gbm 13-2 re professional

gbm 13-2 re professional
2 609 932 509.book Seite 1 Dienstag, 29. November 2005 11:31 11
GBM 13-2 RE
PROFESSIONAL
Operating Instructions
2 609 932 509.book Seite 2 Dienstag, 29. November 2005 11:31 11
2 • 2 609 932 509 • 05.12
2 609 932 509.book Seite 3 Dienstag, 29. November 2005 11:31 11
2 608 180 003
(BS 35)
2 608 180 004
(BS 45)
1 612 025 024
1 613 001 005
2 608 030 053
(MS 65)
2 608 030 055
(MS 80)
2 608 572 105
1 608 571 062
2 607 990 050
(S 41)
3 • 2 609 932 509 • 05.12
2 609 932 509.book Seite 4 Dienstag, 29. November 2005 11:31 11
2
1
3
6
5
4
7
8
10
9
11
GBM 13-2 RE
PROFESSIONAL
4 • 2 609 932 509 • 05.12
2 609 932 509.book Seite 5 Dienstag, 29. November 2005 11:31 11
A
B
8
9
10
12
x
13
C
D
1
2
15
14
E
13
16
5 • 2 609 932 509 • 05.12
2 609 932 509.book Seite 1 Dienstag, 29. November 2005 11:31 11
General Power Tool Safety Warnings
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce the risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an
increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) or an earth leakage
circuit breaker (ELCB). Use of a GFCI or an
ELCB reduces the risk of electric shock.
6 • 2 609 932 509 • TMS • 24.11.05
3) Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol, or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dusk mask, non-skid
safety shoes, hard hat or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off position before connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying power tools with your finger on the
switch or energizing power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or
a key that is left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing
and balance at all times. This enables better
control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing,
and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be
caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dustrelated hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it is designed.
b) Do not use the power tool if the switch
does not turn it on or off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
English - 1
2 609 932 509.book Seite 2 Dienstag, 29. November 2005 11:31 11
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that
may affect the power tool’s operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories, tool bits
etc. in accordance with these instructions, taking into account the working
conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified
by the manufacturer. A charger that is suitable for one type of battery pack may create
a risk of fire when used with another battery
pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and
fire.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects, that can make a connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with
water. In liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
7 • 2 609 932 509 • TMS • 24.11.05
6) Service
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the
safety of the power tool is maintained.
For Your Safety
Read all instructions. Failure to follow all instructions listed below may
result in electric shock, fire and/or
serious injury.
SAVE THESE INSTRUCTIONS.
■ When working with the power tool, always
hold it firmly with both hands and provide
for a secure stance. Both hands guide a
power tool more securely.
■ Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
■ Do not work materials containing asbestos. Asbestos is considered carcinogenic.
■ Take protective measures when dust can
develop during working that is harmful to
one’s health, combustible or explosive. Example: Some dusts are regarded as carcinogenic. Wear a dust mask and work with dust /
chip extraction when connectable.
■ Keep your workplace clean. Material mixtures are particularly dangerous. Dust of light
metal can be inflammable or explode.
■ Always wait until the tool has come to a
complete stop before placing it down. The
tool insert can jam and lead to loss of control
over the power tool.
■ Do not use a power tool with a damaged
power cord. Do not touch the damaged
cord and pull the power plug when the cord
is damaged while working. Damaged cords
increase the risk of an electric shock.
■ Connect power tools that are used in the
open via a ground fault circuit interrupter.
■ Always use the auxiliary handles supplied
with the machine. Loss of control can cause
personal injury.
■ Use appropriate detectors to determine if
utility lines are hidden in the work area or
call the local utility company for assistance.
Contact with electric lines can lead to fire and
electric shock. Damaging a gas line can lead
to explosion. Penetrating a water line causes
property damage or may cause an electric
shock.
English - 2
2 609 932 509.book Seite 3 Dienstag, 29. November 2005 11:31 11
■ Switch off the power tool as soon as the
tool insert jams. Be prepared for a high reaction torque, which will cause a kickback.
The tool insert jams when:
– the power tool is overloaded or
– it becomes wedged in the workpiece.
■ Hold the power tool only by the insulated
gripping surfaces when performing an operation where the cutting tool may contact
hidden wiring or its own power cord. Contact with a “live” wire will also make exposed
metal parts of the power tool “live” and shock
the operator.
Product Features
The numbering of the product features refers to
the representation of the tool on the graphics
page.
While reading the operating instructions, unfold
the graphics page of the tool and leave it open.
1 Keyless chuck*
2 Flat of nut
3 Lock-on button for On/Off switch
4 Speed preselection thumbwheel
5 On/Off switch
6 Rotational direction switch
7 Gear selector
8 Wing bolt for depth stop adjustment
9 Wing bolt for auxiliary handle adjustment
10 Depth stop
11 Auxiliary handle
12 Chuck key*
13 Key chuck*
14 Drive bit*
15 Drill spindle with hexagon socket
16 Locking screw
* Not all of the illustrated or described accessories are
included as standard delivery.
8 • 2 609 932 509 • TMS • 24.11.05
Tool Specifications
Drill
Article number
Rated power input
Output power
No-load speed
1st gear
2nd gear
Rated speed
1st gear
2nd gear
Rated torque
(1st/2nd gear)
Infinitely variable
speed control
Right/left rotation
Chuck clamping
range, max.
Max. drilling Ø
(1st/2nd gear)
Steel
Wood
Aluminum
Weight according
to EPTA-Procedure 01/2003
Safety class
[W]
[W]
GBM 13-2 RE
PROFESSIONAL
0 601 169 5..
550
285
[rpm]
[rpm]
0 – 1 000
0 – 1 900
[rpm]
[rpm]
0 – 550
0 – 1 000
[Nm]
11.5/6.0
●
●
[mm]
1 – 13
[mm]
[mm]
[mm]
13/8
32/20
20/12
[kg]
1.9
/ II
Please observe the article number on the type plate of your
machine. The trade names of the individual machines may
vary.
The values given are valid for nominal voltages [U] of
230/240 V. However, these values can vary for lower voltages and models made for specific countries.
Noise/Vibration Information
Measured values determined according to
EN 60 745.
The A-weighted sound pressure level of the
tool is typically 80 dB (A). Measuring inaccuracy
K = 3 dB.
The noise level when working can exceed
85 dB (A).
Wear hearing protection!
The weighted acceleration is typically 3.0 m/s2.
The vibration emission level given
in this information sheet has been
measured in accordance with a standardized test
given in EN 60 745 and may be used to compare
one tool with another.
The vibration emission level will vary because of
the ways in which a power tool can be used and
may increase above the level given in this infor-
English - 3
2 609 932 509.book Seite 4 Dienstag, 29. November 2005 11:31 11
mation sheet. This could lead to a significant underestimate of exposure when the tool is used
regularly in such a way.
NOTE: To be accurate, an estimation of the level
of exposure to vibration experienced during a
given period of work should also take into account the times when the tool is switched off and
when it is running but not actually doing the job.
This may significantly reduce the exposure level
over the total working period.
Intended Use
The machine is intended for drilling in wood,
metal, ceramic and plastic. Machines with electronic control and right/left rotation are also suitable for screwing and thread cutting.
Auxiliary Handle/Depth Stop
(see figure A )
The auxiliary handle can be mounted on the right
or left side of the spindle neck with the wing
screw 9.
The drilling depth can be set with the depth
stop 10.
For this, loosen wing bolt for depth stop adjustment 8, set the required drilling depth X and
tighten the wing bolt again.
The knurled surface on the depth stop 10 must
face upwards.
Inserting the Tool
Key Chuck (see figure
B
)
Open the chuck until the tool can be inserted.
Then, insert the tool.
Using the chuck key 12, tighten uniformly in all
three holes.
Keyless Chuck (see figure
C
D
)
The drill spindle 15 is equipped with a hexagon
socket for use with screwdriver bits 14. The bit
can be inserted directly into the drill spindle 15
when the chuck is removed, where it is retained
by a securing ring.
Initial Operation
Always use the correct voltage: The voltage of
the power source must agree with the values on
the nameplate of the tool.
Switching On and Off
To start the tool, press the On/Off switch 5 and
keep it pressed.
The machine runs with variable
speed between 0 and maximum
depending on the pressure applied
to the On/Off switch 5. Light pressure results in a low rotational
speed, thus allowing smooth, controlled starts. Do not strain the machine so
heavily that it comes to a standstill.
Lock the pressed On/Off switch 5 by pressing
the lock-on button 3.
To switch the tool off, release the On/Off
switch 5 or press and then release it.
Changing the Rotational Direction
Operate the rotational direction switch 6 only
at a standstill.
Set the rotational direction switch 6 to R (righthand rotation) or L (left-hand rotation). (When the
On/Off switch 5 is actuated, the rotational direction switch 6 is locked.)
The left-hand rotation enables screws or nuts to
be unscrewed.
Mechanical Gear Selection
)
Inserting the Tool
Hold the rear sleeve of the keyless chuck 1 tight
and open the chuck by turning the front sleeve,
until the tool can be inserted.
Tightening the Tool
Hold the rear sleeve tight and firmly tighten the
front sleeve by hand, until the locking action (“click”) is no longer heard. The drill chuck is
locked automatically.
The locking mechanism loosens when the sleeve
is turned in the opposite direction for removing
the tool.
9 • 2 609 932 509 • TMS • 24.11.05
Screwdriving Tools (see figure
Two speed ranges can be preselected with the
gear selector 7:
Gear I:
Lower r.p.m. range
Gear II:
Higher r.p.m. range
The speed can be switched during drilling operation. However, this should not be done while operating at full load.
Speed Preselection
With the thumbwheel 4, the required speed can
be selected even if the machine is running.
English - 4
2 609 932 509.book Seite 5 Dienstag, 29. November 2005 11:31 11
Replacing the Chuck (see figure
E
)
■ Before any work on the tool itself, pull the
power plug.
Removing the Locking Screw
The locking screw 16 secures the drill chuck
against loosening from the drill spindle. Fully
open the drill chuck and completely unscrew the
locking screw 16 by turning it clockwise.
If the locking screw is seated tight, apply screwdriver to the head of the screw and loosen it by
giving the screwdriver handle a sharp blow.
Unscrewing the Chuck
Key Chuck
To unscrew key chuck 13, position an open-end
wrench (size 17 mm) against the wrench flats.
Place the chuck key in one of the 3 holes and
loosen the chuck by turning it to the left using the
key as a lever. If the key chuck is frozen in place,
a light blow on the chuck key should loosen it.
Keyless Chuck
Insert hexagon tool (Allen key or screwdriver bit)
into the chuck and clamp the free end in a vise.
Position open-end wrench against the wrench
flats of the drill spindle and loosen chuck in a counterclockwise direction, as if loosening a screw.
The keyless chuck is mounted in reverse order.
The chuck must be tightened with a
tightening torque of approx. 15 Nm.
Operating Instructions
■ Apply the power tool to the screw /nut only
when it is switched off.
The required speed depends on the material and
can be determined with practical trials.
After working with the machine for long periods at
low speed, allow it to cool by letting it run for approx. 3 minutes at maximum speed with no load.
Sharpening Drill Bits
When drilling in metal, use only perfectly sharpened HSS (high-speed steel) drill bits. The appropriate quality is guaranteed by the Bosch accessories program.
Twist drills from 2.5–10 mm can easily be sharpened with the drill sharpener (see accessories).
Bench Stand
We recommend the use of a bench stand (see
accessories) especially when work demanding
more precision is required.
10 • 2 609 932 509 • TMS • 24.11.05
Machine Vise
The machine vise (available as an accessory) facilitates a safe tightening of workpieces, preventing their twisting and any accidents this would
cause.
Maintenance and Cleaning
■ Before any work on the tool itself, pull the
power plug.
■ For safe and proper working, always keep the
machine and the ventilation slots clean.
If the power tool should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
center for Bosch power tools.
In all correspondence and spare parts orders,
please always include the 10-digit article number
given on the nameplate of the power tool.
Disposal
Power tools, accessories and packaging should
be sorted for environmental-friendly recycling.
Service
Exploded views and information on spare
parts can be found under:
www.bosch-pt.com
In case of a claim, repair or purchase of replacement parts or in case of queries or other problems, please contact your local dealer or Bosch
representative.
People’s Republic of China
Website: www.bosch-pt.com.cn
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: .................................... 800 8 20 84 84
✆ .................................................... +86 571 87 77 43 38
Fax ................................................... +86 571 87 77 45 02
HK and Macau Special Administrative Regions
Room 1210, Shun Tak Centre, West-Tower,
168 – 200 Connaught Road, Central Hong Kong
Customer Service Hotline: ....... +852 25 89 15 61
Fax .......................................................... +852 25 48 79 14
E-Mail: bosch@melchers.com.hk
Subject to change
English - 5
2 609 932 509.book Seite 1 Dienstag, 29. November 2005 11:31 11
ê ë9:
ë9:;
; Ÿ v ó !"# $ %&'()*+
,- ./
./ 0 1 23
,-./
4
56789:;8<=>
?@A9:; BCDEF67GH
9:; BIEF
1) : J K
KL
LMN
a) : J = > .OPQ
.O PQ"
PQ " # R S T U V WX%YZ:J[\]^
b) _ 5
`
5
` abc
abc
de
def
f g9:
g9:;
;
de < Uh
kl ` abc
abc
de<
Uhi
i \ j kl
mn % op:
op: J qrstuv
mn%
w w[\xjop%\jyz
c) qrs
qr s _ {|
{ | } %~
‚ : %~
 € ‚:
J :sƒ„…†‡€ˆ‰Š‹Œ
]Ž
67 r 7 ‘ KL
K L 2) 67
a) 67
’ “ = > ” C•
9: ; ’
–
67’
’“
C•9:
9:;
’–
˜™ š ›œ’
— ˜™š
›œ’–
–  @ ’ – _ 0 @i
9: ; Ÿ 67
ž E 9:;
67
67qr¡¢s
£¤’–•¥’“0¦§¨©
bc
b) ª «{¬l
«{ ¬l­
ž ¯l
¯l °±
° ± ²
¬l ­ ® @ ž¯l
³r ´
´µ
Œ ³r
´ µ ¶ · ƒ¸¬l@
ži¹º[\¨©
qr = >»¼
>» ¼ ½±%
½± % ¾ ¿ ƒ{±ÀÁ9
c) qr=
:;t€¨©bc
žÄ Å E _
_
067
067
EÆ
EÆ9
9
d) à žÄÅ
: ; Ç È9:
;% € 0 É Ê E Ë
Ì
È9:;%
;%€
ËÌ
Í¡’ – ÐÑ Ò
Í¡’–
E
E = >»
>»¼
¼ Â Î Ï ÐÑÒ
Ó Ô %  9 qÕ
qÕ Eƒ©Ö%×Ø
ÓÔ
5Ÿ t€¨©bc
e) ƒ 5 Ù ^67
67 • ¥ ^679:
9:;
9: ; Ú 67•
Ù ^ Û 7Ü
7ÜÝ
Ý E 67•ÞÙ^Û7ÜÝ
E¦§€¨©bc
ߪ « =
de 67
=>5
>5à
>5 à ¾ de
f) ƒ I ߪ«
g9: ; á
g9:;
á67â
67âã
67â ã ä . åæ
åæç
ç 6
7âãä.åæç0è騩
11 • 2 609 932 509 • TMS • 24.11.05
€ KL
K L 3) ê ë
ë€
€K
a) : sì
= T L í î  _ï
T .O
– ðñ
sì=
_ïT
.O–
ò › T Å ó ž
ž
9:
9:;
; ô õö
õö÷%
÷%
ø 7 ù ‘ ú û ü ý¯
ý¯þ
þ3—˜
9:
9:;
; 679:;sÚT‹1
v3ƒ()]^
D" å
å b) ¸
¸ é
éå
å ¤ D"
679:;•¥éå¤D°éo
:KL%¦§:
*+vq
9 qr
’ ’ – " # $ %K ¤ G
c) ª « ]^
]^
qr
H
Hþ
þ %
%
qr
qrþ
þì=
49:
Ä 5 ç
ç ƒ¸5Æ
49:;
; < Ä5
9:;s!­®iæç%"5?@A
s #æç$%&'5æ9()*+,
-()]^
99: ; þ = > ./
$% ’ 5 qr
qr d) æ 99:;
./$%
$%’
0 1 : ; $ %23
%2 3 4 ! ƒqr56æ7
01
9 8 Šqr
$%’"01:;9[\*+
67€
sT . >
e) ª « : ; O
Oq
q < = qr
qrsT
sT
V ? @"TAs
@" TAs.O
TAs .OBC
.O BC
BC Ã<=
”DE¸5F fGsHI9:;
:
ø:
ø:
s_0JKL
f) " • ¥ :
M ø
N _ 0 OP
_ 0 { – øN
OP_
_
M ø !Q
qr  9 qÕ
qÕ KLM
!Q@
@ ® qr
¯Ý%OP[\RSÁ9qÕ
¤) U o ¤ D
qr
K ¤ T o ¤)
g) ƒ ” 5 qr
ì =VR
=V R
R K ¤ W X Y E : ; "
"#
#Ã
ž
¤) 67To¤D0é:o
ž
Z ¤)
b+l
[ž
ž 67
67
Ä Å 9:
9:;
;
4) [
a) ˜ {qr
_` : ó a b
{qr\
\ ] ^ ) _`
c¥ • 9:
c¥•
9:;
; Þb79:;0
5M'def›
g›KL
qr
b) ˜67
æ çh
i 9:
; ƒIßú
˜67æ
çhi
9:;
 #æç-[\5qrsuv]^
jklhiqrmn
'› opÕ%_
opÕ% _ 67
qr s qr&
& '›opÕ%
67qr
qrs
c) 5 0 1 qr
*= >q’
> q’“
q’ “ Í¡’
*=>
Í¡’–
–"# $ % r¡G
H sèétu0ª«_[æ99
:;
- 1
2 609 932 509.book Seite 2 Dienstag, 29. November 2005 11:31 11
d) _ 679:
67 9:;
9: ; s =>
= > w qr/x
qr /x5
/x 5 | }
I ß r á þ Ę
Ä ˜ { _ yzqr
yz qr
qr ËßG
Ëß G
g { S | 67g
67 g qr
qr {6}_V
g
g{
9:;[\v]^
: K L
ê ë ¸ :
> {S
{ S Â0f
= >
Ã[\¨©x !%+
,()*+
e) ~
ž.  € å 9:;
9: ; 4 qr
~ž.
ž.
qr
 9 pÕ<
pÕ < ú"
à º"
º" ' < pÕ
 ‚%Ö
‚% Ö ƒ hi
h i qÕt„…
qÕt „…9:
„… 9:;
9: ; d 67qr
67 qrþ
o% n Å
qr þ ì = › o%n
h i qÕ
qÕ †‡ˆ‰Šqr€å:[
\:]^
Ä,-./g67
f) — ‹:;
‹: ; = > .OÑÒ
.OÑ Ò ñŒ
ñŒ 6^~.
Š#ŽÑҗ‹:;_\RIŠ#[
\
■ @':
@':Õ
Õ 67@'¤)%ÉÊ˔›
KL?@žÌ:Õ
‘ 67
9: ; CÕG
K¤ 5
g) Rs
Rs‘
679:
9:;
CÕGK
qr :;
: ; ’ ^N=
^N = >  ]
ç
]
ç qr
qr qr
Ë Ì Gqr¥7
Gqr ¥7e
¥7 e f “ { ƒ679
:;‰Š_”•Zqró:-[\v
]^
5) [ž
[ ž 67
67 Ä Å UÌ
U Ì qr
67 H +•–—
+•– — Ur
U r …GHU
…G HU
a) Ú 67H
_067ê똑™'GHUr…&
'GHUx !
b) ì = 679:
67 9:;
9: ; Û 7GH
7G H 67i_•
¥GHv:]^◗›x !
67 G H=>»
H= >»¼œ
¼œ  ê ž Ÿ Ÿ >» ¼œ
c) _ 67
¡¢
£ 2 3 %&
' ¤ ¥¯l
¦¯
¡¢£
%&'
¥¯l
l ?@G
?@ G H
H ®§x
®§ x ¨ © GH
ª®§ƒv¨©x !
67 _«
_« q
q G HÀ
H À ¡ klª
kl ª«
ª «
d) ƒ 67_«
@ ®WXä
®W Xä9
Xä 9 ¯l
¯l ƒ_[
ƒ_ [®
[ ® ¬i
¬i ­
7± ® ¯ ƒ ¦kl°Á
¦kl °Á±
°Á ± ² = > ³
7±®
´µ ¶ qGHä¡klt·¸%¹*º
´µ¶
»
6) n ø ì
l 9:;¼
9: ;¼½
;¼ ½ • ÞÛ
Þ Û ¾ ¿ n a) Ú l9:
ns
Ú o
¤ £ ¢ p CÕ
CÕ À
WÁ
nsÚ
o¤
.qrKLó
>0Å!Æ Ç 9:;
9: ; "#
" # T ■ : s = >0Å!ÆÇ
@
. > V ? @67Å!9:;Ȑ?'
KL
■ ˜ Í :ÎÏ
:Î Ï Ð ¯ Ñ ÏÐ<Ò¯a
ƒ qrs
qr s t u v
+
v
+ ÓÔ
ÓÔ \ j%
■ ƒ
x `Õoì
`Õo ì =Ö
r ¥ «é
å t u °
=Ör
«éå
ê똑Ò×opì=
éo
;ƒ”5qr
K¤TorNTͤW
qÕ
■ : J T.O
T .O1
.O 1 Œ ¯Ñ6^ؕ3;
Ù«ÂbcóÚ¤¥o[\jÛ%`a
■ = > ·Ü9:;
·Ü9: ; Ý LÞ
LÞ 3 Á
Á 0 x f
qr K¤5qr
:;RßIàŠI
qr
ߐH9:;
˜67 E©Ö
E©Ö qr
qr ƒA
ƒ A E5:
E5 : ■ ˜67
Ö ƒi%
 ‚i
á â _ ® ¬ E =
>
ƒi%
‚i
=>
Í¡’ – 67փE[\®
­ Í¡’–
^67 qrs
qr s = > K ¤ â ã ä B FIFé
Fé
■ 5 Ù ^67qr
åæ ç
åæç
67 ãÎ5
ãÎ 5 9:;
9: ; ä å e f YE
Y E w
■ ì = 67ãÎ
! :sƒIßÐHqrR‹*
é ê þ
■ 0 • ¥ þ æ ç r è 4 ¾ e f < éê
²ë= Ts>쫞
Ts>ì «ží
«ž í & î ( Äï
E © ²ë=Ts>ì
ðñ
:sƒòióEt !"¨©
փimn²tx `a‹i±²_ô
t+,õ¯Öqr€N„W®
ƒK ¤ 5 qr
qr :;
: ; RßI
Rß I i =>
= > ­ ■ ƒK¤
ç9: ; = >Asée
>As ée„…
ée„…qr
„… qrö®
qr ö®
ç9:;
Šu v ÷ øöù
øö ù úŽ
úŽ K¤5qr
:;
Šuv
tRßI°û
– 9:;Ä5ü`ý%€
– :;5:Õþi
ƒK ¤ 5 qr
qr ;
 ;
;  é
■ : s ƒK¤
E %qrg
%qr g ¬ AE
AE
AE Ÿ ' T
E
Ô! 9:;
9: ; 9:;ƒ@
Æ " Ô!
®iEqr
¤¥Õt"
€®
12 • 2 609 932 509 • TMS • 24.11.05
- 2
2 609 932 509.book Seite 3 Dienstag, 29. November 2005 11:31 11
qÕ
qr MÞ
qrMÞ
qÕqr“
Ÿ
%
67{S|sÄæ
qՓ{
01As4
1 k– 2 4!K’()
3 #æç
4 01
5 #æç
6 Ýæç
7 bæç
8 01þ2
9 01YEw!þ2
10 11 YEw!
12 –4! 13 d– 14 23
!
15 "#$%&
16 @'23
Ÿv'
)Õ
f ¼ (å‘
( å‘_
å‘ _Ÿ
') %
{ G _ Ÿ ')
% {
¯‘?@
AÁd
A¡d
I_]
†Ÿ
†C
D'
†Ÿ
†C
D'úŽ
✜ † 1$ † 2 ✢
IJ̞01
Ý $ d
–þKxef 8
Lø
Lø%NOP
✜ † 1$ † 2 ✢
Q
RS
T
)/”•UVWtX
YZ'[\ (EPTA)
2003 ] 1 ^W6
¡M'
Ô·`
[m]
[m]
GBM 13-2 RE
PROFESSIONAL
0 601 169 5..
550
285
[ B $ ‹ ] 0 – 1 000
[ B $ ‹ ] 0 – 1 900
[ B $ ‹ ] 0 – 550
[ B $ ‹ ] 0 – 1 000
[ GHI ] 11,5/6,0
●
●
[ MI ]
1 – 13
[ MI ]
[ MI ]
[ MI ]
13/8
32/20
20/12
[ á_ ]
1,9
/ II
ì=añ9:;bc
¯‘?@dŸqr;D_d
¯‘ef
ggÑ+êë 230/240 (V) h™8f-_¥7i§žj0G
™k7M'lm
2, G 4 9 g Ñ
2,G
g*+ EN 60 745 M'çá
gqr,- A *.º< 80 dB (A)ç/;
0 K = 3 dB
:s2,*ü^ 85 dB (A)
Ä
å3
Í*… 3,0 m/s2 g{S|ä45±B<
EN 60 745 M'ç/^6çá
gç/*…&7qrȐ89
g45±BtA"9:;ù7:;Šœ<
5˜‘' fqr45±Btü=g{S|
ä45*ƒ6º5
¦ f679
:;t§>iqr45_]
13 • 2 609 932 509 • TMS • 24.11.05
- 3
2 609 932 509.book Seite 4 Dienstag, 29. November 2005 11:31 11
ûƒT9žZ>9:;5™'sn"
45_]±Bo=>pGçqsnqrq
Ürsn
¦sntSs¦§qr5tç/
sn"45_]6
qr þ qrþ
Ä 67
67Ã
à - ûA-=>‘qr’c
äMޟ
æ9 $ ç
67 qr
à ž 67qr
gqr¥•5uvwr¤¥GRS
àŠ%N
¾CDi90x¤)Gà $ dqr
Ny2yG%H2z
æ 9 qrVf #æç
qr
5 ".OVIý
✢
€5 #æç 5 uŽø[
œ<œ<ef5 0 ‡Lø
n uŽ[§ %“?[
\H ˜{qr„\©^ø_`
Š#
Ò72 9lYEw!K¤5&{þ|
}%~}
@'
567 #æç 3 'RVI
@' #æç
þ #æç
67 10 &'%N
5 %Vf #æç"A³
ç qrxæ #æç
qr
çqr
l&xæ
Y E w ! $ ✜ „ … ’ A
Læ01þ2 8&'þ%N
X €Ç2
10 þ‚z=>ƒ
« qr
ýs Á Ã
qrÄ
Ä i Þ ýs
ýsÁ
Ã
 æ ç 6
Ýæç 6 &'… R BÝF% L BF
Bƒ 9i #æç 5Ýæç 6 1tR
'F
K¤:;
d – ✜ „ … ’ d–
B
✢
lqr015()L23%2”
†æ–‡0’Á%– B:;F…K¤
:;
0–4! 12 ’Á–
þ‡N"ˆ‰ž
Ç
k– ✜ „…’
<oì
C
✢
K¤:;
ÆÇk– 1 þ3QŠ@"€0yþ9
‹†æQŠ=>l&†æ‡0’Á%–…
ÇCÕ
ÆÇ3QŠ%30!7ŽžÇQŠ‡_€
ŒŽÁ… B8_Ž_8F…Ws–56
š9'
lQŠƒ"ÙöËì91r¡%–59
ds'dtš9“/
23 £– ✜ „…’
D
✢
%& 15 0K¤23 ! 14.f–þ3
0O@w23 !K¤5%& 15 Ws@'
dtð !
!9o
Ò7bæç 7 àŠªJþ<oû
†Ÿû
§ef
†Cû
ef
5qrN0oï<5qr^]s•˜
o
0b
6701 4 &'Tþ B5qrN
àŠ01F
o – ✜ „ … ’ › o–
E
✢
■ ëqr–—on:þŸ'TÍ¡
’–
./@' 2 3
./@'2
@'23 16 w–@'5%&
0鏖
˜¼w–ÝL†æ™"sêì¡
23 16
ƒ@'23ŽIi0w23 £x523
–
"ښ23 £³0Læ23
14 • 2 609 932 509 • TMS • 24.11.05
- 4
2 609 932 509.book Seite 5 Dienstag, 29. November 2005 11:31 11
¡–
€ å ‘ ñŒ
d –
d–
›¡d–0æœ4! (SW 17) ld
– 13 @'
w–4!’Á–
þ–—ŸN B–

3 NF"dy23Ÿv~L揖
ƒd–ŽIIߝLښ4!0Læ
–
k–
w#$:; B#$4!%23 £–F’Á–
"0ÊË@':;þ’Ÿžlæœ4!’x
5&
þ4!’xÄ"dL23Ÿv
ì~90Ÿf–
■ ëqr–—on:þŸ'TÍ¡
’–
■ 6º.Oqr‘.¿NþñŒ01Ò:àŠ
".:KL
·%g´µvuqr*6^(¸‘a4
ï$
¹ilqrm¼ Bosch 9:;´µ
º»p¼øìÄnÅ
54½¾¿)Õsì=¤85qrbc
10 (À¯‘?@
Õ¯ÄÅ
…i…ùd.9:;)Õã¤SÑ=>
~‹X01ÒgAœ
K¤–•0 ¡àŠ
y Ǐ
–
= >0 15 G H I þ úŽ
úŽy
Ǐ–
øì
¸
¸0
0 q 0f
0f
Á Â 4 qr
qr‹
‹“
‹ “ D Õ ~ g Ñ û
~g
www.bosch-pt.com
■ ç9:
%3 € w:;
w: ; x ) 5 2 3 $
ç9:;
; %3€
2” 2”
ç.Àn%›opÕÄÅÄì•Þ6Æ
•4½
Å¢þt„SÑ_dŠœ<À
£Á
ᤥƒ
ÇÈ
Çȝ
l
qr5ݦ0§þ3{&5q]
f0L9§ 3 ‹¨‹àŠ©ª
«¬%–
%¤¥=>67Ý«¬^ HSS %– BHSS
­Âdk—‹QF Bosch CÕ®¯
”•
W‘a%–
67%–«¬r B„…CÕFÚ\ž°¬
2,5–10 MIþ2y%–
løÉ
lø É
ÊË9:; BlF
Ì´µ
lÍÎÏÐÑÒ
ÓÎjÓÔ© 567 Ô 310052
¼Ùøì³EûÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕ 800 8 20 84 84
Ö ûÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕ +86 571 87 77 43 38
×ØûÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕ +86 571 87 77 45 02
ÙÚÛܙ݊Þj
ÙÚ
dˆßë 168 – 200 àᓠ1210 â
%±²
àŠ³þ%N¾sÄ67%±² B„…
CÕF
¼Ùøì³E ûÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕ +852 25 89 15 61
×ØûÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕ +852 25 48 79 14
Ôûbosch@melchers.com.hk
ÉÊË
ÉÊË¥ig´µþCÕ®¯u‘7‹ÇÍ
:SÑèéSÑ5¾¶9„Š]^
15 • 2 609 932 509 • TMS • 24.11.05
ÁÂûwww.bosch-pt.com.cn
. 㠛œ»
›œ »
- 5
2 609 932 509.book Seite 1 Dienstag, 29. November 2005 11:31 11
Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
www.bosch-pt.com
2 609 932 509 (05.12) O / 16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising