DELIVER TO CONSUMER

DELIVER TO CONSUMER
INSTALLER-
DELIVER TO CONSUMER
FS5 OWNERS MANUAL
SPECIFICATIONS
CONSTRUCTION
Case: Outdoor grade reinforced fiberglass
Ventilation: 50 cu ft/min air volume
Acoustic rating: 50dB(A)
Weight: 13 lbs.
AIR F
ELECTRICAL
Voltage required: 120VAC 60Hz
Power consumption: 250 Watts max
Current usage: 2.0 amps
LOW
LAMPS
Type: Quartz-halogen; proprietary design
Lamp life: 700hrs average
1/2" FLEX CONDUIT
(NOT SUPPLIED)
FINISHED
SOIL
MAX.
HEIGHT
GRADE
LEVEL
MAX.
HEIGHT
2883 BAYVIEW DRIVE FREMONT, CA 94538
PM10082 12/96
WARRANTY
One year limited warranty, excluding lamp
LISTING
UL classification number 35Z1
UL file number E11725
WARNING: DO NOT INSTALL
WITHIN 1.5M (5 FT.) OF A POOL,
SPA ,OR HOT TUB.
ADVERTISSEMENT: NE PAS INSTALLER A MOINS DE 1,5 M D'UNE
PISCINE OU D'UNE CUVE DE RELAXATION.
TEL(800)327-7877 FAX(510)490-3247 www.fiberstars.com
IMPORTANT!
DO NOT BLOCK AIR VENTS
ON BOTTOM OF UNIT!
Final top soil/landscape height should
not be greater than the top of installation
base. The air vents for the illuminator
are toward the bottom of the unit. If the
illuminator is not properly vented, it will
overheat and turn the unit off. This will
cause premature lamp failure and could
cause the fiber optic cables to melt.
ILLUMINATOR
AIR
FLO
W
FAILURE DUE TO IMPROPER
VENTILATION IS NOT COVERED
UNDER OUR WARRANTY!
FINISHED
SOIL
MAX.
HEIGHT
GRADE
LEVEL
MAX.
HEIGHT
INSTALLATION
BASE
Limited Warranty Policy
Fiberstars, Inc. (“Fiberstars”), warrants the Lighting Systems (illuminator and fiber), excluding the lamp, to be free from defects in material and/or workmanship, under normal use and service,
for a period of ONE YEAR from the date of installation.
A Lighting System is defined as a Fiberstars Illuminator coupled with Fiberstars fiber to deliver fiber optic lighting. The use of a Fiberstars component (illuminator or fiber
tubing) with a non-Fiberstars component voids all warranties. Fiberstars components are designed to be part of a Fiberstars system. Their use with other components will affect
their performance and therefore will not be warranted.
In the event of a defect in material or workmanship during the warranty period, Fiberstars will repair or replace (at its option) the Lighting System under the conditions of the Warranty. Fiberstars
will do so at its expense for the materials but not for shipping. THIS REMEDY IS THE SOLE AND EXCLUSIVE REMEDY FOR ANY AND ALL CLAIMS RELATING TO ANY BREACH OF
WARRANTY BY FIBERSTARS.
LIMITATIONS, EXCLUSIONS AND OTHER RIGHTS:
A.
EXCEPT AS PROVIDED HEREIN, FIBERSTARS MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND ALL SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED. SOME STATES DO NOT ALLOW THE
EXCLUSION OF AN IMPLIED WARRANTY, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
B.
IN NO EVENT SHALL FIBERSTARS BE LIABLE FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF FIBERSTARS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE. THIS DISCLAIMER APPLIES DURING AND AFTER THE WARRANTY PERIOD. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
C.
Fiberstars is not responsible for defects or malfunctions in and/or damage to Lighting Systems where a sale is specifically made without warranty. In such sales the disclaimers of
warranty and liability, set forth above, shall continue to apply.
D.
This warranty covers normal consumer use and does not cover damage which occurs in shipment or failure with results from alteration, accident, theft, misuse, abuse, abnormal
use, negligent installation, improper maintenance or where adequate care has not been taken to prevent damage to the Lighting System.
E.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
If you discover a defect or malfunction during the period to which the Warranty applies, write or phone Fiberstars for information on receiving warranty service.
TROUBLE SHOOTING
-THERE IS NO LIGHT
You can hear the fan running: The lamp has probably failed. Replace with Fiberstars part #HI-111.
There is no fan running: The illuminator is not getting power. Check the GFCI breaker, check the fuse on the illuminator.
-THE UNIT SHUTS OFF AFTER A FEW MINUTES THEN COMES BACK ON
Check to see if the ventilation holes are blocked
Turn off the power. Remove the four screws securing the lid and check for an obstruction in the cooling fan.
-REMOTE CONTROL UNITS (FS5C-R)
There is a rapid clicking sound at the illuminator when the button is pressed: The receiver module in the unit is defective. Have
a qualified service company replace it.
There is a click at the unit when the button is pressed, but no light: If you hear the fan running, the lamp has probably failed.
Replace with Fiberstars part #HI-111. If you cannot hear the fan running, the receiver module is probably defective. Have a qualified
service company replace it.
There is NO click at the unit when the button is pressed: Make sure that the plug-in transmitter is plugged in to functioning
outlet. The red light on the transmitter should glow when a button is depressed. Make sure that the small switch marked "1-4 / 5-8" is
in the "1-4" position (fig. 2-1). If the transmitter is functioning properly, but the illuminator still does not come on, the receiver module
may be defective. Have a qualified service company replace it.
-LIGHTS ARE NOT BRIGHT ENOUGH
The adequacy of pool lighting is subjective at best. What is acceptable to most, may not be for some. The pool builder is given
guidelines by Fiberstars, and the builder alone is responsible for the final design and installation. There are many factors that determine the ultimate brightness of our product; fiber lengths, pool finish color, installation techniques, etc. Remember that darker colors on
our color wheel, i.e. magenta, are not as bright as lighter colors like white.
CHANGING THE LAMP
Remove the four screws
securing the lid.
USE ONLY FIBERSTARS
PART #HI-111
MAKE SURE THE ILLUMINATOR IS COOL! Use your
finger to slide out the socket/
lamp assembly.
FIG 1-1
CHECKING THE FUSE
FS5C-R CONTROLLER
Indicator Light
Letter Code Dial
1-4 / 5-8 Selector Switch
FIG 2-1
Pull the lamp free from the
socket. Install the new lamp by
pushing the pins into the
socket. DO NOT TOUCH THE
FILAMENT OR THE LAMP
WILL BURN OUT PREMATURELY.
Numbered buttons
The fuse is located above the
connection box on the side of the
illuminator. Push the fuse holder
cap and twist it to remove the
cap and fuse. The fuse filament
should be intact, and not be broken or burnt. If the fuse is defective, replace with a standard
230V 2.5 Amp fuse. Push the
fuse/cap assembly back in to the
holder and twist to lock.
FIG 1-2
Slide the new lamp with the socket
back into the bracket. The lamp
should sit FLAT on the bracket for
maximum light transmission.
FS5 ILLUMINATOR MODELS
FS5
POWER
ON/OFF
FUSE
FS5
WHITE LIGHT ONLY
(TOGGLE SWITCH CONTROL)
FS5C-J
FS5C-J
COLOR WHEEL
(AUTOMATIC CONTROL
COMPATIBLE)
FUSE
FS5C
POWER
ON/OFF
COLOR
WHEEL
FUSE
FS5C
COLOR WHEEL
(TOGGLE SWITCH CONTROL)
FS5C-M POWER
ON/OFF
COLOR
WHEEL
FUSE
FS5C-M
COLOR WHEEL
(MASTER CONTROL ILLUMINATOR
FOR SYNCHRONIZED SYSTEMS)
FS5C-R
FUSE
FS5C-R
COLOR WHEEL
(PLUG-IN REMOTE CONTROL)
FS5C-S POWER
ON/OFF
FUSE
FS5C-S
COLOR WHEEL
(SLAVE ILLUMINATOR - COLOR
WHEEL CONTROL BY MASTER)
NOTE: YOUR POOL BUILDER HAS MANY OPTIONS WHEN SUPPLYING POWER TO THE ILLUMINATOR. HAVE THE BUILDER PROVIDE INSTRUCTION FOR YOUR ILLUMINATOR CONTROL.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising