PowerVIEW HD-22 and HD-30 QDVI Manual

PowerVIEW HD-22 and HD-30 QDVI Manual
Installation and User Guide
VADDIO™ POWERVIEW™ HD-22 QDVI AND
POWERVIEW HD-30 QDVI CAMERA SYSTEMS
PowerVIEW Series High Definition PTZ Cameras featuring the Quick-Connect™
DVI/HDMI-SR Interface
PowerVIEW HD-22 QDVI - High Definition PTZ Camera System (22X Optical Zoom)
Model Number 999-6966-000 (North America)
Model Number 999-6966-001 (International)
PowerVIEW HD-30 QDVI - High Definition PTZ Camera System (30X Optical Zoom)
Model Number 999-6976-000 (North America)
Model Number 999-6976-001 (International)
PowerVIEW 22/30 with CONCEAL Mount
Quick-Connect DVI/HDMI SR Interface
© 2015 Vaddio - All Rights Reserved. PowerVIEW HD-22 and HD-30 QDVI Camera Systems - Document Number 342-0644 Rev D
PowerVIEW HD-22 and HD-30 QDVI Systems
Inside Front Cover - Mostly Blank
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 2 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
TABLE OF CONTENTS
Overview .................................................................................................................................................................... 4 Unpacking .................................................................................................................................................................. 5 Camera Front View with Feature Call-outs ............................................................................................................ 6 Image: PowerVIEW HD-22/30 QDVI Camera System ...................................................................................... 6 Rear Panel Connections with Feature Call-outs .................................................................................................... 7 Image: PowerVIEW HD-22/30 QDVI Camera System ...................................................................................... 7 First Time Set-up with the PowerVIEW HD-22 or HD-30 QDVI System ................................................................... 7 Image: PowerVIEW HD-22/30 Rear Panel Connections .................................................................................. 8 Drawing: Dip Switch and Resolution Label on the Bottom of the HD-22/30 ...................................................... 8 Quick-Connect DVI/HDMI SR Interface..................................................................................................................... 9 Image: Rear Panel Connectors and Features................................................................................................... 9 Image: Quick-Connect DVI/HDMI SR Interface Front Panel ............................................................................ 9 Installation Procedures ............................................................................................................................................ 10 Before Installing: .................................................................................................................................................. 10 Installation Basics: ............................................................................................................................................... 10 General Installation Instructions for the CONCEAL Wall Mounting System: ....................................................... 10 Image: Basic Connectivity Example of the HD-22 or HD-30 ........................................................................... 12 Daisy Chain Configurations ..................................................................................................................................... 13 Compliance and CE Declaration of Conformity - PowerVIEW HD-22 and HD30 ................................................... 14 Compliance and CE Declaration of Conformity - Quick-Connect DVI/HDMI SR Interface ..................................... 15 Warranty Information ............................................................................................................................................... 16 General Specifications ............................................................................................................................................. 17 Appendix 1: Pin-Outs for the HD-22/30 Camera ................................................................................................... 18 Drawing: PowerVIEW HD-22/30 Camera Dimensions.................................................................................... 19 Communication Specification .................................................................................................................................. 20 HD-22/30 Command List (1/2) ......................................................................................................................... 20 HD-22/30 Command List (2/2) ......................................................................................................................... 21 HD-22/30 Inquiry List (1/1) ............................................................................................................................... 22 PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 3 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
OVERVIEW
The remarkable Vaddio PowerVIEW HD-22 and HD-30 high
definition PTZ cameras are available in the super-versatile Vaddio
PowerVIEW QDVI system packages. The PowerVIEW HD-22 QDVI
and the PowerVIEW HD-30 QDVI feature 22X and 30X power zoom
optics respectively. These cameras use a CMOS, 1/2.8-Type,
progressive scan image sensors, which provide for better light
sensitivity, increased noise reduction and lower power consumption
than cameras with either CCD or CMOS image sensors. This
advanced MOS image sensor captures realistic textures, vivid colors
and delicate gradations that are comparable to 3-chip camera
performance.
Both the HD-22 and the HD-30 provide matchless low-light
capabilities with a minimum illumination rating of an amazing 0.4 lux
(color) and 0.04 lux (B/W). Equipped with a 2.2 megapixel CMOS
sensor, the cameras deliver native FULL HD 1080p/60 high definition
video resolution and superior color reproduction for use in any
professional A/V presentation, videoconferencing, House of Worship,
education, live event and industrial applications.
Image: PowerVIEW HD-22 or HD-30 PTZ Camera (above)
and the Quick-Connect DVI/HDMI SR Interface (below)
The HD-22 has a powerful 22X multi-element glass zoom lens (f=4.3mm to 94.6mm) and works exceptionally well
in large rooms. However, the premium optics also provides a super-wide horizontal field of view of 65.2º, which
works very well in small room video applications. The HD-30, as one could probably guess, has a robust 30X
optical power zoom lens that enables the capture of brilliant and detailed video images even in the largest rooms.
The cameras output multi-format HD video in both analog component (YPbPr), HDMI and differential formats in HD
resolutions of 1080p/59.94, 1080p/50 1080p/29.97 1080p/25, 1080i/59.94, 1080i/50, 720p/59.94, 720p/50 and
progressive SD resolutions of 480p/59.97 and 576p/50. Both cameras are offered with DVI/HDMI SR packages
with the Quick-Connect DVI/HDMI SR Interface that uses HSDS™ for distribution of video, power and control over
Cat-5 cable up to 100’ (30.48m) and are capable of providing analog component YPbPr and HDMI concurrently
from the Quick-Connect interface. The PowerVIEW HD-22 QDVI and HD-30 QDVI camera systems represent an
exceptional value and are superb performers for even the most demanding video applications.
Intended Use:
Before operating the device, please read the entire manual thoroughly. The system was designed, built and tested
for use indoors with the power supply provided. The use of a power supply other than the one provided or outdoor
operation hasn’t been tested and may damage the device and/or create an unsafe operating condition.
Important Safeguards:
Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged.
In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock,
do not immerse in water or other liquids and avoid extremely humid conditions.
Use only the power supply provided with the system. Use of any unauthorized
power supply will void any and all warranties.
Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not
work well for professional installations and can be the cause of intermittent connections which
can result in the RS-232 control line failing and locking up, and/or compromising the HSDS (high
speed differential) signals. For best results please use standard RJ-45 connectors and test all
cables for proper pin-outs prior to use and connection to Vaddio product.
Save These Instructions:
The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from
www.vaddio.com free of charge.
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 4 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
UNPACKING
Carefully remove the product and all of the included parts from the packaging.
Identify the following parts for each camera:
PowerVIEW HD-22 QDVI Camera System (North America):
Part Number: 999-6966-000

One (1) PowerVIEW HD-22 HD PTZ Camera (998-6960-000)

One (1) Vaddio IR Remote Commander

One (1) Quick-Connect DVI/HDMI-SR Interface

One (1) 3-Position Phoenix-type Connector for IR Forwarding

One (1) 24 VDC, 2.0 A Power Supply with Power Cord for North America

One (1) CONCEAL Wall Mount with Mounting Hardware

One (1) EZCamera™ Control Adapter (RJ-45-F to DB-9-F)

Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
PowerVIEW HD-22 QDVI Camera System (International):
Part Number: 999-6966-001

One (1) PowerVIEW HD-22 HD PTZ Camera (998-6960-000)

One (1) Vaddio IR Remote Commander

One (1) Quick-Connect DVI/HDMI SR Interface

One (1) 3-Position Phoenix-type Connector for IR Forwarding

One (1) 24 VDC, 2.0 A Power Supply

One (1) Euro Power Cable

One (1) UK Power Cable

One (1) CONCEAL Wall Mount with Mounting Hardware

One (1) EZCamera Control Adapter (RJ-45 to DB-9)

Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
PowerVIEW HD-30 QDVI Camera System (North America):
Part Number: 999-6976-000

One (1) PowerVIEW HD-30 HD PTZ Camera (998-6970-000)

One (1) Vaddio IR Remote Commander

One (1) Quick-Connect DVI/HDMI SR Interface

One (1) 3-Position Phoenix-type Connector for IR Forwarding

One (1) 24 VDC, 2.0 A Power Supply with Power Cord for North America

One (1) CONCEAL Wall Mount with Mounting Hardware

One (1) EZCamera Control Adapter (RJ-45-F to DB-9-F)

Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
PowerVIEW HD-30 QDVI Camera System (International):
Part Number: 999-6976-001

One (1) PowerVIEW HD-30 HD PTZ Camera (998-6970-000)

One (1) Vaddio IR Remote Commander

One (1) Quick-Connect SR Interface

One (1) 3-Position Phoenix-type Connector for IR Forwarding

One (1) 24 VDC, 2.0 A Power Supply

One (1) Euro Power Cable

One (1) UK Power Cable

One (1) CONCEAL Wall Mount with Mounting Hardware

One (1) EZCamera Control Adapter (RJ-45 to DB-9)

Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
CONCEAL Mount includes:

Metal Bracket (black)

Bottom Cover

Rear Connector/Cable Cover

Mounting Hardware
Page 5 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
Camera Front View with Feature Call-outs
Image: PowerVIEW HD-22/30 QDVI Camera System
①
②
④
③
1) Camera and Zoom Lens:
The 22X (HD-22) or 30X (HD-30) optical zoom lens is built around a (1/2.8 Type) high-speed MOS image sensor
with a total of 2.2 megapixels for precise HD video image acquisition.
2) Red Tally Light:
A red tally light is illuminated when the camera receives a command from an external controller.
3) IR Sensors:
IR sensors are built into the front of the HD-22 and HD-30 to receive IR signals from the IR remote control
supplied with the camera.
4) Blue Power Light:
A Vaddio blue power light is illuminated when the camera is turned on. This LED will blink when the camera
receives IR signals from the Vaddio IR Remote Commander.
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 6 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
Rear Panel Connections with Feature Call-outs
Image: PowerVIEW HD-22/30 QDVI Camera System
⑤
⑥
⑦
⑨
⑩
⑪
⑧
⑫
5) RS-232 IN & IR Out:
The RS-232 port accepts modified VISCA protocol for camera control and transmits IR signaling received by the
IR receivers, which can be relayed to third party equipment (IR Forwarding) through the Quick-Connect DVI/HDMISR Interface.
6) Dip Switch Settings:
Settings for IR remote, baud rate and image flip can be configured on these switches. See the Switch Settings
page for additional information.
7) HD Video Select:
A rotary switch allows the user to choose the component HD output video resolution and format. See the Switch
Settings page for additional information.
 HD Resolution Note: When changing the resolution of the camera, the camera may need to be power-cycled
after the change. Pretty much every switcher will have to be reset or rebooted as well.
8) 12 VDC Input:
Power input for the standard 12 VDC, 3.0 Amp power supply for the HD-22 and HD-30. The 12 VDC power supply
is only used with the standalone cameras, but not with the QDVI systems).
9) HDMI Output:
The HDMI output feeds out HD digital video only (no copy protect or device communication is required). The HDMI
output is optimized for high definition video signals.
10) YPbPr Output:
Component HD video (YPbPr) is output through the DE-15 connector. YPbPr and HDMI signals have simultaneous
output. Limited SD (YPbPr) resolutions are supported.
11) EZ Power HD Video Port:
This RJ-45 connector is used with the Quick-Connect SR type interfaces to supply power and return HSDS
(differential) video from the camera. Please mark and test cables for voltage prior to connection.
12) Slot for Optional Cards:
The EZIM CCU slot card for the CCU can be plugged into the PowerVIEW HD-22 HD camera.
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 7 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
FIRST TIME SET-UP WITH THE POWERVIEW HD-22 OR HD-30 QDVI SYSTEM
The PowerVIEW HD-22 and HD-30 cameras in the QDVI Kit were designed to be very easy to use and operate.
There is documentation at the back of this manual for pin-outs of the connectors.
Step 1: Using the HD VIDEO SELECT rotary switch and CAMERA SETTINGS DIP switches on the back of the
camera, set up the camera’s output resolution and functional preferences. There is a label on the bottom of the
camera that identifies the choices.
Important Dip Switch Note: Setting all dip switches down and power cycling the camera will load the factory default camera settings. For the
first time set-up, loading the defaults may be a good idea.
Image: PowerVIEW HD-22/30 Rear Panel Connections
HD Video Select Switch
(Set HD resolution)
Camera Settings 10-Pos Dip Switch
(Set functional preferences)
HD-22/30 Rear Panel
Drawing: Dip Switch and Resolution Label on the Bottom of the HD-22/30
②
IR 1
1 & 2 UP
① VIDEO RESOLUTION SELECT
DIP SWITCH SETTINGS
IR
OUT
OFF
9600
bps
5
OFF
6
OFF
HDMI IMAGE
9
COLOR FLIP
OFF
YCbCr OFF
10
OFF
⑦
All Down
with Power
Cycle for
Defaults
IR 2
ON
IR 3
ON
1
2
ON
38400
bps
3
4
③ ④
5
6
sRGB
ON
7
8
⑤ ⑥
9
0
1
2
3
4
5
6
7
720p/59.94
1080i/59.94
1080p/59.94
720p/50
1080i/50
1080p/50
480p/59.94
8
9
A
B
C
D
E
F
576p/50
1080p/29.97
1080p/25
10
Setting the Switches:
1) Set the desired and available HD output resolution for the camera with the Rotary Switch.
2) Set the IR control frequency of the camera if it is to respond to the IR remote control.
3) If using the IR forwarding features with a 3rd party codec remote, set the IR OUT switch to ON (SW3).
4) Set the Baud Rate dip switch (SW4) to 9600bps for most applications. Default is 9600 bps for Cat-5 systems.
5) To set the HDMI or DVI color space, use dip switch 7 (SW7).
6) If inverting the camera, turn the IMAGE FLIP ON (SW8).
7) All dip switches DOWN with a power cycle loads the default camera settings. Return dips to desired operating position.
Dip Switch Settings Explained:






IR 1, 2 and 3 (SW 1 &2): A single IR remote has the capability of operating up to three different PTZ cameras in a
room. Use these selector dip switches and the selector buttons at the top of the IR remote to select the frequency.
IR OUT on/off (SW3): The IR output is sent out on the RS-232 RJ-45 jack on the back of the camera. Turning on
the IR output will allow IR signals to be transmitted over the Cat-5 cable to the head end from 3rd party remotes.
When using RS-232 control or Vaddio CCU controllers (also via RS-232), turn the IR OUT to OFF (up).
Baud Rate (SW4): The options for baud rate are either 9600 or 38,400 bps. The 9600 bps works best with Cat-5.
HDMI Color or sRGB Color space (SW7): Default is YCbCr. Use sRGB color space with older DVI-D 1.0
equipment or monitors only. The YCbCr color space is used for HDMI digital video.
Image Flip (SW8): To invert the HD-20, turn the IMAGE FLIP ON (switch down).
Dip Switches 5, 6, 9 and 10: Not used for operation, please leave these dip switches up or in the OFF position.
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 8 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
QUICK-CONNECT DVI/HDMI SR INTERFACE
Image: Rear Panel Connectors and Features
①
②
③
④
⑤
⑥
⑦
⑨ ⑩
⑧
1) Power Light: Blue LED Power Indicator
2) 24 VDC Power Port: Coax Power Connector, 5.5mm OD x 2.5mm ID, Positive Center.
3) Recessed Color Space Conversion Switch: Toggles between HDMI YCbCr and sRGB (RGBHV) color
space. Change the color space to accommodate either HDMI or DVI-D monitors.
4) RS-232 INPUT (Color Coded Grey): For use with joystick controller, codec or control system.
5) RS-232 OUT TO CAMERA (Color Coded Blue): RS-232 Control to & from Camera and IR signals returned
from the camera.
6) Daisy Chain Control Port: Daisy Chain Control Emulation (DCCE) output to next Quick-Connect DVI/HDMI
SR Interface (does not function with the AutoTrak System).
7) IR Output Port: Non-modulated (for hard connections) and Modulated for use with IR emitters.
8) DVI-D Output: High Definition Multimedia Interface (HDMI) Transmitter, HDMI (v 1.3 with deep color) and
DVI v 1.0 Compliant - use Recessed Color Space Conversion Switch ③ to toggle between HDMI YCbCr and
DVI-D sRGB color spaces to suit your monitors
9) YPbPr Output: Analog Component Video Output on DE-15F (HD-15F) Connector, Resolutions up to
1080p/60 with monitor support.
10) EZ-POWER VIDEO Port (Color Coded Orange): Supplies power to camera and returns HD video from the
camera via Cat-5e. Maximum distance on the Cat-5e cable is 100’ (30.5 m).
Image: Quick-Connect DVI/HDMI SR Interface Front Panel
①
②
1) Front Panel Screws (x 4):
Remove and reuse these screws when mounting to the 998-6000-003 Optional 1-RU Rack Panel for Two (2)
½-Rack sized enclosures. Optional panel holds two (2) interfaces side-by-side in 1-RU space.
2) Product Info:
Logo, Name, Part Number FCC and CE Marks and standard FCC disclaimer language (exciting stuff)...
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 9 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
INSTALLATION PROCEDURES
Before Installing:
 Choose a camera mounting location paying close attention to camera viewing angles, lighting conditions,
possible line of site obstructions, and checking for in-wall obstructions where the camera is to be mounted.
Always pick a mounting location that will optimize the performance of the camera.
 The CONCEAL wall mount for the PowerVIEW systems can be mounted directly to a 2-gang wall box or can
be mounted using only dry wall anchors.
RS-232 Cabling Notes:
For RS-232 cabling, use a standard Cat-5 cable with real RJ-45 connectors (568B termination) from the RS-232
‘TO CAMERA’ port on the back of the Quick-Connect DVI/HDMI SR interface to the camera’s RS-232 - IR OUT
Port. If the camera is connected to a third-party control system (such as AMX or Crestron), a DE-9F (also called a
DB-9F in some circles) to RJ-45F control adapter is supplied.
More Notes: Use of pass-thru type RJ-45 connectors is highly discouraged. The Vaddio Cat-5 wiring
standard uses pins 1, 2, 7 and 8 on both the power/video and the control Cat-5 cables. The passthrough connectors have proven to provide insufficient connectivity for these important signals. They
are OK for voice and data that use the center pins only, but not for cabling systems that use all the pins.
Installation Basics:
This camera system was specifically designed for installation on a vertical wall surface with Cat-5
cable connectivity for Video, Power and Control signaling (two Cat-5 cables are required with the
QDVI system). This cabling ideology is especially convenient when the camera location is not
anywhere near to an AC outlet. Installation is simplified in that no custom 8-Pin mini-din cables or
expensive plenum coax cables or multi-pin cables are needed and no power outlets are required
near the camera bracket. All Cat-5 cabling is routed to the head-end using with standard straight
through RJ-45 connectors (568B termination). “Pass-thru” type RJ-45 connectors should be
avoided, like standing on a ladder to wave to the OSHA inspector, which should be avoided too.
General Installation Instructions for the CONCEAL Wall Mounting System:
Step 1: Determine Camera Mount Location and Mount
After determining the optimum location of the camera system, route both (2) required Cat-5 cables from the camera
to the head-end. Test and mark the cables Power/Video and RS-232 accordingly.
Both Cat-5 cables should feed-through a 1” (25.4mm) opening (circular or
square shape) centered in the rectangular slot located on the rear flange of
the CONCEAL Wall Mount Bracket.
CONCEAL Wall
Mount Bracket:
1” Diameter Hole
Note: Please do not cut out the entire rectangular slot opening in
the wall. This will not allow the two lower wall anchors to correctly
fasten the CONCEAL bracket to the wall.
If the bracket is to be mounted on a 2-gang wall box, use the screws supplied
with the wall box cover plate to attach the CONCEAL Wall Mount Bracket. If
mounting to drywall with wall anchors, use the four (4) quality wall
anchors/screws provided.
Use a level to
level the mount.
The mounting holes are slotted and are 90° opposing to provide easy leveling.
Level the mount and place the camera on the mount. The example of the
CONCEAL mount shows a different Vaddio Camera, but the steps are identical
for the HD-22 or HD-30.
Camera aligned and attached to the CONCEAL
Wall Mount Bracket (by two 1/4”-20) screws in
the bottom of the mount).
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 10 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
Step 2: System Wiring
Follow the sample wiring diagrams for connecting the Cat-5 cables to the camera and Quick-Connect DVI/HDMI
SR Interface. Additional diagrams are available on the Vaddio website.
Connect the camera side as follows:
 Connect the Power/Video Cat-5 to the EZ POWER HD VIDEO RJ-45 jack on the back of the camera.
 Connect the RS-232 Control Cat-5 to the RS-232 IR OUT RJ-45 on the camera.
Connect the Quick-Connect DVI/HDMI-SR side as follows:
 Connect the Power/Video Cat-5 to the EZCAMERA POWER & HD VIDEO RJ-45 jack.
 Connect the RS-232 Cat-5 cable to the RS-232 ‘TO CAMERA’ RJ-45 jack and connect the controller, or
console to the RS-232 INPUT.
 The controller can be routed directly to the camera if preferred. For IR Forwarding, the RS-232 cable must be
routed through the Quick-Connect SR in order to operate correctly (see pin-out section)
 Connect the video outputs (HD-YPbPr or HDMI/DVI) to the desired video console or display.
Note: Please check all Cat-5 cables for continuity in advance of final connection. Plugging the
POWER/VIDEO Cat-5 cable into the wrong RJ-45 may cause damage to the camera system and void
the warranty!
Step 3: Secure the Camera To the CONCEAL Wall Mount Bracket
After all cables are attached to the camera, slide the camera back onto mount and insert the two 1/4”-20 screws
into the camera through the two-screw slots in the bottom of the mount. Note: Be sure to align each side of the
camera evenly for the best fit prior to tightening down the mounting screws.
Step 4: Install the CONCEAL Lower Cover Plate
Attach the CONCEAL lower cover plate. Slide the lower cover plate from front of the mounting bracket toward the
rear of the bracket. The two (2) rear locking tabs will need to be guided into position first and will lock in place as
the lower cover plate is pushed toward the rear of the mounting bracket. The two (2) front tabs will engage as the
cover is pushed back into place.
CONCEAL Lower Cover Plate
with Locking Tabs
CONCEAL Lower Cover
Plate locked in place
Step 5: Install the CONCEAL Rear Camera Cover
Install the CONCEAL rear camera cover on the mounting bracket with the supplied screw.
CONCEAL Rear Camera Cover
Completed CONCEAL Wall Mount
Camera Bracket Installation
NOTE (One more time!): Please verify that the Cat-5 cables are plugged in correctly. Plugging the
wrong cable into the wrong jack may cause confounding bewilderment (in general).
Step 6: Connect System Power
Connect the 24 VDC power supply to the Quick-Connect DVI/HDMI SR Interface and the AC plug into an AC outlet.
The Quick-Connect will power the camera via the Power/Video Cat-5 cable. The camera will “Home” to a centered
position (or stored preset home position if one is set) and will output video when it has completely booted up. The
PowerVIEW is now ready for control information from a controller or IR Remote Commander.
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 11 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
Boot Order Notes: When using a joystick controller or external control system, in order to
ensure proper continuity of camera control, the RS-232 controller should be powered-on after
the camera. In most, if not all cases, the camera needs to be on and running in order for
communication to take place between the camera and controller. When plugging a new camera
into a RS-232 controller/joystick that has already been powered up, a system reboot or camera
rescan may be necessary to find the camera.
Image: Basic Connectivity Example of the HD-22 or HD-30
Camera Connected to Quick-Connect DVI/HDMI-SR Interface, ProductionVIEW™ Precision Camera Controller
and Monitor.
Rear View of HD-22 or
HD-30 PTZ Camera
CONCEAL Mount
Not Shown
EZ-POWER VIDEO
Cat-5e (orange to
orange)
Video, Power and Control on two
Cat-5/5e/6 cables up to 100’ (30.48m)
RS-232 Cat-5e
(blue to blue)
* The Recessed Color Space
Conversion Switch enables the
use of either HDMI (YCbCr) or
DVI-D (sRGB) color space for
added flexibility.
Quick-Connect
DVI/HDMI SR Interface
← HSDS
Video
Power
→
HD Video
YPbPr
24VDC, 2.0 A
Power Supply
RS-232
Cat-5
* HDMI Video
(w/cable adapter)
HD MV Multi-Viewer Monitor
and Console (not shown)
Simulated Video Feed
ProductionVIEW™
Precision Camera Controller
.
HD Monitor (Simulated Video)
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 12 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
DAISY CHAIN CONFIGURATIONS
In some cases, daisy chain control situations just can’t be avoided. Because of this, Vaddio added “Daisy Chain
Control Emulation” or DCCE™ to the Quick-Connect DVI/HDMI SR Interface in order to use the ClearVIEW or
PowerVIEW series cameras daisy chain control situations. Hardware codecs (Cisco & Polycom) that control
cameras using a daisy chain control topology are prime examples of where DCCE can be used.
1) For daisy chain control, first complete steps above, since all the cabling between the camera and the QuickConnect DVI/HDMI Interface is the same.
2) Instead of running a control cable from the 1st camera to the 2nd camera to form a daisy chain, run a Cat-5e
patch cable from the 1st Quick-Connect DVI/HDMI Interface’s RS-232 CONTROL - DAISY CHAIN RJ-45 jack,
to the 2nd Quick-Connect DVI-HDMI SR Interface’s RS-232 CONTROL INPUT RJ-45 jack.
3) Within the modified VISCA® protocol that the codec and the ClearVIEW and PowerVIEW cameras use, the 1st
in the chain will set up as Camera #1, the second will set up as Camera #2 in the chain, allowing the controller
or hardware codec’s IR remote (using the IR Forwarding Feature) to select which camera it will switch to and
which to control.
4)
In the case of Cisco codecs, use the IR Modulated output of the Quick-Connect and a Xantech IR emitter
(282D or 283D) and attach the emitter to the front panel of the codec (in front of the IR receiver).
5) Polycom codecs with IR receivers can connect the IR feed-through the same way as the Cisco, but do not use
daisy chain control. Several Polycom codecs can also be connected directly with the non-modulated signal to
the codec’s IR signal input port.
Basic Daisy Chain Connectivity:
RS-232
To
Camera #1
RS-232
To
Camera #2
Daisy Chain Port Out
RS-232 Control IN
RS-232
RS-232 from Codec
Single Control Port
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 13 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
COMPLIANCE AND CE DECLARATION OF CONFORMITY - POWERVIEW HD-22 AND HD30
Compliance testing was performed to the following regulations:







FCC Part 15 (15.107, 15.109), Subpart B
ICES-003, Issue 4: 2004
EN 55022 A: 2006 + A1: 2007
KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002)
KN22 2008 (CISPR 22: 2006)
EMC Directive 2004/108/EC
EN 55024: A2: 2003
Class A
Class A
Class A
Class A
Class A
Class A
Class A
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his/her own
expense.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device
must accept any interference including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the
user’s authority to operate this equipment.
ICES-003 Compliance
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le
ministère des Communications du Canada.
European Compliance
This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures.
Standard(s) To Which Conformity Is Declared:
EMC Directive 2004/108/EC
EN 55022 A: 2006 + A1: 2007(CISPR 22:2005/A1:2005)
EN 55024: 1998 + Amendments A1: 2001 + A2: 2003







EN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001
EN 61000-4-3: 2006 + A1: 2008
EN 61000-4-4: 2004 + Corrigendum 2006
EN 61000-4-5: 2006
EN 61000-4-6: 2009
EN 61000-4-8: 2010
EN 61000-4-11: 2004
KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002)







EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
IEC 60950-1:2005 (2nd Edition); Am 1:2009
EN 60950-1:2006+A11:2009+A1:2010+A12:2011
Conducted and Radiated Emissions
Immunity
Electrostatic Discharge
Radiated Immunity
Electrical Fast Transients
Surge Immunity
Conducted Immunity
Power Frequency Magnetic Field
Voltage Dips, Interrupts and Fluctuations
IT Immunity Characteristics
Electrostatic Discharge
Radiated Immunity
Electrical Fast Transients
Surge Immunity
Conducted Immunity
Power Frequency Magnetic Field
Voltage Dips, Interrupts and Fluctuations
Safety
Safety
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 14 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
COMPLIANCE AND CE DECLARATION OF CONFORMITY - QUICK-CONNECT DVI/HDMI SR INTERFACE
Compliance testing was performed to the following regulations:




FCC Part 15, Subpart B
ICES-003, Issue 4: 2004
European Standard EN 55022 A: 2006 + A1: 2007(CISPR 22:2005/A1:2005)
EMC Directive 2004/108/EC
Class A
Class A
Class A
Class A
FCC Part 15 Compliance
 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15, Subpart
B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his/her own expense.
 Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must
accept any interference including interference that may cause undesired operation of the device.
 Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the user’s
authority to operate this equipment.
ICES-003 Compliance
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le ministère des
Communications du Canada.
European Compliance
This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and Immunity and
meets the requirements for a Class A digital device. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Ferrite cylinders are included in order to the Quick-Connect DVI/HDMI SR Interface to strictly comply with the European
Community EMC Directives compliance. Use these ferrites to ensure the elimination of possible EMI interference from cell
phones and AC motors.
Standard(s) To Which Conformity Is Declared:
EMC Directive 2004/108/EC
EN 55022 A: 2006 + A1 2007 (CISPR 22:2005/A1:2005) Conducted and Radiated Emissions
EN 55024: 1998 + Amendments A1: 2001 + A2: 2003 - Electromagnetic Compatibility - Immunity
EN 61000-4-2
Electrostatic Discharge
EN 61000-4-3
Radiated Immunity
EN 61000-4-4
Electrical Fast Transients
EN 61000-4-5
Surge Immunity
EN 61000-4-6
Conducted Immunity
EN 61000-4-8
Power Frequency Magnetic Field
EN 61000-4-11
Voltage Dips, Interrupts and Fluctuations
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 15 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
WARRANTY INFORMATION
(See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details):
Hardware* Warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured products. Vaddio warrants
its manufactured products against defects in materials and workmanship for a period of two years from the day of purchase, to
the original purchaser, if Vaddio receives notice of such defects during the warranty. Vaddio, at its option, will repair or replace
products that prove to be defective. Vaddio manufactures its hardware products from parts and components that are new or
equivalent to new in accordance with industry standard practices.
Exclusions: The above warranty shall not apply to defects resulting from improper or inadequate maintenance by the customer,
customers applied software or interfacing, unauthorized modifications or misuse, mishandling, operation outside the normal
environmental specifications for the product, use of the incorrect power supply, modified power supply or improper site operation
and maintenance. OEM products and products manufactured by other companies are excluded and are covered by the
manufacturer’s warranty.
Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under
warranty. If the product is out of warranty, Vaddio will test then repair the product or products. The cost of parts and labor
charge will be estimated by a technician and confirmed by the customer prior to repair. All components must be returned for
testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.
Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs and/or
replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at
support@vaddio.com or online at vaddio.com.
Return Material Authorization (RMA) Number: Before returning a product for repair or replacement request an RMA from
Vaddio’s technical support. Provide the technician with a return phone number, e-mail address, shipping address, product serial
numbers and original purchase order number. Describe the reason for repairs or returns as well as the date of purchase. See
the General RMA Terms and Procedures section for more information. RMA’s are valid for 30 days and will be issued to Vaddio
dealers only. End users must return products through Vaddio dealers. Include the assigned RMA number in all correspondence
with Vaddio. Write the assigned RMA number clearly on the shipping label of the box when returning the product. All products
returned for credit are subject to a restocking charge without exception.
Voided Warranty: The warranty does not apply if the original serial number has been removed or if the product has been
disassembled or damaged through misuse, accident, modifications, use of incorrect power supply, use of a modified power
supply or unauthorized repair.
Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any
responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and insurance
charges for all items under warranty but will not assume responsibility for loss and/or damage by the outbound freight carrier.
If the return shipment appears damaged, retain the original boxes and packing material for inspection by the carrier. Contact
your carrier immediately.
Products not under Warranty: Payment arrangements are required before outbound shipment for all out of warranty products.
*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry standard practices.
Other General Information:
Care and Cleaning
Do not attempt to take this product apart at any time. There are no user-serviceable components inside.

Do not spill liquids in the product

Keep this device away from food and liquid

For smears or smudges on the product, wipe with a clean, soft cloth

Use a lens cleaner on the lens…

Do not use any abrasive chemicals.
Operating and Storage Conditions:
Do not store or operate the device under the following conditions:

Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)

High humidity, condensing or wet environments

In inclement weather

In swimming pools or drainage culverts (lack of light)

Dry environments with an excess of static discharge

In an aluminum canoe (moisture issue)

Under severe vibration
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 16 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
GENERAL SPECIFICATIONS
Camera
Part Numbers
PowerVIEW HD-22 PTZ
PowerVIEW HD-30 PTZ
999-6960-000 (North America)
999-6970-000 (North America)
999-6960-001 (Int’l)
999-6970-001 (Int’l)
Zoom
22X Optical Zoom
30X Optical Zoom
Field of View
Horizontal: 65.2º Wide End to 3.1º Tele
Horizontal: 65º Wide End to 2.2º Tele
(16:9 Aspect Ratio)
(16:9 Aspect Ratio)
Lens Focal Length
f=4.3 mm to 94.6 mm / F1.6 - F4.7
f=4.3mm to 129.0 mm / F1.6- F4.7
Image Sensor
1/2.8-Type MOS, 2.2 Megapixel, Progressive Scan
Minimum Illumination
Color: 0.4 lux (F1.6, 1/30 sec, 50 IRE, Gain: High),
B/W: 0.04 lux (F1.6, 1/30 sec, 50 IRE, Gain: High)
Video Resolutions
HD: 1080p/59.94, 1080p/50, 1080p/29.97/25, 1080i/59.94, 1080i/50, 720p/59.94, 720p/50
SD: 480p/59.97 and 576p/50
Video Output Formats
HDMI (YCbCr for HDMI and sRGB for DVI), Analog Component (YPbPr)
HSDS (Power, Differential HD Video & R$S-232 Control)
Signal to Noise Ratio
> 50 dB (AGC: Off)
Quick-Connect DVI/HDMI SR
PowerVIEW HD-22/30
Quick-Connect
Part Number 998-1105-018
Pan Range
Pan: +170 degrees to -170 degrees
Tilt: +90 degrees to -30 degrees
Preset Positions
16 (internal), 6 recalled via Vaddio IR Remote Commander
Image Control
Red & Blue Gain, Detail, Chroma, Gamma, Pedestal, Iris, and Gain
(Controls available through RS-232 control and Quick-Connect CCU and Slot Card)
Tally Light
Available through RS-232 Control
HD Video Select
16-Position Rotary Switch: Used to set HD Video Resolution Output
Camera Settings
10-Position Dip Switch: Settings for IR Select, Baud Rate 9600, Image Flip, Unpublished
Functions
Accessory Slot Cards
EZIM CCU Slot Card PN# 999-6900-006 - For Use with Quick-Connect Universal CCU Only
Dimensions/Weight
7.81” (198.37mm) H x 6.67” (169.42mm) W x 7.057” (179.25. mm) D / 5.6 lbs. (2.630835643 kg.)
Quick-Connect DVI/HDMI-SR (Short Range) Interface
Connectors





Power Connector: 5.5mm OD, 2.5mm ID coaxial connector
RJ-45: Four (4) Control IN, Control OUT, Daisy Chain OUT, EZCamera Power Video Port
Video Output: DE-15 connector for HD Analog Component (Y,PB,PR) video only (No SD Support)
IR Output: Transmits modulated or non-modulated IR signals received from the HD-19 IR receiver
Video Outputs: DVI-D (Female - Single Link) or HDMI with adapter cable (using the Recessed Color
Space Conversion Switch) , DE-15F (High Density D-Sub 15-Pin F) for HD YPbPr
Cat-5 Cable Distance
Up to 100’ (30.5m)
Power Supply
24 VDC, 2.0 Amp Switching Power Supply
Dimensions / Weight
1.6” (40.64mm ) H x 8” (203.2mm) W x 6.751” (171.45mm) D, ½-Rack Size / 1.21 lbs.
(0.548846804 kg)
Accessory Options
1-RU Rack Mount Panel for two (2) units (side by side): P/N: 998-6000-003
1m (3.3’) DVI-D Male to HDMI Male P/N: 440-5643-001
3m (10’) DVI-D Male to HDMI Male P/N: 440-5643-003
CONCEAL Wall Mounting System
Dimensions
5.125” H x 6.75” W x 10” D (13 cm x 17.15 cm x 25.4 cm)
Weight
Approx. 2.4 lbs. (1.1kg)
Moon in Front Page Header: Umbriel - Moon of the planet Uranus (tinted blue to expose detail).
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 17 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
APPENDIX 1: PIN-OUTS FOR THE HD-22/30 CAMERA
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
YPbPr
Pr
Y
Pb
Pr GND
Y GND
Pb GND
GND
-
EZ-POWER Video RJ-45 Connector Pin-outs
Important Note: The EZ POWER HD VIDEO RJ-45 Connector is for use with the Quick-Connect SR,
Quick-Connect DVI/HDMI SR and Quick-Connect USB Interfaces ONLY (568B Wiring Standard). The
video signals are differential (HSDS™) and can only be received by the interfaces above.
Pin
1
2
3
4
5
6
7
8
Signal
Power+
PowerY+
PB+
PB YPR+
PR-
EZ-POWER
VIDEO
12345678
RS-232, IR OUT on Camera HD-22/30 - RJ-45
Pin #
Function
Pin - 1
Pin - 2
Pin - 3
Pin - 4
Pin - 5
Pin - 6
Pin - 7
Pin - 8
N/A
N/A
N/A
IR Output (Diff Signal to Quick-Connect DVI/HDMI-SR)
IR Ground (Diff Signal to Quick-Connect DVI/HDMI-SR)
Digital GND
RXD (from TXD of control source)
TXD (to RXD of control source)
RS-232
IR OUT
12345678
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 18 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
Drawing: PowerVIEW HD-22/30 Camera Dimensions
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 19 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
COMMUNICATION SPECIFICATION
Communication Speed: 9600 bps (default)
Start bit: 1
Stop bit: 1
Data bits: 8
Parity: None
No Flow control
12345678
Pin #
Pin - 1
Pin - 2
Pin - 3
Pin - 4
Pin - 5
Pin - 6
Pin - 7
Pin - 8
Function
N/A
N/A
N/A
IR Output (Diff Signal to Quick-Connect DVI/HDMI-SR)
IR Ground (Diff Signal to Quick-Connect DVI/HDMI-SR)
Digital GND
RXD (from TXD of control source)
TXD (to RXD of control source)
NOTE: The Vaddio PowerVIEW HD-22 and 30Control Protocol is similar, but not identical to, the Sony® VISCA™
command set in order to be compatible with several popular control devices. Not all VISCA commands are
supported and there are many HD-22/30 specific commands in the following Command and Inquiry Lists.
HD-22/30 Command List (1/2)
Command Set
Address Set
IF_Clear
Command Cancel
CAM_Power
CAM_Zoom
CAM_Focus
CAM_WB
CAM_RGain
CAM_BGain
CAM_AE
CAM_Iris
CAM_Gain
CAM_Backlight
CAM_Aperture
Command
Broadcast
Broadcast
On
Off(Standby)
Stop
Tele(Standard)
Wide(Standard)
Tele(Variable)
Wide(Variable)
Direct
Stop
Far(Standard)
Near(Standard)
Far(Variable)
Near(Variable)
AutoFocus
ManualFocus
Auto/Manual
Direct
Auto
Indoor
Outdoor
One Push WB
Manual
Fluorescent
One Push Trigger
Reset
Up
Down
Direct
Reset
Up
Down
Direct
Full Auto
Manual
Reset
Up
Down
Direct
Reset
Up
Down
Direct
On
Off
Reset
Up
Down
Direct
Command Packet
88 30 01 FF
88 01 00 01 FF
8x 2p FF
8x 01 04 00 02 FF
8x 01 04 00 03 FF
8x 01 04 07 00 FF
8x 01 04 07 02 FF
8x 01 04 07 03 FF
8x 01 04 07 2p FF
8x 01 04 07 3p FF
8x 01 04 47 00 0p 0q 0r FF
8x 01 04 08 00 FF
8x 01 04 08 02 FF
8x 01 04 08 03 FF
8x 01 04 08 2p FF
8x 01 04 08 3p FF
8x 01 04 38 02 FF
8x 01 04 38 03 FF
8x 01 04 38 10 FF
8x 01 04 48 0p 0q 0r 0s FF
8x 01 04 35 00 FF
8x 01 04 35 01 FF
8x 01 04 35 02 FF
8x 01 04 35 03 FF
8x 01 04 35 05 FF
8x 01 04 35 06 FF
8x 01 04 10 05 FF
8x 01 04 03 00 FF
8x 01 04 03 02 FF
8x 01 04 03 03 FF
8x 01 04 43 00 00 0p 0q FF
8x 01 04 04 00 FF
8x 01 04 04 02 FF
8x 01 04 04 03 FF
8x 01 04 44 00 00 0p 0q FF
8x 01 04 39 00 FF
8x 01 04 39 03 FF
8x 01 04 0B 00 FF
8x 01 04 0B 02 FF
8x 01 04 0B 03 FF
8x 01 04 4B 00 00 0p 0q FF
8x 01 04 0C 00 FF
8x 01 04 0C 02 FF
8x 01 04 0C 03 FF
8x 01 04 4C 00 00 0p 0q FF
8x 01 04 33 02 FF
8x 01 04 33 03 FF
8x 01 04 02 00 FF
8x 01 04 02 02 FF
8x 01 04 02 03 FF
8x 01 04 42 00 00 0p 0q FF
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Comments
Address Set (Daisy chain)
IF Clear
p:socket number(1,2)
Power On/Off
p:(1-Slow to 4-Fast)
p:(1-Slow to 4-Fast)
pqr: Zoom Position*
p:(1-Slow to 4-Fast)
p:(1-Slow to 4-Fast)
pqrs: Focus position(0-0x438)*
Normal Auto (Auto Tracing WB)
Indoor Mode (Color Temp 3200K)
Outdoor Mode (Color Temp 5600K)
One Push White Balance Mode
Manual White Balance
Fluorescent(Color Temp 4200K)
One Push WB Trigger
pq:00-ff
pq:00-ff
Auto Exposure Mode
Manual Control Mode
pq(0x00-0xFF)
pq(0x00-0xFF)
pq(0x00-0x3F)
Page 20 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
HD-22/30 Command List (2/2)
Command Set
CAM_Memory
CAM_IDWrite
CAM_LR_Reverse
CAM_Freeze
CAM_PictureEffect
Pan-tiltDrive
Tally
Preset Pan Speed
Motor Config
BLK.Enhance
GMA.Enhance
CRM.Enhance
DIS.Enhance
DNR.Enhance
AGC.Enhance
CAM_ICR
Command
Reset
Set
Recall
On
Off
On
Off
Color
B&W
Up
Down
Left
Right
UpLeft
UpRight
DownLeft
DownRight
Stop
Absolute Position
Command Packet
8x 01 04 3F 00 0p FF
8x 01 04 3F 01 0p FF
8x 01 04 3F 02 0p FF
8x 01 04 22 0p 0q 0r 0s FF
8x 01 04 61 02 FF
8x 01 04 61 03 FF
8x 01 04 62 02 FF
8x 01 04 62 03 FF
8x 01 04 63 00 FF
8x 01 04 63 04 FF
8x 01 06 01 VV WW 03 01 FF
8x 01 06 01 VV WW 03 02 FF
8x 01 06 01 VV WW 01 03 FF
8x 01 06 01 VV WW 02 03 FF
8x 01 06 01 VV WW 01 01 FF
8x 01 06 01 VV WW 02 01 FF
8x 01 06 01 VV WW 01 02 FF
8x 01 06 01 VV WW 02 02 FF
8x 01 06 01 VV WW 03 03 FF
8x 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
Comments
p:Memory No(=0-0xF)
pqrs:0x0000 – 0xFFFF
Mirror (Horizontal) on
Mirror (Horizontal) off
Still image on
VV: Pan Speed (0x01-0x18)
WW: Tilt Speed(0x01-0x14)
YYYY: Pan Position**
ZZZZ: Tilt Position**
Home
Reset
On
Off
Pan/Tilt/Zoom Speed
8x 01 06 04 FF
8x 01 06 05 FF
8x 01 7E 01 0A 00 02 FF
8x 01 7E 01 0A 00 03 FF
8x 01 7E 01 0B WW SS ZZ FF
Hard Motor Stops
Soft Motor Stops
Pedestal
Gamma
Chroma
8x 01 7E 01 70 00 00 FF
8x 01 7E 01 70 00 01 FF
8x 01 7E 53 00 00 0p 0q FF
8x 01 7E 54 00 00 0p 0q FF
8x 01 7E 55 00 00 0p 0q FF
Pq: Pedestal(0x00-0xFF)
pq: Gamma (0x00-0x03)
pq: Chroma (0x00-0xFF)
Digital Image
Stabilizer
Digital Noise
Reduction
AGC Mode
8x 01 7E 57 02 FF
8x 01 7E 57 03 FF
8x 01 7E 58 02 FF
8x 01 7E 58 03 FF
8x 01 7E 59 00 FF
8x 01 7E 59 01 FF
8x 01 7E 59 02 FF
8x 01 7E 59 03 FF
8x 01 7E 59 04 FF
8x 01 7E 59 05 FF
8x 01 7E 59 06 FF
8x 01 7E 59 07 FF
8x 01 7E 59 00 0p FF
On
Off
On
Off
Off Manual AGC Gain (0dB)
Low
Medium
High
Low1
Low2
Med1
High1
Off p: Manual AGC Gain(1-0x0e)***
ICR On
ICR Off
8x 01 04 01 02 FF
8x 01 04 01 03 FF
ICR On – Cut filter out B&W
ICR Off – Cut filter in Color
WW: Pan Speed (0x01-0x18)
SS:Tilt Speed(0x01-0x14)
ZZ:Zoom Speed(0-7);
*Zoom and Focus Data:
CAM_Zoom: Range (0x000–0xA23/0xA73), HD22: 0xA23 (22x Zoom), HD30: 0xA73 (30x Zoom)
CAM_Focus: Range (0x000-0x438) dependent on Zoom Position
**Additional Information:
Pan Range: 8044 – 7FBC (-32,700 to +32,700)
Tilt Range: E891 – 4C2B (-5,999 to +19,499)
Actual Pan/Tilt ranges defined in Inquiry list
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 21 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
HD-22/30 Inquiry List (1/1)
Inquiry Command
CAM_PowerInq
Command
8x 09 04 00 FF
CAM_ICRModeInq
8x 09 04 01 FF
CAM_BacklightModeInq
8x 09 04 33 FF
CAM_WBModeInq
81 09 04 35 FF
CAM_AEModeInq
8x 09 04 39 FF
CAM_LR_Reverse
8x 09 04 61 FF
CAM_Freeze
8x 09 04 62 FF
CAM_PictureEffect
8x 09 04 63 FF
CAM_MemoryInq
CAM_IDInq
CAM_ApertureInq
CAM_RGain
CAM_BGain
CAM_ZoomPosInq
CAM_FocusPosInq
CAM_FocusModeInq
8x 09 04 3F FF
8x 09 04 22 FF
8x 09 04 42 FF
8x 09 04 43 FF
8x 09 04 44 FF
8x 09 04 47 FF
8x 09 04 48 FF
8x 09 04 38 FF
CAM_Iris
CAM_Gain
IR_ReceiveInq
8x 09 04 4B FF
8x 09 04 4C FF
8x 09 06 08 FF
Pan-TiltMaxSpeedInq
8x 09 06 11 FF
Response Packet
y0 50 02 FF
y0 50 03 FF
y0 50 02 FF
y0 50 03 FF
y0 50 02 FF
y0 50 03 FF
y0 50 00 FF
y0 50 01 FF
y0 50 02 FF
y0 50 03 FF
y0 50 05 FF
y0 50 06 FF
y0 50 00 FF
y0 50 03 FF
y0 50 02 FF
y0 50 03 FF
y0 50 02 FF
y0 50 03 FF
y0 50 00 FF
y0 50 04 FF
y0 50 0p FF
y0 50 0p 0q 0r 0s FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
y0 50 0p 0q 0r 0s FF
y0 50 0p 0q 0r 0s FF
y0 50 02 FF
y0 50 03 FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
y0 50 02 FF
y0 50 03 FF
y0 50 pp qq FF
Pan-tiltPositionInq
8x 09 06 12 FF
FF y0 50 0p 0p 0p 0p 0q 0q 0q 0q FF
TallyInq
8x 09 7E 01 0A FF
PresetSpeedInq
8x 09 7E 01 0B FF
y0 50 02 FF
y0 50 03 FF
y0 50 pp qq rr FF
Motor Config
8x 09 7E 01 70 FF
BLK.Enhance
GMA.Enhance
CRM.Enhance
KNE.Enhance
8x 09 7E 53 FF
8x 09 7E 54 FF
8x 09 7E 55 FF
No support
DIS.Enhance
8x 09 7E 57 FF
DNR.Enhance
8x 09 7E 58 FF
AGC.Enhance
8x 09 7E 59 FF
8x 09 7E 59 00 FF
y0 50 00 FF
y0 50 01 FF
y0 50 00 00 0p 0q FF
y0 50 00 00 00 0p FF
y0 50 00 00 0p 0q FF
No Support
Comments
On
Off(Standby)
On - ICR filter Out
Off – ICR filter In
On
Off
Auto
Indoor
Outdoor
One Push WB
Manual
Fluorescent
Auto Exposure Mode
Manual Control Mode
On
Off
On
Off
Off
B&W
p:Preset 0-0xf
pqrs:0x0000 – 0xFFFF
Pq:x00-0x3F
pq:000-0ff
pq:000-0ff
pqr: 0-0x6B3
pqrs: Focus Position
Auto
Manual
pq(0x00-0xFF)
pq(0x00-0x24)
On
Off
pp:Pan 0x01-0x18
qq:Tilt
0x01-0x14
pppp: Pan 0x8044-0x7FB2
qqqq: Tilt 0xE890-0x4C2C
On
Off
pp:Pan 0x01-0x18
qq:Tilt
0x01-0x14
rr:Zoom 0x00-0x07
Hard Motor Stops
Soft Motor Stops
pq: Pedestal(0x00-0xFF)
p: Gamma (0x00-0x03)
p: Chroma (0x00-0xFF)
Knee
y0 50 02 FF
y0 50 03 FF
y0 50 02 FF
y0 50 03 FF
y0 50 00 FF
y0 50 01 FF
y0 50 02 FF
y0 50 03 FF
y0 50 04 FF
y0 50 05 FF
y0 50 06 FF
y0 50 07 FF
y0 50 0p FF
On
Off
On
Off
Off Manual AGC Gain(0dB)
Low
Medium
High
Low1
Low2
Med1
High1
Off p: Manual AGC Gain(0-0x0e)***
***Manual AGC Gain: 0:0dB, 1:3dB, 2:6dB, 3:9dB, 4:12dB, 5:15dB, 6:18dB, 7:21dB, 8:24dB, 9:27dB, 10:30dB, 11:33dB,
12:36dB, 13:39dB & 14:42dB
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 22 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
Inside Rear Cover - Mostly Blank
PowerVIEW HD-22 and HD-30 QDVI Cameras Systems - Document Number 342-0644 Rev D
Page 23 of 24
PowerVIEW HD-22 and HD-30 QDVI Systems
Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 ▪ vaddio.com
©2015 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without
notice or obligation. Vaddio, PowerVIEW, ProductionVIEW, EZCamera, Quick-Connect, CONCEAL, DCCE and HSDS are trademarks of Vaddio. All other trademarks
are
property of their
respective
owners.
Document
Number
342-0644
Rev D, SD:
68670.0342-0644 Rev D
PowerVIEW
HD-22
and HD-30
QDVI
Cameras
Systems
- Document
Number
Page 24 of 24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising