PDF Compressor

 Bestway
#58367E
110-120V~60Hz, 3.5A
QUESTIONS? PROBLEMS?
MISSING Rel
Te | |- 8 5 e Волен зн
mane ric Noe) 1
Manuals, Videos Or
Spare Parts, Please Visit
www. bestway-service.com
info@bestway-nc
For FAQ,
US
LISTED
Intertek
4006936
7 | НЫЙ
mo
A
=: я
5 i "a mE a
agg ya Ph E 5
FH A
r
fi
т
FLOWCLEAR™
Sand Filter
OWNER’S MANUAL
Email: [email protected]
www.bestway-global.com
www.bestway-service.com
5-5-004040
pr .0x28.5cm (#58367E 2000gal 3H HED IER HA 43) JS-YF-201 PR
estwa
S-S-004040
] S-S-004040/21.0x28.5cm (#58367E 2000gal E El AE 32% RAE) pr
SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
WA RN NG = TO REDUCE THE RISK OF INJURY, do not permit children to use this product unless they are closely
supervised at all times.
WA RN | NG = RISK OF ELECTRIC SHOCK - Connect only to a grounding type receptacle. This product is provided
with a ground-fault circuit-interrupter. If replacement of the plug is needed, use only identical replacement parts.
WA RN | NG = The unit is provided with a ground-fault circuit-interrupter (GFCI). To test the GFCI, push the test
button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this
manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button being pushed, a ground current
Is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump and have the problem
corrected by a qualified service representative before using.
CAU TION = To reduce the risk of electric shock the pool must be installed no closer than 6 feet (1.8 m) from any
electrical outlet. Do not place portable appliances closer than 5 feet (1.5 m) from the pool.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
WA RN N G = To reduce the risk of electric shock, replace damaged cord immediately.
WA RN N G = To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply;
provide a properly located outlet.
CAU TION = This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable
pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. A
permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for
storage.
Please examine and verify all sand filter components are present before use. Notify Bestway at the customer service address
listed on this manual for any damaged or missing parts at the time of purchase.
THERMALLY PROTECTED MOTOR. CSA ENCLOSURE 3
* FOR USE WITH SWIMMING POOLS ONLY.
. CAUTION = TO ENSURE CONTINUED PROTECTION AGAINST SHOCK HAZARD, USE ONLY IDENTICAL
REPLACEMENT PARTS WHEN SERVICING.
. WARN N G = RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A GROUNDING TYPE RECEPTACLE.
« CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS ONLY - DO NOT USE WITH PERMANENTLY -INSTALLED
POOLS.
. CAUTION - CONNECT ONLY TO GROUNDING TYPE RECEPTACLE PROTECTED BY A CLASS A GROUND
FAULT CIRCUIT INTERRUPTER.
. CAUTION FOR CONTINUED PROTECTION AGAINST POSSIBLE ELECTRIC SHOCK THIS UNIT IS TO BE
MOUNTED TO THE BASE IN ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS.
WARN NG = RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin
2) Inspect Cord Before Using - Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground
4) Do Not Touch Plug With Wet Hands
9) Double Insulated - When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
S-S-004040
[pen (#58367E 2000gal EEE in RA) pe |
Before assembling the sand filter, take a few minutes to become familiar with all the sand filter parts.
SPARE
REF.NO.| DESCRPITION QTY.|PART NO,
1 Control Valve 1 P61204
2 Pressure Gauge 1 P61138
3 Flange Clamp 2 P61205
4 Hub Cover 1 P61209
О Tank 1 P61213
6 Hub 1 P61206
7 Pollution Cartridge 1 P61211
8 Drain Washer 1 P6581
9 Drain Valve Cap 1 P6580
10 Tank Base 1 P61212
11 Garden Hose Adaptor | 1 P6614
12 Washer 5 P6029
13 Port D Cap 1 P6540
14 | Piping 1 | P6560
19 O-ring 1 P61214
16 Strainer Cover 1 P6561
С Strainer 1 P6562
18 Filter Cartridge 8 | P61210
19 Seal Ring 1 P6563
20 Pump 1 | P61208US
21 Adaptor 2 P6916
22 Hose Clamps 4 | P6124
23 Hose(®38mm) 2 | P6517
26 Adapter Nut 1 P6615
Optional Parts
12 Washer 1 | P6029
22 Hose Clamps 1 P6124
Debris Screen 2 | P6680
24 | Debris Screen 1 | P61318
25 T-Joint 1 | P61408
27 Hose ($32mm) 2 | P6019
28 O-Ring 2 P6005
29 GFCI 1 P6/83
} SPECIFICATIONS
Filter Diameter 437mm
Effective Filter Area: 1.61ft? (0.150m?)
= Max. Operating Pressure: 1.58Bar(23PSI)
= Working sand filter pressure: <0.56Mpa(8P SI)
= Max. Water Temperature: 40°C
437mm = CO Sand: Not included
(AR Sand Size: #20 silica sand,0.45-0.85mm
D Sand Capacity: Approximately 35kg
ДНО
Ÿ
, 633mm e
4
S-S-004040
[pen (458367E 2000gal EE MESA) pe
CONTROL VALVE OVERVIEW
WA RN | NG = TO prevent equipment damage and possible
injury, always switch off sand filter before changing the Control Valve
function. Changing valve positions while the pump is running can
damage the Control Valve, which may cause personal injury or property
damage.
How to Use the Control Valve:
Press down on the Control Valve handle and rotate to desired function.
CONTROL VALVE FUNCTIONS
The Control valve is used to select 6 different filter functions: Filter, Rinse, Circulate, Backwash, Closed and Drain.
Filter: This function is used to filter pool water and should be Circulate: This function circulates pool water bypassing
positioned here 99% of the time. Water is pumped through the sand filter; use this function if the filter is broken to
the sand filter, where it is cleaned and returned to the pool. collect debris in the Debris Screens.
Backwash: This function is used to clean the sand bed; Drain: This function drains water from the pool; another
water is pumped down through the Collector Hub, upwards filter bypass setting, water is pumped and deposited out
through the sand bed, and deposited out of Port D. of Port D, instead of returning it to the pool.
Rinse: This function for initial startup, cleaning, and Closed: This function stops water flowing between
sand bed leveling after Backwash; water is pumped the sand filter and the pool.
downwards through the sand bed, up through the
Collector Hub and deposited out of the valve Port D.
NOTE:
Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it
will cause flooding or damage.
* When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
» Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
- Do not set the Control Valve between two functions, or it will lead to leaking.
To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (® 3.2cm)
1. Connect the Adaptors (21) to the Hose .
2. Place the loose Hose Clamps (22) in the end of Hose unm
with Adaptor (21).
|
1.2 inch<
a EDI, ce СВИТ) , SONT —
>
A
21 >1/2in
22
3. Attach the Hoses to the corresponding letters on the pool.
4. Attach the Hoses to the sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into
position; ensure the corresponding letters on both the pool and the sand filter match (A to A, Bto B).
5. Remove the Stopper Plugs from the pool's inlet and outlet valves and insert with the Debris Screens (24).
6. With the Hoses and Debris Screens (24) in position, tighten the Hose Clamps (22).
GARDEN HOSE ADAPTOR FUNCTIONS
S-S-004040
[pen (#58367E 2000gal EEE А-В) pe |
1. Assemble the garden hose adaptor.
2. Screw the garden hose adaptor onto port D of the sand filter.
3. Attach garden hose to the garden hose adaptor.
NOTE:
1. Garden hose adaptor can be used for draining your pool and can only be assembled to port D of the sand filter.
2. Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3. Ensure the washer is in position before assembling the garden hose adaptor.
GFCI Test
A. To test the GFCI plug, insert it into a grounding type A
receptacle.
B. Press the RESET” button; the indicator turns red.
NOTE: If the indicator light is not on, the test has failed.
C. Press the TEST" button. The indicator turns off.
NOTE: If the indicator light is not off, the test has failed.
D. Press the "RESET" button, the indicator light turns red, and the sand filter is ready for use.
WARNING: RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE EACH USE.
WARN N G: DO NOT USE THE PUMP IF THE ABOVE TEST FAILS. Please contact your local Bestway Aftersales
Service.
Section |: Assembly (You will need a Phillips screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is
damaged. If equipment is damaged, immediately notify the retailer from where the
equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab.
Position the sand filter so the Ports and Control Valve are accessible for operation,
servicing and winterizing.
3. EN60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground dam
or a certain pedestal made of wood or concrete before use to prevent the sand filter
from accidentally falling. Fully assembled sand filter will exceed 35kg. The mounting holes should be 8mm in diameter and
spaced 86mm apart. Use two bolts and nuts with a maximum of 8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE: Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately
one 35kg bag should suffic If you do not use the recommended size of filter sand, filtering performance will be reduced and the
sand filter may damaged, there by voiding the warranty.
NOTE: To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the
Skimmer on the Hub.
NOTE: SAND NOT INCLUDED.
1. Place the tank base in the right place, aligning the position hole.
2. Place the tank onto the right place of tank base.
3 .Place the filter cover(4).
4. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the
marked "MAX" and “MIN". #20 Silica sand 0.45-0.85mm, approximately 35 kg.
el
Fy
S-S-004040
[pen (#58367E 2000gal EEE А-В) pe
5. Pull out the filter cover (4).
6. Lower the control valve over the tank slowly,and ensure the bypass pipe protruding underneath the control valve fits securely
into the hub (6).
7. Make sure Port C on the Control Valve is align Port C on the Pump. Attach the Top Flange Clamp (3) and screw into position.
8. Attach the Piping (14) to Pump Port C and to Control Valve Port C, screw the threaded locking rings into position. Make sure
the Washer is properly positioned on both ends of the Piping (14).
Section Il: Hose Configuration for Backwashing and Rinsing
NOTE: Ensure the Control Valve is set to the Closed function.
Your pool should be filled with water, make certain all of the pool's Debris Screens (24) are fully submerged in water.
Please check if your product includes a T-Joint (25) (see Fig. E).
If yes, assemble your sand filter referring to method A;
if no, assemble your sand filter referring to method B.
Method A (see Fig.A-1)
1. Attach one end of the hose (23) to the sand filter's Port B; screw the threaded locking ring into position.
2. Connect both ends of hoses (P32mm) to the pool valves marked “B”, place the loose Hose Clamps (P6124) on the end of
Hoses. Connect both free ends of hoses ($32mm) to the T-joint (P61408) by tightening the Hose Clamps.
3. Screw the other end of the hose (23) to the T-joint (25), screw the threaded locking ring into position.
4. Remove the Stopper Plugs from the pool’ s outlet valves (marked “B") and insert with the Debris Screens. With the Hoses
and Debris Screens in position, tighten the Hose Clamps.
Method B (see Fig.B-1)
1. Attach one Hose (23) to the sand filter's Port B; screw the threaded locking ring into position.
2. Screw the other end of the Hose (23) to Port B connection valve; screw the threaded locking ring into position.
3. Open the connection valve.
3 . Li
e 2 Poros a e |
и P6680"
Fig.A-1
23 (1m)
Fig.E
NOTE: You can refer to pool manual for connection valve's installation instructions.
Screw the other Hose (23) to Port D and place the opposite end in drain area.
Section Ш: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device, and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Switch off the sand filter and set the Control Valve to the Rinse function.
4. Switch on the sand filter and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains
water out Port D.
5. Switch off the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
S-S-004040
[pen (#58367E 2000gal EEE А-В) pe
| M PO RTANT: This procedure removes water from the pool, which you'll need to replace. Switch off
the sand filter immediately if water levels near the pool's Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
Connect the Second Hose
N OTE = ltis imperative to check that the hydraulic connectors are not obturated.
NOTE: Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig. E), and referring to B-2 if not. The assembly methods are
the same.
1.Detach the Hose (23) from Port D.
2. Attach the Hose (23 )to the Control Valve's Port A; screw the threaded locking ring into position.
3.Connect the other end of Hose (23) to the pool's Inlet A.
4.Open the connection valve.
a " 1 . = = =
NOTE = You can refer to pool manual for connection valve's installation instructions.
Water level
23 (1m)
Fig.A-2
Section V: Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE: To prevent the risk of electrical shock dry any excess water from yourself and the
sand filter.
2. Switch on the sand filter to run it.
NOTE: The sand filter has now started its filtering cycle. Check that water is returning to
the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended
sand filter pressure is less than 0.56Bar (8.0PSI) when it is running.
Sand Filter Maintenance
CAUTION = You must ensure the sand filter is switched off and unplugged before any
maintenance begins or severe risk of injury or death exists.
As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When
the Pressure Gauge is 0.56Bar (8.0PSI) or higher, or water flow to the pool is too low, it is time to
clean the sand.
To clean the sand bed, follow all instructions outlined previously in Section Il and Section Ill:
Backwash and Rinsing.
NOTE:
1. The Pressure Gauge is just used for measuring the water pressure, not used for precision
measurement.
2. We recommend you clean the sand bed once a month or less regularly depending on how
often the pool is used.
Do not clean the sand too frequently.
S-S-004040
[pen (#58367E 2000gal EEE in RA) pe
Cleaning the Strainer
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Close the connection valves.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Open the connection valves.
NOTE = The Strainer must be emptied and cleaned periodically.
A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve's Port A and sand filter Port A and attach to Port D.
3. Switch on the sand filter to remove pool water.
WARN | NG = DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage. Allowing water
to freeze will damage the sand filter and void warranty.
1. Backwash the sand filter as previously outlined in Section Il and Section Ill.
2. Drain the pool according to the pool owner's manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child's reach.
TROUBLESHOOTING
Problems Probable Causes Solutions
Sand Filter does not operate | - GFCI broken - Contact your local Bestway Aftersales Service point to get instructions
- Sand is too small - Recommend 0.45mm to 0.85mm #20 silica sand
- Move the control valve from the backwash to the - Stop the sand filter every time set the control valve ; ‚
Sand is flowing to the pool | filter function without stopping the sand filter - Check if the level of the sand is between the marked “MAX” and “ MIN” on the
- The level of the sand is too high collector hub
- The skimmer is broken - Replace the skimmer
- Stopper plugs are not removed - Remove the stopper plugs and insert the debris screens
- Air was not released - Release the air
No water flow - The control valve is set to Closed - Set to filter function
- The strainer is blocked - Clean the strainer
- Sand filter broken - Call for service
- Dirty filter - Backwash
Excessive filter pressure - Calcified sand bed - Inspect sand and change if necessary
Р - Insufficient backwashing - Backwash until water runs clear
- The pressure gauge is broken - Replace the pressure gauge
Control Valve leaks - Control Valve is set between two functions - Set to one function
from the port D - The gasket is broken - Replace the gasket
- Washer of the connectors not in place - Reposition the washer
к - Washer of the connectors broken - Replace the washer
Connectors lea - O-ring on the hose connection is broken - Replace the o-ring
- Loose Hoses - Tighten them
9
S-S-004040
-S-004040/21.0x28.5cm (458367E 2000gal EEES) pe
Limited BESTWAY® Manufacturer’s Warranty
The product you have purchased comes with a limited warranty. Bestway® stands behind our quality guarantee and assures, through a replacement
warranty, your product will be free from manufacturer's defects that result in leaks. If a Manufacturer defect is found within: 360 days for the motor
pumps from the original date of purchase for 30 days for hoses, fitting and accessories included in the package from the original data of purchase.
To enact a warranty claim, this form must be completed and supplied with a copy of your purchase receipt to your local Bestway After Sales Center.
Please contact your local Bestway After Sales Center before sending any documents, they will provide full instructions of what is needed for your claim.
Bestway® is not responsible for economic loss due to water or chemical costs and Bestway® will not replace any products deemed to have been
damaged due to negligence or having been used outside of the owner's manual guidelines.
Bestway's warranty covers manufacturing defects discovered while unpacking the product or during use as recommended within the user manual, this
warranty applies only to products which have not been modified by any 3" parties. The product must be stored and handled in accordance with the
technical recommendations.
The warranty does not cover damages caused by misuse, abuse, neglect, including, but not limited to collision, fire, use of incorrect voltage, excessive
heat exposure, improper installation, improper wiring or testing, or improper storage.
Replacements and repairs don't extend the duration of the warranty. The date to be considered as the start of the warranty is only the one shown in the
original receipt/purchase invoice.
Please copy the Batch Number located on the body of the sand filter.
Batch
#5 Number “A FE = я
7 Batch ==" Batch * Batch
4 Number Number = Number
Batch Number: Date of purchase receipt:
TO: BESTWAY® SERVICE DEPARTMENT DATE: Customer Code Number:
FAX/E-MAIL/TEL: Please refer to your country according to the information you find on the back cover or on our website: www.bestway-service.com
Please provide your address details in full. Note: Incomplete address details will result in delayed shipments.
Bestway reserves the right to charge for redelivery of undelivered packages where the recipient is at fault.
REQUIRED INFORMATION -- PLEASE WRITE THE DELIVERY ADDRESS
Name: Address: Zip code:
Country: City: Mobile:
Telephone: Fax: E-mail:
Retailer: Please Clearly Write Your Item Code:
Item Code
A
FROUCUAR”
SAND FILTER MODEL #HXAXXXKX
Y
All drawings for illustration purpose only. Not to scale.
Description of problem
© Water leaking
O stopped working
O Item is incomplete, Which part is missing — Please put the code you find on the instruction manual
O Others, please describe
IMPORTANT: ONLY THE DAMAGED PART WILL BE REPLACED, NOT THE COMPLETE SET.
Bestway reserves the right to request photographic evidence of defective parts, or to require the sending of the item for additional testing.
In order to best assist you, we request all information you provide is complete.
FOR FAQ, MANUALS, VIDEOS OR SPARE PARTS, PLEASE VISIT OUR WEBSITE WWW.BESTWAY-SERVICE.COM. =
VIDEOS ARE ALSO AVAILABLE ON OUR BESTWAY CHANNEL ON YOU TUBE: http://youtube.com/user/BestwayService. es Way
BP
10
S-S-004040
[pen (#58367E 2000gal EEE А-В) pe
estwa
11
S-S-004040
[pen (458367E 2000gal EE MESA) pe
Albania
Phone: (+355) 682003429
Fax: (+386) 056621203
E-mail: servis @ bestway si
Argentina
Phone: (+54) 1159843871
E-mail:
argentina @ bestway-southamerica.com
Australia
Phone: (+61) 290371388
Fax: (+61) 297379423
E-mail:
aftersales @ bestway-australia.com
Austria
Phone: (+43) 720882434
Fax: (+43) 720882435
E-mail: austria@ bestway-service.com
Belgium
Phone: 0 800 20 132
Fax: (+32) 026104411
E-mail:
belgiumservice @ bestway-europe.com
Bosnia
Phone: (+387) 039670935
Fax: (+386) 056621203
E-mail: servis @ bestway.si
Brasil
Phone: 0800 001 8400
E-mail: sac @ bestway-brazil.com
Bulgaria
Phone: (+359) 879012892
Fax: (+359) 29250232
E-mail: bulgaria @ bestway-service.com
Canada
Phone: 1 855 838 3888
Fax: 1 480 838 1888
E-mail:
info l bestway-northamerica.com
Chile
Phone: (+56) 2232036438
E-mail:
postventa @ bestway-so uthamerica.com
Colombia
Phone: (+57) 13441717
E-mail:
colombia e bestway-southamerica.com
Croatia
Phone: (+385) 0997930168
Fax: (+386) 056621203
E-mail: servis @ bestway si
Cyprus
Phone: (+357) 22 426803
(+357) 22 423824
Fax: (+357) 22 495137
E-mail: cyprus @bestway-service.com
Czech Republic
Phone: (+420) 0387020573
E-mail:
pomocservis E bestway-service.com
Denmark
Phone: (+45) 33321019
Fax: (+45) 33321036
E-mail: denmark @ bestway-service.com
Finland
Phone: (+358) 5041044083
E-mail: finland @ bestway-service.com
France
Phone: 0892707709 (0,34 TTC/MINUTE)
Fax: (+33) 0489069991
E-mail: sav@ bestway-france.com
Germany
Phone: (+49) 6946001281
Fax: (+49) 6946001282
E-mail:
kundendienst @bestway-europe.com
Greece
Phone: 00.800.391.275.300
Fax: (+39) 0291390361
E-mail: ipostirixis @ bestway-service.com
Hungary
Phone: (+36) 0640204624
E-mail: hungary @ bestway-service.com
Iceland
Phone: (+46) 8 506 691 90
Fax: (+46) 506 690 99
E-mail: sweden @ bestway-service.com
Ireland
Phone: 8006120457
Fax: (+44) 01626835736
E-mail: aftersales @ bestway-uk.com
Italy
Phone: (+39) 0236265839
Fax: (+39) 0291390361
E-mai:
assistenza € bestway-europe.com
Macedonia
Phone: (+389) 032386235
Fax: (+386) 056621203
E-mail: servis @bestway.si
Malta
Phone: (+356) 27438201/21499101
Fax: (+356) 21496206
E-mail: info @ model-toys.com
Mexico
Phone: (+52) 5541693920
Fax: (+52) 8183463416
E-mail: info @ bestway-mexico.mx
Moldova
Phone: (+373) 68535552
E-mail: Moldova @ bestway-service.com
Netherlands
Phone: 8002378929
Fax: (+31) 887878969
E-mail:
dutchservice € bestway-europe.com
New Zealand
Phone: 0800 142 101
E-mail:
aftersales @bestway-australia.com
Norway
Phone: (+47) 22650122
Fax: (+47) 22721127
E-mail: norway @ bestway-service.com
Peru
Phone: (+51) 17089795
E-mail:
peru@ bestway-southamerica.com
Poland
Phone: (+48) 327505320 / 322326040
Fax: (+48) 327505330
E-mail: serwis@ bestway-service.com
Portugal
Phone: (+351) 707506692
Fax: (+34) 902602705
E-mail: sace bestwayiberica.com
Romania
Phone: (+40) 212525354 / 213362858
Fax: (+40) 212525353 / 213362854
E-mail:
suportclienti e bestway-service.com
Russia (Poccun)
Phone: +7 (495) 9778-90-88
E-mail: info @ bestway-service.ru
-S-004040/21.0x28.5cm (#58367E 2000gal EEA ERiIZAAH) pee
Authorized Service Centers
Serbia and Montenegro
Phone: (+381) 0656644962
(+386) 056621206
Fax: (+386) 056621203
E-mail: servis @bestway si
Slovak Republic
Phone: (+421) 0415078833
Fax: (+421) 0415078808
E-mail:
pomocservis € bestway-service.com
Slovenia
Phone: (+386) 056621206
Fax: (+386) 056621203
E-mail: servis @bestway.si
South Africa
Phone: (+27)-21-5771401
Toll-Free: 0800 224 881
Fax: (+27)-21-5774400
E-mail: sales @seagullindustries.co.za
Spain
Phone: (+34) 902351045
Fax: (+34) 902602705
E-mail: sac @bestwayiberica.com
Sweden
Phone: (+46) 8 506 691 90
Fax: (+46) 506 690 99
E-mail: sweden @bestway-service.com
Switzerland
Phone: (+41)(0)719290000
Fax: (+41)(0)719290090
E-mail:
switzerland @ bestway-service.com
Turkey
Phone: (+90) 02126444600
Fax: (+90) 02125550224
E-mail:
teknikservis @bestway-service.com
bestway @ feyzaticaret.com
Ukraine
Phone: (+38) 0577597227
(+38) 0677033206
E-mail:
service @bestway-ukraine.com.ua
United Kingdom
Phone: 08455760116
Fax: (+44) 01626835736
E-mail: aftersales @bestway-uk.com
USA
Phone: 1 855 838 3888
Fax: 1 480 838 1888
E-mail:
info E bestway-northamerica.com
S-S-004040