comfort you deserve
COMFORT YOU DESERVE
N O B O ‘ E ’ S E R I E S S L I M L I N E R A D I A N T PA N E L H E AT E R S
WITH LIFETIME PRODUCT WARRANTY
c h O O s e N O B O h e At i N g
The Norwegian company NOBO commenced making panel heaters in 1949 and is one of Europe’s largest manufacturers
of panel heaters. The company is well known for its innovate products, high quality and modern design. NOBO’s clever
design, incorporating a top mounted heat outlet, sets it apart from other panel heaters and enables them to be used
in circumstances (for example behind furniture) where other panel heaters are not as effective or practical.
NOBO Slimline Radiant Panel Heaters have the following advantages over other brands of panel heaters:
- Attractive, modern clean face with no front grill
- Slimline – only 50mm thick
- Cheap to run – independent running
- Large panel surface area equals greater
costs documented and available
radiant heat, and more comfort
- Safer, low surface temperature on the front panel
- Can be located close to or behind furniture
- Power point and cable out of sight behind the heater
D u A l h e At
D u A l h e At
NOBO Radiant Slimline Panel Heaters warm your room
with a combination of both radiant and convection heat.
Convection heat is gently distributed throughout the room
through the top of the panel heater. NOBO’s unique design
draws in cold air across the entire width of the panel,
heating it as it passes over the element, producing natural
convection (without a fan).
CONVE
CTION
H E AT
WA R M
AIR
RAD
COO
IANT
H E AT
LA
IR
Just like the sun, radiant heat is multi-directional, and works
on the principle of warming surfaces and objects within a
room. Radiant heat is universally regarded as a very efficient,
healthy and comfortable method of heating.
With NOBO both types of heat happen simultaneously
– resulting in the dual process of heating the room from
the floor up (with radiant heat), and from the ceiling
down (with convection heat), ensuring a quick start up,
effective performance, and economical operation.
eNergY efficieNcY
NOBO Slimline Radiant Panel Heaters are rated as 100%
efficient because all energy used is converted to heating
your room. There are no fans, or mechanical moving parts
to waste energy or break down.
Accurate electronic thermostats also ensure efficiency.
Further economies and convenience can be achieved by
installing timer models for automatic on/off operation. Due to
their rapid start up, it is recommended to operate your NOBO
panel heaters only for the hours heating is required. Or with
the convenience of the timer models, preheat your room by
programming it to switch on 15 - 30 minutes before use.
rOOm ZONiNg
- Efficiency: In a typical room, there are more objects
down low at people level. When these objects are heated,
they have the ability to maintain the heat in the room for
longer periods of time.
The most efficient, economical and comfortable way to heat
your home is on a room by room basis. NOBO Slimline Radiant
Panel Heaters can provide independent zoning for every room
or living area.
- Health: Radiant heat does not create air movement,
therefore dust and air borne particles are not distributed
around the room.
NOBO Slimline Radiant Panel Heaters are often used in
conjunction with other heating systems. This typically applies
when a large or open living area has its own heat source,
for example a reverse cycle heating and air conditioning
system or gas fireplace, complemented with NOBO panels in
the bathrooms and smaller rooms such as studies. This results
in an integrated, flexible and fully zoned system.
- Comfort: The absence of air movement helps to maintain
your own body temperature.
‘E’ SERIES PRODUCT RANGE
E4E07 - without timer E4EU07 - with timer
Dimensions (W×H×D)
625mm × 400mm × 50mm
Approx. area heated*
9.5m² - Small En Suite
Watts
750
Running Cost*
5 cents / hour as tested
E4E10 - without timer E4EU10 - with timer
Dimensions (W×H×D)
775mm × 400mm × 50mm
Approx. area heated* 12.5m² - Bathroom / Bedroom 3 or 4
Watts
1000
Running Cost*
6 cents / hour as tested
E4E12 - without timer E4EU12 - with timer
Dimensions (W×H×D)
975mm × 400mm × 50mm
Approx. area heated*
15m² - Study / Bedroom 2
/ Smaller Bedroom 1
Watts
1250
Running Cost*
8 cents / hour as tested
E4E15 - without timer E4EU15 - with timer
Dimensions (W×H×D)
1125mm × 400mm × 50mm
Approx. area heated*
19m² - Average Bedroom 1
Watts
1500
Running Cost*
9 cents / hour as tested
LIFETIME PRODUCT WARRANTY: NOBO E Series panel heaters are warranted for their lifetime.
E4E20C Compact - without timer
E4EU20C Compact - with timer
Dimensions (W×H×D)
1125mm × 400mm × 50mm
Approx. area heated*
25m² - Living Area
/ Larger Bedroom
Watts
2000
Running Cost*
13 cents / hour as tested
E4E24 - without timer E4EU24 - with timer
Dimensions (W×H×D)
1525mm × 400mm × 50mm
Approx. area heated*
30m² - Larger Living Area
Watts
2400
Running Cost*
15 cents / hour as tested
E2E12 Skirting Model - without timer
Dimensions (W×H×D)
1525mm × 200mm × 50mm
Approx. area heated*
15m² - Study / Bedroom 2
/ Smaller Bedroom
Watts
1200
Running Cost*
8 cents / hour as tested
* Running cost calculated using a tariff rate of 12.5 cents per kilowatt hour.
See the next two pages for information on panel heater selection, installation (permanent and portable) and running costs.
S I Z I N G C H A R T A N D PA N E L H E AT E R S E L E C T I O N
For effective and efficient performance of your heating system, it is essential to size the heating system’s output to the area, or room
size being heated. Factors which impact the heating effectiveness, such as insulation, building construction etc. must also be allowed
for by applying the “Correction Factors” below.
Step 1 – Determine the correct wattage needed for a room built to current construction standards
- Ceiling insulation rated at minimum R2.5
- External wall insulation rated at minimum R1.5
- Ceiling height up to 2.6 metres - Window coverings with insulating properties
- Window area up to 35% of external wall area
Measure the width (W) and length (L) of the room in metres (M) and use the Sizing Chart below to determine the wattage needed to
heat the room. Rooms with an irregular shape, or with an adjoining open space such as an entry/hallway, can be sized by “squaring”
them off to make several rectangles, and totalling the wattage required. Wattage required is typically 80 watts per square metre of
floor area of the room.
WxL
1.0 M
1.5 M
2.0 M
2.5 M
3.0 M
3.5 M
4.0 M
4.5 M
5.0 M
5.5 M
6.0 M
6.5 M
7.0 M
7.5 M
8.0 M
1.0 M
80
120
160
200
240
280
320
360
400
440
480
520
560
600
640
1.5 M
120
180
240
300
360
420
480
540
600
660
720
780
840
900
960
2.0 M
160
240
320
400
480
560
640
720
800
880
960
1040
1120
1200
1280
2.5 M
200
300
400
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
3.0 M
240
360
480
600
720
840
960
1080
1200
1320
1440
1560
1680
1800
1920
3.5 M
280
420
560
700
840
980
1120
1260
1400
1540
1680
1820
1960
2100
2240
4.0 M
320
480
640
800
960
1120
1280
1440
1600
1760
1920
2080
2240
2400
2560
4.5 M
360
540
720
900
1080
1260
1440
1620
1800
1980
2160
2340
2520
2700
2880
5.0 M
400
600
800
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
3200
Step 2 – Apply Correction Factors if applicable
Add 40% to wattage for one
or more of these factors
Add 20% to wattage for one
or more of these factors
Deduct 20% from wattage for
one or more of these factors
- Bathrooms or en suites
- Solid brick
- Living area with void or stairway
to upper level
- Ceiling height above 2.6 metres
- Window area more than 35% of
external wall area
- No ceiling insulation or insulation
rated less than R2.5
- No wall insulation
- Ceiling insulation rated at R3 and above
- Double glazed windows
Note: In some instances, several “Correction Factors” are required.
Eg: A solid brick room with 3.3m ceilings, requires a “Correction Factor” of an Extra 60%.
Step 3 – Panel Heater Selection
Once the required wattage has been determined, simply refer to the available NOBO models in the chart below and select the most
suitable size heater or combination of heaters to suit your determined wattage. Note that it always safer to “upsize” the wattage
output. If the required wattage exceeds 2400 watts (the largest panel size), more than one NOBO must be installed. A combination of
any size NOBO panel heaters can be selected, providing the total installed wattage matches or exceeds the determined wattage.
Model
(without timer
/ with timer)
Watts
E4E07 / E4EU07
750
E4E10 / E4EU10
E4E12 / E4EU12
Approx.
Running Cost*
(cents per hour)
Dimensions
(L×H×W mm)
Approx.
Area Heated
(m2)
20
24
28
3.12
625×400×50
9.5
5
6
8
9
11
Small En Suite
1000
4.16
775×400×50
12.5
6
9
10
12
14
Bathroom / Bedroom 3 or 4
1250
5.20
975×400×50
15
8
11
13
15
18
Study / Bedroom 2 / Smaller Bedroom 1
Amps
Suggested Placement
Tariff c/kWH
12.5 17
E4E15 / E4EU15
1500
6.25
1125×400×50
19
9
13
15
18
21
Average Bedroom 1
E4E20C / E4EU20C
2000
8.33
1125×400×50
25
13
17
20
24
28
Larger Bedroom / Living Area
E4E24 / E4EU24
2400
10.00
1525×400×50
30
15
20
24
29
34
Larger Living Area
E2E12
1250
5.20
1525×200×50
15
8
11
13
15
18
Study / Bedroom 2 / Smaller Bedroom 1
* See opposite page for more information on running costs.
P E R M A N E N T A N D P O R TA B L E I N S TA L L AT I O N
Each NOBO panel heater comes complete with a wall mounting bracket, and is easily installed on a plaster, timber or masonry wall by
following the instructions provided. Four fixing points are required. Wall mates or toggles straight into plaster is sufficient – locating
a stud is not essential. For a clean appearance, NOBO panel heaters can be installed in front of a standard power outlet.
400
70
200
E SERIES DIMENSIONS
A
L
B
Width
Model
(without timer
/ with timer)
Watts
Width
(mm)
A
(mm)
L
(mm)
B
(mm)
E4E07 / E4EU07
750
625
162.5
300
162.5
E4E10 / E4EU10
1000
775
187.5
400
187.5
E4E12 / E4EU12
1250
975
187.5
600
187.5
E4E15 / E4EU15
1500
1125
262.5
600
262.5
E4E20C / E4EU20C
2000
1125
262.5
600
262.5
E4E24 / E4EU24
2400
1525
262.5
1000
262.5
Shelf, Bench Overhang
or Window Sill
4
3
130
10
2
50
70
1
The bracket design allows the panel
heater to be unclipped and tilted
forward for cleaning and access to
the power point.
Minimum clearances (mm)
The recommended height off the floor is
a minimum of 70mm. The sides of the panel
heater can be installed within 10mm of a
corner or furniture located against a wall.
Directly under windows is an ideal location.
Minimum clearances (mm)
They can also be installed behind
low furniture with a minimum
50mm clearance.
Legs - with castors.
Available as an option for portable
use. The heater can be easily
moved from room to room.
*RUNNING COSTS: NOBO panel heaters are available in various wattages (sizes) which correspond to the power used when the heater is operating.
To achieve economical running costs they must be sized correctly for the room to be heated, and the thermostat set at 18-20 degrees Celsius.
On initial start-up when the room is cold, the panel heater will heat continuously until the desired comfort temperature is reached. To maintain this
temperature the electronic thermostat will switch the heater on and off and only draw power for 50% of the time, called “Cycling at 50%”.
Electricity is charged in cents per kW per hour. To calculate the hourly running cost after initial warm up, check your latest power bill for the tariff
in cents per kW per hour, determine the size of your panel heater in kW (1,000 watts = 1 kW or kilowatt) and substitute this value in the formula:
Cents per hour running cost after warm up = Cycle rate (50%) x tariff (cents per kW hour) x kW (size of heater).
See the table on the left for approximate hourly running costs for a range of tariffs. Your tariff rate and hourly running costs may be different to the ones stated.
Undersizing (using a lower wattage than recommended by NOBO to heat the area concerned) will result in cycling at a lesser %. In the worst case
this could result in a doubling of hourly running costs.
A L S O AVA I L A B L E F R O M N O B O . . .
T H E P O L O R A N G E O F S P E C I A L I S E D H E AT I N G
AND COOLING PRODUCTS
CUT HERE
COMFORT YOU DESERVE
COMFORT YOU DESERVE
POLO Radiant Ceiling Panel Heaters
POLO Convection Panel Heater
- Perfect for difficult to heat areas – large open
plan areas (inside and out), high ceilings
- Can be wall mounted
- Available in sizes from 900 Watts to 4500 Watts
- Designed in Australia of robust construction
- Convenient, top mounted lockable controls
- Seven year replacement warranty
POLO Stainless Steel Heated
Towel Ladders
POLOCOOL Portable Refrigerated
Air Conditioners
- High quality polished stainless steel
- Concealed wiring
- Available in 2 sizes for small or large
bathrooms / en suites
- Largest cooling capacity on the market (19,000 BTU)
- Cool areas up to 39 m²
- Simple installation and operation
Please talk to your retailer or contact NOBO for more information on these products.
NOBO AUSTRALIA
ABN 80 749 103 558
17 Brett Drive, Carrum Downs, VIC 3201
Free Call 1800 MY NOBO (1800 69 6626)
Fax (03) 9775 1400
www.nobo.com.au
www.polocool.com.au
COMFORT YOU DESERVE
D I S T R I B U T O R S O F N O B O A N D P O L O H E AT I N G A N D C O O L I N G P R O D U C T S
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising