to 111MΩ
• High precision ±0.03%
• Stable over long periods
• Standard resistor built-in
• Allows testing of cylindrical resistors
using clamp device
• Measurement range 0.1Ω to 110MΩ
• Rapidly performs reliable, accurate
measurements
• Easy to handle and store
• Does not require accessories
• Built-in high sensitivity current sensor
Portable Meters
Portable AC Ammeters
and Voltmeters
Miniature Portable
Ammeters and Voltmeters
• Superior product line
• Highly reliable, incorporating 80 years of
meter manufacturing technology
• Low friction, withstands impact,
tautband technology
• Compact, light-weight
• Superior product line
• Highly reliable, incorporating 80 years of
meter manufacturing technology
• Low friction, withstands impact,
tautband technology
169
Monarch Optical Tachometers
L
• Operating Range up to 25 Feet
• Accepts Remote Contact Assembly (optional)
• Accepts Remote Sensors (optional)
• TTL Pulse Output
• Auto Ranging or Fixed Decimal
• English and Metric Rates
• Tripod Mounting Bushing
• On-Target and Low Battery Indicators
• Rugged Rubberized Housing
• N.I.S.T. traceable Certificate of Calibration
PLT200
PLT200 SPECIFICATIONS
Display:
Optical Range:
Contact Range*:
Optical Accuracy:
Contact Accuracy*:
Resolution:
Operating Range:
Light Source:
Memory:
Power:
Environmental:
Dimensions:
Weight:
5 digit alpha-numeric LCD
5 to 200,000 RPM
0.5 to 20,000 RPM (other ranges: inches, yds,
miles, cm, m per hour or per second)
±0.01% of reading
±0.05% of reading (RPM)
0.001 to 10 RPM (range dependent)
2 inches to 25 feet
Class 3R visible laser
Maximum, Minimum and Last
(2) AA batteries
5° to 40°C (0° to 100°F)
80% RH up to 31°C (88°F)
6.92 “H x 2.4”W x 1.6”D
7 oz. (210 g)
* with optional Remote Contact Assembly (RCA).
PLT200 is a 32 function Laser Tachometer and Ratemeter/
Totalizer/Counter/Timer (stopwatch). The unit is program–
mable in both English and Metric rates. Support is built-in
for the optional Remote Contact Assembly (RCA) and plug-in
remote sensors. A TTL compatible pulse output can trigger
devices like data collectors or stroboscopes. The ergonomic
design allows safe, direct line-of-sight viewing of both the
target and the display at the same time. The case has a
no-slip rubber surface for single hand operation.
PT99 SPECIFICATIONS
Display:
Range:
Accuracy:
Resolution:
Dimensions:
Weight:
Measurement
• Operating Range up to
36 Inches
L
Operating Range:
Light Source:
Memory:
Power:
Environmental:
• Non-Contact Optical
5 digit alpha-numeric LCD
5 to 99,999 RPM
0.01% of reading or ±1 Digit
Autoranging: 0.001 to 1.0 RPM
Fixed:
1 RPM
2 to 36 inches
Red LED
Maximum, Minimum & Last
(2) AA 1.5 VDC batteries
5° to 40°C (0° to 100°F)
80% RH up to 31°C (88°F)
6.92"H x 2.4"W x 1.6"D
7 oz. (210 g)
PT99
• Rugged, Ergonomic
Rubberized Housing
• Tripod Mounting for
Hands Free Operation
• Autoranging or Fixed Decimal
Direct line-of-sight viewing of both
the rotating target and the display
at the same time.
TEST
EQUIPMENT
ORDERING INFORMATION
Catalog No.
MODEL
MN/6125-010
PLT200
MN/6125-011
PLT200 KIT
MN/6109-010
PT99
Accessories for PLT200
MN/6180-057
ROS-P
MN/6180-057-25 ROS-P-25
MN/6180-017
MT-190P
MN/6180-020 IRS-P
MN/6180-028 EC-25P
MN/6280-037 CA-4044-6
MN/6180-074
RCA
MN/6580-010
CTE
MN/6580-011
12" Contact Wheel
Accessories for both models
MN/6180-047
CC-10
MN/6180-048 CC-11
MN/6180-070
T-5
DESCRIPTION
Pocket Laser: Tachometer/Timer/Totalizer with N.I.S.T. traceable certificate of calibration and 12" of reflective tape.
Pocket Laser Tachometer Kit includes: Tach, RCA, Carrying Case, N.I.S.T. certificate and 5 ft roll of T-5 reflective tape.
Pocket Tachometer with 12" of reflective tape
Remote Optical Sensor with 8-foot cable, mounting bracket and 12" of reflective tape.
Remote Optical Sensor with 25-foot cable, mounting bracket and 12" of reflective tape.
Magnetic trigger Sensor/Amplifier with 8 foot cable
Infrared Sensor with 8 foot cable, 3.5 mm plug and mounting bracket
25 foot extension cable for all sensors
6 foot input/output cable, 1/8 inch mono phone plug to BNC connector
Remote Contact Assembly includes contact tips (concave and convex) and 10 cm linear contact wheel.
Rubber concave, convex tips and 10 cm contact wheel
Linear Contact Wheel with 12-inch circumference for use with RCA.
Padded Pouch
Latching Plastic Carrying Case.
Reflective Tape 5 foot roll, 0.5 " wide
170
Monarch LED Stroboscopes
NEW
Nova-Strobe
• Brightest portable LED strobes available
• For diagnostic inspection and RPM checks
• Digital LCD backlit display (DBL, PBL models)
• Lightweight design with tripod mount bushing (¼-20) in handle
• 12 button keypad for quick entry of flash rates (DBL, PBL)
• NIST certificate included with DBL and PBL models
• Continuous, 24/7 operation (PBL)
BBL Basic
DBL Deluxe
PBL Phaser
Flash Range (FPM/RPM):
30-500,000
Display:
6 digit numeric and 5 digit alphanumeric LCD
Accuracy/Resolution:
0.002% of setting or ±1 least significant digit/ 0.01 FPM
Light Output:
3000 Lux @ 6000 FPM, 8 inches (20cm), 2% duty cycle
Flash Duration:
Adjustable to 14 degrees /3000μsecs max
Light Source:
12 LED Array
Color Temperature:
6300°K
External Triggers in/out:
N/A
TTL (24Vdc Max) Input. Provides 3.3 Vdc TTL output
Tachometer Mode:
N/A
0-500,000 RPM (Use with optional remote sensor)
Programmable Memory:
N/A
Yes
Internal Phase Shift:
N/A
Yes
Phase Delay - Degrees:
N/A
0.1 to 359.9 degrees
Time Delay (milliseconds:
N/A
0.01 to 1000 msec.
Virtual RPM (Slow Motion):
N/A
0-200 VRPM
Operating Time (AC power):
N/A
continuous
Operating Time (battery power):
8-10 hours typical @ 1800 FPM
Batteries:
Internal NiMH rechargeable (120/240V charger included)
Size (L x W x H)/Weight:
Body: 9" x 3.66" x 3.56" (229 x 93 x 90 mm); Reflector Housing: 4.8"
(122mm) dia.; Handle: 4.254" (108 mm long) / 1.9 Lbs (860g)
PLS
Pocket LED Strobe
• Intuitive one hand operation
• Extremely bright, uniform light
• Quiet/Cool operation
• Digital LCD backlit display
• Compact size, long battery life
• Tripod mounting bushing (¼-20)
• No lamp replacements
• NIST Certificate included
Catalog No.
MN/6230-010
MODEL
Nova-Strobe BBL
MN/6230-011
MN/6231-010
Nova-Strobe BBL Kit
Nova-Strobe DBL
MN/6231-011
MN/6232-010
Nova-Strobe DBL Kit
Nova-Strobe PBL
MN/6232-011
Nova-Strobe PBL Kit
MN/6235-010
PLS
MN/6235-011
Accessories
MN/6180-029
PLS Kit
MN/6280-048
MN/6280-040
MN/6280-073
MN/6180-070
ROLS-P
T-5
DESCRIPTION
BBL Strobe, universal 115/230 recharger with
interchangeable wall plugs & manual
Same as above with plastic latching carry case
DBL Strobe, universal 115/230 recharger with
interchangeable wall plugs, manual & NIST Cert
Same as above with plastic latching carry case
PBL Strobe, 115/230 power supply/recharger
with USA and Euro cables, manual & NIST Cert
Same as above with Deluxe water tight plastic
carry case
Pocket LED Strobe, 115/230 VAC recharger with
interchangeable wall plugs, manual & NIST Cert
Same as above with latching carry case
Remote optical laser sensor with 8 ft cable,
1/8” phone plug & 12” reflective tape
Protective rubber cover for Nova-Strobes
Standard latching carry case for Nova-Strobes
Protective carry pouch with belt hook for PLS
Reflective Tape 5 foot roll, 0.5 " wide
Nova-Strobe industrial stroboscopes provide
a bright, uniform light output. The twelve LED
source is extremely efficient, which means
long battery life & continuous cool operation.
A wide operating range of 30-500,000 flashes per minute covers all applications. The
Basic BBL is designed for simple stop motion
inspection and RPM measurements. The
Deluxe DBL adds internal phase shifting,
memory for 5 preset flash rates, NIST calibration certificate and tachometer mode for
speed measurements up to 500,000 RPM
using optional remote sensors or TTL pulse
input. The top of the line Phaser PBL has all
the features of the DBL plus external phase
delay, time delay & virtual RPM mode. The
PBL will also run continuously with the power
supply/recharger.
PLS SPECIFICATIONS
Light Source:
Avg. Light Output:
Color Temp:
Power:
Run Time:
Charge Time:
Memory:
Flash Duration:
Internal Mode:
Flash Range:
Accuracy:
Resolution:
7 LED Array
1800 Lumens at 6000 FPM 8" from lens
5600°K
Li-Ion rechargeable batteries 3.6Vdc
5-6 hours typical at 6000 FPM
4-5 hours typical with supplied charger
5 user settable memory locations
Adjustable 0.5 to 2500 μsec or 0.1 to 18 deg.
of rotation (auto adjusts with flash rate)
30-300,000 FPM (Flashes per minute),
0.5 to 5000Hz
0.005% of setting or ± last digit
0.01 to 1 FPM (menu selectable), 0.1 FPM resolution above 9,999.99 FPM, 1 FPM resolution
above 99,999.9
External Modes:
Flash Range:
Tachometer Mode:
Accuracy:
Display Update:
Trigger to Flash:
External Input:
0-300,000 FPM, 0 to 5000Hz
30 to 300,000 RPM
±0.005% of reading or ± last digit
0.5 second typical above 120 RPM
~15 μsec delay
2.5-12V peak pulse, 500ns min pulse width,
pos. or neg. edge triggered (menu selectable)
Pulse In to Out Delay: <0.2μsec
Output Pulse:
3V pulse. One pulse per flash in internal mode.
Mimics input pulse in external mode
LCD Display:
6 digit numeric plus 5 digit alpha-numeric
Indicators:
Battery level, On Target, Select, TACH, EXT icons
Dimensions:
7.75" x 2.75" x 2.3" (197 x 70 x 58 mm)
170a
TEST
EQUIPMENT
ORDERING INFORMATION
Nova-Strobe
DBL
NOVA-STROBE SPECIFICATIONS
Amprobe Tachometers
• Contact and non-contact measurement
• Select rpm using infrared beam or adapter:
m/min, m/sec, ft/min, ft/sec, in/min,
m, ft, in
• Stores maximum, minimum, average &
last measurement
• Auto power off function
Includes 6 adapters, carrying case, reflective
tapes, 2 AA batteries and user manual
TACH20
TEST
EQUIPMENT
SPECIFICATIONS
Measuring Ranges:
Optical
Mechanical
Speed
m/min
ft/min
in/min
m/sec
ft/sec
Length
Accuracy
Sensing Distance
Operating Temp.
Housing Material
Dimensions
1 - 99999 RPM
1 - 19999 RPM
Ø 01 m
Ø 6"
Ø 12"
0.10 - 1999
0.10 - 1524
0.40 - 609.6
0.40 - 6550
0.40 - 5000
0.40 - 2000
4.00 - 78700
4.00 - 60000 4.00 - 24000
0.10 - 33.30
0.10 - 25.40 0.10 - 10.16
0.10 - 109
0.10 - 83.33 0.10 - 33.30
0 - 99999 m / 0 - 99999 ft / 0 - 99999 in
±0.02% of reading ±1 digit
600 mm / 24 in max. (optical)
0 to 50°C (32 to 122°F)
ABS
175 x 60 x 28 mm (7 x 2.5 x 1 in)
• Measures rotational & surface speed
• Non-contact measurement in RPM
• Contact measurement in RPM, m/min,
ft/min, yd/min (user selectable)
• 5 digit display
• Auto power off function
Includes cone & funnel contact tips,
reflective tape, 9V battery, user manual
SPECIFICATIONS
Measuring Ranges:
Rotation
10.0 - 99999 RPM (Non-contact)
10.0 - 19999 RPM (Contact)
Surface Speed 1.0000 - 9999.9 m/min
(Contact)
3.0000 - 30,000 ft/min
1.0 - 10,000 yd/min
Resolution:
RPM
0.001/0.01/0.1/1
M/Min
0.0001/0.001/0.01/0.1
Ft/Min
0.0001/0.001/0.01/0.1
Yd/Min
0.0001/0.001/0.01/0.1
Accuracy
±(0.1% of rdg.+2 digit)
Measure Distance 5-30 cm / 2-13 inches (non-contact)
Sampling Time
1 second (>60RPM),
>1 second (10~60RPM)
Operating Temp.
0 to 50°C (32 to 122°F), < 80% RH
Dimensions
267 x 178 x 82 mm (10.5 x 7 x 3.2 in)
Combo Tachometer
Contact / Non-Contact Tachometer
Extech Tachometer
• One touch tuning
• Flash rates to 12500 FPM
• Tachometer mode
• TTL compatible input/output
• Memory recall
• Measures RPM & surface speed
• Pocket size
• Laser guided non-contact measurements to 4.9 ft
• Reversible 5 digit LCD display
• Rechargeable battery
• Min/Max/Last reading memory
Four quadrant joystick button
adjusts flash rate, x2, ÷2.
Complete with cone tip and wheel for rpm
or linear surface speed, four AAA batteries,
and reflective tape.
Battery Run Time
Display
ORDERING INFORMATION
MN/6205-050
MN/6205-053
MN/6280-044
170b
Palm Strobe, with charger & NIST certificate
Palm Strobe Kit (Strobe, charger, NIST cert.,
spare battery, spare lamp, holster & case)
Protective Rubber Boot
NEW
SPECIFICATIONS
SPECIFICATIONS
Internal 100-12500 FPM
External 5-12500 FPM
Tach 5-250000 RPM
1 hour typical
6 digit backlit LCD
TACH-10
ORDERING INFORMATION
AB/TACH20
AB/TACH-10
Monarch Palm Strobe
Operating Modes
• Measures rotational and surface speed
Range
Surface Speed
(Contact mode)
Accuracy
Sampling Time
Resolution
5 to 99,999 rpm (photo mode)
0.5 to 19,999 rpm (contact mode)
2.0 to 78,740 inches/min
0.2 to 6560 ft/min
0.05 to 1999.9 m/min
±(0.1% rdg +1 digit)
1 sec
0.1rpm (<1000 rpm);
1rpm (>1000 rpm)
ORDERING INFORMATION
EX/RPM40
Pocket Laser Photo/Contact Tachometer
Extech Tachometers
Combination Laser Tach & IR Thermometer
SPECIFICATIONS
Display
Range
• Buit-in laser thermometer measures surface
temperature of moving parts
• Fixed 0.95 emissivity, 6:1 distance to
target ratio
• Non-contact photo tach measures to 6.5ft (2m)
• Contact tach for RPM & linear speed
• Min/Max/Last memory
• Complete with tips/wheel, AA batteries,
reflective tape, carrying case
RPM10
99999 counts
rpm
10 to 99999 photo
0.5 to 20000 contact
ft/min
L
Contact/Laser Photo Tachometer
• Laser guided non-contact measurements
to 6.5ft (2m)
• Characters on display reverse for easy
reading (photo/contact mode)
• Hold button stores last reading for 5 minutes
• Min/Max memory
• Complete with wheels, AA batteries, reflective
tape, carrying case
461995
0.2 to 6560
m/min
Accuracy
Resolution
Laser
0.05 to 1999.9
±0.05% ±1d
0.1 rpm
-4 to 650°F / -20 to 315°C (RPM10 only)
Dimensions
8.5 x 6.1 x 1.5" (216x66x38mm)
ORDERING INFORMATION
L
EX/RPM10
Combination Tachometer + IR Thermometer
EX/461995
Contact/Laser Tachometer
EX/461937
Reflective Tape 10pcs 1/4"x23"
EX/461990
Contact Wheels (cone tip, flat tip)
TEST
EQUIPMENT
Extech Light Meters
Model EA30 Wide Range Light Meter
• Measures up to 40,00Fc & 400,000Lux
• Large display with bargraph
• Relative function for zero or difference from
reference value
• Peak captures light pulses to 100ms
• Data hold & Min/Max store
• Complete with AAA batteries, light sensor and
protective cover with 39" (1m) cable, built-in
stand, protective holster & carrying case
Model EA31 EasyView® Big Digit Light Meter
•
•
•
•
•
Measures up to 20,000Fc/20,000 Lux
0.01Fc /0.01Lux resolution
2000 count display with bargraph
Data hold & Min/Max store
Complete with AAA batteries, light
sensor and protective cover with
39" (1m) cable, built-in stand,
protective holster & carrying case
Model 407026 Heavy Duty Light Meter with PC Interface
Enhance accuracy by selecting one of four lighting types plus PC interface
• % displays differential from reference point
• “ZERO” Re-Calibration
• Selectable lighting type Tungsten/Daylight, Fluorescent, Sodium, Mercury
• Data hold, Min/Max/Avg readings
• Auto power off
• Optional Data Acquisition software (407001) and Datalogger (380340)
• Complete with 9V battery, light sensor and protective cover with 3.8ft 1.2m)
cable, and protective holster with stand. Optional 117V or 220V AC adaptors.
ORDERING INFORMATION
SPECIFICATIONS
Model
Display counts:
Range: Fc
Lux
Max. Resolution:
Basic Accuracy:
Cosine & Color Corrected:
RS-232 Interface:
Datalogging:
Dimensions:
171
EA30
4000 (LCD)
40, 400, 4000, 40000
40, 400, 4000, 40000,400000
0.01Fc/0.01Lux
±3% rdg ±0.5% FS
Yes
—
—
407026
2000 (LCD)
200, 2000, 5000
2000, 20000, 50000
0.1Fc/Lux
±4% FS
Yes
Optional 407001
Optional 380340
5.9 x 2.8 x 1.4"
(150x72x33mm)
7 x 2.9 x 1.3”
(178x74x33mm)
EX/EA30
EX/EA31
EX/407026
EX/407001
EX/156119
EX/409997
EX/407001
EX/380340
Wide Range Big Digit Lightmeter
Big Digit Lightmeter
Heavy Duty Lightmeter
Data Acquisition Software & Serial Cable for 407026
117VAC Adaptor for 407026
Large Soft Vinyl Pouch Carrying Case for 407026
Data Acquisition Software & PC Serial Cable
Data Logger w/8000 Reading Storage, PC Software,
Serial Cable
Yokogawa Clamp-on Process Meter
Measure 4 to 20mA DC signals
without breaking the loop
• 0.2% Accuracy, 0.01mA Resolution
• Dual Display with Backlight
• LED Spot Light
• Analog Output
SPECIFICATIONS
Measurable Conductor:
DC Current:
20.00 mA Range:
100.0 mA Range:
Analog Ouput:
20.00 mA Range:
100.0 mA Range:
Display:
Response Time
Range Switching:
Operating Temperature:
Safety Standards:
Withstanding Voltage:
Power:
Battery Life:
Other Functions:
Dimensions:
6mm diameter max.
Measuring Range
Measuring Accuracy
0.00 to ±21.49mA
±(0.2%rdg +5dgt)
±21.0 to ±126.0mA
±(1.0%rdg +5dgt)
Output Range
Output Accuracy
0.0 to ±214.9mV DC
Measuring Accuracy +0.5mV
±210 to ±1260mV DC
Measuring Accuracy +3mV
4-digit LCD numeric display
Approx. 1.5 seconds (2.5 seconds when across the range)
Auto range
-10°C to +50°C, <80% RH (non-condensing)
EN61010-1, EN61010-2-030, EN61010-2-032
2.21kV AC for 5 seconds (between the core and the case)
Four AA-size alkaline batteries (1.5V LR6)
Approx. 60hrs (continuous) with backlight off and LED light off
Data hold, Zero adjust function, Auto power off, LED spot light, Back
light display, Illuminant panel
Meter: 61 x 111 x 40 mm; Probe: 104 x 34 x 20 mm w/ 700 mm cable
ORDERING INFORMATION
CL420
YE/CL420
YE/98076
YE/98077
Clamp-on Process Meter with batteries, manual & soft case
Analog Output Cable (banana plugs)
Analog Output Cable (for screw terminals)
Yokogawa Light Meters
Model 51011 & 51012 Digital Light Meters
• Measure to 999,000 lux
• Wide measurement range, high accuracy
• Spectral response characteristics for visible
range
• Good oblique incident light characteristics
• Recorder output & USB digital output
TEST
EQUIPMENT
Functions
51011, 51012:
51021:
Fatigue Characteristics:
Temperature Characteristics:
Characteristics of
Oblique Incident Light:
(deviation from cosine law)
51021
Model 51021 Multi Function Light Meter
Model 51012 Features plus:
• Color correction coefficient setting
• Light source brightness measurement
• Mean brightness calculation
ORDERING INFORMATION
YE/51011
YE/51012
YE/51021
Standard Conformance:
Model
Accuracy:
51011
51012
SPECIFICATIONS
Measuring Range:
Digital Light Meter (5 ranges)
High Accuracy Digital Light Meter (5 ranges)
Multi Function Light Meter (6 ranges)
51011& 51012: 0.0 to 99.9/999/9,990/99,900/999,000lx
51021: 0.00 to 9.99/99.9/999/9,990/99,900/999,000lx
510011, 51012: JIS C1609-1 2006 class A
51021: JIS C1609-1 2006 class AA
Response switching, Range Hold, Timer Hold, Deviation display, Auto off.
Response switching, Range Hold, Timer Hold, Deviation display, Auto off,
Color correction factor setting, Average illuminance computation,
Ripple measurement, Light source luminous intensity measurement,
Measurement of totalized intensity of illumination.
51011
51012, 51021
±4% rdg ±1dgt (under 3000lx)
±2% rdg ±1dgt (under 3000lx)
±6% rdg ±1dgt (over 3000lx)
±3% rdg ±1dgt (over 3000lx)
±2%
±1%
±5%
±3%
Angle of: 10° ±1.5%
Angle of: 10° ±1%
30° ±3%
30° ±2%
60° ±10%
50° ±6%
80° ±30%
60° ±7%
80° ±25%
Visible-Spectrum Response:
(deviation from standard
f1' within 9 %
f1' within 6 %
spectral luminous efficiency)
General Specifications (all models):
Photoelectric Element:
Silicon photodiode
Display:
7 digit liquid crystal display; maximum effective display: 999
Measurement Rate:
Twice per second
Response Time:
Automatic range: 5 sec; Manual range: 2 sec
Operating Temperature:
-10 to 40°C, <80% RH, non-condensing
Communication:
USB (Mini-b 5pin)
Output:
DC 1V ±5% (fixed range); 100kΩ min. load resistance
Dimensions:
67 x 177 x 38 mm
Power:
Two AA (LR6) batteries or USB supply (5VDC ±5%)
Accessories Included:
Instruction manual, battery, soft case, recorder output plug
171a
Bacharach Combustion Analyzers & Leak Detectors
Combustion Analyzer
• Measures CO with 1ppm resolution
• Highly visible digital display with
backlight
• Probe and hose assembly for flue
gas testing
• Optional IrDA printer
• Measures CO, O2, stack temperature,
ambient temperature
• Calculates CO2, combustion efficiency,
excess air, CO free air
• 10 record data storage
• Easy to use, quick sensor replacement
• 2 year warranty (1 year on O2 probe)
L
Carbon Monoxide Analyzer
Monoxor III
L
Fyrite InTech
SPECIFICATIONS
Range:
Accuracy:
Probe:
Warm Up:
Display:
Power:
Printer Port:
Size & Wgt:
Warranty:
0 - 2000 ppm
± 5% of reading or 10 ppm, whichever is greater
1000°F (538°C) max at 5" insertion
60 seconds
Four-digit LCD display w/backlight
4 AA Alkaline batteries (18 hour life)
Wireless, IrDA or HP protocol
7.5 x 3.1 x 2.1" (16 oz. with batteries)
2 years, including sensor
Combustible Gas Leak Detector
• Visual & audible indicators
• 2 sensitivity levels
• 12" probe with plug-in sensor
• Automatic calibration
• UL913 classification
L
SPECIFICATIONS
Variable rate flashing red, variable speed audible ticking
20ppm in high mode, 50ppm in low mode
60 seconds, flashes green when ready
4 AA alkaline batteries (14 hours life)
0-40°C operating
Handheld, 6 x 2 x 1.5" (6oz)
UL913 Class I, Div 2, Group A,B,C,D locations
L Informant 2
L Tru Pointe
Variable intensity audible & visual
0.1 oz/yr for R134a (hardest to detect)
1 yr of normal use (150 hours)
14" flexible, with plug-in sensor
2 D alkaline batteries (8-13 hr life)
2 x 9.4 x 2.5" (1.2 lbs with batteries)
UL listed to SAE J1627
Sensor:
Sensitivity:
Warm-up:
Power:
Size & Wgt:
Approvals:
Audible, sequential LEDs & flashing probe tip
All CFC, HCFC & HFC refrigerants, all combustible gases &
vapors
Located at probe tip for fast response & quick changeover
0.25 oz/yr of R134a (hardest to detect), 50ppm of methane
10 seconds
4 AA alkaline batteries (5 hr life)
1.8 x 9.7 x 2.3" with 20" probe
UL listed to SAE J1627, MET lab certified to UL913, intriniscally safe for Class 1, Div. 1, Group D hazardous locations
Includes batteries, refrigerant & gas sensors, sensor tips, filters and carrying
case.
ORDERING INFORMATION
BA/19-8104
BA/24-8511
BA/19-7075
BA/19-8038
BA/19-8106
Monoxor III CO Analyzer
Fyrite InTech C0, O2 Combustion Analyzer
Leakator Jr. Combustible Gas Leak Detector
Informant 2 Dual Detector Contractor Kit
Tru Pointe Refrigerant Leak Detector
172
TEST
EQUIPMENT
Indicators:
Detection:
SPECIFICATIONS
Indicators:
Sensitivity:
Sensor Life:
Probe:
Power:
Size & Wgt:
Approvals:
Dual Purpose Leak Detector
• Detects refrigerants & combustible
gases
• Swap sensors in seconds
• Sensitivity automatically adjusted
• 0.2" probe tip fits into tight spaces
• Filter prevents moisture
contamination
• Dual LED displays for easy viewing
• Optional rubber boot holds
flashlight
SPECIFICATIONS
Refrigerant Leak Detector
• Detects all CFC, HFC & HCFC
refrigerants
• Patented heated diode sensor
• Visual & audible indicators
• Automatic zero & background
correction
• 2 sensitivity levels
Measur ement Ranges
Flue Gas:
-4 to 1202°F (-20 to 650°C)
Ambient:
23 to 113°F (-5 to 45°C)
Oxygen:
0.0 to 20.9% O2
Carbon Monoxide:
0 to 2000 ppm CO
Calculat ed Ranges
Ca
Combustion Efficiency: 0.1 to 99.9%
Carbon Dioxide:
0.1 to a fuel dependent maximum (in %)
CO Air Free:
0 to 9,999 ppm
Excess Air:
0 to 250%
Selectable Fuels:
Natural Gas, Oil #2, Oil #6, Propane, Kerosene
Power:
4 AA alkaline (20 hours life)
Size & Wgt:
8.0 x 3.6 x 2.3" (16 oz. with batteries)
Includes angled probe/hose, batteries & soft carrying case.
Leakator Jr.
Indicators:
Sensitivity:
Warm-up:
Power:
Temperature:
Size & Wgt:
Safety:
SPECIFICATIONS
Megger® Hand-Held TDR / Cable Length Meter
•
•
•
•
•
•
•
Measures length of power, telephony, CATV & LAN cables
Determines distance to an open or short
Automatic impedance control (25, 50, 75, 100, 125, 150W)
Internal library of 39 standard cable types
Memory for 20 custom cable settings
Tone generator for cable tracing
Large, high resolution backlit LCD display
Additional Features:
Cable Calibration function allows measurement of V.O.P. (Velocity Of Propagation) in a known cable length.
Requires at least a 30ft (10m) sample.
Line Voltage Detection feature displays "OUCH" message and stops operation if voltage exceeds 6.5V.
SPECIFICATIONS
Range:
Resolution:
V.O.P.
Connector:
Power:
Battery Life:
Operating
Temperature:
-18°C to 60°C
* at 20°C for coax cables <8000 ft, telephony cables
<6000 ft, wiring <3000 ft
L
Accuracy*:
12000 ft (3.7km) at 99.9 V.O.P.
9800 ft (3.0km) at 80.0 V.O.P.
8000 ft (2.4km) at 66.0 V.O.P.
6200 ft (1.9km) at 50.0 V.O.P.
±2% of rdg ±20" at <300 ft
±2% of rdg at >300 ft
20 inches (50cm)
adjustable from 1.0% to 99.9% of the speed of light
BNC
4 AA batteries
5000 tests
TDR-900
Supplied with soft carrying case and alligator clip adapter.
ORDERING INFORMATION
ME/TDR900
Hand-Held TDR/Cable Length Meter
Megger® Hand-Held TTR
SPECIFICATIONS
L
TEST
EQUIPMENT
Excitation Voltage:
TTR20
8 V rms for testing distribution or power transformers & PTs;
0.5, 1.5, or 8 V ac rms for testing CTs (switched
automatically if current exceeds a preset value)
Test Frequency:
55 Hz
Excitation Current:
Range 0 to 100 mA, 4-digit resolution
Turns Ratio Range:
0.8 to 10000, 5-digit resolution
Transformer Polarity:
Normal or reversed
Current Accuracy:
2% of reading ±1 digit
Turns Ratio Accuracy:
0.1% (0.8 to 2000)
0.15% (2001 to 4000)
0.25% (4001 to 10,000)
Measuring Time:
Less than 5 seconds
Measurement Method: ANSI/IEEE C57.12.90
Phase Relationship:
ANSI C57.12.70-1978
Display:
Graphic LCD, adjustable back-lighting
Safety/EMC/Vibration: IEC-1010-1, CE and ASTM D999.75
Operating Temperature: -20º C to 55°C (-5°F to 130°F), < 90% RH non-condensing
Power:
Six standard AA alkaline batteries
Battery Life:
12 hours of field operation
Dimensions:
9.5"H x 4.5"W x 1.9"D (240x115x50 mm)
• Single- and three-phase transformer testing
• Fully automatic; fast; easy-to-use; robust; lightweight
• Battery powered
• Tests turns ratio, excitation current and polarity
• Simple, one-button operation
• Quick-start guide on front panel
173
ORDERING INFORMATION
ME/TTR20
Optional Accessories
ME/35942
ME/36013
ME/35755-1
ME/35788
Handheld TTR with 6ft (1.8m) test leads
Test leads, X/H winding, 12ft (3.6m)
Test leads, X/H winding, 20ft (6m)
Battery/line power thermal printer with paper, battery pack,
charger, interface cable
Semi-hard fabric transport case
Megger Time Domain Reflectometers
Dual Cursor Hand-Held TDR
Hand-Held TDR
• Single trace display with dual cursors
• Auto set-up for instant use
• 2 ns pulse width virtually eliminates dead
zones
• Trace HOLD with live trace overlay
• Designed for use on all metallic cable pairs
• Last setting memory
• IP54 rating
CFL510G
• Three-year warranty
• Simple handheld operation
• AUTO selection of gain & pulse width
• Ultra fast pulse for near end fault identification
• Trace HOLD feature
• IP54 rating
• Designed for use on all metallic cable pairs
• Three-year warranty
SELECTION GUIDE
Model
Measurement Ranges (ft):
Display:
Dual Cursors:
Fault Location Modes:
Accuracy:
Resolution:
Gain:
Velocity Factor
Output Impedance (Ω):
Output Pulse:
TDR900 *
6200-12000
4 ranges
Numeric
---1
±2 %
20 in. (50 cm)
---1.0 to 99.9%
25, 50, 75, 100,
125, 150
7 ns - 3 μs
TDR500/3
CFL510G
30-15000
7 ranges
Graphic LCD
---
1
3
±1 %
1% of range
3 steps
0.2 to 0.99
25, 50, 75, 100
25 ns - 3 μs
2 ns for
near fault
Pulse Amplitude:
5 V pk-pk
5 V pk-pk
5 V pk-pk
Low Battery Warning
Backlight
TX Null
---
Channels
1
1
1
Rating:
IP42
IP54
IP54
* see page 173 for specifications and ordering information
ORDERING INFORMATION
ME/CFL510G
Dual Cursor Hand-Held TDR w/ battery, case & test leads
ME/TCDR500/3 Hand-Held TDR with battery, case & test leads
ME/1002-015 Fused test lead set
SPECIFICATIONS
Range:
10/25/100/250/1000/2500/5000 m
(30/75/300/750/3000/7500/15000 ft)
Accuracy:
±1% of range ± pixel at 0.67 VF *
Resolution:
1% of range
Input protection:
Complies with IEC61010-1 for connection to live systems up to
150 V CAT IV when used with the optional fused test lead set.
Output pulse:
5 volts pk-pk into open circuit. Pulse widths determined by
range and cable.
Gain:
Set for each range with three user selectable steps (in manual
operating mode)
Velocity factor:
Variable from 0.2 to 0.99 in steps of 0.01
TX null:
Automatic
Power down:
Automatic after 5 minutes with no key press
Backlight:
Stays on for 1 minute with no key press
Battery:
Five LR6 (AA), Manganese alkali or nickel metal-hydride cells
Battery life:
Up to 14 hours (typical)
IP rating:
IP54 for use indoors or outdoors
Dimensions:
230 x 115 x 48 mm ( 9 x.0 x 4.5 x 2.0 inches)
Connectors:
Two 4 mm-safety terminals
Test lead:
1.5 meter long consisting of 2 x 4 mm shrouded connector to
miniature crocodile clips
Display:
256 x 128 pixel Graphics LCD
Temperature range: -15 ºC to +50 ºC (5 ºF to 122 ºF) operating
* Measurement accuracy is for the indicated cursor position only and is conditional
on the velocity factor being correct.
NEW
Megger Irradiance Meter & Photovoltaic Kit
PVM210
The Megger PVK330 Photovoltaic Kit features the PVM210 with the DCM340
AC/DC Clampmeter. The kit includes a set of 4 ft. red and black test leads (4mm
instrument plugs to MC4 solar connectors) and MC4 to MC3 adapters. Leads are
rated 19A 1000V. A zipped pouch is provided to store the instruments and leads.
SPECIFICATIONS
Display:
Range:
Accuracy:
3¾ digits LCD with maximum reading 3999
1999 W/m2 / 634 BTU /(ft2*h)
Typically within ± 10 W/m2 (±3 BTU / (ft2*h)) or ±5%,
whichever is greater in sunlight;
Temperature coefficient: ±0.38 W/m2/ºC (±0.12 BTU/(ft2*h)/ºC) from 25 ºC
Angular accuracy:
Cosine corrected <5% for angles <60 ºC
Accuracy:
<±3% per year
Resolution:
0.1 W/m2 / 0.1 BTU /(ft2*h).
Sampling time:
Approx. 0.25 second
Over input:
Display shows ” OL”
Operating temperature: 5 ºC~40 ºC, below 80% RH
Dimensions:
134 mm (H) x 48 mm (W) x 27 mm (D)
Battery life:
50 hr approx from 2 x 1.5 V AAA / MN2400
Auto off:
15 min.
Includes test leads, test probes, alligator clips, protective holster & batteries.
ORDERING INFORMATION
ME/PVM210
ME/PVK330
Irradiance Meter
Photovoltaic Kit
173a
TEST
EQUIPMENT
• Optimal incident angle & positioning of solar panels
• Measure solar power for panel short calculation
• 3¾ digit LCD display with 1999 W/m2 range
• Mini pocket size with built-in detector
• One hand use, with Display Hold
• Standard camera mount
PVK330
TDR500/3
Extech Sound Level Meters
• Two range meter with backlit LCD display
• Easy to use analog meter
• Measures 35 to 130dB
• Measures 54 to 126dB in 7 ranges
• Meets ANSI & IEC 651 Type 2 standards
• Selectable A or C weighting
• Data Hold & Max Hold functions
• Fast or slow response
• NIST certification available
• Analog output for recorder or datalogger
• Battery check
• Tripod mount
407730
SPECIFICATIONS
Basic Accuracy
Display
Microphone
Power
Dimensions
SPECIFICATIONS
±1.5dB
2000 count backlit LCD
0.5" condenser type
9V battery
8.2 x 2.1 x 1.25" (210x55x32mm)
Basic Accuracy
Analog Output
Microphone
Power
Dimensions
±2dB @94db, 1000Hz
AC: 0.707V rms
Built-in 0.5" Electret condenser type
9V battery
7.1 x 2.7 x 1.4" (180x68x36mm)
ORDERING INFORMATION
ORDERING INFORMATION
EX/407732
EX/407732-NIST
Applications:
407732
- Product noise testing
- Installing audio system
- Meeting OSHA safety issues
- Enforcing community noise ordinances
Digital Sound Level Meter
Digital Sound Level Meter with NIST Cert
EX/407703A
Analog Sound Level Meter
EX/407703A-NIST Analog Sound Level Meter with NIST Cert
Extech Testers
Battery Powered
Milliohm Meter
Battery Capacity Tester
• Checks battery condition in seconds
while the battery is in service
• Simultaneously measures
battery resistance and voltage
• Built-in datalogger stores up to
999 tests
• Four terminal Kelvin
measurements
• Resolution to 100μΩ
• 20V test voltage
• Large LCD display
• Invalid test indicators
• Auto-Hold and Auto-Off features
• Built-in water resistant case
with shoulder strap
BT100
380580
SPECIFICATIONS
Range
Resolution
Current
Accuracy
0.1mΩ
100mA
±(0.5% +2d)
2000mΩ
1mΩ
100mA
±(0.5% +2d)
20Ω
0.01Ω
10mA
±(0.5% +2d)
200Ω
0.1Ω
10mA
±(0.5% +2d)
2000Ω
1Ω
100mA
±(0.5% +2d)
200mΩ
Dimensions:
9.8 x 7.5 x 4.3" (250x19x110mm)
SPECIFICATIONS
Resistance Ranges: 40mΩ, 400mΩ, 4Ω, 40Ω
Resistance Accuracy: ±(1% reading + 8 digits)
Voltage Ranges:
4V, 40V
Voltage Accuracy:
±(0.1% reading + 6 digits)
Display:
4000 count LCD, dual readout
Input Voltage:
50VDC max.
Battery Life:
7 hours
Dimensions:
9.75" x 4" x 1.75" (250 x 100 x 45 mm)
ORDERING INFORMATION
EX/380580
EX/BT100
EX/BT102
Battery Powered Milliohm Meter
Battery Capacity Tester
120V AC Adapter for BT100
174
TEST
EQUIPMENT
Complete with AA batteries, leads with 4
alligator clips, leads with 2 Kelvin alligator clips
Includes PC interface cable, software, test leads
and AAA batteries
Amprobe Testers
NEW
SOLAR POWER METER
SWIVEL CLAMP METERS
• Measures Solar Power and
Transmission
• 180° Rotating Head
• Reads up to 2000 W/m2 or
634 BTU/(ft2 x h)
• Measure to 400A AC, 600V AC/DC
• Large Display & Separate Sensor
• One Hand Operation
• Displays Transmission Percentage
• Auto & Manual Ranging
• MAX/MIN & Data Hold
• Non-Contact Voltage Detection
SPECIFICATIONS
1999 W/m2, 634 BTU/(ft2 x h)
3½ digits, 2000 counts
Approx 0.25 second
Typically within ±10W/m2 [±3 BTU/(ft2 x h)] or
±5%, whichever is greater in sunlight
Angular Accuracy:
Cosine corrected < 5% for angles < 60º
Battery:
9V alkaline included
Operating Temperature: 5-40ºC (41-104ºF),<80%RH (non-condensing)
Dimensions:
5.2" × 2.4" × 1.5" (132×60×38 mm)
Measurement Range:
Display:
Sampling Time:
Accuracy:
PSYCHROMETER
• Temperature, RH, Dew Point &
Wet Bulb Measurements
• Extended Flex Probe
• Dual Display with Backlight
DC Volts Ranges:
Accuracy:
AC Volts Ranges:
Accuracy:
AC Current Ranges:
Accuracy:
Resistance Ranges:
Accuracy:
Continuity:
Non-Contact Voltage:
Other Features:
Display:
Temperature:
Power (Life):
Wire Diameter:
Dimensions:
Rating:
Included:
400mV, 4V, 40V, 400V, 600V
±(0.5% rdg + 2 dgts)
4V, 40V, 400V, 600V (50-500Hz)
±(1.2% rdg + 5 dgts), [1.5% on 600V range]
40A, 400A (50-60Hz)
±(2.0% rdg + 6 dgts)
400Ω, 4kΩ, 40kΩ, 400kΩ, 4MΩ, 40MΩ
±(1.0% rdg + 4 dgts) on 400Ω to 400kΩ ranges
Audible indication less than 25Ω
Beeper & red LED for 70V to 600VAC (50-60Hz)
Diode test, display hold, auto power off, noise filter
3¾ digit LCD, maximum reading 3999
0 to 50°C (32 to 122°F) operating, <70% RH
2 AAA batteries (alkaline 400 hrs)
1.18" (30mm) max.
12" × 5.3" × 1.2" (306×135×30 mm)
CAT III 600V
Battery, test leads, carrying case
CAT IV ANALOG CLAMP METERS
• Measure to 1000A & 600V AC
• MAX/MIN & Data Hold
• Tripod Mountable
ACD-20SW
SPECIFICATIONS
SOLAR-100
Optimize the placement of solar systems and verify window efficiency.
• Resistance, Capacitance, Continuity
• Resistance & Continuity
THWD-5
• Pointer Lock for Data Hold
SPECIFICATIONS
RH: 0 to 100%
Temperature: -10 to 60°C (14 to 140°F)
DP: -73.4 to 59.9°C (-100 to 139.8°F)
WB: -13.4 to 59.9°C (7.88 to 139.8°F)
Accuracy:
RH: ±3% from 10 to 90% at 25°C and ±5% for others
Temperature: ±0.6°C (±1°F)
Response Time: 60 seconds
Resolution:
0.1°C / 0.1°F
Temperature:
0 to 50°C (32 to 122°F) operating, up to 100% RH
Battery (Life):
Four AAA (100 hrs w/o backlight, 50 hrs w. backlight)
Dimensions:
6.9" × 2.8" × 1.3" (175×70×33 mm)
Included:
Hard carrying case, batteries, probe
• Operates Down to 5° F
Range:
NON-CONTACT AC VOLTAGE DETECTOR
• Visual & Audible Indication
• Measure to 122kV
• Self-test Verification
TIC 300 PRO
• Drop Proof to 6 ft
SPECIFICATIONS
Voltage Range:
30-1500 VAC
1500- 122,000 VAC (with Hot Stick TIC 410A)
Detection Range (typical): 2.7" @ 30 V, 18" @ 120 V, 28" @ 220 V,
50" @ 500 V, 75" @ 1000 V, 93" @ 1500 V
with Hot Stick: 1' 2" @ 1.5 kV, 2' 5" @ 2 kV, 6' 3" @ 10 kV,
9' 4" @ 25 kV, 14' 8" @ 75 kV, 22' @ 122 kV
174a
• No Batteries Needed for Volts & Amps
RS-3 PRO
SPECIFICATIONS
Display:
AC Voltage Ranges:
Input Impedance:
AC Amp Ranges:
Accuracy:
Ohms Range:
Accuracy:
Max. Wire Diameter:
Power:
Temperature:
Dimensions:
Safety LVD Rating:
Analog scales with clamping needle
150 / 300 / 600 Vrms
1.5 MΩ
6 /15 /40 /100 / 600 Arms [1000 A on RS-1007 PRO]
± 3% of Full Scale for Volts & Amps (50/60 Hz)
1000Ω, 25Ω mid-scale
± 3 degrees of arc
1.64" (41mm) [1.88" (47mm) on RS-1007 PRO]
One AAA battery for resistance & continuity
-15 to 50°C (-5 to 122°F) operating, <80% RH
RS-3 PRO: 10.3" × 4.0" × 1.6" (243×102×41 mm)
CAT IV 600V AC
ORDERING INFORMATION
AB/SOLAR-100
AB/THWD-5
AB/TIC 300 PRO
AB/TIC 410A
AB/ACD-20SW
AB/ACD-21SW
AB/RS-3 PRO
AB/RS-1007 PRO
Solar Power Meter
Temperature, RH, Dew Point & Wet Bulb Meter
Non-Contact AC Voltage Detector
Hot Stick Accessory for TIC 300 Pro (1.5-122 kV)
400A Swivel Clamp Meter
400A Swivel Clamp Meter w/ Temperature & Capacitance
CAT IV 600A Analog Clamp Meter
CAT IV 1000A Analog Clamp Meter
Hioki Testers
MULTI-FUNCTION DMMS
VOLTAGE DETECTOR
AC/DC Voltage & Current
Resistance & Continuity
9999 count LCD display
Min/Max, Average &
Relative values
• 4-20 mA measurement
converts to 0-100% display
• Optional RS-232C package
for PC data transfer
L
•
•
•
•
3804
L
4 ranges, 999.9mV to 999.9V (±0.3% rdg ±2d)
4 ranges, 999.9mV to 999.9V (±1.2% rdg ±5d) 40-500Hz
6 ranges, 400.0Ω to 40.00MΩ (±0.6 % rdg. ±3d)
6 ranges, 400.0µA to 10.00A (±0.2 % rdg. ±3d)
6 ranges, 400.0µA to 10.00A (±1.2 % rdg. ±5d) 50-2kHz
Capacitance, Data hold, continuity (<10Ω), diode check
3805: TRMS AC, freq to 50kHz, J&K thermocouples
Auto or Manual
41 segment
3/sec (digital), 13/sec (bar)
3" x 6.6" x 1.3" (76x167x33mm)
Test leads 3851-10, holster, battery
Ranging:
Bar Display:
Sample Rate:
Dimensions:
Accessories:
Voltage Range:
Indication:
Battery Check:
Operating Temperature:
Standards:
Dimensions:
• Slim Body for Easy
Clamping in Narrow
Spaces
• Independent-opening
Double-lever Jaw
• Right or Left
Hand Operation
• 4199 Count LCD
• True RMS Measurement
(3280-20)
4-Digit DMM
4-Digit TRMS DMM
SPECIFICATIONS
Function
AC Amps:
3129
SPECIFICATIONS
Detection Method:
Voltage Range:
Max. Wire Size:
Standards:
Dimensions:
Lead Length:
Electrostatic induction
70-600VAC, 50/60Hz
0.67" (17mm) dia., insulated wire
Cat III, 600V
2.76"W x 2.95"H x 1.18"D
27" (0.7mm)
ORDERING INFORMATION
HK/3120
HK/3129
HK/3246
HK/3280-10
HK/3280-20
175
Voltage Detector, batteries included
Phase Detector, with carrying case & AA batteries
Pencil HiTester, battery included
Clamp-On HiTester, with leads, battery & carrying case
TRMS Clamp-On HiTester, with leads, battery & carrying case
®
3280-20
L
TEST
EQUIPMENT
L
PHASE DETECTOR
• LED & Buzzer Indicate
Phase Direction
• No Electrical Connection
• Live Wire Check
(R-S, S-T)
• Battery Check &
Auto Shut Off
70-600VAC, 50/60Hz
Red LED and continuous beep
Green LED
0 to 40˚C, <80%RH (non-condensing)
CAT IV 600V, indoor use
5.9"L x 0.7"dia (149 x 18.5mm)
CLAMP-ON HITESTERS
ORDERING INFORMATION
HK/3804-50
HK/3805-50
• Detect AC Voltage in
Insulated Wires
SPECIFICATIONS
SPECIFICATIONS
DC Volts:
AC Volts:
Ohms:
DC Current:
AC Current:
Other Functions:
3120
DC Volts:
AC Volts:
Ohms:
Continuity:
Wire Size:
Allowable Current:
Overload Protection:
Operating Temperature:
Standards:
Dimensions:
Range (Accuracy)
3280-10: 42 / 420 / 1000A (50/60Hz;
±1.5% rdg ±5 d), 3280-20: 42 / 420/ 1000A
(45-66Hz: ±1.5% rdg ±5d)
(40-45Hz or 66Hz- 1kHz: ±2.0% rdg ±5d)
420m / 4.2 / 42 / 420 / 600V
(±1.3%rdg ±4d)
4.2 / 42 / 420 / 600V
(50-500Hz, ±2.3%rdg ±8d)
420 / 4.2k / 42k / 420kΩ (±2.0% rdg ±4d),
4.2MΩ (±5.0 rdg ±4d), 42MΩ (±10.0% rdg ±4d)
420Ω (±2.0% rdg ±6d), buzzer <50Ω
1.3" (33mm) max diameter
2000A AC rms max continuous
DCV/ACV: 600V DC/AC rms; Ω/Continuity:
250V DC/AC rms
0 to 40˚C, <80%RH (non-condensing)
CAT III 600V(AC A), CAT II 600V(AC/DC V)
2.2"W x 6.9"H x 0.6"D
Hioki Testers
NEW
INFRARED THERMO HITESTER
TRMS AC CLAMP METER WITH LEAKAGE
• Pistol Style with Backlit LCD
• Laser Aiming Marker
• Selectable °F/°C
• Min/Max Function
• Upper/Lower Alarm Settings
• Stores 50 Measurements
3283
Also in
HPK-1 Kit
• Measure to 200A TRMS AC
• Leakage with 10μA Resolution
• Recorder/Waveform Output
• Min/Max & Display Hold
• Switchable Filter
3419-20
SPECIFICATIONS
Measurement Range:
Display Resolution:
Wavelength:
Emissivity:
Field of View:
Sighting:
Accuracy:
Battery (Life):
Operating Temperature:
Dimensions:
-35 to 500 °C (-31 to 932 °F)
0.1 °C (0.2 °F)
6 to 14 μm
0.17 to 1.00 by steps of 0.01
8 : 1 distance to spot
Red laser marker, 1 mW (class 2)
-35.0 to -0.1°C : ± 10 % rdg. ± 2 °C
0.0 to 100.0°C : ± 2 °C
100.1 to 500.0°C : ± 2 % rdg.
9V alkaline (80 hrs with laser & backlight off)
0-50°C (32-122°F), <80%RH (non-condensating)
1.81" × 6.77" × 4.65" (46×172×118 mm)
LAN TESTER
SPECIFICATIONS
AC Amps:
Accuracy (50/60Hz):
Frequency Response:
Frequency Measure:
Switchable Filter:
Analog Output:
Display:
Sampling Rate:
Crest Factor:
Circuit Voltage:
Power:
Wire Dia.:
Dimensions:
Rating:
10.00 mA to 200 A, 5 ranges
±1.0 % rdg. ±5 dgt. (1.5 % on 200 A range)
40 Hz to 2 kHz (on AC Amps)
100.0 or 1000 Hz, 2 ranges (±0.3 % rdg. ±1 dgt.)
180 Hz ±30 Hz /-3 dB
1 V /f.s, DC or AC mode
1000 count digital, 35 segment bargraph
2 or 4 times/sec (Slow: 1 time/3 sec)
2.5 (1.5 on 200 A range)
300 V AC rms max. (insulated wire)
9V battery or AC adapter
Ø 40 mm (1.57") max.
2.44" × 8.86" × 1.54" (62×225×39 mm)
CAT III 300V
TRMS AC CLAMP METER
• 1000A & 600V TRMS AC
• Ohms, Frequency & Continuity
• Waveform Distortion Check
• Inrush Peak Capture
• Min/Max & Display Hold
• Verify Wire Destinations
• Detect Split Pairs
• Measure Cable Length
• Check Wire & Shield Condition
3665-10
3282
SPECIFICATIONS
Cable Types:
Connectors:
Errors Detected:
Cable Length:
Direction Check:
Display:
Switch:
Battery (Life):
Dimensions:
Twisted-pair, 100Ω shielded/unshielded, CAT 3, 4, 5, 5e, 6
RJ-45 plugs
Open, short, reversed, transposed, split pairs & miswires
2-300 m, (6.6-984 ft) with 0.1 m (0.3 ft) resolution
Up to 21 cables can be identified using the supplied 9690
terminator & optional 9690-01 to 9690-04
LCD with backlight & beeper
Select between meters or feet
Two AA (50 hours)
3.4" × 5.2" × 1.3" (85×130×33 mm)
PENCIL DMM
3246
• Backlit 4199 Count LCD • Data Hold, Continuity Beeper
• Auto or Manual Ranging • Pushbutton Penlight
SPECIFICATIONS
DC Volts:
AC Volts (50-500Hz):
Ohms:
Rating:
Dimensions:
420m / 4.2 / 42 / 420 / 600V (±1.3 % rdg ± 4d)
4.2 / 42 / 420 / 600V (±2.3 % rdg ±8d)
420 / 4.2k / 42k / 420k / 4.2M / 42MΩ
(±2.0 % rdg ±4d), plus diode check
CAT III 600 V
1.2" × 1.0" × 7.2" (31×26×84 mm)
SPECIFICATIONS
AC Amps:
AC Volts (50/60Hz):
Frequency Response:
Frequency Measure:
Resistance Measure:
Temperature Measure:
Display:
Sampling Rate:
Crest Factor:
Circuit Voltage:
Power:
Wire Dia.:
Dimensions:
Rating:
30.00 / 300.0 / 1000 A (±1.0% rdg. ±5 dgt)
300.0 / 600 V (±1.0 % rdg. ±3 dgt.)
40 Hz to 1 kHz (on AC Amps/Volts)
100.0 or 1000 Hz (±0.3 % rdg. ±1 dgt.)
1k & 10k ranges
-50 to 150 °C (with Probe 9462, sold separately)
3000 count digital, 35 segment bargraph
2 or 4 times/sec (Slow: 1 time/3 sec)
2.5 (1.7 on 1000 A or 600 V range)
300 V AC rms max. (insulated wire)
9V battery (45 hours)
Ø 46 mm (1.8") max.
2.44" × 9.06" × 1.54" (62×230×39 mm)
CAT III 1000V, CAT IV 600V
ORDERING INFORMATION
HK/3246
HK/3282
HK/3283
HK/3419-20
HK/3665-10
HK/HPK-1
Pencil DMM, battery included
TRMS AC Clamp Meter
TRMS AC Clamp Meter & Leakage Tester, with case & strap
Infrared Thermo HiTester, with carrying case
LAN Tester, with carrying case & 9690 Terminator
HVAC/Electrical Contractor Kit (includes 3120 Voltage Probe,
3280-10 Clamp-on Meter, 3419-20 IR Tester, 3804 DMM)
175a
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement