alinco, inc. - Maas Elektronik
A1.0-13/01
ALINCO, INC.
Yodoyabashi Dai-bldg 13F
4-4-9 Koraibashi, Chuo-ku, Osaka 541-0043 Japan
Phone: +81-6-7636-2362 Fax: +81-6-6208-3802
http://www.alinco.com
E-mail:[email protected]
VHF FM Transceiver / 136.000-173.995MHz
All EU and EFTA member states. Operator
license is required.
Copyright Alinco, lnc. PS0663/FNEG-EN
Printed in China
VHF FM Transceiver
DJ-100
Instruction Manual
Thank you for purchasing your new Alinco transceiver. Please read this manual
carefully before using the product to ensure full performance, and keep this
manual for future reference as it contains information on after-sales service.
In case addendum or errata sheets are included with this product, please read
those materials and keep them together with this instruction manual for future
reference.
Introduction
Thank you very much for purchasing this excellent Alinco transceiver. Our products are ranked among the
finest in the world. This radio has been manufactured with state of the art technology and it has been tested
carefully at our factory. It is designed to operate to your satisfaction for many years under normal use.
Please read this manual completely from the first page to the last, to learn all the functions the
product offers. It is important to note that some of the operations may be explained in relation
to information in previous chapters. By reading just one part of the manual, you may risk not
understanding the complete explanation of the function. In addition, please understand that
your radio may be programmed by the dealer according to the local regulation, masking some of
features mentioned in this manual.Please consult your dealer for details of programming.
Before transmitting
There are many radio stations operating in proximity to the frequency ranges this product covers. Be
careful not to cause interference when transmitting around such radio stations.
■ Lightning
Any person is not safe outdoor during thunderstorm and lightning. This condition is getting worse if
somebody keeps a hand-held radio; chances of being hit by lightning are doubled since lightning may
hit a radio antenna as well. At this time, there is no hand-held radio having any kind of protection against
lightning current (which is higher than10 kA.). Note also that no car provides adequate protection of its
passengers or drivers against lightning as well. Therefore, Alinco will not take responsibility for any danger
associated with using its hand-held radios outdoor or inside the car during lightning.
■ About
IP54 rating / Dust and splash resistant
About IP54 rating
5: Dust protected /Ingress of dust is not entirely prevented, but it must not enter in sufficient quantity to
interfere with the satisfactory operation of the equipment; complete protection against contact.
4: Splashing water / Water splashing against the enclosure from any direction shall have no harmful effect.
Test duration: 5 minutes / Water volume: 10 litters per minute /Pressure: 80~100 kN/m²
The IP54 designation provides for limited dust and splash proofing of the radio per specified above. This
compatibility is factory guaranteed for a period of one year provided all the jack covers are securely in
place, any accessories connected must be specified genuine Alinco accessories and the radio has not
been disassembled by the customer. The factory has tested and made the equipment compatible to IP54
certification during engineering. However, please understand that this equipment is NOT certified IP54
compliant but is designed to remain operational when used in hard conditions and is in no way stating
that you should attempt to wash the radio for cleaning. Warranty will not cover radios that are water/dust
damage due to negligence or misuse of the product.
■ Covering
ranges
You may expect a range of approx.3km/2 miles or more at high-power when located on a flat, noise-free
place like on a beach.However,it may vary drastically depending on how to wear and carry the radios,
surrounding locations/conditions and static noise levels (below or near power transmission lines), etc. In
urban areas with many buildings or inside a building, such covering range will become drastically short
even to several tens of meters.
Features
■ Output power selectable 5W/2W/0.5W
■ 200 PC-programmable channels
■ Li-Ion battery pack and stand-charger as standard accessories
■ Alphanumeric name tags
■ FM broadcast 76-108MHz receiver built-in
■ Selectable Battery-save parameters
■ Busy Channel Lockout
■ Voice Compander (Reduce Noise & enhance audio clarity)
■ Inversion Scramble(Analog encryption)
■ CTCSS/DCS Encode/Decode, DTMF/ANI, 5-Tone, 2-Tone and Tone-bursts
■ VOX built-in
■ Emergency Kill/Stun/Revive, Alarm signal, Various scan modes, Key lock, Wide/
Narrow operations and more at NO extra costs.
Conformity Symbols
Tested to comply MIL-STD-810G
-Shock: Method 514.6/I,IV -Vibration: Method 516.6/I
SAFETY TRAINING INFORMATION
Warning: Please Read Carefully
A transceiver generates RF (Radio Frequency) electromagnetic energy while transmitting. This Alinco
transceiver is designed for and classified as “Occupational Use Only", meaning it must be used minimum
necessary only during the course of employment by employees aware of the hazards, and the ways
to minimize such hazards. This transceiver is NOT intended for use by the “General Population” in an
uncontrolled environment. This transceiver has been required “SAR-Standard” tested and complies with
the FCC RF exposure limits for “Occupational Use Only”.
To ensure that your expose to RF electromagnetic energy is within the allowable limits for occupational
use, always adhere to the following guidelines:
• DO NOT operate the transceiver without a proper antenna attached, as it may damage the transceiver
and may also cause you to exceed FCC RF exposure limits. A proper antenna is the genuine antenna
supplied with this transceiver by Alinco or ones specifically authorized by the antenna manufacturer for
use with this transceiver.
•
DO NOT transmit for more than 50% during the time of employment (50% duty cycle or less).
Transmitting excessive amount of time can cause RF exposure compliance requirements to be
exceeded. Please carefully read this instruction manual to learn how to transmit and stop transmitting
before starting to use it.
• ALWAYS keep the antenna at least 3 cm (1 inch) away from your body when transmitting and only use
the original belt clips when attaching the transceiver to your body (Unauthorized attachment devices may
help radiating more electromagnetic energy). To obtain the best sound quality during communications,
hold the antenna at least 6 cm (2 inches) from your mouth, and slightly off to one side.
• Use only the genuine Alinco accessories listed in this instruction manual for RF safety. Third party
accessories are not guaranteed for RF safety by Alinco.
The above provides the information needed to make users of this transceiver aware of RF exposure, and
what to do to assure that this transceiver operates with the FCC RF exposure limits.
• Electromagnetic Interference/Compatibility
During transmissions, a transceiver generates RF energy that can possibly cause interference with other
devices and/or systems.
To avoid such interference, turn off the transceiver in areas where signs are posted to do so. NEVER
operate transceivers in areas that are sensitive to electromagnetic radiation such as hospitals, blasting
sites, aboard aircraft and similar advanced vehicles etc. Do not expose magnetic cards such as credit
cards in a very close vicinity to a transceiver; it may erase the magnetic data. A person using medical
devices such as a pacemaker MUST NOT use this transceiver, as interference may cause malfunction to
such medical devices.
• Occupational/Controlled Use
This product is used in situations that users are exposed to RF as consequence of their employment
provided those users are fully aware of the potential RF hazards and can exercise control over their
exposure.
•
•
This transceiver is NOT ATEX approved and NOT intended for the use in hazardous explosive
atmospheres.
California residents only: Please note per Proposition 65 that Li-Ion battery pack in this product
may contain chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm.
FCC INFORMATION
FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
●● Reorient or relocate the receiving antenna.
●● ncrease the separation between the equipment and receiver.
●● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
●● Consult the dealer or an experienced radio/TV technician for help.
For Customers in Canada :
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Alert
Environment and condition of use
It is recommended that you check local traffic regulations regarding the use of a radio equipment while
driving. Some countries prohibit or apply restrictions for the operation of radios and mobile- phones while
driving.
Do not use this product in close proximity to other electronic devices, especially medical ones. It may
cause interference to those devices.
Keep the radio out of the reach of children.
In case a liquid leaks from the product, do not touch it. It may damage your skin. Rinse with plenty of cold
water if the liquid contacted your skin.
Never operate this product in facilities where radio products are prohibited for use such as aboard aircraft,
in airports, in ports, within or near the operating area of business wireless stations or their relay stations.
Use of this product may be prohibited or illegal outside of your country. Be informed in advance when you
travel.
The manufacturer declines any responsibilities against loss of life and/or a property due to a failure of this
product when used to perform important tasks like life-guarding, surveillance, and rescue.
Do not use multiple radios in very close proximity.
product(s).
It may cause interference and/or damage to the
Risk of explosion if battery is replaced with an incorrect type. Dispose of, or recycle used batteries
according to your local regulations.
The manufacturer declines any responsibilities against loss of life and property due to a failure of this product
when used with or as a part of a device made by third parties.
Use of third party accessory may result in damage to this product. It will void our warranty for repair.
Handling this product
Be sure to reduce the audio output level to minimum before using an earphone or a headset. Excessive
audio may damage hearing.
Do not open the unit without permission or instruction from the manufacturer. Unauthorized modification or
repair may result in electric shock, fire and/or malfunction and voids warranty.
Do not operate this product in a wet place such as in a shower room. It may result in electric shock, fire and/
or malfunction, This product is splash-proof but not a complete water-proof.
Do not place the product in a container carrying conductive materials, such as water or metal in close
proximity. A short-circuit to the product may result in electric shock, fire and/or malfunction.
About chargers
Do not use adapters other than having the specified voltage. It may result in electric shock, fire and/or
malfunction,Never turn on the radio while charging.
Do not plug multiple devices using an adapter into a single wall outlet. It may result in overheating and/or fire.
Do not handle adapter with a wet hand. It may result in electric shock.
Securely plug the adapter into the wall outlet. Insecure installation may result in short-circuit, electronic shock
and/or fire.
Do not use the adapter if the plug or socket contacts are dirty. Overheating and/or short-circuiting may result
in fire, electric shock and/or damage to the product.
In case of emergency
In case of the following situation(s), please turn off the product, switch off the source of power,
then remove or unplug the power-cord. Please contact your local dealer of this product for service
and assistance. Do not use the product until the trouble is resolved. Do not try to troubleshoot the
problem by yourself.
●● When a strange sound, smoke and/or strange odor comes out of the product.
●● When the product is dropped or the case is broken or cracked.
●● When a liquid penetrated inside.
●● When a power cord (including DC cables, AC cables and adapters) is damaged
For your safety, turn off then remove all related AC lines to the product and its accessories from the wall outlet
if a thunderstorm is likely.
Maintenance
Do not open the unit and its accessories. Please consult with your local dealer of this product for service and
assistance
Alert
Environment and condition of use
Do not use the product in proximity to a TV or a radio. It may cause interference or receive interference.
Do not install in a humid, dusty or insufficiently ventilated place. It may result in electric shock, fire and/or
malfunction.
Do not install in an unstable or vibrating position. It may result in electric shock, fire and/or malfunction when/
if the product falls to the ground.
Do not install the product in proximity to a source of heat and humidity such as a heater or a stove. Avoid
placing the unit in direct sunlight.
Be cautious of a dew formation. Please completely dry the product before use when it happens.
About transceiver
Be cautious of the whip antenna when carried in your shirt-pocket etc. It may make contact with your eye and
cause injury.
Do not connect devices other than specified ones to the jacks and ports on the product. It may result in
damage to the devices.
Turn off and remove the power source (AC cable, DC cable, battery, cigar cable, charger adapter etc.) from
the product when the product is not in use for extended period of time or in case of maintenance.
Never pull the cord alone when you unplug AC cable form the wall outlet.
Use a clean, dry cloth to wipe off dirt and condensation from the surface of the product. Never use thinner or
benzene for cleaning.
Check with your local waste officials for details on recycling or proper disposal in your area.
PC PROGRAMMING
NOTE: The utility software may be available to distributors/dealers only. USB programming cable is required. The
manufacturer will not release the software to unauthorized party so please contact your dealer for details.
This product may be blocked for operation in default state and only dealers can program to make it working.
Manufacturer is not available for reprogramming or modifying the dealer-programmed setting. VFO(frequnecy) mode
may not be available due to regulation.
Please consult your dealer for technical supports of this product.
TABLE OF CONTENTS
STANDARD ACCESSORIES�����������������������������������������������������������������������������������������������������������������������������������������01
Standard Accessories������������������������������������������������������������������������������������������������������������������������������������������������01
KEY OPERATIONS / QUICK CHART���������������������������������������������������������������������������������������������������������������������������02
BATTERY INFORMATION���������������������������������������������������������������������������������������������������������������������������������������������03
Charging Operation....................................................................................................................................................03
Battery Charger Type..................................................................................................................................................03
Notice for Charging Battery����������������������������������������������������������������������������������������������������������������������������������������03
How to Charge the battery pack���������������������������������������������������������������������������������������������������������������������������������05
How to Store the Battery��������������������������������������������������������������������������������������������������������������������������������������������07
Installing / Removing the Li-ion Battery����������������������������������������������������������������������������������������������������������������������07
Installing / Removing the Antenna������������������������������������������������������������������������������������������������������������������������������08
Installing / Removing the Belt Clip�����������������������������������������������������������������������������������������������������������������������������08
Accessories����������������������������������������������������������������������������������������������������������������������������������������������������������������09
Installing the Hand Strap��������������������������������������������������������������������������������������������������������������������������������������������09
GETTING ACQUAINTED�����������������������������������������������������������������������������������������������������������������������������������������������10
LCD Display���������������������������������������������������������������������������������������������������������������������������������������������������������������10
Front Panel�����������������������������������������������������������������������������������������������������������������������������������������������������������������11
Side Panel������������������������������������������������������������������������������������������������������������������������������������������������������������������12
BASIC OPERATIONS����������������������������������������������������������������������������������������������������������������������������������������������������13
Power On and off�������������������������������������������������������������������������������������������������������������������������������������������������������13
Adjusting Audio output level���������������������������������������������������������������������������������������������������������������������������������������13
Frequency Input by Keypad���������������������������������������������������������������������������������������������������������������������������������������14
Channel Input by Keypad�������������������������������������������������������������������������������������������������������������������������������������������14
Change Frequency / Channel Through Main Dial������������������������������������������������������������������������������������������������������15
Alarm��������������������������������������������������������������������������������������������������������������������������������������������������������������������������15
Squelch Off Momentary/ Squelch Off�������������������������������������������������������������������������������������������������������������������������15
Receiving�������������������������������������������������������������������������������������������������������������������������������������������������������������������16
Professional
FM Transceiver
I
TABLE OF CONTENTS
Transmitting���������������������������������������������������������������������������������������������������������������������������������������������������������������16
[PF1] Key Function ����������������������������������������������������������������������������������������������������������������������������������������������������16
Side [PF2] Key Function��������������������������������������������������������������������������������������������������������������������������������������������17
Switching between VFO and Memory Mode��������������������������������������������������������������������������������������������������������������17
ADVANCED OPERATIONS�������������������������������������������������������������������������������������������������������������������������������������������18
Channel Edit���������������������������������������������������������������������������������������������������������������������������������������������������������������18
Delete Channel����������������������������������������������������������������������������������������������������������������������������������������������������������18
FM Radior Receiver���������������������������������������������������������������������������������������������������������������������������������������������������18
Add or Cancel DTMF, 2TONE, 5TONE, FSK Signaling���������������������������������������������������������������������������������������������19
CTCSS / DCS Scan���������������������������������������������������������������������������������������������������������������������������������������������������20
Add or cancel CTCSS/DCS���������������������������������������������������������������������������������������������������������������������������������������21
Frequency Scan, Channel Scan or FM Search����������������������������������������������������������������������������������������������������������21
Scan Channel Skip�����������������������������������������������������������������������������������������������������������������������������������������������������22
Priority Monitor�����������������������������������������������������������������������������������������������������������������������������������������������������������23
TX Power Selection����������������������������������������������������������������������������������������������������������������������������������������������������23
FSK Message Single Transmitting�����������������������������������������������������������������������������������������������������������������������������24
FSK Message Group Transmitting�����������������������������������������������������������������������������������������������������������������������������24
FSK Message All Transmitting�����������������������������������������������������������������������������������������������������������������������������������25
FSK message checking���������������������������������������������������������������������������������������������������������������������������������������������25
DTMF Code Searching And Setup�����������������������������������������������������������������������������������������������������������������������������26
Manually Transmitting DTMF Signaling���������������������������������������������������������������������������������������������������������������������26
Remotely Kill/ Revive�������������������������������������������������������������������������������������������������������������������������������������������������26
Remotely Stun /Waken����������������������������������������������������������������������������������������������������������������������������������������������27
RF Attenuator (ATT)��������������������������������������������������������������������������������������������������������������������������������������������������27
CHANNEL OPERATIONS..............................................................................................................................................28
CTCSS / DCS Encode Setup�������������������������������������������������������������������������������������������������������������������������������������28
CTCSS/DCS Decode ������������������������������������������������������������������������������������������������������������������������������������������������29
II
Professional
FM Transceiver
TABLE OF CONTENTS
Choose To Transmit 2TONE��������������������������������������������������������������������������������������������������������������������������������������29
Choose To Transmit 5TONE��������������������������������������������������������������������������������������������������������������������������������������30
Choose To Transmit FSK�������������������������������������������������������������������������������������������������������������������������������������������30
Signaling Combination ����������������������������������������������������������������������������������������������������������������������������������������������31
Frequency Step ���������������������������������������������������������������������������������������������������������������������������������������������������������32
Offset Direction����������������������������������������������������������������������������������������������������������������������������������������������������������32
Offset Frequency��������������������������������������������������������������������������������������������������������������������������������������������������������33
Wide/ Narrow FM Mode���������������������������������������������������������������������������������������������������������������������������������������������33
Frequency Reverse����������������������������������������������������������������������������������������������������������������������������������������������������34
Talk Around ���������������������������������������������������������������������������������������������������������������������������������������������������������������34
Busy Channel Lockout�����������������������������������������������������������������������������������������������������������������������������������������������35
Prohibits transmitting �������������������������������������������������������������������������������������������������������������������������������������������������35
Sub Channel Display Setup���������������������������������������������������������������������������������������������������������������������������������������36
Compander (Reduce Noise, Improve Communication Quality)���������������������������������������������������������������������������������36
Scrambler Setup (Encryption) �����������������������������������������������������������������������������������������������������������������������������������37
SET MODE OPERATIONS��������������������������������������������������������������������������������������������������������������������������������������������38
Beep and Voice assist sounds�����������������������������������������������������������������������������������������������������������������������������������38
Time-Out Timer����������������������������������������������������������������������������������������������������������������������������������������������������������38
Voice Operated Transmission (VOX) ������������������������������������������������������������������������������������������������������������������������39
Voice Operated Transmission (VOX) Delay Time �����������������������������������������������������������������������������������������������������40
Auto Power-Off�����������������������������������������������������������������������������������������������������������������������������������������������������������40
DTMF Burst and Pause timing�����������������������������������������������������������������������������������������������������������������������������������41
Squelch Level �����������������������������������������������������������������������������������������������������������������������������������������������������������41
Scan Resume Conditions�������������������������������������������������������������������������������������������������������������������������������������������42
Function Key Setting time������������������������������������������������������������������������������������������������������������������������������������������43
Backlight On/Off Mode ����������������������������������������������������������������������������������������������������������������������������������������������43
Backlight Color Setup�������������������������������������������������������������������������������������������������������������������������������������������������44
Professional
FM Transceiver
III
TABLE OF CONTENTS
Display Mode�������������������������������������������������������������������������������������������������������������������������������������������������������������45
DTMF Self ID display�������������������������������������������������������������������������������������������������������������������������������������������������45
5TONE Self ID Inquiry������������������������������������������������������������������������������������������������������������������������������������������������46
Tone-burst tone setting ����������������������������������������������������������������������������������������������������������������������������������������������46
Battery Save Ratio�����������������������������������������������������������������������������������������������������������������������������������������������������47
FM Radio��������������������������������������������������������������������������������������������������������������������������������������������������������������������48
Password�������������������������������������������������������������������������������������������������������������������������������������������������������������������48
Reset��������������������������������������������������������������������������������������������������������������������������������������������������������������������������49
DEFAULT SETTINGS����������������������������������������������������������������������������������������������������������������������������������������������������50
OPTIONAL ACCESSORIES������������������������������������������������������������������������������������������������������������������������������������������51
RECOMMENDED INSTALLATION OF EARPHONE MICROPHONE��������������������������������������������������������������������������52
AUXILIARY FUNCTIONS����������������������������������������������������������������������������������������������������������������������������������������������53
Cable Cloning.............................................................................................................................................................53
Communication Note..................................................................................................................................................53
TECHNICAL SPECIFICATIONS������������������������������������������������������������������������������������������������������������������������������������54
Technical Specifications.............................................................................................................................................54
TROUBLE SHOOTING GUIDE��������������������������������������������������������������������������������������������������������������������������������������56
APPENDIX���������������������������������������������������������������������������������������������������������������������������������������������������������������������58
CTCSS Frequency Chart�������������������������������������������������������������������������������������������������������������������������������������������58
1024 Groups DCS Chart��������������������������������������������������������������������������������������������������������������������������������������������59
IV Professional
FM Transceiver
STANDARD ACCESSORIES
Standard Accessories
Antenna
Battery
Belt Clip
Instruction
Manual
Charger
AC Adaptor
(A shape may vary)
Hand Strap
NOTE: Accessories may differ depending on the version you have purchased. Please contact your local
dealer for details of standard accessories and the warranty-policy before purchase.
Professional
FM Transceiver
01
KEY OPERATIONS / QUICK CHART
Function
02
FM radio On/Off
Key Operation
【A 】
【1 】
Add/delete Optional Signaling
【A 】
【2 】
CTCSS/DCS Scan
【A 】
【3 】
Add or delete CTCSS/DCS code
【A 】
【4 】
Scan
Scan skip
【A 】
【A 】
【5 】
【6 】
Priority Monitor
【A 】
【7 】
TX power selection
【A 】
【9 】
FSK transmit method
【A 】
【 】
FSK message checking
Hold pressing
Displays current data,"EMPTY" means no data
【 】key 1second
DTMF code inquir
【A 】
【0 】
Signal Annenuation
【A 】
【# 】
Keypad lock
Hold pressing【#】 When LCD displays "ATT " icon, Keypad is
locked.
key 1second
Professional
FM Transceiver
Parameter Instruction
Activate FM Broadcasting Receiver
Choose DTMF、2TONE、5TONE、FSK as
optional signaling of current channel
Scan CTCSS when channel set CTCSS
decode; Scan DCS when channel set DCS
Add or delete CTCSS encode/decode or DCS
encode/decode
Channel or frequency scan
In standby state, checking Priority channel
"H"icon: High power, "M" icon: Middle power,
"L" icon: Low Power
Press【B】key/【C】key to choose transmit
method:"CAL ID","CAL GR"or "CAL AL"
Displays received message, press【B】key
【C】key to change page
When LCD displays "ATT" icon, receiving
signal sensitivity reduces
When LCD displays "ATT " icon, Keypad is
locked.
Page
18
20
21
22
23
23
24
24
25
26
27
28
36
BATTERY INFORMATION
Charging Operation
The battery is not charged at the factory, so please charge it before use. Charge the battery for the first
time after purchase or extended storage (more than 2 months) may not bring the battery to its normal
operating capacity. After repeating fully charge/ discharge cycle for two or three times, the operating
capacity will reach the best performance. The battery life is over when its operating time decreases
even though it is fully and correctly charged and it must be replace to new one.
Battery Charger Type
Please use Alinco's designated charger, other models may cause explosion. After installing the battery,
when the radio displays
low battery, please charge the battery.
Notice for Charging Battery
▲Do not shortcircuit the charger. Never attempt to remove the casing from the battery, otherwise the
warranty is void and you risk serious damage to yourself and properties.
▲The ambient temperature should be between 5℃ and 40℃ while charging. Charging outside this
range may not charge the battery.
▲Always switch off the transceiver before charging. Otherwise, it may not charge correctly.
▲To avoid interfering the charging procedure, please do not cut off the power or take out the battery
during charging.
▲Do not recharge the battery if it is already fully charged. This may shorten the life of the battery or
damage the battery.
▲Do not charge the battery or transceiver when wet. Dry it before charging to avoid danger.
Professional
FM Transceiver
03
BATTERY INFORMATION
Caution
• Risk of explosion, generation of heat or leak of chemicals inside if the battery is replaced by an
incorrect type or reverse polarity. Use always the recommended types of batteries in this manual only.
• The battery pack isn't fully charged when shipped. It must be charged before use.
• Charging should be conducted in a temperature range of +5ºC to +40ºC (+41ºF to +104ºF).
• Don't modify, dismantle, incinerate or immerse the battery pack in the water as this can be dangerous.
• Never short-circuit the battery pack terminals, as this can cause damage to the equipment or lead to
heating of the battery which may cause burns.
• Unnecessary prolonged charging (overcharging) can deteriorate battery performance.
• The battery pack should be stored in a dry place where temperature is in -10ºC to +45ºC (-14ºF to
+113ºF) range. Temperatures outside this range can cause the battery liquid to leak. Exposure to
prolonged high humidity can cause corrosion of metal components.
• Battery-packs are a consuming part. When its operating time becomes considerably short after a
normal charge, please consider that the pack is exhausted and replace it with a new one.
• The battery pack is recyclable. Check with your local waste officials for details on recycling options or
proper disposal in your area.
• Use specified genuine chargers only to charge battery packs. Use of other chargers may cause
damage to products, you and your property.
• Never carry battery packs together with conductive articles such as metals in a same bag to prevent
from short-circuiting. Put the packs only in nylon bags to carry them safely.
• Even if you do not use the battery pack for a long time, charge it at least once every three months to
prevent deterioration.
04 Professional
FM Transceiver
BATTERY INFORMATION
How to Charge the battery pack
1.Plug the AC adaptor into the AC outlet, then plug into the
DC jack ,the indicator lights orange for 1 second and goes
out---waits to charge.
2.Slide the battery or transceiver with battery into the
charger; make sure the battery terminals are in contact
with the charging terminals . LED turns into twinkling RED
---pre-charging begins.
3.Pre-charging for about 5 minutes, LED twinkles stop then
charging begins.
4.It takes about 4 hours to fully charge the battery, and LED turns to green when the charge is complete.
Warning: Never charge while the radio is turned on. When turned on, the charger can't detect the
charging voltage properly and LED fails to indicate charge status correctly.
5. Charging Process:
Status
Stand-by (self-examine orange lights
1second when power on) ----------------------Pre-charging (pre-charging stage) ---------------Charging (charge in constant current.) ------------Fully charged (charge in constant voltage) -----------
LED
None
Red light twinkles for about 5 minutes
RED light lightens for about 4 hours
Green light
Professional
FM Transceiver
05
BATTERY INFORMATION
6. LED Indicator:
STATUS
LED
self-examine
Charge Fully
(No battery) Pre-charging
Trouble
normally Charged
when power on
Red blinks for 5
Red blinks
Orange
None
Red
Green
(for 1 second)
minutes
alternatively
NOTE:
▲ Trouble means battery heating, short-circuit or charger malfunction. Remove the battery pack from
the charger immediately and contact to your local dealer for services.
▲ The max trickle pre-charging time is 30 minutes. In case the red indicator continues to blink longer,
please stop charging and consult with your local dealer for services.
▲ It is known that Li-Ion battery packs heat up over 400℃ by itself when kept in a temperature of over
80℃ for extended period of time. Although the packs are protected against overheating with a protective
circuit, never leave the battery packs in a car or similar locations in hot seasons.
▲ Li-ion packs may deteriorate by over 30% regardless of conditions after 3 years. This is a nature of Liion pack and not a defect of the product.
▲ The charger is to charge the battery pack only. It is not an AC adapter to operate the radio. Never
attempt to transmit the radio with using the charger as it will cause the damage to the charger and a
repair/replace may become necessary.
▲ The charge should be conducted in an ambient temperature with a proper air-conditioning in an
extremely hot or cold seasons.
▲ Try charging the battery pack only when having trouble charging with the radio.In case the radio may
have troubles,the charge can't be conducted properly.If the battery pack can be charged alone, please take
the radio to your local dealer for services.
06 Professional
FM Transceiver
INSTALLATION & CONNECTION
How to Store the Battery
1.The battery should be kept in the status
of 50% discharge when storing.
2.It should be kept in cool, dry environment
and remove it from the transceiver.
3.Keep away from source of heat and
direct sunlight.
WARNING
Do notshort-circuit battery terminals.
Never attempt to remove the casing from the battery
pack.
Never assemble the battery hazardous in explosive
atmosphere as, spark may cause explosion.
Do not put the battery in hot environment or throw it
into fire, it may also cause explosion.
Note: Battery pack discharges faster when it is attached to the radio. Please always remove it from the
radio when not in use.
Installing / Removing the Li-ion Battery
1.Match the three grooves of the battery pack with the
corresponding guides on the back of the transceiver,
then push it.
2.Press the battery and transceiver firmly together until the
release latch on the top of the transceiver locks. After
hearing a“click”sounds, the battery has been locked.
3.To remove the battery, slide up the release latch and
remove the pack away from the transceiver.
Professional
FM Transceiver
07
INSTALLATION & CONNECTION
Installing / Removing the Antenna
Installing the Antenna:
1. Hold the antenna by its base.
2. Align the grooves at the base of the antenna with the protrusions on the
antenna connector.
3. Slide the antenna down and turn it clockwise until it stops.
4. Confirm that the antenna is securely connected. Check the connection from
time to time.
Removing the Antenna:
Turn the antenna counter-clockwise to disconnect the antenna.
Note: Do not use third-party antenna as it may radiate more RF
that exceeds SAR limit guidances.
Installing / Removing the Belt Clip
Installing the Belt Clip:
1. Put the belt clip on the back of the unit, and the screw clockwise until it stops.
2. Confirm that the belt clip is securely attached.
* Tighten up the screw occasionally.
Removing the Belt Clip:
Turn the screw counter-clockwise to remove the belt clip.
Caution: Use the screws of specified size only. Others may cause
damage to the product. screws (+PM2.5x3)
08 Professional
FM Transceiver
INSTALLATION & CONNECTION
Accessories
Remove the jack cover and insert the accessory
plug into the jack,as shown.
When the accessory is not used, please be sure
to put on cover with securely.
NOTE:
1.To keep the radio dust and splash resistant, the
cover must be closed properly with the original
supplied cover.
2.The radio is not dust and splash resistant while
using the optional accessory risking that the water
may penetrate inside through the plug.
Installing the Hand Strap
Attach the hand strap as shown.
Professional
FM Transceiver
09
GETTING ACQUAINTED
LCD Display
Please refer the chart below to understand the meanings of icons that appear on the LCD display.
Frequency Reverse
Offset direction
DCS
Talk Around
CTCSS
FUNC Icon
FM radio
TX Power
ATT
Busy Channel
NOTE:
Battery capacity indicator(full)
Battery power consuming
10 Professional
FM Transceiver
Priority Scan
VOX Function
Scan Skip
Narrow band
Scramble (Encryption)
Battery Capacity
Function Menu Serial
No. / Main Channel
No. serial No.
Keypad Lock
No power,replace battery pack or charge battery
Receiving signal strength / TX power
indicator
GETTING ACQUAINTED
Front Panel
Main dial
Antenna
Power / Volume Switch
TX/RX indicator, RX is Green,
TX is Red
Speaker
Microphone
LCD
A key/Function key
B key/Up key/Call key
Numeric keys
C key/Down key/V/M
D key, Exit key or channel/
VFO Exchange key
Professional
FM Transceiver
11
GETTING ACQUAINTED
Side Panel
Accessory and PC
programming port
PTT key
PF1 key (1 Primary Function key)
PF2 key (2 Primary Function key)
Belt Clip
Battery
Left Panel
12
Professional
FM Transceiver
Right Panel
BASIC OPERATIONS
Power On and off
Turn【POWER】/【VOLUME】dial clockwise to power on.
Turn it counterclockwise to power off.
Adjusting Audio output level
Press and hold [PF2] key to monitor white noise to refer to the current audio
level.
Turn【POWER】/【VOLUME】dial clockwise to increase the audio level,
counterclockwise to decrease.
CAUTION:
NEVER USE EARPHONE while adjusting audio level. The max audio output is 1W, and it’s loud
enough to hurt your eardrums.
You may feel a static shock when wearing an earphone in a dry atomosphere but it's not a defect of
product but a cause of nature.It is the same shock you feel typically when opening a door of a car in
certain conditions.
Professional
FM Transceiver
13
BASIC OPERATIONS
Frequency Input by Keypad
In VFO mode or FM radio receiver, You may directly enter frequency through numeric keys.
to switch to VFO.
1.Press
2.Enter the desired frequency in 6-digit by numeric keys.
Example: To enter 155.125, press [1][5][5][1][2][5]. By pressing the last [5], a dot appears after the
MHz unit and the radio is ready to operate. When an invalid frequnecy is entered, the display will return
to the current display.
NOTE:
In Frequency + Channel mode, it shows current channel number on the right of main frequency display.
The direct input is relevant to the stepping and transceiver frequency scope. If entering frequency is
beyond scope or not matching with step size, the input is invalid.
In the FM receiver mode, the frequency step size input by numeric keys is 50KHz
Channel Input by Keypad
In Frequency + Channel or Channel + Name Tag mode, you may select the channel by entering three
channel digits (000-199). If the entered channel has not been preprogrammed, the radio will beep to
alert you that input is wrong and then return to current channel.
14 Professional
FM Transceiver
BASIC OPERATIONS
Change Frequency / Channel Through Main Dial
Under frequency mode, you can change the current frequency to desired one through main dial; turn
clockwise to increase frequency; counter-clockwise turn to decrease, every click will increase/decrease
one step.
●● This transceiver has 9 step size: 5, 6.25, 8.33, 10, 12.5, 20, 25, 30 and 50 KHz, channel steps.
Under channel mode, you can change the current channel to desired one through main dial, turn
clockwise to the next channel, counter-clockwise turn to the last channel.
Alarm
When [PF1] key is set as alarm, press and hold this key to sound alarm and transmit, press again to
cancel.
●● Note: Please use programming software to choose the Alarm mode or close Alarm.
Squelch Off Momentary/ Squelch Off
When [PF2] key function set as "Squelch Off Momentary/ Squelch Off ", you can use this key to monitor
weak signals that you cannot hear during normal operation.
1.Squelch Off Momentary: press and hold [PF2] key to hear the background noise, release the key to
return to normal operation.
Professional
FM Transceiver
15
BASIC OPERATIONS
2. Squelch Off: press [PF2] key to hear the background noise, press [PF2] again to return
to normal operation.
●● Note: The above functions should be set in software. Manual setting is not available.
Receiving
Select the operating mode and frequency or channel that you wish to operate. When a signal is
received on the frequency that you selected, and S-meter is displayed on the LCD, then the received
signal can be heard. The RX indicator also lights green at this time.
●● Note: Please be aware of the squelch level and selective-calling settings such as CTCSS and DCS as you
may risk not hearing the receiving signal.
Transmitting
Select the frequency by using the dial or keypad.
2. Press the [PTT] key. The red TX indicator turns on while transmitting.
3. While holding down the [PTT] key, speak into the unit at normal voice from the distance of 5cm (2").
4. Release the [PTT] key to receive.
Before transmitting, it is recommended to monitor the channel you are going to use to ensure it is not
busy by pressing and holding [PF2] key.
[PF1] Key Function
The Side [PF1] key can realized functions as below:
1.In receiving mode, press to check current voltage.
16 Professional
FM Transceiver
BASIC OPERATIONS
2.In receiving mode, press and hold to alarm.(you can shut off this function by software)
3.In transmitting mode, press to transmitting selected Tone-pulse signaling.
4.Press this key to power on transceiver, and get into wire cloning mode.
Side Key [PF2] Function
Monitor function (squelch off or momentary off per preprogramming).
1. Turn the main dial while pressing and holding this key to set the squelch level.
2. While transmitting, press this key to transmit preprogrammed 2-tone,5-tone or DTMF tone signaling.
3. Pressing and holding this key while turning on for 2 seconds to enter to the parameter setting mode.
key pressed together to perform the factroy reset. All icons will appear
4. Turn on with this key and
then after 2 seconds the display resumes with showing 155.000,
●● Note: Reset may be prohibited by the dealer programming.
Switching between VFO and Memory Mode
In main channel, Sub channel or FM broadcast mode, press
mode (VFO) and Memory mode.
key to switch between frequency
●● Note: When the channel hasn’t been preprogrammed, this operation is unavailable. VFO mode may not
be available in some countries of distribution due to regulations.
Professional
FM Transceiver
17
����
�
���
�����
�����
ADVANSED OPERATIONS
●● Note: Most part of this ADVANSED OPERATION chapter is useless for preprogrammed radio users.
Channel Edit
1.In main channel frequency mode or sub-channel frequency mode, enter the frequency and signaling
as desired, after pressing
key, the top left corner of LCD displays " ", then press
, the
channel number twinkling means getting into store/ delete channel mode.
2.Turn main dial to select the desired channel address to store.
3.Press
key, and then hold
for 2 seconds, after two "beep" sounds, this channel has been stored.
Delete Channel
1.In Standby state, after pressing
key, the top left corner of LCD displays " " , then press
the channel number twinkling means getting into store/ delete channel mode.
2.Turn selector knob to select the channel which you want to delete.
key, and hold
key for 2 seconds, the frequency disappear with in two "beep"
3.Press
sounds, the channel has been deleted.
FM Radio Receiver
1. Under standby state, press
key, top left corner of LCD displays " " icon,then
press
key again, LCD displays "FM" icon and "FM ON" , FM radio function
is on.
2. While "FM ON" is indicated on the display, press
key to turn on/off FM
radio function, FM radio is on when LCD displays "FM ON", FM radio is off
when LCD displays "FM OFF".
18 Professional
FM Transceiver
,
ADVANSED OPERATIONS
key firstly, then press
key to search broadcasting stations, the
3. When FM radio is on, press
searched stations will be saved into FM radio channels automatically.
4. When FM radio is on, press
key firstly, then press
key to scan broadcasting stations, when
meeting stations, scan will stay 5 seconds then resume.
5. Press
key to exit FM radio mode.
Note: When RADIO function is set as OFF in programming software, this function is invalid.
Add or Cancel DTMF, 2TONE, 5TONE,FSK Signaling
DTMF, 2TONE,5TONE,FSK signaling are similar to CTCSS / DCS, while DTMF and 5TONE have other
special functions, including ANI, PTTID, call all, group call, single call, alarm, remotely Kill, remotely
Stun,Revive, and tail-eliminating. For more information and setup, please refer to the help option in the
programming software.
Main channel in frequency mode / frequency +channel mode/channel name mode, after pressing
key, the top left corner of LCD displays" " , then press
key. Repeat the operation above, 4
statuses available.
1. When the first digit displays "D", it has DTMF signaling squelch when
receive. Hold [PTT] key then press [PF2] key to transmit the prestored and
selected DTMF signaling.
2. When the first digit displays "T", it has 2TONE signaling squelch when receive. Hold [PTT] key then
press [PF2] key to transmit the prestored and selected 2TONE signaling.
3 When the first digit displays "F", it has 5TONE signaling squelch when receive. Hold [PTT] key then
press [PF2] key to transmit the prestored and selected 5TONE signaling.
Professional
FM Transceiver
19
ADVANSED OPERATIONS
4. When the first digit displays "M", it has FSK signaling squelch when receive.
Hold [PTT] key then press [PF2] key to transmit the prestored and selected
FSK signaling.
5.When displays none of alphabetical character, DTMF, 2TONE, 5TONE, FSK
signaling are cancelled. Even in the channel mode, above change may be
applied temporary.
Note: Details will be explained later in the Channel operation chapter.
CTCSS / DCS Scan
key, the top left corner of LCD displays " ", then press
to enter CTCSS / DCS
After pressing
scan. When signaling scanned matches the setting of the transceiver, stop for 15 seconds then scan
to exit scanning.
again. Press any keys except
Note: This function is invalid when the main channel is in channel
display mode or current mode without signaling setup.
Scan CTCSS when the current channel is set to CTCSS, scan DCS when
the channel is set to DCS.
Turn main dial to change the CTCSS / DCS scan direction.
20 Professional
FM Transceiver
ADVANSED OPERATIONS
Add or cancel CTCSS/DCS
Under standby state, press
key, the top left corner of LCD displays " "
key to choose CTCSS/DCS signaling.
icon, then press
1. LCD displays "CT" icon, means current channel add CTCSS encode and
decode.
2. LCD displays "DCS" icon, means current channel add DCS encode and
decode.
3. None of icons is displayed on the LCD means CTCSS/DCS signaling is not
available.
Frequency Scan, Channel Scan or FM Search
key, while
icon is displayed on the top left corner, press
key
While receiving, after pressing
to begin frequency scan or channel scan. Scan-resume condition can be set in the set mode that will be
explained later. Default is timed and resumes scanning after 15 seconds regardless of receiving state.
1.Frequency Scan
In VFO mode, it scans in accordance with the channel step. Press any key except
keys to stop scanning.
,
or
Note: An advanced PA/PB frequency scans may be available after dealer-programming.
Professional
FM Transceiver
21
ADVANSED OPERATIONS
2.Channel Scan
In channel mode, it scans in accordance with preprogrammed channels. Press any key except
or
keys to stop scanning.
,
3.FM Search
In FM broadcast receiver mode, it scans in accordance with 100KHz step. Press any key except
or
keys to stop scanning.
,
Note:
Turn the main dial clockwise or counter-clockwise to change scan direction.
Channels selected as "skip channels" won't be scanned during the channel scanning.
Scan Channel Skip
In Channel mode or Memory mode, after pressing
key, press
key to
set the current channel to be skipped while channel-scanning, and ‘S’ icon
appears to indicate the channel is set as the skip. Repeat the operations to
cancel channel scan skip setting. The S icon will dessapear.
Note: This feature is available only in the Channel modes.
22 Professional
FM Transceiver
ADVANSED OPERATIONS
Priority Monitor
key, while
icon is displayed on the top
In VFO mode, after pressing
left corner, press
key to activate the priority monitor. PRI icon appears
and monitors preprogrammed priority channel once every 5 seconds. When
the priority channel receives a matching signal, it will stay tuned to the priority
channel until current signal disappears. Press any keys other than D key to exit.
Note: To activate this feature, it is required to set and select the priority channel in advance.
TX Power Selection
After pressing
key, while
icon is displayed on the top left corner, press
key to set the output
power. When the bottom left corner of screen displays 'H' the power is 5W/high power.‘L’ for 0.5W.
When nothing is displayed, the output power is middle/2W.
Professional
FM Transceiver
23
ADVANSED OPERATIONS
FSK Message Single Transmitting
1. In standby state, press
key, the top left corner of LCD displays " " icon.
key, LCD displays '_MSG_'.
2. Press
3. Turn main dial to select the desired character.
4. Press [PF1] key to confirm the current character and enter next character .
5. Press [PF2] key to return previous character. Total 18 characters can be
entered.
key, LCD displays "CALL ID".
6. Press
7. Enter the desired calling ID.
8. Press [PTT] key to transmit FSK message.
FSK Message Group Transmitting
key, the top left corner of LCD displays " " icon.
1. In standby state, press
key, LCD displays '_MSG_'.
2. Press
3. Turn main dial to select the desired character.
4. Press PF1 key to confirm the current character and enter next character.
5. Press PF2 key to return previous character. Total 18 characters can be entered.
key, LCD displays "CALL ID",then press
key/
key to
6. Press
select "CAL GR".
7. Enter the desired calling Group ID.
24 Professional
FM Transceiver
ADVANSED OPERATIONS
8. Press [PTT] key to transmit FSK message.
FSK Message All Transmitting
1. In standby state, press
key, the top left corner of LCD displays " " icon.
key, LCD displays '_MSG_'.
2. Press
3. Turn main dial to select the desired character.
4. Press [PF1] key to confirm the current character and enter next character.
5. Press [PF2] key to return previous character. Total 18 characters can be
entered.
key, LCD displays "CALL ID". Press
or
key to select
6. Press
"CAL AL".
7. Press PTT key to transmit FSK message.
Note: Pressing PTT after having edited the message will send the message to all
users.
FSK message checking
Press and hold
Press
or
key for 1 second to check the receiving short message.
key to read more messages. Press
key to exit.
Note: When no message is being received, a beep sounds and the
message won't be displayed.
Professional
FM Transceiver
25
ADVANSED OPERATIONS
DTMF Code Searching And Setup
After pressing
key, the top left corner of LCD displays" " then press 0
key, it displays the current DTMF group. (16 groups in total)
1.Turn main dial to select the desired group and DTMF data, and press PTT
to transmit the desired DTMF data. It displays EMPTY when DTMF data is
not programmed yet.
key, the top left corner of LCD displays " ", press and hold 0
2.Press
key for 2 seconds to enter DTMF editing menu. Use numerical keys to enter
DTMF characters. Press [PF2] key to transmit the tones, save the data and exit.
Manually Transmitting DTMF Signaling
Method 1: hold [PTT] key and enter the number you need in keyboard.
Method 2: hold [PTT] key and enter the first number, release [PTT] key, the transceiver will stay in
transmitting situation in 2 seconds and you can keep on entering the numbers you need in
keyboard. You do not need to keep holding [PTT] key to enter. When transmitting DTMF
frequency, you can monitor the frequency by the sounds making by the loudspeaker.
Remotely Kill/Revive
By transmitting preprogrammed KILL code, the radios that received the code
will become temporary out-of-service. When KILL code is received, KILL is
displayed and all keys and functions will be suspended for use.
26 Professional
FM Transceiver
ADVANSED OPERATIONS
To wake up (revive) the radios again, send the KILL code with # at the end.
Example: If 1234 is the KILL code, send 1234# to revive. It displays "WAKEN"
when revive code is received. Turn off and turn on to operate.
Remotely Stun /Waken
By transmitting preprogrammed STUN code, the radios that received the code
will become temporary out-of-service except for receiving. When STUN code is
received, STUN is displayed and all keys and functions will be suspended for
use.
To wake up (revive) the radios again, send the STUN code with # at the
end. Example: If 5678 is the STUN code, send 5678# to revive. It displays
"WAKEN" when revive code is received. Turn off and turn on to operate.
RF Attenuator (ATT)
In case receiving signal is excessively strong that bothers hearing, ATT may
become useful.
" icon.
1. Press A key, the top left corner displays "
key, ATT icon appears on the left bottom and ATT is on.
2. Press
3. Repeat above to exit and ATT icon disappears.
Professional
FM Transceiver
27
CHANNEL OPERATIONS
For VFO or Memory channel mode users, temporary changes in preset channel parameter may be
available. Such temporary changes won't be held in the memory and will be deleted when a channel is
changed or turn off the radio.
This feature is not available to dealer-programmed Channel mode users.
Please ask your dealer for details of programming.
key, the top left corner of LCD displays" " then press
key to enter function
1.After pressing
menu.
2.Press
/
key to select the menus to be set.
3.Turn main dial to choose the parameter.
4.Press
key or
key to confirm and exit the setup.
CTCSS / DCS Encode Setup
" then press
1.After pressing A key, the top left corner of LCD displays "
key.
2.Press
/
key to choose menu 01. LCD will display " T-CDC "
3.Press 1 key to choose CTCSS, DSC or OFF. When DCS is selected, press
key to choose positive or inverse code.
4.Turn main dial to choose the desired CTCSS / DCS encodeing tone. See
appendix for details of available tones.
5.Press
key or
key to confirm and exit.
28 Professional
FM Transceiver
CHANNEL OPERATIONS
CTCSS/DCS Decode
By using this function with CTCSS/DCS encode feature, you hear only signals
that are sent with matching tones. (Such operations are often reffered to as
Tone-Squelch or DCS squelch)
1.After pressing
key, the top left corner of LCD displays"
" then press
key.
2.Press
/
key to choose menu 02. LCD will display " R-CDC "
3.Press
key to choose CTCSS, DSC or OFF. When DCS is selected,
press
key to choose positive or inverse code.
4.Turn main dial to choose the desired CTCSS / DCS decodeing tone. See
appendix for details of available tones.
5.Press
key or
key to confirm and exit.
Note: You may set the encoding and decoding tones separately.
Choose To Transmit 2TONE
By preprogramming the 2-Tone setting in advance, you may select the tone and transmit it.
key, the top left corner of LCD displays"
" then press
1.After pressing
key.
2.Press
/
key to choose menu 03. LCD will display " 2TONE "
3.Turn main dial to choose the desired 2-Tone signal. Press PTT to transmit
the tone. Up to 32 tones are programmable.
5.Press
key or
key to confirm and exit.
Professional
FM Transceiver
29
CHANNEL OPERATIONS
Choose To Transmit 5TONE
By preprogramming the 2-Tone setting in advance, you may select the tone
and transmit it.
1.After pressing
key, the top left corner of LCD displays"
" then press
key.
2.Press
/
key to choose menu 04. LCD will display " 5TONE "
3.Turn main dial to choose the desired 5-Tone signal. Press PTT to transmit the tone. Up to 100 tones
are programmable.
5.Press
key or
key to confirm and exit.
Choose To Transmit FSK
By preprogramming the FSK setting in advance, you may select the tone and transmit it.
1.After pressing
key, the top left corner of LCD displays"
" then press
key.
2.Press
/
key to choose menu 05. LCD will display "FSK ENC"
3.Turn main dial to choose the desired FSK Encoding signal. Press PTT to
transmit the tone. Up to 100 tones are programmable.
4.Press
key or
key to confirm and exit.
30 Professional
FM Transceiver
CHANNEL OPERATIONS
Signaling Combination
You may combine the signaling functions of different system.
1.After pressing
key.
key, the top left corner of LCD displays"
" then press
/
key to choose menu 06. LCD will display " SIGNAL"
2.Press
3.Turn main dial to choose the desired signaling combinations mentioned
below.
- SQ: Hear all communications regardless of the signaling tones.
- CT/DCS: Hear only the signals with matching CTCSS or DCS tones.
- Tone: Hear only the signals with matching DTMF, 2-Tone or 5-Tone tones.
- CT&TO: Hear only the signals with matching CTCSS, DCS, DTMF,2-Tone
or 5-Tone tones.
- CT/TO: Hear only the signals with matching any one of CTCSS, DCS,
DTMF, 2-Tone or 5-Tone tones.
4.Press
key or
key to confirm and exit.
Professional
FM Transceiver
31
CHANNEL OPERATIONS
Frequency Step
1.After pressing
key, the top left corner of LCD displays"
" then press
/
key to choose menu 07. LCD will display "STEP".
2.Press
3.Turn main dial to choose the desired step mentioned below.
4. Press
key or
key to confirm end exit.
Available steps are 5,6.25,8.33,10,12.5,20,25,30 and 50KHz.
This parameter is not available when the radio is in the Channel mode.
Offset Direction
1.After pressing
key, the top left corner of LCD displays"
" then
key.
press
2.Press
/
key to choose menu 08. LCD will display "SHIFT".
3.Turn main dial to choose the desired Offset direction.
SBC -: Negative offset, TX frequency is lower than RX frequency.
ADD+: Positive offset, TX frequency is higher than RX frequency.
Select OFF for simplex operation.
key or
key to confirm end exit.
4. Press
32 Professional
FM Transceiver
key.
CHANNEL OPERATIONS
Offset Frequency
1.After pressing
key, the top left corner of LCD displays"
" then press
key.
/
key to choose menu 09. LCD will display "OFF SET".
2.Press
3.Turn main dial to choose the desired Offset frequnecy.
Available parameters are 0.00 to 69.995MHz in step size selected in menu 07.
key or
key to confirm end exit.
4.Press
Wide/ Narrow FM Mode
1.After pressing
key, the top left corner of LCD displays"
" then
key.
press
2.Press
/
key to choose menu 11. LCD will display " W/N".
3.Turn main dial to choose the desired bandwidth frequnecy.
Available parameters are 12.5(narrow),20(middle) and 25KHz(wide).
key or
key to confirm end exit.
4.Press
Note: Be sure to use correct bandwidth assigned to your radio service otherwiseyour signal
may cause interferences to your adjacent frequnecy users.
Professional
FM Transceiver
33
CHANNEL OPERATIONS
Frequency Reverse
This function temporary reverses the transmitting and receiving frequencies and signaling tone settings.
1.After pressing
key, the top left corner of LCD displays"
" then press
key.
/
key to choose menu 12. LCD will display "REV".
2.Press
3.Turn main dial to choose the desired parameter.
ON: enable frequency reverse.
OFF: disable frequency reverse.
key or
key to confirm end exit.
4.Press
This function is not available when Talk Around function is activated.
Talk Around
1.After pressing
key, the top left corner of LCD displays"
" then press
key.
2.Press
/
key to choose menu 13. LCD will display "TAL KAR".
3.Turn main dial to choose the desired parameter.
TX=RX: talk around enables / OFF: talk around disables
key or
key to confirm end exit.
4: Press
34 Professional
FM Transceiver
CHANNEL OPERATIONS
Busy Channel Lockout
This function prohibits the transmitting when the channel is busy.
key, the top left corner of LCD displays"
" then press
1.After pressing
key.
2.Press
/
key to choose menu 14. LCD will display "LOCK".
3.Turn main dial to choose the desired parameter.
-REPEAT: Signaling busy lock. It suspends transmitting when receives a
matching carrier but incorrectsignaling tones.
-BUSY: Carrier busy lock. It suspends transmitting when receives any carrier
signal.
- OFF: PTT operation is always possible without busy channel lockout.
4.Press
key or
key to confirm end exit.
Prohibits transmitting
1.After pressing
key, the top left corner of LCD displays"
" then press
key.
2.Press
/
key to choose menu 15. LCD will display "TX".
3.Turn main dial to choose the desired parameter.
ON:Transmitting is allowed / OFF:Transmitting disabled
key or
key to confirm end exit.
4.Press
Professional
FM Transceiver
35
CHANNEL OPERATIONS
Sub Channel Display Setup
1.After pressing
key, the top left corner of LCD displays"
" then press
key.
2.Press
/
key to choose menu 16. LCD will display "DSP SEL".
3.Turn main dial to choose the desired parameter.
NAME: Display current channel name
VOLT: Display current battery voltage
CTDC: Display current CTCSS/DCS signaling
TONE: Display current optional signaling (DTMF, 5TONE,2TONE or FSK)
key or
key to confirm end exit.
4.Press
Compander
Compander reduces carrier noises and enhances the audio clarity.
1.After pressing
key, the top left corner of LCD displays"
" then press
key.
2.Press
/
key to choose menu 17. LCD will display "COMP".
3.Turn main dial to choose the desired parameter.
ON: Enable compander / OFF: Disable compander
key or
key to confirm end exit.
4: Press
Note: Activate the compander only when all users are using the compander-compatible radios.
36 Professional
FM Transceiver
CHANNEL OPERATIONS
Scrambler Setup (Encryption)
1.After pressing
key, the top left corner of LCD displays"
" then press
key.
2.Press
/
key to choose menu 18. LCD will display "SCR".
3.Turn main dial to choose the desired parameter.
-1-10: Select one of 10 preset scrambling parameters for easier operation.
-USER: Preprogrammed user-customized sclambring parameter
-OFF: Disable scrambler
key or
key to confirm end exit.
4.Press
Professional
FM Transceiver
37
SET MODE OPERATIONS
You may customize the features and functions of the radio to better suit your operation comfort.
Customization may not be available to preprogrammed radios. Please consult your dealer for setting
details.
To operate Set mode:
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to select desired function to customize.
2.Press
3.Turn the main dial to select the desired parameter.
4.Press
key or
key to confirm and exit.
Beep and Voice assist sounds
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 01. LCD will display "VOICE".
2.Press
3.Turn the main dial to select the desired parameter.
ENG: English voice / BEEP: Beep sounds / OFF: Turn off both
key or
key to confirm and exit.
4.Press
Time-Out Timer
The purpose of the Time-out Timer is to prevent any caller from using a channel for an extended period
of time. If you continuously transmit to exceed the limit, it stops transmitting and alert with a beep tone (if
tone is activated in menu 01).
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
38 Professional
FM Transceiver
SET MODE OPERATIONS
2.Press
/
key to choose menu 02. LCD will display "TOT".
3.Turn the main dial to select the desired parameter.
1-30MIN: Up to 30 minute timer out time selectable by 1 minute step.
OFF: Disable TOT
key or
key to confirm and exit.
4.Press
Voice Operated Transmission (VOX)
VOX operation allows you to transmit hands-free. You don't need to press [PTT]
key to transmit only through voice. This function is available only when the
supported earphone microphone (EME-56A) is used.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 03. LCD will display "VOX".
2.Press
3.Turn the main dial to select the desired parameter.
-1-10: The microphone sensitivity level to start transmitting. Higher the number,
louder you speak to activate the VOX.
- OFF: VOX disable
key or
key to confirm and exit.
4.Press
Professional
FM Transceiver
39
SET MODE OPERATIONS
Voice Operated Transmission (VOX) Delay Time
This parameter determines the delay time from stop speaking to return to
receiving in VOX operation.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 04. LCD will display "VOX DL".
2.Press
3.Turn the main dial to select the desired parameter.
- 0.3 to 3 in seconds: 28 parameters in 0.1 seconds step.
key or
key to confirm and exit.
4.Press
Auto Power-Off
This parameter determines the Auto Power Off time setting.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 05. LCD will display "POWER".
2.Press
3.Turn the main dial to select the desired parameter.
- 30MIN: Automatic Power-Off after 30 minutes
-1HOUR: Automatic Power-Off after one hour
- 2HOUR: Automatic Power-Off after two hours
key or
key to confirm and exit.
4.Press
40 Professional
FM Transceiver
SET MODE OPERATIONS
DTMF Burst and Pause timing
This parameter determines the DTMF burst and pause timing setting.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 05. LCD will display "DTMF".
2.Press
3.Turn the main dial to select the desired parameter.
30MS: DTMF bursts 30 miliseconds and pauses 30 miliseconds
50MS: Same as above for 50miliseconds
100MS: Same as above for 100miliseconds
200MS: Same as above for 200miliseconds
300MS: Same as above for 300miliseconds
500MS: Same as above for 400miliseconds
key or
key to confirm and exit.
4.Press
Squelch Level
This parameter determines the squelch level. This is the same operation as
PF2 key and main dial. Setting the level too low will hear the noise often, but
too high may risk not receiving weaker signals.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 07. LCD will display "SQL".
2.Press
3.Turn the main dial to select the desired squelch level from 00 to 11.
4.Press
key or
key to confirm and exit.
Professional
FM Transceiver
41
SET MODE OPERATIONS
Scan Resume Conditions
This parameter determines the resume conditions of scanning.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 08. LCD will display "SCAN".
2.Press
3.Turn the main dial to select the desired parameter.
-5ST: Resumes scanning after 5 seconds regardless of receiving state
-10ST: Resumes scanning after 10 seconds regardless of receiving state
-15ST: Resumes scanning after 10 seconds regardless of receiving state
-2SP (Busy scan): Resumes scanning after 2 seconds from the receiving signal is gone
key or
key to confirm and exit.
4.Press
42 Professional
FM Transceiver
SET MODE OPERATIONS
Function Key Setting time
This parameter determines the resume conditions of scanning.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 08. LCD will display "FTIME".
2.Press
3.Turn the main dial to select the desired parameter.
icon disappears and exits
- FUNCT: When function key operating finishes,
from Function operations.
- 1SEC/2SEC/3SEC: When function key operating finishes, F icon disappears
and exits from Function operations after 1/2/3 seconds is elapsed respectively.
ALWAYS: Function operation is always active until A key is pressed.
key or
key to confirm and exit.
4.Press
Backlight On/Off Mode
This parameter determines the LCD/Keypad illumination timing.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
2.Press
/
key to choose menu 10. LCD will display "LIGHT".
3.Turn the main dial to select the desired parameter.
OFF: Illumination deactivated. The battery consumption is minimum.
ON: Illumination remain turned on always. Never select this while operating
with the battery.
AUTO: Illumination turns on for 2 seconds after any key operation then turns
off automatically. This is usually recommended.
key or
key to confirm and exit.
4.Press
Professional
FM Transceiver
43
SET MODE OPERATIONS
Backlight Color Setup
This parameter determines the LCD/Keypad illumination timing.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 11. LCD will display "COLOR".
2.Press
3.Turn the main dial to select the desired parameter.
- BLUE: RX/Blue TX/Purple
- ORG: RX/Orange TX/Blue
- PUR: RX/ Purple TX/Orange
key or
key to confirm and exit.
4.Press
44 Professional
FM Transceiver
SET MODE OPERATIONS
Display Mode
This parameter determines the LCD display mode. This parameter may not be
available for dealer-programmed radios.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 12. LCD will display "DSP".
2.Press
3.Turn the main dial to select the desired parameter.
-FREQ: channel frequency + channel number display
-CH: channel number display.
-NAME: Channel name+ Channel number display
key or
key to confirm and exit.
4.Press
DTMF Self ID display
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
2.Press
/
key to choose menu 13. LCD will display "DT-ID".
3. LCD displays DTMF self ID number.
4.Press
key or
key to confirm and exit.
Professional
FM Transceiver
45
SET MODE OPERATIONS
5TONE Self ID Inquiry
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
2.Press
/
key to choose menu 14. LCD will display "5T-ID".
3. LCD displays DTMF self ID number.
4.Press
key or
key to confirm and exit.
Tone-burst tone setting
Select the Tone-burst tone frequency. 4 tones are available. To transmit the tone-burst, press PF1 key
while transmitting.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 15. LCD will display "5T-ID".
2.Press
3.Turn the main dial to select the desired parameter. Available tones are
1000/1450/1750/2100Hz
key or
key to confirm and exit.
4.Press
46 Professional
FM Transceiver
SET MODE OPERATIONS
Battery Save Ratio
Select the battery save time-ratio. Longer the sleep time, lower the battery
consumption but you may risk missing an initial part of calling signal.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 16. LCD will display "SAVE".
2.Press
3.Turn the main dial to select the desired parameter.
OFF: Battery save function OFF. Not recommended for battery operation
1:2: operative/sleep ratio is 1:2.
1:3: BS ratio 1:3.
1:5: BS ratio 1:5.
1:8: BS ratio 1:8
AUTO: Automatically adjust the ratio and most recommended.
key or
key to confirm and exit.
4.Press
Professional
FM Transceiver
47
SET MODE OPERATIONS
FM Radio
1.Pressing and holding [PF2] key to turn on the radio to enter the Set
mode.
2.Press
/
key to choose menu 17. LCD will display "RADIO".
3.Turn the main dial to select the desired parameter.
-ON: FM radio receive is allowed.
-OFF: FM radio is prohibited.
key or
key to confirm and exit.
4.Press
Password
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
2.Press
/
key to choose menu 18. LCD will display "CODE".
3.Turn the main dial to select the desired parameter.
-ON: Password function is on, correct password must be input when power on
the radio.
-OFF: Password function is off.
key or
key to confirm and exit.
4.Press
48 Professional
FM Transceiver
SET MODE OPERATIONS
RESET
In case the radio is malfunctioning or you may resume the default conditions of the radio, please
perform this factory reset.
1.Pressing and holding [PF2] key to turn on the radio to enter the Set mode.
/
key to choose menu 19. LCD will display "RESTOR".
2.Press
3.Turn the main dial to select the desired parameter.
FACT?: Restore factory default
SETUP?: Restore custom parameters only to default leaving the memory
OFF: Do not perform reset
key to perform the reset.
4.Press
* Reset is not available to dealer-programmed or Channel mode radios.
Professional
FM Transceiver
49
Default settings
VFO Frequency
Memory Channel
155.000MHz
Keylock
CH0:155.000MHz
CTCSS/DCS Decode/Encode
CH1-CH199:Blank
Offset Frequency
Off
None
600KHz
PF1 long press key
Channel Spacing
PF1 short press key
Scramble
None
Voice Compander
OFF
Busy Channel Lockout
OFF
Optional Signaling
OFF
Voice Prompting
Beep
Time-Out Timer
3 Minutes
Vox Setup
Off
VOX Delay
0.3SEC
Frequency Step
12.5K
Squelch Level
4
Battery Save
1:2
LCD Backlight
LCD Backlight Color
Display Mode
Auto
Orange
1Frequency
DTMF Transmitting Time
50ms
Priority Channel
CH0
FM Radio
OFF
Offset Frequency Setup
OFF
Channel Scan Skip
NO
TX Power Selection
High
DTMF Code
None
50 Professional
FM Transceiver
25K
Squelch Mode
SQ
PTT ID
OFF
TX Function
ON
OPTIONAL ACCESSORIES
EA-211
VHF & FM radio Antenna
EBC-34
Belt Clip
EBP-87
Li-ion Battery Pack (DC 7.4V 1500mAh)
EBP-88
Li-ion Battery Pack (DC 7.4V 1700mAh)
EDC-189
Li-ion Battery Charger
EDC-190E
AC Adaptor (220V Linear type)
EDC-191E
AC Adaptor (220V)
EDC-191T
AC Adaptor (120V)
EME-56A
Earphone Microphone
Professional
FM Transceiver
51
Recommended installation of earphone microphone
Earphone
Use a clip to fix with collar.
Clip the PTT unit closer to your mouth.
Carry the radio on the side or the back of your body,
and the cable should go around the back as shown.
Clamp the excessive length of cable at your waist
52 Professional
FM Transceiver
AUXILIARY FUNCTIONS
For dealers only. Please contact the authorized importer of your area for more details.
Cable Cloning
With this function, you can copy the programming data of the transceiver to another one; it can copy
parameters and memory programming data to another transceiver.
Connection: use wire cloning cable (optional accessory) to connect main transceiver with subtransceiver through reading/ writing programmable interface.
Setup: main transceiver party
1.Hold [PF1] side key to power on, LCD displays "CLONE", main transceiver enters into copy mode.
2.Press [PTT] key , LCD displays "CLONE XX", XX means the transmitted data quantity.
3.After data copies completely, LCD displays "CLONE OK".
4.Main transceiver stays in this mode preparing to next copy, restart main transceiver to exit copy mode.
Setup: sub-transceiver party.
1.When receiving data, LCD displays "CLONE XX ", XX means the received data quantity.
2.After data received sub-transceiver returns to normal mode.
3.Power off, take over cable line and link to another sub-transceiver which you want to copy.
If data can not transfer successfully, power off main transceiver and sub-transceiver, check the cable
line and repeat the process.
Communication Note
This function is used to receive ANI call matching the communication note, and displays the corresponding name of the code in LCD. It is similar to mobile phone communication note. You can set 15 groups
of 5TONE note and DTMF note each. You only need to set the opposing party ID with the corresponding
name. For more information, please refer to the communication note option in software.
Professional
FM Transceiver
53
TECHNICAL SPECIFICATIONS
Technical Specifications
General
Frequency range
TX/RX
136.000-173.995MHz
FM radio
76-108MHz (RX only)
Modulation
F3E(16K0F3E/11K0F3E / RX only WFM)
Programmable channels
200 channels
Frequency stability
±2.5ppm
Power supply
DC7.4V (Battery only)
Current drain
TX(5W)
≤1.4A
RX
≤300mA
Stand-by
≤70mA
Battery save on
≤30mA
Temperature range
Operating:-20~+55℃(-4~131°F) / Charging:+5~+40℃(+41~104°F)
Dimensions
(Projections not included/approx.)
59(W) x 98(H) x 35(D) mm
2.32"(W) x 3.86"(H) x 1.38"(D)
Weight *approx
227g or 8.01oz (with battery pack and antenna)
54 Professional
FM Transceiver
TECHNICAL SPECIFICATIONS
Transmitter
Output power (Approx.)
high
5W
middle
2W
low
0.5W
Modulation
Variable reactance FM
Spurious emissions
-60dB or less
Max.deviation(Wide/Narrow)
±5kHz / ±2.5kHz
Receiver
Receive system
Double coversation superheterodyne
Intermediate frequencies
38.85MHz (1st) / 450kHz (2nd)
Sensitivity(12dB SINAD)
wide -12dBu, Narrwo -9dBu
Selectivity
-6dB : 12kHz or more /-60dB : 30kHz or less
Audio output power
1W (10% distortion)
* All specifications are subject to change without notice or obligation.
* ALINCO and Alinco logo are registered trademarks of Alinco,Inc in many countries including USA, Russia, EU states
and China.
Professional
FM Transceiver
55
TROUBLE SHOOTING GUIDE
Problem
Corrective Action
No power
A.The battery may be exhausting. Recharge or replace the battery.
B.The battery may not be installed correctly. Remove the battery
and install it again.
C.The power switch is broken; send it to local dealers to repair.
D.Battery life is end; contact to local dealers to replace.
Battery power dies shortly after
charging.
The battery is exhausted. Replace the battery pack with a new one.
Transceiver cannot scan
The channels are not programmed.
All band noisy after programmed
Adjust squelch level.
No sound when using earphone.
Earphone or the jack is broken. Please contact with local dealers for
inspection.
Communication distance
becomes short, and Low
sensitivity
A.Check whether the antenna is in good conduction and the antenna
base do not come adrift.
B.Antenna may be broken. Consult your local dealer for services.
Cannot talk or hear other
members in your group
A.Different frequency or channel, please change it.
B.Different CTCSS / DCS /DTMF, please reset it.
C.Out of communication range.
Can not power on or frequent
power off
Check if the battery pack is securely attached.
56 Professional
FM Transceiver
TROUBLE SHOOTING GUIDE
The receiving sound level is low
or intermittent
Consult with local dealers for inspection.
Receiving signal is intermittent.
A.Out of communication range or obstruct by walls, buildings etc.
Change position to transmit.
B.4Internal components may be in trouble, please contact with local
dealers to repair.
Loudspeaker sounds lower or
with dry noise after certain time of
usage.(Speaker magnet attracts
iron powders)
Receive voice from the other
parties and can not transmit
Receiving indicator with green
light but no sound
Check whether the loudspeaker is broken, Iron powder or dusts is in
the loudspeaker. Please contact with local dealers to repair.
Interference is being received. BCLO activated.
A.Low volume, increase the audio level.
B.Volume switch or loudspeaker is broken, please contact with local
dealers to repair.
C.Earphone jack is broken, please contact with local dealers to
repair.
Professional
FM Transceiver
57
APPENDIX
CTCSS Frequency Chart
1
62.5
12
94.8
23
136.5
34
177.3
45
218.1
2
67.0
13
97.4
24
141.3
35
179.9
46
225.7
3
69.3
14
100.0
25
146.2
36
183.5
47
229.1
4
71.9
15
103.5
26
151.4
37
186.2
48
233.6
5
74.4
16
107.2
27
156.7
38
189.9
49
241.8
6
77.0
17
110.9
28
159.8
39
192.8
50
250.3
51
254.1
7
79.7
18
114.8
29
162.2
40
196.6
8
82.5
19
118.8
30
165.5
41
199.5
9
85.4
20
123.0
31
167.9
42
203.5
10
88.5
21
127.3
32
171.3
43
206.5
11
91.5
22
131.8
33
173.8
44
210.7
58 Professional
FM Transceiver
APPENDIX
1024 Groups DCS Chart
000
010
020
030
040
050
060
070
100
110
120
130
140
150
160
170
200
210
220
230
240
250
001
011
021
031
041
051
061
071
101
111
121
131
141
151
161
171
201
211
221
231
241
251
002
012
022
032
042
052
062
072
102
112
122
132
142
152
162
172
202
212
222
232
242
252
003
013
023
033
043
053
063
073
103
113
123
133
143
153
163
173
203
213
223
233
243
253
004
014
024
034
044
054
064
074
104
114
124
134
144
154
164
174
204
214
224
234
244
254
005
015
025
035
045
055
065
075
105
115
125
135
145
155
165
175
205
215
225
235
245
255
006
016
026
036
046
056
066
076
106
116
126
136
146
156
166
176
206
216
226
236
246
256
007
017
027
037
047
057
067
077
107
117
127
137
147
157
167
177
207
217
227
237
247
257
Professional
FM Transceiver
59
APPENDIX
260
270
300
310
320
330
340
350
360
370
400
410
420
430
440
450
460
470
500
510
520
530
60 Professional
FM Transceiver
261
271
301
311
321
331
341
351
361
371
401
411
421
431
441
451
461
471
501
511
521
531
262
272
302
312
322
332
342
352
362
372
402
412
422
432
442
452
462
472
502
512
522
532
263
273
303
313
323
333
343
353
363
373
403
413
423
433
443
453
463
473
503
513
523
533
264
274
304
314
324
334
344
354
364
374
404
414
424
434
444
454
464
474
504
514
524
534
265
275
305
315
325
335
345
355
365
375
405
415
425
435
445
455
465
475
505
515
525
535
266
276
306
316
326
336
346
356
366
376
406
416
426
436
446
456
466
476
506
516
526
536
267
277
307
317
327
337
347
357
367
377
407
417
427
437
447
457
467
477
507
517
527
537
APPENDIX
540
550
560
570
600
610
620
630
640
650
660
670
700
710
720
730
740
750
760
770
541
551
561
571
601
611
621
631
641
651
661
671
701
711
721
731
741
751
761
771
542
552
562
572
602
612
622
632
642
652
662
672
702
712
722
732
742
752
762
772
543
553
563
573
603
613
623
633
643
653
663
673
703
713
723
733
743
753
763
773
544
554
564
574
604
614
624
634
644
654
664
674
704
714
724
734
744
754
764
774
545
555
565
575
605
615
625
635
645
655
665
675
705
715
725
735
745
755
765
775
546
556
566
576
606
616
626
636
646
656
666
676
706
716
726
736
746
756
766
776
547
557
567
577
607
617
627
637
347
657
667
677
707
717
727
737
747
757
767
777
Professional
FM Transceiver
61
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement