AeGIS 7000 Series Quick Reference Guide

AeGIS 7000 Series Quick Reference Guide
AeGIS 7000 Series Quick Reference Guide
Step 1
Step 2
Step 3
∗
How to log into the programming mode
Press and hold the “0” and press the “#” and release both keys (The Welcome screen should stop scrolling, if
not repeat this step).
Enter the 4-digits valid Master Code.
Select the Function Code from the table below
Function Code Table
CODE
DESCRIPTION
CODE
DESCRIPTION
Edit Welcome Message
Exit the programming mode
10
#
00
01
02
03
04
05
06
07
(local programming) or clear the
existing program.
To accept program
Change Unit Master Code
Add a Tenant
Modify a Tenant
Delete a Tenant
Clear All Tenants
Manual Lock/Unlock Door
Change Directory Digits
Single/ Multi-Systems
08
System Number
00 (Master Code)
06 (Directory Digits)
70 (Talk Time)
71 (Open Interval)
0000
3 Digits
60 Seconds
12 Seconds
46
50
70
71
72
73
74
75
76
78
91
Parameter Default Settings Table
72 (Lock-Out Count)
73 (Unit Dialing)
74 (Auto Answer)
75 (Beep Enable)
Display System Information
Clear the EEPROM Memory
Change Talk Time
Change Door Open interval
Change Lock-out Count
Select Tone/Pulse Dialing
Enable/Disable Auto Answer
Enable/Disable Key-Press Beep
Enable/Disable Speaker Beep
when the System Open the
Gate/Door
View Directory by Name
Exit Programming Mode
(Remote Programming Via
Phone)
3 Tries
Tone Dialing
Enable (always answer)
76 (Beep when Door/Gate
Open by the System)
KEYPAD LAYOUT
OPERATION
1. To place a call from the Aegis 7000 Series: press
QZ−
− ABC DEF
number “3” (to view name from A-Z) or “6” (to view
2
3
1
name from Z-A) and press “#”.
2.
To place a direct call: press “#” wait for dial tone and
GHI JKL MNO
Refer to the
enter the tenant’s directory number.
4
5
6
Installation and
3. To grant access to visitor: the tenant must press
PRS TUV WXY
Program Manual for
“9”.
7
8
9
more detail
4. To use the personal Access Code: Press and hold
“0” and press “∗” and release both keys and enter the
0
#
∗
4-digits access code.
5. To extend a talk time: tenant must press “#” after
hearing the time out warning beep. Do not press the
“#” before you hear the warning beep.
6. To call into the AeGIS system: dial the AeGIS’s
phone number, you will hear one short beep if your
call is connected and press “∗” to talk to your visitor
and press “9” if you want to grant access to your
visitor. This feature does not work with multisystems on single phone line.
Remote Phone Programming
Single System in Single Telephone Line
Step 1
Log into the programming mode: Call into the Aegis 7000 Series, the Aegis will answer with either ONE
SHORT BEEP (door is in open position) or TWO SHORT BEEPS (door is in closed position).
Step 2
Press “#” and your valid Master Code. If your Master Code has been accepted, you will hear two short beeps
and you are in programming mode, if your Master Code has been rejected, you will be disconnected from the
system.
Step 3
Used the Function Codes above to perform the programming. Press “91” and “#” to disconnect the connection.
Multi-Systems in Single Telephone Line
Step 1
Log into the programming mode: Call into the Aegis 7000 Series, the Aegis will answer with either ONE
SHORT BEEP (door is in open position), TWO SHORT BEEPS (door is in closed position) or ONE LONG
BEEP (Combination of closed and open).
Step 2
Press the system ID number (1-8) and press “#” and enter your valid Master Code (two short beeps).
Step 3
Used the Function Codes above to perform the programming. Press “91” and “#" to disconnect the connection.
Pach & Company
AeGIS 7000 Series Quick Reference Guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising