2-1384 SHR manual - Kirkland Fireplace

2-1384 SHR manual - Kirkland Fireplace
™
For Models:
SHR36
SHR42A
SHR48
SHR52
SHR Series
Woodburning Fireplace
Homeowner's Installation & Operating Manual
Underwriter's Laboratories Report No. MH6018
CFM Specialty Home Products
410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777
www.majesticproducts.com • www.vermontcastings.com
DO NOT DISCARD THIS MANUAL: Retain for future use.
20001384 7/04 Rev. 13
SHR Series Woodburning Fireplace
Safety Information
PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING FIREPLACE.
IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to
follow these instructions may result in a possible fire hazard and will void the warranty.
Description
The SHR Series fireplaces are solid fuel, woodburning
fireplaces. The SHR36/42A/48 (Super Hearth) are
clean-face fireplaces.
Precautions
CFM Specialty Home Products fireplaces and component parts have been highly tested and will operate
safely when installed in accordance with instructions
provided in this manual. Carefully read and understand
all instructions before beginning installation.
If you notice any damage to fireplace or component
parts, immediately report damage to your Majestic
Fireplaces dealer.
Only use CFM Specialty Home Products components
or the warranty will be voided and a fire hazard may be
created.
CFM Specialty Home Products warranty will be voided
by and CFM Specialty Home Products disclaims any
responsibility for the following actions:
• Installation of any damaged fireplace or
chimney component;
• Modification of fireplace, chimney assembly
or any component parts thereof; (except for
chase flashings as detailed in the Chimney
Top installation instructions).
• Installation other than as instructed by CFM
Specialty Home Products; or
• Installation and/or use of any component part
not manufactured or approved by CFM Specialty Home Products in combination or
assembly with a Majestic Fireplaces fireplace
system, notwithstanding any independent
testing laboratory or other third party approval of such component parts or accessory.
Any such action may possibly cause a fire hazard.
Consult local building codes to ensure that you are in
compliance before installing the fireplace.
Fireplaces must be vented to the out-of-doors.
Do not obstruct or modify air inlets/outlets in any
manner.
2
Do not install combustible materials on any of the
black fireplace surround.
Burn only solid wood fuel or gas logs.
Do not install a solid fuel burning insert or other
products not specified for use with this fireplace.
These fireplaces are not approved for installation in
mobile homes.
Proposition 65 Warning: Fuels used in gas,
woodburning or oil fired appliances, and the products of combustion of such fuels, contain chemicals
known to the State of California to cause cancer,
birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6
Drafts
The fireplace should not be located in areas that create
drafts (ie: frequently opened doors and central heating
air inlets/outlets) that hamper the normal flow of air into
the fire.
Gas Logs
If you plan to install a gas log, the gas line should be
installed before framing the fireplace. The gas line must
be installed by a certified gas line installer.
SHR36 / SHR42A / SHR48 / SHR52
Listed
UL 127
Standard for Factory Built Fireplaces
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . 2
Specifications and Framing . . . . . . . . . . . 3
Parts Identification . . . . . . . . . . . . . . . . . . 5
Chimney Requirements . . . . . . . . . . . . . . 6
Planning Information . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . 8
Replacement Parts . . . . . . . . . . . . . . . . 20
Accessories . . . . . . . . . . . . . . . . . . . . . . 21
20001384
SHR Series Woodburning Fireplaces
SHR36 Series Woodburning Fireplace
Rough
Opening
Depth
³⁄₄"
13³⁄₈" Dia.
(340mm)
11" Dia.
( 279mm)
(1 41
05 ⁹⁄₁
6m ₆"
m
)
³⁄₄"
Rough Opening Width 47³⁄₄"
(1213mm)
80
20
⁷ ⁄₈
"(
19
m
m
)
m
m
)
Rough
Opening
Height
81
³ ⁄₄
"(
57¹⁵⁄₁₆" (1472mm)
29" (737mm)
10³⁄₈"
(2264mm)
26³⁄₄"
(680mm)
57¹⁵⁄₁₆" (1472mm)
³⁄₄"
³⁄₄" (19mm)
12¹⁄₂"
(318mm)
48¹⁄₄"
(1226mm)
15⁵⁄₈"
(397mm)
Outside
Air
44"
(1118mm)
36"
(914mm)
13³⁄₄"
(349mm) 7³⁄₄"
(197mm)
24"
(610mm)
Gas Line
Access
7⁷⁄₁₆"
(189mm)
14¹⁄₂"
(368mm)
Gas Line Access
46¹⁄₄" (1175mm)
FP526A
Fig. 1 SHR36 Series specifications and framing.
SHR42A Series Woodburning Fireplace
Rough
Opening
Depth
65¹⁄₈" (1654mm)
13³⁄₈" Dia.
(340mm)
11" Dia.
(279mm)
Rough Opening Width 53³⁄₄"
(1365mm)
m
)
(1 46
17 ¹⁄₈
2m "
m
)
³⁄₄"
m
Rough
Opening
Height
³⁄₄
"(
92 19m
¹¹⁄
₈" m)
(2
34
0
65¹⁄₈" (1654mm)
32¹⁄₂" (826mm)
10¹⁄₂"
(267mm)
29¹⁄₄"
(743mm)
³⁄₄"
³⁄₄"
³⁄₄" (19mm)
12¹⁄₄"
(311mm)
54¹⁄₄"
(1378mm)
19¹⁄₄"
(489mm)
Outside
Air
48¹⁄₈"
(1222mm)
42" (1067mm)
14¹⁄₄"
(362mm) 9"
(229mm)
10⁵⁄₃₂"
(258mm)
28¹⁄₂"
(724mm)
Gas Line
Access
7⁷⁄₁₆"
(189mm)
Gas Line Access
52¹⁄₄" (1327mm)
FP546A
Fig. 2 SHR42A Series specifications and framing.
20001384
3
SHR Series Woodburning Fireplace
SHR48 Series Woodburning Fireplace
Rough
Opening
Depth
66³⁄₈" (1686mm)
13³⁄₈" Dia.
(340mm)
10³⁄₈"
(264mm)
11" Dia.
(279mm)
³⁄₄"
(1 47
20 ⁹⁄₁
³⁄₄
8m ₆ "
"(
19
m
93 m
)
⁷⁄₈ m
"( )
23
84
m
m
)
Rough Opening Width 59³⁄₄"
(1518mm)
Outside
Air
15⁵⁄₈"
(397mm)
13³⁄₄"
(349mm) 7³⁄₄"
(197mm)
53" (1346mm)
Rough
Opening
Height
48¹⁄₂" (1232mm)
66³⁄₈" (1686mm)
41" (1041mm)
26³⁄₄"
(680mm)
³⁄₄"
³⁄₄"
³⁄₄" (19mm)
12¹⁄₂"
(318mm)
48"
(1219mm)
28¹⁄₂"
(724mm)
Gas Line
Access
7⁷⁄₁₆"
(189mm)
14¹⁄₂"
(368mm)
Gas Line Access
58¹⁄₄" (1480mm)
FP545A
Fig. 3 SHR48 Series specifications and framing.
SHR52 Series Woodburning Fireplace
³⁄₄" (19mm)
Rough
Opening
Depth
31¹⁄₄"
(794mm)
Rough Opening Width 63⁷⁄₈"
(1622mm)
Rough
Opening
Height
m
)
7m
m
66
m
5"
(2
19
11" Dia.
(279mm)
Standoff
Notch
12" (305mm)
10
³⁄₄
"(
³⁄₄"
)
(1 52
33 ¹⁄₂
4m "
m
)
³⁄₄"
74¹⁄₄" (1886mm)
13³⁄₈" Dia.
(340mm)
8¹⁄₂"
(216mm)
74¹⁄₄" (1886mm)
³⁄₄"
41" (1041mm)
23"
(584mm)
Outside
Air
13¹⁄₂"
(343mm) 9¹⁄₄"
(235mm)
12¹⁄₂"
(318mm)
52¹⁄₂" (1334mm)
68⁷⁄₈"
(1749mm)
52"
(1321mm)
33"
(838mm)
Gas Line
Access
7⁷⁄₁₆"
(189mm)
Gas Line Access
62³⁄₈" (1584mm)
Fig. 4 SHR52 Series specifications and framing.
4
20001384
SHR Series Woodburning Fireplaces
Chase Installation
Insulation methods shown are optional for
cold climate, not a requirement for unit
operation.
Termination Cap
Storm Collar
Pan Flashing
Batt Insulation
(cut out around
firestop)
Draftstop
Firestop
Ceiling Level
Ledge Bracket
Surround
Damper Control
Gas Line Access
(both sides)
Gas Line Knockout
(both sides)
Screen
Grate
Outside Air
Cover Plate
Firebox
Metal Safety
Strips (1,2 or 3)
FP554A
Fig. 5 Fireplace and chase parts identification. (SHR48 shown)
20001384
5
SHR Series Woodburning Fireplace
Chimney Requirements - Offset Installations
Offset
Chimney Flue Exit
Rise
Chimney
Section
FP282
B
A
30˚ Elbow Offsets
30°
Return
Elbow
G
G
D
E
6 FT.
30°
Offset
Elbow
Rise
C
30°
Return
Elbow
H
Offset
11CS
Support
H
30°
Offset
Elbow
B
Hearth Floor
Example 1
Example 2
Notes: G + H cannot exceed 20 feet.
*11CF Chimney airspace clearance = 2" minimum.
Illustration Key
The following safety rules apply to offset
installations (letters correspond with illustration above):
A. Height of the chimney is measured from
the hearth to the chimney exit.
SHR36 SHR42A SHR48 SHR52
90'
90'
90'
90'
Max.:
Min.:
0 Elbows 14'6"
2 Elbows* 15'6"
4 Elbows* 21'0"
14'6"
15'6"
21'0"
16'0"
19'0"
24'0"
16'0"
19'0"
24'0"
B. Do not use more than 4 elbows per
chimney.
Attach the straps of the return (top) elbow to a
structural framing member.
The offset (first) elbow of any pair does not
have straps.
Example 3
FP269
C. The chimney cannot be more than
30˚ from the vertical plane in any
installation.
D. The maximum length of the angled
run of the total chimney system is 20
feet. (G plus H cannot exceed 20 feet.)
E. A chimney support (Model 11CS) is
required every 6 feet of angled run of
chimney. Chimney supports are
required for every 30 feet and 60 feet
chimney height above the hearth.
Determine the offset distance of your
chimney arrangement from the centerline of the fireplace to the centerline of
the chimney where it is to pass through
the first ceiling.
NOTE: This offset distance may not be
your full offset distance. See Examples
2 and 3.
1' 1¹⁄₂' 3' 4'
Chimney
Support
Elbow
0
1
0
2
1
0
2
0
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
0
0
0
0
1
0
0
1
0
0
2
0
1
2
0
1
3
0
2
3
1
2
0
1
3
0
2
3
1
2
0
1
3
0
2
3
1
2
0
0
0
0
0
0
0
0
1
0
1
1
0
1
1
0
2
1
0
2
1
0
2
1
3
2
1
3
2
1
3
2
4
3
2
4
3
2
4
3
5
Offset
Rise
3"
8¹⁄₄"
11¹⁄₄"
13¹⁄₂"
16¹⁄₂"
20¹⁄₄"
21³⁄₄"
26¹⁄₄"
28¹⁄₂"
31¹⁄₂"
34¹⁄₂"
37¹⁄₂"
41¹⁄₂"
45"
47¹⁄₄"
51"
53¹⁄₄"
56¹⁄₄"
59¹⁄₄"
62¹⁄₄"
64¹⁄₂"
68¹⁄₄"
70¹⁄₂"
74¹⁄₄"
78"
81"
84"
87"
89¹⁄₄"
93"
95¹⁄₄"
99¹⁄₄"
101¹⁄₄"
104¹⁄₄"
107¹⁄₄"
110¹⁄₄"
114"
117³⁄₄"
120"
123³⁄₄"
11"
20"
25¹⁄₄"
29¹⁄₄"
34¹⁄₄"
40³⁄₄"
43¹⁄₂"
51¹⁄₄"
55¹⁄₄"
60¹⁄₄”
65¹⁄₂"
70³⁄₄"
77³⁄₄"
83³⁄₄"
87¹⁄₂"
94"
98"
103¹⁄₄"
108¹⁄₂"
113¹⁄₂"
117¹⁄₂"
124"
128"
134¹⁄₂"
140³⁄₄"
146"
151¹⁄₄"
156¹⁄₂"
160¹⁄₄"
166³⁄₄"
170³⁄₄"
177³⁄₄"
181³⁄₄"
186¹⁄₄"
191¹⁄₂"
196³⁄₄"
203¹⁄₄"
209³⁄₄"
213¹⁄₂"
220"
Fig. 6 Chimney system requirements.
6
20001384
SHR Series Woodburning Fireplaces
Planning Information
Preplanning an installation is very important to ensure
safety and to save time and money. An installer must
predetermine where a fireplace will be set and how the
chimney system will be run.
Mounting the Fireplace
A fireplace may only be mounted on the following
surfaces:
1. A flat combustible surface.
2. A raised wooden platform.
3. A concrete block or other solid object placed beneath
each of the four (4) corners of the fireplace.
The fireplace must be spaced 3/4 inch from a combustible back wall and 3/4 inch from a combustible side
wall or support. (Fig. 20, Page 14)
Planning the Chimney Run
Determine how the chimney will be run, length of run
and chimney components required to complete the job.
(Fig. 6) Never install a chimney below minimum
heights.
LT
L1
L1
11CF
Chimney
Model No.
Total
Length
(LT)
11CF1
11CF18
11CF3
11CF4
11¹⁄₂"
17¹⁄₂"
35¹⁄₂"
47¹⁄₂"
Installed
Length
(L1)
10¹⁄₂"
16¹⁄₂"
34¹⁄₂"
46¹⁄₂"
The Ten Foot Rule
Major U.S. building codes specify a minimum chimney
height above the roof top. The “Ten Foot Rule” is a fire
safety rule and not a draft rule. To ensure proper draft,
it is recommended that you always meet or exceed the
“Ten Foot Rule,” especially when installing a termination
on a high pitch roof. (Fig. 8)
The key points of the "Ten Foot Rule" are:
1. If the horizontal distance from the chimney to the
peak of the roof is 10' (3m) or less, the top of the
chimney must be at least 2' (610mm) above the peak
of the roof, but never less than 3' (914mm) in height
above the highest point where it passes through the
roof.
2. If a horizontal distance from the chimney to the peak
of the roof is more than 10' (3m), a chimney height
reference point is established that is on the surface
of the roof a distance of 10' (3m) from the chimney in
a horizontal plane. The top of the chimney must be at
least 2' (610mm) above the reference point, but
never less than 3' (914mm) in height above the
highest point where it passes through the roof.
0 To 10’
2’ Min.
3’
Min.
0 To 10’
2’ Min.
3’
Min.
Reference
Point
FP288b
AC246
Fig. 7 Installed lengths of chimney sections.
Fig. 8 Ten Foot Rule illustration.
In planning a chimney system, it is important to know:
1. The height of a chimney is measured from the hearth
to the exit point on the termination.
2. A chimney cannot be offset more than 30 degrees
from a vertical plane.
3. A chimney may run straight up or it may be necessary to offset it to avoid obstructions.
4. The maximum length of an angled run (total chimney
system) is 20 feet.
5. No more than 2 offsets (4 total 30˚ elbows in) per
fireplace may be used.
6. A guy wire stabilizer is required for chimneys extending more than 6 feet above a roof line.
20001384
7
SHR Series Woodburning Fireplace
Installation
Chimney Supports
The chimney system is supported by the fireplace for
vertical chimney heights less than 30 feet above the
hearth. Chimney supports are required if the vertical
height exceeds 30 feet with 11CF chimneys. Locate
chimney supports at ceiling holes or other structural
framing at 30 foot heights. Spacing between chimney
supports must not exceed 30 feet. Use Chimney
Support Model 11CS. (NOTE: The 11CS can not be
mounted directly to the fireplace.) Support provided
by elbow straps fulfills the support requirement only if
they are spaced as previously described. (A chimney
support is 2¹⁄₂" long when installed.)
Angled chimney runs require a support every six (6)
feet in addition to the elbow straps. Chimney supports
are used for this function. (Fig. 9)
Chase Installation
A chase is a vertical boxlike structure which encloses
the fireplace and/or chimney. Chases are typically built
on the outside of the house with fireplace opening cut
into the outer wall of a room. (Page 5, Fig. 5)
If you need help in determining fireplace location or how
the chimney system should be run, contact your
Majestic Fireplaces dealer for assistance.
Insulating Fireplace
Enclosure for Cold Climates
If you live in a cold climate, it is not required but
highly recommended that you insulate the fireplace
enclosure to eliminate cold air penetration as much
as possible.
Insulate base of fireplace with a noncombustible
insulation rated for a minimum of 300° F. Insulating
is very important for outside wall installations over
a concrete slab. If fireplace is installed on a platform,
insulation should be placed on top of the platform
before fireplace is set. (Fig. 10)
When a fireplace is installed in a chase or on an
outside wall, enclosure should be treated like any
outside wall in a home. Insulation should be installed
on the inside wall as well as the outside wall(s). In a
chase, it is also a good idea to install a firestop at
the first ceiling level above the fireplace and enclose
the chase with sheeting material. Insulation may
then be installed above sheeting material to assure
the space around the fireplace is totally protected.
(Fig. 5)
CAUTION: WHEN INSTALLING A FIREPLACE IN
AN INSULATED ENCLOSURE, BE SURE ALL
REQUIRED AIR SPACES ARE MAINTAINED.
(Page 15, Fig. 19)
Chimney
Support Strap
11CS
FP284
Fig. 9 Chimney support installation
8
20001384
SHR Series Woodburning Fireplaces
Rear Firebrick
Brick
Retainer
Hard, Flat
Surface
Side Firebrick
Front
Notch
FP1234
Fig. 11 SHR52 Firebrick installation.
Insulation
3. Slide the rear firebrick back into the left corner
behind the end of the left firebrick. Push both panels
back as far as possible into the left side and corner.
4. Swing the right side of the back firebrick into place.
Attach the left brick in place using a brick retainer at the
top and phillips screw removed earlier.
Platform
FP555SHR
Fig. 10 Insulating between platform and fireplace.
Framing
Framing can be constructed before or after the fireplace
is set in place, however, most installers build the frame
before setting the fireplace.
Frame fireplace with 2 x 4 lumber or heavier materials.
Refer to framing dimensions in Figures 1 - 4 for basic
fireplace specifications.
NOTE: Framing should be positioned to accommodate
wall covering and fireplace facing material.
5. Slide the right firebrick into place as far back as
possible. Attach rear firebrick and right firebrick using
brick retainers and phillips screws removed earlier.
6. Slide the hearth firebrick into the grate clip. (Fig. 12)
The grate will be used as a handle to set the hearth
firebrick in place.
7. With the hearth firebrick securely in place in the
grate clip, carefully lift the hearth firebrick into the
fireplace, set the rear of the firebrick down, then slide
back to meet the rear firebrick. Gently set the front of
the firebrick in place. Replace screens and screen rod
smoke baffle assembly.
Grate
Firebrick Installation
For the SHR52 model the firebrick is packed separately
and must be installed in the fireplace.
Hearth
Firebrick
You will need four (4) firebrick, three (3) brick retainers,
a phillips head screwdriver, and the grate.
The side and rear firebrick each have a notch in the top
of the brick panel. The side firebrick have a notch in the
lower front side of each panel. The herringbone pattern
faces out of the fireplace always. (Fig. 11)
NOTE: The screens and screen rod smoke baffle
assembly must be removed and set aside before
proceeding. Remove the two screws holding the
screens place. There are seven screws holding the
screen rod smoke baffle in place.
1. Remove the three brick retainers from the combustion dome by removing the phillips screws, set aside.
2. Set the left firebrick in place on the left side of the
fireplace.
20001384
Grate Clip
FP1235
Fig. 12 Hearth firebrick in place in grate clip.
Chimney Set-up
Since you have already preplanned the chimney run,
you should know exactly how the installation is to be
accomplished — how much pipe is required, the
number of elbows, if any, and type of termination to be
used.
9
SHR Series Woodburning Fireplace
CAUTION: REPORT TO YOUR DEALER ANY PARTS
DAMAGED IN SHIPMENT, SPECIFICALLY CHECK
THE END CONNECTION OF CHIMNEY SECTIONS
AND ELBOWS.
Chimney Centerline
Actual Centerpoint
11¹⁄₈"
NOTE: SHR Series Fireplaces must use CFM Corporation model 11CF, 11 inch, 2 wall chimney systems. The
installation procedure described in this manual applies
only to the 11CF system, chimney components may
not be mixed.
Straight-Up Chimney Installation
To mark the centerline of the flue, put the fireplace in
final position and measure out from the wall 11¹⁄₈". Mark
a spot on the ceiling directly above the fireplace. Draw
a line parallel to the back wall through this mark. (Fig.
13)
Plumb Line
Plumb Bob
Imaginary
Centerpoint
Using a plumb bob positioned directly over center point
of fireplace flue collar, mark the ceiling to establish the
chimney center point. (Fig. 13)
Offset Installation
In order to clear an obstruction, it may be necessary to
offset chimney from vertical. This is accomplished by
using CFM Corporation elbows. Use the 30˚ Offset
Elbow table on Page 6 to determine proper offset and
parts required.
Each offset requires two (2) elbows. The second elbow
is equipped with support straps. It is very important to
install the second elbow in each offset as close to the
ceiling or support as possible so the elbow straps can
be secured to framing members to help support the
weight of the chimney.
Determine offset distance of your chimney arrangement
from centerline of fireplace to centerline of chimney
where it is to pass through ceiling.
Locate center point of the chimney on ceiling as though
a straight up chimney arrangement is to be used.
Measure your offset dimension from straight up chimney center point on ceiling.
Ceiling Chimney Hole/
Possible Obstructions
The size of the hole in ceiling will vary with the angle at
which the chimney passes through ceiling.
Drive a nail up through ceiling at marked chimney
center point. Go to floor above and see where hole will
be cut. Check to see where existing ceiling joists and
other possible obstructions are located...i.e. wiring,
plumbing etc... If necessary, reposition chimney and/or
fireplace to avoid obstructions.
10
FP556SHR
Fig. 13 Locate centerline of chimney with plumb line.
Cutting the Hole
Cover fireplace collar opening and cut proper sized
chimney hole in chimney. (Fig. 14 & 15)
Framing the Ceiling Hole
Frame the ceiling chimney hole as shown in Figure 15.
It is good practice to use framing lumber that is the
same size as the ceiling joists; this is a requirement at
attic level.
The following table gives firestop spacer model numbers:
CHIMNEY HOLE SIZE
Size of Chimney
11" CF 2-Wall
FP548SHR
Angle of Chimney at Ceiling
30˚
Vertical
FS2A
FS6A
17¹⁄₂" x 17¹⁄₂"
17⁷⁄₈" x 29⁵⁄₈"
Fig. 14 Ceiling chimney hole size necessary for installing
firestop spacer.
20001384
SHR Series Woodburning Fireplaces
The inside dimension of the frame must be the same
as the hole size selected from Figure 11 in order to
provide the required 2 inches of air space between the
outside diameter of the chimney and the edges of the
framed ceiling hole.
Existing
Ceiling
Joists
17¹⁄₂"
Metal Safety Strips
(1, 2 or 3 pieces)
17¹⁄₂"
Fireplace
Chimney
Hole
1¹⁄₂"
1/2" Min.
Overlap
Platform
"Z" Safety
Strip
(not supplied)
Hearth Ext.
FP557a
Fig. 16 Safety strip installation.
New Framing
Members
FP551b
Fig. 15 Typical frame for ceiling chimney hole
Positioning, Safety Strips,
Securing the Fireplace
Nail Sidenailing
Flanges
Slide fireplace into position.
Lift the fireplace front slightly and slide the metal safety
strips under front bottom edge about 1¹⁄₂ inches,
allowing the remainder to extend in front of firebox.
Overlap strips at least 1/2 inch to provide a positive
joint. (Flat safety strips are packed with fireplace.) (Fig.
16)
Safety strips are used to ensure that any combustible
materials in front of the fireplace are protected even
though a noncombustible hearth extension is required.
If fireplace is to be elevated above the floor, a “Z”
shaped metal safety strip must be fabricated and used
to protect combustible surfaces in front of the fireplace.
This “Z” shaped safety strip is not provided but must be
fabricated of metal with each horizontal leg at least 1¹⁄₂
inches wide and equal in length to the metal strips
provided with the fireplace.
FP549
Fig. 17 Fasten fireplace in position.
Installing Outside Air Kit
An outside air damper assembly is installed in all SHR
Series Fireplaces. If desired, or if local codes mandate
the use of an air kit, then an AK-MST is required to
complete the installation (from air damper assembly to
the outdoors). If the outside air kit is to be used, the AKMST MUST be installed BEFORE the fireplace is
enclosed. Refer to the AK-MST instructions for field
installation.
Note: Safety strips are not required over noncombustible floors where all supports at the base of the fireplace are noncombustible.
Four (4) nailing flanges are supplied with the fireplace
(found on the fireplace hearth). To level the box and
secure it firmly in place, remove the nailing flanges from
the hearth and install at the sides of the fireplace as
shown in Figure 17.
20001384
11
SHR Series Woodburning Fireplace
Installing the Chimney System
Pipe Section
Start by attaching the first chimney section to the
collar on top of the fireplace.
UP
Install the pipe as pictured in Figure 18. When you
get a good lock, you will hear the pipe clearly snap
together. Once sections are snap-locked in place, it is
extremely difficult to get them apart. Make sure the
pipe is firmly snapped and locked together as
each pipe section is mounted.
Pipe
Rim
Hem
Lance
Pipe
Rim
When installing elbows, only outer pipe will snap- lock.
Middle pipes simply slide into position. Be sure to
always attach straps on upper elbow to a structural
framing member. (Fig. 19)
Continue installing the pipe as required until pipe is
installed up through the ceiling. At this point, you must
install a firestop spacer.
FP558SHR
Fig. 18 Install pipe, listening for the snap-lock to fasten.
Installing the Firestop Spacer
in the Ceiling Hole
Support Structure
A firestop spacer is used to keep pipe spaced properly
and required for safety.
Nail the firestop spacer (at each corner) to the framing
members of the ceiling hole. Note: A firestop spacer
is not required at the roof.
Elbow Strap
(must be tight)
Hole sizes listed in Figure 14 for angled firestop
spacers provide minimum required air space to
chimney pipe for ceiling thickness up to eight (8)
inches. When combined thickness of ceiling material,
ceiling joists and flooring material exceeds eight (8)
inches, adjustments must be made in framing to
assure that minimum air spaces to chimney are
maintained.
Angle Firestop
ANGLED STRAP
Proper Firestop Spacer Installation
FP270/271
Figure 20 shows different installation procedures for
both an area that is an attic and an area that is not an
attic.
If the area above the
ceiling is not an attic,
position the firestop
spacer with the flange on
the ceiling side and the
angled portion extending
up into the hole.
If the area above the
ceiling is an attic, position
the firestop spacer with
the flange on the top of
the framed hole and the
angled portion extending
down into the hole.
Ceiling
Hole
Framing
ELBOW STRAP
Chimney Support
Strap
(must be tight)
Fig. 19 Attach straps to a structural framing member.
Ceiling Installation
Attic Installation
Nails (4)
Joist
Firestop Spacer
Firestop
Spacer
Joist
Flange Down Into Hole
Nails (4)
Flange Up Into Hole
FP285
Fig. 20 Installing firestop spacer.
12
20001384
SHR Series Woodburning Fireplaces
Firestop spacers are not available for, nor are they
required on, vertical walls.
The chimney components (CF11) used on the SHR
series fireplaces have been tested and approved with
the area where the outer pipe slides through the
firestop spacer sealed with a noncombustible caulk if
desired, or left completely open with no sealant. This
sealing only applies to the SHR series fireplace.
Continue Installing Pipe to Complete Run
Continue attaching pipe sections to complete system to
next level always being careful that the pipe is firmly
snap locked in place before proceeding to next pipe
section.
Chimney Supports
If chimney supports are required, they are installed the
same as elbows. Nail chimney support straps to
adjacent structural framing, as shown in Figure 8, Page
8. Bend straps as necessary and make sure they are
secure so they will support the weight of the chimney. A
chimney support is 2¹⁄₂" long when installed. Consider
this dimension when determining how many straight
chimney sections are needed.
Note: Chimney supports are generally used in long
runs in a chase installation.
Additional Ceilings
If you encounter additional ceilings, repeat same steps
required for first ceiling installation. Refer to firestop
illustration on Page 12, Figure 20.
Penetrating the Roof
Cut and Frame Roof Hole
Size of roof hole varies with the type of chimney
termination installed. Refer to installation instructions
provided with the chimney termination to find correct
size roof hole.
There must be a 2" (52mm) air space between outermost portion of chimney sections and any adjacent
combustible surfaces. (Combustible surfaces include
burnable materials such as: ceiling members, joists,
flooring, combustible insulation and roof structures.)
WARNING: DO NOT PACK REQUIRED AIR SPACES
WITH INSULATION OR OTHER MATERIALS.
Mark an outline of the roof hole around the centerpoint
of the nail. NOTE: Hole dimensions given in the chimney top installation instructions are horizontal dimensions; therefore, the hole size must be marked on the
roof accordingly.
Cover the opening of the installed chimney so debris
cannot get into the system.
Cut and frame the hole. It is good practice to use
framing lumber that is the same size as the rafters.
Install the frame securely because the chimney top and
flashing anchored to the frame must be able to withstand heavy winds.
Install Remainder of Chimney Sections
Since you have already preplanned the height of your
termination according to the Ten Foot Rule, continue to
install pipe to the predetermined height.
Check the chimney top installation instructions for
details on how high above the roof top the chimney
sections (all pipes) should extend.
Run pipe to roofline. Since chimney system must be
vented to the out-of-doors, you must use an approved
termination.
If a chase is used, refer to the installation manual
provided with the termination cap.
Locate Chimney Centerpoint on Roof
Use same procedure detailed in locating center point of
the flue system.
Drive a nail up through roof at the center point. This will
determine center point on outside of the roof.
20001384
13
SHR Series Woodburning Fireplace
Installing Top Housing or Termination
Air Space Clearances
Combustible framing material MUST NOT
penetrate AIR SPACE (shaded areas)
Follow the installation instructions provided with the
chimney termination you have selected.
Installing Chimney in a Chase
Refer to Page 5, Figure 4 for an illustration of a typical
chase installation.
CAUTION: Treatment of firestop spacers and construction of chase may vary with type of building. These
instructions are not a substitute for local building codes.
You must check your local building codes to determine
specific requirements for your city or state. NOTE:
Other building materials may be required in addition to
Firestop Spacers.
2"
Standoff
³⁄₄" Air Space
to Sides
Front View
Finishing
CAUTION: All joints between the finished wall and the
fireplace surround (top/sides) must be sealed with
noncombustible material to prevent cold air leakage into
the room. Only noncombustible material may be applied
to the facing of the fireplace surround. (Black painted
area) (Fig. 21)
Side View
Firestop
³⁄₄" Air Space
to Back
Wall
Shield
The SHR52 has a framing shield between the front
standoffs that may be used to attach finish material.
(Fig. 23)
³⁄₄" Air Space
to Sides
Finish Wall
Finish the wall with material of your choice. Do not
install a combustible mantel shelf less than 12"
(305mm) from the top of the fireplace opening. Do
not install a mantel face plate less than 6" (159mm)
from top of fireplace opening. (Fig. 27) If a combustible material is used below a flat mantel shelf, consult
your local building codes for minimum clearance from
top of fireplace opening to bottom of mantel shelf.
0" Clearance to Floor
Only noncombustible material
may be applied as facing to
the black fireplace surround.
Hearth Extension
FP559SHR
Fig. 21 Minimum clearances to combustibles.
All joints (top, bottom and sides) where wall or decorative facing material meets fireplace surround must be
completely sealed with a noncombustible material.
(Figs. 22 - 27)
NOTE: No side wall protection is required for fireplaces
installed at 45° to two (2) side walls (corner installation).
14
20001384
SHR Series Woodburning Fireplaces
Mantel Clearance No Noncombustible Facing Material
12"
(305mm)
Max.
Combustible Mantel
and Trim
1¹⁄₂"
Combustible
Mantel and Trim
Finished Wall
Finished Wall
Header
1¹⁄₂"
Ledge Bracket
Ledge Bracket
12"
(305mm)
min.
Noncombustible
Material
*
12"
(305mm)
Max.
Header
12"
(305mm)
min.
* Minimum width from
top of surround to bottom
of screen rail
Mantel Clearance with Noncombustibel Facing Material
Surround
Face
Noncombustible
Material
6"
(159mm)
Min.
Surround
Face
Noncombustible Facing
Material
Fireplace Opening
Fireplace Opening
Must be sealed with
noncombustible material
Finished Wall
Ledge Bracket
1"
2 x 4 Stud
Finished Wall
Must be sealed with
noncombustible
material
FP531
Fig. 22 Mantel clearance.
Finished Wall
Finished Wall
Stud
Noncombustible
Decorative
Facing
2 x 4 Header
Framing Shield
Must be
sealed with
noncombustible
material
Must be Sealed with
Noncombustible
Material
Ledge Bracket
Surround
FP1166
Fig. 24 Fireplace surround flush with finished wall.
FP1277
Fig. 23 SHR52 framing shield may be used to attach finish
material.
20001384
15
SHR Series Woodburning Fireplace
Stud
Finished Wall
Noncombustible
Decorative
Facing
2 x 4 Finished
Header
Covered Wall
Must be Sealed with
Noncombustible
Material
CAUTION: Do Not
Place Finishing
Material Beyond
These Edges or
Cover Air Inlets
Ledge Bracket
Surround
Screen Rail
Hearth
FP1168
FP1167
Fig. 25 Facing on fireplace surround flush with finished wall.
Fig. 26 Finishing front of fireplace.
Face Plate
*
1¹⁄₂"
Ref.
* 12" from top of fireplace opening.
**
Combustible materials are
permitted within a shaded area
shown in Figure 29 titled
Minimum Wall Clearances.
** 6" from top of fireplace opening.
(Noncombustible material must separate the black face surround of the
fireplace and any combustible mantel
material)
MA81
Fig. 27 Combustible mantel clearances.
16
20001384
SHR Series Woodburning Fireplaces
Side Wall Protection
Adjacent combustible side walls that are within dimensions shown in Figure 29 of fireplace opening must be
protected with Wall Shield Model SP40 or a specifically
built wall shield described in Figure 28.
The special wall shield design described in Figure 25 is
an alternate method of adding protection to side walls
and can be used in place of the SP40 with the same
wall clearances specified for the SP40. Rt must =1.85
minimum.
Examples of wall shield insulation:
1. Manville - CERAFORM 126, K=.27,
1/2 inches thick
2. CFM Corporation - EH2416, K = .458,
1 inch thick required.
The top of insulation must be covered with a noncombustible decorative covering or a piece of .018” minimum sheet metal, to protect hearth extension material.
(Fig. 29)
Secure the hearth extension to the floor to prevent
shifting, using trim molding or other similar means at
three (3) outer edges. Seal crack between the fireplace
hearth and hearth extension with a noncombustible
material. (Figs. 29, 31, 32, 33)
WARNING: HEARTH EXTENSION MUST BE INSTALLED IN ACCORDANCE WITH FIGURE 26.
Alternate noncombustible materials may be used
providing the (total) thermal resistance (Rt value) of the
alternate material employed is greater than or equal to
R = 1.09. Thermal resistance (R) or thermal conductivity (K), may be obtained from manufacturer of the
material. Factors are related by the formula K = 1/R.
(Fig. 29)
T = given thickness
R = thermal resistance for a given thickness (T)
K = thermal conductivity
40"
Min.
Noncombustible material with a lower R value may be
used, provided thickness of material is sufficiently
greater to maintain an equivalent (total) thermal resistance (Rt).
40" Min.
Example of Determining
Hearth Extension Equivalents
To determine the thickness required for any new
material:
Decorative
Noncombustible
Rigid Covering
FP838
Noncombustible
Insulation
RT = 1.85 Min.
(Manville Ceraform 126 1/2" Thick or CFM
Corporation EH2416 - 1"
Thick)
Fig. 28 Noncombustible wall shield dimensions.
Hearth Installation
A hearth extension is required to protect a combustible
floor in front of the fireplace. Refer to Figure 29 for
minimum dimensions and mounting detail.
NEW
required
thickness
K of new material (per inch)
=
x
K of listed material (per inch)
thickness
of listed
material
Example for Common Brick
T (new) = 5.0/0.458 x 0.50 in. = 5.46 in. (new required
thickness).
Common Materials And Factors
Material
K*
R
Minimum
Thickness
EH2416
(CFM Corporation)
0.458 1.09
0.50 in.**
NOTE: Hearth Extension must not cover the air
inlet opening of a fireplace.
The hearth extension described in Figure 29 must be a
durable noncombustible material with a minimum (total)
Rt value of 1.09; refer to Figure 30 for examples. The
overall height (above a combustible floor), depth and
width must be as indicated, with the extension centered
to the fireplace opening.
Common Brick 5.0
0.10
5.46 in.**
R Value is for ¹⁄₂ inch.
* Units of K = BTU/SQ FT/HR/ßF/IN
** Thickness of Listed Material
FP533ADD
Fig. 30 Hearth extension material factors.
20001384
17
SHR Series Woodburning Fireplace
Minimum Hearth Extension Dimensions
Minimum Wall Clearances
(for On-Site Construction)
WITH
Noncombustible
Surround Facing
WITHOUT
Noncombustible
Surround Facing
Shaded area starts
1/2" away from
edge of unit
4"
4" Brick
(Example material)
H
G
G
J
E
F**
Firebox
Opening
E
D
A - Min. clearance
to combustible
perpendicular wall
C**
Side
Wall
Side
B - Min. clearance
Wall
to combustible
perpendicular wall when
using noncombustible wall shield*
Combustible material permitted within shaded area.
* Noncombustible wall shield requires 1" CFM Corporation
EH2416 insulation (minimum R Value = 1.85) between
decorative noncombustible rigid covering and combustible wall.
Minimum height and width is 40" x 40".
** Dimension/degree of angle will vary depending on thickness
of noncombustible surround facing.
SHR36
SHR42A
SHR48
SHR52
A
20"
22"
28"
30"
B
12"
18"
18"
20"
C
D
35°
42°
32¹⁄₂° 39¹⁄₂°
26¹⁄₂° 33°
33¹⁄₂° 38¹⁄₂°
Seal cracks
between the
fireplace
and hearth
extension with
noncombustible
material
May install
noncombustible
decorative
covering
OR .018" min.
sheet metal
Fireplace
Hearth
4" Min.
Minimum
Insulation
Value "R":
Combustible
Floor
E
18"
18"
18"
24"
F
14"
14"
14"
20"
G
8"
12"
10"
14"
H
16"
20"
24"
24"
Safety strips
must overlap
¹⁄₂" minimum
J
52"
66"
68"
80"
FP532SHR
Fig. 29 Combustible side wall protection and hearth extension dimensions.
Noncombustible
Decorative Covering
May be Installed
or
.018" Minimum
Sheet Metal
2¹⁄₂" Min.
Seal Cracks Between
Fireplace and Hearth
Extension with
Noncombustible
Material
Seal Cracks Between Fireplace
and Hearth Extension with
Noncombustible Material
8" Max.
Thickness
Lower
Surround
Combustible
Floor
Min. Thickness
(Refer to Table 4)
Minimum Insulation
Value R-3.28
(Refer Table 4)
Fireplace
Hearth
Majestic Safety
Strips Must be
Overlapped 1/2"
Min.
Lower
Surround
Cement
Blocks
Combustible
Floor
1/4" Min.
Thickness
Minimum Insulation
Value R-0.94
FP1169
Fireplace
Hearth
Majestic Safety
Strips Must be
Overlapped 1/2"
Min.
FP1170
Fig. 31 Protection of adjacent combustible side walls and hearth extension dimensions.
18
20001384
SHR Series Woodburning Fireplaces
Wall Covering
2 x 4 Header Do Not Notch at
Ledge Brackets
Fig. 22 or 23
Hearth Extension
Hearth
Extension Insulation
Molding used to
Fasten Hearth
Extension
in Place
Majestic Safety Strips Must
be Overlapped 1/2" Min.
FP1171
Seal Crack Between
Fireplace and Hearth
Extension with
Noncombustible Material
Fig. 32 Sealing detail.
Wall Covering
Noncombustible
Decorative Facing
Seal All Cracks
Between Fireplace
Surround and Wall
Materials with
Noncombustible
Material
Noncombustible
Decorative
Covering
Hearth
Extension
Majestic Safety Strips
Must be Overlapped 1/2"
Min.
2 x 4 Header - Do
Not Notch at
Ledge Brackets
Fig. 24
Seal Crack Between
Fireplace and Hearth
Extension with Noncombustible Material
FP1172
Fig. 33 Sealing detail.
Installing Line for Gas Logs
CFM Specialty Home Product s fireplaces are designed
to accept a 1/2 inch gas line for installation of an approved gas appliance. (CFM Specialty Home Products
manufactures a wide variety of gas logs for use in CFM
Specialty Home Products fireplaces.)
Be sure to have the appliance installed in accordance
with building codes.
Gas connection may enter from either left or right side of
the fireplace.
Locate appropriate gas line in the outer casing of fireplace and remove insulation from gas line tube. (Fig. 34)
From inside the fireplace, locate the knockout on the
firebrick -- be sure you are on the appropriate or "gas
line" side of the fireplace. Using a flat bladed screwdriver
or small chisel and hammer, carefully tap around the
knockout until it loosens and falls out.
Install 1/2 inch certified gas pipe through opening. After
gas pipe installation is complete, use insulation that was
removed from gas line tube to repack space around the
20001384
pipe. Material should be inserted from outside of the
fireplace and packed tightly to totally seal between the
pipe and tube.
Note: Gas pipe should not come in contact with any
wood structures until it has reached a point at least
one (1) inch away from fireplace side.
NOTE: When installing an ANSI Z21.11.2 ventless
appliance, the finishing material used for the mantel must
be rated at 250°F or greater.
BTU input of a gas appliance installed in fireplace should
be rated less than 100,000 BTU/Hr.
Gas pipe installation is intended for connection to a
decorative gas appliance only when (1.) incorporating an
automatic shutoff device and (2.) complying with the
Standard for Decorative Gas Appliances for Installation in
Vented Fireplaces (ANSI Z21.60) or CSA draft requirements for Gas-Fired Log Lighters for Woodburning
Fireplaces (Draft No. 4, August 1993).
Decorative gas appliance should be installed in accordance with the National Fuel Gas Code, ANSI Z223.1
(latest edition).
CAUTION: WHEN USING DECORATIVE
GAS APPLIANCE, FLUE DAMPER MUST
BE SET IN FULLY OPEN POSITION. IF YOU
HAVE GLASS DOORS ON THE FIREPLACE,
THEY MUST ALSO BE FULLY OPENED.
WARNING: DO NOT OPERATE AN UNVENTED GAS LOG SET IN THIS FIREPLACE WITH THE CHIMNEY REMOVED.
WARNING: WHEN INSTALLING AN UNVENTED GAS LOG SET, THE CFM CORPORATION MODEL AH3244BK OR AH3244PB
4" ADJUSTABLE HOOD MUST BE USED.
Hole in Outer Casing
Gas Line
Tubing
1"
Min.
Supply Line
Ceramic
Knockout
Repack Insulation
1/2"
Hole in
Outer Casing
Ceramic Knockout
(both sides)
FP560SHR
Fig. 34 Gas line access.
If installing an unvented gas log set, refer to statement below:
Only unvented gas log sets which have been found to comply with the
Standard for Unvented Room Heaters, ANSI Z21.11.2, are to be
installed in this fireplace.
19
2
7
1
b
c
8
d
a
6
9
5
4
3
10
11
1384
CFM Specialty Home Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time,
without notice.
SHR36/42A/48/52 Woodburning Fireplace
For units FH30RO, GH40RO, HH30RO, IH10RO
1.
2.
3.
4.
5.
6.
7.
8a.
8b.
8c.
8d.
9.
10.
11.
Item/Model Number
Damper Weld Assembly
Damper Handle
Screen Rail
Screen Rod (two per fireplace)
Screen (two per fireplace)
Screen Pull (two per fireplace)
Push Nut (two per fireplace)
Firebrick - Hearth
Firebrick - Back
Firebrick - Left Side
Firebrick - Right Side
Firebrick Retainers (three per fireplace)
Basket Grate
O.S.A. Assy.
SHR36
RP210
20001418
20001429
7554181
7554295
5584139
7512167
20001272
20004165
20004166
20004167
20001432
20004203
20003076
SHR42A
RP210
20001418
20006021
7554199
20001723
5584139
7512167
20005611
20005610
20005612
20005613
20001432
20004203
20003076
SHR48
RP210
20001418
20001431
20001428
20001723
5584139
7512167
20001172
20004147
20004154
20004148
20001432
20004311
20003076
SHR52
RP210
20005322
20005299
20002790
20005278
5584139
7512167
20005303
20005293
20005302
20005304
20001432
20005433
20005762
Accessories
The following accessories for this appliance are available from your local Majestic Fireplaces distributor. Should you
need additional information beyond what your distributor can furnish, contact: CFM Specialty Home Products, 410
Admiral Blvd., Mississauga, Ontario, Canada L5T 2N6 Attn: Technical Services.
CAUTION: This fireplace and chimney assembly is a highly engineered system, and, as such, must be
operated only with CFM Specialty Home Products approved components. If you use an unapproved component to make any modifications, you may create a possible fire hazard and will void the CFM Specialty
Home Products warranty. In addition, such action may void the coverage provided by the owner’s insurance.
Model No.
Accessory
Description
Glass Enclosure Kit
Designed to enclose the fireplace opening
with glass doors allowing the fire to remain
visible. Available in Polished, Brushed
Brass, Black and Pewter
36SHGDKDP/BB/BK/S
42SHGDKTDP/BB/BK/S
48SHGDKDP/BB/BK/S
52SHGDKDP/BB/BK/S
Outside Air Kit
Provides outside air for fuel conbustion in
the firebox. This accessory must be
installed before fireplace is installed.
AK-MST
Hearth Extension
Located on the floor in front of fireplace to
protect the floor from heat, hot embers,
ashes, etc.
EH2416
Hearth Patching Kit
Used to patch cracks in hearth.
HPC1
Wall Shield
Used to protect walls adjacent to the
fireplace.
SP40
Firestop
Required at each floor level and attic on
multi-story installation.
Chimney Support
Used to support the chimney at each 30
feet of vertical height above the hearth and
at every 6 feet of inclined chimney run.
Each support adds 2¹⁄₂" to chimney length.
FS2A (straight flue)
FS6A (30° inclined flue)
11CS (11" flue)
SHR Series Woodburning Fireplace
Accessory
Description
Contemporary Flashing
Required for contemporary top termination
on the roof to prevent rain entry.
8-6-12
(0 to 6/12 pitch)
8-12-12
(6/12 to 12/12 pitch)
Contemporary Chase Top Termination
Used to terminate chimney at the top of a
chase. Adapter kit is included, flashing is
not included.
SLTCF11
Contemporary Round Top Termination
For use with Vermont Castings, Majestic
Products Type "11CF" Chimney Systems.
Used to terminate chimney on the roof.
Flashing not included.
RLTCF11
Extended Round Top
For use with Vermont Castings, Majestic
Products Type "11CF" Chimney Systems.
Used to terminate chimney at top of
chase. Adapter kit included. Flashing not
included.
RLTCF11L
Chimney Sections
Used to build "11CF" chimney systems.
Chimney Elbows
Used to develop 30° offset chimney
systems. (Elbows packed 2 per carton upper and lower elbow set)
Top Housing
with
Upper Baffle
22
Gives traditional chimney top look using
simulated brick in red, tan or white color.
Brick pattern is embossed into galvanized
steel unit. Roof flashing is included.
Appropriate adapter is required. Must be
used with upper baffle.
Model No.
11" flue
11CF1 (1' long)
11CF18 (1¹⁄₂' long)
11CF3 (3' long)
11CF4 (4' long)
11CF30-2
(11" 30° flue)
S20BR/BT/BW
S20UB (Upper Baffle)
20001384
SHR Series Woodburning Fireplaces
™
LIMITED WARRANTY & 30 YEAR PROTECTION PLAN
For MAJESTIC FIREPLACES® PRE-ENGINEERED Fireplace Systems
CFM Specialty Home Products warrants its MAJESTIC
FIREPLACES® Pre-Engineered Fireplace (“Fireplace”) and the
CFM Specialty Home Products supplied firegrate, glass doors,
outside air system, fan motor, and liners to be free from defects
in material or workmanship, as follows:
A. Fireplace and Chimney Components: (exclusive of CFM
Specialty Home Products-supplied firegrate, glass doors, outside
air system, fan motor, and liners all of which are covered by
separate warranties under paragraphs B through D below): At its
option for a period of thirty (30) years from the date the Fireplace
is installed, CFM Specialty Home Products will;
(1) For a period of five (5) years from the date the Fireplace is
installed, CFM Specialty Home Products, at its option, will repair
or replace any defective part without charge.
(2) Thereafter, through the 10th year after the date the
Fireplace is installed, if replacement parts are available, CFM
Specialty Home Products will provide a replacement for any
defective part without charge for the part itself. The consumer
must pay for everything else other than the part.
(3) Thereafter, through the 30th year after the date the
Fireplace is installed, if replacement parts are available,CFM
Specialty Home Products will provide a replacement for any
defective part at a cost to the consumer of CFM Specialty Home
Products then current list price, FOB CFM Specialty Home
Products factory.
B. Firegrate, Glass Doors, Outside Air System:
For a period of 90 days from the date the Fireplace is installed
CFM Specialty Home Products, at its option, will provide a
replacement for any defective part, without charge for the part
itself, FOB CFM Specialty Home Products factory, (The consumer must pay for everything else other than the part,).
C. Fan Motor:
(1) For a period of one (1) year from the date the Fireplace is
installed, CFM Specialty Home Products, at its option, will repair
or replace any defective part without charge.
(2) Thereafter, through the 30th year after the date the
Fireplace is installed CFM Specialty Home Products, at its
option, if replacement parts are available, will provide a replacement for any defective part at a cost to the consumer of CFM
Specialty Home Products then current list price, FOB CFM
Specialty Home Products factory.
D. Liners (Refractory or Metal):
(1) For a period of two (2) years from the date the Fireplace is
installed, CFM Specialty Home Products, at its option, will repair
or replace any defective part without charge.
(2) Thereafter, through the 30th year after the date the
Fireplace is installed CFM Specialty Home Products, if replacement parts are available, will provide a replacement for any
defective part at a cost to the consumer of CFM Specialty Home
Products then current list price, FOB CFM Specialty Home
Products factory.
This warranty is subject to the following conditions and limitations:
(1) This warranty is extended only to a Fireplace installed in
the continental United States, the state of Alaska and Canada;
only if and so long as the Fireplace is installed according to the
installation instructions furnished with the Fireplace, and
operated at all times under normal conditions, use and service
20001384
according to the operative instructions furnished with the
Fireplace, and only if and so long as the Fireplace is not
removed from its original installation.
(2) This warranty is non-transferrable, and is made to the
original owner, provided that the purchase was made through an
authorized supplier of the Company.
(3) The sole and exclusive remedies for breach of any
warranties hereunder shall be for the repair, replacement or
provision of a replacement part at CFM Specialty Home Products
then current list price, FOB CFM Specialty Home Products
factory, for any defective part as specified in paragraphs A
through D.
(4)CFM Specialty Home Products shall not be liable for
damage from any smoking of a MAJESTIC FIREPLACES PreEngineered Fireplace System related to environmental geographic conditions (such as, for example, nearby structures or
roof peaks, trees, hills, or mountains), inadequate ventilation, or
negative air pressure in the place where the Fireplace system is
installed, related to any mechanical system (such as, for
example, furnaces, fans, air conditioners, clothes dryers, etc.)
(5) Except as otherwise expressly specified in paragraphs A
through D, NONE OF THESE WARRANTIES COVER, AND
CFM SPECIALTY HOME PRODUCTS SHALL NOT BE RESPONSIBLE FOR, ANY CONSTRUCTION, INSTALLATION,
LABOR, TRANSPORTATION OR OTHER COSTS OR EXPENSES ARISING FROM A DEFECTIVE PART, ITS REPAIR OR
REPLACEMENT OR OTHERWISE, NOR SHALL CFM SPECIALTY HOME PRODUCTS IN ANY EVENT BE RESPONSIBLE
FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES EXCEPT TO THE EXTENT REQUIRED BY LAW.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, so this exclusion or limitation may not
apply to you.
NO IMPLIED WARRANTIES, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL REMAIN IN EFFECT AFTER
THE EXPIRATION OF THE WARRANTIES SET FORTH IN
PARAGRAPHS A THROUGH D. Some states do not allow
limitations on how long an implied warranty lasts, so this
limitation may not apply to you.
In order to obtain performance of any of the above warranty
obligations write to CFM Specialty Home Products at this
address:
CFM Specialty Home Products
410 Admiral Blvd.
Mississauga, Ontario, Canada L5T 2N6
Attention: Director of Warranty Services
Since local building requirements may vary greatly throughout
the country, users of CFM Specialty Home Products products
should determine in advance whether there are any building
code restrictions on the use of a specific product. CFM SPECIALTY HOME PRODUCTS MAKES NO REPRESENTATION
OR WARRANTY REGARDING, AND SHALL NOT BE RESPONSIBLE FOR, ANY BUILDING CODE COMPLIANCE.
The foregoing warranties give you specific legal rights and you
may also have other rights which vary from state to state.
23
CFM Specialty Home Products
410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777
www.majesticproducts.com • www.vermontcastings.com
© CFM Specialty Home Products
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising