Wireless Powerlink II Receiver Set Active Installation Guide

Wireless Powerlink II Receiver Set Active Installation Guide
Wireless Powerlink
II Receiver Set Active
Installation Guide
Contents
General
1
WirelessPowerlink
Page 2
Package Contents
Installation
System Description
Safety Instructions
Page 3
Disposal of Old Electrical Devices
Page 4
"Pairing Function"
Page 5
Connecting the Devices
Page 6
Assembly Instructions / Placement
Page 7
Compatibility with Bang & Olufsen
Devices
®
Page 8
WirelessPowerlink for Surround Systems
WirelessPowerlink in Stereo Mode
Page 9
WirelessPowerlink for your Sub-woofer
Technical Data
General
Page 10
Connections
Housing
© 2011 BOSSCOM DENMARK
All names, logos, etc. are registered trademarks of the companies listed in this
brochure.
The information in this manual is subject to change without notice. All rights
Reserved.
General
2
Dear Customer,
®
Thank you for choosing this wireless Bang & Olufsen compatible Powerlink
radio transmission system. This installation guide will help you to properly
integrate the unit into your audio system. With years of expertise, we want to
bring the benefits of the latest technology into your living room.
WirelessPowerlink
The WirelessPowerlink System was specifically developed for your Bang &
®
Olufsen system and provides signal transmission from the system to the
speakers, wherever a wired connection is not possible or simply too expensive.
®
The TV Station on your Bang & Olufsen TV for example, and the receivers of
the rear speakers are constantly connected via radio - this means you can enjoy
wireless surround sound in absolute CD-quality.
The automatic frequency change to the maximum transmission reliability, results
in an insignificant latency between the wired and wireless connected speakers which creates a slight hall effect. In case there is no signal available at the
transmitter - because the system is turned off or the sound is muted - the
speakers will also go into standby mode - just like it would with a cable
connection.
Package Contents
Receiver Active
(Receiver)
2
Stereo Transmitter
(Transmitter)
Power Cord
(for
transmitter)
Power Link
cable (for
transmitter)
Paper clips (for
the pairing of
transmitter and
receiver)
General
3
Safety Instructions
To ensure best performance, please read these instructions carefully. Keep
them in a safe place for future reference.
Install the equipment in a well-ventilated, cool, dry, clean environment - away
from direct sunlight, heat sources, vibration, dust, moisture and/or cold.
Place the unit away from other electrical devices, motors, or transformers to
avoid humming sounds.
Do not expose the equipment to sudden temperature changes from cold to hot,
and do not place it in places with high humidity (e.g. in a room with a humidifier) to
prevent the formation of condensation inside the devices, which could cause
electric shock, fire, damage to the devices and/or accidents with injuries.
Do not place the devices in locations where any solid objects could fall into the
device or liquid splashes may be spilled on/into the device. Do NOT place the
following items on the device:
- Other components, as they can cause damage and/or discoloration to the
surface of the devices.
- Burning objects (such as candles), as they may cause fire, damage to the
device and/or injuries.
- Containers with liquid, as they can tip over and liquid can enter the devices,
which can cause electrical shock or damage to the device.
Do not cover the devices with newspaper, tablecloth, curtains, etc., in order to
prevent heat accumulation. If the temperature inside the devices rises rapidly,
this may result in fires, damage to the devices and/or injuries.
Do not operate the devices in a tilted position. This can lead to overheating and
damage the device.
Do not apply force in the operation of buttons and/or cables. Always grasp the
plug, if you disconnect the power cord and/or the adapter from the wall outlet.
Never pull the cord.
Do not try to clean this device with chemical solvents because they may
damage the housing. Clean only with a clean, dry cloth.
General
The devices may only be operated with the prescribed voltage. Operating the
device with a higher voltage than specified, is dangerous and can cause fire,
damage to the device and /or injuries.
ip media systems GmbH is not responsible for any damage resulting from the
operation of the device with a voltage other than specified.
Do not attempt to modify or repair these devices yourself. Please contact
your specialty retailer if service is required. The housing may not be opened
under any circumstances.
If the devices are not going to be used for long periods of time (e.g. vacation),
disconnect the power cord from the wall outlets.
In case of malfunction, carry out the pairing function again (see page 5). Should
the malfunction persist, contact your local specialty retailer, or submit an email
to support@bosscom.com.
Before moving this device, unplug the power cord from the wall outlet.
Disposal of Old Electrical Devices
If this symbol is found on the products, packaging and/or
accompanying documents, used electrical devices should not be
disposed of with normal household waste.
In accordance with your national legislation and the Directives 2002/96/EC, take
your old electronic devices to the appropriate collection sites, for disposal, retreatment and reuse.
By properly disposing of electrical appliances you help to protect valuable
resources and prevent possible negative effects on human health and the
environment that might otherwise arise from inappropriate waste disposal.
For more information about collection and recycling of old electronic devices,
please contact your local city or municipal administration, your waste disposal
service or the dealer of the product.
[Information on disposal in countries outside the European Union] This
symbol is only valid within the European Union. If you wish to discard such
devices, please contact your local authorities or dealer to inquire about the
proper disposal method.
4
Installation
5
Pairing Function
The receiver must be registered with the transmitter on location. The following
steps are necessary for the registration:
1. Both units must be connected to a power source - the yellow Status LED (left
hole) lights up and the green LED (middle hole) blinks every second.
CAUTION:
Do NOT connect the
devices with the
Power Link-Source
and the speakers
yet!
Receiver
Transmitter
1.
2. Using the provided paper clips, press and hold the buttons in the right hole of
the transmitter and the first receiver for about 5 seconds, until the green signal
LED (in the middle hole)
of the transmitter
begins to flash quickly.
Releasing the buttons
starts the pairing
function
This process
may take up to
4 minutes.
It is completed
once the signal
LED begins to
blink every second.
2.
The same registration procedure must be followed for the second receiver.
3. Afterward, all devices must be unplugged.
Installation
6
Connecting the Devices
4. Connect the transmitter on the PL IN
socket to the Powerlink output of your Bang
®
& Olufsen device, with the supplied
Powerlink cable. Then connect it to the
power supply (power cord also included).
Transmitter
to the Powerlink
source
4.
5. Use a Powerlink cable to connect the receiver to the PL OUT socket and the
®
permanently connected power cord to connect it with your Bang & Olufsen
speakers (Powerlink cable included with
your speakers).
Then connect the receiver to the power supply
(Power cord also included with your speakers).
Receiver
5.
to speakers
The status LED on your speakers should now light up red.
6. The installation is now complete. You can activate the Powerlink source on low
volume - the status LED on your speakers will light green and you will enjoy the
®
sound of your Bang & Olufsen device in CD-quality.
Installation
7
Assembly Instructions / Placement
The logo on the side of the receiver and the transmitter should always be visible,
to achieve the best possible transmission quality. Also make sure that the devices
are not placed in the immediate vicinity of antenna cables - this can cause static
noise.
CORRECT:
Lying flat on
the side with
the type plate
- the side with
the logo is
visible
CORRECT:
Lying on the
narrow side
If the device is going to be attached to the wall with tape (e.g. Velcro), the side
with the logo must also be visible.
In no case should the device be placed as illustrated below.
WRONG:
Lying flat on
the side with
the
logo
facing down
In this case the metal blank faces upwards and thus partially shields the antenna,
which can lead to loss of signal quality.
System Description
Compatibility with Bang & Olufsen
8
®
Devices
The WirelessPowelink System is compatible with ALL active Bang &
®
®
Olufsen speakers other than BeoLab 5 .
WirelessPowerlink in the Surround-System
Here, the front speakers remain connected to your system via wires. Wherever a
wired connection to the rear speakers is not possible or simply too expensive, you
can expand your wired stereo system to a full surround system with Wireless
Powerlink.
PL
PL
PL
PL
PL
Note: The automatic frequency change to the maximum transmission reliability results in
an insignificant latency between the wired and wireless connected speakers - which
creates a slight hall effect. You can easily adjust this in the configuration mode of the
Dolby Surround menu. To do this, increase the distance of the wireless connected
speakers for about 6 m.
System Description
9
WirelessPowerlink in Stereo Mode
Wherever a wired connection to the rear speakers is not possible or simply too
expensive, you can extend your wired stereo system to a full surround system with
WirelessPowerlink. And if you have an outdoor party, you can simply place the
speakers on the patio and connect them to an outlet - the music will accompany you
outside.
WirelessPowerlink for your Sub-Woofer
With WirelessPowerlink as an extension you can also expand your wired stereo system
®
with a sub-woofer such as the BeoLab 2 very easily and thus increase your listening
enjoyment.
PL
PL
PL
PL
Technical Data
10
General
Transmission Mode:
Digital Radio Link
Range
Approx. 15m within the room / 50m in open field
Frequency Change:
Automatically on 34 channels
Radio Frequency:
2.4 GHz ISM band (transmitting / receiving freq.)
Modulation:
GFSK
Audio Format:
16 bit, 48 KHz Sampling Rate
Channel Separation:
> 90 dB
Signal-to-Noise Ratio:
Total Harmonic
Distortion/THD:
> 90 dB
Frequency Response:
10 Hz (-0,5dB) - 20 kHz (-1dB)
Standby Function:
After about 10 minutes without audio signal
Pairing Function:
Allocate a traffic control protocol with the device-ID
Enables parallel operation of several systems
Compatibility:
All active B & O
Power Supply:
200-240V ~ 50Hz / integrated power supply unit
THD < 0,01%
®
speakers except BeoLab 5
Connections
Receiver:
Powerlink jack 8-pin (output)
Power Connector 2-pin
Power Co (permanently connected)
Transmitter:
Powerlink jack 8-pin (input)
Power Connector 2-pin
Housing
Dimensions:
Each 171 x 72 x 34 mm (L x W x H)
Color:
Black
®
BOSSCOM,
Oldenvej 21,
3490 Kvistgård,
CVR: 25307755
Support: support@bosscom.com , Salg: sales@bosscom.com
www.bosscom.com Tlf. (+45) 70 20 00 45 , Fax (+45) 45 94 06
69
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising