Eaton® SPD Series Surge Protective

Eaton® SPD Series Surge Protective
Instruction Manual IM01005032E
Effective June 2014
Rev. 2
Eaton SPD Series
Table of Contents
1.0Introduction
2.0Installation
3.0Operating Features
4.0Troubleshooting
5.0Specifications
6.0Ordering Guidelines
7.0Warranty
Eaton SPD Series
Instruction Manual IM01005032E - Rev. 2
Effective June 2014
1.0 Introduction
WARNING
1.1 Manual Organization
This Installation Manual describes the safe installation, testing
and operation of the Eaton® SPD Series Surge Protective Device
(SPD).
ARC FLASH DURING INSTALLATION COULD CAUSE INJURY. USE
APPROPRIATE SAFETY PRECAUTIONS AND EQUIPMENT FOR ARC
FLASH PROTECTION.
This manual is organized into seven sections, as follows:
1.4 Catalog Numbering System
1.0 Introduction
2.0 Installation
3.0 Operating Features
4.0 Troubleshooting
Each Eaton SPD Series unit has a name plate that identifies
the parameters used for manufacture. These parameters are
expressed in letters and numbers, to reflect the Series, kA
Rating, Voltage Code, Feature Package, and Application as
shown in Table 1.
5.0 Specifications
6.0 Ordering Guidelines
7.0 Warranty
Table 1. Catalog Numbering System
PSPD
1.2 Product Overview
The Eaton SPD Series protects critical electrical and electronic
equipment from damage by power surges. This is done by
shunting high energy lightning surges (and other transient disturbances) away from the equipment being protected. It does
this in nanoseconds by providing a low impedance surge path to
ground while supporting power frequency voltage.
The Eaton SPD Series is designed to mount on the wall (or other
vertical surface) as close as possible to the electrical cabinet.
The SPD Series is available in AC, surge current capacity ratings
from 50kA to 400kA, NEMA 1 enclosures.
The Eaton SPD Series is available in three feature packages (Basic, Standard, and Standard with Surge Counter), as
described in Section 3, "Operating Features." Each model is available in Delta, Wye, and Split Phase wiring configurations.
All Eaton SPD Series models have been tested and certified
by Canadian Standards Association to comply with ANSI/UL
Standard 1449, 3rd Edition.
1.3 Safety Precautions
A licensed/qualified electrician must complete all instructions
in this manual in accordance with the National Electric Code
(NEC®), state, and local codes, or other applicable country
codes. All applicable local electrical codes supersede these
instructions.
Series
250 480D 2 K
Voltage Code
kA Rating
SPD = __SPD model,
250 = the kA rating (50 – 400 kA),
480D = the voltage,
2 = the feature package (Basic, Standard, Standard With Surge
Counter), and,
K = the Application Suffix (NEMA 1 with or without an internal
disconnect).
These numbers appear as part of the product label attached to
the front left side of the SPD. See Figure 1.
IMPROPER INSTALLATION COULD CAUSE DEATH, INJURY AND
EQUIPMENT DAMAGE. FOLLOW ALL WARNINGS AND CAUTIONS.
COMPLETELY READ AND UNDERSTAND THE INFORMATION IN THIS
INSTRUCTION MANUAL BEFORE ATTEMPTING TO INSTALL OR OPERATE THIS EQUIPMENT.
IMPROPER WIRING COULD CAUSE DEATH, INJURY AND/OR EQUIPMENT DAMAGE. ONLY LICENSED/QUALIFIED ELECTRICIANS WHO ARE
TRAINED IN THE INSTALLATION AND SERVICE OF ELECTRICAL SERVICES ARE TO INSTALL AND SERVICE THIS EQUIPMENT.
HAZARDOUS VOLTAGES ARE PRESENT INSIDE THE SPD DURING
NORMAL OPERATION. FOLLOW ALL SAFE WORK PRACTICES TO AVOID
ELECTRICAL SHOCK.
Figure 1. Product Label
Eaton www.eaton.com
Feature Package
For example, a 480 volt Delta (3-wire plus Ground) for use in an
NEMA 1 application requires an SPD model SPD 250480D2K,
where:
WARNING
2
Application
Eaton SPD Series
Instruction Manual IM01005032E - Rev.2
Effective June 2014
1.5 Equipment Testing
NOTICE
WARNING
CONDUCTING DIELECTRIC, MEGGER, OR HI-POTENTIAL TESTING
WITH THE SPD INSTALLED WILL CAUSE INTERNAL DAMAGE TO THE
SPD. THE SPD WILL ALSO CAUSE THE TEST TO FAIL.
Every Eaton SPD Series unit is tested at the factory for dielectric breakdown. No further SPD testing is required for installation.
If you desire to test distribution equipment by performing
dielectric, megger, or hi-potential tests, any installed SPD must
be disconnected from the power distribution system to prevent
damage to the unit.
Follow this procedure to safely disconnect the SPD:
1. For SPDs connected to a circuit breaker or fuse:
a. 3-wire delta SPDs: Turn off the circuit breaker or remove
the fuses from the fuse holder to isolate the SPD.
b. Wye and Split phase SPDs: Turn off the circuit breaker or
remove the fuses from the fuse holder to isolate the SPD
and remove the Neutral connection on Wye connected
SPDs.
2.0 Installation
WARNING
A POOR GROUND, OR GROUNDING/BONDING VIOLATIONS, COULD
PREVENT THE SPD FROM PERFORMING AS SPECIFIED.
DO NOT USE THE SPD TO CARRY OR PASS THROUGH GROUND TO
OTHER DEVICES OR LEADS. DAMAGE TO THE EQUIPMENT MAY
RESULT.
•
Check the facility grounding system. All grounding, bonding,
and earthing must meet the NEC and any other national, state
and local electrical codes.
2.2 Installation Locations
Eaton's SPD Series can be installed next to, above, or below any
existing electrical enclosure.
The ideal mounting location for the Eaton SPD Series is as close
as possible to the electrical enclosure. The Eaton SPD Series
should be mounted in such a way as to minimize any sharp
bends in the wiring conduit.
2.3 Installation Procedures
1. Before mounting the SPD first determine the ideal location
and ensure that the mounting surface is sufficient to support the weight of the SPD (See Figures 2 and 3 on page 4
for model weights). The SPD should be mounted as close a
possible to the electrical enclosure and as close as possible
to the wiring connection point within the enclosure. This will
ensure a minimum wire length and maximum SPD performance.
INSTALLING AN SPD THAT IS IMPROPERLY RATED FOR THE ELECTRICAL SYSTEM VOLTAGE COULD CREATE A POTENTIALLY HAZARDOUS
CONDITION, RESULTING IN INJURY OR EQUIPMENT DAMAGE.
2. Lay out the four enclosure mounting holes using the enclosure dimensions provided in Figures 2 and 3 on page 4. Drill
the appropriate holes per the product dimensions. Note:
NEMA 1 enclosures require a #10 fastener.
2.1 Preparation for Installation
3. Determine the correct length and install metal conduit onto
the SPD. NEMA 1 SPDs have a 3/4 inch trade size chase nipple. Route all Phase, Neutral (where applicable), Ground and
Form C (where applicable) wires through the conduit.
CAUTION
EATON SPD SERIES PRODUCTS MUST BE INSTALLED OR REPLACED
BY A QUALIFIED ELECTRICIAN TO AVOID INJURY OR EQUIPMENT
DAMAGE.
Before installing an Eaton SPD Series unit, do the following:
•
Verify that the area is clear of any dirt, debris or clutter that
may hamper the installation process.
•
Verify that there is enough space to install the SPD. See
Section 2.3, "Installation Procedures" for dimensions.
•
Confirm that all tools and equipment needed for the installation are available.
•
Confirm that the system voltage and wiring configuration is
the same as the SPD you are installing. Check the voltage
rating label on the side of the SPD.
WARNING
TURN OFF THE POWER SUPPLY BEFORE WORKING IN ANY ELECTRICAL CABINET OR ON ANY CIRCUIT BREAKER PANEL. FAILURE TO DO
SO COULD RESULT IN INJURY OR DEATH FROM ELECTRICAL SHOCK.
4. Determine the hole location on the receiving electrical enclosure and either remove the knock-out provided or drill the
appropriate size hole at this location. Route the SPD wires
through the enclosure hole and mount the SPD enclosure.
5. Select the correct wiring diagram for the SPD you are installing. You must refer to this diagram while wiring the SPD. See
Figures 5, 6, and 7 on page 5.
6. Determine the wire length required to make the SPD Phase
connections and cut the wires to the appropriate length. (To
maximize SPD performance, wire length should be as short
as possible). Connect the Phase wires.
NNote: For wire lengths longer than 4 inches, Phase wires should
be twisted once for each 4 inches of wire length to maximize SPD
performance.
7. Determine the wire length for the Ground and Neutral (where
applicable) wires and cut these wires as needed. Again, keep
these wires as short as possible to maximize SPD performance.
8. Standard and Standard with Surge Counter SPDs also provide wiring for Form C relay contacts. This connection can be
used for remote monitoring of the SPD. The Form C contacts
are rated at 150V AC or 125V DC at 1A. Make the remote
monitoring connections per the Form C wiring diagram in
Figure 4. Follow all national, state and local electrical codes
when making these connections.
Eaton www.eaton.com
3
Eaton
SPDManual
Series IM01005032E - Rev. 2
Instruction
For
Mounting
Effective June 2014 ExternalTo
Electrical Distribution Equipment
IM01005031E Rev. 2
Effective
November
Figure 2.
NEMA 1 2012
(Suffix K))
Figure 3. NEMA 1 (Suffix K)
IM01005031E
Rev. 2
Eaton SPD Series
Effective November 2012
Eaton SPD Series
For Mounting External To
Electrical Distribution Equipment
Figure5.3.NEMA
NEMA11(With
(WithDisconnect)
Disconnect)(Suffix
(SuffixM)
M)
Figure
Figure 4. NEMA 4 - 4X (Suffix N, P)
4
Eaton www.eaton.com
eaton corporation www.eaton.com
5
Eaton SPD Series
Instruction Manual IM01005032E - Rev.2
Effective June 2014
BLUE / WHITE
COMMON
RED / WHITE
NORMALLY OPEN
ORANGE / WHITE
NORMALLY CLOSED
Figure 4. Sidemount Form C Wires
Figure 7. 3-Phase Wye Units
Figure 5. Split Phase Units
Figure 6. 3-Phase Delta
Eaton www.eaton.com
5
Eaton SPD Series
Instruction Manual IM01005032E - Rev. 2
Effective June 2014
3.0 Operating Features
3.2.2 Standard Feature Package
3.1 General
The Eaton SPD Series Standard Feature Package display is
shown in Figure 9.
The Eaton SPD Series comes in three feature packages: Basic,
Standard, and Standard with Surge Counter. The operating specifics of each feature package are described below.
The Eaton SPD Series requires no operator involvement, other
than to monitor the display panel to determine status of the
SPD.
After system power is applied, the SPD automatically begins
protecting downstream electrical equipment from voltage transients.
Some SPD units have a Form C relay contact that allows for the
remote indication of SPD status. Form C contact wires are permanently connected to the SPD.
3.2 Displays and Indicators
All Eaton SPD Series units (Basic, Standard, and Standard With
Surge Counter) use a display panel to indicate system status.
The display panel is slightly different for each feature package.
Each display has both green and red light emitting diodes (LEDs)
to indicate the status of the protection on each phase. Green
indicates the phase is fully protected. Red indicates a loss of
protection. Wye, Split Phase and High-Leg Delta units have an
additional set of green/red LEDs to indicate status of Neutral/
Ground protection.
Figure 9. Standard Feature Package Display
The Standard Feature Package has the following features:
•
All features of the Basic Feature Package.
•
One Form C relay contact rated at 150Vac or 125Vdc @1A.
When the LEDs turn red, an audible alarm will also sound on
units equipped with an audible alarm.
Specific operating conditions displayed for each Eaton SPD
Series Feature Package are described below.
3.2.1 Basic Feature Package
The Eaton SPD Basic Feature Package display is shown in Figure
8.
•
Normal operating conditions. N.O. = OPEN. N.C =
CLOSED.
•
Loss of protection on any phase or loss of power. N.O. =
CLOSED. N.C. = OPEN.
•
Audible alarm with Reset push button.
•
EMI/RFI filtering.
3.2.3 Standard With Surge Counter Feature Package
The Eaton SPD Series Standard With Surge Counter Feature
Package display is shown in Figure 10.
Figure 8. Basic Feature Package Display
The Basic Feature Package has the following features:
•
•
6
Green LEDs: Illumination indicates the phase is fully protected, and operating normally, with all protection active and
available. Green LEDs also indicate Neutral to Ground protection on units with a Neutral wire. Green LEDs do not indicate
on/off status of power.
Red LEDs: Illumination indicates a loss of protection, and that
one or more protective devices are now inactive and unavailable for that Phase. Red LEDs also indicate Neutral to Ground
protection on units with a Neutral wire. Red LEDs do not indicate on/off status of power.
Eaton www.eaton.com
Figure 10. Standard With Surge Counter Feature Package
Display
The Standard With Surge Counter Feature Package has the following features:
•
All features of the Standard Feature Package.
•
LCD screen that displays surge count.
•
Reset button to RESET the surge counter to zero.
Eaton SPD Series
Instruction Manual IM01005032E - Rev.2
Effective June 2014
3.2.4 SPD Display Rotation
4.0 Troubleshooting
The SPD display can be rotated on the SPD enclosure, up to 360
degrees. This allows you to position the display for the best visibility regardless of the position in which the SPD is installed.
Many SPD failures result from improper installation. Once the
SPD is installed properly, it is a highly reliable unit.
Rotations are at 90, 180, and 270 degrees.
Reposition the SPD display as follows:
1. Remove power from the unit.
2. Remove and discard the perforated overlay material at the two opposite corners of the display.
3. Remove the two phillips head screws that hold the display.
If the SPD does not function properly, first confirm that it is
installed properly. See Section 2, “Installation.”
If the SPD malfunctions after it has been operating routinely,
refer to Table 2, Troubleshooting Chart. This Troubleshooting
Chart identifies possible causes and solutions to the malfunction. Further assistance may be obtained by calling Eaton’s
Applications Engineers, at 1-800-809-2772, option 4, sub-option
2, including being directed to the warranty process if applicable.
4. Rotate the display to the desired position. Be careful not to overstress the display ribbon cable.
5. Place the display back onto the SPD enclosure. Again, be careful not to overstress or crimp the ribbon cable.
6. Replace the two phillips head screws. Tighten screws to 1.35 Nm (12 in-lbs).
7. Restore power to the unit.
Table 2. Troubleshooting Chart
Condition
Probable Cause
Solution
Green LEDs ON (1 per phase) and one Green LED ON for
Neu/Gnd Protection
Normal operation
N/A.
Audible Alarm OFF, Form C (N.C.) contact in the CLOSED
state
Normal operation
N/A.
Phase Green LED is OFF, same Phase Red LED is ON,
Audible Alarm is ON
Phase protection compromised or lost
Replace SPD
Extended Temporary Overvoltage (TOV)
Check electrical system for TOV sources, correct, replace SPD
Significant surge event
Replace SPD
Neu/Gnd Green LED is OFF, Neu/Gnd Red LED is ON,
Audible Alarm is ON (for models with Neutral connections)
Neu/Gnd protection is compromised or lost
Replace SPD
Significant surge event
Replace SPD
All phase Green LEDs OFF, all phase RED LEDs ON, Audible
Alarm is ON
All phase protection is compromised or lost
Replace SPD
SPD rated voltage is less than system voltage
Replace SPD with correct voltage model
Extended Temporary Overvoltage (TOV)
Check electrical system for TOV sources, correct, replace SPD
Significant surge event
Replace SPD
Audible Alarm Silence button has been
depressed and Alarm is silenced
Normal operation
SPD is not connected to a power source
Check system voltage at SPD connection
One of the display Red LEDs is ON. Audible Alarm is OFF
All Green and Red LEDs are OFF, LCD display (on Surge
Counter models) is OFF
If power is cycled and a fault condition still exists, the Audible
Alarm will reactivate
Check SPD connections
Eaton www.eaton.com
7
Instruction Manual IM01005032E - Rev. 2
Eaton SPD Series
Effective June 2014
5.0 Specifications
Table 3. Specifications
Description
Specification
Surge current capacity per phase
50, 80, 100, 120, 160, 200, 250, 300, 400 kA ratings available
Nominal discharge current (In)
20kA
Short circuit current rating (SCCR)
200kA
SPD Type
Basic feature package = Type 1 (can also be used in Type 2 applications)
Standard and Standard with Surge Counter feature packages = Type 2
Enclosure Types
NEMA 1
Standard split phase voltages available
120/240
Three phase wye system voltages available
120/208, 230/400, 277/480,
Three phase delta system voltages
240, 480
Phase wire length
48” of 10AWG extend beyond the conduit hub
Relay wire length (optional)
48” of 14AWG extend beyond the conduit hub
RoHS Compliant
Yes
Internal Disconnect (optional)
Eaton 30 Amp FDC Circuit Breaker, Type MCCB
Input Power Frequency
50/60 Hz
Power consumption (Basic units)
208Y, 240S, 240D, voltage codes
0.5W
400Y, 480Y and 480D voltage codes
1.1W
Power consumption (Standard and Standard with Surge Counter units)
208Y, 240S, 240D, voltage codes
0.6W
400Y, 480Y, and 480D Basic voltage codes
1.7W
Protection modes
Maximum continuous operating voltage (MCOV)
208Y, 240S voltage codes
Single split phase ...L-N, L-G, N-G, L-L Three phase delta...L-G, L-L
Three phase Wye.....L-N, L-G, N-G, L-L
150 L-N,150 L-G, 150 N-G, 300 L-L
400Y and 480Y voltage codes
320 L-N, 320 L-G, 320 N-G, 640 L-L
240 D voltage code
320 L-G, 320 L-L
480 D voltage code
640L- L-G, 640 L-L
Ports
1
Operating temperature
-20 through 50C (-4 through 122F)
Operating humidity
5% through 95%, non-condensing
Weight
Reference Figures 2 and 3 on page 4
Form C relay contact ratings
150 Vac or 125 Vdc, 1A maximum
Form C relay contact loogic
Power on, normal state - NO contact = OPEN, NC contact = CLOSED
Power off, fault state, - NO contact = CLOSED, NC contact = OPEN
EMI/RFI filtering attenuation (Standard and Standard With Surge Counter
Up to 50 dB from 10 kHz to 100 MHz
Agency certifications and approvals
CSA Listed to ANSI/UL1449 3rd Edition
CSA Std. C22.2 No. 8-M1986.
Warranty
10 Years, 15 Years if the product is properly registered with Eaton at www.eaton.com/spd
8
Eaton www.eaton.com
Eaton SPD Series
Instruction Manual IM01005032E - Rev.2
Effective June 2014
6.0 Ordering Guidelines
Table 4. Eaton SPD Series
PSPD 250 480D
2 K
SPD
kA Rating
Voltage Code
Options
50kA Per Phase
80kA Per Phase
100kA Per Phase
120kA Per Phase
160kA Per Phase
200kA Per Phase
250kA Per Phase
300kA Per Phase
400kA Per Phase
Options
Sidemount Units
240S = 120/240 Split Phase
208Y = 120/208 Wye (4W + G)
400Y = 230/400 Wye (4W + G)
480Y = 277/480 Wye (4W + G)
240D = 240 Delta (3W + G)
480D = 480 Delta (3W + G)
Application Suffix
Feature Package
Options
Options
1 = Basic.
Sidemount Units
Dual colored LED per Phase to indicate Protection status
Dual colored LED to indicate protection status of the N-G Mode on
units with a Neutral Wire
2 = Standard.
Dual colored LED Per Phase to indicate Protection Status
Dual colored LED to indicate Protection Status of the N-G Mode on
units with a Neutral Wire
Audible alarm with Silence button
Form 'C' Relay Contact. See Table 4 Specifications
EMI/RFI filtering Providing up to 50dB of Noise Attenuation from
10KHz to 100Mhz
3 = Standard With Surge Counter
Dual colored LED Per Phase to indicate Protection Status
Dual colored LED to indicate Protection Status of the N-G Mode on
units with a Neutral Wire
Audible alarm with Silence button
Form 'C' Relay Contact
EMI/RFI filtering Providing up to 50dB of Noise Attenuation from
10kHz to 100Mhz Surge Counter with Reset Button
K = NEMA 1 Enclosure
M = NEMA 1 Enclosure With Internal Disconnect
Example: PSPD250480D2K = SPD Series, 250kA Per Phase, 480D Voltage, Standard Feature Package, NEMA 1 Sidemount Application.
Eaton www.eaton.com
9
Instruction Manual IM01005032E - Rev. 2
Effective June 2014
7.0 Warranty
Eaton warrants these products for a period of 10 years from
the date of delivery to the purchaser , 15 years if the product is
properly registered with Eaton, to be free from defects in both
workmanship and materials. Eaton assumes no risk or liability
for results of the use of the products purchased from it, including but without limiting the generality of the foregoing: (1) The
use in combination with any electrical or electronic components,
circuits, systems, assemblies, or any other materials or substances; (2) Unsuitability of any product for use in any circuit or
assembly.
Purchaser’s rights under the warranty shall consist solely of
requiring Eaton to repair, or at Eaton's sole discretion, replace,
free of charge, F.O.B. factory, and defective items received at
said factory within said term determined by Eaton to be defective. The giving of or failure to give any advice or recommendations by Eaton shall not constitute any warranty by or impose
any liability upon Eaton. The foregoing constitutes the sole and
exclusive liability of Eaton AND IS IN LIEU OF ANY AND ALL
OTHER WARRANTIES EXPRESSED, IMPLIED OR STATUTORY
AS TO THE MERCHANTABILITY, FITNESS FOR PURPOSE SOLD,
DESCRIPTION, QUALITY, PRODUCTIVENESS OR ANY OTHER
MATTER.
In no event shall Eaton be liable for special or consequential
damages or for delay in performance of the warranty.
This warranty does not apply if the product has been misused,
abused, altered, tampered with, or used in applications other
than specified on the nameplate. At the end of the warranty
period, Eaton shall be under no further warranty obligation
expressed or implied.
The product covered by this warranty certificate can only be
repaired or replaced by the factory. For help on troubleshooting
the SPD, or for warranty information, call 1-800-809-2772, Option
4, sub-option 2. Repair or replacement units will be returned collect. If Eaton finds the return to be a manufacturer’s defect, the
product will be returned prepaid.
10
Eaton www.eaton.com
Eaton SPD Series
Eaton SPD Series
Instruction Manual IM01005032E - Rev.2
Effective June 2014
Eaton www.eaton.com
11
Instruction Manual IM01005032E - Rev. 2
Eaton SPD Series
Effective June 2014
Copyright © 2014 by Eaton, Moon Township, PA, USA. All rights
reserved. No part of this document may be reproduced in any way
without the express written approval of Eaton.
Specifications contained herein are subject to change without
notice.
EATON - CONFIDENTIAL AND PROPRIETARY NOTICE TO
PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL
INFORMATION IN THIS DOCUMENT, INCLUDING THE DRAWING
AND INFORMATION CONTAINED THEREON, IS CONFIDENTIAL
AND IS THE EXCLUSIVE PROPERTY OF EATON, AND IS MERELY
ON LOAN AND SUBJECT TO RECALL BY EATON AT ANY TIME.
BY TAKING POSSESSION OF THIS DOCUMENT, THE RECIPIENT
ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT
BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF
EATON, AND THAT NO PORTION OF THIS DOCUMENT MAY BE
COPIED OR OTHERWISE REPRODUCED WITHOUT THE PRIOR
WRITTEN CONSENT OF EATON. IN THE CASE OF CONFLICTING
CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE
STATUS OF THIS DOCUMENT.
DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY
The information, recommendations, descriptions and safety notations in this document are based on Eaton's ("Eaton") experience
and judgment and may not cover all contingencies. If further information is required, an Eaton sales office should be consulted. Sale
of the product shown in this literature is subject to the terms and
conditions outlined in appropriate Eaton selling policies or other
contractual agreement between Eaton and the purchaser. THERE
ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF
FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY,
OTHER THAN THOSE SPECIFICALLY SET OUT IN ANY EXISTING
CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT
STATES THE ENTIRE OBLIGATION OF EATON. THE CONTENTS OF
THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY
ANY CONTRACT BETWEEN THE PARTIES.
In no event will Eaton be responsible to the purchaser or user in
contract, in tort (including negligence), strict liability or otherwise
for any special, indirect, incidental or consequential damage or loss
whatsoever, including but not limited to damage or loss of use of
equipment, plant or power system, cost of capital, loss of power,
additional expenses in the use of existing power facilities, or claims
against the purchaser or user by its customers resulting from the
use of the information, recommendations and descriptions contained herein.
Eaton
Electrical Sector
1000 Eaton Boulevard
Cleveland OH 44122
United States
877-ETN-CARE (877-386-2273
Eaton.com
© 2014 Eaton
All Rights Reserved
Printed in USA
Publication No. IM01005032E TBG01131
June 2014
Eaton is a registered trademark.
All other trademarks are property of their
respective owners.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising