Delta Temperature Controller DT Series

Delta Temperature Controller DT Series
Automation for a Changing World
Delta Temperature Controller
DT Series
www.delta.com.tw/ia
Features
Many Sizes Available:
■ From 48x24mm to 96x96mm, all panel sizes comply with international standards.
Quality Assurance:
■ All temperature controllers adopt an
isolated switching power supply.
■ 100 ~ 240VAC input power supply,
applicable in all countries of the world.
■ CE, UL and C-Tick certified
Supports Various Sensors:
■ Built-in various sensor input modes: Thermocouple,
platinum RTD or linear voltage/current.
+
A
+
-
B
B
Thermocouple
(TC)
Platinum RTD
(RTD)
-
Linear current
(mA)
+
V
-
Linear voltage
(V)
Various Output Modes:
■ Relay, voltage pulse, linear voltage, and linear current
NO
NC
COM
Relay
+
+
-
-
Voltage pulse
(For driving SSR)
Linear current
(mA)
V
+
-
Linear voltage
(V)
Stable Control:
■ Built-in PID control function, with accurate auto-tuning (AT).
■ PID parameters are automatically calculated, which enhances
the stability of the system and accuracy of control.
(Before AT)
PV
(After AT)
PV
Current Transformer (CT):
■ CT can enable the off-line alarm and can detect if the current
is overloaded.
1
Programmable Control:
■ Max. 8 patterns available, with 8 steps in each pattern.
No master controller is required for planning many kinds of
temperature control curves.
Ramp
100°
70°
50°
30°
5
Soak
3
8
5
3
3
Minute
Communication:
■ RS-485 communication interface, supporting Modbus
ASCII/RTU communication
PLC
HMI
Modbus RTU
Modbus ASCII
Safety:
■ The key-locking function and
communication protection
prevents malfunction.
Dual Output Control:
■ Able to execute heating and cooling
controls at the same time, allowing
the system to reach the
set temperature quickly.
Steam Heating
Sensor
Cooling Water
PID
2
Products
DT3
Next Generation Temperature
Controller
The Delta temperature controller DT3 series is designed with
upgraded hardware and higher specifications as well as smart
operation, fast response, easy modularization, plus user-friendly and
user-defined function keys. With Self-Tuning and FUZZY temperature
control functions, controllers can be installed in open space and
confined space applications and are capable of presenting a smooth
temperature control curve. In addition, the innovative design enables
customers to replace the module with new functions to attain the
ultimate in extension flexibility.
Remote Control
Sets DT3 temperature via analog output of host controller
Temperature
signal input
Hotplate
Analog signal mA/V
Remote control via analog
signal or communication
protocols
Control output
Various Control Modes
0~20mA, 4~20mA
0~5V, 0~10V
► Self Tuning
► FUZZY
► Auto - tuning
► ON/OFF
Self-tuning Control
► Manual
Fuzzy Control
Temperature
Temperature
Time
3
Time
Extension Ability
User-defined Function Keys
Modular design of functional devices lets
users replace the module as needed for
application flexibility
► Menu
► Auto - tuning
► Control modes selection
► RUN/STOP Mode
► Program hold
Point-to-Point Control
Large 3-color LCD Display
(Proportional Output mA/V)
The 1st 3-color LCD temperature
controller in Taiwan.
Sets the Present Value by point-to-point
control.
Dual Output Control
►Preset temperature is rapidly attained
using two sets of outputs for heating
and cooling control.
►This function is used to automatically
calculate two sets of PID parameters,
one for heating and one for cooling.
Heater Disconnection
Detection
Measurable up to 100A
Power
Output 1
(Heating Control)
Output 2
(Cooling Control)
Retransmission Output
Present Value Transmission mA/V
Current Transfer
Inject
4
Specifications
Input power supply
AC 80 to 260 V, 50/60Hz, DC 24 V ±10%
Display method
LCD. Present temperature: red, Set temperature: green
Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK
Input sensors
Platinum RTD: Pt100, JPt100
Analog input: 0 to 5 V, 0 to 10 V, 0 to 20 mA, 4 to 20 mA, 0 to 50 mV
Control modes
PID, PID programmable, Fuzzy, Self-tuning, manual, ON/OFF
Display accuracy
0 or 1 digit to the right of the decimal point
Sampling rate
Analog input: 0.1s, Thermocouple or platinum RTD: 0.1s
Ambient temperature
0 ~ +50℃
Ambient humidity
35 to 80% RH (non-condensing)
Alarm Outputs
The DT3 offers 3 alarm outputs, and each alarm output has 12 alarm modes to choose from in the initial setting mode.
When the target temperature exceeds or falls below the set point, the alarm output is enabled.
SV
Alarm mode
Alarm output operation
0
No alarm
1
Alarm output will be enabled when the temperature reaches upper or lower limit:
The alarm will be enabled when the PV exceeds SV + AL-H or falls below SV AL-L.
2
Alarm output will be enabled when the temperature reaches the upper limit:
The alarm will be enabled when the PV exceeds SV + AL-H.
3
Alarm output will be enabled when the temperature reaches the lower limit:
The alarm will be enabled when the PV falls below SV AL-L.
4
Alarm output will be enabled when the temperature reaches the absolute value of the
upper or lower limit: The alarm will be enabled when the PV exceeds AL-H or falls below
AL-L.
5
Alarm output will be enabled when the temperature reaches the absolute
value of the upper limit: The alarm will be enabled when the PV exceeds AL-H.
6
Alarm output will be enabled when the temperature reaches the absolute value of
the lower limit: The alarm will be enabled when the PV falls below AL-L.
7
Upper limit hysteresis alarm: The alarm will be enabled when the PV exceeds
SV + AL-H. The alarm will be disabled when the PV falls below SV + AL-L.
8
Lower limit hysteresis alarm: The alarm will be enabled when the PV below SV AL-H. The
alarm will be disabled when the PV exceeds SV AL-L.
9
Offline alarm: The alarm will be enabled when the input sensor is not correct or offline.
10
Timing alarm
11
Ct1 alarm: The alarm will be enabled when the CT1 value falls below AL-L or exceeds AL-H.
12
Ct2 alarm: The alarm will be enabled when the CT2 value falls below AL-L or exceeds AL-H.
5
ON
OFF
SV-(AL-L)
SV
SV-(AL-H)
SV
SV-(AL-H)
ON
OFF
ON
OFF
SV-(AL-L)
SV
ON
OFF
AL-L
AL-H
ON
OFF
AL-H
ON
OFF
AL-L
ON
OFF
AL-L
AL-H
ON
OFF
AL-L
AL-H
ON
OFF
AL-L
AL-H
RS-485 Communication
DT3 supports baudrate 2,400 to 38,400 bps, MODBUS ASCII/RTU protocol, function code 03H and reads maximum 8
words from the register.
Address
Content
Definition
1000H
Present value (PV)
Measuring unit: 0.1 scale. The following values read mean error occurs.
8002H: Temperature not yet acquired
8003H: Not connected to sensor
8004H: Incorrect sensor
1001H
Set value (SV)
Measuring unit: 0.1 scale.
1002H
Upper limit of temp. range
Cannot exceed the default value
1003H
Lower limit of temp. range
Cannot fall below the default value
1005H
Control mode
0: PID, 1: ON/OFF, 2: Manual, 3: PID programmable
1006H
Heating/cooling control
0: Heating, 1: Cooling, 2: Heating/cooling, 3: Cooling/heating
1007H
st
0 ~ 99 sec. 0: 0.5 sec.
nd
1 heating/cooling control cycle
1008H
2 heating/cooling control cycle
0 ~ 99 sec. 0: 0.5 sec.
1009H
Proportional band (PB)
0.1 ~ 999.9
100AH
Ti value
0 ~ 9999
100BH
Td value
0 ~ 9999
1012H
Read/write Output 1 volume
Unit: 0.1%, only valid in manual control mode
1013H
Read/write Output 2 volume
Unit: 0.1%, only valid in manual control mode
1016H
Regulated temp. value
-99.9 ~ +99.9, Unit: 0.1
102AH
Read/write LED status
b0:ALM3,b1:ALM2,b2:F,b3:C,b4:ALM1,b5:
OUT2,b6:OUT1,b7:AT
102BH
Read/write key status
b0: Set, b1: Select, b2: Up, b3: Down, 0: Press it
102CH
Panel lockup status
0: Normal, 1: Fully locked, 11: SV adjustable
102DH
CT value
Unit: 0.1A
1815H
Programmable control Run or
Stop
0: Run (default), 1: Stop
1816H
Programmable control Run or
Pause
0: Run (default), 1: Pause
6
Parameters Operation
Regulation
Mode
Press SET for less than 3 sec.
Operation
Mode
Press SET for less than 3 sec.
Press SET
Press SET
Regulation Mode
Auto-tuning (Set in PID
control and RUN mode)
Press
Operation Mode
Use
to set up
target temperature
Press
Self-tuning switch (set when
in PID control and the TUNE
parameter = ST)
Select the nth (n = 0 ~ 5)
PID. When n = 6, PID is autoselected.
Set up PID control offset
Set up Fuzzy gain value
Set up Fuzzy Deadband
Control loop RUN or STOP
Initial Setting
Mode
Initial Setting Mode
Set up input type
Press
Set up temperature unit (not
displayed when in analog input)
Set up start pattern (when in
PID programmable control
and
)
Set up upper temperature limit
Set up start step (when in
programmable control)
Set up upper temperature limit
point
Set up the position of decimal
Select control modes
Lock the keys
Select SV control modes
Adjust Output 1 hysteresis
(when in ON/OFF control)
Set up upper limit of Alarm 1
Set up waiting temperature
(when in programmable control)
Adjust Output 2 hysteresis
(when in ON/OFF control)
Set up lower limit of Alarm 1
Set up waiting time (when in
programmable control)
Control cycle for
Output 1 (except in ON/OFF control)
Set up upper limit of Alarm 2
Set up start slope (when in
programmable control)
Control cycle for
Output 2 (except in ON/OFF control)
Set up lower limit of Alarm 3
Select pattern to be edited
Ratio of Output 1 against
Output 2 when in dual output control
(set when in PID and dual output
control)
Set up upper limit of Alarm 2
Select AT or ST
Set up deadband (when in
dual output)
Set up lower limit of Alarm 3
Select heating, cooling or dual
output heating and cooling
Set up input filter factor
Record highest temperature of
Alarm 1
Set up Alarm 1 mode
Set up input filter range
Record lowest temperature of
Alarm 1
Set up Alarm 1
options
Adjust input compensation
Record highest temperature of
Alarm 2
Set up Alarm 1 delay
Adjust input gain
Record lowest temperature of
Alarm 2
Set up reverse alarm output
Set up rising slope (when
CRTS = SLOP)
Record highest temperature of
Alarm 3
Set up Remote type
Adjust upper limit
compensation for analog Output 1*
Record lowest temperature of
Alarm 3
Select auxiliary function
7
Regulation Mode
Operation Mode
Initial Setting Mode
Enable/disable communication
write-in
Adjust lower limit
compensation for analog Output 1*
Display and adjust Output 1
volume
Adjust upper limit
compensation for analog Output 2*
Display and adjust Output 2
volume
Adjust lower limit
compensation for analog Output 2*
Set up upper limit
percentage for Output 1
Set up communication
address
Adjust upper limit
compensation for Retransmission*
Set up lower limit
percentage for Output 1
Set up baudrate
Adjust lower limit
compensation for Retransmission*
Set up upper limit
percentage for Output 2
Set up data length
Set up lower limit
percentage for Output 2
Set up stop bit
Adjust Remote gain
Adjust Remote compensation
Set up EVENT1 function
CT1
CT2
Set up EVENT2 function
Set up EVENT3 function
Press
to return to
auto-tuning
Select ASCII or RTU format
Display current measured at
Set up parity bit
Display current measured at
Press
to return to set up
target temperature
Press
to return to set
up input type
*1 scale = 1μA; 1scale = 1mV
PID mode: Any of the 6 PID groups can be selected. When n = 6, the program will automatically select the PID
group that is the closest to the target temperature.
Select the nth PID (n = 0 ~ 5)
Set up the 0th PID
temperature value Press
Set up the 5 th PID
temperature value Press
Set up the 0th proportional
band value
Set up the 5 th proportional
band value
Set up the 0th Ti value
Set up the 5 th Ti value
Set up the 0th Td value
Set up the 5 th Td value
Set up the 0th PID integral
deviation
Press
Press
0 ~ 5 th PID
Patterns and steps: Edit
in
Select the pattern number to
be edited
Select number
Press
to select OFF
Exit pattern and step editing and
switch to
to continue the
setup process
to return to PID
deviation
Set up the 5 th PID integral
deviation
Press
to return to PID
deviation
parameter. Take editing pattern 0 for example:
Edit temperature for Step 0
Press
Edit time for Step 0
(time unit: hr, min)
Set up Step 0 ~ 15 in order
Edit temperature for Step 15
Edit time for Step 15
Press
to set up actual
step numbers
8
Select actual number of
steps when the program is executing
Press
Set up additional cycles
(0 ~ 99) for the pattern execution
Set up link pattern. OFF refers
to the program end.
Press
to return to select the
pattern number to be
edited
Products
Standard Type
DTA is designed for practical applications, offering the 3 most
frequently adopted output types in the market. DTA has many
user-friendly functions built-in and a handy transmission structure,
ensuring fast and stable data transmission.
Optional functions: RS-485 communication interface
(MODBUS ASCII/RTU, 2,400 ~ 38,400bps),
CT (current transformer)
Electrical Specifications
Power supply
100 ~ 240VAC, 50/60Hz
Voltage range
85 ~ 110% rated voltage
Power consumption
5VA Max.
Display
2-line 7-segment LED display, PV: red; SV: green
Input temperature
sensors
Thermocouple: K, J, T, E, N, R, S, B, U, L, TXK
Display scale
0.1% full scale
Control methods
PID, ON/OFF, Manual
Platinum RTD: Pt100, JPt100
Relay: 250VAC, 5A, SPDT (DTA4848: SPST)
Output types
Voltage pulse: 14VDC, Max. output current: 40mA
Current: DC 4 ~ 20mA (Load resistance: < 600W)
Sampling rate
0.5 second
Communication
RS-485 digital communication, 2,400 ~ 38,400bps (optional)
Communication
protocol
MODBUS protocol, ASCII/RTU format (optional)
Vibration resistance
10 ~ 55Hz, 10m/s² for 10 mins in X, Y, Z direction
Shock resistance
Max. 300m/s² , 3 times in each of 3 axes, 6 directions Ambient temperature
0℃~ 50℃
Storage temperature
- 20℃~+ 65℃
Altitude
< 2,000m
Ambient humidity
35 ~ 85% RH (non-condensing)
Waterproof degree
IP56
9
Advanced Type
Compared to the DTA, DTB has an added linear voltage output and adopts dual-loop output control, able to execute
heating and cooling controls at the same time in a temperature control system.
DTB series has a built-in RS-485 communication interface (MODBUS ASCII/RTU, 2,400 ~ 38,400bps). The
programmable PID control function allows the DTB to set up 64 sets of temperature and control times.
Optional functions:
■ CT (current transformer), output by alarm.
■ EVENT function, switching between
2 SVs by using PLC or switches.
■ Valve models are able to adjust
the openness of valves
depending on the SV.
Electrical Specifications
Power supply
100 ~ 240VAC, 50/60Hz
Voltage range
85 ~ 110% rated voltage
Power consumption
< 5VA
Display
2-line 7-segment LED display, 4 digits available, PV: red, SV: green
Input temperature
sensors
Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK
Platinum RTD: Pt100, JPt100
Analog input: 0 ~ 5V, 0 ~ 10V, 0 ~ 20mA, 4 ~ 20mA, 0 ~ 50mV
Display scale
1 digit after decimal point, or no decimal point
Control methods
PID, programmable PID, ON/OFF, Manual
Relay: SPDT (DTB4848/4824: SPST), Max. load: 250VAC, Resistive load: 5A
Output types
Voltage pulse: 14VDC, Max. output current: 40mA
Current: DC 4 ~ 20mA (Load resistance: < 600WΩ)
Analog voltage: 0 ~ 10V
Sampling rate
Analog input: 0.15 second, Thermocouple or platinum RTD: 0.4 second
Communication
RS-485 digital communication, 2,400 ~ 38,400bps
Communication
protocol
MODBUS protocol, ASCII/RTU format
Vibration resistance
10 ~ 55Hz, 10m/s² for 10 mins in X, Y, Z direction
Shock resistance
Max. 300m/s², 3 times in each of 3 axes, 6 directions
Ambient temperature
0℃~ 50℃
Storage temperature
- 20℃~+ 65℃
Altitude
< 2,000m
Ambient humidity
35 ~ 85% RH (non-condensing)
Waterproof degree
IP56
10
Products
Modular Type
DTC features a modular and wire-saving structure, and is able to monitor
many temperature points by parallel and modular extension. The user is
able to set up the suitable output method according to actual demand. The
built-in password protection prevents unauthorized operation or malicious
damage from staff.
DTC series has a built-in RS-485 communication interface (MODBUS ASCII/
RTU, 2,400 ~ 38,400bps). The programmable PID control function allows the
DTC to set up 64 sets of temperature and control times. DTC also supports
3 levels of password protection, synchronous communication protocol and
auto ID setup.
Electrical Specifications
Power supply
24VDC, isolated switching power supply
Voltage range
90 ~ 110% rated voltage
Power consumption
3W + 3W x number of DTC2000 controllers connected in parallel (Max. 7)
Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK
Input temperature
sensors
Platinum RTD: Pt100, JPt100
Control methods
PID, programmable PID, ON/OFF, Manual
Linear current: 0 ~ 5V, 0 ~ 10V, 0 ~ 20mA, 4 ~ 20mA, 0 ~ 50mV
Relay: SPST, Max. load: 250VAC, Resistive load: 3A
Output types
Voltage pulse: 12VDC, Max. output current: 40mA
Current: DC 4 ~ 20mA (Load resistance: < 500WΩ)
Analog voltage: 0 ~ 10V (Load resistance: > 1,000WΩ)
Sampling rate
Analog input: 0.15 second, Thermocouple or platinum RTD: 0.4 second
Communication
RS-485 digital communication, 2,400 ~ 38,400bps
Communication
protocol
MODBUS protocol, ASCII/RTU format
Vibration resistance
10 ~ 55Hz, 10m/s2 for 10 mins in X, Y, Z direction
Shock resistance
Max. 300m/s², 3 times in each of 3 axes, 6 directions
Ambient temperature
0℃~ 50℃
Storage temperature
- 20℃~+ 65℃
Altitude
< 2,000m
Ambient humidity
35 ~ 85% RH (non-condensing)
11
Economical Type
DTD series offers PID, programmable PID, ON/OFF and Manual
control modes and supports 1 alarm output with 8 alarm modes,
which reduces cost but enhances functions.
The programmable PID control function allows the DTD to set up
8 sets of temperature and control times.
Electrical Specifications
Power supply
100 ~ 240VAC, 50/60Hz
Voltage range
85 ~ 110% rated voltage
Power consumption
6VA Max.
Display
7-segment LED display, PV: red, SV: green
Input temperature
sensors
Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK
Platinum RTD: Pt100, JPt100
Copper resistance: Cu50
Current: 0 ~ 20mA, 4 ~ 20mA
Voltage: 0 ~ 5V, 0 ~ 10V, 0 ~ 70mV
Display scale
K2, J2, T2, Pt100-2, JPt100, Cu50: 0.1°, Others: 1°
Control methods
PID, programmable PID, ON/OFF, Manual
Output types
Relay: 250VAC, 5A, SPST
Voltage pulse: 14VDC, Max. output current: 40mA
Sampling rate
0.4 second (analog input and sensor input)
Vibration resistance
10 ~ 55Hz, 10m/s2 for 10 mins in X, Y, Z direction
Shock resistance
Max. 300m/s², 3 times in each of 3 axes, 6 directions
Ambient temperature
0℃~ 50℃
Storage temperature
- 20℃~+ 65℃
Altitude
< 2,000m
Ambient humidity
35 ~ 85% RH (non-condensing)
Waterproof degree
IP56
12
Products
Multi-Channel Modular Type
DTE series is a multi-channel modular type temperature controller.
The DTE10T supports 8 thermocouple inputs and the DTE10P
supports 6 platinum RTD inputs. The DTE series is installed on
DIN rail, and each channel operates independently. DTE series
offers many optional output modules (relay, voltage pulse, current
and linear current). The built-in RS-485 2-wire communication
allows transmission of up to 115,200bps.
The programmable PID control function allows the DTE to set up
64 sets of temperature and control times. Maximum 7 DTC2000
controllers are extendable to DTE, and DTE supports the same
synchronous communication protocol and auto ID setup which
DTC supports.
Electrical Specifications
Power supply
24VDC, isolated switching power supply
Voltage range
90 ~ 110% rated voltage
Power consumption
Max. 10W + 3W + 3W x number of DTC2000 controllers connected in
parallel (Max. 7)
Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK
Input temperature
sensors
Platinum RTD: Pt100, JPt100
Control methods
PID, programmable PID, ON/OFF, Manual
Copper resistance: Cu50
Relay: SPST, Max. load: 250VAC, Resistive load: 3A
Output types
Voltage pulse: 24VDC, Max. output current: 40mA
Current: DC 4~20mA (Load resistance: < 500WΩ)
Analog voltage: 0 ~ 10V (Load resistance: > 1,000Ω)
Sampling rate
Thermocouple or platinum RTD: 1.0 second/all inputs
Communication
RS-485 digital communication, 2,400 ~ 115,200bps
Communication
protocol
MODBUS protocol, ASCII/RTU format
Vibration resistance
10 ~ 55Hz, 10m/s² for 10 mins in X, Y, Z direction
Shock resistance
Max. 300m/s², 3 times in each of 3 axes, 6 directions
Ambient temperature
0℃~ 50℃
Storage temperature
- 20℃~+ 65℃
Altitude
< 2,000m
Ambient humidity
35 ~ 85% RH (non-condensing)
13
Valve Type
DTV series is designed for electronic valve applications. It is user-friendly and easy to use.
DTV has built-in MODBUS communication, which allows handier data collection.
DTV also features:
■ Auto/manual mode switching by a single key.
■ "Left" key makes the parameter setting faster.
■ Real-time output percentage display,
for the user to check the openness of the valve.
■ 2 alarm outputs, 17 alarm modes.
■ RS-485 communication interface for DTV
to monitor and collect data from other
temperature controllers on the network.
Electrical Specifications
Power supply
100 ~ 240VAC, 50/60Hz
Voltage range
85 ~ 110% rated voltage
Power consumption
< 5VA
Display
2-line 7-segment LED display, 4-bit or 2-bit valve openness display available
PV: red, SV & openness of valve: green
Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK
Input temperature
sensors
Platinum RTD: Pt100, JPt100
Display scale
1 digit after decimal point, or no decimal point
Control methods
PID, programmable PID, ON/OFF, Manual
Output types
Analog input: 0 ~ 5V, 0 ~ 10V, 0 ~ 20mA, 4 ~ 20mA, 0 ~ 50mA
Relay: SPST
Max. load: 250VAC, Resistive load: 5A
Sampling rate
Analog input: 0.15 second, Thermocouple or platinum RTD: 0.4 second
Communication
RS-485 digital communication, 2,400 ~ 38,400bps
Communication protocol
MODBUS protocol, ASCII/RTU format
Vibration resistance
10 ~ 55Hz, 10m/s² for 10 mins in X, Y, Z direction
Shock resistance
Max. 300m/s², 3 times in each of 3 axes, 6 directions
Ambient temperature
0℃~ 50℃
Storage temperature
- 20℃~+ 65℃
Altitude
< 2,000m
Ambient humidity
35 ~ 85% RH (non-condensing)
Waterproof degree
IP56
14
Ordering Information
1 2 3 4
5 6 7 8
Series Name
DT3:Delta DT3 Series Temperature Controller
Panel size (W x H)
20:4848:1/16 DIN W48 x H48 mm
30:7272:W72 x H72mm
3
Output 1 options
R: Relay, 250 VAC, 5A
V: Voltage pulse, 12V +10 to 20%
C: DC current, 4 to 20m A
L: Linear voltage, 0 to 10 VDC
4
Power supply
A: AC 80 to 260V
D: DC 24 V
5
Output 2 options
R: Relay, 250 VAC, 5A
V: Voltage pulse, 12V +10 to 20%
C: DC current, 4 to 20 mA
L: Linear voltage, 0 to 10 VDC
6
Optional function 1
0: None, 1: Event input 3, 2: RS-485 communication
7
Optional function 2
0: None, 1: Event input 2, 2: CT input 2, 3:Retransmission output
8
Optional function 3
0: None, 1: Event input 1, 2: CT input 1, 3: Remote setup input
1
2
40:4896:1/8 DIN W48 x H96 mm
60:9696:1/4 DIN W96 x H96 mm
Accessories Information
D T 3 - 1
DT3:Delta DT Series Temperature Controller
Accessories
Option 1
1
20ESTD : DT320 EXTENSION without RS-485 & EV3
R: Relay Output
20ECOM : DT320 EXTENSION include RS-485
V: DC Voltage Pulse Output
20EEV3 : DT320 EXTENSION include EVENT3
C: DC Current Output
30ESTD : DT330 EXTENSION without RS-485 & EV3
L: DC Linear Voltage Output
30ECOM : DT330 EXTENSION include RS-485
EVENT
: Event Input
40ESTD : DT340/DT360 EXTENSION without RS-485 & EV3
CTI
: CT Input
40ECOM : DT340/360 EXTENSION include RS-485
RETRANS : Retransmission
40EEV3 : DT340/360 EXTENSION include EVENT3
REMOTE : Remote set point
CT30A
: 30A CT
CT100A
: 100A CT
Ordering Information
1 2 3 4
5
6 - 7
Series Name
1
2
3
4
Panel size (W x H)
5 Output
1
2
DTA:Delta A Series Temperature Controller
4848:1/16 DIN W48 x H48 mm
4896:1/8 DIN W48 x H96 mm
9696:1/4 DIN W96 x H96 mm
7272: W72 x H72 mm
9648: W96 x H48 mm
R:Relay, SPST (4848: SPST), 250VAC, 5A
V:Voltage pulse, 14V +10% ~ -20% (Max. 40mA)
C:Current, 4~20mA
6
Communication (optional)
0:N/A
1:RS-485 communication
7
CT (optional)
□:N/A
T:With CT (only DTA7272R0)
15
1 2 3 4
5
Series Name
2
1
3
DTB:Delta B Series Temperature Controller
Panel size (W x H)
4
*DTB4824 has no optional function and no extra alarm output. Output 2 can be set to alarm output.
*DTB4848 has only 1 optional alarm output. Output 2 can be set to the 2 nd alarm output.
*DTB9696 has optional valve control function. Model name: DTB9696RRV.
7
6
4824:1/32 DIN W48 x H24 mm
4848:1/16 DIN W48 x H48 mm
4896 :1/8 DIN W48 x H96 mm
9696 :1/4 DIN W96 x H96 mm
5
Output 1 options
R:Relay, SPDT (4824/4848: SPST), 250VAC, 5A
V:Voltage pulse: 14V +10% ~ -20%
C:DC current: 4 ~ 20mA
L:Linear voltage: 0 ~ 5V, 0 ~ 10VDC
6
Output 2 options
R:Relay, SPDT (4824/4848: SPST), 250VAC, 5A
V:Voltage pulse: 14V +10% ~ -20%
7
Optional function
1 2 3 4
□:Without CT, without EVENT input
T:With CT, without EVENT input
5
Series Name
DTC:Delta C Series Temperature Controller
1
Controller type
1 :Main unit
2 :Extension unit
2
Number of auxiliary outputs
0 :Standard 2 outputs, no auxiliary output
Optional function
00:Standard function
01:With CT input
Output
R
V
C
L
4
3
5
1 2 3 4
5
5
1
:Relay, SPST, 250VAC, 3A
:Voltage pulse, 12V +10% ~ -20%
:Current, 4 ~ 20mA
:Linear voltage, 0 ~ 10V
0
Series Name
1 2 3 4
E:Without CT, with EVENT input
V:Valve contro
Panel size (W x H)
DTD:Delta D Series Temperature Controller
4848:1/16 DIN W48 x H48 mm
4896:1/8 DIN W48 x H96 mm
7272:W72 x H72 mm
Output
R:Relay, SPST, 250VAC, 5A
V:Voltage pulse, 14V +10% ~ -20% (Max. 40mA)
0 Optional function
0:N/A
2 3
Series Name
Controller type
1
2
3
Optional function
1 2 3 4
5
Panel size (W x H)
Output
1:Main unit
2:Accessory
0T:4-channel TC (main unit, accessory)
0P:4-channel PT (main unit, accessory)
0V:4 channels of voltage pulse output
0C:4 channels of linear current output
0R:4 channels of relay output
0L:4 channels of linear voltage output
0D:4 digital inputs & 4 digital outputs
CT:4 channels of current transformers
DS:Display & setup module
5
Series Name
1 2 3 4
DTE:Delta E Series Temperature Controller
DTV:Delta V Series Temperature Controller
4896:1/8 DIN W48 x H96 mm
9696:1/4 DIN W96 x H96 mm
R:Relay, SPDT, 250VAC, 5A
16
Dimensions
4824
7272
99.8 mm
72.0 mm
4848
67.80 mm
3.4 mm
74.0 mm
48.0 mm
72.0 mm
24.0 mm
21.85 mm
44.75 mm
13.80 mm
79.20 mm
9648
SET
48.0 mm
9.5 mm
44.0
48.0
48.0 mm
44.75 mm
91.0
80.0 mm
DTA9648
96.0
17
12.3
79.2
4896
9696
90.8 mm
98.0 mm
96.0 mm
91.0 mm
98.2 mm
95.7 mm
44.0 mm
SET
SET
48.0 mm
12.8 mm
79.2 mm
96.0 mm
DTE
90 .0
DTC
15.8 mm
18
79.2 mm
Industrial Automation Headquarters
Delta Electronics, Inc.
Taoyuan Technology Center
No.18, Xinglong Rd., Taoyuan City,
Taoyuan County 33068, Taiwan
TEL: 886-3-362-6301 / FAX: 886-3-371-6301
Asia
Delta Electronics (Jiangsu) Ltd.
Wujiang Plant 3
1688 Jiangxing East Road,
Wujiang Economic Development Zone
Wujiang City, Jiang Su Province,
People's Republic of China (Post code: 215200)
TEL: 86-512-6340-3008 / FAX: 86-769-6340-7290
Delta Greentech (China) Co., Ltd.
238 Min-Xia Road, Pudong District,
ShangHai, P.R.C.
Post code : 201209
TEL: 86-21-58635678 / FAX: 86-21-58630003
Delta Electronics (Japan), Inc.
Tokyo Office
2-1-14 Minato-ku Shibadaimon,
Tokyo 105-0012, Japan
TEL: 81-3-5733-1111 / FAX: 81-3-5733-1211
Delta Electronics (Korea), Inc.
1511, Byucksan Digital Valley 6-cha, Gasan-dong,
Geumcheon-gu, Seoul, Korea, 153-704
TEL: 82-2-515-5303 / FAX: 82-2-515-5302
Delta Electronics Int’l (S) Pte Ltd
4 Kaki Bukit Ave 1, #05-05, Singapore 417939
TEL: 65-6747-5155 / FAX: 65-6744-9228
Delta Electronics (India) Pvt. Ltd.
Plot No 43 Sector 35, HSIIDC
Gurgaon, PIN 122001, Haryana, India
TEL : 91-124-4874900 / FAX : 91-124-4874945
Americas
Delta Products Corporation (USA)
Raleigh Office
P.O. Box 12173,5101 Davis Drive,
Research Triangle Park, NC 27709, U.S.A.
TEL: 1-919-767-3800 / FAX: 1-919-767-8080
Delta Greentech (Brasil) S.A
Sao Paulo Office
Rua Itapeva, 26 - 3° andar Edificio Itapeva One-Bela Vista
01332-000-São Paulo-SP-Brazil
TEL: +55 11 3568-3855 / FAX: +55 11 3568-3865
Europe
Deltronics (The Netherlands) B.V.
Eindhoven Office
De Witbogt 15, 5652 AG Eindhoven, The Netherlands
TEL: 31-40-2592850 / FAX: 31-40-2592851
*We reserve the right to change the information in this catalogue without prior notice.
Delta_DT_C_EN_20130118
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising