Encore LT Manual Spray System

Encore LT Manual Spray System
Encorer LT
Manual Powder Spray Systems
Customer Product Manual
Part 1604857-11
Issued 09/16
For parts and technical support, call the
Finishing Customer Support Center at (800) 433-9319.
This document is subject to change without notice.
Check http://emanuals.nordson.com/finishing for the latest version.
NORDSON CORPORATION  AMHERST, OHIO  USA
Contact Us
Nordson Corporation welcomes requests for information, comments, and
inquiries about its products. General information about Nordson can be
found on the Internet using the following address:
http://www.nordson.com.
Address all correspondence to:
Nordson Corporation
Attn: Customer Service
555 Jackson Street
Amherst, OH 44001
Notice
This is a Nordson Corporation publication which is protected by copyright.
Original copyright date 2013. No part of this document may be
photocopied, reproduced, or translated to another language without the
prior written consent of Nordson Corporation. The information contained
in this publication is subject to change without notice.
Trademarks
Encore, Nordson, and the Nordson logo are registered trademarks of
Nordson Corporation.
Betasolv is a registered trademark of Oakite Corporation, Inc.
All other trademarks are the property of their respective owners.
Part 1604857-11
E 2016 Nordson Corporation
Change Record
i
Change Record
Revision
Date
01
10/13
Original publication date
02
01/14
New flat spray electrode holder and assembly, new conical nozzle kit and
conical electrode assembly
03
05/14
Page 7−3, new trigger axle P/N 1605713
Page 7−5, new nozzle P/N’s
04
06/14
New flat and conical electrode holders
05
01/15
New lance extension added to parts section
06
04/15
Replaced part number 1108310 with part number 1606835 and edited
NFC mode info in Operation
07
03/16
Cleaning procedure added
08
04/16
Updated safety labels
09
05/16
Added trigger kit
10
08/16
Added power supply kits
11
09/16
Nozzle and lance extension part number change
E 2016 Nordson Corporation
Change
Part 1604857-11
ii
Change Record
Part 1604857-11
E 2016 Nordson Corporation
Table of Contents
iii
Table of Contents
E 2016 Nordson Corporation
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Qualified Personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regulations and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Personal Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fire Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Action in the Event of a Malfunction . . . . . . . . . . . . . . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-1
1-1
1-1
1-2
1-2
1-3
1-3
1-3
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mobile System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rail-Mount System Components . . . . . . . . . . . . . . . . . . . . . . . .
Wall-Mount System Components . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mobile System with VBF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mobile System with 50Lb. Feed Hopper . . . . . . . . . . . . . . . . . .
Equipment Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powder Spray Gun Certification Labels . . . . . . . . . . . . . . . . . .
Controller Certification Label . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-1
2-2
2-2
2-2
2-3
2-3
2-3
2-4
2-4
2-4
Part 1604857-11
iv
Table of Contents
System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Rail Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VBF System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feed Hopper and Wall/Rail Mount System Setup . . . . . . . . . . . .
Adapter Kit or Coupling Installation − Wall/Rail Mount Systems
Coupling Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adapter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spray Gun Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gun Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Tubing and Powder Hose . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bundling Tubing and Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Air Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Air Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mobile Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wall/Rail Mount Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vibratory Box Feeder Settings . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shut Off Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exiting Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Part 1604857-11
3-1
3-1
3-2
3-3
3-3
3-4
3-5
3-8
3-10
3-10
3-10
3-11
3-11
3-12
3-13
3-13
3-13
3-13
3-13
3-15
3-15
3-15
3-16
3-16
3-16
3-17
3-17
3-17
3-17
3-17
E 2016 Nordson Corporation
Table of Contents
E 2016 Nordson Corporation
v
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
European Union, ATEX, Special Conditions for Safe Use . . . . .
Controller Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Power Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displays and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrostatic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Select Charger Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Custom Electrostatic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Classic Electrostatic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Classic Standard (STD) Mode . . . . . . . . . . . . . . . . . . . . . . . .
Classic AFC Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Encore Nano Feedback Control Mode (NFC) . . . . . . . . . . . . . .
Powder Flow Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Smart Flow Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Classic Flow Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spray Gun Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrode Air Wash Operation . . . . . . . . . . . . . . . . . . . . . . . . . .
Daily Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Purging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powder Box Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vibratory Box Feeder Operation . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Flat Spray Nozzles . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Conical Nozzles and Deflectors . . . . . . . . . . . . . . . .
Installing the Optional Pattern Adjuster Kit . . . . . . . . . . . . . . . .
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Cleaning Procedure for Powder Contact Parts
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4-1
4-1
4-1
4-2
4-2
4-2
4-3
4-3
4-3
4-4
4-4
4-4
4-5
4-6
4-7
4-7
4-7
4-7
4-8
4-8
4-9
4-10
4-11
4-12
4-12
4-13
4-13
4-14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spray Gun Power Supply Resistance Test . . . . . . . . . . . . . . . . . .
Electrode Assembly Resistance Test . . . . . . . . . . . . . . . . . . . . . . .
Gun Cable Continuity Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
5-1
5-2
5-6
5-6
5-7
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spray Gun Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply and Powder Path Replacement . . . . . . . . . . . .
Gun Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gun Disassembly (contd) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Replacement . . . . . . . . . . . . . . . . . . . . . . . . . .
Powder Path Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powder Path Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gun Re-Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trigger Switch Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch Installation (contd) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vibrator Motor Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1
6-1
6-1
6-1
6-2
6-2
6-3
6-4
6-4
6-5
6-5
6-6
6-6
6-6
6-7
6-8
6-9
6-9
6-10
6-11
Part 1604857-11
vi
Table of Contents
Part 1604857-11
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spray Gun Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spray Gun Parts Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spray Gun Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spray Gun Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Miscellaneous Spray Gun Options . . . . . . . . . . . . . . . . . . . . . . .
Flat Spray Nozzles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cross-Cut Nozzles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45-Degree Corner-Spray Nozzle . . . . . . . . . . . . . . . . . . . . . . . . .
45-Degree In-Line Flat-Spray Nozzle . . . . . . . . . . . . . . . . . . . .
Conical Nozzle, Deflectors and Electrode Assembly Parts . . .
Conical Nozzle and Deflectors . . . . . . . . . . . . . . . . . . . . . . . .
Conical Nozzle Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conical Electrode Assembly . . . . . . . . . . . . . . . . . . . . . . . . . .
Pattern Adjuster Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lance Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pattern Adjuster Kit for Lance Extensions . . . . . . . . . . . . . . . .
Ion Collector Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ion Collector Components for Lance Extensions . . . . . . . . . .
Controller Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel and Internal Cabinet Ground Parts Illustration . .
Front Panel and Internal Cabinet Ground Parts List . . . . . . . .
Rear Panel Parts Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Panel Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manifold Illustration and Parts List . . . . . . . . . . . . . . . . . . . . . . .
System Components and Parts . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powder Hose and Air Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Transportable Manual System . . . . . . . . . . . . . . . . . .
7-1
7-1
7-1
7-1
7-2
7-3
7-4
7-4
7-5
7-5
7-6
7-6
7-7
7-7
7-7
7-7
7-8
7-8
7-8
7-9
7-9
7-10
7-10
7-11
7-12
7-13
7-14
7-15
7-16
7-16
7-17
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1
E 2016 Nordson Corporation
Safety
1-1
Section 1
Safety
Introduction
Read and follow these safety instructions. Task- and equipment-specific
warnings, cautions, and instructions are included in equipment
documentation where appropriate.
Make sure all equipment documentation, including these instructions, is
accessible to all persons operating or servicing equipment.
Qualified Personnel
Equipment owners are responsible for making sure that Nordson equipment
is installed, operated, and serviced by qualified personnel. Qualified
personnel are those employees or contractors who are trained to safely
perform their assigned tasks. They are familiar with all relevant safety rules
and regulations and are physically capable of performing their assigned
tasks.
Intended Use
Use of Nordson equipment in ways other than those described in the
documentation supplied with the equipment may result in injury to persons
or damage to property.
Some examples of unintended use of equipment include
S
S
S
S
S
S
using incompatible materials
making unauthorized modifications
removing or bypassing safety guards or interlocks
using incompatible or damaged parts
using unapproved auxiliary equipment
operating equipment in excess of maximum ratings
Regulations and Approvals
Make sure all equipment is rated and approved for the environment in which
it is used. Any approvals obtained for Nordson equipment will be voided if
instructions for installation, operation, and service are not followed.
All phases of equipment installation must comply with all federal, state, and
local codes.
E 2016 Nordson Corporation
Part 1604857-11
1-2
Safety
Personal Safety
To prevent injury follow these instructions.
S Do not operate or service equipment unless you are qualified.
S Do not operate equipment unless safety guards, doors, or covers are
intact and automatic interlocks are operating properly. Do not bypass or
disarm any safety devices.
S Keep clear of moving equipment. Before adjusting or servicing any
moving equipment, shut off the power supply and wait until the
equipment comes to a complete stop. Lock out power and secure the
equipment to prevent unexpected movement.
S Relieve (bleed off) hydraulic and pneumatic pressure before adjusting or
servicing pressurized systems or components. Disconnect, lock out, and
tag switches before servicing electrical equipment.
S Obtain and read Safety Data Sheets (SDS) for all materials used. Follow
the manufacturer’s instructions for safe handling and use of materials,
and use recommended personal protection devices.
S To prevent injury, be aware of less-obvious dangers in the workplace
that often cannot be completely eliminated, such as hot surfaces, sharp
edges, energized electrical circuits, and moving parts that cannot be
enclosed or otherwise guarded for practical reasons.
Fire Safety
To avoid a fire or explosion, follow these instructions.
S Do not smoke, weld, grind, or use open flames where flammable
materials are being used or stored.
S Provide adequate ventilation to prevent dangerous concentrations of
volatile materials or vapors. Refer to local codes or your material SDS
for guidance.
S Do not disconnect live electrical circuits while working with flammable
materials. Shut off power at a disconnect switch first to prevent sparking.
S Know where emergency stop buttons, shutoff valves, and fire
extinguishers are located. If a fire starts in a spray booth, immediately
shut off the spray system and exhaust fans.
S Clean, maintain, test, and repair equipment according to the instructions
in your equipment documentation.
S Use only replacement parts that are designed for use with original
equipment. Contact your Nordson representative for parts information
and advice.
Part 1604857-11
E 2016 Nordson Corporation
Safety
1-3
Grounding
WARNING: Operating faulty electrostatic equipment is hazardous and can
cause electrocution, fire, or explosion. Make resistance checks part of your
periodic maintenance program. If you receive even a slight electrical shock
or notice static sparking or arcing, shut down all electrical or electrostatic
equipment immediately. Do not restart the equipment until the problem has
been identified and corrected.
Grounding inside and around the booth openings must comply with NFPA
requirements for Class II, Division 1 or 2 Hazardous Locations. Refer to
NFPA 33, NFPA 70 (NEC articles 500, 502, and 516), and NFPA 77, latest
conditions.
S All electrically conductive objects in the spray areas shall be electrically
connected to ground with a resistance of not more than 1 megohm as
measured with an instrument that applies at least 500 volts to the circuit
being evaluated.
S Equipment to be grounded includes, but is not limited to, the floor of the
spray area, operator platforms, hoppers, photoeye supports, and
blow-off nozzles. Personnel working in the spray area must be
grounded.
S There is a possible ignition potential from the charged human body.
Personnel standing on a painted surface, such as an operator platform,
or wearing non-conductive shoes, are not grounded. Personnel must
wear shoes with conductive soles or use a ground strap to maintain a
connection to ground when working with or around electrostatic
equipment.
S Operators must maintain skin-to-handle contact between their hand and
the gun handle to prevent shocks while operating manual electrostatic
spray guns. If gloves must be worn, cut away the palm or fingers, wear
electrically conductive gloves, or wear a grounding strap connected to
the gun handle or other true earth ground.
S Shut off electrostatic power supplies and ground gun electrodes before
making adjustments or cleaning powder spray guns.
S Connect all disconnected equipment, ground cables, and wires after
servicing equipment.
Action in the Event of a Malfunction
If a system or any equipment in a system malfunctions, shut off the system
immediately and perform the following steps:
S Disconnect and lock out electrical power. Close pneumatic shutoff
valves and relieve pressures.
S Identify the reason for the malfunction and correct it before restarting the
equipment.
Disposal
Dispose of equipment and materials used in operation and servicing
according to local codes.
E 2016 Nordson Corporation
Part 1604857-11
1-4
Safety
Part 1604857-11
E 2016 Nordson Corporation
Description
2-1
Section 2
Description
Introduction
See Figure 2-1. This manual covers all versions of the Encore LT Manual
Powder Spray System:
S
S
S
S
Mobile system with vibratory box feeder
Mobile system with feed hopper
Rail-mount system
Wall-mount system
Mobile System with Hopper
Figure 2-1
Mobile System with Vibratory Box Feeder
Encore LT Mobile Manual Powder Systems
NOTE: The Encore LT Manual Powder Spray System is also available as a
transportable demonstration system which includes the components listed
in Section 7, Parts.
E 2016 Nordson Corporation
Part 1604857-11
2-2
Description
Mobile System Components
Mobile systems include:
S
S
S
S
S
Encore LT manual controller
Encore LT manual spray gun
Encore Generation II powder feed pump
Encore pump pickup tube
One of the following, based on system version:
S Vibratory table and motor − fluidizes a 25- or 50-lb box of powder
S 50-lb Encore round feed hopper − fluidizes powder with low-pressure
compressed air
S 11-mm powder hose, air tubing, spiral wrap, Velcro straps
The components are mounted on a sturdy two-wheeled dolly.
Rail-Mount System Components
Rail-mount systems include:
S
S
S
S
S
S
S
S
Encore LT manual controller
Encore LT manual spray gun
Encore Generation II powder feed pump
Pump adapter kit and coupling for use on HR/NHR feed hoppers
Rail-mount bracket kit
Grounding kit
11-mm powder hose, air tubing, spiral wrap, Velcro straps
Air filter kit
NOTE: Powder can be also be supplied from an Encore in-line pump
mounted in a feed center.
Wall-Mount System Components
Wall-mount systems include a
S
S
S
S
S
S
S
S
Encore LT manual controller
Encore LT manual spray gun
Encore Generation II powder feed pump
Pump adapter kit and coupling for use on HR/NHR feed hoppers
Wall-mount bracket kit
Grounding kit
11-mm powder hose, air tubing, spiral wrap, Velcro straps
Air filter kit
NOTE: Powder can be also be supplied from an Encore in-line pump
mounted in a feed center.
Part 1604857-11
E 2016 Nordson Corporation
Description
2-3
Specifications
Model
Input Rating
Output Rating
ENCORE Applicator
+/− 19 VAC, 1 A
100 KV, 100 A
ENCORE Controller
100−250 VAC, 50/60 Hz
N/A
Vibratory Motor 50 Hz
230 VAC, +/− 10%
N/A
Vibratory Motor 60 Hz
115 VAC, +/− 10%
N/A
S Input Air: 4.0−7.6 bar (58−110 psi), <5 particulates, dew point <10 _C
(50 _F)
S Max Relative Humidity: 95% non-Condensing
S Ambient Temperature Rating: +15 to +40 _C (59−104 _F)
S Hazardous Location Rating for Applicator: Zone 21 (EU) or Class II,
S
S
S
Division 1, Group F and G
Hazardous Location Rating for Controller: Zone 22 (EU) or Class II,
Division 2, Group F and G
Dust Ingress Protection: IP6X
Vibrator Table Capacity: 25 kg (50 lb) box of powder
Mobile System with VBF
Height:
Length:
Wheel Base:
Weight:
995 mm (35.2 in.)
820 mm (32.25 in.)
598.5 mm (23.5 in.)
46.7 kg (103 lbs)
Mobile System with 50Lb. Feed Hopper
Height:
Length:
Wheel Base:
Weight:
E 2016 Nordson Corporation
995 mm (35.2 in.)
812 mm (32 in.)
598.5 mm (23.5 in.)
50.4 kg (111 lbs)
Part 1604857-11
2-4
Description
Equipment Labels
Powder Spray Gun Certification Labels
ÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏ
Controller Certification Label
ENCORE LT
EN 50050 FM11ATEX0057X
(2) 3 D
Ex tc IIIC T60C Dc
TA = +15 to +40C
NORDSON CORP. AMHERST, OH, USA
Vn=100−250Vac 7n=50−60Hz Pn=100VA
OUTPUT: V(peak)= +19V Io(peak)= +1.0A
WARNING − POTENTIAL ELECTROSTATIC CHARGING
HAZARD, SEE INSTRUCTION MANUAL.
Part 1604857-11
E 2016 Nordson Corporation
System Setup
3-1
Section 3
System Setup
Controller Rail Mounting
See Figure 3-1. Rail mount systems are shipped with a bracket kit, small
parts tray kit, and bus-bar grounding kit.
1. Install the controller bracket (1) on the bottom of the controller with four
M5 x 12 black pan head screws (2) and one #10 dished lock washer (9).
2. Install the controller bracket (1) on the rail bracket (5) with two M8 split
lock washers (7) and two M8 x 70 hex head cap screws (8).
3. Thread the two M8 jam nuts (4) onto the two M8 x 40 screws (3), then
thread the two screws into the holes in the rail bracket.
2
9
10
1
9
2
6
3
4
5
7
8
Figure 3-1
1.
2.
3.
4.
Rail Mount Kit and Parts Tray Installation
Controller bracket
M5 x 12 screws
M8 x 40 screws
M8 jam nuts
E 2016 Nordson Corporation
5. Rail bracket
6. Rail
7. M8 lock washers
8. M8 x 70 screws
9. #10 dished lock washer
10. Parts tray
Part 1604857-11
3-2
System Setup
Controller Rail Mounting (contd)
4. Install the rail bracket over the operator platform railing (6), tighten the
screws (3) against the rail, then tighten the jam nuts (4) up against the
rail bracket to prevent the screws from loosening.
5. Install the parts tray (11) in the front two holes on top of the controller
using two of the M5 screws (2) in the controller top, and one #10 dished
lock washer (9) included in the kit.
6. Use the bus-bar grounding kit to connect the controller ground stud to
the booth base, as described in the grounding kit instructions.
Controller Wall Mounting
See Figure 3-2. Wall-mount systems are shipped with a bracket kit that
includes the wall-mount bracket and the fasteners required to secure the
controller to the bracket. The bracket allows the controller to be installed
perpendicular to the wall or at an angle, in 30 degree increments.
1. Install the bracket on the wall with 3/8-in. fasteners (not included).
2. Install the controller on the bracket with the supplied screws and
washers, including the single dished washer. The washer provides a
ground connection between the controller and the bracket.
3. Use the bus-bar grounding kit to connect the controller ground stud to
the booth base, as described in the grounding kit instructions.
Dished Washer
Figure 3-2
Part 1604857-11
Wall-Mount Bracket Installation
E 2016 Nordson Corporation
System Setup
3-3
System Connections
System Diagram
WARNING: This diagram does not show all system grounds. All conductive
equipment in the spray area must be connected to a true earth ground.
NOTE: The input air filter shown in this diagram is mounted behind the
front panel of mobile systems. For rail- or wall-mount systems, the filter and
mounting bracket are shipped in a kit for mounting at the customer’s plant.
Spray Gun
Keypad
Encore LT
Controller
Gun cable
Fluidizing Air
Atomizing Air
Flow-Rate Air
4mm clear
6mm black
8mm blue
8mm black
Air Wash Air
Purge Air
Filter
Sol. & Regulator Wiring
24VDC
Main Control Board
6mm blue
Pump
6mm blue*
Manifold
10mm
Powder hose
6mm black
Conductive*
Pickup Tube
6mm blue**
10mm
Input Air
Power
Supply
Relay
Board
AC Power Cord
Feed
Hopper**
VBF Power Cord*
Line
Filter
Powder Box*
Dolly or Booth
Ground
VIibrator Motor*
* VBF System
** Hopper System
Figure 3-3
Encore LT Manual Powder System Block Diagram
E 2016 Nordson Corporation
Part 1604857-11
3-4
System Setup
Controller Connections
The rear panel of the controller provides connections for power, ground,
vibrator motor, gun, pump, and fluidizing air.
9
1
10
7
8
11
2
6
3
5
4
GND
L1
(GRN/YEL)
L2
(BROWN)
(BLUE)
Figure 3-4
1.
2.
3.
4.
Encore LT Gun Controller Connections
Electrostatic ground (to cart or booth)
Vibrator motor power cord
Power cord (15ft)
Atomizing air (blue, 8mm, to pump)
Part 1604857-11
5. Air supply (blue, 10mm)
6. Flow-rate air (black, 8mm, to
pump)
7. Gun cable (to gun)
8. Purge air (black, 6mm, to gun)
9. Fluidizing air (blue, 6mm, to
pickup tube or hopper)
10. Fluidizing air needle valve
11. Air wash (clear, 4mm, to gun)
E 2016 Nordson Corporation
System Setup
3-5
VBF System Setup
This procedure applies to mobile systems with a vibratory box feeder.
1. Unpack the pickup arm, collar and set screw, pickup tube, and pump.
2. See Figure 3-5. Install the pickup arm as shown, using four M5 x 10
screws with integral washers (3).
1
3
2
Figure 3-5
Pickup Arm Installation
1. Arm
2. Arm bracket
3. M5 x 10 screws (x 4)
3. See Figure 3-6. Install the collar (1) on the pickup tube (2) as shown.
Tighten the socket-head screw to secure the collar.
4
1
2
3
Figure 3-6
Collar Installation on Pickup Tube
1. Collar
2. M5 socket head screw (black)
E 2016 Nordson Corporation
3. Pickup tube
4. Pump mount
Part 1604857-11
3-6
System Setup
VBF System Setup (contd)
4. See Figure 3-7. Swing the tube bracket out of the way and install the
pickup tube (1) in the arm.
5. Install the pump (3) into the pump mount (2) with a slight twisting
motion.
2
4
3
1
Figure 3-7
Encore LT Gun Pickup Tube and Pump Installation
1. Pickup tube
2. Pump
3. Tube bracket
4. Pump mount
6. Unpack the air tubing, powder hose, clamps, and Velcro straps shipped
with the system.
7. See Figure 3-4. Plug the shorter lengths of the tubing into the controller:
S 8-mm blue atomizing air tubing (4)
S 8-mm black flow-rate air tubing (6)
S 6-mm blue fluidizing air tubing (9)
8. See Figure 3-8. Route the tubing (4, 6, 9) through the grommet in the
front panel of the cart tower as shown.
9. Connect the tubing and powder hose as shown:
S
S
S
S
S
8-mm blue atomizing air tubing (4) to the pump top fitting
8-mm black flow-rate air tubing (6) to the pump bottom fitting
6-mm blue fluidizing air tubing (9) to the bulkhead union (1)
6-mm black fluidizing air tubing (2) to the union and pick-up tube.
powder hose (7) to the pump—secure with hose clamp (3)
NOTE: Before securing the pump and fluidizing air tubing to the pickup
arm, provide a service loop in the tubing to allow for lifting and removing the
pickup tube and pump from the arm without disconnecting the tubing.
10. Secure the tubing to the arm with blue Nordson Velcro straps (5).
Part 1604857-11
E 2016 Nordson Corporation
System Setup
3-7
Create Service Loop Here
7
3
6*
4*
2*
5
2
1
9
12
Figure 3-8
Encore LT Gun Pickup Tube and Pump Installation
1. Bulkhead union
2. 6-mm black fluidizing air tubing*
3. Hose clamp
4. Blue 8-mm atomizing tubing*
5. Velcro straps
6. Black 8-mm flow-rate tubing*
7. Powder hose
9. Blue 6-mm fluidizing tubing
12. Grommet
Note: * Create service loop as noted before securing tubing to arm with straps.
WARNING: The black fluidizing air tubing (2), the pickup tube connector,
and the bulkhead union (1) are conductive and provide a ground path to the
cart. Do not replace these components with non-conductive components.
Refer to Parts for replacement tubing.
NOTE: The pump is equipped with quick-connect couplings that allow you
to quickly disconnect the air tubing when cleaning or repairing the pump.
Pull back on the knurled coupling rings to uncouple them.
E 2016 Nordson Corporation
Part 1604857-11
3-8
System Setup
Feed Hopper and Wall/Rail Mount System Setup
This procedure applies to mobile systems, and wall or rail mount systems
supplied with powder from a feed hopper.
1. Unclamp the hopper lid and take out the vent hose and hose clamps.
Re-clamp the lid.
2. Unpack the pump, powder hose, air tubing, clamps, and Velcro straps
shipped with the system.
3. See Figure 3-4. Plug the following into the controller:
S 8-mm blue atomizing air tubing (4)
S 8-mm black flow-rate air tubing (6)
S 6-mm blue fluidizing air tubing (9)
4. See Figure 3-9. Route the atomizing air (4) and flow-rate tubing (6)
through the grommet (12) on the front panel of the cart tower.
5. Route the fluidizing air (9) tubing through the tower and out the bottom
front.
6. Mobile systems: Install the hopper on the cart platform, in between the
retainer tabs.
7. Install the pump (7) into the pump mount (5) with a slight twisting
motion. Connect the fluidizing and atomizing air tubing to the pump as
shown.
NOTE: Rail mount systems are shipped with a pump adapter kit and a
coupling for use with pickup tubes designed for other pumps. Refer to the
installation instructions on page 3-10.
8. Connect the 10-mm x 6-mm reducer (11) to the 10-mm elbow fitting on
the hopper fluidizing pan. Connect the fluidizing air tubing (9) to the
reducer.
9. Connect the ring-tong terminal on the green/yellow ground wire (10) to
the ground stud on the side of the fluidizing pan, then plug the ground
wire into the grounding socket on the cart base.
10. Install a hose clamp (8) over the end of the vent hose (1) and connect
the hose to the vent stack on the lid. Tighten the clamp to secure the
hose.
11. Connect the powder hose (2) to the pump and secure it with a hose
clamp (3).
NOTE: The pump is equipped with quick-connect couplings that allow you
to quickly disconnect the air tubing when cleaning or repairing the pump.
Pull back on the knurled coupling rings to uncouple them.
Part 1604857-11
E 2016 Nordson Corporation
System Setup
7
3
6
1
2
3-9
4
5
12
8
4
6
9
Figure 3-9
1.
2.
3.
4.
10
11
Encore LT Mobile System with Hopper − Hopper and Pump Installation
Vent hose
Powder hose
Hose clamp
Blue atomizing air tubing
E 2016 Nordson Corporation
5.
6.
7.
8.
Pump mount
Black flow-rate air tubing
Pump
Vent hose clamp
9.
10.
11.
12.
Blue fluidizing air tubing
Ground wire
10 x 6 mm reducer fitting
Grommet
Part 1604857-11
3-10 System Setup
Adapter Kit or Coupling Installation − Wall/Rail Mount Systems
Rail- and wall-mount systems are shipped with a pump adapter kit and a
coupling that allows the Encore pump to be used on HR and NHR hopper
pickup tubes that were designed for other types of pumps. The adapter kit
provides a permanent mounting and its use is recommended.
Coupling Installation
The coupling allows you to use the existing pump adapter.
1. Install the pump coupling on the existing pump adapter with a slight
twisting motion.
2. Install the Encore pump into the coupling with a slight twisting motion.
Adapter Installation
The adapter kit replaces existing pump adapters with external O-rings on all
threaded 0.360 in. ID pickup tubes.
1. Pull the pump adapter and pickup tube out of the pump mount on the
hopper lid.
2. Unscrew the pickup tube from the existing adapter.
3. Screw the pickup tube into the Encore pump adapter shipped with the
system.
4. Install the pump adapter and pickup tube into the pump mount.
5. Install the Encore pump into the pump adapter with a slight twisting
motion.
2. Replace With
Encore Adapter
1. Remove
Existing Adapter
Pump
Coupling
Pump
Adapter
Coupling Installation
Figure 3-10
Part 1604857-11
Hopper
Pickup Tube
Assembly
Adapter Installation
Pump Mounting
E 2016 Nordson Corporation
System Setup
3-11
Spray Gun Connections
Unpack the spray gun. Uncoil the cable, the 4-mm clear and 6-mm black air
tubing, and the 11-mm powder hose. Make the following connections:
Gun Cable
See Figure 3-11.
1. Connect the gun cable to the GUN receptacle on the rear panel of the
controller. The cable plug and receptacle are keyed.
2. Thread the cable nut onto the receptacle and tighten the nut securely.
3. Secure the cable strain relief to the rear panel with one of the existing
panel screws.
Mobile System
Rail/Wall Mount System
Strain Relief
Figure 3-11
Gun Cable Connection and Strain Relief Mounting
E 2016 Nordson Corporation
Part 1604857-11
3-12 System Setup
Air Tubing and Powder Hose
1. See Figure 3-12. Connect the 6-mm black air tubing to the
quick-disconnect fitting in the gun handle.
2. Connect the 4-mm clear electrode air wash tubing to the barbed fitting in
the gun handle.
4-mm Clear Electrode
Air Wash Tubing
Hose Adapter
6-mm Black
Purge Air Tubing
Gun Cable
Powder Hose
Figure 3-12
Gun Connections
3. Connect the powder hose to the hose adapter, then plug the hose
adapter into the handle.
NOTE: 6 meters (20 ft) of 11 mm ID powder hose is shipped with the
system. If you must use a longer hose, switch to 1/2 inch ID powder hose.
Refer to Parts for hose part numbers.
4. Route the air tubing to the rear panel of the gun controller.
5. See Figure 3-4. Connect the 6-mm black tubing to the purge air
quick-disconnect fitting (8).
6. See Figure 3-13. Connect the 4-mm clear tubing and the flow control
valve supplied with the system to the air wash connector on the rear
panel as shown. The flow control valve can be located anywhere
desired. Use a tubing cutter to make sure the tube ends are square.
Air Wash Connector
Flow Control Valve
To Gun
4-mm Tubing
Figure 3-13
Flow Control Valve and Air Wash Tubing Connection
Part 1604857-11
E 2016 Nordson Corporation
System Setup
3-13
Bundling Tubing and Cable
Use the sections of black spiral-cut tubing supplied with the system to
bundle together the spray gun cable, air tubing, and powder hose. Coil the
bundled tubing and cable and hang the coil on the hook at the back of the
cart tower.
System Air Connections
System Air Supply
Compressed air should be supplied from an air drop equipped with a
self-relieving shutoff valve. The air must be clean and dry. A refrigerant or
desiccant-type air drier and air filters are recommended.
All systems are shipped with a 0.3-micron air filter. It is important that the
filter be used to prevent contamination of the system pneumatic
components and the powder supply.
Supply air pressure should be 4.0−7.6 bar (58−110 psi).
To provide air to your system, an input air kit with connectors, couplings,
and 10-mm air tubing (15-ft for dolly systems, 25-ft for wall/rail mount
systems) is available.
Refer to the Parts section for filter kits, replacement elements, and input air
kit part numbers and ordering information.
Mobile Systems
Connect 10-mm air tubing from your compressed air supply to the air input
fitting on the rear panel of the dolly.
Wall/Rail Mount Systems
See Figure 3-14.
1. Use the mounting bracket (4) as a template to mark and drill mounting
holes in the selected mounting surface. Make sure there is sufficient
clearance to connect air tubing and change the filter element.
2. Install the two male connectors (2) included in the kit in the filter input
and output ports.
3. Install the mounting bracket on the filter, using the included M5 screws
(3), on the side of the filter opposite the release latch (6).
4. Mount the filter with customer-supplied fasteners (7).
5. Note the orientation of the flow indicator (5) on the top of the filter. Cut
10-mm blue air tubing to the required lengths to connect the air supply
to the filter and the filter to the controller, then connect the tubing.
E 2016 Nordson Corporation
Part 1604857-11
3-14 System Setup
3
FROM SUPPLY
4
5
1
7
2
6
2
1
Figure 3-14
TO CONTROLLER
Air Filter Installation − Wall and Rail Mount Systems
1. 10-mm air tubing (blue)
2. 10-mm tube x 1/2 male connectors
3. M5 screws
Part 1604857-11
4. Bracket
5. Flow indicator
6. Release latch
7. Customer-supplied fasteners
E 2016 Nordson Corporation
System Setup
3-15
System Electrical Connections
Power Supply
CAUTION: If you have a mobile system with a vibratory box feeder, check
the system identification plate for the correct voltage. Connecting a system
with a 115 Vac vibrator motor to 220 Vac could damage the vibrator motor.
The spray gun controller is rated for 100−240 Vac at 50/60 Hz, single phase,
and is marked as such, but the power supplied to the system must match
the vibrator motor rating.
Wire the system power cord to a customer-supplied three-prong plug.
Connect the plug to a receptacle that supplies the correct voltage.
Wire Color
Function
Blue
N (neutral)
Brown
L (hot)
Green/Yellow
GND (ground)
System Ground
Mobile Systems: See Figure 3-15. Connect the ground cable attached to
the controller ground stud to a true earth ground.
Figure 3-15
System Ground Connection
Rail Mount Systems: Locate the ESD grounding block kit. Follow the kit
instructions to install the grounding block to the grounded spray booth base.
Connect the flat braided ground cable from the controller ground stud to the
grounding block.
E 2016 Nordson Corporation
Part 1604857-11
3-16 System Setup
Controller Configuration
Power Up Sequence
When power is applied to the system, the controller goes through the
following sequence:
1. All displays and LEDs light for 3 seconds.
2. The main control board configuration is displayed on the KV/A panel:
A: Auto (refer to troubleshooting to change the jumper if A is displayed)
H: Manual
3. The controller software and hardware version are displayed on the
KV/A panel in the form N.NN for 1 second.
NOTE: If the spray gun is triggered on during power-up or wake up from
disable, the trigger LED blinks at a fast rate. Release the trigger and repeat
the sleep/wake up cycle.
Entering Configuration Mode
To enter configuration mode, press and hold the Plus and Minus buttons on
the kV/uA panel while either turning on power or pressing the
Enable/Disable button (if the controller is already powered up). After 1
second all panels flash CF for 3 seconds. After 3 seconds the kV/A panel
displays F − 1 for function 1. The controller is now in configuration mode.
To save your settings and exit Configuration Mode, press the
Enable/Disable button.
Enable/Disable
Select Charge
Mode Settings
KV/A Setting/Display
KV/uA Selection
Control
Trigger LED
Flow-Rate Air
(Classic)
Powder Flow Rate
(Smart Flow)
Setting/Display
Smart Flow Mode
Indicator
Atomizing Air
(Classic)
Total Flow
(Smart Flow)
Setting/Display
Figure 3-16
Controller Interface
Part 1604857-11
E 2016 Nordson Corporation
System Setup
3-17
Function Settings
To change functions, press the Plus or Minus buttons on the kV/A panel.
To change function values press the Plus or Minus buttons on the Flow Air
panel.
Function No.
Name
Settings
Default
1
Gun Type
0 = Encore
0
2
Fluidizing
0 = Hopper, 1 = Box, 3 = Disable
0
3
Electrostatic Control
0 = Custom, 1 = Classic
0
4
Powder Flow Control
0 = Smart, 1 = Classic
0
5
Cable Length
0 = 6 meters, 1 = 12 meters, 2 = 18 meters
0
6
Vibratory Box Delay
on, 0−90 seconds
30
NOTE: Refer to the Operation section for explanations of the differences in
Electrostatic Control and Powder Flow Control modes.
Vibratory Box Feeder Settings
Continuous Operation
To set the vibrator motor to continuous operation, choose the “on” setting. In
this mode, the vibrator motor turns on when the gun is first triggered and
stays on until you press the Enable/Disable button or turn off system power.
Shut Off Delay
If you set a delay time, the vibrator motor turns on when the gun is triggered
and stays on for the delay time after the trigger is released. This setting is
designed to prevent chattering (rapid on/off cycling) of the vibrator motor
during production and extends the life of the motor. Adjust the delay as
required for your application.
Exiting Configuration Mode
To accept all function values and exit Configuration Mode, press the
Enable/Disable button. The controller can now be operated normally.
E 2016 Nordson Corporation
Part 1604857-11
3-18 System Setup
Part 1604857-11
E 2016 Nordson Corporation
Operation
4-1
Section 4
Operation
WARNING: Allow only qualified personnel to perform the following tasks.
Follow the safety instructions in this document and all other related
documentation.
WARNING: This equipment can be dangerous unless it is used accordance
with the rules laid down in this manual.
WARNING: All electrically conductive equipment in the spray area must be
grounded. Ungrounded or poorly grounded equipment can store an
electrostatic charge which can give personnel a severe shock or arc and
cause a fire or explosion.
European Union, ATEX, Special Conditions for Safe Use
1. The Encore LT Controllers and Mobile Powder Systems shall be used
over the ambient temperature range of +15_C to +40_C with the Encore
LT Powder Electrostatic Manual Applicators.
2. The Encore LT Manual Controller can be installed in a non-hazardous
area or in a hazardous area defined as a Zone 22.
3. Caution should be taken when cleaning plastic surfaces on the
controller. There is a potential for static electricity build up on these
components.
Controller Interface
See Figure 4-1. Use the controller interface to make spray settings and
monitor system operation. Refer to Setup for configuration settings.
Low Power Mode
Pressing the Enable/Disable button for three seconds puts the controller to
sleep (low power mode). The displays and LEDs turn off. To wake the
controller press the button again.
The system hibernates automatically if no activity is detected for
approximately 15 minutes. Pulling the gun trigger, pressing the purge
switch, or pressing a button on the controller interface wakes the controller.
E 2016 Nordson Corporation
Part 1604857-11
4-2
Operation
Trigger LED
Enable/Disable
Flow Air
(Classic)
Powder Flow Rate
(Smart Flow)
Select Charge
Mode Settings
Smart Flow
Mode Indicator
KV/A Panel
KV/A Display
Selection
Figure 4-1
Atomizing Air
(Classic)
Total Flow
(Smart Flow)
Controller Interface
Displays and LEDs
When the gun is triggered the Trigger LED lights. Actual kV/A
outputs are displayed. When the gun is not triggered the kV/A setpoints
are displayed.
When the controller is configured for Smart Flow mode, the Smart
Flow LED is lit.
The air flow displays always show the setpoints.
Electrostatic Settings
Electrostatic output can set in Select Charge mode, Custom mode, or
Classic mode. Custom or Classic mode is chosen when the controller is
configured. Set the electrostatic output depending on the shape and type of
product being coated and the type of powder used.
Select Charger Mode
The Select Charge modes are non-adjustable electrostatic settings. The
LEDs above the Select Charge mode buttons indicate the selected mode.
The electrostatic setpoints for the Select Charge Modes are:
Re-Coat
100 kV, 15 A
Metallics
50 kV, 50 A
Deep Recesses
100 kV, 60 A
NOTE: Pressing the + or − keys have no effect when a Select Charge
mode is selected.
Part 1604857-11
E 2016 Nordson Corporation
Operation
Re-Coat
Figure 4-2
4-3
Metallics Deep Recesses
Select Charge Modes
NOTE: If you press the STD/AFC selection button while using a Select
Charge mode, the controller switches to Classic or Custom mode.
Custom Electrostatic Mode
Custom Mode is the factory default electrostatic mode.
In Custom mode, both kV output and microampere A) output limits can be
adjusted independently. Both the kV and AFC LEDs light to indicate that the
controller is in this mode.
Use the View button
to toggle the display between kV and A. Press
the + or − buttons to select the desired setpoints. The longer a button is
pressed the faster the units change.
S The valid AFC range is 5−100 A
S The valid STD range is 0 or 25−100 kV
Encore Nano Feedback Control Mode (NFC)
NFC Mode controls the electrostatic lower-limit range output for both kV
and A. NFC allows the user to control both kV and A independently.
S The valid kV range is 0−25 (increments of 1 kV)
S The valid A range is 0−10 (increments of 0.1 A)
To configure the controller for the NFC function, set the Electrostatic Control
(Function 3) to the custom mode (Custom = 0).
See Function Settings on page 3−17 of the System Setup section.
mA NFC Range and Settings
NFC mode allows the user to adjust the A setting in increments of 0.1 A
below the value of 10.0 A. Adjusting A in NFC modes allows the user to
control the current when using powders that tend to charge hot, such as
metallics.
For example, the user can set the A settings from 12, 11, 10, 9.9, 9.8, 9.7,
….. through 0.1.
E 2016 Nordson Corporation
Part 1604857-11
4-4
Operation
Custom Electrostatic Mode
(contd)
kV NFC Range and Settings
NFC mode allows the user to adjust the kV setting in increments of 1 kV
below the value of 25 kV without changing the A setting.
For example, the user can set the kV settings from 25, 24, 23, 22, …..
through 0.
Classic Electrostatic Mode
Classic Mode is the optional electrostatic mode. The controller must be
configured to use this mode; refer to page 3-16 for configuration
instructions.
In Classic mode you can choose to control kV (STD) output or A (AFC)
output, but not both at the same time.
Classic Standard (STD) Mode
See Figure 4-3. Use the STD mode to set the no-load output voltage (kV).
to toggle between STD and AFC.
1. Press the STD/AFC button
The LEDs light to show which is selected. Select STD. The STD LED
will light.
2. Press the View button
to toggle the display between kV and A.
Press the + or − buttons to select the desired kV setpoint. The longer a
button is pressed the faster the units change.
The valid STD range is 0 or 25−100 kV.
Part 1604857-11
E 2016 Nordson Corporation
Operation
4-5
Classic Electrostatic Mode (contd)
Figure 4-3
kV/ A Display and STD/AFC Selection for Classic Mode
Classic AFC Mode
See Figure 4-3. Use the AFC mode to set A output limits. In AFC mode,
kV automatically defaults to 100 kV. When current output increases, kV
output and electrostatic charging decreases. The closer the gun comes to
the part, the greater the current draw.
1. Press the STD/AFC button to toggle between STD and AFC. The AFC
LED lights when AFC is selected.
2. Press the View button
to toggle the display between kV and A.
Select A, then press the + or − buttons to select the desired A
setpoint. The longer a button is pressed the faster the units change.
The valid AFC range is 5−100 A.
Powder Flow Settings
The controller varies the flow and atomizing air to a venturi-type powder
pump depending on the settings. Flow air controls the amount and velocity
of the powder; atomizing air dilutes the powder flow and increases the
velocity. Since the air flow values are continuously monitored and adjusted,
a slight high frequency pulsation in the air lines is normal.
Two modes of pump air control are available:
Smart Flow − This is the factory default mode. In this mode, you set Total
Flow and Flow Air %. If you decrease the flow air %, the flow air pressure
decreases, but the atomizing air pressure increases, so that the result is
that the powder velocity remains the same. The Smart Flow LED lights
when the controller is configured for Smart Flow mode.
Classic Flow − This is the traditional method of controlling powder flow and
velocity. In this mode you set flow and atomizing air separately and balance
them manually for optimum results. When the controller is configured for
Classic Flow mode, the Smart Flow LED is off.
E 2016 Nordson Corporation
Part 1604857-11
4-6
Operation
NOTE: Refer to page 3-16 for a list of the mode defaults and configuration
instructions.
Flow Air % or Flow Air
Total Flow or Atomizing Air
Figure 4-4
Flow Setting Panels
Smart Flow Mode Settings
sets the powder flow rate (Flow Air %).
sets the powder velocity (Total Flow).
Setting values for both are 0−99% of maximum output. Press the + and −
buttons to enter the desired setpoint. The longer a button is pressed the
faster the units change.
When making Smart Flow settings, set the Total Flow setpoint first to obtain
the desired pattern size and velocity, then set the Flow Air % setpoint for the
desired powder flow.
At 7 bar (100 psi) supply pressure:
Part 1604857-11
Total Flow
Setting %
Flow Air
Setting %
Flow Air Pressure
bar (psi)
Atomizing Air Pressure
bar (psi)
50
50
1.7 (25)
1.7 (25)
50
25
0.86 (12.5)
2.6 (37.5)
E 2016 Nordson Corporation
Operation
4-7
Smart Flow Mode Settings (contd)
In other words,
If Total Flow = 50%, Flow Air = 50%, then
Flow air = 1.7 bar (25 psi) or 1/2 of 3.4 bar (50 psi), and
Atomizing air = 1.7 bar (25 psi) or 1/2 of 3.4 bar (50 psi).
If Total Flow = 50%, Flow Air = 25%, then
Flow air = 0.86 bar (12.5) psi or 1/4 of 3.4 bar (50 psi), and
Atomizing air = 2.6 bar (37.5 psi) or 3/4 of 3.4 bar (50 psi).
NOTE: If either Total Flow or Flow Air % are set to 0% then the controller
will not output any air when triggered and no powder will be pumped.
Powder velocity is inversely related to transfer efficiency; the higher the
velocity the lower the transfer efficiency. High powder flow rates can result
in faster wear of powder contact parts.
Use this chart as a starting point making changes for powder volume or
delivery velocity as required. The data in this table was collected using 20
feet of 11mm ID powder tubing and a typical white epoxy powder. For
higher output use 12.7mm ID powder tubing. Powder output values in g/min
are typical, your results may vary.
Total Air Setting % "
Flow Output Setting % B
20
40
60
80
100
20
45
79
118
168
168
40
60
80
Powder Output in g/min.
26
20
27
128
105
138
176
215
220
240
288
300
284
375
408
100
45
100
235
318
430
Classic Flow Mode Settings
To use Classic Flow mode, the controller must be configured for it. Refer to
page 3-16 for a list of the mode defaults and configuration instructions.
sets the flow air pressure
sets the atomizing air pressure.
Setting values for both are 0−99% of maximum air pressure. Press the +
and − buttons to enter the desired setpoint. The longer a button is pressed
the faster the units change.
At 7 bar (100 psi) supply pressure:
E 2016 Nordson Corporation
Flow
Setting %
Atomizing
Setting %
Flow Air Pressure
bar (psi)
Atomizing Air Pressure
bar (psi)
25
25
1.7 (25)
1.7 (25)
40
10
2.7 (40)
0.689 (10)
Part 1604857-11
4-8
Operation
In other words,
If Flow air = 25%, Atomizing air = 25%, then
Flow air = 1.7 bar (25 psi), Atomizing air = 1.7 bar (25 psi).
If Flow air = 40%, Atomizing = 10%, then
Flow air = 2.7 bar (40 psi), Atomizing air = 0.689 bar (10 psi).
Refer to your pump manual for typical operating values for Flow and
Atomizing air.
Spray Gun Operation
To spray powder, pull the spray trigger.
To purge the spray gun, release the spray trigger and press down on the
purge trigger. If using a vibratory box feeder, fluidizing air is shut off while
the gun is being purged. P is displayed on the flow display.
Purge
Trigger
Spray
Trigger
Figure 4-5
Gun Controls
Electrode Air Wash Operation
Electrode air wash air continually washes the spray gun electrode to
prevent powder from collecting on it. Electrode air wash air is turned on and
off automatically when the spray gun is triggered on and off.
Daily Operation
Startup
1. Turn on the spray booth exhaust fan.
2. Turn on the system air supply and power.
3. Install a box of powder or a hopper filled with powder on the cart.
S Box: Lower the pickup tube into the powder, wrap the plastic bag
around the pickup tube and secure it with a tie wrap.
S Hopper: Connect the hopper ground cable and fluidizing air. Install
the pump on the pickup tube or connect the air tubing to the pump.
4. Make sure the spray gun is not triggered, then turn on controller power.
The displays and icons on the controller interface should light.
Part 1604857-11
E 2016 Nordson Corporation
Operation
4-9
Startup (contd)
NOTE: If the spray gun is triggered on when the controller is powered up, a
fault will occur and the Trigger LED will blink fast. To clear the fault, release
the trigger and press the Disable/Enable button to put the controller to
sleep, then press the button again to wake it up.
5. Point the spray gun into the booth and press the trigger to start spraying
powder.
6. Adjust fluidizing air pressure if necessary, using the needle valve on the
rear panel of the controller:
S Box Feeder: Fluidizing air only turns on when the gun is triggered.
The air flow should just fluidize the powder around the pickup tube.
The powder should not boil violently or fountain out of the box.
S Feed Hopper: Fluidizing air is on continuously as long as the
controller is on. The powder should boil gently, without any fountains.
7. Adjust the controller to achieve the desired spray pattern and powder
flow rate.
The controller interface displays actual kV or A output when the gun is
spraying and setpoints when the gun is off. The air flow displays always
show the setpoints.
On Initial Startup: With the gun triggered, air set to zero, and no parts in
front of the gun, record the A output for each gun in the system. Monitor
the A output daily, under the same conditions. A significant increase in A
output indicates a probable short in the gun resistor. A significant decrease
indicates a resistor or voltage multiplier requiring service.
Purging
When purge air is turned on, the electrostatic voltage and pump air is turned
off and P appears on the flow display.
Purge the gun periodically to keep the powder path inside the spray gun
clean. The purge length and frequency needed depend on the application
and powder.
NOTE: The purge air only cleans the spray gun powder path. To purge the
powder hose, disconnect it from the pump and the gun, place the gun end
inside the booth, and blow it out from the pump end with compressed air.
E 2016 Nordson Corporation
Part 1604857-11
4-10 Operation
Powder Box Installation
NOTE: The vibrator table can hold a maximum 25 kg (50 lb) box of powder.
1. See Figure 4-6. Lift the pickup tube up and swing the tube bracket down
and under the pickup tube end to hold it in place on the arm.
Pickup Tube Arm
Pickup Tube
Tube Bracket
Figure 4-6
Pickup Tube Bracket Use
2. Place a box of powder on the vibrator table.
3. Fold back the box flaps and open the plastic bag containing the powder
coating. Fold the bag over the box flaps to keep the flaps out of the way.
NOTE: Do not force the end of the pickup tube into the powder. Vibration
and gravity will cause the pickup tube to sink into the powder.
4. Swing the tube bracket out from under the pickup tube and slide the
tube down into the powder.
5. To prevent accidental powder spills, wrap the plastic bag around the
pickup tube and loosely secure the bag with a tie wrap.
Vibratory Box Feeder Operation
When the controller is configured for a vibratory feed system, the vibratory
box feeder relay control is enabled. The relay turns on the vibrator motor
when the spray gun is triggered.
When the spray gun is triggered off, the vibrator motor remains on for a
configurable delay. This delay prevents rapid on/off motor cycling every time
you trigger the gun off and on and prolongs the life of the motor. The default
delay time is 30 seconds.
The vibrator motor can also be set to continuous operation. If set this way,
press and release the spray gun trigger to start the motor. To turn off the
motor, press the Enable/Disable button or turn off controller power.
To configure the system for a vibratory box feeder, change the VBF delay
time, or set the vibrator motor to continuous operation, refer to page 3-16.
Part 1604857-11
E 2016 Nordson Corporation
Operation
4-11
Changing Flat Spray Nozzles
WARNING: Release the spray gun trigger, put the controller to sleep, and
ground the electrode before performing this procedure. Failure to observe
this warning could result in a severe electrical shock.
NOTE: The tapered electrode holder of the electrode assembly has been
designed for optimized cleaning during color changes on systems using flat
spray nozzles. This tapered electrode holder will not accept conical
deflectors.
1. Purge the spray gun and press the Enable/Disable button to put the
controller to sleep in order to prevent accidental gun triggering.
2. See Figure 4-7. Unscrew the nozzle nut counterclockwise.
3. Pull the flat spray nozzle off the electrode assembly.
NOTE: Re-install the electrode assembly if it comes out of the powder
outlet tube.
4. Install a new nozzle on the electrode assembly. The nozzle is keyed to
the electrode assembly. Do not bend the antenna wire.
5. Screw the nozzle nut onto the gun body clockwise until finger-tight.
6. Press the Enable/Disable button to wake up the controller.
NOTE: To clean nozzles, use the Recommended Cleaning Procedure for
Powder Contact Parts on page 4-14.
Nozzle Nut
Figure 4-7
Flat Spray Nozzle
Electrode Assembly
Changing a Flat Spray Nozzle
E 2016 Nordson Corporation
Part 1604857-11
4-12 Operation
Changing Conical Nozzles and Deflectors
WARNING: Release the spray gun trigger, put the controller to sleep, and
ground the electrode before performing this procedure. Failure to observe
this warning could result in a severe electrical shock.
NOTE: The electrode assembly shipped with the gun is fitted with a
tapered electrode holder that will not accept a conical deflector and must be
changed prior to using the conical nozzle and deflector. Follow the
instructions in the conical nozzle kit shipped with the gun for this conversion.
1. Purge the spray gun and press the Enable/Disable button to put the
controller to sleep in order to prevent accidental gun triggering.
2. See Figure 4-8. Gently pull the deflector off the electrode assembly. If
only changing the deflector, install the new one on the electrode
assembly, being careful not to bend the electrode wire.
3. To change the entire nozzle, unscrew the nozzle nut counterclockwise.
4. Pull the conical nozzle off the electrode assembly.
NOTE: Re-install the electrode assembly if it comes out of the powder
outlet tube.
5. Install a new conical nozzle on the electrode assembly. The nozzle is
keyed to the electrode assembly.
6. Screw the nozzle nut onto the gun body clockwise until finger-tight.
7. Install a new deflector on the electrode assembly. Do not bend the
electrode wire.
8. Press the Enable/Disable button to wake up the controller.
NOTE: To clean nozzles, use the Recommended Cleaning Procedure for
Powder Contact Parts on page 4-14.
Conical Electrode Holder
Deflector
Figure 4-8
Nozzle Nut
Electrode
Assembly
Nozzle
Changing a Conical Nozzle
Part 1604857-11
E 2016 Nordson Corporation
Operation
4-13
Installing the Optional Pattern Adjuster Kit
An optional pattern adjuster kit with integral conical nozzle can be installed
in place of a standard flat spray or conical nozzle.
NOTE: Deflectors are not included with the pattern adjuster kit; they must
be ordered separately. The 38-mm deflector cannot be used with the kit.
1. Remove the deflector, nozzle nut, and conical nozzle, or the nozzle nut
and flat spray nozzle.
2. Blow off the electrode assembly.
3. See Figure 4-9. Install the integral conical nozzle onto the electrode
assembly and screw the nozzle nut clockwise until finger-tight
4. Install a 16, 19, or 26-mm deflector onto the electrode holder.
NOTE: To clean the pattern adjuster, use the Recommended Cleaning
Procedure for Powder Contact Parts on page 4-14.
Electrode
Assembly
Figure 4-9
Electrode Holder
Pattern
Adjuster Kit
Deflector
Pattern Adjuster Kit Installation
Shutdown
1. Purge the spray gun by pressing the Purge button until no more powder
is blown from the gun.
2. Press the Enable/Disable button to turn off the spray gun and put the
controller to sleep.
3. Turn off the system air supply and relieve the system air pressure.
4. If shutting down for the night or a longer period of time, disconnect
power to the controller.
5. Perform the Daily Maintenance procedures on page 4-14.
E 2016 Nordson Corporation
Part 1604857-11
4-14 Operation
Maintenance
WARNING: Allow only qualified personnel to perform the following tasks.
Follow the safety instructions in this document and all other related
documentation.
WARNING: Before performing the following tasks, turn off the controller
and disconnect system power. Relieve system air pressure and disconnect
the system from its input air supply. Failure to observe this warning may
result in personal injury.
Recommended Cleaning Procedure for Powder Contact Parts
Nordson Corporation recommends using an ultrasonic cleaning machine
and Oakiter BetaSolv emulsion cleaner to clean spray gun nozzles and
powder path parts.
NOTE: Do not immerse the electrode assembly in solvent. It cannot be
disassembled; cleaning solution and rinse water will remain inside the
assembly.
1. Fill an ultrasonic cleaner with BetaSolv or an equivalent emulsion
cleaning solution at room temperature. Do not heat the cleaning
solution.
2. Remove the parts to be cleaned from the gun. Remove the O-rings.
Blow off the parts with low-pressure compressed air.
NOTE: Do not allow the O-rings to come in contact with the cleaning
solution.
3. Place the parts in the ultrasonic cleaner and run the cleaner until all
parts are clean and free of impact fusion.
4. Rinse all parts in clean water and dry before re-assembling the spray
gun. Inspect the O-rings and replace any that are damaged.
NOTE: Do not use sharp or hard tools that will scratch or gouge the smooth
surfaces of powder contact parts. Scratches will cause impact fusion.
Part 1604857-11
E 2016 Nordson Corporation
Operation
4-15
Maintenance
Perform the Shutdown procedure before performing these procedures.
Component
Pump
(Daily)
Procedure
1. Disconnect the pump air hoses and remove the pump from the pickup tube.
2. Disassemble the pump and clean all parts using low-pressure compressed air. If
impact fusion is present on the parts, use the Recommended Cleaning Procedure
for Powder Contact Parts to remove it.
3. Replace any worn or damaged parts.
Refer to the Encore Powder Pump manual for instructions and spare parts.
Spray Gun
(Daily)
1. Point the spray gun into the booth and purge the spray gun.
2. Shut off the system air supply and power.
3. Disconnect the powder hose adapter and blow out the spray gun powder path.
4. Disconnect the powder hose at the pump. Place the gun end of the hose inside the
booth and blow out the hose from the pump end.
5. Remove the nozzle and electrode assembly and clean them with low-pressure
compressed air and clean cloths. If impact fusion is present on the nozzle parts,
clean them using the Recommended Cleaning Procedure for Powder Contact Parts
on page 4-14. Check the parts for wear and replace if necessary.
6. Clean the gun face surface (where the electrode assembly attaches) with low
pressure compressed air and a clean cloth.
7. Blow off the gun and wipe it down with a clean cloth.
Vibratory Box
Feeder Pickup
Tube
(Daily)
Disconnect the fluidizing air tubing. Pull the pickup tube out of the powder box and move
it into the booth. Blow powder off all outer and inner surfaces using low-pressure
compressed air.
Controller
(Daily)
Blow off the cart and controller with a blow gun. Wipe powder off the controller with a
clean cloth.
System Air
Filter
(Periodically)
Check the system air filter. Drain the filter and change the filter element as needed.
Refer to Parts for the replacement filter element part number.
System
Grounds
Daily: Make sure the system is securely connected to a true earth ground before
spraying powder.
Periodically: Check all system ground connections.
E 2016 Nordson Corporation
Part 1604857-11
4-16 Operation
Part 1604857-11
E 2016 Nordson Corporation
Troubleshooting
5-1
Section 5
Troubleshooting
WARNING: Allow only qualified personnel to perform the following tasks.
Follow the safety instructions in this document and all other related
documentation.
WARNING: Before making repairs to the controller or spray gun, shut off
system power and disconnect the power cord. Shut off the compressed air
supply to the system and relieve the system pressure. Failure to observe
this warning could result in personal injury.
These troubleshooting procedures cover only the most common problems.
If you cannot solve a problem with the information given here, contact your
contact Nordson technical support at (800) 433−9319 or your local Nordson
representative for help.
Controller Faults
Problem
1.
2.
Trigger LED blinks,
gun does not spray
KV/mA display blinks,
no KV when gun is
triggered
E 2016 Nordson Corporation
Possible Cause
Corrective Action
Gun was triggered on when the
controller was powered up or
woken up
Release the trigger. Press the
Enable/Disable button to put the
controller to sleep, then press the
button again to wake it up.
Shorted trigger switch or cable
Check the gun cable and trigger
switch.
Gun is shorted
Check gun cable, cable extension,
and gun power supply.
Part 1604857-11
5-2
Troubleshooting
General Troubleshooting Chart
Problem
1.
Uneven pattern,
unsteady or
inadequate powder
flow
Possible Cause
Blockage in spray gun, powder
hose, or pump
Corrective Action
1. Purge the spray gun. Remove
and clean the nozzle and
electrode assembly.
2. Disconnect the powder hose from
the spray gun. Blow out the spray
gun with an air gun.
3. Disconnect the powder hose from
the pump and gun and blow out
the hose. Replace the hose if it is
clogged with powder.
4. Disassemble and clean the pump.
5. Disassemble the spray gun.
Remove and clean the inlet and
outlet tubes and elbow. Replace
components as necessary.
2.
Voids in powder
pattern
Nozzle, deflector, or electrode
assembly worn, affecting pattern
Remove and clean the nozzle,
deflector, and electrode assembly.
Replace worn parts as necessary.
If excessive wear or impact fusion is
a problem, reduce the flow and
atomizing air.
Damp powder
Check the powder supply, air filters,
and dryer. Replace the powder
supply if contaminated.
Low atomizing or flow air pressure
Increase the atomizing and/or flow air
flow.
Improper fluidization of powder in
hopper
Increase the fluidizing air pressure.
If the problem persists, remove the
powder from the hopper. Clean or
replace the fluidizing plate if
contaminated.
Worn nozzle or deflector
Remove and inspect the nozzle or
deflector. Replace worn parts.
Plugged electrode assembly or
powder path
Remove and clean the electrode
assembly. Remove and clean the
spray gun powder path (inlet tube,
elbow, and outlet tube) if necessary.
Continued...
Part 1604857-11
E 2016 Nordson Corporation
Troubleshooting
Problem
3.
4.
5.
6.
7.
Loss of wrap, poor
transfer efficiency
No kV output from the
spray gun (kV=0),
powder is spraying
No kV output from the
spray gun (mA=0),
powder is spraying
No kV output and no
powder output
Powder build up on
the electrode tip
Possible Cause
5-3
Corrective Action
Low electrostatic voltage
Increase the electrostatic voltage.
Poor electrode connection
Remove the nozzle and electrode
assembly. Clean the electrode and
check for carbon tracking or damage.
Check the electrode resistance as
shown on page 5-6. If the electrode
assembly is good, remove the gun
power supply and check its
resistance as shown on page 5-6.
Poorly grounded parts
Check the conveyor chain, rollers,
and part hangers for powder buildup.
The resistance between the parts
and ground must be 1 megohm or
less. For best results, 500 ohms or
less is recommended.
Damaged gun cable
Perform the Gun Cable Continuity
Checks on page 5-7.
If an open or short is found, replace
the cable.
Spray gun power supply shorted
Perform the Power Supply
Resistance Test on page 5-6.
Spray gun power supply open
Perform the Power Supply
Resistance Test on page 5-6.
Damaged gun cable
Perform the Gun Cable Continuity
Test on page 5-7.
If an open or short is found, replace
the cable.
Malfunctioning trigger switch or
cable
Check the trigger LED on the
controller interface. If the LED is not
lit, check the switch connection to the
gun cable.
Perform the Gun Cable Continuity
Test on page 5-7. If the cable and
connections are good, replace the
switch.
Controller configured for automatic
operation
Cycle controller power. If A appears
on the kV/uA display, remove the
main control board and move the JP1
jumper to the Manual position.
Insufficient electrode air wash flow
due to low input pressure or
blockage in manifold orifice
Check input air pressure. Remove
electrode air wash connector and
check manifold orifice for blockage.
Orifice size is .25−.3 mm. Clean with
an appropriate tool.
Continued...
E 2016 Nordson Corporation
Part 1604857-11
5-4
Troubleshooting
Problem
Possible Cause
Corrective Action
8.
No purge air when
gun purge switch is
pressed down
Malfunctioning spray gun trigger
switch or cable, or controller
manifold purge solenoid valve; no
air pressure, or kinked air tubing
If the controller interface does not
display P when the purge switch is
pressed, the gun trigger switch may
be defective.
Perform the Gun Cable Continuity
Test on page 5-7. If the cable is
good, replace the trigger switch.
If the interface displays P when the
purge switch is pressed, check the
purge air tubing and purge manifold
solenoid valve.
9.
Low powder flow or
powder flow surging
Low supply air pressure
Input air must be greater than 4.1 bar
(60 psi).
Supply air filter plugged or filter
bowl full—water contamination of
controller
Remove the filter bowl and drain
water/dirt. Replace the filter element
if necessary. Clean the system,
replace components as necessary.
Flow air valve plugged
Remove the valve and check the
manifold passages. If the manifold is
clean, replace the valve.
Air tubing kinked or plugged
Check the flow and atomizing air
tubing for kinks.
Pump throat worn
Replace the pump throat.
Pump not assembled correctly
Check the pump.
Pick-up tube blocked
Check for debris or bag (VBF units)
blocking pick-up tube.
Vibratory box feeder disabled
(VBF units only)
Make sure sure the controller is
configured for a VBF system. Refer
to the Setup section.
Fluidizing air too high
If fluidizing air is set too high the ratio
of powder to air will be be too low.
Fluidizing air too low
If fluidizing air is set too low the pump
will not operate at peak efficiency.
Powder hose plugged or kinked
Check for kinks in hose, blow out with
compressed air.
Powder hose too long or diameter
too small
25-ft of 11-mm ID hose is shipped
with the system. If using a longer
hose, switch to 1/2 in. ID hose.
Shorten the hose if necessary.
Gun powder path plugged
Check the inlet tube, elbow, outlet
tube, and electrode support for
impact fusion or debris. Clean as
necessary with compressed air.
Flow and atomizing air tubing
connections reversed
Check flow and atomizing air tubing
routing and switch if incorrect.
Continued...
Part 1604857-11
E 2016 Nordson Corporation
Troubleshooting
Problem
5-5
Possible Cause
Corrective Action
10. Vibrator doesn’t turn
On and Off with the
gun trigger
Controller configured for a hopper
system
Make sure sure controller is
configured for a VBF system. Refer
to Configuration in the Setup section.
11. VBF system−
fluidizing air is on
when the gun is
triggered Off
Controller configured for a hopper
system
Make sure sure controller is
configured for a VBF system. Refer
to Configuration in the Setup section.
12. No KV when gun is
triggered On, powder
flow OK
KV set to zero
Set KV to a non-zero value.
13. No powder flow when
gun is triggered On,
kV OK
Flow Air or Total Flow set to zero
Change settings to a non-zero
number.
Input air turned OFF
Make sure air is being supplied to the
controller.
Flex connection from the keypad
to the main board is not seated
properly
Loosen and re-seat the flex circuit on
the main board, making sure the flex
cable is fully inserted into the
connector.
To loosen the flex circuit, gently pull
the black bar on the cable connector
away from the white connector. This
will allow you to adjust the flex cable
to ensure proper seating. The cable
should be inserted past the white line
marked towards the end of the cable.
Push the black bar back into the
white connector to secure.
14. More than one key on
the keypad quits
working when
pressed
E 2016 Nordson Corporation
Part 1604857-11
5-6
Troubleshooting
Spray Gun Power Supply Resistance Test
Use a megohm meter to check the resistance of the power supply, from the
J2−3 feedback terminal at the connector to the contact pin inside the front
end. The resistance should be between 280−320 megohms. If the reading is
infinite, switch the meter probes. If the resistance falls outside this range,
replace the power supply.
280−320 Megohms at 500 VDC
J2−3 (YELLOW)
FEEDBACK
J2−1 (RED)
OSC
J2−2 (BLACK)
COMMON
Figure 5-10 Power Supply Resistance Test
Electrode Assembly Resistance Test
Use a megohm meter to measure the resistance of the electrode assembly
from the contact ring on the back to the antenna wire in the front. The
resistance should be 19−21 megohms. If the resistance is out of this range
replace the electrode assembly.
19−21 Megohms
Figure 5-11
Electrode Assembly Resistance Test
Part 1604857-11
E 2016 Nordson Corporation
5-7
Troubleshooting
Gun Cable Continuity Test
Test for continuity as follows:
S
S
S
S
S
S
J1
J1−1
J1−2
J1−3
J1−4
J1−5
J1−6
J1−1 and J3−2
J1−2 and J2−2, J3−5
J1−3 and J2−1
J1−4 and J3−4
J1−5 and J2−3
J1−6 and J3−3, ground terminal
PURGE
COMMON
OSC
TRIGGER
FEEDBACK
GND
CONTROLLER END
(FACE VIEW)
BLU
ORG
WHT
BLK
BLU
RED
WHT
ORG
N/C J3−1
TRIGGER
J3−4
+12V COM
J3−5
PURGE
J3−2
GND
J3−3
GRN
YEL
GRN
RED
BLK
YEL
OSC
J2−1
COMMON
J2−2
FEEDBACK
J2−3
BRAIDED SHIELD
GRN
J3
TO TRIGGER SWITCH
J2
TO POWER SUPPLY
CABLE GND
TO GUN GROUND STUD
J1 (FACE VIEW)
J3 (FACE VIEW)
J1−2
(BLACK
AND BLUE)
J1−1
(ORANGE)
J3−5
(BLUE)
J3−1
(N/C)
J1−3
(RED)
J3−2
(ORANGE)
J3−4
(WHITE)
J3−3
(GREEN)
J1−6
(GREEN)
J1−4
(WHITE)
J1−5
(YELLOW)
J2−3
(YELLOW)
J2−2
(BLACK)
J2−1
(RED)
J2 (FACE VIEW)
POWER SUPPLY CONNECTOR
Figure 5-12 Gun Cable Wiring
E 2016 Nordson Corporation
Part 1604857-11
5-8
Troubleshooting
Part 1604857-11
E 2016 Nordson Corporation
Repair
6-1
Section 6
Repair
WARNING: Allow only qualified personnel to perform the following tasks.
Follow the safety instructions in this document and all other related
documentation.
Spray Gun Repair
NOTE: All item numbers in the spray gun repair illustrations are the same
as the item numbers in the spray gun parts list.
Power Supply and Powder Path Replacement
Gun Disassembly
1. See Figure 6-1. Remove the nozzle nut, nozzle, and electrode assembly
(1, 2, 3).
2. Remove the screws (11, 12) and hook, cover, and housing (8, 9, 10).
3. Pull the power supply harness out of the bulkhead, then insert a small
flat-bladed screwdriver into the recess in the harness connector to
release the catch. Disconnect the gun cable from the power supply
harness.
11
1
2
3
12
Figure 6-1
8
9
10
Power Supply Connectors
Trigger Connectors
Gun Disassembly
1. Nozzle nut
2. Nozzle
3. Electrode assembly
E 2016 Nordson Corporation
8. Cover
9. Housing
10. Hook
11. M3 x 30 screw
12. M3 x 20 screw
Part 1604857-11
6-2
Repair
Gun Disassembly
(contd)
4. See Figure 6-2. Remove the black nylon screw (22) from the gun body.
5. Grasp the handle in one hand and the gun body in the other. Press the
thumbs of each hand together while pulling in opposite directions to
separate the gun body from the handle. The air wash tubing will prevent
a complete separation; leave it connected unless it must be replaced.
22
Figure 6-2
Removing the Gun Body from the Handle
Power Supply Replacement
NOTE: If replacing the powder path, skip this procedure.
1. Slide the power supply (5) out of the gun body.
2. Check the gasket (6) on the back of the bulkhead (7). Replace it if it is
damaged. The gasket is stuck to the bulkhead with pressure-sensitive
adhesive.
7
6
5
Figure 6-3
Removing the Power Supply from the Gun Body
3. Slide the new power supply into the upper cavity of the gun body,
guiding the gun body ribs between the raised grooves on the top of the
power supply.
Part 1604857-11
E 2016 Nordson Corporation
Repair
6-3
4. Press on the end of the power supply to ensure that the power supply
contact tip is firmly seated against the brass contact inside the gun body.
5. Route the power supply harness connector through the top hole in the
bulkhead.
Powder Path Replacement
NOTE: Skip these steps if not replacing the powder path. Go to page 6-4
to reassemble the spray gun.
1. See Figure 6-4. Remove the elbow (18) from the inlet tube (25).
2. Remove the two M3 x 20 screws (12) from the handle base (27). Pull
the base away from the handle, swing the bottom of the ground pad (15)
up and away from the handle, then remove it. Leave the ground wire
connected to the ground pad.
3. Push the inlet tube (25) up and out of the base, then move the base out
of the way and pull the inlet tube out of the handle.
4. Push the outlet tube (4) out of the front of the gun body (13).
5. Blow off the inlet tube, outlet tube, and elbow, and replace them if the
interiors are worn or coated with impact-fused powder. If re-using the
tubes, make sure the O-rings are undamaged.
13
4
14
18
15
24
25
14
15
27
12
Figure 6-4
Powder Path Replacement
4. Outlet tube
12. M3 x 20 screws
13. Gun body
E 2016 Nordson Corporation
14. Air wash tubing
15. Ground pad
18. Elbow
24. Handle
25. Inlet tube
27. Handle base
Part 1604857-11
6-4
Repair
Powder Path Installation
1. See Figure 6-4. Install the outlet tube (4) into the gun body (13), with the
end of the tube flush with the end of the gun.
2. Install the inlet tube (25) into the handle (24), then install the end of the
tube into the handle base (27).
3. Push the handle base close to the handle, then hook the top end of the
ground pad (15) into the body and rotate it onto the handle. Make sure
the cable wires are not pinched or trapped during re-assembly.
4. Install the handle base onto the handle and ground pad and secure it
with the two M3 x 20 screws (12).
5. Install the elbow onto the inlet tube, with the end oriented toward the
front of the gun as shown.
Gun Re-Assembly
1. See Figure 6-5. Align the gun body with the handle and slide them
together, engaging the internal ribs of the gun body with the handle tabs.
NOTE: Make sure that the power supply harness is not pinched between
the bulkhead and the power supply.
Elbow
Internal Ribs
Figure 6-5
Handle Tabs
Installing the Gun Body on the Handle
2. Insert your finger into the outlet tube at the front of the gun and align the
inside end of the tube with the elbow, then push on the tube to seat it in
the elbow.
3. Connect the power supply harness to the gun cable, then tuck both
through the bottom hole in the bulkhead, into the gun body.
4. See Figure 6-1. Install the cover, housing, and hook as as shown.
5. Install the electrode assembly (3) into the front of the gun body. Make
sure the wire electrode is not bent or broken.
6. Install the nozzle (2) on the electrode assembly, making sure the keys in
the electrode assembly slide into the slots on the nozzle.
7. Install the nozzle nut (1) over the nozzle and rotate clockwise to secure.
Part 1604857-11
E 2016 Nordson Corporation
Repair
6-5
Cable Replacement
Cable Removal
1. Disconnect the gun cable from the controller.
2. See Figure 6-1. Remove the bottom screw (12) from the housing (9).
3. See Figure 6-6, View A. Loosen the two M3 x 20 screws (12) securing
the handle base (27) to the handle.
4. Pull the base away from the handle enough to free the bottom edge of
the ground pad (15) from the base.
5. Pull the bottom edge of the ground pad out and away from the handle.
6. See Figure 6-6, View B. Remove the M3 x 8 screw, lock washer (16,
17), and ground terminal from the ground pad.
7. Remove the E-ring (30) from the cable.
8. See Figure 6-6, View C. Pull the cable connectors out of the handle.
Disconnect the power supply harness from the gun cable by inserting a
small flat-bladed screw driver in the slot of the power supply harness
connector to release the catch.
9. Carefully disconnect the round trigger connector from the trigger switch
connector.
10. Pull the cable out of the handle base, feeding the connectors through
the base one at a time.
15
15
12
27
Power Supply
Trigger
16
17
VIEW A
Ground
30
VIEW B
VIEW C
Figure 6-6
Cable Replacement
12. M3 x 20 screws
15. Ground pad
E 2016 Nordson Corporation
16. M3 x 6 screw
17. Lock washer
27. Handle base
30. E-ring
Part 1604857-11
6-6
Repair
Cable Installation
1. See Figure 6-6. Feed a new cable through the handle base, then install
the E-ring (30) on the cable to hold it in place.
2. Connect the cable to the trigger switch and power supply.
3. Connect the cable terminal to the ground pad (15) with the M3 x 6 screw
and lock washer (16, 17).
4. Tuck the cable connectors and ground wire into the gun, below the
multiplier.
5. Hook the top of the ground pad into the gun body, then rotate it into
position on the handle.
6. Push the handle base (27) up against the handle and ground pad, and
tighten securely the two M3 x 20 screws (12) in the base.
7. See Figure 6-1. Install the bottom M3 x 20 screw (12) in the housing (9)
and tighten it securely.
Trigger Switch Replacement
Switch Removal
1. See Figure 6-6. Remove the ground pad as described in Cable Removal
steps 1−5 . You do not have to disconnect the ground cable from the
ground pad.
2. Pull out the round trigger connectors out of the handle and disconnect
them.
3. See Figure 6-7. Place the spray gun on a solid surface so the small
diameter end of the trigger axle (20A) is oriented updward.
4. Using a small, flat-ended punch or Allen key, apply light downward
pressure to the small diameter end of the trigger axle (20A) and lightly
tap to remove.
5. Remove the spray trigger (20), actuator (21, not shown), and purge
trigger (19) from the handle.
Gusset
20
20A
19
19
20A
Figure 6-7 Removing the Axle and Trigger from the Handle
Part 1604857-11
E 2016 Nordson Corporation
Repair
6-7
6. See Figure 6-8. Insert a small flat-bladed screwdriver behind the clear
pull tab at the top of the switch, then grasp the pull tab with a finger and
gently pull it away from the handle.
Figure 6-8
Removing the Trigger Switch from the Handle
7. To remove the switch, cut the ribbon cable, or feed the bottom of the
switch through the slot in the trigger recess and remove it from the
handle.
Switch Installation
1. See Figure 6-9. Orient the new switch with the grid facing away from the
inlet tube, then carefully feed the square, bottom end of the switch (23)
around the left side of the inlet tube (25) and through the slot in the
trigger recess.
2. Peel off the small piece of tape holding the ribbon cable against switch.
Figure 6-9
Installing the Trigger Switch − Steps 1 and 2
3. See Figure 6-10. Straighten the ribbon cable, then bend the pull tab at
the top of the switch so that it is perpendicular to the switch.
Figure 6-10
E 2016 Nordson Corporation
Installing the Trigger Switch − Step 3
Part 1604857-11
6-8
Repair
Switch Installation (contd)
4. See Figure 6-11. Peel the adhesive release liner from the switch.
5. Carefully install the switch, pull tab up, against the bottom and right
edges of the trigger recess.
6. Make sure the ribbon cable is not trapped or pinched, then press the
switch against the back of the recess. Run your finger up and down on
the switch to ensure it is securely adhered to the handle.
Figure 6-11
Installing the Trigger Switch − Step 4
7. See Figure 6-12. Install the purge trigger (19) into the spray trigger (20)
with the gusset oriented upward as shown. Do not install the purge
trigger upside down.
8. Verify that the actuator (21) is installed over the post.
9. Position the triggers in the handle and hold them in place while pressing
the axle (20A) through the handle and triggers until the head of the axle
is flushed with the handle. The axle will snap into place when properly
installed.
Gusset
20A
19
20
21
20
19
Figure 6-12 Reinstalling the Trigger and Axle
10. Reconnect the trigger switch connector to the round cable connector,
then tuck the connectors back up to the handle.
11. Reinstall the ground cover as described in Cable Installation steps 5−7
on page 6-6.
Part 1604857-11
E 2016 Nordson Corporation
Repair
6-9
Controller Repair
WARNING: Shut off the controller and disconnect the power cord or
disconnect and lock out power at a breaker or disconnect ahead of the
controller before opening the controller enclosure. Failure to observe this
warning could result in a severe electrical shock and personal injury.
CAUTION: Electrostatic sensitive device. To avoid damaging the controller
circuit boards, wear a grounding wrist strap and use proper grounding
techniques when making repairs.
Front Panel Components
Refer to Section 5, Troubleshooting, for the controller electrical schematic
and harness connections. Refer to Section 7, Parts for repair kits.
3
2
1
Figure 6-13 Controller Front Panel
1. Bezel
E 2016 Nordson Corporation
2. Keypad
3. Main control board
Part 1604857-11
6-10 Repair
Rear Panel Components
Figure 6-14 is an exploded view of the components of the rear panel. Refer
to the following when making repairs:
S Section 7, Parts for parts and service kits.
S Section 5, Troubleshooting, for wiring diagrams and circuit board
connections.
NOTE: If replacing the relay board (2), JP1 must be jumped for a 115V
vibrator motor. For a 230V vibrator motor, remove the jumper.
1
2
J1
L2 F
L2
2
F2
L1 F
L1
F1
RL1
C1
M1 M2 M3
C2
Install jumper for 115V motor;
remove for 230V motor.
JP1
2
1
3
4
9
8
7
6
5
Figure 6-14 Sub Panel Parts Replacement
1. Manifold assembly
2. Relay board
3. Power supply
Part 1604857-11
4. Line filter
5. Fluidizing air solenoid valve
6. Purge air solenoid valve
7. Air wash air solenoid valve
8. Flow-rate air regulator
9. Atomizing air regulator
E 2016 Nordson Corporation
Repair
6-11
Vibrator Motor Replacement
When replacing the motor, make sure you order the correct motor for your
voltage. Vibrator motors include the power cable.
1. Remove the front panel from the dolly tower, then dismount the
controller.
2. Remove the screws securing the rear panel to the controller enclosure,
then carefully slide the rear panel out of the enclosure.
3. Disconnect the vibrator motor cable from the relay board, then loosen
the cord grip and pull the cable out of the panel.
4. Route the new motor cable through the cord grip, then connect the cable
leads to the relay board as shown below. Make sure the relay board
jumper is set for the correct voltage.
1
115V MOTOR
L1 F
JP1
Jumper JP1 for 115V Motor
Remove Jumper for 230V Motor
M1 M2 M3
(YEL/GRN)
C2
(RED)
RL1
C1
M1 M2 M3
(WHITE)
F1
(GREEN)
L1
230V MOTOR
M1 M2 M3
(BLUE)
ENCORE LT
RELAY PCA
F2
(BLACK)
L2
(BLACK)
J1
(BROWN)
2
L2 F
VBF POWER CORD WIRING
Figure 6-15 Vibrator Motor Connections
E 2016 Nordson Corporation
Part 1604857-11
6-12 Repair
Part 1604857-11
E 2016 Nordson Corporation
Parts
7-1
Section 7
Parts
Introduction
To order parts, call the Nordson Industrial Coating Systems Customer
Support Center at (800) 433-9319 or contact your local Nordson
representative.
This section covers parts for the Encore LT spray gun, controller, system
components and parts, powder and air tubing, and options.
Refer to the following manuals for additional information and optional
equipment.
Encore LT Manual System Operator Card: 1108213
Encore Generation II Powder Feed Pump: 1095927
Encore 150, 300, 450, and 600-mm Lance Extensions: 1606796
Pattern Adjuster Kit for Lance Extensions: 1100013
Pattern Adjuster Kit for Encore Manual Spray Guns: 10984490
These manuals can be downloaded from:
http://emanuals.nordson.com/finishing/
(click on Powder−US, then Encore Systems)
System Part Numbers
Use these part numbers to order complete systems.
Part
Description
1107897
SYSTEM, dolly with vibratory box feeder, 115 V, VBF, Encore LT
1107898
SYSTEM, dolly with vibratory box feeder, 220 V, VBF, Encore LT
1107901
SYSTEM, dolly with hopper, 50 lb, Encore LT
1108212
SYSTEM, rail mount, Encore LT
1609080
SYSTEM, rail mount, Encore LT, inline
1600438
SYSTEM, wall mount, Encore LT
1609081
SYSTEM, wall mount, Encore LT, inline
Note
Spray Gun Parts
See Figure 7-1 and the parts list on the following pages.
E 2016 Nordson Corporation
Part 1604857-11
7-2
Parts
Spray Gun Parts Illustration
32
32A
33
34
5
4
4A
3
3A
3B
9
2
31
11
10
8
7
1
12
6
13
14
15
16
17
18
20A
19
23
22
20
21
30
24
25B
26A
25
26
26B
25A
35
35A
29
27
28
Figure 7-1
12
Exploded View of Encore LT Manual Spray Gun and Accessories
Part 1604857-11
E 2016 Nordson Corporation
Parts
7-3
Spray Gun Parts List
See Figure 7-1.
Item
Part
Description
Quantity
Note
−
1106893
HANDGUN assembly, Encore LT
1
1
1081638
S NUT, nozzle, handgun
1
2
1081658
S NOZZLE, flat spray, 4 mm
1
A
F
3
1604824
S ELECTRODE ASSEMBLY, Encore, flat spray
1
3A
1106078
S S ELECTRODE, spring contact
1
3B
1605863
S S HOLDER, electrode, M3, flat spray, Encore
1
F
4
1085024
S KIT, powder outlet tube, Encore
1
D
4A
941113
S S O-RING, silicone, 0.438 x 0.625 x 0.094 in.
1
5
1081785
S S O-RING, silicone, 0.468 x 0.568 x 0.05 in.
1
6
1088502
S GASKET, multiplier cover, handgun
1
7
1106872
S BULKHEAD, multiplier, handgun, Encore LT/XT
1
8
1087559
S COVER, housing, Encore
1
9
1087558
S HOUSING, gun, Encore
1
10
1087760
S HOOK, handgun
1
11
1078075
S SCREW, pan head, recessed, M3 x 30, zinc
1
12
760580
S SCREW, Philips head, M3 x 20, zinc
3
13
1608280
S KIT, negative power supply/manual body,
Encore
1
14
1088558
S S FILTER ASSEMBLY, handgun
1
15
1106871
S HANDLE, ground pad, handgun, Encore LT/XT
1
16
983520
S WASHER, lock, internal, M3, zinc
1
17
982427
S MACHINE SCREW, pan head, recessed,
M3 x 6, zinc
1
18
1096695
S ELBOW, powder tube, handgun
1
19
1081540
S TRIGGER, purge, setting, handgun
1
20
1606999
S KIT, trigger w\ axle, Encore
1
20A
−−−−−
S S AXLE, trigger, solid, spray gun, Encore
1
21
1106892
S S ACTUATOR, switch, trigger, Encore LT/XT
1
22
1088601
S SCREW, flat head, recess, M5x 10, nylon
1
23
1108095
S KIT, trigger switch, Encore LT
1
24
1106870
S HANDLE, handgun, Encore LT/XT
1
25
1085026
S KIT, powder inlet tube, Encore
1
25A
1084773
S S O-RING, silicone, 18 mm ID x 2 mm wide
2
25B
1081785
S S O-RING, silicone, 0.468 x 0.568 x 0.05 in.
1
26
1106756
S CABLE ASSEMBLY, spray gun, manual,
Encore LT, 6 meter
1
26A
26B
940129
1604500
S S O-RING, silicone, conductive, 0.375 x 0.50in.
S S CLAMP, cable, 0.25 ID x 0.05 thick, white
1
1
27
1087762
S BASE, handle, handgun
1
28
1081617
S CHECK VALVE, male, M5 x 6 mm
1
29
1081616
S FITTING, bulkhead, barb, dual, 10−32 x 4 mm
1
30
1081777
S RETAINING RING, external, 10 mm
1
31
1604828
S KIT, conical nozzle, Encore
32
1083206
S S DEFLECTOR ASSEMBLY, conical, 26 mm
E 2016 Nordson Corporation
1
G
D
E
A
Part 1604857-11
7-4
Parts
Item
Part
Description
Quantity
Note
32A
1098306
S S S O-RING, Viton, 3 mm x 1.1 mm wide
1
B
33
1082060
S S NOZZLE, conical
1
A
34
1605861
S S HOLDER, electrode, M3, conical, Encore
1
1
35
1106200
S KIT, hose adapter, hose, handgun, Encore
35A
940157
S S O-RING, Viton, black, 0.563 x 0.688, 10415
NS
900617
S TUBE, polyurethane, 4 mm OD, clear
AR
C
NS
900741
S TUBING, polyurethane, 6/4 mm, black
AR
C
NS
900620
S TUBING, poly, spiral cut, 3/8 in. ID
AR
C
2
NOTE A: 4-mm flat spray nozzle, conical nozzle and 26 mm deflector are shipped with the spray gun. Refer to the
following pages for optional nozzles.
B: This O-ring is a component of all deflectors.
C: Order in increments of one foot or one meter.
D: Also available in wear resistant material. Refer to Spray Gun Options.
E: Optional 6 meter extension available, refer to Spray Gun Options.
F: For flat spray nozzle use only. Use kit item 31 to convert for conical nozzle and deflector use.
G: Application Specific: Order part number 1609053 if a positive power supply is needed. The positive
power supply is sold separately from the gun body (1088506).
AR: As Required
NS: Not Shown
Spray Gun Options
Miscellaneous Spray Gun Options
See Figure 7-1.
Item
4
Part
1096698
Description
Quantity
KIT, powder outlet tube, wear resistant
1
4A
941113
S O-RING, silicone, 0.438 x 0.625 x 0.094 in.
1
4B
1081785
S O-RING, silicone, 0.468 x 0.568 x 0.05 in.
1
18
1096696
ELBOW, powder tube, Encore, impact resistant
1
NS
1100012
KIT, pattern adjuster, Encore lance extensions
1
NS
1085168
1
NS
1100777
CABLE, 6 meter extension, shielded, Encore
manual
KIT, cup gun, Encore
1
Note
A
B
NOTE A: This pattern adjuster kit is only for use with a lance extension. See page 7-8 for the standard pattern
adjuster kit.
B: Refer to the instruction sheet 1102764 shipped with the kit for instructions.
NS: Not Shown
Part 1604857-11
E 2016 Nordson Corporation
Parts
7-5
Flat Spray Nozzles
The 4-mm flat spray nozzle is shipped with the spray gun. All other flat
spray nozzles are optional.
Figure 7-2
1081656
2.5 mm Flat Spray
1081657
3 mm Flat Spray
1081658
4 mm Flat Spray
1081659
6 mm Flat Spray
Flat Spray Nozzles
Cross-Cut Nozzles
1082184
60 Degree Cross-cut
Figure 7-3
1082185
90 Degree Cross-cut
1082186
2.5 mm Castle
Cross-cut Nozzles
E 2016 Nordson Corporation
Part 1604857-11
7-6
Parts
45-Degree Corner-Spray Nozzle
See Figure 7-4.
Spray Pattern
Wide fan pattern perpendicular to the spray gun axis
Slot Type
Angled, cross slot
Application
Flanges and recesses
Part
Description
1102872
Figure 7-4
Note
NOZZLE, corner spray, Encore
45-Degree Corner Spray Nozzle
45-Degree In-Line Flat-Spray Nozzle
See Figure 7-5.
Spray Pattern
Narrow fan pattern in-line with spray gun axis
Slot Type
Three angled slots in-line with spray gun axis
Application
Top and bottom coating; typically no in/out part positioning
Part
Description
1102871
Figure 7-5
Note
NOZZLE, 45 degree, flat spray, Encore
45-Degree Flat Spray Nozzle
Part 1604857-11
E 2016 Nordson Corporation
Parts
7-7
Conical Nozzle, Deflectors and Electrode Assembly Parts
See Figures 7-6, 7-7, and 7-8. The conical nozzle and deflectors must be
used with the conical electrode holder. A conical nozzle kit is shipped with
the gun. All other parts are optional and must be ordered separately.
Conical Nozzle and Deflectors
1082060
Conical Nozzle
1083201
16-mm Deflector
1083205
19-mm Deflector
1083206
26-mm Deflector
1083207
38-mm Deflector
All deflectors include a 1098306 O-ring, Viton, 3 mm x 1.1 mm wide
Figure 7-6
Conical Nozzle and Deflectors
Conical Nozzle Kit
1
Figure 7-7
2
3
Conical Nozzle Kit
Item
Part
Description
Quantity
—
1604828
KIT, conical nozzle, Encore
1
1
1083206
S DEFLECTOR, 26 mm
1
2
1082060
3
1605861
S NOZZLE, conical
S ELECTRODE HOLDER, Conical
1
Note
1
Conical Electrode Assembly
1
2
3
Figure 7-8
Conical Electrode Assembly
Item
—
Part
Description
Quantity
1106076
ELECTRODE ASSEMBLY, conical, Encore
1
1
−−−−−−
S ELECTRODE SUPPORT
1
2
1106078
1605861
S ELECTRODE
S ELECTRODE HOLDER, Conical
1
3
E 2016 Nordson Corporation
Note
1
Part 1604857-11
7-8
Parts
Pattern Adjuster Kit
The pattern adjuster kit includes an integral conical nozzle. 16, 19, and
26-mm deflectors can be used with the kit. The deflectors are not included
with the kit; they must be ordered separately.
1098417
Kit, Pattern Adjuster, Manual Gun, Encore
Figure 7-9
Pattern Adjuster Kit
Lance Extensions
The nozzles listed on the preceding pages install directly on the lance
extensions. Refer to the instruction sheet shipped with the lance extensions
for installation instructions and repair parts.
Part
Description
1609888
EXTENSION, lance, 150 mm, Encore
1609889
EXTENSION, lance, 300 mm, Encore
1609896
EXTENSION, lance, 450 mm, Encore
1609897
EXTENSION, lance, 600 mm, Encore
Note
NOTE: The electrode support/holder for use with conical nozzles and
deflectors must be used with a lance extension.
Pattern Adjuster Kit for Lance Extensions
Use this pattern adjuster with the lance extensions listed above and 16, 19,
and 26-mm conical nozzle deflectors listed on the preceding pages. Refer
to the instruction sheet shipped with the pattern adjuster for installation
instructions and repair parts.
Part
1100012
Part 1604857-11
Description
Note
KIT, pattern adjuster, Encore lance extension.
E 2016 Nordson Corporation
Parts
7-9
Ion Collector Kit
This kit installs on the standard length gun. Refer to the instruction sheet
shipped with the spray gun for installation instructions and repair parts.
Item
—
Part
1603854
Description
KIT, ion collector assembly, manual, Encore (std
length gun)
Quantity
Note
1
Ion Collector Components for Lance Extensions
To use the ion collector kit listed above with 150-mm or 300-mm Lance
Extensions, order one of the rods and the bracket listed below. Refer to the
instruction sheet shipped with the kit for installation instructions.
Item
Part
Description
Quantity
Note
—
189483
ROD, ion collector, 15 in.
1
A
—
189484
ROD, ion collector, 21 in.
1
B
—
1603939
BRACKET, lance extension, ion collector, Encore
1
A, B
NOTE A: Use for 150-mm lance extension.
B: Use for 300-mm lance extension.
E 2016 Nordson Corporation
Part 1604857-11
7-10 Parts
Controller Parts
Front Panel and Internal Cabinet Ground Parts Illustration
1
2
7
3
6
9
10
5
11
12
4
8
13
Rear Panel Assembly
See Figures 7-11 and 7-12 for
parts
Figure 7-10 Controller Parts
Part 1604857-11
E 2016 Nordson Corporation
Parts
7-11
Front Panel and Internal Cabinet Ground Parts List
Refer to Figure 7-10.
Item
Part
Description
Quantity
−
1107552
CONTROLLER ASSY, manual, Encore LT,
packaged
1
1
1108279
S KIT, PCA, control, Encore LT
1
2
1108312
S PANEL, keypad, Encore LT/auto controller,
packaged
1
3
982916
S SCREW, flat, socket, M5 x 10, black
4
4
982636
S SCREW, button, socket, M5 x 12, zinc
2
5
983127
S WASHER, lock, internal, M5, zinc
2
6
983403
S WASHER, lock, split, M4, steel, zinc
4
7
982881
S SCREW, pan head, recessed, M4 x 6, zinc
2
8
1045837
S SCREW, pan head, recessed, M5 x 12
w/lockwasher, black
2
9
984702
S NUT, hex, M5, brass
1
10
983401
S WASHER, lock, split, M5, steel, zinc
1
11
983021
S WASHER, flat, 0.203 x 0,406 x 0.040, brass
1
12
933469
S LUG, 90, double, 0.250, 0.438 in.
1
13
240674
S TAG, ground
1
E 2016 Nordson Corporation
Note
Part 1604857-11
7-12 Parts
Rear Panel Parts Illustration
Manifold Assembly
See Figure 7-12
4X
9
10
13
11
14
15
16
22
21
17
19
18
(this screw
only)
25
20
26
23
Figure 7-11
24
23
23
Rear Panel Parts
Part 1604857-11
E 2016 Nordson Corporation
Parts
7-13
Rear Panel Parts List
Refer to Figure 7-11.
Item
Part
14
Description
Quantity
984526
S NUT, lock, 1/2 in. conduit
1
15
939122
S SEAL, conduit fitting, 1/2 in., blue
1
16
1107539
S RECEPTACLE, gun, Encore LT
1
17
1045837
S SCREW, pan head, recessed, M5 x 12, with
lockwasher, black
4
18
1068715
S WASHER, lock, dished, #10
1
19
972930
S PLUG, push in, 8 mm tubing, plastic
1
20
972808
S CONNECTOR, strain relief, 1/2 in. NPT
2
21
984192
S NUT, lock, 1/2 in. NPT, nylon
2
22
117549
S GASKET, panel, rear, Encore LT controller
1
23
982824
S SCREW, pan head, recessed, M3 x 8, with
lockwasher, black
10
24
1107696
S FILTER, line, RFI power, 3A, with 0.250 QD
1
25
1606835
S KIT, PCA, relay board, Encore LT−HD
1
26
1107695
S POWER SUPPLY, 24VDC, 60W
1
E 2016 Nordson Corporation
Note
Part 1604857-11
7-14 Parts
Manifold Illustration and Parts List
33
32
27
28
27
31
30
29
34
35
Figure 7-12 Manifold Parts
Item
Part
Description
Quantity
27
1030873
S VALVE, check, M8 x R1/8, M input
2
28
1107596
S CONNECTOR, male, with internal hex, 10 mm
tube x 1/8 unithread
1
29
1062009
S CONNECTOR, male, with internal hex, oval
collar, 4 mm tube x M5
1
30
972399
S CONNECTOR, male, with internal hex, 6 mm
tube x 1/8 unithread
1
31
1604486
S VALVE, flow control, 6 mm x 1/8 R
1
32
1108313
S MUFFLER, exhaust, 1/8 R
1
33
1107593
S GASKET, manifold, controller, Encore LT
1
34
1107597
S REGULATOR, electro-pneumatic
2
35
1099281
S VALVE, solenoid, 3 port, 24V, 0.35W
3
Part 1604857-11
Note
E 2016 Nordson Corporation
Parts
7-15
System Components and Parts
3
1A
2
1
Figure 7-13 Miscellaneous System Parts
Item
Part
Description
1
1097809
TUBE, fluid, pickup, w/cond. fitting, VBF, Encore
1A
1096788
S CONN, 6mm tube x R 1/8, dia 0.7mm orifice
2
1084760
ISOLATOR, vibration, 1.0 dia x 1.5 x 5/16 studs
3
1604512
VIBRATOR, electric, 115V, 60 Hz, w/cord grip
3
1108091
VIBRATOR, electric, 230V, 50 Hz, w/cord grip
NS
1107552
CONTROLLER, manual, Encore LT, packaged
NS
1095922
PUMP assembly, corona, Encore Gen II
NS
1106893
HANDGUN ASSY, Encore LT
NS
1107949
HOPPER, NHR Encore, 50-lb
NS
972841
CONN, male, 10 mm tubing x 1/4 unithread
NS
1093708
GROMMET, 0.719 ID x 1.281 OD x 0.093 GR
NS
134575
WIRE, ground (with ground clamp)
NS
1107895
KIT, VBF pickup tube arm assembly, Encore LT
NS
1107903
S KIT, pickup tube collar, Encore LT
NS
1107913
KIT, rail mount, Encore LT
NS
1600437
KIT, wall mount, Encore LT
NS
1067694
KIT, ground bus bar, ESD, 6 position, w/hardware
NS
1085679
KIT, pump adapter, hopper, Encore
NS
1082204
COUPLING, pump, Encore
NS
972262
REDUCER, 10 mm stem x 6 mm tubing
NS
1600658
HANGER, gun, Encore LT
NS
1600566
KIT, filter, Encore LT
NS
1600608
S FILTER, mist separator, 0.3 micron, 1/2 in. NPT
NS
1600609
S S FILTER ELEMENT, separator, 0.3 micron
NS
1604487
VALVE, flow control, 4-mm tube x 4-mm tube
NOTE A: VBF systems only. Order the correct vibrator motor for your VBF system.
Quantity
Note
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
D
A
A
A
B
A
A
1
1
1
1
1
1
1
1
1
C
C
C
F
E
E
G
B: Hopper systems only. Hopper includes pickup tube.
C: Included with both wall- and rail-mount systems.
D: Conductive fitting. Do not replace with a non-conductive fitting.
E: Filter kit includes fittings and mounting bracket. Order filter only to replace mobile system filter.
F: Install in hopper plenum elbow.
G: Connect to air wash connector on controller rear panel to control air flow.
NS: Not Shown
E 2016 Nordson Corporation
Part 1604857-11
7-16 Parts
Powder Hose and Air Tubing
Powder hose and air tubing must be ordered in increments of one foot.
Part
Description
Note
768176
Powder hose, 11 mm antistatic
A, E
768178
Powder hose, 12.7 mm (1/2 in.) antistatic
A, E
900648
Powder hose, 11 mm blue
D
(1/2
900650
Powder hose, 12.7 mm
900617
Air tubing, polyurethane, 4 mm, clear
in.) blue
D
B
900742
Air tubing, polyurethane, 6 mm, blue
B
1096789
Air tubing, antistatic, 6/4 mm, black (conductive air tubing)
C
900741
Air tubing, polyurethane, 6 mm, black
900618
Air tubing, polyurethane, 8 mm, blue
B
900619
Air tubing, polyurethane, 8 mm, black
B
900740
Air tubing, polyurethane, 10 mm, blue
B
900517
Tubing, poly, spiral cut, 0.62 in. ID
301841
Strap, Velcro, w/buckle, 25 x 3 cm
NOTE A: Twenty feet of 11-mm antistatic hose is provided with the systems. If you need to use a longer length, you
must switch to the 1/2 inch hose to prevent powder delivery issues.
B: Minimum order quantity is 50 ft.
C: This tubing is used on VBF systems to provide fluidizing air from the bulkhead union to the pickup tube. It
is conductive and grounds the pickup tube to the cart body. Do not replace with non-conductive tubing.
D: Minimum order quantity is 25 ft.
E: Minimum order quantity is 100 ft.
System Options
Part
Description
Quantity
1091429
KIT, input air, Encore manual systems
972841
S CONNECTOR, male, 10 mm tube x 1/4 in. unithread
1
3/
8
971102
S CONNECTOR, male, 10 mm tube x
973500
S COUPLING, pipe, hydraulic, 1/4 in., steel, zinc
3/
8
Note
973520
S COUPLING, pipe, hydraulic,
900740
S TUBING, polyurethane, 10 mm, blue
1086131
1600188
BRACKET, adapter, dual pickup tube
KIT, small parts tray
in. unithread
in., steel, zinc
1
1
1
1
20 ft
A
1
1
B
C
NOTE A: Replacement tubing has a minimum order quantity of 50 ft.
B: Use this bracket to install two pickup tubes on the arm assembly.
C: For mobile systems only. To install the tray, remove the 2 top screws from the controller tower, install the
#10 dished lock washer in the kit on one screw, then use the screws to install the tray.
Part 1604857-11
E 2016 Nordson Corporation
Parts
7-17
Optional Transportable Manual System
This system consists of an Encore LT manual powder spray system packed
into a case for transportation. The following parts list consists of
replacements for the components in the system.
Part
Description
1602351
SYSTEM, transportable, Encore LT
1602463
S CASE, transportable, Encore LT
1106893
S HANDGUN assembly, manual, Encore LT
1107552
S CONTROLLER ASSY, manual, Encore LT, packaged
1095922
S PUMP assembly, corona, Encore Gen II, packaged
1100777
S KIT, cup gun, Encore
1082060
S NOZZLE, conical, Encore
1083206
S DEFLECTOR assembly, conical, 26 mm, Encore
1083201
S DEFLECTOR assembly, conical, 16 mm, Encore
1082185
S NOZZLE, cross−cut, 2.5 mm, 90 degree, Encore
1081656
S NOZZLE, flat spray, 2.5 mm, Encore
1081659
S NOZZLE, flat spray, 6 mm, Encore
1085679
S KIT, pump adapter, hopper, Encore
1082204
S COUPLING, pump, Encore
768176
S TUBING, powder, antistatic, 11 mm (.43 in)
900740
S TUBING, polyurethane, 10/6.5−7 mm
900517
S TUBING, spiral cut, .62 in. ID
900742
S TUBING, polyurethane, 6/4 mm, blue
972262
S REDUCER, 10 mm stem
1081658
S NOZZLE, flat spray, 4 mm, Encore
NOTE A: Minimum order quantity is 100 ft.
Quantity
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6 ft
6 ft
1.5 ft
6 ft
1
1
Note
A
B
C
B
D
B: Minimum order quantity is 50 ft.
C: Order in increments of one foot.
D: 4-mm flat spray nozzle is shipped with the spray gun.
Figure 7-14 Encore LT Transportable System
E 2016 Nordson Corporation
Part 1604857-11
7-18 Parts
Part 1604857-11
E 2016 Nordson Corporation
Wiring Diagram
8-1
Section 8
Wiring Diagram
E 2016 Nordson Corporation
Part 1604857-11
8-2
Wiring Diagram
Part 1604857-11
E 2016 Nordson Corporation
J4
(BLACK)
(BLACK)
PURGE
NOZZLE
ENCORE LT
CONTROLLER
MANIFOLD ASSY
J6
J3
3 2 1
J5
(RED) FLOW
(BLACK) FLOW
(WHITE) FLOW
3 2 1
J8
ENCORE LT
CONTROL PCA
8-3
FLUIDIZING
(RED) FLUIDIZING
(BLACK) FLUIDIZING
(RED) PURGE
(BLACK) PURGE
(RED) NOZZLE
(BLACK) NOZZLE
6 5 4 3 2 1
J7 (VBF)
ENCORE LT/ KEYPAD PANEL
2 1
Wiring Diagram
(RED) ATOMIZING
(BLACK) ATOMIZING
(WHITE) ATOMIZING
FLOW
A.C. POWER HARNESS
(RELAY TO CTRLR)
ATOMIZING
(POWER)
J10
J1
(BLACK) DC COM
(RED) +24VDC
A.C. POWER HARNESS
(FILTER TO RELAY)
A.C. POWER HARNESS
(FILTER TO P.S.)
(BLACK)
POWER SUPPLY TO
CTRLR HARNESS
LINE FILTER
1107696
(RED) +24VDC
SK1
1 2 3 4 5 6
PURGE
60W DC
POWER
SUPPLY
L
N
(BROWN)
(N/C)
J1
ENCORE LT
RELAY PCA
F2
L2
L1 F
(BROWN)
(BROWN)
L1
F1
RL1
C1
M1 M2 M3
C2
JP1
230V MOTOR
M1 M2 M3
(BLUE)
(RED)
15 FT (4.6M)
POWER CORD
(WHITE)
GND
NO.1
(BLACK)
M1 M2 M3
(GREEN)
A.C. POWER HARNESS
(GROUND JUMPER 2)
115V MOTOR
(BLACK)
(GREEN/YELLOW)
GND
NO.3
Jumper JP1 for 115V Motor
Remove Jumper for 230V Motor
VBF POWER CORD
(MOBILE SYSTEMS W/VBF ONLY)
(BROWN)
GND
NO.2
(YEL/GRN)
(GROUND
JUMPER 3)
A.C. POWER HARNESS
(GROUND JUMPER 1)
(BROWN) L (L1 - HOT)
(GREEN/YELLOW)
(LT BLUE) N (L2 - NEUTRAL)
(GREEN/YELLOW)
6 (GREEN) GROUND
GUN
RECEPTACLE
(LT BLUE)
(BLUE)
(BROWN)
1
2
L2 F
(BLUE)
(BLUE)
(GREEN W/YELLOW)
DC COM
2 (BLACK)
(BLACK) DC COM
1 (ORANGE)
5 (YELLOW)
4 (WHITE)
3 (RED)
FEEDBACK
TRIGGER
OSC
SK2
(BLACK)
(ORANGE)
(BLACK)
(RED)
(WHITE)
(YELLOW)
5 4 3 2 1
5 4 3 2 1
J2 (GUN)
1 2 3 4 5 6
CONTROLLER
CABINET
GND
NO.4
VBF POWER CORD WIRING
Figure 8-1
Encore LT Manual Controller Wiring Diagram
E 2016 Nordson Corporation
Part 1604857-11
DECLARATION of CONFORMITY
PRODUCT: Encore LT Automatic and Manual Powder Spray Systems
Encore Automatic Applicator and Encore LT Automatic Controllers
Encore LT Manual Applicator with Encore LT Manual Controller
Description: The automatic electrostatic powder spray system includes applicator, control cable, and
associated controllers. These controllers are available in a one applicator, dual applicator, or 4−8 applicator
system. The 4−8 applicator system is available with or without Axis control for movement of the applicators
in and out of the booth. The manual powder electrostatic powder spray system includes applicator, control
cable, and associated controls. This is available in a stationary system, or in a mobile system.
Models:
Applicable Directives:
2006/42/EC − Machinery Directive
2014/30/EU − EMC Directive
2014/34/EU − ATEX Directive
Standards Used for Compliance:
EN/ISO12100-1 (2010)
EN60079-0 (2009)
EN60079-31 (2009)
EN60204-1 (2006)
EN50050 (2006)
EN50177 (2009)
EN61000-6-3 (2007)
EN61000-6-2 (2005)
EN55011 (2009)
FM7260 (1996)
Type of Protection:
− Ambient Temperature: +15_C to 40_C
− Ex II 2 D / 2mJ = Manual and Automatic Applicators / Automatic Applicators are Type: A-P per EN50177
− EX II (2) 3 D = Manual and Automatic Controllers
− EX II (2) D = Automatic 4−8 Applicator Controller with Axis Control
ATEX Product Certificates:
− FM11ATEX0056X (Applicators) (Norwood, Mass. USA)
− FM11ATEX0057X (Controllers) (Norwood, Mass. USA)
ATEX Quality System Certificate:
− 1180 Baseefa (Buxton, Derbyshire, UK)
Date: 16 Aug 2016
Vance Wilson
Engineering Manager
Industrial Coating Systems
Nordson Authorized Representative in the EU
Person authorized to compile the relevant technical documentation.
Contact:
Operations Manager
Industrial Coating Systems
Nordson Deutschland GmbH
Heinrich−Hertz−StraBe 42−44
D−40699 Erkrath
Nordson Corporation S Westlake, Ohio
DOC14033_03
MATERIAL NO.
8
NOTICE
5
6
7
4
3
1107255
REVISION
04
1
THIS DRAWING IS NORDSON PROPERTY,CONTAINS PROPRIETARY INFORMATION AND MUST BE RETURNED UPON REQUEST.
DO NOT CIRCULATE, REPRODUCE OR DIVULGE TO OTHER PARTIES WITHOUT WRITTEN CONSENT OF NORDSON.
D
D
6M MANUAL GUN CABLE EXTENSION,
6-CONDUCTOR, SHIELDED.
1085168
C
ENCORE 6M MANUAL GUN
CABLE ASSEMBLY
1106756
ENCORE LT MANUAL CONTROL UNIT
1107552
C
ENCORE LT MANUAL GUN 1106893
B
B
PART NUMBER
APPROVED EQUIPMENT FOR THE FOLLOWING
POWDER SYSTEMS:
THE FOLLOWING CONTROLLER IS SUITABLE FOR
CLASS II, DIV. 2, GROUP F & G HAZARDOUS
(CLASSIFIED) LOCATIONS OR ZONE 22 (EU):
THE APPLICATOR AND CABLES ARE
SUITABLE FOR CLASS II, DIV 1, GROUP F & G
HAZARDOUS (CLASSIFIED) LOCATION OR
ZONE 21 (EU):
01
DESCRIPTION
cFMus & ATEX
1108212
SYSTEM,RAIL MOUNT,ENCORE LT
&
1600438
SYSTEM,WALL MOUNT,ENCORE LT
&
1107552
CONTROL UNIT,MANUAL,ENCORE LT,PKGD
&
1106893
HANDGUN ASSY,ENCORE LT
&
1106756
CABLE ASSY,HANDGUN,ENCORE LT/XT,6M
&
1085168
CABLE,6-WIRE SHIELDED,HANDGUN,6M EXT
&
CRITICAL
No revisions permitted without
approval of the proper agency.
ALL DIMENSIONS IN
A
WESTLAKE, OH, U.S.A. 44145
EXCEPT AS NOTED
X±0.8
X.X±0.25
MACHINED SURFACES
X.XX±0.13
THREAD LENGTH DIMENSIONS ARE
FULL THREAD
INTERPRET DRAWINGS PER ASME
Y14.5-1994
PERFECT FORM AT MMC REQUIRED
FOR INTERRELATED FEATURES
THIRD ANGLE
PROJECTION
8
7
6
5
4
3
DESCRIPTION
REF DWG,APVD EQPT,MANUAL,ENCORE LT
1.6
BREAK INSIDE/OUTSIDE CORNERS
0.1/0.8
A
NORDSON CORPORATION
MM
DRAWN BY
DC
CHECKED BY
SIZE
RJF
FILE NAME
D
SCALE
2
1107255
NOT TO SCALE
DATE
APPROVED BY
MATERIAL NO.
07APR11
RELEASE NO.
PE602493
RJF
REVISION
1107255
SOLIDWORKS GENERATED DWG.
04
SHEET
1
1
OF
2
MATERIAL NO.
8
NOTICE
7
6
5
1107255
3
4
REVISION
04
1
THIS DRAWING IS NORDSON PROPERTY,CONTAINS PROPRIETARY INFORMATION AND MUST BE RETURNED UPON REQUEST.
DO NOT CIRCULATE, REPRODUCE OR DIVULGE TO OTHER PARTIES WITHOUT WRITTEN CONSENT OF NORDSON.
D
D
C
C
6M MANUAL GUN CABLE EXTENSION,
6-CONDUCTOR, SHIELDED.
1085168
03
115V VIBRATOR MOTOR 1604512
230V VIBRATOR MOTOR 1108091
WITH EXTRA-HARD USAGE ELECTRICAL CORD
UL/CSA APPROVED 18 AWG 90 C
230V = VIBRATOR MANUFACTURER'S CERT. #: TUV12ATEX094817
115V = VIBRATOR MANUFACTURER'S CERT. #: ETL CERTIFIED US & CANADA
04
B
ENCORE 115V & 220V VBF
MOBILE POWDER SYSTEMS
1107897 OR 1107898
ENCORE 50LB HOPPER
MOBILE POWDER SYSTEM
1107901
HEIGHT: 995 mm [35.2 in]
LENGTH: 820 mm [32.25 in]
WHEEL BASE: 598.5 mm [23.5 in]
WEIGHT: 46.7 kg [103 lbs]
HEIGHT: 995 mm [35.2 in]
LENGTH: 812 mm [32 in]
WHEEL BASE: 598.5 mm [23.5 in]
WEIGHT: 50.4 kg [111 lbs]
PART NUMBER
APPROVED EQUIPMENT FOR THE FOLLOWING
MOBILE POWDER SYSTEMS:
THE FOLLOWING CONTROLLER IS
SUITABLE FOR CLASS II, DIV 2, GROUP F & G
HAZARDOUS (CLASSIFIED) LOCATIONS OR
ZONE 22 (EU):
THE APPLICATOR AND CABLES
OF THESE UNITS ARE SUITABLE FOR
IN A CLASS II, DIV 1, GROUP F & G HAZARDOUS
(CLASSIFIED) LOCATION OR ZONE 21 (EU):
01
DESCRIPTION
ATEX
cFMus
cFMus & ATEX
1107897
SYSTEM,DOLLY W/VBF,115V,ENCORE LT
1107898
SYSTEM,DOLLY W/VBF,220V,ENCORE LT
1107901
SYSTEM,DOLLY W/HOPPER,ENCORE LT
&
1107552
CONTROL UNIT,MANUAL,ENCORE LT,PKGD
&
1106893
HANDGUN ASSY,ENCORE LT
&
1106756
CABLE ASSY,HANDGUN,ENCORE LT/XT,6M
&
1085168
CABLE,6-WIRE SHIELDED,HANDGUN,6M EXT
&
B
&
&
CRITICAL
No revisions permitted without
approval of the proper agency.
ALL DIMENSIONS IN
A
WESTLAKE, OH, U.S.A. 44145
EXCEPT AS NOTED
X±0.8
X.X±0.25
MACHINED SURFACES
X.XX±0.13
THREAD LENGTH DIMENSIONS ARE
FULL THREAD
INTERPRET DRAWINGS PER ASME
Y14.5-1994
PERFECT FORM AT MMC REQUIRED
FOR INTERRELATED FEATURES
THIRD ANGLE
PROJECTION
8
7
6
5
4
3
DESCRIPTION
REF DWG,APPROVED EQUIPMENT,MANUAL,ENCORE
1.6
BREAK INSIDE/OUTSIDE CORNERS
0.1/0.8
A
NORDSON CORPORATION
MM
DRAWN BY
DC
CHECKED BY
SIZE
RJF
FILE NAME
D
SCALE
2
1107255
NOT TO SCALE
DATE
APPROVED BY
MATERIAL NO.
07APR11
RELEASE NO.
PE602493
RJF
REVISION
1107255
SOLIDWORKS GENERATED DWG.
04
SHEET
1
2
OF
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising