adhesive quick check chart
ADHESIVE QUICK CHECK CHART
SUBFLOOR TYPE
^Existing
Resilient
Flooring
**Existing
Ceramic or
Terrazzo Floors
Wafer, Flake,
Chip, Particle
or Similar
Board
Existing
Softwood or
Hardwood
Floors
AD-530SF
AD-529SF
AD-530SF
N/R
N/R
AD-530SF
AD-529SF
AD-530SF
N/R
N/R
AD-530SF
PS-30
N/R
N/R
DS-100
DS-100
N/R
N/R
PS-30
PS-30
N/R
N/R
#Existing
Softwood or
Hardwood
Steps
AD-529SF
AD-530SF
*Suspended
Concrete
*On Grade
Concrete
*Below Grade
Concrete
Suspended
Plywood
^^^Metal Floors
^^Radiant
Heated Floors
(Concrete)
Mohawk Rubber Tiles and
Medi-Flex Sheets
AD-777
AD-529SF
AD-530SF
AD-777
AD-529SF
AD-530SF
AD-777
AD-529SF
AD-530SF
AD-777
AD-530SF
AD-530SF
AD-777
AD-529SF
AD-530SF
Medi-Flex TRUE Tiles and
SheetsI
AD-777
AD-529SF
AD-530SF
AD-777
AD-529SF
AD-530SF
AD-777
AD-530SF
AD-530SF
AD-777
AD-529SF
AD-530SF
AD-530SF
PS-30
AD-530SF
PS-30
AD-530SF
PS-30
AD-530SF
PS-30
AD-530SF
PS-30
AD-530SF
PS-30
PS-30
DS-100
DS-100
DS-100
DS-100
DS-100
DS-100
PS-30
AD-610
PS-30
AD-610
PS-30
AD-610
PS-30
AD-610
PS-30
AD-610
AD-610
Note: PS-30 Adhesive for residential applications only
AD-777
AD-529SF
AD-530SF
Note: For demanding applications such as underneath patients’ beds, OR’s, ER’s, use AD-530SF and consult your representative for details.
Luxury Vinyl Tile
Ultimate Step
PVC-FREE:
- Stonewalk
If PVC-FREE flooring is to be installed over a porous surface in an area where there are heavy rolling
loads or where room temperatures will reach 32°C (90°F) AD-610 MUST be used.
*Concrete
Steps
Plywood
Steps
Metal Steps
Existing
Resilient Steps
**Existing
Ceramic or
Terrazzo Steps
Wafer, Flake,
Chip &
Particle
Board Steps
AD-777, AD-529SF, AD-530SF
AD-777,
AD-529SF,AD-530SF
AD-530SF
N/R
AD-529SF
AD-530SF
N/R
ACCESSORIES
Commercial Rubber
Treads, Risers
Wall Base & Stringers
Use a good quality solvent-free wall base adhesive.
N/R – not recommended
*
Ensure moisture tests have been conducted and that levels comply with manufacturer’s specifications and will not increase in the future. For all grade installations (on, above or below), it is the flooring contractor’s responsibility to ensure that moisture and pH levels in
the concrete comply with specifications. Mohawk Group is not responsible for hydrostatic pressure that may occur in the future.
**
Glaze, polished finishes, wax and sealers on the existing floor must be removed prior to installation. Consult Technical Services for specific details 1-800-479-0190.
^
Although these adhesives and products can be used over existing resilient flooring, Mohawk Group will not honor any claims relating to bond failure. Mohawk Group recommends that the existing resilient flooring be removed.
^^
Rubber is a natural insulator that will create a heat barrier over radiant heat flooring.
^^^
Floor must not flex or move. Consult Technical Services for specific details 1-800-479-0190.
#
All wax and polish residue must be removed prior to installation.
Mohawk Group, 1975 West Oak Circle, Marietta GA, 30062
Phone: 800-554-6637
Customer Service 877-235-0453
Customer Service Fax 877-244-8054
Samples 888-740-6936
Installation / Maintenance 800-833-6954
Website : www.mohawkgroup.com
6016-M (2012-09-07)
Page 1 of 3
ADHESIVE QUICK CHECK CHART
ADHESIVES
PS-30
and/or
DS-100
Pressure-Sensitive Adhesive
AD-33
Solvent-Free Epoxy Stair Nosing
Caulking
AD-777
AD-529SF
AD-530SF
SUBFLOOR TYPE
TROWEL SPECIFICATION
APPROXIMATE COVERAGE
Porous Subfloor
1.6 mm x 0.8 mm x 0.8 mm (1/16x1/32x1/32)
U-notched trowel
Up to 18.6 sq. m / 3.79 liter unit (up to 200 sq. ft. / U.S. gallon)
Non-porous Subfloor
1.6 mm x 0.8 mm x 0.8 mm (1/16x1/32x1/32)
U-notched trowel
Up to 23.2 sq. m / 3.79 liter unit (up to 250 sq. ft. / U.S. gallon)
For concrete, wood or metal
Porous Subfloor
1.6 mm X 0.8 mm x 0.8 mm (1/16x1/32x1/32)
U-notched trowel
Up to 18.6 sq. m / 3.79 liter unit (up to 200 sq. ft. / U.S. gallon)
Non-porous Subfloor
1.6 mm x 0.8 mm x 0.8 mm (1/16x1/32x1/32)
U-notched trowel
Up to 23.2 sq. m / 3.79 liter unit (up to 250 sq. ft. / U.S. gallon)
Porous Subfloor
1.6 mm X 1.6 mm x 1.6 mm (1/16x1/16x1/16)
U-notched trowel
Up to 15.0 sq. m / 3.79 liter unit (up to 160 sq. ft. / U.S. gallon)
Non-porous Subfloor
1.6 mm x 0.8 mm x 0.8 mm (1/16x1/32x1/32)
U-notched trowel
Up to 18.6 sq. m / 3.79 liter unit (up to 200 sq. ft. / U.S. gallon)
Porous Subfloor
1.6 mm X 1.6 mm x 1.6 mm (1/16x1/16x1/16)
U-notched trowel
Up to 15.0 sq. m / 3.79 liter unit (up to 160 sq. ft. / U.S. gallon)
Non-porous Subfloor
1.6 mm x 0.8 mm x 0.8 mm (1/16x1/32x1/32)
U-notched trowel
Up to 18.6 sq. m / 3.79 liter unit (up to 200 sq. ft. / U.S. gallon)
Porous Subfloor
1.6 mm x 0.8 mm x 0.8 mm (1/16x1/32x1/32)
U-notched trowel
Up to 18.3 sq. m / 3.79 liter unit (up to 200 sq. ft. / U.S. gallon)
Acrylic PSA/Wet-Set Adhesive
Solvent-Free Epoxy Adhesive
Solvent-Free Polyurethane Adhesive
AD-610
Acrylic Wet-Set Adhesive
Durabond
Cold welding system for rolled rubber
Up to 15.0 lin. m / 6 mm bead (up to 50 lin. ft. / ¼” bead)
50 ml (1.7 fl oz) cartridge
Up to 12.2 lin. m / cartridge (up to 40 lin. ft. / cartridge)
*TROWEL SPECIFICATION CODE: WIDTH/DEPTH/SPACING
Mohawk Group, 1975 West Oak Circle, Marietta GA, 30062
Phone: 800-554-6637
Customer Service 877-235-0453
Customer Service Fax 877-244-8054
Samples 888-740-6936
Installation / Maintenance 800-833-6954
Website : www.mohawkgroup.com
6016-M (2012-09-07)
Page 2 of 3
ADHESIVE QUICK CHECK CHART
MOISTURE & pH LEVELS SPECIFICATIONS FOR ADHESIVES ON ALL GRADES
ADHESIVES
ANHYDROUS CALCIUM CHLORIDE TEST
RELATIVE HUMIDITY TEST
ASTM F 1869
ASTM F 2170
Moisture vapor emission must not exceed stated amount
below in
Relative Humidity (RH) must not exceed
Amount listed below (%)
kg / 100 sq. m / 24 hours (lbs / 1,000 sq. ft. / 24 hours)







pH TEST
ASTM F 710
5.3.1
Test
Procedure
5.3.1
PS-30
0 – 2.26 kg (0 - 5.0 lbs)
80%
8 -10
DS-100
0 – 2.26 kg (0 - 5.0 lbs)
80%
8 -10
AD-33
0 - 1.36 kg (0 - 3.0 lbs)
80%
8 -10
AD-777
0 - 2.26 kg (0 - 5.0 lbs)
80%
8 -10
AD-529SF
0 – 2.26 kg (0 - 5.0 lbs)
80%
8 -10
AD-530SF
0 – 2.26 kg (0 – 5.0 lbs)
80%
8 -10
AD-610
0 – 2.26 kg (0 - 5.0 lbs)
80%
8 -10
Good quality rubberized asphalt emulsion
adhesive
0 – 2.26 kg (0 – 5.0 lbs)
75%
8 -10
REFER TO THE LATEST VERSION OF THE ASTM SPECIFICATIONS FOR SPECIFIC TESTING PROCEDURE.
pH TEST AND BOTH MOISTURE TESTS MUST BE PERFORMED AND RESULTS WITHIN SPECIFICATIONS BEFORE INSTALLATION.
IT IS THE FLOORING CONTRACTOR’S RESPONSIBILITY TO ENSURE THAT MOISTURE AND pH LEVELS IN THE CONCRETE COMPLY WITH SPECIFICATIONS.
FREQUENCY OF TESTS IS 3 TESTS FOR THE FIRST 1,000 SQ. FT. AND ONE TEST PER ADDITIONAL 1,000 SQ. FT.
REFER TO THE “FLOOR PREPARATION INSTRUCTIONS” AND “INSTALLATION INSTRUCTIONS” DOCUMENTS FOR SPECIFIC PREPARATION & INSTALLATION DETAILS.
MOHAWK GROUP WILL NOT BE HELD RESPONSIBLE FOR HYDROSTATIC PRESSURE THAT MAY OCCUR IN THE FUTURE.
IMPORTANT NOTICE: DO NOT USE CHEMICAL ADHESIVE REMOVAL PRODUCTS (CHEMICAL ABATEMENT PRODUCTS). THEIR USE WILL VOID MOHAWK GROUP’S ADHESIVE SYSTEM WARRANTY.
Mohawk Rubber Slate, Hammered, Infused, Natural Slate, and Round, Commercial Rubber Accessories, Medi-Flex, Medi-Flex II, Medi-Flex TRUE, Stonewalk, Luxury Vinyl Tile, Ultimate Step and the adhesive systems: PS-30, AD-33, DS-100, AD-777, AD-529SF,
AD-530SF and AD-610 are registered trademarks of Mohawk Group.
Mohawk Group, 1975 West Oak Circle, Marietta GA, 30062
Phone: 800-554-6637
Customer Service 877-235-0453
Customer Service Fax 877-244-8054
Samples 888-740-6936
Installation / Maintenance 800-833-6954
Website : www.mohawkgroup.com
6016-M (2012-09-07)
Page 3 of 3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising