operation guide fd39 wireless fish finder

operation guide fd39 wireless fish finder
FD39
WIRELESS FISH FINDER
FOR BAITBOAT USING
OPERATION GUIDE
Contents
Specification--------------------------------------------------2
Installation guide of Option A------------------------------3
Components list---------------------------------------------3
Mounting the transducer-----------------------------------4
Assembling the transmitter--------------------------------4
Charge the battery in the transmitter--------------------5
Assembling the receiver------------------------------------6
Charge the battery of the receiver------------------------7
Installation guide of Option B------------------------------8
Components list---------------------------------------------8
Mounting the transducer-----------------------------------9
Assmbling the transmitter--------------------------------10
Assembling the receiver-----------------------------------11
Charge the battery of the receiver-----------------------12
Installation guide of Option C-----------------------------13
Components list--------------------------------------------13
Mounting the transducer----------------------------------14
Assembling the transmitter-------------------------------15
Assembling the receiver-----------------------------------16
Charge the battery of the receiver-----------------------17
Operational Instruction------------------------------------18
Powering the display ON ----------------------------18
What you see on screen-----------------------------18
Accessing menu features----------------------------19
Remarks and Tips------------------------------------------24
-1-
Specification:
Display :
FSTN LCD 128Vx64H
Backlighting :
White LED
Power Requirement of Receiver:
4-AA Rechargeable Batteries
Power Requirement of Transmitter:
8-AAA Rechargeable Batteries
or DC12V
Measure Units:
Feet and meters
Sensor Frequency:
200KHz
Sensor Beam Angle:
45 degrees
Depth Range Max :
100ft (30.4M)
Depth Range Min :
2ft (0.6M)
Radio Frequency:
433MHz
Operational Range Max:
400M
Water Temperature Indicator:
Yes
Transmitter Low Battery Alarm:
Yes
Operational Temperature:
-4 to 158°F (-20—70°C)
-2-
Installation guide of Option A
Installation guide of Option A
1 Components list
2
3
4
1
5
7
6
9
10
-3-
8
11
1,
2,
3,
4,
5,
6,
7,
8,
9,
Receiver
Power cable
Antenna of receiver
4 "AA" rechargeable battery of receiver
Charge of receier
Transmitter
8"AAA" rechargeable battery of transmitter
Charger of transmitter
Antenna of transmitter(in separate package, pls ask your
retailer for details)
10, Sonar senser(transducer)
11, Tripod(optional)
2 Mounting the transducer
2.1Mounting and fixing the transducer on the bottom of the bait boat with screw or glue.
Note: Make sure the bottom of transducer to face outside and keep it to be horizontal (see
illustration)
3 Assembling the transmitter
3.1 Open the battery door and insert 8 AAA rechargeable batteries into the case as shown on
the diagram inside the battery compartment,and reattach the battery door.
-4-
3.2 Mounting and fixing the transmitter on the top of bait boat with glue or
velcro.
Note: Make sure the antenna socket face upside when mounting.
Fixing
3.3 Assembling the antenna on the transmitter (see illustration).
Screw tightly
3.4 Plug the transducer cable connector into the transmitter (see
illustration).
Plug into
4 Charge the battery in transmitter
Plug one side of charger's cable
connector into the DC socket of
transmitter, another side into the AC
power, the red indicator light and
charging is started. The indicator
turns green when power is full.
-5-
Socket for
the charger
5 Assembling the receiver
5.1 INSTALLING THE BATTERIES
When you first use the Fish Finder you will need to installing the batteries.
Slide the Battery Door, and insert 4 "AA" batteries to the battery
compartment.
Be certain to align the batteries as per the diagram within the battery
compartment.
5.2 ASSEMBLING THE ANTENNA
Plug the antenna into the socket on the back of display tightly(see
illustration)
Plug into
5.3 Connecting the Power Cable
Plug the power cable connector into the socket on the back of the display
tightly and another side to the battery compartment.
Plug into
-6-
5.4 Assembling the tripod(tripod is optional)
Screw the tripod in the screw thread socket on the bottom of battery
compartment tightly(see illustration)
Screw tightly
6 Charge the battery of receiver
Plug one side of charger's cable connector into the DC socket of receiver,
another side into the AC power, the red indicator light and charging is
started. The indicator turns green when power is full.
Warning!!! The chargers are different for transmitter and receiver.
Correct using must be requested according to the instruction on the
charger and this guide, otherwise the damage will be caused!
-7-
Installation guide of Option B
1 Components list
2
3
4
1
5
7
6
8
9
-8-
10
1,
2,
3,
4,
5,
6,
7,
8,
Receiver
Power cable
Antenna of receiver
4 "AA" rechargeable battery of receiver
Charge of receier
Transmitter
Power cable of transmitter
Antenna of transmitter(in separate package, pls ask your
retailer for details)
9, Sonar senser(transducer)
10, Tripod(optional)
2 Mounting the transducer
2.1 Remove the cover under the bait boat, put the transducer into the hole
and keep the bottom of transducer to face outside (see illustration), fixing it
by the screws.
Note: Tightening the screws.
Remove
Fixing
2.2 Fixing the transducer signal cable on the tail of the bait boat(see
illustration)
Fixing
-9-
3 Assembling the transmitter
3.1 Assembling the transmitter on the top of the bait boat (see illustration)
Note the direction
3.2 Assembling the antenna on the transmitter (see illustration)
Screw tightly
3.3 Plug the transducer cable connector into the transmitter (see
illustration)
Plug into
-10-
3.4 Connect the power cable to the transmitter and socket of boat power.
Plug into
4 Assembling the receiver
4 Assembling the receiver
When you first use the Fish Finder you will need to installing the batteries.
Slide the Battery Door, and insert 4 "AA" batteries to the battery
compartment.
Be certain to align the batteries as per the diagram within the battery
compartment.
4.2 Assembling thr antenna
Plug the antenna into the socket on the back of display tightly(see
illustration)
Plug into
-11-
4.3 Connecting the Power Cable
Plug the power cable connector into the socket on the back of the display
tightly and another side to the battery compartment.
Plug into
4.4 Assembling the tripod(tripod is optional)
Screw the tripod in the screw thread socket on the bottom of battery
compartment tightly(see illustration)
Screw tightly
5 Charge the battery of receiver
Plug one side of charger's cable
connector into the DC socket of
receiver, another side into the AC
power, the red indicator light and
charging is started. The indicator
turns green when power is full.
Warning!!! The chargers are different for transmitter and receiver.
Correct using must be requested according to the instruction on the
charger and this guide, otherwise the damage will be caused!
-12-
Installation guide of Option C
1 Components list
2
3
4
1
5
6
7
8
9
-13-
10
11
1,
2,
3,
4,
5,
6,
7,
8,
Receiver
Power cable
Antenna of receiver
4 "AA" rechargeable battery of receiver
Charge of receier
Transmitter
Power cable of transmitter
Antenna of transmitter(in separate package, pls ask your
retailer for details)
9, Sonar senser(transducer)
10, Magnet for mounting transducer
11, Tripod(optional)
2 Mounting the transducer
2.1Method I:Remove the cover under the bait boat, put the transducer into
the hole and keep the bottom of transducer to face outside (see
illustration), fixing it by the screws.
Note: Tightening the screws.
Fixing
Remove
2.2 Method II: Stick the magnet on the bottom of boat by glue (see
illustration), make the the magnet on the transducer magnetize with the
one on the boat.
Note: Make sure the magnet is kept to be horizontal with bottom of
boat when it is fixed.
Fixing
Magnet
-14-
Magnetize
2.3 Fixing the transducer signal cable on the tail of the bait boat(see
illustration)
Fixing
3 Assembling the transmitter
3.1 Assembling the transmitter on the top of the bait boat (see illustration).
3.2 Assembling the antenna on the transmitter (see illustration).
Screw tightly
3.3 Plug the transducer cable connector into the transmitter (see
illustration)
Plug into
-15-
3.4 Connect the power cable to the transmitter and socket of boat power.
Plug into
4 Assembling the receiver
4.1 Installing the batteries
When you first use the Fish Finder you will need to installing the batteries.
Slide the Battery Door, and insert 4 "AA" batteries to the battery
compartment.
Be certain to align the batteries as per the diagram within the battery
compartment.
4.2 Assembling thr antenna
Plug the antenna into the socket on the back of display tightly(see
illustration)
Plug into
-16-
4.3 Connecting the Power Cable
Plug the power cable connector into the socket on the back of the display
tightly and another side to the battery compartment.
Plug into
4.4 Assembling the tripod(tripod is optional)
Screw the tripod in the screw thread socket on the bottom of battery
compartment tightly(see illustration)
Screw tightly
5 Charge the battery of receiver
Plug one side of charger's cable
connector into the DC socket of
receiver, another side into the AC
power, the red indicator light and
charging is started. The indicator
turns green when power is full.
Warning!!! The chargers are different for transmitter and receiver.
Correct using must be requested according to the instruction on the
charger and this guide, otherwise the damage will be caused!
-17-
Operation Guide
1 POWERING ON AND OFF
Press and release POWER-MENU to power the unit on.
Press and hold POWER-MENU until the unit shuts down to power off. When
Unit powers on, the Start Up menu temporarily appears. From this menu,
select either Start-Up for on-the-water use, or Simulation for learning to
use the system with simulated sonar data.
The Start-Up menu disappears after several seconds and the Unit starts to
work.
2 WHAT YOU SEE ON SCREEN
4
3
2
1
5
6
7
8
9
1 Water Surface Line
2 Battery Strength Indicator
3 Sensitivity Indicator
4 Upper Zoom Range
5 Water Depth
6 Water Temperature
7 Bottom Contour
8 Lower Zoom Range
9 Fish Icon with Fish Depth
-18-
3 ACCESSING MENU FEATURES
A easy to use menu system
accesses unit's adjustable funtion.To
activate the menu system, press
Menu Hot Button directly to access
main menus or press POWER-MENU
repeatly to access all menus. When
the menu is on the display, use the
right and left keys to adjust the
menu. Menus automatically are
removed from the screen after
several seconds.
3.1 Light
(Setting Saved in Memory)
When you press the LIGHT , the LIGHT menu temporarily appears.
Select either OFF or ON to activate the backlight at the desired level.
NOTE: Continuous backlight operation significantly decreases battery
life on Unit Portables.
3.2 Sensitivity
(Setting Saved in Memory, 1 to 5)
When you press the SENSITIVITY , the SENSITIVITY menu temporarily
appears. Select a higher level to show smaller sonar returns on-screen, or a
lower level to remove clutter on the screen.
-19-
Adjusting Sensitivity also affects how
sonar returns are identified as Fish
Icon Symbols - more fish will be
detected at a higher lelvel setting,
fewer at a lower level setting.
3.3 Depth Range
(Setting Saved in Memory)
When you press the DEP.RANGE , the DEPTH RANGE menu temporarily
appears.
Select AUTO for the automatically setting Depth Range or manually select
8,15, 30, 60 or 120 ft. This locks the depth range to a specific setting.
NOTE: In manual operation, if the depth is greater than the depth
range setting,the bottom will not be visible on-screen. Select AUTO
to return to automatic operation.
3.4 Zoom
(Setting Saved in Memory)
When you press the ZOOM , the ZOOM menu temporarily appears.
Select ON to magnify the area around the bottom thus revealing fish and
structure close to the bottom that may not be visible in typical operation.
In Zoom, the Unit continually changes the upper and lower Depth Range to
keep area just above and below the bottom on the display.
Select OFF to return to normal operation.
-20-
3.5 Fish Alarm
(Setting Saved in Memory, Defaults to OFF)
When you press the FISH ALARM , the FISH ALARM menu temporarily
appears. Select OFF for no fish alarm, or select the ON to set the fish alarm
and activate it.
3.6 Fish Icon
(Setting Saved in Memory)
When you press the FISH ICON , the FISH ICON menu temporarily appears.
Select either OFF to view “raw” sonar returns, or
to take advantage of
Unit’s ability to identify sonar returns that are determined to be a fish. The
sonar's microcomputer is sophisticated, but it can be fooled. It can't
distinguish between fish
and other suspended objects such as trotlines, turtles,
submerged floats, air bubbles, etc.
You may see fish symbols on the screen when actually,
-21-
there are no fish. The reverse is also true
For example,when this kind of symbols/dots come out,
it is possible that is fish, but it is also possible that
is other suspended objects.
Remark:
Fish finder is to find fish under water under Ultrasonic reflections of scanning.
this fishfinder device is not a CAMERA or video recorder, which has to capture every
and each single fish shape and numbers under water such as camera effect.
so if the fish finder can fid and display the ultrasonic reflection based pointed results
on the LCD display of fishfinder then it is targeted results.
3.7 Depth Alarm
(Setting Saved in Memory)
Press POWER-MENU until the DEPTH ALARM menu appears.
Select OFF for no Depth Alarm;
select a number from 3-99' to set the alarm depth and activate it.
Audible alarm will sound when the depth is equal to or less than the setting
number.
-22-
3.8 Chart Speed
(Setting Saved in Memory, 1 to 4)
Press POWER-MENU until the CHART SPEED menu appears. Select a setting
from 1-4 to increase or decrease the chart speed, where 1 is the slowest
and 4 is the fastest chart speed.
3.9 Depth Unit
(Setting Saved in
3.10 Temperature Unit
(Setting Saved in Memory)
Press POWER-MENU until the TEMP- UNIT menu appears. Select either °C
or °F to set the unit of temperature.
3.11 Low Battery Alarm
The wireless sonar sensor has the function which can detect the
transmitter's power voltage capacity and alarm, when the sensor's power
voltage is lower than 8V, the receiver will alarm with long continuous sound
of "Bi......".
-23-
Remarks and Tips
1,Make sure the transducer was dipped into the water before
operating.
2,Make sure all plugs was connected tightly before using.
3,Continuous backlight operation significantly decreases battery life.
4, Never use a blunt to strike the sonar sensor as this may cause
damage to the sensitive internal electronics.
5, Never use the same two FD39 in the same area as this may
cause the product can not work properly due to the ultrasonic and
radio frequency interference.
6, Remove the batteries from the fish finder to prevent battery
leakage and corrosion.
7, As the depth range is from 0.6m-30.4m, the fish finder would not
work properly if the water is too deep or shallow.
8,The too much weed in the water may cause the incorrect reflect.
Note: Changes maybe made to the information in this operation
guide without obligation to notify any person of such revisions or
changes.
-24-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising