SICK | Comtrol DeviceMaster | Operating instructions | Comtrol DeviceMaster

Comtrol DeviceMaster
O P E R AT I N G I N S T R U C T I O N S
Comtrol DeviceMaster
PC driver for connecting a LMS211/221 Laser
Measurement System via Ethernet interface
Operating Instructions
PC driver for Comtrol DeviceMaster Ethernet
Copyright
Copyright © 2008
SICK AG Waldkirch
Auto Ident, Reute Plant
Nimburger Strasse 11
79276 Reute
Germany
Trademark
Windows 2000TM, XPTM, VistaTM and Internet ExplorerTM are registered trademarks or trademarks of the Microsoft Corporation in the USA and other countries.
AcrobatTM ReaderTM is a trademark of Adobe Systems Incorporated.
Latest manual version
For the latest version of this manual (PDF), see www.sick.com.
2
© SICK AG · Division Auto Ident · Germany · All rights reserved
8012680/0000/2008-07-25
Operating Instructions
Contents
Comtrol DeviceMaster Ethernet
Table of contents
1
2
3
4
5
6
8012680/0000/2008-07-25
Notes on this document ............................................................................................... 4
Purpose...................................................................................................................... 4
Target group .............................................................................................................. 4
Depth of information ................................................................................................. 4
Used symbols ............................................................................................................ 5
Install PortVision Plus ................................................................................................... 6
PortVision Connections to DeviceMaster................................................................... 8
Configure the DeviceMaster IP information .............................................................. 9
Driver installation ........................................................................................................10
Driver configuration.....................................................................................................15
© SICK AG · Division Auto Ident · Germany · All rights reserved
3
Operating Instructions
Figures and Tables
Comtrol DeviceMaster Ethernet
1
Notes on this document
1.1
Purpose
This document instructs technical staff to install the driver of the interface converter Comtrol DeviceMaster Ethernet on PC. The driver is used to connect a SICK laser measuring system LMS211/221 to the PC via Ethernet.
The following types of laser measurement system LMS211/221 have an Ethernet interface:
•
LMS211-S26 (Nr. 1044296)
•
LMS221-S26 (Nr. 1044297)
•
LMS211-S27 (Nr. 1044298)
This document contains the following information:
•
Installation or update of the driver on PC
•
Configuration and test of the interface converter Comtrol DeviceMaster Ethernet
A step-by-step approach is taken for all tasks.
Important
The interface converter Comtrol DeviceMaster Ethernet is named in the following simplified
"Device Master" and the PC driver for the Comtrol DeviceMaster Ethernet is named "driver".
1.2
Target group
The traget group of this document is persons assigned the following tasks:
Tasks
Target group
Installation and configuration of
the driver
Qualified staff, e.g. service technicians or engineers
Table 1-1: Target group
1.3
Depth of information
This document contains all information to install the driver on PC.
Important
Further information about the driver of the Comtrol DeviceMaster Ethernet is available from
SICK AG, Auto Ident division.
On the Internet at www.sick.com.
8012680/0000/2008-07-25
© SICK AG · Division Auto Ident · Germany · All rights reserved
4
Figures and Tables
Operating Instructions
PC driver for Comtrol DeviceMaster Ethernet
1.4
Used symbols
To gain easier access, some information in this dokumentation is emphasised as follows:
NOTICE
Notice!
Indicates a potential risk of damage or impair on the functionality of the field bus module or
the connected device.
WARNING
Warning notice!
A warning noctice indicates real or potential danger. This should protect you against accidents.
The safety symbol next to the warning notice indicates why there is a risk of accident. e.g.
due to electricity. The warning levels (CAUTION, WARNING, DANGER) indicate the seriousness of the risk.
¾
Carefully read and follow the warning notices.
Reference
Italic script denotes a reference to further information.
Important
This important note informs you about specific features.
Explanation
Recommendation
TIPP
COMMUNICATION
An explanation provides background knowledge of technical nature.
A recommendation helps you to carry out tasks correctly.
A tip explains setting options in the SOPAS-ET configuration software.
This type of script denotes a term in the user interface in the SOPAS-ET configuration software.
This symbol denotes a section in which the operation steps with the SOPAS-ET configuration
software are described.
This symbol indicates supplementary technical documentation.
¾
There is a procedure which needs to be carried out. This symbol indicates operational instructions which only contain one operational step or operational steps in warning notices
which do not have to be followed in any particular order.
Operational instructions comprising several steps are denoted using consecutive numbers.
5
© SICK AG · Division Auto Ident · Germany · All rights reserved
8012680/0000/2008-07-25
Operating Instructions
Figures and Tables
Comtrol DeviceMaster Ethernet
2
Install PortVision Plus
This chapter describes the installation of PortVision Plus. The required file is located on the
LMS CD in the directory .. \Ethernet installation\PortVisionV3.02.
Double-click the file pvplus_v3.02.msi.
The pop-up window PortVision Plus Setup appears:
8012680/0000/2008-07-25
1.
Select Next.
2.
To continue with the installation, select Next.
© SICK AG · Division Auto Ident · Germany · All rights reserved
6
Figures and Tables
Operating Instructions
PC driver for Comtrol DeviceMaster Ethernet
7
3.
Accept the license agreement and select Next.
4.
To confirm the installation folder, select Next.
5.
To start with the installation, select Install.
6.
Close the installation with Finish.
You will now have a PortVision Plus icon on the desktop.
© SICK AG · Division Auto Ident · Germany · All rights reserved
8012680/0000/2008-07-25
PortVision Connections to DeviceMaster
Chapter 3
Operating Instructions
PC driver for Comtrol DeviceMaster Ethernet
3
PortVision Connections to DeviceMaster
This chapter describes the connection between PortVision and DeviceMaster.
Explanation
1.
Connect an Ethernet patch cable from the NIC in the PC to the DeviceMaster.
If the DeviceMaster has both an UP and DOWN Ethernet port, connect the patch cable
to the DOWN port.
2.
Start PortVision Plus.
The pop-up window Create Shortcuts appears.
3.
Select No.
There is a problem with the WCOM-Tool once open, it blocks the COM Port.
4.
Select Yes to scan the network.
PortVision Plus opens up.
Important
8
The screenshot shows IP information that does not apply to your network.
5.
Note the IP address.
The IP address must be compatible with the static IP address assigned to the PC.
6.
To communicate directly with the MasterDevice, use Telnet.
© SICK AG · Division Auto Ident · Germany · All rights reserved
8012680/0000/2008-07-25
Operating Instructions
Configure the DeviceMaster IP information
Chapter 4
Comtrol DeviceMaster Ethernet
4
Configure the DeviceMaster IP information
This chapter describes the configuration of the DeviceMaster.
Requirement: PortVision and DeviceMaster are connected.
1.
Double-click on the DeviceMaster.
The pop-up window Configure Device: Device ... appears.
2.
Important
8012680/0000/2008-07-25
Modify the IP address, Subnetz Mask and Gateway address for compatibility with your
network.
The screenshot shows IP information that does not apply to your network.
3.
Select Apply Changes.
4.
Select Close.
The DeviceMaster will now reboot to set the new IP information.
© SICK AG · Division Auto Ident · Germany · All rights reserved
9
Driver installation
Chapter 5
Operating Instructions
PC driver for Comtrol DeviceMaster Ethernet
5
Driver installation
This chapter describes the installation of the driver. The required file is located on the LMS
CD in the directory .. \Ethernet installation\Driver.
10
Important
If installing multiple DeviceMasters, you may repeat the following process once for each DeviceMaster. Once all of the DeviceMaster drivers have been installed you can then go into
DeviceManager to configure the different units. You may also decided to install the driver,
then configure the driver in DeviceManager and then install the next unit, configure, install,
configure, etc. Either method is acceptable.
Important
You may not see all of the following screenshots based on the Operating System that you
are running.
1.
Double-click the file csa_nslink-winxp-1.00.exe.
This will create a default directory at C:\Comtrol and extract its files to this folder.
2.
Go to Control Panel and Add Hardware.
Hardware-Wizard opens up.
3.
Select Next.
© SICK AG · Division Auto Ident · Germany · All rights reserved
8012680/0000/2008-07-25
Operating Instructions
Driver installation
Chapter 5
Comtrol DeviceMaster Ethernet
8012680/0000/2008-07-25
4.
Select Next.
5.
Select Next.
6.
Select Next.
© SICK AG · Division Auto Ident · Germany · All rights reserved
11
Chapter 5
Driver installation
Operating Instructions
PC driver for Comtrol DeviceMaster Ethernet
7.
Select the type of hardware.
8.
Select the Have Disk... option.
9.
Enter the path of C:\Comtrol.
10. Select the correct model type..
12
© SICK AG · Division Auto Ident · Germany · All rights reserved
8012680/0000/2008-07-25
Operating Instructions
Driver installation
Chapter 5
Comtrol DeviceMaster Ethernet
11. Select Next to install the hardware.
12. Select Finish.
Depending on the Windows version, the New Hardware Wizard opens up.
8012680/0000/2008-07-25
© SICK AG · Division Auto Ident · Germany · All rights reserved
13
Chapter 5
Driver installation
Operating Instructions
PC driver for Comtrol DeviceMaster Ethernet
13. Select Next.
14. Select Next.
15. Select Finish.
16. Repeat steps 2–15 to install the driver for further DeviceMaster.
14
© SICK AG · Division Auto Ident · Germany · All rights reserved
8012680/0000/2008-07-25
Operating Instructions
Driver configuration
Chapter 6
Comtrol DeviceMaster Ethernet
6
Driver configuration
This chapter describes the configuration of the driver.
Important
8012680/0000/2008-07-25
In DeviceManager, do not open the properties pages for multiple DeviceMasters at the
same time!
1.
Go to System Properties and System.
2.
Select hardware.
3.
Select DeviceManager.
4.
Expand MultiPortSerial Adapters.
5.
Double-click the DeviceMaster.
The properties pages opens up.
© SICK AG · Division Auto Ident · Germany · All rights reserved
15
Chapter 6
Driver configuration
Operating Instructions
PC driver for Comtrol DeviceMaster Ethernet
16
6.
Go to the Port Settings tab.
7.
Choose COM-Port and select Properties.
The pop-up window COM5 Properties opens up.
8.
Change COM port RS mode to RS422 and select OK.
© SICK AG · Division Auto Ident · Germany · All rights reserved
8012680/0000/2008-07-25
Operating Instructions
Driver configuration
Chapter 6
Comtrol DeviceMaster Ethernet
9.
Go to the Device Settings tab.
10. Set Keep Alive Timeout (seconds): 12.
11. Place a checkmark in the option Do NOT attempt to load firmware to device.
12. Select OK.
The pop-up window Warning appears.
13. Select Yes.
The pop-up window RpshSi appears.
14. Select Yes.
Driver configuration pages will now close.
15. Reopen the properties.
16. Go to the Network Connections tab.
8012680/0000/2008-07-25
© SICK AG · Division Auto Ident · Germany · All rights reserved
17
Chapter 6
Driver configuration
Operating Instructions
PC driver for Comtrol DeviceMaster Ethernet
17. Click the drop down arrow next to the MAC mode and select the appropriate MAC
address.
18. Select OK.
The proerties pages will close.
19. Reopen the properties page
20. Go again to the Network Connections tab.
21. Choose IP Mode and set the correct IP address.
18
© SICK AG · Division Auto Ident · Germany · All rights reserved
8012680/0000/2008-07-25
Operating Instructions
Driver configuration
Chapter 6
Comtrol DeviceMaster Ethernet
22. Choose button Retrieve Network Addresses from the Device.
23. Go to the Advisor tab.
The summary should show Device is active and OK.
24. Select OK and test the DeviceMaster for proper operation.
8012680/0000/2008-07-25
© SICK AG · Division Auto Ident · Germany · All rights reserved
19
8012680/2008-07-xx ∙ 5M/TR <PM6.5/FM7.0/PDF>/VD ∙ Printed in Germany ∙ Subject to change without notice ∙ The specified product features and technical data do not represent any guarantee ∙ 05 Pre int61
Australia
Phone+61 3 9497 4100
1800 33 48 02 – tollfree
E-Mail sales@sick.com.au
Belgium/Luxembourg
Phone +32 (0)2 466 55 66
E-Mail info@sick.be
Brasil
Phone+55 11 3215-4900
E-Mail sac@sick.com.br
Ceská Republika
Phone+420 2 57 91 18 50
E-Mail sick@sick.cz
China
Phone+852-2763 6966
E-Mail ghk@sick.com.hk
Danmark
Phone+45 45 82 64 00
E-Mail sick@sick.dk
Deutschland
Phone+49 211 5301-270
E-Mail info@sick.de
España
Phone+34 93 480 31 00
E-Mail info@sick.es
France
Phone+33 1 64 62 35 00
E-Mail info@sick.fr
Great Britain
Phone+44 (0)1727 831121
E-Mail info@sick.co.uk
India
Phone+91–22–4033 8333
E-Mail info@sick-india.com
Israel
Phone+972-4-999-0590
E-Mail info@sick-sensors.com
Italia
Phone+39 02 27 43 41
E-Mail info@sick.it
Österreich
Phone+43 (0)22 36 62 28 8-0
E-Mail office@sick.at
Polska
Phone+48 22 837 40 50
E-Mail info@sick.pl
Republic of Korea
Phone+82-2 786 6321/4
E-Mail kang@sickkorea.net
Republika Slowenija
Phone+386 (0)1-47 69 990
E-Mail office@sick.si
România
Phone+40 356 171 120
E-Mail office@sick.ro
Russia
Phone+7 495 775 05 34
E-Mail info@sick-automation.ru
Schweiz
Phone+41 41 619 29 39
E-Mail contact@sick.ch
Singapore
Phone+65 6744 3732
E-Mail admin@sicksgp.com.sg
Suomi
Phone+358-9-25 15 800
E-Mail sick@sick.fi
Sverige
Phone+46 10 110 10 00
E-Mail info@sick.se
Taiwan
Phone+886 2 2365-6292
E-Mail sickgrc@ms6.hinet.net
Türkiye
Phone+90 216 587 74 00
E-Mail info@sick.com.tr
USA/Canada/México
Phone+1(952) 941-6780
1 800-325-7425 – tollfree
E-Mail info@sickusa.com
Japan
Phone+81 (0)3 3358 1341
E-Mail support@sick.jp
Nederlands
Phone+31 (0)30 229 25 44
E-Mail info@sick.nl
Norge Phone+47 67 81 50 00
E-Mail austefjord@sick.no
SICK AG | Waldkirch | Germany | www.sick.com
More representatives and agencies
in all major industrial nations at
www.sick.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising