instruction manual
ENGLISH
C61195
C61198
www.claypaky.it
INSTRUCTION MANUAL
Congratulations on choosing a Clay Paky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Clay Paky range, has been designed and made with total quality to ensure
excellent performance and best meet your expectations and requirements.
Carefully read this instruction manual in its entirety and keep it safe for future reference. It is essential to know the information and
comply with the instructions given in this manual to ensure the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the characteristics stated in this instruction manual at any time and without prior notice.
|Р54
te 90°C
CE
161.00
SAFETY INFORMATION
* Installation
Make sure all parts for fixing the equipment are in a good state of repair.
Make sure the point of anchorage is stable before positioning the equipment.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if
the primary support system fails, the fitting falls as little as possible.
If the safety chain gets used, it needs to be replaced with a genuine spare.
* Minimum distance of illuminated objects
Carefully read this instruction manual dedicated to the projector inside the IGLOO.
* Minimum distance from flammable materials
Carefully read this instruction manual dedicated to the projector inside the IGLOO.
* Mounting surfaces
It is permissible to mount the fitting on normally flammable surfaces.
* Maximun / Minimum environment temperature
Do not use the device if ambient temperature (Ta) exceeds: see details on page 3.
The minimum permissible ambient temperature of use is -20 ° C.
When the environment temperature falls below 0 ° C, it is necessary to switch-on projector and
lamp located inside the Igloo, at least 30 minutes before use, so as to lead to thermal regime the
fixture effects.
* [P54 protection rating
Igloo is protected against dust (first digit 5) and splash (second digit 4).
* Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class | appliance
according to standard EN 60598-1).
It is, moreover, recommended to protect the supply lines of the equipment from indirect contact
and/or shorting to earth by using appropriately sized residual current devices.
e Connection to mains supply
Connection to the electricity mains must be carried out by a qualified electrical installer.
Check that the mains frequency and voltage correspond to those for which the equipment is
designed as given on the electrical data label.
This label also gives the input power to which you need to refer to evaluate the maximum number
of fittings to connect to the electricity line, in order to avoid overloading.
* Temperature of the external surface
The maximum temperature that can be reached on the external surface of the Igloo, in a thermally
steady state, is 90°C (194°F).
* Maintenance
Before starting any maintenance work or cleaning the device, cut off power from the mains supply.
Carefully read the projector's instruction manual for maintenance of the projector inside the igloo.
Replace any damaged part with original ones.
NOT FOR RESIDENTIAL USE
The products to which this manual refers comply with the European Directives pursuant to:
° 2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)
* 2004/108/EC - Electromagnetic Compatibility (EMC)
° 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)
WARNING:
For dimensional, thermal or operating problems, IGLOO use in CLAY PAKY projectors other than those listed or other brand projectors is
NOT permitted.
PROJECTOR MINIMUM MAXIMUM
ambient temperature ambient temperature
* Albha Spot 300
* Albha Spot HPE 300
* Albha Wash 300
* Albha Beam 300
* Albha Spot HPE 700
* Albha Beam 700
* Alpha Profile 700
* Alpha Profile 700 ST
* Albha Wash 700
* Sharpy
* Sharpy Wash 330
* A.leda Wash K5 - 20 °C + 40 °C
* A.leda Wash K10
* Aleda Wash K20 -4°F + 104 °F
* A.leda Wash K10 CC
* A.leda Wash K10 TW
* A.leda Wash K10 W
* A.leda Wash K20 CC
* A.leda Wash K20 TW
* A.leda Wash K20 W
* A.leda B-Eye K10
* A.leda B-Eye K10 Easy
* A.leda B-Eye K10 CC
* A.leda B-Eye K20
* A.leda B-Eye K20 CC
« SUPERSHARPY - 20°C + 25 °C
* MYTHOS - 4 °F +77 °F
UNPACKING AND PREPARATION
[ST008/001
161.00 3
INSTALLATION AND START-UP
WARNING:
to avoid damaging the projector,
use the screws supplied with the
bracket unit and not the ones
previously removed.
Mounting brackets for projector placement - Fig. 1
The dedicated brackets replacing the side handles should be mounted before inserting the projector in the IGLOO:
C61192 - fast fit bracket for ALPHA 300/700
C61191 - fast fit bracket for SHARPY and SHARPY WASH 330
C61183 - fast fit bracket for A.leda K10 line
C61184 - fast fit bracket for A.leda K20 line.
C61194 -quick fastening rod and connection extension for Mythos and Supersharpy
161.00 4
Projector placement - Fig. 2
Once placed in the igloo the projector is fixed to the base by tightening the screws using 1/4 turns secured to the brackets.
161.00 5
Connecting to the control signal line Igloo Easy (DMX) - Fig. 4
Use a cable conforming to specifications EIA RS-485; 2-pole twisted, shielded, 1200hm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female
connectors. A terminating plug must be inserted into the last fixture into the Igloo with a resistance of 1200hm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be
connected to the shield braid and to pin 1 of the connectors.
161.00 6
Wireless control - Fig. 5
not EASY).
The wireless control is only available in the IGLOO version
161.00
rl re
Oh=RADIO OH
AT OFF=RADIO OFF
OO
RADIO
STATUS RUN
o,
DC ON
DIP SWITCH 1: DMX ADDRESS SETTINGS
The DMX address set on the Dip-switch 1, is the address to control the
switching-on / switching-off of the device via the control unit.
O © a
© AN “ NW ov
ON “TT © «~~ 0 © += С
uuu Em
2 3 4 5 6 7 8 9 10
Set dip-switches according to the required DMX address:
Example: DMX 11 address settings
Tum dip-switches 1, 2, 4 ON
— A со
aul Lal
2 3 4 5 6 7 8 9 10
BIT STATUS
101-255 | IGLOO SWITCHED-ON
26-100 | IGLOO SWITCHED-OFF
0-25 NO FUNCTION
161.00
DIP-SWITCH 2: RECEIVING CONTROL MODE SETTINGS
Switch 1, 2, 3 ON: Switch 1, 2, 3 OFF:
Wireless operating mode (Radio) Wired operating mode (DMX cable)
ERE [wi
2 3 4 2 3 4
LED LANGUAGE
* GREEN LED ON: DMX board power on
* RED LED
On Bootloader
Off No DMX signal
Relay OFF
Slow flashing DMX signal found
Relay OFF
Fast flashing No DMX signal
Relay ON
Mixed flashing DMX signal found
Relay ON
YELLOW LED
Off Not assigned to a transmitter
Assigned to a transmitter
and no DMX signal
On Assigned to a transmitter and
DMX signal found
link to transmitter lost or
connecting to transmitter
Mixed flashing
Fast flashing
vy
OOD
(1
Л) >
MO
ES
DMX connection cable for IGLOO (not EASY) - Fig. 7
PLEASE NOTE: If you do not intend to use the wireless option, the DMX cable must be connected as seen in fig.7 and not directly to the
projector.
Closing the device - Fig. 8
161.00 9
CAUTION:
The 2 IGLOO conveyors should always be facing
down. By gripping them with both hands it is
possible to rotate them in the desired position.
An acoustic signal will alert incorrect conveyor
positions.
Installing Igloo - Fig. 9
WARNING: with the exception of when the Igloo is positioned on the floor, the safety cable must be fitted. (Cod.
105041/003 available on request). This must be securely fixed to the support structure of the equipment and then
connected to the fixing point at the centre of the base.
If the device is fixed to a wall, horizontally, mount the kit C61193 for proper and complete installation Fig.10.
161.00 10
10] (61193 - OPTIONAL ACCESSORIES
1 x 105041/003
1 x 033205
1 x 272023/001
Mounting kit C61193 - Fig. 10
161.00
11
CAUTION:
To avoid damage to the internal parts of the fixture, installed inside the IGLOO, when the fixture is not working, is
recommended to turn the head down before turning the fixture off, so that the front lens of the fixture is invested as
little as possible from the sun.
161.00 12
Lock assembly - Fig. 12
The device latches are fitted with holes for affixing safety locks if desired.
13
161.00
MAINTENANCE
2x Fuses
6,3 x 32mm 2AT (030472)
N
Replacing fuse - Fig. 13
161.00 14
WARNING:
no alcohol
Periodical cleaning - Fig. 14
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits.
The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality
of the working environment (air humidity, presence of dust, salinity, etc.).
It is recommended that the equipment undergoes an annual service by a qualified technician for special maintenance involving at least the following
operations:
* General cleaning of internal parts.
* General visual check of the internal components, cabling, mechanical parts, etc.
* Electrical and functional checks; eventual repairs.
Cleaning igloo cover
Clean the cover using only water and mild soap, using a sponge or soft and smooth cloth.
Do not use alkaline or abrasive detergents or halogenated or aromatic solvents such as toluene, benzene, petrol, acetone or carbon tetrachloride.
Do not clear in direct sunlight since it could stain.
161.00 15
TECHNICAL INFORMATION
Power supplies available
* 100-120V 50/60Hz
* 200-240V 50/60Hz
Input power:
* 250VA a 230V 50Hz (Igloo, Igloo Easy)
* Max 1450VA a 230V 50Hz (Projector)
Input
DMX 512 / wireless
IP54 protection rating
* Protected against dust
* Protected against splashing
CE Marking
Complies with the following European Directives
- 2006/95/EC (LVD)
- 2004/108/EC (EMC)
- 2011/65/EU (RoHS).
Safety Devices
* Two 2AT fuses.
* The projector placed in the igloo is also equipped with safety devices (see dedicated manual)
Cooling
Forced ventilation with fans.
Anti-condensation system
Pair of RTDs
Body
* Stainless steel structure with plastic pressure casting covers.
* Four side handles for transportation.
Working position
Functioning in any position.
Weights:
about 32 Kg.
Note:
Carefully read the instruction manual, dedicated to the projector inside the Igloo, for additional technical
details.
CLAY PAKY s.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035 -654311 - Fax +39-035-301876 - www.claypaky.it
gfistudio
IST008/001 — EN - Rev.B 09/14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising