WarmTouch - Domoteck

WarmTouch - Domoteck
WarmTouch Mats & Cables
.
WarmTouch
for STANDARD
and LARGE AREAS
USA 2014
All graphics & pictures are for illustration only
WarmTouch Mats & Cables
Copyright 2006-2014 © All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
WarmTouch Mats & Cables
Resistance Wires
(twin)
FEP
Coating
Reinforced
insulation
Polyamide
Jacketing
Shielded
Grownding
Super strong
aramid
WarmTouch Classic Mats
VOLT
WIDTH
)FT(
LENGTH
)FT(
SQFT
120v
1
6-50
6-50
120V
1.5
10-50
15-55
120V
3
2-20
6-60
042V
1
02-02
02-02
042V
1.0
12-02
10-50
042V
0
12-02
02-102
Exact measurements: Width ,length and output
to be found in DomoTeck SLP ( Suggested List Price).
Tested in accordance with UL and CSA.
to be installed in accordance to NEC.
All graphics & pictures are for illustration only
Technical Data
Mat Output 120v
15Wsqft
240v
12Wsqft
Mat Output
Cable Output
3W/Linear Ft
Voltage
120V AC / 240V/60HZ
Cable Outer jacketing
PA Jacketing
Wire Thickness
1/8”
Protection Means
GFCI In accordance to NEC
Supply Lead Connection
One side connection
(Twin Conductor)
Base Material
White textile mesh
Cable Color
Green
Wire Spacing
2 1/4”
Cold Lead Length
13ft
WarmTouch Mats & Cables
Copyright 2006-2014 © All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
2
Installation
1
2
WET INSTALLATION
Attach one of Domoteck ‘s
testing instrument
Plan the layout
4
3
Thermostat to regulate floor temperature
Place insulation boards and coat the
surface with a primer
Two adjacent conduits
1. Protecting Tube ( non heating leads)
2. Sensor pipe
Junction Box
Tiles or other stone
covering
Spread first layer of thin set morter
6
5
Thin set mortar or self leveling
mortar
Warming
element
Sub-Floor
Spread second layer of tile glue
Using a roller press down the mat
Insulation
7
Building structure
OR
8
Pour self-leveling morter
Using various fixing means
fix the mat to the insulation
boards
9
Place floor covering e.g. tiles
All graphics & pictures are for illustration only
10
Set the thermostat
WarmTouch Mats & Cables
Copyright 2006-2014© All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
3
WarmTouch Mats & Cables
Resistance Wires
(twin)
FEP
Coating
Super strong
aramid
Reinforced
insulation
Polyamide
Jacketing
Shielded
Grownding
SEE ACCESSORIES
11, 13, 15 watt sqft
Warm Touch Classic Cables

WarmTouch Classic Cables are perfectly suited for new construction and remodeling
projects. The warming element can be integrated into almost any floor cross-section
with a minimal change in floor elevation.

WarmTouch Classic Cables are perfectly suited for wet installation under tile, stone
and marble.

WarmTouch Classic Cable is a twin– conductor cable and has a single connection
point that simplifies the installation process.

WarmTouch Classic Cable gives the homeowner the flexibility to decide the W/sqft
and allows him to reach places which cannot easily be reached by a mat.
VOLT
Cable Length
Output ( 2.75W/
linear Ft)
Technical Data
Mat Output
2.75W/Linear Ft
Voltage
120V AC / 60HZ 240V
AC /60HZ
Cable Outer Insulation
PA Jacketing
Exact measurements: Width ,length and output
to be found in DomoTeck SLP ( Suggested List Price).
Wire Thickness
1/8”
Protection Means
GFCI In accordance to NEC
Tested in accordance with UL and CSA.
to be installed in accordance to NEC.
Supply Lead Connection
One side connection
(Twin Conductor)
Cable Color
Green
Supply Lead Length
13Ft
120V
48-516
100-1411
042v
44-606
100-1541
All graphics & pictures are for illustration only
WarmTouch Mats & Cables
Copyright 2006-2014 © All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
4
Installation
1
2
WET INSTALLATION
Attach one of Domoteck’s testing
instruments
Plan the layout
3
4
Thermostat to regulate floor temperature
Two adjacent conduits
1. Protecting Tube ( non heating leads)
2. Sensor pipe
Place insulation boards and coat the
surface with a primer
Junction Box
Tiles or other stone
covering
Thin set mortar or self leveling
mortar
5
If using the insulation, fix the anchoring
means down onto the boards
If not, fix the anchoring means to the
sub floor
Warming
element
Sub-Floor
Sensor
Insulation
Building structure
Fix the cable into the anchoring
means
6
domoteck’s warranty policy
Domoteck’s products are guaranteed
by a 10-year Limited Product Warranty,
and are designed to safely operate according to the life-span
of the application in which they are installed.
Spread a layer of thin set mortar
8
7
Pour self-leveling mortar
9
Place floor covering e.g. tiles
All graphics & pictures are for illustration only
OR
Set the thermostat
WarmTouch Mats & Cables
Copyright 2006-2014© All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
5
WarmTouch Mats & Cables
Reinforced
insulation
Braided grounding
(to activate GFCI)
Polyamide
Jacketing
Resistance Wires
Super strong
aramid
WarmTouch Basic Mats




WarmTouch Basic Mats are ideal for installation under tile, stone and marble especially
in large areas. They are also versatile to warm other approved floor coverings such as
floating , laminates, linoleum and wall-to-wall carpeting.
WarmTouch Basic Mats are simple to install ( Are delivered as semi fixed size just lay
the mat and fix it to subfloor, see illustration), ultra safe and economically affordable.
They are perfectly suited for installation in new construction and remodeling projects.
WarmTouch Basic Mats feature an absorbent textile mesh that simplifies the mat installation and perfectly integrating into the floor cross-section.
WarmTouch Basic Mats should be embedded in latex-modified thin-set mortar for tile
and stone warming applications.
VOLT
WIDTH
(FT)
LENGTH
(FT)
SQFT
W/UNIT
Technical Data
Mat Output
12Wsqft
240V
4
5-22.5
20-100
240-1200
Cable Output
3 W/ft
240V
6
5-22.5
30-135
360-1620
Voltage
240V AC / 60HZ
Exact measurements: Width ,length and output
to be found in DomoTeck SLP ( Suggested List Price).
Cable jacketing
PA 12
Wire Thickness
1/9”
Tested in accordance with UL and CSA.
to be installed in accordance to NEC.
Protection Means
GFCI In accordance to NEC
Supply Lead Connection
Two sided connection
Base Material
White Textile
Cable Color
Orange
Wire Spacing
3”
Supply Lead Length
2x10ft each side
For further details refer to product installation manual
All graphics & pictures are for illustration only
WarmTouch Mats & Cables
Copyright 2006-2014 © All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
6
Mat Flexibility
WarmTouch Basic Mats come factory prepared as a “ Fixed
Size” to warm basic rectangular shaped areas.
Just unroll the mat, open it and adhere it to the sub- floor
OR
The mat can be easily re-shaped by cutting the mesh ( DO
NOT CUT THE WIRE) and adjust it to cover the required floor
space.
Follow the simple illustrations outlined in the product installation
guide to learn more about how to achieve the custom coverage
you need.
All graphics & pictures are for illustration only
WarmTouch Mats & Cables
Copyright 2006-2014© All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
7
WarmTouch Mats & Cables
Super strong
aramid
Resistance Wires
Reinforced
insulation
Braided grounding
(to activate GFCI)
Polyamide
Jacketing
SEE ACCESSORIES
11 , 13 , 15 watt sqft
Warm Touch Basic Cable

WarmTouch Basic Cables offer the best solution in installation flexibility; installers can
modify the space between the wires according to the required heat load.

WarmTouch Basic Cables are ideal for installation under tile, stone, and marble, especially in large areas. They are also versatile enough to warm other approved floor coverings such as floating wood, laminates, linoleum and wall-to-wall carpeting.

WarmTouch Basic Cables should be fixed to the subfloor with Domoteck’s custom distance Keepers or with adhesive tape.
* Contact Domoteck customer service for more information about the distance keepers
WarmTouch Classic Cable gives the homeowner the flexibility to decide the
W/sqft and allows him to reach places which cannot easily be reached by a mat.
VOLTS
CABLE
LENGTH
SQFT
COVERED
15W/Sqft
SQFT
COVERED
13W/Sqft
SQFT
COVERED
11W/Sqft
042V
44-606
1-115
12-100
10-101
102V
44-016
1-10
12-125
10-101
Exact measurements: Width ,length and output
to be found in DomoTeck SLP ( Suggested List Price).
Tested in accordance with UL and CSA.
to be installed in accordance to NEC.
All graphics & pictures are for illustration only
Technical Data
Cable Output
2.75 W/ft
Voltage
120V AC/ 60HZ
240V AC / 60HZ
Cable jacketing
PA 12
Wire Thickness
3/32”
Protection Means
GFCI In accordance to NEC
Supply Lead Connection
Two sided connection IVC
Cable Color
Orange
Supply Lead Length
2x10ft
WarmTouch Mats & Cables
Copyright 2006-2014 © All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
8
WET INSTALLATION
2
1
Attach one of Domoteck’s testing
instruments
Plan the layout
4
3
Thermostat to regulate floor temperature
Two adjacent conduits
1. Protecting Tube ( non heating leads)
2. Sensor pipe
If using the insulation, fix the
anchoring means down onto
the boards
If not, fix the anchoring means to
the sub floor.
Place insulation boards and coat the
surface with a primer
5
Junction Box
Tiles or other stone
covering
Thin set mortar or self leveling
mortar
Warming
element
Sub-Floor
Insulation
Building structure
Fix the cable into the anchoring
means
OR
7
Spread a layer of 1/2” thin set mortar
8
Place floor covering e.g. tiles
All graphics & pictures are for illustration only
Pour self-leveling concrete
9
Set the thermostat
WarmTouch Mats & Cables
Copyright 2006-2014© All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
9
WarmTouch Mats & Cables
Wood Warming Mats
VOLTS
LENGTH
(Ft)
WIDTH (Ft)
SQFT
W/unit
120 V
10-50
1.5
15-55
150-550
Technical Data
Mat Output
10W/Sqft
Cable Output
1.7W/Linear Ft
Exact measurements: Width ,length and output
to be found in DomoTeck SLP ( Suggested List Price).
Voltage
120V AC / 60HZ
Cable jacketing
PA 12
Tested in accordance with UL and CSA.
to be installed in accordance to NEC.
Wire Thickness
5/64”
Protection Means
GFCI In accordance to NEC
Supply Lead Connection
Two side connection
Base Material
White Textile + Aluminum foil
Cable Color
Silver
Wire Spacing
2”
Supply Lead Length
2x13ft each side
All graphics & pictures are for illustration only
WarmTouch Mats & Cables
Copyright 2006-2014 © All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
11
1
2
DRY INSTALLATION
Plan the layout
3
1
2
1 = Thermostat
2 = Tube for Floor Sensor
3 = Junction Box
4 = Sensor
5 = Wooden Floor/Parquet
6 = Warming Element
7 = CCPE (closed cell polyethylene)
8 = Sub floor
9 = Insulation
10 = Construction
Attach one of Domoteck’s testing
instruments
4
Roll out the CCPE
5
Roll the AL-mat over the CCPE
6
3
4
5
6
7
8
9
10
Frame the Al-mat with
a blind net
Place floor covering
e.g. parquet
7
For full installation details please refer
to product installation manual
Set the thermostat
All graphics & pictures are for illustration only
WarmTouch Mats & Cables
Copyright 2006-2014© All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
11
WarmTouch Mats & Cables
Reinforced insulation
Resistance wire
Adhesive tape
Heat
distribution strip
Super strong
aramid
Shielded Braiding
FEP Coating
DOMOTHERM CLASSIC MAT TWIN
Domotherm Mats can be installed under:
· Tiles, marble flooring (wet installation)
· Laminated wooden floors (dry installation)
Other flooring materials that are applicable for floor heating or warming. As "wet installation" or "dry installation".
The Domotherm mat is manufactured with a screened heating element which is integrated within a wide
thin heating distribution strip. This construction of the heating element offers great advantages compared
to thin sheet flexible heating elements with integrated cable and these are:
•Short heat up time
•Temperatures can be easily regulated
•Domotherm is environmentally friendly, high-comfort and safe.
•Its flat structure (0.04”) minimizes floor elevation and can be easily applied to existing floors-ideal for renovation.
•The Domotherm mat is designed and manufactured in accordance with the highest safety standards.
Technical Data
Exact measurements: Width ,length and output
to be found in DomoTeck SLP ( Suggested List Price).
All graphics & pictures are for illustration only
Mat Output
12W/Sqft
15W/Sqft
Cable Output
3W/Linear Ft -3.75W/Linear Ft
Voltage
240 V/ 60HZ
Ribbon width
1”
Wire Thickness
1/13”
Protection Means
GFCI In accordance with
NEC
Supply Lead Connection
One side– twin conductor
Base Material
Red Fiberglass + Al
Wire Spacing
3” 1/7
Supply Lead Length
2x 10Ft
WarmTouch Mats & Cables
Copyright 2006-2014 © All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
12
WET Installation
1
2
WET INSTALLATION
Attach one of Domoteck’s testing
instruments
Plan the layout
3
4
Thermostat
Conduit
Junction box
Place insulation boards and coat the
surface with a primer
Flooring
Tiles or Natural Stone
FWM embedded
In thin set morter
Sensor
Spread first layer of
thin set morter
6
5
Construction
Insulation of the
building
Sub-floor
Press down the mat
Spread second layer of
thin set morter
OR
OPTIONAL
To improve efficiency DOMOTECK recommends using insulation
boards in your installation
7
8
Fix the mat with various
fixing means
Pour self-leveling morter
Thermostat
Conduit
Junction box
9
Flooring
Tiles or Natural Stone
Sensor
10
FWM installed on insulation
boards
Construction
Insulation of the
building
Sub-floor
Place floor covering e.g. tiles
Set the thermostat
For full installation details please refer to product
installation manual
All graphics & pictures are for illustration only
WarmTouch Mats & Cables
Copyright 2006-2014© All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
13
DRY Installation
1
2
DRY INSTALLATION
Plan the layout
Thermostat
3
Attach one of Domoteck’s testing
instruments
4
Conduit
Junction box
Flooring
Sensor
FWM Installed on
CCPE 4mm
Construction
Insulation of the building
Roll out the CCPE
Roll the mat over the CCPE
6
5
Sub-floor
Frame the mat with a blind
net
Place floor covering
e.g. parquet
8
7
E.g. carpet
Set the thermostat
For full installation details please refer to product
installation manual
All graphics & pictures are for illustration only
WarmTouch Mats & Cables
Copyright 2006-2014© All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
14
WarmTouch Mats & Cables
Living Heat Under floor mat
The Living Heat –unlike any other- is an ultra thin heating mat (25 micron ribbon total height with
mat :2.5mm)
based on the unique and patented Amorphous Metal Ribbon heating technology.

Specially designed to be a total project solution down to the smallest room or conservatory, its ultra
thin
structure and low surface temperature provides you with an easy to install product, Suitable for new
constructions as well as renovations.

An energy efficient heating system.

The Living Heat is available in fixed or semi-flexible sizes, allowing you to obtain the best coverage.

The Living Heat must be connected to the main electric box through an GFCI (30mAMps) that not
only protects the heating element but also increases personal safety.

Perfect heat distribution due to its flat structure and good surface coverage.
Living Heat mats can be installed under: Tiles and marble flooring (wet installation)
Laminated wooden floors (dry installation)
VOLT
120V
102V
WIDTH
(inch)
LENGTH
(FT)
SQFT
02”
3-18
5-30
42”
0-10
12-42
Technical Data
W/UNIT
04-044
116-444
Exact measurements: Width ,length and output
to be found in DomoTeck SLP ( Suggested List Price).
Tested in accordance with UL and CSA.
to be installed in accordance to NEC.
All graphics & pictures are for illustration only
Voltage
120V AC
Watt Sqft
12w/SQFT
Outer insulation
LLDPE
Thickness of mat/wire
0.10”
Ribbon width
0.276”-0.984”
Protection class/means
GFCI in accordance with
NEC
Connection
One side connection
Net color
Orange
Supply lead length
2x5m(16 feet)
WarmTouch Mats & Cables
Copyright 2006-2014 © All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
15
WET Installation
1
WET INSTALLATION
2
Attach one of Domoteck’s testing
instruments
Plan the layout
3
4
Thermostat
Conduit
Junction box
Place insulation boards and coat the
surface with a primer
Flooring
Tiles or Natural
FWM embedded
In thin set morter
Sensor
Spread first layer of
Thin set morter
6
5
Construction
Insulation of the
building
Sub-floor
Press down the mat
Spread second layer of
Thin set morter
OR
OPTIONAL
To improve efficiency DOMOTECK recommends using Insulation
boards in your installation
7
8
Fix the mat with various
fixing means
Pour self-leveling morter
Thermostat
Conduit
Junction box
9
Flooring
Tiles or Natural Stone
Sensor
10
FWM installed on insulation
boards
Construction
Insulation of the
building
Sub-floor
Place floor covering e.g. tiles
Set the thermostat
For full installation details please refer to product
installation manual
All graphics & pictures are for illustration only
WarmTouch Mats & Cables
Copyright 2006-2014© All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
16
DRY Installation
1
2
Plan the layout
DRY INSTALLATION
3
Attach one of Domoteck’s testing
instruments
4
Thermostat
Roll out the CCPE
6
5
Conduit
Roll the mat over the CCPE
Junction box
Flooring
Sensor
FWM Installed on
CCPE 4mm
Construction
Insulation of the
building
Frame the mat with a blind
net
Place floor covering
e.g. parquet
Sub-floor
8
7
e.g. Carpet
Set the thermostat
For full installation details please refer to product
installation manual
All graphics & pictures are for illustration only
WarmTouch Mats & Cables
Copyright 2006-2014© All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
17
Control units
CU 111-SF
DESCRIPTION
CU111-SF is a 5-day programmable thermostat
designed for floor warming. The thermostat has
an integrated Ground Fault Circuit Interrupter
(GFCI, Class B). The thermostat and the GFCI is a
dual model suitable for 120/240V 50/60Hz
supply.
TECHNICAL DATA:
CHARACTERISTICS
FLOOR MODE
41°F-104°F
Range
(05-40ºC)
32°F
Accuracy
(0.5C°)
Programmable
Yes
Remote Floor Sensor
Yes 8ft (2.5m)
Adjustable Switching Differential
Yes
Thermostat Tested
IPX 0
Manual Override
Yes
Memory Backup
Yes
Max Switching Current
16A
Supply Option
120V AC/240V AC
Energy Unit
NO
Dimensions (mm)
115x90x16
& FEATURES:
 Color - White
 Large LCD display + Display temperatures
Recalibrates.
 Built-in GFCI
 Two relays for protection against writing error
 5 day programming with 4 separate
Time & Temperature periods per day
 Permanent user setting and program setting
retention during power loss.
 Optional temperature display of Celsius or
Fahrenheit scale.
 Optional types of control for different heating
applications: room control, floor control or
room control with floor temperature limitation.
For more information
info@domoteck.us
All graphics & pictures are for illustration only
Control untis
Copyright 2006-2014 © All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
18
Control units
CU 512 S/F
TECHNICAL DATA:
CU 512-S/F
CHARACTERISTICS
FLOOR MODE
41°F-104°F
(05-40ºC)
32°F
Range
Accuracy
Programmable
Remote Floor Sensor
Adjustable Switching Differential
Thermostat Tested
Manual Override
Max Switching Current
Supply Option
Energy Unit
Dimensions (mm)
Yes
Yes 9ft (3m)
Yes
DESCRIPTION







IP 21
Yes
16A
120V AC/240V AC
Yes
86x86x16





CU 512 S/F
CU 512 S/F
Connected to
Heating Element
through
GFCI for safety
&
FEATURES:
Color: Off-White
Energy unit is connected to line voltage
Heating element is connected to energy unit
Only a shallow junction box is required
Decorative Design - Midsize Display - Backlit Display
ºC/ ºF option
Weekly Program Setting Individual 5-day Setting
0-day (weekday) + 2-day (Saturday/Sunday)
0-day (weekday) + 1-day/1-day (Saturday/Sunday)
Programmable (6 events per 24 hours)
Time & Temperature
Control Panel 5.5V SELV (higher safety
in bathrooms, children’s rooms etc.)
Connected to Domoteck Energy Unit
Control Panel and Energy Unit are separate
units
and can be installed as such
Includes instruction manual
120V Energy Unit
CU 512S/F
240V Energy Unit
Multifunction Energy Unit (120V & 240V)
02/51
AMPS 5mA
GFCI Receptable
For more information
info@domoteck.us
SENSOR
Heating Element
All graphics & pictures are for illustration only
Control untis
Copyright 2006-2014 © All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
19
Accessories for Mats & Cables
Name
Article No.
Product
units
Application
Tube for Sensor 1/2” 5ft
1001 440 219
1 unit
Installation of Thermostat Sensor
900C Angle AC 704
8-12
1001 440 218
1 unit
Fixing Sensor Tube in place
Installation Kit AC 718
Including pipe
14/2+1”+angle+corrugated 8” +
electrical box
1001 470 095
1 set
Installation of control unit
CCPE Insulation mats AC 705
0.50 x 0.50 - 6 units 1.5m2/4mm
1001 440 194
16sqft
Installation under the Aluminium
Mat
Blind Net AC 707
1.5x33
1001 440 001
54sqft
To be framed around the
aluminum mat to level off the
floor height
Aluminium adhesive tape
164ft
1001 440 199
164ft
For fixing cable to the sub floor
1001 440 298
1001 440 299
1001 440 300
20 unit x 1.5 ft
20 unit x 1.5 ft
20 unit x 1.5 ft
Spacing loops - 3”
Spacing loops - 2 1/2”
Spacing loops 2 13/64”
Ecc 3
( electrical connection chain)
1001 440 894
1 unit
ECC-connection
Ecc 5
(electrical connection chain)
1001 440 895
1 unit
ECC-connection
Fixing Strip Aluminium
Length 30Ft
NEW
Copyright 2006-2013 © All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permissi on of the copyright holder.
21
DOMOTECK Floor Warming Systems Inc. is the North American distributor and the proud subsidiary
of Domoteck Ltd.
DOMOTECK Ltd. is a world leading manufacturer of advanced radiant heating systems
based on the principle of energy-efficient, low temperature heating.
DOMOTECK also offers a suite of comfort appliances for the home and office aimed at meeting every
type of heating requirement. DOMOTECK’s mission is to provide its customers with superior products
supported by prompt and professional service.
90% of DOMOTECK’S annual production is exported throughout the world, from New Zealand in the
south to Norway in the north.
DOMOTECK Ltd. and the entire DOMOTECK family are warming hundreds of thousands of homes
throughout the world.
Domoteck Floor Warming Systems Inc.
Address:
885 S Roselle Road, Schaumburg, IL 60193, USA
Tel:
800-959-9276 (Toll-Free)
630-787-0887 (Local)
Fax:
630-787-0572
Website:
http://www.domoteck.us
Email:
service@domoteck.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising