Thermo-FILM

Thermo-FILM
APPLICATION INSTRUCTIONS FOR
To Order: StahlsID.com • 800.4.STAHLS • Fax: 800.346.2216
International: StahlsInternational.com • 586.772.5551
Canada: StahlsCanada.com • 800.521.5255
Thermo-FILM ®
FEED
MATERIAL—
into cutter
so that the
carrier is on
the bottom.
PREHEAT &
POSITION—
Preheat garment for 10
seconds, prior to application. Position weeded
design on garment with
the carrier side up (reads
left to right). Place cover
sheet over graphic.
Recommended Fabrics
Cotton
Polyester
Poly/cotton blends
Polyester knits
Polyester mesh
Sublimated Polyester
Poly/foam & cotton caps
Satin
Due to the combination of fabrics, weaves,
coatings and dyes used in the textile industry,
Stahls’ recommends and provides samples
of our materials and medias for testing.
CUT LOGO,
words or
numbers
in reverse
(mirror
image).
HEAT APPLY—
Temperature: 330°F; 165°C
Time: 6-8 seconds
Pressure: medium
#4 on Hotronix®
WEED away
excess material
leaving only
the desired
graphic on the
carrier.
PEEL WARM—
Tip: A Heat Printing Pillow or Print
Perfect Pad is recommended
for even pressure when working
around zippers, buttons,heavy
seams or mesh reversible jerseys.
Accessories Required
Kraft Paper or Reusable Cover Sheet
EZ Weeder® or Tweezers
Cutting Notes
You should always test cut prior to any production run. Remember cutter settings will
need to be adjusted as your blade ages.
For optimal cutting and weeding, maintain
a line thickness of at least 1/8” for lettering
& logos. For detailed designs or smaller
graphics, use CAD-CUT® Fashion-FILM™.
Care Instructions
Machine wash using mild detergent.
Do not use bleach. Dry at a normal dryer
setting on household machines.
Do not iron directly onto this material.
Thermo-FILM® can be dry cleaned.
Multi-Color Designs
Application on Sublimated Jerseys
Do NOT preheat the garment. Apply Thermo-FILM® at the lowest possible temperature
—300°F/149°C for 12-15 seconds—light pressure.
CUTTER GUIDELINES
Apply background for 2 seconds; Peel
HOT. Apply foreground for 2 seconds;
Peel HOT. Cover with Kraft Paper and
heat seal for 10 seconds at 330° F,
medium pressure.
Storage
CUTTER
BLADE
FORCE
OFFSET
SPEED
Roland GX-24
45° / 60°
120-160g / 140-170g
.25 / .50
50cm/s
Ioline 100
45°
275-300g
.15
12:30
Ioline 300
30°
180g
.15
12:15
Stahls’ Thermo-FILM® has an indefinite shelf
life when stored at temperatures below
80°F. Keep away from direct heat, sunlight
and humidity.
All technical information and recommendations are based on tests we believe to be reliable. However, we cannot guarantee performance for
conditions not under manufacturer's control. Before using, please determine the suitability of product for its intended use. The user assumes all
risk and liability whatsoever in connection with the use of this product. Seller's and man­ufacturer's only obligation shall be to replace such
quantity of the product proved to be defective by manufacturer.
CAD-CUT, Thermo-FILM, Fashion-FILM, & Hotronix are trademarks & ® trademarks of Stahls’ ID Direct™ with one or more patents or patents pending.
© Stahls’ ID Direct™ 2012 - All International Rights Reserved
06/12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising