filters - Pentair Partners

filters - Pentair Partners
FILTERS
FILTERS
FILTERS FOR
SWIMMING POOLS
41
42
FILTERS - CARTRIDGE
NOTES:
FILTERS - CARTRIDGE
CLEAN & CLEAR® PLUS FILTERS
FIBERGLASS REINFORCED POLYPROPYLENE TANK
Featured Highlights
•NSF listed
•Superior strength
•Large filter area for increased
dirt capacity
•1-1/2 in., 100% drain clean-out port
•Continuous High Flow™ internal
air relief *
•Base and plumbing kits now available
Clean & Clear
Plus Filter
•Injection molded tank
•Balanced hydraulic flow
•Tension Control™ clamp
•100% factory tested
•Black bulkhead unions
•High Flow manual air relief valve
Clean & Clear ® Plus Filters have a corrosion resistant injection
molded filter tank featuring superior strength and reliability. The
cartridge assembly uses four easy to clean, non-woven, polyester
cartridges. Each filter is supplied with a bulkhead union set for easy
installation.
Ordering Information
Product
Model
Effective Filtration
Area (Sq. Ft.)
Flow Rate 2
(GPM Res)
Flow Rate 3
(GPM Comm)
Turnover Capacity
(In Gallons)
8 Hour
10 Hour
12 Hour
Carton
Qty.
Carton
Wt. (Lbs.)
CLEAN & CLEAR PLUS FILTERS
160310
CCP240
240
90
90
43,200
54,000
64,800
1
60
160340
CCP320
1
320
120
120
57,600
72,000
86,400
1
70
160301
CCP420
1
420
150
150
72,000
90,000
108,000
1
80
160332
CCP520 1
520
150
150
72,000
90,000
108,000
1
90
NSF Listed.
1
Commercial rate is a maximum of .375 GPM sq. ft. of filter area.
3
Residential rate .375 GPM per sq. ft. of filter area.
2
Dimensions and Performance
Note: Actual system flow will depend on plumbing size
and other system components.
Note: Pentair Aquatic Systems does not recommend
flow rates above 150 GPM.
* Integrated continuous High Flow internal air relief is
operational only when there is unobstructed flow in the
circulating system.
Note: Operating Limits – maximum continual operating
pressure of 50 PSI. Pool/spa (bather) applications,
maximum operating water temperature (internal filter)
104°F (40°C).
See page 348 for replacement parts.
43
FILTERS - CARTRIDGE
CLEAN & CLEAR® FILTERS
FIBERGLASS REINFORCED POLYPROPYLENE TANK
Featured Highlights
•NSF listed
•Unionized connections
•Integrated continuous High Flow™ internal air relief *
•Chemical resistant tank body
Clean & Clear Filter
•Lock ring with spring-loaded safety latches
•Coreless cartridge for easy cleaning
•High Flow manual air relief valve
•1 in. drain and wash out
•Single piece base and body design
The Clean & Clear® Filter features a chemical resistant tank with no-tool servicing and a coreless cartridge for easier
cleaning. All models are equipped with easy spin-on unions for plumbing hook-ups. These filters are NSF listed, and
are available in 50, 75, 100, 150, and 200 square foot sizes.
Ordering Information
Product
Model
Effective Filtration
Area (Sq. Ft.)
Flow Rate 1
(GPM Res)
Flow Rate2
(GPM Comm)
Turnover Capacity
(In Gallons)
8 Hour
10 Hour
12 Hour
Carton
Qty.
Carton
Wt. (Lbs.)
CLEAN & CLEAR FILTERS
160314
CC 50
50
50
19
24,000
30,000
36,000
1
15
160315
CC 75
75
75
28
36,000
45,000
54,000
1
26
160316
CC 100
100
100
38
48,000
60,000
72,000
1
33
160317
CC 150
150
150
56
72,000
90,000
108,000
1
35
160318
CC 200
200
150
75
72,000
90,000
108,000
1
35
One GPM per sq. ft. shown recommended flow rate .5 GPM per sq. ft.
1
Dimensions and Performance
Note: Actual system flow will depend
on plumbing size and other system
components.
Note: Pentair Aquatic Systems does not
recommend flow rates above 150 GPM.
* Integrated continuous High Flow
internal air relief is operational only
when there is unobstructed flow in the
circulating system.
Note: Operating Limits – maximum
continual operating pressure of 50
PSI. Pool/spa (bather) applications,
maximum operating water temperature
(internal filter) 104°F (40°C).
44
See page 350 for replacement parts.
2
Commercial rate is a maximum of .375 GPM per sq. ft. of filter area.
FILTERS - CARTRIDGE
CLEAN & CLEAR® RP FILTERS
FIBERGLASS REINFORCED POLYPROPYLENE TANK
Featured Highlights
•Nearly 50% more energy efficient than other single
cartridge filters
•Cartridge is easy to remove and rinse
•Low–force, quick–connect diamond–seal fastens easily
with no tools required
•Chemical resistant tank body
•High–flow manual air relief valve and continuous
internal air relief
•1-1/2 in. drain and wash outashout for quick and
convenient maintenance and winterization
•Easy turn Lock-ring
•Separation Tank debris bag holds up to 20 lbs. of D.E.
The Clean & Clear RP and Posi-Clear RP cartridge filters have a newly developed design, with a side entry port, which
provides nearly 50% more efficiency than any other single cartridge filter available. Inside, the Clean & Clear RP and
Posi-Clear RP have increased cartridge surface consistency to block and trap particles as small as 20 microns. The
D.E. Separation Tank offers 2 x 2 1/2 inch unionized fittings, quarter turn locking-ring for quick and easy access, and
a debris bag that holds up to 20 pounds of D.E.
Ordering Information
Product
Model
Effective Filtration
Area (Sq. Ft.)
Flow Rate 1
(GPM Res)
Flow Rate2
(GPM Comm)
Turnover Capacity
(In Gallons)
8 Hour
10 Hour
12 Hour
Carton
Qty.
Carton
Wt. (Lbs.)
CLEAN & CLEAR RP FILTERS
160354
CCRP 100
100
100
38
48,000
60,000
72,000
1
33
160355
CCRP 150
150
150
56
72,000
90,000
108,000
1
35
160353
CCRP 200
200
150
75
72,000
90,000
108,000
1
35
One GPM per sq. ft. shown recommended flow rate .5 GPM per sq. ft.
1
2
Commercial rate is a maximum of .375 GPM per sq. ft. of filter area.
Dimensions and Performance
Note: Actual system flow will depend
on plumbing size and other system
components.
Note: Pentair Aquatic Systems does not
recommend flow rates above 150 GPM.
* Integrated continuous High Flow
internal air relief is operational only
when there is unobstructed flow in the
circulating system.
Note: Operating Limits – maximum
continual operating pressure of 50
PSI. Pool/spa (bather) applications,
maximum operating water temperature
(internal filter) 104°F (40°C).
See page 349 for replacement parts.
45
FILTERS - CARTRIDGE
DYNAMIC® FILTER SERIES
FOR SPAS, HOT TUBS AND SWIMMING POOLS
Featured Highlights
•Free standing base optional on all but
DSC models
•All cartridges are manufactured of the
finest quality filter media
Dynamic Filter Series
The Dynamic® Filter Series line includes in-line, top load, safety flange lily pad and safety skim filters with automatic
chemical dispensers and a host of features created for the leading spa manufacturers throughout the country.
Ordering Information
Product
Model
Description
Effective
Filtration Area
(Sq. Ft.)
Max
GPM
Plumbing
Size
Filter Dimensions
Height
Diameter
Carton
Qty.
Carton
Wt.
(Lbs.)
DYNAMIC FILTER SERIES II TOP LOAD 2 in. HIGH FLOW FILTERS
R172502J
RTL 25
Slip, 3 oz. cartridge
25
100
2 in. socket
18 in.
8-1/4 in.
4
27
R172503
RTL 75
Slip, 3 oz. cartridge
75
100
2 in. socket
25 in.
8-1/4 in.
4
30
R172504B
RTL 50
Slip, 3 oz. cartridge
50
100
2 in. socket
18 in.
8-1/4 in.
4
28
R172505
RTL 100
Slip, 3 oz. cartridge
100
100
2 in. socket
31-1/2 in.
8-1/4 in.
4
32
DYNAMIC FILTER SERIES III TOP LOAD 2 in. HIGH FLOW FILTERS WITH CHLORINE/BROMINE DISPENSERS
R172523
RCF 25
Slip, 3 oz. cartridge
25
100
2 in. socket
18 in.
8-1/4 in.
4
28
R172535
RCF 50
Slip, 3 oz. cartridge
50
100
2 in. socket
18 in.
8-1/4 in.
4
30
R172503C
RCF 75
Slip, 3 oz. cartridge
75
100
2 in. socket
25 in.
8-1/4 in.
4
32
R172505C
RCF 100
Slip, 3 oz. cartridge
100
100
2 in. socket
31-1/2 in.
8-1/4 in.
4
34
DYNAMIC FILTER SERIES IV FLOATING LILY PAD WEIR FILTERS 1
R172545
DFM 50
Low profile (no weir) short basket
50
100
2 in. socket
17-1/2 in.
8-1/2 in.
4
26
R172664
DFML 25
Lily pad weir, lock ring mount
25
100
2 in. socket
19-3/8 in.
8-1/2 in.
4
27
R172666
DFML 25C
Compact, (not available with
dispenser)
25
100
2 in. socket
12-7/8 in.
8-1/2 in.
4
22
R172668
DFML 25
With chlorine/bromine dispenser
25
100
2 in. socket
19-3/8 in.
8-1/2 in.
4
28
R172670
DFML 35
Lily pad weir, lock ring mount
35
100
2 in. socket
15-1/2 in.
8-1/2 in.
4
24
R172674
DFML 50
Lily pad weir, lock ring mount
50
100
2 in. socket
19-3/8 in.
8-1/2 in.
4
28
DYNAMIC FILTER SERIES IV SAFETY FLANGE FLOATING LILY PAD WEIR FILTERS 2
R172666X
DFML 25C
Compact, (not available with
dispenser)
25
100
2 in. socket
12-7/8 in.
8-1/2 in.
4
22
R172670X
DFML 35
Lily pad weir, lock ring mount
35
100
2 in. socket
15-1/2 in.
8-1/2 in.
4
24
R172674X
DFML 50
Lily pad weir, lock ring mount
50
100
2 in. socket
19-3/8 in.
8-1/2 in.
4
28
DYNAMIC FILTER SERIES IV SAFETY SKIM FILTERS
R172554M
DSF 35
Slip, 3 oz. cartridge
(add face plate kit no.)
35
60
2 in. socket
24-1/8 in.
9-1/2 in.
4
32
R172551
DSF 50
Slip, 3 oz. cartridge
(add face plate kit no.)
50
100
2 in. socket
29 in.
9-1/2 in.
4
36
4
5
1
5
SAFETY FACE PLATE KIT 1
R172555WH
Safety face plate kit, white
SAFETY WALL SKIMMER 3
R172570
46
SWS
Safety wall skimmer only, (add face plate kit no.) complete with diverter plate, vacuum plate
and 90 degree adapter
Product
Description
Carton Qty.
Carton Wt. (Lbs.)
ACCESSORIES FOR DYNAMIC FILTER SERIES II, III, IV, V
R172452
Free standing base for Dynamic Filter Series II and III
Bulk
R172540
Chlorine/Bromine Dispenser for Dynamic Filter Series II and III
Bulk
R172560
Chlorine/Bromine Dispenser for Dynamic Filter Series IV Skim
Bulk
R172562
Chlorine/Bromine Dispenser w/basket for DFM 50
Bulk
R172662
Chlorine/Bromine Dispenser w/basket for DFML 25, 35, 50
Bulk
Safety flange kit, dark grey
Bulk
Safety flange kit, sterling silver
Bulk
R172691DGK
R172691SK
FILTERS - CARTRIDGE
DYNAMIC® FILTER SERIES (CONT’D)
FILTER NICHE AND COVER FOR DYNAMIC FILTER SERIES II AND III
R172542BLK
Black
4
6
R172542SS
Sterling silver
4
6
R172542WH
White
4
6
FILTER NICHE COVER ONLY
R172611BK
Black
Bulk
R172611SS
Sterling silver
Bulk
R172611WH
White
Bulk
Note: Niche covers can be imprinted with your company name or logo. Minimum quantity 96 or more. $35.00 net first run die charge.
Add 15¢ to dealer price. Add “i” after order number.
All available in white. For sterling silver top add “SS” to order number. For dark grey add “DG.”
1
All available in white. For sterling silver top add “SX” to order number. For dark grey add “DGX.”
2
When ordering R172551, R172554M or R172570 you must also select a Face Plate Kit.
3
With filter gauge, add 4-1/4 in. to height.
4
RLT-25
DMFL-25
DFS-50
RCF-25
SWS
DMFL-25
See page 352–357 for replacement parts.
47
FILTERS - CARTRIDGE
SYSTEM 3® MODULAR MEDIA FILTERS
SM SERIES FILTERS
Featured Highlights
•Typical Installation – Inground pools, inground hot
tubs, and water features
•Quality Construction – Durable two-piece tank housing
constructed of Dura-Glas™, Sta-Rite’s industry leading
glass reinforced composite resin
•Safer – Posi-Lok™ Clamps provides safer, easy access
to tank internals
• Innovative Design – The innovative balanced flow
design first introduced with the System 3 Mod Media is
still the standard of the industry
•Low Maintenance – Complete media coverage
combined with shallow pleats means greater dirt
holding capabilities, resulting in longer filter cycles and
less cleaning
System 3 Modular Media Filter SM
Series
•Quick Service – The shallow pleat design allows you
to simply hose off the elements in a matter of minutes,
making servicing a snap
•Dual Drain Plugs – Side plug available for plumbing to
waste, while the bottom plug will drain entire filter
With the System 3 Modular Media Filter, Sta-Rite brings you the product that makes Ultra-Capacity Filtration™ a
reality. No longer simply “­ cartridges,” Sta-Rite’s advanced tech­nology has brought an entirely new class of filtration
to the industry. Sta-Rite’s modular media concept incorporates the latest in media science, perfectly balanced flow,
and an integral manifold design: namely, Ultra-Capacity Filtration. This filtration concept puts totally care-free
operation within reach of today’s pool owners. Modular Filter Tanks allows for quick change of filter medias without
changing the tank. Contemporary style and matte black finish looks attractive in any pool setting.
Ordering Information
Product
Effective Filter
Area (Sq. Ft.)
Turnover Capacity (In Gallons)
(Flow Rate x 60 x Hours)
1
Flow Rated GPM
(Sq. Ft.)
6 Hour
8 Hour
10 Hour
Tank Port
Size
Carton
Wt. (Lbs.)
SYSTEM 3 MODULAR MEDIA FILTER - SM SERIES
S7M120
300
50–100
18–36,000
24–48,000
30–60,000
2 in.
120
S7M400
1
400
50–115
18–41,000
24–55,000
30–69,000
2 in.
125
S8M150
1
450
50–124
18–45,000
24–60,000
30–74,000
2 in.
147
S8M500
1
500
50–130
18–46,000
24–62,400
30–78,000
2 in.
150
Based on NSF rated flow range of .333 GPM per square foot for the
S7M120.
1
.288 GPM per square foot for the S7M400, .275 GPM for the S8M150 and
.26 GPM per square foot for the S8M500.
48
Note: No backwash valve required.
Note: Operating Limits – maximum continual operating pressure of
50 PSI. Pool/spa (bather) applications, maximum operating water
temperature (internal filter) 104°F (40°C).
Ordering Information
Product
Description
Carton Wt. (Lbs.)
ACCESSORIES FOR SYSTEM 3 MODULAR MEDIA FILTER - SM SERIES
PKG 188
Union x 2 in. Slip Adapter - Pkg. of 2
1
PKG 189
Union x 2 in. FPT Adapter - Pkg. of 2
1
77703-0100
Union x 1-1/2 in. FPT Adapter - Pkg. of 2
1
77703-0101
Union x 1-1/2 in. Slip Adapter - Pkg. of 2
1
25021-0200S
100 sq. ft. Inner Replacement Module for S7M120
9
25022-0201S
200 sq. ft. Outer Replacement Module for S7M120
21
25021-0223S
136 sq. ft. Inner Replacement Module for S7M400
11
25022-0224S
264 sq. ft. Outer Replacement Module for S7M400
24
25021-0202S
191 sq. ft. Inner Replacement Module for S8M150
18
25022-0203S
259 sq. ft. Outer Replacement Module for S8M150
27
25021-0224S
209 sq. ft. Inner Replacement Module for S8M500
19
25022-0225S
291 sq. ft. Outer Replacement Module for S8M500
28
25021-0021
Modular Media Conversion Kit - S7M120/S7M400 (Order Modules Separately)
4
25021-0025
Modular Media Conversion Kit - S8M150/S8M500 (Order Modules Separately)
5
FILTERS - CARTRIDGE
SYSTEM 3® MODULAR MEDIA FILTERS (CONT’D)
SM SERIES FILTERS
Dimensions and Performance
DIMENSION
Catalog Number
C
D
E
S7M120/S7M40028-1/2 42
A
B
7
36
50
S8M150/S8M500 32-1/242-1/4
8
40
50
A=width
B = height
C = number of clamps
D = area (width) needed to take off clamps
E = area (height) needed to remove top half of tank
All dimensions shown in inches.
See page 358 for replacement parts.
49
FILTERS - CARTRIDGE
SYSTEM:2™ MODULAR MEDIA FILTERS
PLM SERIES FILTERS
Featured Highlights
•Typical Installation – aboveground pools, inground pools,
and inground hot tubs
•Quality Construction – Durable two-piece tank housing
constructed of rugged ABS thermoplastic to ensure a
long-lasting tank life
•Easy Access – Posi-Ring® Locking Ring provides safer,
fast access to tank internals
•Innovative Design – The innovative balanced flow design
first introduced with the System 3 Mod Media filter is
now available in the smaller System:2 filter, virtually
maintenance-free operation for pools of all sizes
•Low Maintenance – Complete media coverage combined
with shallow pleats means greater dirt holding
capabilities, resulting in longer filter cycles and less
cleaning
System:2 Modular Media Filters
PLM Series
•Large Drain Plug – Filter includes 2 in. NPT Drain ports,
which are provided with reducer bushing and 1-1/2 in.
drain plug
Sta-Rite’s modular media filtration is the perfect match for both the inground and aboveground pool markets.
Advances in media ­technology and balanced flow design provide dirt-loading capabilities up to 15 times greater
than sand filters of equivalent size. Virtually maintenance-free ­operation for today’s pool owner. The small diameter
footprint makes the System:2 filter a perfect fit for new and retrofit installations.
Modular Filter Tanks allows for quick change of filter medias without changing the tank. Contemporary style and
matte black finish looks attractive in any pool setting.
Ordering Information
Product
Effective Filter
Area (Sq. Ft.)
1
Flow Rated
GPM (Sq. Ft.)
Turnover Capacity (In Gallons)
(Flow Rate x 60 x Hours)
6 Hour
8 Hour
Tank Port
Size
Carton
Wt. (Lbs.)
23–60,000
2 in.
41
10 Hour
SYSTEM:2 MODULAR MEDIA FILTER - PLM SERIES
PLM100
100
38–100
14–36,000
18–48,000
PLM125
125
47–125
17–45,000
22–60,000
28–75,000
2 in.
42
PLM150
150
56–150
20–54,000
27–72,000
34–90,000
2 in.
43
PLM175
175
66–150
24–54,000
31–72,000
39–90,000
2 in.
44
PLM200
200
75–150
27–54,000
36–72,000
45–90,000
2 in.
45
PLM300
300
113–150
41–54,000
54–72,000
68–90,000
2 in.
53
Based on NSF recommended flow rate for commercial at .375 GPM per
square foot.
Note: No backwash valve required.
1
50
Note: Operating Limits – maximum continual operating pressure of
50 PSI. Pool/spa (bather) applications, maximum operating water
temperature (internal filter) 104°F (40°C).
Ordering Information
Product
Description
Carton Wt. (Lbs.)
ACCESSORIES FOR SYSTEM:2 MODULAR MEDIA FILTER - PLM SERIES
27002-0100S
100 Sq. Ft. Replacement Module for PLM100
11
27002-0125S
125 Sq. Ft. Replacement Module for PLM125
11.5
27002-0150S
150 Sq. Ft. Replacement Module for PLM150
12
27002-0175S
175 Sq. Ft. Replacement Module for PLM175
13
27002-0200S
200 Sq. Ft. Replacement Module for PLM200
14
27002-0300S
300 Sq. Ft. Replacement Module for PLM 300
19
U78-820P
27001-0130S
2 in. x 1-1/2 in. Pipe Reducer Bushing
Spring Check Valve
FILTERS - CARTRIDGE
SYSTEM:2™ MODULAR MEDIA FILTERS (CONT’D)
PLM SERIES FILTERS
8 oz.
1
Dimensions and Performance
PLM300
All dimensions shown in inches.
PLM100,
PLM125,
PLM150,
PLM175,
PLM200,
PLM300
See page 359 for replacement parts.
51
FILTERS - CARTRIDGE
POSI-CLEAR RP® FILTERS
FIBERGLASS REINFORCED POLYPROPYLENE TANK
Featured Highlights
•NSF listed
•Unionized connections
•Integrated continuous High Flow™ internal air relief *
•Chemical resistant tank body
•Lock ring with spring-loaded safety latches
•Coreless cartridge for easy cleaning
•High Flow manual air relief valve
•1 in. drain and wash out
•Single piece base and body design
The Posi-Clear RP Filter features a chemical resistant tank with no-tool
servicing and a coreless cartridge for easier cleaning. All models are
equipped with easy spin-on unions for plumbing hook-ups. These filters are
NSF listed, and are available in 100, 150, and 200 square foot sizes.
Ordering Information
Product
Model
Effective Filtration
Area (Sq. Ft.)
Flow Rate 1
(GPM Res)
Flow Rate2
(GPM Comm)
Turnover Capacity
(In Gallons)
8 Hour
10 Hour
12 Hour
Carton
Qty.
Carton
Wt. (Lbs.)
POSI-CLEAR RP FILTERS
160351
PXCRP100
100
100
38
48,000
60,000
72,000
1
33
160352
PXCRP150
150
150
56
72,000
90,000
108,000
1
35
160350
PXCRP200
200
150
75
72,000
90,000
108,000
1
35
One GPM per sq. ft. shown recommended flow rate .5 GPM per sq. ft.
1
2
Commercial rate is a maximum of .375 GPM per sq. ft. of filter area.
Dimensions and Performance
Note: Actual system flow will depend
on plumbing size and other system
components.
Note: Pentair Aquatic Systems does not
recommend flow rates above 150 GPM.
* Integrated continuous High Flow internal
air relief is operational only when there is
unobstructed flow in the circulating system.
Note: Operating Limits – maximum
continual operating pressure of 50 PSI.
Pool/spa (bather) applications, maximum
operating water temperature (internal
filter) 104°F (40°C).
52
See pages 360-361 for replacement parts.
Featured Highlights
FILTERS - D.E.
FNS® PLUS FILTERS
FIBERGLASS REINFORCED POLYPROPYLENE MATERIAL, VERTICAL GRID, D.E.
FNS® Plus filters are fiberglass
reinforced polypropylene of advanced
chemical resistant materials for
superior strength and reliability. The
top manifold design features the
Service-Ease grid pack for convenient
one-at-a-time grid servicing.
•Superior strength
•Service-Ease™ grid pack
•Continuous High Flow™ internal air
relief *
•100% factory tested
•Top-to-bottom backwash
•High Flow manual air relief valve
•Tension ControlTM clamp
FNS Plus Filter
•Black valves and plumbing
•1-1/2 in. bottom clean out port
•7-1/2 in. centerline bulkhead fittings
Ordering Information
Product
Model
Effective
Filtration Area
(Sq. Ft.)
Turnover Capacity (In Gallons)
Flow Rate 1
(GPM)
8 Hour
10 Hour
12 Hour
D.E. Required Carton
(Lbs.)
Qty.
Carton
Wt. (Lbs.)
FNS PLUS FILTERS
180006
FNSP24
24
48
23,040
28,800
34,560
2.4
1
60
180007
FNSP36
36
72
34,560
43,200
51,840
3.6
1
70
180008
FNSP48
48
96
46,080
57,600
69,120
4.8
1
80
180009
FNSP60
60
120
57,600
72,000
86,400
6.0
1
90
3
FNS PLUS VALVE OPTIONS
2
263079
2 in. PVC Slide valve w/o bulkhead fitting
1
261049
2 in. HiFlow valve, no plumbing
1
7
261142
2 in. HiFlow valve with plumbing for FNS, FNS Plus, NSP filters
1
11
261152
2 in. MPV, threaded for FNS, FNS Plus, NSP filters
1
10
263064
Push pull valve, 7-1/2 in. Center, Almond PVC
1
6
261177
1-1/2 in. MPV, threaded for FNS, FNS Plus, NSP filters
1
7
263081
Valve for D.E., inlet port on bottom, Pentair 2 in. unions glued on
Flow rate is based on 2.0 GPM per sq. ft. of filter area. Actual system
flow will depend on plumbing size and other system components.
1
Valves must be purchased separately.
2
Dimensions and Performance
* Integrated continuous High Flow
internal air relief is operational only
when there is unobstructed flow in
the circulating system.
Note: Operating Limits – maximum
continual operating pressure of 50
PSI. Pool/spa (bather) applications,
maximum operating water
temperature (internal filter) 104°F
(40°C).
See pages 367 for replacement parts.
53
FILTERS - D.E.
EASYCLEAN™ FILTERS
FIBERGLASS REINFORCED POLYPROPYLENE TANK
The EasyClean™ Filter features
a chemical resistant tank with
no-tool servicing and a coreless
cartridge for easier cleaning. All
models are equipped with easy
spin-on-unions for plumbing
hook-ups.
Featured Highlights
•NSF listed
•Unionized connections
•Integrated continuous High Flow™
internal air relief *
•Chemical resistant tank body
•Lock ring with spring-loaded
safety latches
•Coreless cartridge for easy cleaning
•High Flow manual air relief valve
•1 in. drain and wash out
•Single piece base and body design
EasyClean Filter
Ordering Information
Product
Model
Effective
Filtration Area
(Sq. Ft.)
Vertical
Clearance 1
Flow Rate 2
(GPM)
188614
EC60
15
39 in.
60
1.5
188615
EC90
30
76 in.
90
3.0
D.E.
Required
Turnover Capacity (In Gallons)
10 Hour
12 Hour
Carton
Qty.
Carton
Wt. (Lbs.)
28,000
36,000
43,000
1
26
43,200
54,000
64,800
1
35
8 Hour
EASYCLEAN FILTERS
Required clearance to remove filter elements.
1
Maximum flow rate.
2
Dimensions and Performance
Note: Actual system flow will depend on plumbing
size and other system components.
Note: Pentair Aquatic Systems does not recommend
flow rates above 150 GPM.
* Integrated continuous High Flow internal air relief
is operational only when there is unobstructed flow
in the circulating system.
Note: Operating Limits – maximum continual
operating pressure of 50 PSI. Pool/spa (bather)
applications, maximum operating water temperature
(internal filter) 104°F (40°C).
Dimension Table
54
Model
A Dim
B Dim
188614
25-1/2 in.
39 in.
188615
40-1/2 in.
76 in.
See page 364 for replacement parts.
FILTERS - D.E.
QUAD D.E.® FILTERS
CARTRIDGE STYLE FILTER
Featured Highlights
•Four large-capacity cartridges provide maximum filter
surface area for greater dirt-trapping capacity and
longer periods between cleanings
•Innovative internal flow path ensures optimum filtration
and backwashing efficiency
•Chemical resistant, fiberglass reinforced polypropylene
tank for exceptional strength and long life
•Easily removable cartridge elements make
maintenance fast and easy
•Water flows through the Quad D.E.® so efficiently that
your pump will use less energy
The Highest Water Clarity with the Lowest Amount of Fuss. Quad D.E.®
combines the finest filtration available for the most sparkling clear water
with the convenience and easy-cleaning features usually found only in
a cartridge filter. Four easily accessible and removable D.E. cartridges
simplify maintenance and save time.
Product
Model
Effective
Filtration Area
(Sq. Ft.)
Quad D.E. Filter
Ordering Information
Turnover Capacity (In Gallons)
Flow Rate
(GPM)
8 Hour
10 Hour
12 Hour
D.E. Required Carton
(Lbs.)
Qty.
Carton
Wt. (Lbs.)
QUAD D.E. FILTERS
188592
Quad D.E. 60
60
120
57,600
72,000
86,400
6.0
1
70
188593
Quad D.E. 80
80
160
76,800
96,000
115,200
8.0
1
80
188594
Quad D.E. 100
100
160
76,800
96,000
115,200
10.0
1
90
3
QUAD D.E. VALVE OPTIONS
261173
1-1/2 in. MPV, for Triton and Quad D.E. filters (SM 10-3)
1
263079
2 in. PVC Slide valve w/o plumbing, for D.E. & sand filters
1
7
261049
2 in. HiFlow valve, no plumbing
1
11
261050
2 in. HiFlow w/plumbing, for Triton and Quad D.E. filters
1
10
261055
2 in. MPV, for Triton and Quad D.E. filters (SM 20-3)
1
5
263064
Push pull valve, 7-1/2 in. Center, Almond PVC
1
4
270100
Adaptor Kit (For no valve assembly)
1
263080
Valve for D.E., inlet port on bottom, Pentair 2 in. unions glued on
Valves must be purchased separately.
1
1
Note: Operating Limits – maximum continual operating pressure of 50 PSI. Pool/spa (bather)
applications, maximum operating water temperature (internal filter) 104°F (40°C).
Dimensions and Performance
See page 368 for replacement parts.
55
FILTERS - D.E.
SYSTEM:2™ MODULAR D.E. FILTERS
PLD SERIES FILTERS
Featured Highlights
•Typical Installations – Inground pools and inground hot tubs
•Quality Construction – Durable two-piece tank housing
constructed of rugged ABS thermoplastic to ensure a longlasting tank life
•Easy Access – Posi-Ring® Closure provides safer, fast
access to tank internals
•Innovative Design – The innovative balanced flow design
first introduced with the System 3 Mod Media filter is
now available in the smaller System:2 filter. Virtually
maintenance-free operation for pools of all sizes
•Low Maintenance – Complete media coverage combined
with shallow pleats means greater dirt holding capabilities,
resulting in longer filter cycles and less cleaning
System:2 Modular D.E. Filter
PLD Series
•Modular Filter Tanks – Allows for quick change of filter
medias without changing the tank
Sta-Rite delivers the benefits of D.E. filtration in a variation of their proven modular media technology. A single
replaceable grid delivers water of superior quality without the complex workings of other D.E. filters. Tank and
one-piece grid design make this filter virtually maintenance-free. Contemporary style and matte black finish
looks attractive in any pool setting. The small diameter footprint makes the System:2 filter a perfect fit for new
and retrofit installations. Filter includes 2 in. NPT Drain ports, which are provided with reducer bushing and
1-1/2 in. drain plug.
Ordering Information
1
Turnover Capacity (Gallons)
(Flow Rate x 60 x Hours)
Effective
Filter Area
(Sq. Ft.)
Flow Rated
at 1–2 GPM
(per Sq. Ft.)
PLD50
30
30–60
11–22,000
14–29,000
PLD70
36
36–72
13–26,000
17–35,000
Product
6 Hour
8 Hour
2
Tank
Port
Size
D.E.
Required
(Lbs.)
Carton
Wt. (Lbs.)
18–36,000
2 in.
63
37
22–43,000
2 in.
4
38
10 Hour
SYSTEM:2 MODULAR D.E. FILTER - PLD SERIES
Based on NSF recommended flow rate for commercial at 1–2 GPM
per square foot.
1
Do not use more D.E. than shown here. Mixed results with D.E.
alternatives.
2
PLD50 requires more D.E. than the PLD70 because of precoat design
and flow characteristics!
3
56
Note: Operating Limits – maximum continual operating pressure of
50 PSI. Pool/spa (bather) applications, maximum operating water
temperature (internal filter) 104°F (40°C).
Ordering Information
Product
Description
Carton Weight (Lbs.)
ACCESSORIES FOR SYSTEM:2 MODULAR D. E. FILTER - PLD SERIES
27002-0030S
30 sq. ft. Replacement Module for PLD50
10
27002-0036S
36 sq. ft. Replacement Module for PLD70
10
2 in. x 1-1/2 in. Pipe Reducer Bushing
1
Spring Check Valve
1
U78-820P
27001-0130S
FILTERS - D.E.
SYSTEM:2™ MODULAR D.E. FILTERS (CONT’D)
PLD SERIES FILTERS
Dimensions and Performance
All dimensions shown in inches.
See page 379 for replacement parts.
57
FILTERS - D.E.
SYSTEM:2™ MODULAR D.E. FILTERS
PLDE SERIES FILTERS
Featured Highlights
•Typical Installations – Inground pools and inground hot tubs
•Quality Construction – Durable two-piece tank housing
constructed of rugged ABS thermoplastic to ensure a longlasting tank life
•Easy Access – Posi-Ring® Locking Ring provides safer, easy
access to tank internals
•Innovative Design – The innovative, balanced-flow design
– first introduced with the System 3 Mod Media filter – is
now available in the smaller System:2 filter. Virtually
maintenance-free operation for pools of all sizes.
•A Perfect Fit – The small diameter footprint makes the
System:2 filter a perfect fit for new and retrofit installations
•Modular Filter Tanks – Allows for quick change of filter
medias without changing the tank plumbing
System:2 Modular D.E. Filters
PLDE Series
Sta-Rite delivers the benefits of D.E. filtration in a variation of their proven modular media technology. A single
replaceable grid delivers water of superior quality without the complex workings of other D.E. filters. This
innovative one-piece design is fully backwashable and can be plumbed with or without a backwash valve. 2
in. union valves are included for installations electing not to use a backwash valve. For deep-down cleaning,
simply remove the filter lid and hose off in place. No more hassle of tearing down the grid assembly for
cleaning and servicing. Contemporary style and matte black finish looks attractive in any pool setting.
Ordering Information
Product
Effective
Filter Area
(Sq. Ft.)
Flow Rated 1
at 1–2 GPM
(per Sq. Ft.)
Turnover Capacity (Gallons)
(Flow Rate x 60 x Hours)
6 Hour
8 Hour
Tank Port
Size
D.E.2
Required
(Lbs.)
Carton
Wt. (Lbs.)
22–43,000
2 in.
5.4
38
29–57,600
2 in.
7.2
46
10 Hour
SYSTEM:2 MODULAR D.E. FILTER - PLDE SERIES
PLDE36
36
36–72
13–26,000
17–35,000
PLDE48
48
48–96
17–34,000
23–46,000
PLDE VALVE OPTIONS
18202-0250
ABS 6-Position Valve with Union Connections – 1-1/2 in. Valve Port
5
18201-0300
ABS 6-Position Valve with Union Connections – 2 in. Valve Port
8
263053
VLV Push Pull, 7.81 in. center
262509
Valve with filter inlet port on top, no fittings, only valve
Based on NSF recommended flow rate for commercial at 1–2 GPM per
square foot.
1
Do not use more D.E. than shown here. Mixed results with D.E.
alternatives.
2
58
3
Valves must be purchased separately.
3
Note: Operating Limits – maximum continual operating pressure of
50 PSI. Pool/spa (bather) applications, maximum operating water
temperature (internal filter) 104°F (40°C).
Ordering Information
Product
Description
Carton Weight (Lbs.)
ACCESSORIES FOR SYSTEM:2 MODULAR D.E. FILTER - PLDE SERIES
27002-0036S
36 sq. ft. Replacement Module for PLD50, PLDE36
10
27002-0048S
48 sq. ft. Replacement Module for PLDE48
11
2 in. Union Half x 2 in. Slip - Package of 2
1
2 in. Union Half x 1-1/2 in. Slip - Package of 2
1
PKG 188
77703-0101
FILTERS - D.E.
SYSTEM:2™ MODULAR D.E. FILTERS (CONT’D)
PLDE SERIES FILTERS
Dimensions and Performance
Product
For Pools Up To (Gal.)
8 Hr. Turnover
Filter Area
Sq. Ft.
Original Flow Rate
(GPM)
D.E. Required
(Lbs.)
PLDE SERIES FILTER PERFORMANCES
PLDE36
35,000
36
54
5.4
PLDE48
46,000
48
72
7.2
PLDE48
PLDE36
All dimensions
shown in inches.
See page 380 for replacement parts.
59
FILTERS - D.E.
SYSTEM 3® D.E. FILTERS
SD SERIES FILTERS
Featured Highlights
•Typical Installations – Inground pools, inground hot tubs,
and water features
•Quality Construction – Durable two-piece tank housing
constructed of Dura-Glas™, Sta-Rite’s industry leading
glass-reinforced composite resin
•Safer – Posi-Lok™ Clamps provides safer, easy access to
tank internals
•Innovative Design – 2 in. plumbing throughout combined
with Sta-Rite’s exclusive rectangular grid system provides
superior D.E. filtration
•Low Maintenance – Superior backwash capabilities means
less manual cleaning of the grids
•Dual Drain Plugs – Side plug assembly includes 1-1/2 in.
NPT port for direct discharge plumbing
•Sleek Looks – Contemporary style and matte black finish
looks attractive in any pool setting
System 3 D.E. Filters
SD Series
D.E. is historically the media of choice for the designers of some of the largest and most beautiful pools in the
world. It is now more practical for all backyard pools as well. System 3 brings you the proven performance of StaRite’s diatomaceous earth media in the world’s easiest-to-operate filter. The greater cycle times and ­minimized
maintenance of the System 3, coupled with Sta-Rite’s ­superior grid system, gives you the finest D.E. filter available.
Ordering Information
Product
Effective
Filter Area
(Sq. Ft.)
Flow Rated 1
at 1–2 GPM
(per Sq. Ft.)
Turnover Capacity (Gallons)
(Flow Rate x 60 x Hours)
6 Hour
8 Hour
10 Hour
Tank
Port
Size
D.E.2
Required
(Lbs.)
Carton
Wt. (Lbs.)
SYSTEM 3 D. E. FILTERS - SD SERIES
S7D75
37
37–74
13–27,000
18–36,000
22–44,000
2 in.
3.7
112
S8D110
53
53–106
19–38,000
26–51,000
32–64,000
2 in.
5.3
136
SD SERIES VALVE OPTIONS 3
18202-0150
ABS 6-Position Valve with Union Connections – 1-1/2 in. Valve Port
5
18201-0200
ABS 6-Position Valve with Union Connection – 2 in. Valve Port
8
263053
VLV Push Pull, 7.81 in. center
262508
Sta-Rite version for System 3 D.E. and Sand, inlet on bottom, with Sta-Rite offset
adapters glued on
ACCESSORIES FOR SYSTEM 3 MODULAR D. E. FILTER - SD SERIES
25021-1021
DE Conversion Kit – S7D75 - Grid Assembly and Valve Sold separately
18
25021-1025
DE Conversion Kit – S8D110 - Grid Assembly and Valve Sold separately
20
Based on NSF recommended flow rate for commercial at 1–2 GPM
per square foot.
1
Do not use more D.E. than shown here. Mixed results with D.E.
alternatives.
2
60
Valves must be purchased separately.
3
Note: Operating Limits – maximum continual operating pressure of
50 PSI. Pool/spa (bather) applications, maximum operating water
temperature (internal filter) 104°F (40°C).
Dimensions and Performance
FILTERS - D.E.
SYSTEM 3® D.E. FILTERS (CONT’D)
SD SERIES FILTERS
18202-0150
1-1/2 in. MULTIPORT VALVE
18201-0200
2 in. MULTIPORT VALVE
DIMENSION
Catalog Number
A
B
C
D
E
S7D75
28-1/242 7 3650
S8D110
32-1/242-1/4 8
40 50
A=width
B = height
C = number of clamps
D = area (width) needed to take off clamps
E = area (height) needed to remove top half of tank
All dimensions shown in inches.
All dimensions shown in inches.
See page 381 for replacement parts.
61
FILTERS - D.E.
SYSTEM 3® MODULAR D.E. FILTERS
SMD SERIES FILTERS
Featured Highlights
•Typical Installations – Inground pools, inground hot
tubs, and water features
•Quality Construction – Durable two-piece tank housing
constructed of Dura-Glas™, Sta-Rite’s industry leading
glass-reinforced composite resin
•Safer – Posi-Lok™ Clamps provides safer, easy access
to tank internals
•Modular Filter Tanks – Allows for quick change of filter
medias without changing the tank
•Low Maintenance – Superior backwash capabilities
means less manual cleaning of the grids
•Dual Drain Plugs – Side plug assembly includes 1-1/2
in. NPT port for direct discharge plumbing
•Sleek Looks – Contemporary style and matte black
finish looks attractive in any pool setting
System 3 Modular D.E. Filters
SMD Series
Sta-Rite is proud to bring you the proven technology of System 3 Modular Media into the world of D.E. With it’s
perfectly balanced flow and integral manifold design, the System 3 Modular D.E. filter brings pool filtration to new
heights. Available in 2 sizes, 60 and 72 sq. ft., System 3 Modular Media D.E. filtration will bring years of sparkling
clear water to your customer’s pool or spa. For cleaning, simply remove filter lid and hose off in place. No more
hassle of tearing down the grid assembly for cleaning and servicing. The balanced flow design allows for a constant
D.E. cake on the entire module, assuring full optimization of the module and longer cycles between cleanings.
Ordering Information
Product
Effective Filter
Area
(Sq. Ft.)
Turnover Capacity (Gallons)
(Flow Rate x 60 x Hours)
1
Flow Rated
at 1–2 GPM
(per Sq. Ft.)
6 Hour
8 Hour
10 Hour
Tank
Port
Size
D.E.
Required
(Lbs.)
Carton
Wt. (Lbs.)
SYSTEM 3 MODULAR D.E. FILTERS - SMD SERIES
S7MD60
60
60–120
21–32,400
28–43,200
36–54,000
2 in.
9
115
S7MD72
72
72–144
25–38,880
34–51,800
43–64,800
2 in.
11
117
SMD SERIES VALVE OPTIONS
18201-0300
263053
ABS 6-Position Valve with Union Connections – 2 in. Port Valve
8
VLV Push Pull, 7.81 in. center
ACCESSORIES FOR SYSTEM 3 MODULAR D.E. FILTER - SMD SERIES
25023-0160S 60 sq. ft. Replacement D.E. Element
20
25023-0172S 72 sq. ft. Replacement D.E. Element
21
PKG 188
Union x 2 in. Slip Adapter – Pkg. of 2
1
PKG 189
Union x 2 in. FPT Adapter – Pkg. of 2
1
23910-1100S System 3 Modular D.E. Conversion Kit (replacement element required)
3
Based on NSF recommended flow rate for commercial at 1–2 GPM per square foot.
1
Note: Operating Limits – maximum continual operating pressure of 50 PSI. Maximum operating water temperature (internal filter) 104°F (40°C).
62
Dimensions and Performance
FILTERS - D.E.
SYSTEM 3® MODULAR D.E. FILTERS (CONT’D)
SMD SERIES FILTERS
18201-0300
2 in. MULTIPORT VALVE
14935-0300
2 in. SLIDE VALVE
DIMENSION
Catalog Number
A
B
C
D
E
S7MD60
28-1/242
7
36 50
S7MD72
28-1/242
7
36 50
A=width
B = height
C = number of clamps
D = area (width) needed to take off clamps
E = area (height) needed to remove top half of tank
All dimensions shown in inches.
See page 383 for replacement parts.
63
FILTERS - D.E.
SMBW 4000 SERIES™ FILTERS
SHEET MOLDED FIBERGLASS TANK WITH BACKWASH VALVES
Featured Highlights
•Maximum Operating Pressure 50 psi
•Corrosion-resistant 20 in. diameter fiberglass filter
tank for strength and durability
•Spiro-Mite grid design provides high efficiency filtration
and longer filter cycles
•Innovative clamp ring design is proven to be safer,
strong and reliable. It allows for quick and easy access
to internal components
•2 in. plumbing connections provide maximum flow
Sheet molded fiberglass tank, 2 in. threaded female
connections with PPO Resin rotary backwash valve.
SMBW 4000 Series Filter
Ordering Information
Product
Model
Effective
Filtration Area
(Sq. Ft.)
Flow Rate
(GPM)
Turnover Capacity (In Gallons)
8 Hour
10 Hour
12 Hour
D.E.
Required
(Lbs.)
Carton
Qty.
Carton
Wt. (Lbs.)
SMBW 4000 FILTERS WITH BACKWASH VALVE
011555
SMBW 4048
47
94
45,120
56,400
67,680
4.8
1
89
147411
SMBW 4060
58
116
55,680
69,600
83,520
6.0
1
110
Note: Operating Limits – maximum continual operating pressure of 50 PSI. Pool/spa
(bather) applications, maximum operating water temperature (internal filter) 104°F (40°C).
Dimensions and Performance
64
See page 369 for replacement parts.
Dimensions and Performance
Efficient removal of spent D.E. and debris
from backwash water – allows a closed loop
system which returns backwash water to
the pool. Constructed of glass-reinforced
thermoplastic for years of corrosion-free
performance. Eliminates disposal problems
for D.E. material.
FILTERS -ACCESSORIES
D.E. SEPARATION TANK
Ordering Information
Pipe For
Filters
Product
Connections
Carton Wt.
(Lbs.)
D.E. SEPARATION TANK
D.E. Separation
Tank
60SEP
To 60 sq. ft.
1-1/2 in. NPT
25
Note: Separation tanks include
polypropylene bag, air relief plug
and clamp assembly.
Valves must be purchased
separately.
1
See page 399 for replacement parts.
SEPARATION TANK 100
Dimensions and Performance
Quarter turn locking-ring provides quick
and easy access for removing debris bag.
Offers 2 x 2-1/2 inch unionized fittings.
Debris bag holds up to 20 lbs of D.E.
Ordering Information
Product
Pipe For
Filters
300005
100 sq. ft.
Connections
Carton Wt.
(Lbs.)
D.E. SEPARATION TANK
2 x 2-1/2 in. SLIP
30
See page 399 for replacement parts.
65
FILTERS - SAND
TRITON® II, TAGELUS® & SAND DOLLAR® FILTERS
WITH CLEARPRO TECHNOLOGY®
Featured Highlights
• All the same, great features of
the Triton® II, Tagelus® and Sand
Dollar® Filters
• Provides superior water quality
Triton II Filter
(Unions not included)
Tagelus Filter
Sand Dollar Filter
Ordering Information
Product
Model
Effective
Filtration
Area
(Sq. Ft.)
140212
TR 60
3.14
Turnover Capacity (In Gal.)
Max.
Press
(PSI)
50
Flow
Flow
Rate Rate (GPM
(GPM) Comm)
8
Hour
10
Hour
Filter Media
12
Hour
Pea
Gravel
Required
(Lbs.)
Sand
Req’d
(Lbs.)
All
Sand
Req’d
(Lbs.)
Ctn Qty.
Ctn
Wt.
(Lbs.)
45,360
75
250
325
1
40
43,200
N/A
N/A
325
1
30
54,000
N/A
N/A
350
1
76
TRITON II SAND FILTERS
63
63
30,240
37,800
TAGELUS FILTERS
145201
TA 60D
3.1
50
60
60
28,800
36,000
SAND DOLLAR FILTERS
145300
SD 80
3.5
50
75
75
36,000
45,000
Dimensions and Performance
Triton II Side Mount Filter
66
A =
B =
C =
D =
35-1/2 in.
24-1/2 in.
13-5/8 in.
37-1/2 in.
Tagelus Top Mount Filter
Sand Dollar Top Mount Filter
A = 47 in.
B = 37 in.
C = 19-1/2 in.
A = 47-7/8 in.
C = 34 in.
FILTERS - SAND
SAND DOLLAR® TOP MOUNT FILTER
THERMOPLASTIC TANK WITH CLAMP STYLE MULTIPORT VALVE
Featured Highlights
• Six-position, top-mounted multiport valve
• Combination water and sand drain makes
servicing and winterizing fast and easy
The one piece Sand Dollar ® filter features a clamp style,
six-position multiport valve. Special lateral design
provides superior flow characteristics and long filter
cycles for economical operation.
Sand Dollar Top Mount Filter
Ordering Information
Product
Model
Effective
Max.
Flow Rate
Filtration Area Pressure
(GPM)
(Sq. Ft.)
(PSI)
Turnover Capacity (In Gallons)
8 Hour
10 Hour
12 Hour
All Sand
Required
(Lbs.)
Carton
Qty.
Carton
Wt.
(Lbs.)
SAND DOLLAR FILTERS
145315
SD 35
1.4
30
35
16,800
21,000
25,200
100
1
22
145320
SD 40
1.8
35
40
19,200
24,000
28,800
150
1
24
145322
SD 60
2.3
40
60
28,800
36,000
43,200
250
1
28
145367
SD 70
3.15
50
70
33,600
42,000
50,400
300
1
58
145333
SD 80
3.5
50
75
36,000
45,000
54,000
350
1
76
145386*
SD80 2 in.
3.5
50
75
36,000
45,000
54,000
350
1
76
* with 2 in. valve
Dimensions and Performance
DIMENSION TABLE
Model
A DIM.
B DIM.
C DIM.
D DIM.
E DIM.
SD 35
33-1/2 in.
16-1/2 in.
37 in.
30-3/4 in.
34-1/4 in.
SD 40
37-3/4 in.
19-1/2 in.
46-1/4 in.
35 in.
43-1/2 in.
SD 60
43-3/4 in.
22-1/2 in.
52-1/2 in.
40-3/4 in.
49-1/4 in.
SD 70
46-1/4 in.
24 in.
57 in.
43-1/4 in.
53-3/4 in.
SD 80
48-3/4 in.
26 in.
65-3/4 in.
45-5/8 in.
62-1/2 in.
See page 385–386 for replacement parts.
67
FILTERS - SAND
TAGELUS® TOP MOUNT FILTER
FIBERGLASS TANK WITH MULTIPORT VALVE, CLAMP STYLE
Featured Highlights
• Special lateral design provides superior flow
characteristics and long filter cycles for economical
operation
• Maximum Operating Pressure 50 psi
• Combination water and sand drain makes servicing
and winterizing fast and easy
• 40, 50, and 60D models standard with plastic clamp
Our process creates a one-piece, fiberglass reinforced
tank with superior strength and durability. Tagelus®
filters are equipped with a six-position, clamp style, topmounted multiport valve.
Tagelus Top Mount
Filter
Ordering Information
Product
Model
Effective
Filtration Area
(Sq. Ft.)
Flow Rate
(GPM)
Turnover Capacity (In Gallons)
8 Hour
10 Hour
12 Hour
All Sand
Required
(Lbs.)
Carton
Qty.
Carton
Wt. (Lbs.)
TAGELUS FILTERS
144126
TA 40D
1.8
40
19,200
24,000
28,800
175
1
30
144127
TA 50D
2.3
50
24,000
30,000
36,000
225
1
35
145241
TA 60D
3.1
60
28,800
36,000
43,200
325
1
38
145240
TA 100D
4.9
100
48,000
60,000
72,000
600
1
78
145385*
TA60D(2)
3.1
60
28,800
36,000
43,200
325
1
38
Note: Operating Limits – maximum continual 0perating pressure of 50 PSI. Maximum operating water temperature (internal filter) 104°F (40°C).
* with 2 in. valve
Dimensions and Performance
68
See page 387–388 for replacement parts.
FILTERS - SAND
TRITON® II SIDE MOUNT FILTERS
FIBERGLASS SAND FILTER WITHOUT VALVES
Featured Highlights
•Heavy-duty closure provides easy inspection, and features an easy-toread pressure gauge with air relief valve
•Swing-away diffuser allows instant access to sand and all internal parts
•All internal parts are threaded for ease of service
•Internal air bleed
•Bulkhead connectors are threaded for easy installation and service
•Combination sand and water drain makes servicing and winterizing fast
and easy
•Maximum Operating Pressure 50 psi
Triton II Side Mount Filter
(Unions not included)
The original and still the industry standard. Our process creates a one-piece, fiberglass reinforced tank with
UV resistant surface finish for years of unequaled strength and durability. This method locks in fiberglass,
preventing fibers from “blooming” under harsh conditions.
Ordering Information
Product
Model
Effective
Filtration
Area
(Sq. Ft.)
Flow
Rate
(GPM)
Flow
Rate
(GPM
Comm)
Turnover Capacity (In Gal.)
8 Hour
10
Hour
12
Hour
Filter Media
Pea
Gravel
Req’d
(Lbs.)
All
Sand Sand Req’d
Req’d
(Lbs.)
(Lbs.)
Ctn
Qty.
Ctn Wt.
(Lbs.)
TRITON II SAND FILTERS
140236
TR 40
1.92
38
38
18,240
22,800
27,360
50
125
175
1
25
140249
TR 50
2.46
49
49
23,520
29,400
35,280
50
175
225
1
34
140264
TR 60
3.14
63
63
30,240
37,800
45,360
75
250
325
1
40
140210
TR 100
4.91
98
74
47,040
58,800
70,560
150
450
600
1
65
140243
TR 140
7.06
141
106
67,680
84,600
101,520
275
650
925
1
75
1
6
TRITON II VALVE OPTIONS
261173
1-1/2 in. MPV, for sand filters (SM 10-3)
1
263079
2 in. PVC Slide valve w/o plumbing, for D.E. & sand filters
1
3
261049
2 in. HiFlow valve, no plumbing
1
7
261050
2 in. HiFlow w/plumbing, for sand filters
1
11
261055
2 in. MPV, for sand filters (SM 20-3)
1
10
263064
Push Pull 7-1/2 in. Center Valve, Almond PVC
1
5
263080
Valve for Sand and Quad D.E., inlet port on top, Pentair 2 in. unions glued on
Valves must be purchased separately.
1
Note: Operating Limits – maximum continual operating pressure of 50 PSI. Maximum operating water temperature (internal filter) 104°F (40°C).
69
FILTERS - SAND
70
TRITON® II SIDE MOUNT FILTERS (CONT’D)
FIBERGLASS SAND FILTER WITHOUT VALVES
Dimensions and Performance
See pages 389–390 for replacement parts.
FILTERS - SAND
CRISTAL-FLO™ II TOP-MOUNT FILTERS
HIGH RATE SAND FILTERS
Featured Highlights
•Quality Construction – Durable one-piece extra-thick
molded poly­ethylene tank
•Safer – Internal air relief hole allows air to automatically
escape, preventing high pressure buildup
•6-Position Valve – Allows you to perform all necessary
water movement functions. A transparent sight-glass
adapter is included
•Large Drain Plug – Large drain plug is easy to get at for
removing and installing by hand or with tools if required
•Sleek Looks – Contemporary style with a textured black
finish that provides superior performance in all weather
conditions
Cristal-Flo II Top-Mount Filters
For residential inground or aboveground swimming pools requiring turnover through 59,000 gallons, at flow rates up
to 20 GPM for 8 to 10 hours. Permanent media high rate sand filters in 16 in., 19 in., 22 in., 24 in. and 26 in. diameter
models accommodate large and small pools, offering the best combination of economy, performance, ­durability and
ease of maintenance. Corrosion-resistant, one-piece, extra-thick molded polyethylene tank assures long service life.
Top-mounted, corrosion-resistant ­multiport selector valve included. Also includes a convenient tank winterizing drain
and continuous air relief system.
Ordering Information
Product
Effective
Filtration Area
(Sq. Ft.)
Max.
Pressure
(PSI)
Flow Rate
(GPM)
Turnover Capacity (In Gallons)
8 Hour
10 Hour
12 Hour
All Sand
Required
(Lbs.)
Carton Carton Wt.
Qty.
(Lbs.)
CRISTALFLO II FILTERS
145359
1.4
30
35
16,800
21,000
25,200
100
1
22
145360
1.8
35
40
19,200
24,000
28,800
150
1
24
145361
2.3
40
60
28,800
36,000
43,200
250
1
28
145362
3.15
50
70
33,600
42,000
50,4000
300
1
58
145363
3.5
50
75
36,000
45,000
54,000
350
1
76
145387
3.5
50
75
36,000
45,000
54,000
350
1
76
Dimensions and Performance
DIMENSION TABLE
Model
A DIM.
B DIM.
C DIM.
D DIM.
E DIM.
145359
33-1/2 in.
16-1/2 in.
37 in.
30-3/4 in.
34-1/4 in.
145360
37-3/4 in.
19-1/2 in.
46-1/4 in.
35 in.
43-1/2 in.
145361
43-3/4 in.
22-1/2 in.
52-1/2 in.
40-3/4 in.
49-1/4 in.
145362
46-1/4 in.
24 in.
57 in.
43-1/4 in.
53-3/4 in.
145363
48-3/4 in.
26 in.
65-3/4 in.
45-5/8 in.
62-1/2 in.
See page 391–392 for replacement parts.
71
FILTERS - SAND
SYSTEM 3® SAND FILTERS
SS SERIES FILTERS
Featured Highlights
•Typical Installations – Inground pools, inground hot tubs,
and water features
•Quality Construction – Durable two-piece tank housing
constructed of Dura-Glas™, Sta-Rite’s industry leading
glass-reinforced composite resin
•Innovative Design – The innovative design of the System
3 tank combined with the lateral/hub assembly produces a
balanced flow of water and deeper sand bed penetration
•Low Maintenance – The deep sand bed holds more dirt,
resulting in longer filter cycles and less cleaning
•Dual Drain Plugs – Side plug helps make sand removal easy,
while the bottom plug comes with integral screen for easy
draining without the loss of sand
System 3 Sand Filters
SS Series
•Sleek Looks – Contemporary style and matte black finish
looks attractive in any pool setting
System 3 brings you the proven p
­ erformance of Sta-Rite’s sophisticated sand filter hydraulics in the world’s easiestto-operate filter. Highly e
­ fficient, its s­ ophisticated design yields a uniform flow pattern through a deeper sand bed
than any other. Modular filter tanks allows for quick change of filter medias without changing the tank. Contemporary
style and matte black finish looks attractive in any pool setting.
Ordering Information
Product
Filter Area
(Sq. Ft.)
Flow Rated 1
at 15–20 GPM
(per Sq. Ft.)
Turnover Capacity (Gallons)
(Flow Rate x 60 x Hours)
6 Hour
8 Hour
10 Hour
Tank Port
Size
Sand 2
Required
(Lbs.)
Carton
Wt. (Lbs.)
SYSTEM 3 SAND FILTERS - SS SERIES
S7S50
2.4
36–48
13–17,000
17–23,000
22–29,000
2 in.
200
103
S8S70
3.4
51–68
18–25,000
25–33,000
31–41,000
2 in.
300
121
SS SERIES VALVE OPTIONS
3
18202-0150 ABS 6-Position Valve with Union Connections – 1-1/2 in. Valve Port
5
18201-0200 ABS 6-Position Valve with Union Connections – 2 in. Valve Port
8
263053
VLV Push Pull, 7.81 in. center
262508
FullFloXF for System 3 D.E. and Sand, inlet on bottom, with Sta-Rite offset adapters glued on
ACCESSORIES FOR SS SERIES
25021-2021 Sand Conversion Kit – S7S50 - Collector Assembly and Valve Sold Separately
5
25021-2025 Sand Conversion Kit – S8S70 - Collector Assembly and Valve Sold Separately
6
Based on NSF recommended flow rate for commercial at 15–20 GPM
per square foot.
1
Use only #20 white quartz silica sand, size range 0.40–0.55 mm; 12 in.
to 15 in. sand bed depth required.
2
72
Valves must be purchased separately.
3
Note: Operating Limits – maximum continual operating pressure of
50 PSI. Pool/Spa (bather) applications, maximum water temperature
(internal filter) 104°F (40°C).
Dimensions and Performance
18202-0150
1-1/2 in. MULTIPORT VALVE
FILTERS - SAND
SYSTEM 3® SAND FILTERS (CONT’D)
SS SERIES FILTERS
18201-0200
2 in. MULTIPORT VALVE
DIMENSION
Catalog Number
A
B
C
D
E
S7S50
28-1/242 7 3650
S8S70
32-1/242-1/4 8
40 50
A=width
B = height
C = number of clamps
D = area (width) needed to take off clamps
All dimensions shown in inches.
E = area (height) needed to remove top half of tank
All dimensions shown in inches.
See page 393 for replacement parts.
73
FILTERS - COMMERCIAL
THS SERIES® HORIZONTAL SAND FILTER
Featured Highlights
•Five sizes to 27 sq. ft.
•Manway in front for easy access and smaller footprint
•Manway with viewport available as option
•6 in. flanged connections, 4 in. victaulic on the THS 3461
•Optional manual, semi-automatic, and automatic backwash
systems for one and two tank systems
•Two backwash controllers to choose from
•Influent manifold distribution to prevent clogging
•NSF approved from 5–20 gpm/sq. ft.
THS Horizontal Sand Filter
The THS Filter is an NSF-approved 50 psi rated tank with flow rates up to 535 gallons per minute. The filter shell is
manufactured from a lasting composite laminate design that makes winding unnecessary. Paracote®, a waterbased,
environmentally-friendly coating, provides remarkable surface protection.
Ordering Information
Product
Model
Description
Effective
Filtration
Area
(Sq. Ft.)
Flow Rate
(15 GPM/
Sq. Ft.)
6 Hour Turnover
Capacity
(In Gallons)
Filter Media
Pea Gravel
Required
(Lbs.)
Sand
Required
(Lbs.)
All Sand
Carton Wt.
Required
(Lbs.)
(Lbs.)
THS HORIZONTAL FILTER
143461
THS3461
THS 34 in. x 61 in.
13.5
203
73,080
300
1250
1550
550
143484
THS3484
THS 34 in. x 84 in.
19.0
285
102,600
600
1350
1950
610
144272
THS4272
THS 42 in. x 72 in.
19.7
295
106,200
500
2100
2600
650
144284
THS4284
THS 42 in. x 84 in.
23.2
348
125,280
600
2400
3000
725
144296
THS4296
THS 42 in. x 96 in.
26.7
400
144,000
700
2800
3500
800
156400
Single THS manual controller 6 in. FP
CS400-01
CS400 backwash controller for single tank system
156450
Dual THS manual controller 6 in. FP
CS400-02
CS400 backwash controller for dual tank system
156800
Dual THS CA100 autobackwash controller
156850
Single THS CA100 autobackwash controller
CONTROLLERS (MUST USE WITH DIAPHRAGM VALVES MANIFOLD KITS)
CM200 Manual Backwash Controller
This is the simplest option. No electronics or programming required. Simply turn the knob to
backwash each tank in the system.
CS 400 Commercial Backwash Controller
This controller is programmable and controls every aspect of the backwash cycle once
initiated. Backwash can be initiated three ways: by an operator with the touch of a button,
by a signal from a master controller (such as the AK600), or by a signal from an optional
differential pressure switch (CS400-DP). Stored backwash data and history, alarms, and
calculated backwash cycle times are also features of the CS400 controller, as are relays for
communication with the heater, pump and Acu-drive.
CA 100 Fully Automatic Backwash Controller
74
This is the most comprehensive backwash controller and can be readily reprogrammed
to initiate backwash automatically based on differential pressure (integral pressure
transducers are standard), time (internal seven-day clock with battery back-up is standard),
flow (with optional flow sensor), or any combination of the above. The controller has real-time
display of operation mode, filter flow rate, and water temperature (with optional temperature
probe). Also, includes Energy Saver Mode for simple On/Off pump scheduling and various
interlocks and relays to communicate with other equipment (pump, heater, Acu-drive).
MANIFOLD KITS AND ACCESSORIES
140325
Adder kit for third THS Filter
156100
Temperature probe kit 4
2
155721
THS dual 34 x 84 in. 6 in. FP kit with diaphragm valves
155723
Kit-THS3461, dual tank manifold, with diaphragm valve kit
156150
Flowmeter saddle kit 6 in.
155730
THS dual 42 in. dia. 6 in FP Kit with diaphragm valves
155700
THS single tank manifold kit with butterfly valves 3
155800
WA-KIT wedge anchor *
kit 1
155702
Kit-THS3461, single tank manifold, with butterfly valve kit 3
155850
BVA-KIT 1/2 in. ball valve adapter kit for manual air relief 1
155720
THS dual tank manifold kit with butterfly valves 3
155705
Manway with Viewport upgrade - at time of purchase
155722
Kit-THS3461, dual tank manifold, with butterfly valve kit
155706
Manway with Viewport Retrofit Kit - replace existing in field
155701
THS single tank 6 in. FP kit with diaphragm valves
155703
Kit-THS3461, single tank manifold, with diaphragm valve kit
4
3
CS400DP
B4110
One each per tank purchased if required.
3
Adder Kit provides 6 in., SCH 80 manifold piping, fittings and hardware
for the addition of a third THS filter of equal diameter only when
#155720 Dual-Filter Butterfly Valve Face Piping Kit is used. Note:
Using a 6 in. Schedule 80 plumbing kit with flows in excess of 812 GPM
exceeds the maximum water velocity recommended in ANSI/NSPI-1
2003 Standard for Public Swimming Pools. For higher flows, summary
calculations should be provided to show that the greater flow is
possible with the pump and piping provided.
4
1
2
FILTERS - COMMERCIAL
THS SERIES® HORIZONTAL SAND FILTER (CONT’D)
Mounted differential pressure switch 5
120v to 24v 100w transformer
Does not require a purchase of a controller.
Only used with CA100 controller option.
Only available with CS400 controller.
5
Dimensions and Performance
THS SERIES SPECIFICATION CHART
Tank Dimensions
Model
“A”
in.
THS3461
39-1/2
THS3484
45
THS4272
“B”
in.
“C”
in.
“D”
in.
“E”
in.
“O.D.”
in.
WT
21
16
30
550
62
35
21-1/4 24-5/8 35-1/4
85
35
610
52-1/4 23-1/4 18-7/8 35-1/4
73
43
650
THS4284
52-1/4 23-1/4 24-7/8 35-1/4
85
43
725
THS4296
52-1/4 23-1/4 30-7/8 35-1/4
97
43
800
NSF-approved for 5–20 gpm/sq. ft.
* 4 in. victaulic on THS3461
See page 398 for replacement parts.
75
FILTERS - COMMERCIAL
TRITON® HD SIDE MOUNT FILTERS
HEAVY-DUTY FIBERGLASS SAND FILTER WITHOUT VALVES
Featured Highlights
Maximum Operating Pressure 75 psi
Triton HD Filter
(Unions not included)
All the same great performance and features of the original Triton® with maximum operating pressure of 75
psi for those special high pressure installations such as single pump in-floor cleaning systems.
Ordering Information
Product
Model
Effective
Filtration
Area
(Sq. Ft.)
140335
TR100 HD
4.91
Flow Rate
(GPM Res)
Flow Rate
(GPM Comm)
98
74
Turnover Capacity
(In Gallons)
8
Hour
10
Hour
Filter Media
12
Hour
Pea Gravel
Required
(Lbs.)
Sand
Required
(Lbs.)
70,560
150
450
All
Sand
Carton
Req’d Wt. (Lbs.)
(Lbs.)
TRITON HD SAND FILTER
47,040
58,800
TRITON HD VALVE OPTIONS
66
263079
2 in. PVC slide valve w/o plumbing, for D.E. & sand filters
3
261049
2 in. HiFlow valve, no plumbing
7
261050
2 in. HiFlow valve w/plumbing, for sand filters
11
261055
2 in. MVP, for sand filters (SM 20-3)
10
261173
1-1/2 in. MVP, for sand filters (SM 10-3)
6
263034
Push Pull 7-1/2 in. Center Valve, Almond PVC
5
263080
FullFloXF Valve for Sand and Quad D.E., inlet port on top, Pentair 2 in. unions glued on
Valves must be purchased separately.
1
Dimensions and Performance
76
600
1
See pages 389-390 for replacement parts.
FILTERS - COMMERCIAL
TRITON® C AND TRITON C-3
HIGH CAPACITY FIBERGLASS SIDE MOUNT SAND FILTER WITHOUT VALVES
Featured Highlights
•Maximum Operating Pressure 50 psi
•Full 2 in. Drain
•8 in. opening for easy access to sand bed
•The Triton C-3 features standard 3 in.
flange connections
•TR 100C-3 & TR 140C-3 models are
available in black only
This filter series features multiple diverters
for increased filtration rates in commercial
applications up to 20 GPM/sq. ft.
TR 100 C
TR 140C-3
Ordering Information
Product
Model
Effective
Filtration
Area
(Sq. Ft.)
Flow
Rate (GPM
Res) 2
Flow Rate
(GPM
Comm) 3
Turnover Capacity (In Gal.) 4
6 Hour
8 Hour
10 Hour
Filter Media
All
Sand
Pea Gravel
Sand Req’d Req’d
Req’d
(Lbs.)
(Lbs.)
(Lbs.)
Ctn
Qty.
Ctn
Wt.
(Lbs.)
TRITON C SAND FILTERS
140315
TR 100CAlmond
4.91
98
74
26,640
35,520
44,400
150
450
600
1
70
140316
TR 140CAlmond
7.06
141
106
38,160
50,880
63,600
275
650
925
1
82
TRITON C-3 SAND FILTERS
140310
TR 100C-3Black only
4.91
98
74
26,640
35,520
44,400
150
450
600
1
65
140342
TR 140C-3Black only
7.06
141
106
38,160
50,880
63,600
275
650
925
1
82
TRITON C VALVE OPTIONS 1
261050
2 in. HiFlow w/plumbing, for sand filters
1
11
261055
2 in. MPV, for sand filters (SM 20-3)
1
10
263010
Full-Flow valve, sand filters (will only work on the TR100C and TR140C models)
1
7
263080
FullFloXF Valve for Sand and Quad D.E., inlet port on top, Pentair 2 in. unions glued on
Valves must be purchased separately.
3
Based on 20 gpm per sq. ft.
4
1
2
Based on 15 gpm per sq. ft.
Based on 15 gpm per sq. ft.
Dimensions and Performance
See pages 395-396 for replacement parts.
77
FILTERS - COMMERCIAL
SCH 40 & 80 FOR TR100C, TR140C, TR100C-3 & TR140C-3
TANDEM FILTER PIPING KITS FOR 2 & 3 IN. FILTERS
These Tandem Filter Piping Kits are designed
specifically for use with the Triton TR100C,
TR140C, Triton TR100C-3 and TR140C-3 sand
filters to make the best even better.
We are providing this additional service for
your convenient one-stop shopping. Pipe and
filters are all you need.
Tandem Filter Piping Kits for Triton TR100C, TR140C,
TR100C-3 and TR140C-3 Sand Filters
Ordering Information
Product
Model
Product
For Plumbing Two TR100C or TR140C Filters
Model
Adder Kits for TR100C and TR140C Filters 1
146400
3 in. Two filter kit, SCH 40 (200 GPM)
146406
4 in. Single filter kit, SCH 40
146402
4 in. Two filter kit, SCH 40 (300 GPM)
146408
6 in. Single filter kit, SCH 40
146404
6 in. Two filter kit, SCH 40 (700 GPM)
146407
4 in. Single filter kit, SCH 80
146403
4 in. Two filter kit, SCH 80 (300 GPM)
146409
6 in. Single filter kit, SCH 80
146405
6 in. Two filter kit, SCH 80 (700 GPM)
Adder Kits for TR100C-3 and TR140C-3 Filters
For Plumbing Two TR100C-3 or TR140C-3 Filters
147400
3 in. Two filter kit, SCH 40 (200 GPM)
147406
4 in. Single filter kit, SCH 40
147408
6 in. Single filter kit, SCH 40
147402
4 in. Two filter kit, SCH 40 (300 GPM)
147407
4 in. Single filter kit, SCH 80
147404
6 in. Two filter kit, SCH 40 (700 GPM)
147409
6 in. Single filter kit, SCH 80
147401
3 in. Two filter kit, SCH 80 (200 GPM)
147403
4 in. Two filter kit, SCH 80 (300 GPM)
147405
6 in. Two filter kit, SCH 80 (700 GPM)
Note: All kits include hardware, fittings, gaskets.
Note: All kits include hardware, fittings, gaskets and butterfly valves.
Filters
Filter Area
Sq. Ft.
Manifold
Pipe Dia.
Filter Rate Sq. Ft.
15 GPM
20 GPM
Turnover Capacity
6 Hours
8 Hours
10 Hours
TANDEM TRITON 140C FILTER INSTALLATION
78
6 TR 140’s
42.36
7 TR 140’s
49.42
8 TR 140’s
56.48
6 in.
635
—
228,600
304,800
381,000
8 in.
—
847
304,920
406,560
508,200
6 in.
741
—
266,760
355,680
444,600
8 in.
—
988
355,680
474,240
592,800
8 in.
847
—
304,920
406,560
508,200
8 in.
—
1130
406,800
542,400
678,000
TANDEM FILTER PIPING KITS FOR 2 & 3 IN. FILTERS
Filters
Filter Area
Sq. Ft.
Filter Rate Sq. Ft.
Manifold
Pipe Dia.
15 GPM
Turnover Capacity
20 GPM
6 Hours
8 Hours
10 Hours
TANDEM TRITON TR100C AND TR100C-3 FILTER INSTALLATION
2 TR 100’s
9.82
3 TR 100’s
14.73
4 TR 100’s
19.64
5 TR 100’s
24.55
3 in.
147
—
52,920
70,560
88,200
4 in.
—
196
70,560
94,080
117,600
4 in.
221
—
79,560
106,080
132,600
4 in.
—
295
106,200
141,600
177,000
4 in.
295
—
106,200
141,600
177,000
5 in.
—
393
141,480
188,640
235,800
5 in.
368
—
132,480
176,640
220,800
5 in.
—
491
176,760
235,680
294,600
FILTERS - COMMERCIAL
SCH 40 & 80 FOR TR100C, TR140C, TR100C-3
& TR140C-3 (CONT’D)
TANDEM TRITON TR140C AND TR140C-3 FILTER INSTALLATION
2 TR 140’s
14.12
3 TR 140’s
21.18
4 TR 140’s
28.24
5 TR 140’s
35.30
4 in.
212
—
76,320
101,760
127,200
4 in.
—
282
101,520
135,360
169,200
4 in.
318
—
114,480
152,640
190,800
5 in.
—
424
152,640
203,520
254,400
5 in.
424
—
152,640
203,520
254,400
6 in.
—
565
203,040
270,720
338,400
5 in.
530
—
190,800
254,400
318,000
6 in.
—
706
254,160
338,880
423,600
Dimensions and Performance
Two Filter
System
A
B
C
D
E
F
G
H
I
J
K
Total Wt.
3 in.–TR100C
82-3/8 in. 17-15/16 in. 48 in. min.
18 in. min.
39-3/4 in.
15 in.
29-33/64 in.
8-5/8 in.
11-1/32 in. 51-13/16 in.
—
2300 lbs.
3 in.–TR140C
88-3/8 in. 17-15/16 in. 54 in. min.
18 in. min.
45-1/4 in.
18 in.
32-33/64 in.
8-5/8 in.
13-15/32 in. 57-13/16 in.
—
3200 lbs.
4 in.–TR140C
95-3/4 in. 19-35/64 in. 54 in. min.
18 in. min.
45-1/2 in.
18 in.
33-1/8 in.
9-15/16 in. 12-21/32 in. 59-11/64 in.
—
2300 lbs.
6 in.–TR140C * 111-3/4 in. 24-7/32 in. 54 in. min.
18 in. min.
45-1/2 in.
18 in.
35-3/8 in. 12-13/16 in. 10-21/64 in. 64-13/32 in. 64-53/64 in. 3550 lbs.
* 6 in. piping needs to be rotated upward as shown at 25° so handle will clear the floor.
FIGURE 4A
FIGURE 4B
See page 397 for replacement parts.
79
FILTERS - ACCESSORIES
PLUMBING KITS & ACCESSORIES
Featured Highlights
•Unionized pump/filter plumbing kits and base
•Bulkhead Union Sets can connect D.E. and high-rate
sand filters to any plumbing. The kit consists of two half
unions with both 1-1/2 and 2 in. pipe connections.
50901600
154566
Ordering Information
Product
Description
Carton Qty.
Carton Wt. (Lbs.)
1
0.5
1
0.5
1
1
1
1
UNIONS
98960311
Bulkhead union kit, 1-1/2 in. & 2 in. for Eclipse Filters
SIGHT GLASS
50901600
Sight glass, 1-1/2 in. socket
TOOLS
010126
Filter lid opener
192019
Drain plug wrench
1
1
ACCESSORIES AND KITS
154566
2 in. Sight glass nipple, clear
1
1
185208
Plumbing kit, NS/FNS/CH, for use with Slide valve & Challenger, without
valve
1
18
271092
2 in. Threaded adapter kit, for installations without valve
1
3
271094
1-1/2 in. Threaded adapter kit, w/o valve, for installations without valve
1
3
271096
2 in. Threaded bulkhead adapter kit, for installations without valve
1
3
274725
Union check valve, 2 in. socket
1
2
354570
1-1/2 in. Quick disconnect kit, for Regenerative D.E. Filter
1
2
542090
Sand Vac, empties a sand filter in 10 minutes for repair, refilling, or removal
1
3
For use on FNS Plus, Nautilus Plus & Clean & Clear Plus filters.
1
For use on Star filters.
2
Torque wrench not required for filters with Tension Control™ clamp.
3
542090
80
354570
(now available in black)
274725
185208
See page 400 for replacement parts.
271094, 271096,
271092
Ordering Information
Product
Description
FNS KITS
181010
Product
Description
PF SAND KITS 1
1
181011
FNS clamp spring kit
(works on all FNS clamps after 1-89)
NS/PF35 spring clamp assembly
FILTER UPGRADES
NS KITS 1
98209804
High flow manual air relief valve
w/instruction labels
For filters manufactured prior to 1991.
98201300
Tension Control™ clamp for s/s filters 2
For use on filters built before 11-94.
59000400
High flow internal air relief kit upgrade for Titan
manifold
181011
NS/PF35 spring clamp assembly
1
2
FILTERS -ACCESSORIES
RETRO-FIT & UPGRADE KITS
FILTER BASE KITS
BASE KITS FOR D.E. AND/OR SAND FILTERS
180010 - Elevated Base, Pump to Valve
Plumbing Parts, and Mounting Hardware.
Use with FNS Plus Filters and Challenger
Pumps with Slide Valve.
Ordering Information
Product
Description
Carton
Qty.
Carton
Wt. (Lbs.)
1
18
ELEVATED BASE KITS
180010
Base kit FNS Plus/CH/Slide, used for mounting FNS Plus and Slide Valves with
Challenger Pump
81
82
FILTERS - SAND
NOTES:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising