F220‑B6RS 24 VDC Four‑wire Detector Base with Sounder

F220‑B6RS 24 VDC Four‑wire Detector Base with Sounder
Fire Alarm Systems | F220‑B6RS 24 VDC Four‑wire Detector Base with Sounder
F220‑B6RS 24 VDC Four‑wire Detector
Base with Sounder
www.boschsecurity.com
The F220‑B6RS 24 VDC Four-wire Detector Base with
Sounder meets the requirements of UL464 for a
notification device and works with the F220
Photoelectric Smoke and Heat Detectors. Power the
sounder from the control panel's NAC circuit or from
auxiliary power.
Functions
Sounder Configuration
The output (sound pattern and synchronization) of the
sounders on a detection loop can be configured in four
different ways. Refer to the F220 Series Detectors
Installation Instructions (P/N: 4998138694) for
instructions on wiring and setting the F220‑B6RS
detector base for these configurations:
1.
NAC Follower (Direct Wire) Configuration: In this
configuration, the sounders on the loop follow the
signal on the NAC terminals as programmed at the
control panel. Refer to the control panel's installation
manual for NAC configuration instructions. This
configuration requires an extra pair of supervised
wires for the sounder circuit.
u
Easy installation
u
Interchangeable detector heads
u
UL listed when used with a detector from the F220
family
u
UL464 approved sounder driven by the detector
head or the NAC circuit
2.
3.
4.
Reverse Polarity Configuration: In this configuration
(not suitable for synchronized protocols; such as,
Cooper Wheelock, Gentex, or System Sensor), the
sounders in a loop activate due to reversed polarity
on the power line. The output pattern is not
controlled by the base in this operating mode; it
follows the reversing power signal on the detector
head's terminals as programmed at the control panel.
Local Annunciation Configuration: In this
configuration, each sounder is individually set for one
of the following patterns: Temporal (Code 3), March
Time, or Continuous Tone. Use a D275 Power
Supervision Module in this configuration to supervise
the detector loop.
Interconnection Configuration: In this configuration,
up to five detectors supervise the end of the detector
loop when interconnected by a common wire. All
sounders within the group activate together. Set all
units for the same output pattern (Temporal [Code
3], March Time, or Continuous Tone). All
interconnected detectors are synchronized with and
sound the pattern of the originating detector.
The maximum wire length for connecting up to five
units is:
2 | F220‑B6RS 24 VDC Four‑wire Detector Base with Sounder
Wire Size
Wire Length
18 AWG (ISO 0.75 mm2)
300 ft (91 m)
16 AWG (ISO 1.5 mm )
450 ft (137 m)
14 AWG (ISO 2.5 mm )
750 ft (229 m)
2
2
Notice
To ensure interconnected units can signal an
alarm, the line load after the last detector on the
interconnected detector loop must not exceed
10 mA.
Certifications and approvals
Notice
The electrical box must be large enough to
accommodate the number and size of conductors
specified by the National Electrical Code or any
local authorities having jurisdiction (AHJ).
Wiring Considerations
In a four-wire system, the maximum loop length and
number of bases that can be placed on a loop depend
on the voltage drop on the power circuit. Use standard
voltage drop calculations to ensure that the last
detector on the loop has at least 16 V when all
sounders and relays are powered.
Parts included
Region
Certification
USA
UL
ULSZ: Audible Signal Appliances
(UL464), UQGS: Heat-automatic Fire
Detectors (ANSI/UL 521), UROX: Smoke
- Automatic Fire Dectectors (UL268),
UROX7: Smoke - Automatic Fire Dectectors Certified for Canada (ULC-S529)
FM
F220-B6RS
CSFM
see our website
NYCMEA
117-05-E
Quant.
Component
1
Detector base
1
Literature pack
Technical specifications
Electrical
Voltage Range:
16.0 VDC to 30 VDC
Alarm Current
Installation/configuration notes
6-wire mode (4-wire base + two sounder power wires)
Compatibility Information
Four‑wire: Compatible with all UL Listed four‑wire
control panels. Refer to the control panel's Installation
Instructions for proper end‑of‑line (EOL) resistor
selection.
Detectors: Compatible with the following F220 Series
Detector Heads:
Relay:
The relay draws 15 mA in alarm.
Steady Sounder:
24 VDC: 30 mA; 30 VDC: 35 mA
• F220‑P Photoelectric Smoke Detector
• F220‑PTH Photoelectric Smoke Detector with +135°F
(+57°C) Heat Sensor
• F220‑PTHC1 Photoelectric Smoke Detector with
+135°F (+57°C) Heat Sensor and Carbon Monoxide
Sensor Enhancement1
• F220‑135 Electronic Rate‑of‑Rise, Fixed Temperature
+135°F (+57°C) Heat Detector
• F220‑135F Electronic Fixed Temperature +135°F
(+57°C) Heat Detector
• F220‑190F Electronic Fixed Temperature +190°F
(+88°C) Heat Detector
The F220‑PTHC detects carbon monoxide (CO) as a
component of a fire. It is not a CO detector and cannot
activate an alarm in the presence of CO only.
1
Mounting Considerations
Depending on local regulations, surface mount the
bases using anchors, mollies, or wing nuts, or mount
directly on four‑inch square or octagonal electrical
boxes or single‑gang switch boxes.
4-wire mode
With Steady Sounder and
Relay:
24 VDC: 45 mA; 30 VDC: 50 mA
Standby Current (base
only):
30 VDC: 10 mA maximum
Environmental
Relative Humidity:
0 to 95%, non‑condensing; 15% to 95%,
non‑condensing when used with CO
sensor model
Temperature (operating):
+32°F to +100°F (0°C to +38°C)
Mechanical
Color:
Off-white
Dimensions (diameter x
thickness)
6 in. x 0.9 in. (15.2 cm x 2.3 cm)
Material:
Fire‑resistant plastic
Outputs
Relay Type:
Normally‑open (NO) Form A
Relay Rating:
0.5 A at 120 VDC or 120 VAC
Sounder Output:
>85 dB at 10 ft (3 m)
3 | F220‑B6RS 24 VDC Four‑wire Detector Base with Sounder
Ordering information
F220‑B6RS 24 VDC Four‑wire Detector Base with Sounder
Four-wire detector base with sounder for use with the
F220 Photoelectric Smoke and Heat Detectors.
Order number F220-B6RS
Represented by:
Americas:
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 800 289 0096
Fax: +1 585 223 9180
security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
5617 BA Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
emea.securitysystems@bosch.com
www.boschsecurity.com
© Bosch Security Systems 2014 | Data subject to change without notice
2707923211 | en, V5, 07. Aug 2014
Asia-Pacific:
Robert Bosch (SEA) Pte Ltd, Security
Systems
11 Bishan Street 21
Singapore 573943
Phone: +65 6571 2808
Fax: +65 6571 2699
apr.securitysystems@bosch.com
www.boschsecurity.asia
China:
America Latina:
Bosch (Shanghai) Security Systems Ltd. Robert Bosch Ltda Security Systems Division
201 Building, No. 333 Fuquan Road
Via Anhanguera, Km 98
North IBP
CEP 13065-900
Changning District, Shanghai
Campinas, Sao Paulo, Brazil
200335 China
Phone: +55 19 2103 2860
Phone +86 21 22181111
Fax: +55 19 2103 2862
Fax: +86 21 22182398
latam.boschsecurity@bosch.com
www.boschsecurity.com.cn
www.boschsecurity.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising