Manual - Biostar
BIPV10-IAP Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction ........................................ 2
1.1
1.2
1.3
1.4
1.5
Before You Start ................................................................................ 2
Package Checklist ............................................................................. 2
Mainboard Specification................................................................... 3
Rear Panel.......................................................................................... 4
Mainboard Layout ............................................................................ 6
Chapter 2: Installation .......................................... 7
2.1
2.2
2.3
2.4
2.5
CPU...................................................................................................... 7
Fan Header......................................................................................... 7
System Memory.................................................................................. 8
Power Supply ..................................................................................... 9
Onboard Slot/Connector/Header/Jumper .................................... 10
Chapter 3: BIOS Setup ........................................ 23
3.1
3.2
3.3
3.4
3.5
3.6
Main Menu........................................................................................ 25
Advanced Menu............................................................................... 28
PCI/PnP Menu.................................................................................. 39
Boot Menu ........................................................................................ 42
Chipset Menu.................................................................................... 44
Exit Menu.......................................................................................... 49
Chapter 4: Useful Help ........................................ 53
4.1
4.2
4.3
Driver Installation Note.................................................................. 53
AMI BIOS Beep Code....................................................................... 54
Troubleshooting............................................................................... 55
Mini-ITX Mainboard Manual
CHAPTER 1: INTRODUCTION
1.1
BEFORE YOU START
Thank you for choosing our product. Before you start installing the
mainboard, please make sure you follow the instructions below:
„ Prepare a dry and stable working environment with
sufficient lighting.
„ Always disconnect the system from power outlet
before operation.
„ Before you take the mainboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
„ Avoid touching the components on mainboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
„ Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
„ Keep the system from dangerous area, such as heat
source, humid air, and water.
„
1.2
Please switch on/off the machine normally. That is, DO
NOT pull out power cord directly from the mainboard
or the system may damage.
PACKAGE CHECKLIST
Mini-ITX Mainboard x 1
Fully Setup Driver CD x 1
I/O Bracket x 1
SATA Cable x 1 (Optional)
2
BIPV10-IAP
1.3
MAINBOARD SPECIFICATION
Specification
Optional for:
Intel Atom CPU On-board
CPU
D425 @1.8GHz
N455 @1.66GHz (TDP 6.5W)
(TDP 10W)
N550 dual core @1.5GHz (TDP 8.5W)
Pineview-D Processor
FSB
Supports up 800 MHz
Chipset
Intel NM10 Express Chipset
D525 dual core @ 1.8GHz (TDP 13W)
Max Shared Video Memory is 384 MB
--LVDS by CH7036 (24 bit single CH,
Graphic
Intel Pineview-D integrated graphics engine support up to 1366x768)
--Integrated VGA scale up to SXGA+
1400x1050)
128pin type
ITE IT8728 + FINTEK F81216D
Super I/O Provides the most commonly used legacy
Super I/O functionality.
SO-DIMM (204pin) Slot x 1
Registered DIMM or ECC DIMM is not
Supports DDR3 800 MHz
Memory
DIMM supports 512MB / 1GB / 2GB / 4GB
Max Memory Capacity 4GB
Chipset built-in Serial ATA controller
LAN
Realtek RTL 8111E
Sound
Codec
Amplifier
On Board
* N455/N550 only support up to 2GB
Data transfer rates up to 3.0 Gb/s
10 / 100 / 1000 Mb/s auto negotiation
Half / Full duplex capability
5.1 channels audio out (only for x3 audio
jack version)
High-Definition Audio support
Realtek ALC105
Class D, 2 channel Max. 2.8W
x1
PCI Express x1 Slot
x1
Mini PCI-E Slot
x1
SATA2 Connector
x2
Connectors Power Connector for SATA
& Headers
supported
SATA Version 2.0 specification compliant
Realtek ALC662
PCI slot
Slot
H/W Monitor
Fan Speed Controller
Main
SATA
Environment Control initiat ives,
x1
Front Panel Header
x1
Parallel Connector
x1
Digital I/O Connector
x1
System Fan Header
x2
Clear CMOS Header
x1
3
Mini-ITX Mainboard Manual
Specification
Speaker Box Connector
x1
Amplifier Connector
x2
PS/2 Keyboard/Mouse Connector
x1
AT/ATX Power Switch Header
x1
USB 2.0 Connector
x1
LVDS Connector
x1
LCD Power Select Header
x1
LCD Backlight Power ON/OFF Header x1
LCD Backlight Inverter Connector
x1
Inverter Power Select Header
x1
Backlight Brightness Adjust Header
x1
Serial Connectors (RS-232)
x3
Power Connector (4pin)
x1
DC Jack
x1
RJ-11 Port
x1
PS/2 Keyboard
x1
Back Panel Serial Port
I/O
for cash drawer
x3
VGA Port
x1
RJ-45 Port
x1
USB2.0 Port
x4
Audio Jack (Line-out/Mic)
x2
Optional for x3 (Line-in/Line-out/Mic)
Board Size 170 mm (W) x 170 mm (L)
Mini-ITX
OS
Biostar reserves the right to add or remove
Support
1.4
Windows XP/XPE, Linux
support for any OS with or without notice.
REAR PANEL
CO M3
P S /2
K e y bo a rd
R J -4 5
JC O M1B
L in e O u t
(F ron t)
M ic In
(C enter/SU B)
DC
4
R J -11
V GA
U SB 2.0 x 2 US B 2.0 x 2
JC O M1A
BIPV10-IAP
(1) DC 12V-in pin define
Pin 1
Pin 4
Pin 2
Pin
Assignment
1
+12V DC_In
2
GND
3
GND
4
+12V DC_IN
Pin 3
(2) RJ-11 pin define (Pin #1 ~6 from right to left)
Pin 6
Pin 1
Ver. 1.0
Pin
Define
Status Pin
Control Pin
GPIO
ADD
1
CASE OPEN#2
CASE OPEN#2
---
63
A25H (bit3)
2
CASH1 _P
---
CASH1 _P
40
A23H (bit0)
3
CASE OPEN#
CASE OPEN#
---
36
A22H (bit6)
4
CASH_PWR
---
---
---
---
5
CASH2_P
---
CASH2_P
47
A23H (bit7)
6
GND
---
---
---
---
Ver. 1.2
Pin
Define
Status Pin
Control Pin
GPIO
ADD.
1
CASE OPEN#2
CASE OPEN#2
---
63
A25H (bit3)
2
CASH1 _P
---
CASH1 _P
14
A20H (bit4)
3
CASE OPEN#
CASE OPEN#
---
64
A25H (bit4)
4
CASH_PWR
---
---
---
---
5
CASH2_P
---
CASH2_P
47
A23H (bit7)
6
GND
---
---
---
---
5
Mini-ITX Mainboard Manual
MAINBOARD LAYOUT
BAT1
JP 9
JCOM 5
JP1
JP WR1
JPC4
JPC5
JPC6
CN1
JSFA N1
1.5
JCO M4 JCOM 6
D IMMA 1
JC1
LVDS -OUT 1
JBL1
US B_
KB MS1
JKBMS1
JRJ45US B1
JBL2
Intel
Atom
CPU
CPU1
SATA2
SATA1
JPR NT1
JC O M1
JP C1
JP C2
NM10
JDIO 1
B
A
JSFAN2
PE1
BIOS
JSPK3
JAU DIO2
JS PK2
JC MOS 1
JAT 1
JPA NEL1
PCI1
JS PK1
Note: ■ represents the 1st pin.
6
JU SB1
J HDD 1
JVGA1
JPC3
JLV2
JLV1
PE X1
BIPV10-IAP
CHAPTER 2: INSTALLATION
2.1
CPU
The mainboard includes an embedded Intel Atom N455/N550/D525/D425
processor, and a heatsink has been installed to provide sufficient cooling.
2.2
FAN HEADER
The fan header supports cooling-fans built in the system. The fan cable
and connector may be different due to the fan manufacturer.
JSFAN1: System Fan Header
3
Pin
1
2
1
3
Assignment
Ground
+12V Smart
Fan Control (By
Fan)
FAN RPM rate
sense
JSFAN2: System Fan Header
Pin
1
2
3
1
Assignment
Ground
+12V
FAN RPM rate
sense
3
Note:
System Fan Headers support 3-pin head connectors. When connecting with wires onto
connectors, please note that the red wire is the positive and should be connected to
pin#2, and the black wire is Ground and should be connected to GND.
7
Mini-ITX Mainboard Manual
2.3
SYSTEM MEMORY
DIMMA1: Memory Module (204pin SO-DIMM)
2
Align a DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
3
Insert the DIMM firmly into the slot until the retaining chip snap back in
place and the DIMM is properly seated.
Memory Capacity
8
DIMM Socket Location
DDR3 Module
Total Memory Size
DIMMA1
512MB / 1GB / 2GB / 4GB
Max is 4GB.
BIPV10-IAP
2.4
POWER SUPPLY
JPWR1: ATX Power Source Connector (4-pin)
This connector provides +12V to system power circuit.
4
3
1
2
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
JHDD1: SATA Power Connector
This connector provides power connection of SATA devices.
Pin
1
Assignment
1
+12V
2
GND
3
+3.3V
4
+5V
4
9
Mini-ITX Mainboard Manual
2.5
ONBOARD SLOT/CONNECTOR/HEADER/JUMPER
PCI1: Peripheral Component Interconnect Slot
This mainboard is equipped with 1 standard PCI slot. PCI stands for Peripheral
Component Interconnect, and it is a bus standard for expansion cards. This PCI
slot is designated as 32 bits.
PCI1
PE1: Mini PCI-E Slot
This mainboard is equipped with 1 Mini PCI-E Slot.
10
BIPV10-IAP
PEX1: PCI-Express x1 Slot
-
PCI-Express 1.1 compliant.
Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.
PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
SATA1/SATA2: Serial ATA Connectors
These next generation connectors support the thin Serial ATA cable for primary
internal storage devices. The current Serial ATA interface allows up to 3.0
Gbit/s data transfer rate.
Pin
SA TA2
SATA 1
7
4
1
Assignment
1
GND
2
TX+
3
TX-
4
GND
5
RX-
6
RX+
7
GND
11
Mini-ITX Mainboard Manual
JUSB1: USB 2.0 Connector
The mainboard provides 1 front USB pin connector, allowing up to 2 additional
USB 2.0 ports up to maximum throughput of 480 Mbps. Connect the USB
cable into the pin header for using high-speed USB interface peripherals.
2
10
1
9
Pin
Assignment
Pin
Assignment
1
+5V (fused)
2
+5V (fused)
3
USB5-
4
USB7-
5
USB5+
6
USB7+
7
Ground
8
Ground
9
Key
10
NC
JPANEL1: Front Panel Header
This 10-pin header includes Power-on, Reset, HDD LED, and Power LED
connection. It allows user to connect the system case’s front panel switch
functions.
Pin
Assignment
Function
1
Key
N/A
3
HD LED+
5
HD LED-
7
Reset GND
9
12
Reset
HDD LED
Reset Button
Pin
Assignment
2
Power LED+
4
Power LED+
6
Power LED-
8
Power
10
Power GND
2
10
1
9
Function
Power LED
Power Button
BIPV10-IAP
JDIO1: Digital I/O Connector
This connector offers 4-pair of digital I/O functions and address is set in BIOS.
The default address is:
z
DI01 -> 48CH BIT6-> GPIO6
z
DI02 -> 48CH BIT7-> GPIO7
z
DI03 -> 48DH BIT0-> GPIO8
z
DI04 -> 48DH BIT1-> GPIO9
z
DO01 -> 48DH BIT2-> GPIO10
z
DO02 -> 48DH BIT5-> GPIO13
z
DO03 -> 48DH BIT6-> GPIO14
z
DO04 -> 48DH BIT7-> GPIO15
Pin
9
10
1
2
Assignment
1
5V
2
Digital-In-6
3
Digital-Out-10
4
Digital-In-7
5
Digital-Out-13
6
Digital-In-8
7
Digital-Out-14
8
Digital-In-9
9
Digital-Out-15
10
GND
JKBMS1: Keyboard/Mouse Connector
The mainboard provides a PS2 pin header to attach a PS2 keyboard/mouse.
Pin
6
1
Assignment
6
JUSBLAN1_POWER
5
GND
4
KB_DATA
3
KB_CLK
2
MS_DATA
1
MS_CLK
13
Mini-ITX Mainboard Manual
JCMOS1: Clear CMOS Header *
Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
mainboard.
1
3
Pin 1-2 Close: (Default)
Normal Operation.
3
1
Pin 2-3 Close:
Clear CMOS data.
1
3
※ Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.
JAT1: AT/ATX Power Switch Header *
This header is for switching between AT and ATX power.
1
3
Pin 1-2 Close:
For AT Power
3
1
Pin 2-3 Close: (Default)
For ATX Power
1
14
3
BIPV10-IAP
JCOM1A/JCOM1B/JCOM3: Serial Port Connectors
The motherboard has 3 Serial Port Connectors for connecting RS-232 Port.
JCOM3
JC O M 1 B
JC O M 1 A
Pin
Assignment
1
Carrier detect (DCD)
2
Received data (RXD)
3
Transmitted data (TXD)
4
Data terminal ready (DTR)
5
Signal ground (GND)
6
Data set ready (DSR)
7
Request to send (RTS)
8
Clear to send (CTS)
9
Ring or 5V or 12V (JCOM1A)
Ring or 5V (JCOM1B/JCOM3)
* Do not support RI wake up
JCOM4/JCOM5/JCOM6: Serial Port Connectors
The motherboard has 4 Serial Port Connectors for connecting RS-232 Port.
JCO M 4 JCO M 6
JCO M 5
10
9
2
1
Pin
Assignment
1
2
3
4
5
6
7
8
9
10
-PDCD
PSIN
PSOUT data
-PDTR
GND
-PDSR
-PRTS
-PCTS
-PRI
5V or 12V
15
Mini-ITX Mainboard Manual
JPC1: Voltage Switch Header for JCOM1A
This header is for controlling the Pin 9 of JCOM1A to switch Ring, 5V, or 12V.
2
1
Pin 1-2 Close:
Pin9=Ring (Default)
4
2
6
1
5
3
Pin 2-3 Close:
Pin9=5V
6
5
Pin 2-3 Close:
Pin9=12V
JPC2: Voltage Switch Header for JCOM1B
This header is for controlling the Pin9 of JCOM1B to switch Ring or 5V.
1
3
Pin 1-2 Close:
Pin9=5V
1
3
3
1
Pin 2-3 Close:
Pin9=Ring (Default)
JPC3: Voltage Switch Header for JCOM3
This header is for controlling the Pin9 of JCOM3 to switch Ring or 5V.
1
3
1
3
Pin 1-2 Close:
Pin9=5V
3
1
Pin 2-3 Close:
Pin9=Ring (Default)
16
BIPV10-IAP
JPC4: Voltage Switch Header for JCOM4
This header is for controlling the Pin10 of JCOM4 to switch Ring or 5V.
1
3
1
3
Pin 1-2 Close:
Pin10=5V (Default)
3
1
Pin 2-3 Close:
Pin10=12V
JPC5: Voltage Switch Header for JCOM5
This header is for controlling the Pin10 of JCOM5 to switch Ring or 5V.
1
3
1
3
Pin 1-2 Close:
Pin10=5V (Default)
3
1
Pin 2-3 Close:
Pin10=12V
JPC6: Voltage Switch Header for JCOM6
This header is for controlling the Pin10 of JCOM6 to switch Ring or 5V.
1
3
1
3
Pin 1-2 Close:
Pin10=5V (Default)
3
1
Pin 2-3 Close:
Pin10=12V
17
Mini-ITX Mainboard Manual
JP1: Voltage Switch Header for Cash Draw Connector (CN1)
This header is for controlling the Pin4 of CN1 to switch 12V or 24V.
1
3
1
3
Pin 1-2 Close:
CN1=24V (Default)
3
1
Pin 2-3 Close:
CN1=12V
JSPK1/JSPK2: Amplifier Connectors
The mainboard provides 2 amplifier connectors.
JSPK1
Pin
Assignment
1
SPKRN
2
SPKRP
JSPK2
J SPK2 JSPK1
Pin
Assignment
1
SPKLN
2
SPKLP
2 1
JSPK3: Speaker Box Connector
The mainboard provides a speaker box connector.
Pin
4
1
18
Assignment
1
LINEOUTL
2
GND_AUD
3
GND_AUD
4
LINEOUTR
BIPV10-IAP
LVDS-CONN1: LVDS Connector
This connector is for devices requiring display interface such as LVDS.
This connector supports 18/24 bit single-channel panels up to 1366 x 768
„ It is strongly recommended to use the matching JOY DAY INDUSTRIAL A1252WV-SF-2X20PD01 connector.
Pin
Assignment
39
40
1
2
Pin
Assignment
1
NC
2
PVDD (+3.3V or +5V or +12V)
3
NC
4
PVDD (+3.3V or +5V or +12V)
5
GND
6
GND
7
NC
8
GND
LVDS1_TX0- (Differential signal)
9
NC
10
11
GND
12
LVDS1_TX0+ (Differential signal)
13
NC
14
GND
15
NC
16
LVDS1_TX1- ( (Differential signal)
17
GND
18
LVDS1_TX1+ (Differential signal)
19
NC
20
GND
21
NC
22
LVDS1_TX2- (Differential signal)
23
GND
24
LVDS1_TX2+(Differential signal)
25
NC
26
GND
27
NC
28
LVDS1_CLK- (Differential signal)
29
+5V
30
LVDS1_CLK+(Differential signal)
31
I2C_CLK
32
GND
33
+3.3V
34
LVDS1_TX3-(Differential signal)
35
NC
36
LVDS1_TX3+(Differential signal)
37
PVDD (+3.3V or +5V)
38
GND
39
PVDD (+3.3V or +5V)
40
I2C_DATA
19
Mini-ITX Mainboard Manual
JLV1: LCD Power Select Header
This header allows you to select LCD Power.
1
3
1
3
Pin 1-2 Close:
Inverter Power=5V
(Default)
3
1
Pin 2-3 Close:
Inverter Power=3.3V
JLV2: LCD Backlight Inverter Power Select Header *
This header is for selecting LCD Backlight Inverter Power.
1
3
Pin 1-2 Close:
Inverter Power=5V
1
3
3
1
Pin 2-3 Close:
Inverter Power=12V
(Default)
JBL1: LCD Backlight Power ON/OFF Header *
This header allows you to control the LCD Backlight Power ON/OFF.
1
2
1
Header Close:
Backlight Power OFF
1
Header Open:
Backlight Power ON
20
BIPV10-IAP
JBL2: LCD Backlight Brightness Adjust Header *
This header is for adjusting LCD backlight brightness.
4
2
4
2
3
1
3
1
Short Pin 1-2:
Increase Brightness
4
2
3
1
Short Pin 3-4:
Decrease Brightness
JC1: LCD Backlight Inverter Connector
This connector is for connecting to LCD for providing backlight control function.
It is strongly recommended to use the matching JOY DAY INDUSTRIAL
- A1250WV-S-8P connector.
Pin
Assignment
1
5V/12V DC
2
5V/12V DC
3
NC
4
NC
5
Backlight On
6
Brightness Adjust
7
GND
8
GND
21
Mini-ITX Mainboard Manual
JPRNT1: Printer Port Connector
This header allows you to connect printer port on the PC.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5
Pin
14
15
16
17
18
19
20
21
22
23
24
25
26
2
26
1
25
Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key
*How to Setup Jumpers
The illustration shows how to set up jumpers. When the jumper cap is placed on
pins, the jumper is “close”, if not, that means the jumper is “open”.
Pin opened
22
Pin closed
Pin1-2 closed
BIPV10-IAP
CHAPTER 3: BIOS SETUP
Introduction
The purpose of this chapter is to describe the settings in the AMI BIOS Setup
program on this motherboard. The Setup program allows users to modify the basic
system configuration and save these settings to CMOS RAM. The power of CMOS
RAM is supplied by a battery so that it retains the Setup information when the
power is turned off.
Basic Input-Output System (BIOS) determines what a computer can do without
accessing programs from a disk. This system controls most of the input and output
devices such as keyboard, mouse, serial ports and disk drives. BIOS activates at the
first stage of the booting process, loading and executing the operating system. Some
additional features, such as virus and password protection or chipset fine-tuning
options are also included in BIOS.
The rest of this manual will to guide you through the options and settings in BIOS
Setup.
Plug and Play Support
This AMI BIOS supports the Plug and Play Version 1.0A specification.
EPA Green PC Support
This AMI BIOS supports Version 1.03 of the EPA Green PC specification.
ACPI Support
AMI ACPI BIOS support Version 1.0/2.0 of Advanced Configuration and Power
interface specification (ACPI). It provides ASL code for power management and
device configuration capabilities as defined in the ACPI specification, developed by
Microsoft, Intel and Toshiba.
23
Mini-ITX Mainboard Manual
PCI Bus Support
This AMI BIOS also supports Version 2.3 of the Intel PCI (Peripheral Component
Interconnect) local bus specification.
DRAM Support
DDR2 SDRAM (Double Data Rate II Synchronous DRAM) is supported.
Supported CPUs
This AMI BIOS supports the Intel CPU.
Using Setup
When starting up the computer, press <Del>
during the Power-On Self-Test (POST) to enter
the BIOS setup utility.
In the BIOS setup utility, you will see General
Help description at the top right corner, and this
is providing a brief description of the selected
item. Navigation Keys for that particular
menu are at the bottom right corner, and you can
use these keys to select item and change the
settings.
Gene ral Help
Navigation Keys
Notice
z
z
z
24
The default BIOS settings apply for most conditions to ensure optimum
performance of the motherboard. If the system becomes unstable after
changing any settings, please load the default settings to ensure system’s
compatibility and stability. Use Load Setup Default under the Exit Menu.
For better system performance, the BIOS firmware is being continuously updated.
The BIOS information described in this manual is for your reference only.
The actual BIOS information and settings on board may be slightly different
from this manual.
The content of this manual is subject to be changed without notice. We will not
be responsible for any mistakes found in this user’s manual and any system
damage that may be caused by wrong-settings.
BIPV10-IAP
3.1
MAIN MENU
Once you enter AMI BIOS Setup Utility, the Main Menu will appear on the screen
providing an overview of the basic system information.
Main
Advanced
PCIPnP
BIOS SETUP UTILITY
Boot
Chipset
Use [ENTER], [TAB]
or [SHIFT-TAB] to
select a field.
System Overview
AMI BIOS
Version
:01.01.01
Build Date:01/01/10
System Memory
Size
:
System Time
System Date
> IDE Configuration
Exit
Use [+] or [-] to
configure system Time.
[ 00:00:00]
[Fri 01/01/2010]
+Tab
F1
F10
ESC
Select Screen
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
AMI BIOS
Shows system information including BIOS version, built date, etc.
System Memory
Shows system memory size, VGA shard memory will be excluded..
System Time
Set the system internal clock.
System Date
Set the system date. Note that the ‘Day’ automatically changes when you set the
date.
25
Mini-ITX Mainboard Manual
IDE Configuration
The BIOS will automatically detect the presence of IDE/SATA devices. There is a
sub-menu for each IDE/SATA device. Select a device and press <Enter> to enter
the sub-menu of detailed options.
BIOS SETUP UTILITY
Main
IDE Confuguration
Configure SATA as
Options
[IDE]
> SATA 1
> SATA 2
Hard Disk Write Protect
IDE Detect Time Out (Sec)
IDE
AHCI
Disabled
[Disabled]
[35]
Select Screen
Select Item
Enter Go to Sub Screen
General Help
F1
F10 Save and Exit
ESC Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Configure SATA as
This item allows you to determine the control mode of SATA.
Options: IDE (Default) / AHCI / Disabled
SATA 1/2 Devices
BIOS SETUP UTILITY
Main
SATA 1 Device
Device
:
Select the type
of device connected
to the system.
Type
[Auto]
LBA/Large Mode
[Auto]
Block (Multi-Sector Transfer)[Auto]
PIO Mode
[Auto]
DMA Mode
[Auto]
S.M.A.R.T
[Auto]
32Bit Data Transfer
[Enabled]
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
26
BIPV10-IAP
The BIOS detects the information and values of respective devices, and these
information and values are shown below to the name of the sub-menu.
Type
Select the type of the SATA drive.
Options: Auto (Default) / CD/DVD / ARMD / Not Installed
LBA/Large Mode
Enable or disable the LBA mode.
Options: Auto (Default) / Disabled
Block (Multi-Sector Transfer)
Enable or disable multi-sector transfer.
Options: Auto (Default) / Disabled
PIO Mode
Select the PIO mode.
Options: Auto (Default) / 0 / 1 / 2 / 3 / 4
DMA Mode
Select the DMA mode.
Options: Auto (Default) / SWDMA0 ~ SWDMA2 / MWDMA0 ~ MWDMA2 /
UDMA0 ~ UDMA5
S.M.A.R.T
Set the Smart Monitoring, Analysis, and Reporting Technology.
Options: Auto (Default) / Disabled / Enabled
32Bit Data Transfer
Enable or disable 32-bit data transfer.
Options: Enabled (Default) / Disabled
Hard Disk Write Protect
Disable or enable device write protection.
is accessed through BIOS.
Options: Disabled (Default) / Enabled
This will be effective only if the device
IDE Detect Time Out (Sec)
Select the time out value for detecting IDE/SATA devices.
Options: 35 (Default) / 30 / 25 / 20 / 15 / 10 / 5 / 0
27
Mini-ITX Mainboard Manual
3.2
ADVANCED MENU
The Advanced Menu allows you to configure the settings of CPU, Super I/O, Power
Management, and other system devices.
Notice
z
Beware of that setting inappropriate values in items of this menu may cause
system to malfunction.
Main
Advanced
PCIPnP
BIOS SETUP UTILITY
Boot
Chipset
Advanced Settings
Exit
Configure CPU.
WARNING: Setting wrong values in below sections
may cause system to malfunction.
>
>
>
>
>
>
CPU Configuration
SuperIO Configuration
Hardware Health Configuration
Smart Fan Configuration
ACPI Configuration
USB Configuration
Select Screen
Select Item
Enter Go to Sub Screen
F1
General Help
F10 Save and Exit
ESC Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
CPU Configuration
This item shows the CPU information that the BIOS automatically detects.
Advanced
BIOS SETUP UTILITY
Configure advanced CPU settings
Module Version:3F.1C
Disabled for WindowsXP
Manufacturer:Intel
Frequency
:
FSB Speed
:
Cache L1
:
Cache L2
:
Ratio Actual Value:
Max CPUID Value Limit
[Disabled]
Execute-Disable Bit Capability[Enabled]
Hyper Threading Technology
[Enabled]
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
28
BIPV10-IAP
Max CPUID Value Limit
When the computer is booted up, the operating system executes the CPUID
instruction to identify the processor and its capabilities. Before it can do so, it must
first query the processor to find out the highest input value CPUID recognizes. This
determines the kind of basic information CPUID can provide the operating system.
Options: Disabled (Default) / Enabled
Execute-Disable Bit Capability
This item allows you to configure the Execute Disabled Bit function, which protects
your system from buffer overflow attacks.
Options: Enabled (Default) / Disabled
Hyper Threading Technology
Enabled for Windows XP and Linux (OS optimized for Hyper Threading
Technology) and disabled for other OS (OS not optimized for Hyper Threading
Technology).
Options: Enabled (Default) / Disabled
SuperIO Configuration
Advanced
BIOS SETUP UTILITY
Configure ITE8718 Super IO Chipset
Serial Port1 Address
Serial Port2 Address
Parallel Port Address
Parallel Port Mode
Parallel Port IRQ
Second IO UART IRQ MODE
Serial Port 3-6 IRQ Share
Serial Port3 Address
Serial Port4 Address
Serial Port5 Address
Serial Port6 Address
Watch Dog Degree
Watch Dog Timer
[3F8/IRQ4]
[2F8/IRQ3]
[378]
[Normal]
[IRQ7]
[PCI IRQ Sharing]
[IRQ5]
[3E8]
[2E8]
[2F0]
[2E0]
[Second]
[00000]
Allows BIOS to Select
Serial Port1 Base
Addresses.
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Serial Port1 Address
Select an address and corresponding interrupt for Serial Port 1.
Options: 3F8/IRQ4 (Default) / 3E8/IRQ4 / 2E8/IRQ3 / Disabled
29
Mini-ITX Mainboard Manual
Serial Port2 Address
Select an address and corresponding interrupt for Serial Port 2.
Options: 2F8/IRQ3 (Default) / 3E8/IRQ4 / 2E8/IRQ3 / Disabled
Parallel Port Address
This item allows you to determine access onboard parallel port controller with
which I/O Address.
Options: 378 (Default) / 278 / 3BC / Disabled
Parallel Port Mode
This item allows you to determine how the parallel port should function.
Options: Normal (Default)
Using Parallel port as Standard Printer Port.
EPP
Using Parallel Port as Enhanced Parallel Port.
ECP
Using Parallel port as Extended Capabilities Port.
ECP+EPP
Using Parallel port as ECP & EPP mode.
ECP Mode DMA Channel
This item allows you to select parallel port ECP DMA.
Options: DMA3 (Default) / DMA0 / DMA1
Parallel Port IRQ
This item allows you to select the IRQ for the onboard parallel port.
Options: IRQ7 (Default) / IRQ5
Second IO UART IRQ MOde
PCI IRQ Sharing for OS (EX. WinXP); ISA IRQ Sharing for Dos.
Options: PCI IRQ Sharing (Default) / ISA IRQ
Serial Port 3-6 IRQ Share
This item allows you to determine whether Serial Port 3-6 share IRQ.
Options: IRQ5 (Default) / Disabled / IRQ3 / IRQ4 / IRQ7 / IRQ9 / IRQ10 / IRQ11 /
IRQ12
30
BIPV10-IAP
Serial Port3 Address
This item allows you to select the address of Serial Port3.
Options: 3E8 (Default) / 2E8 / 2F0 / 2E0
Serial Port3 IRQ
This item allows you to select IRQ of Serial Port3.
Options: IRQ5 (Default) / IRQ3 / IRQ4 / IRQ7 / IRQ9 / IRQ10 / IRQ11 / IRQ12
Serial Port4 Address
This item allows you to select the address of Serial Port4.
Options: 2E8 (Default) / 3E8 / 2F0 / 2E0
Serial Port4 IRQ
This item allows you to select IRQ of Serial Port4.
Options: IRQ5 (Default) / IRQ3 / IRQ4 / IRQ7 / IRQ9 / IRQ10 / IRQ11 / IRQ12
Serial Port5 Address
This item allows you to select the address of Serial Port5.
Options: 2F0 (Default) / 3E8 / 2E8 / 2E0
Serial Port5 IRQ
This item allows you to select IRQ of Serial Port5.
Options: IRQ5 (Default) / IRQ3 / IRQ4 / IRQ7 / IRQ9 / IRQ10 / IRQ11 / IRQ12
Serial Port6 Address
This item allows you to select the address of Serial Port6.
Options: 2E0 (Default) / 3E8 / 2E8 / 2F0
Serial Port6 IRQ
This item allows you to select IRQ of Serial Port6.
Options: IRQ5 (Default) / IRQ3 / IRQ4 / IRQ7 / IRQ9 / IRQ10 / IRQ11 / IRQ12
31
Mini-ITX Mainboard Manual
Watch Dog Degree
This item allows you to determine the functional degree of Watch Dog.
Options: Second (Default) / Minute
Watch Dog Timer
Options: 0 for disabled (Default) / Min=1, Max=65536
Hardware Health Configuration
This item shows the system temperature, fan speed, and voltage information.
Advanced
BIOS SETUP UTILITY
Hardware Health Configuration
H/W Health Function
Shutdown Temperature
[Enabled]
[Disabled]
Enables Hardware
Health Monitoring
Device.
CPU Temperature
SYSTEM Temperature
JSFan1 Speed
CPU VCore
SB Voltage
+3.30V
+5.00V
+12.0V
GMCH VCore
Memory Voltage
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
H/W Health Function
If with a monitoring system, PC will show PC health status during POST stage.
Options: Enabled (Default) / Disabled
Shutdown Temperature Function
This item allows you to set up the CPU shutdown Temperature. This item is only
effective under Windows 98 ACPI mode.
Options: Disabled (Default) / 60℃/140℉ / 65℃/149℉ / 70℃/158℉ / 75℃/167℉
/ 80℃/176℉ / 85℃/185℉ / 90℃/194℉
32
BIPV10-IAP
Smart Fan Configuration
Advanced
BIOS SETUP UTILITY
Smart Fan Configuration
JSFAN1 Smart Fan
Smart Fan Calibration
Control Mode
o
Fan Ctrl OFF( C)
o
Fan Ctrl On( C)
Fan Ctrl Start value
Fan Ctrl Sensitive
[Disabled]
When you choice [Auto]
,[3Pin] or [4Pin],
please run the
calibration to define
the Fan parameters for
Smart Fan control
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
JSFAN1 Smart Fan
This item allows you to control the JSFAN1 Smart Fan function.
Options: Disabled (Default) / Auto
Smart Fan Calibration
Choose this item and then the BIOS will auto test and detect the CPU fan functions
and show CPU fan speed.
Control Mode
This item provides several operation modes of the fan.
Options: Manual (Default) / Quiet / Performance
Fan Ctrl OFF(℃)
If the CPU Temperature is lower than the set value, the fan will turn off.
Options: 0~127 (℃) (With the interval of 1℃)
Fan Ctrl On(℃)
CPU fan starts to work when the temperature arrives this set value.
Options: 0~127 (℃) (With the interval of 1℃)
33
Mini-ITX Mainboard Manual
Fan Ctrl Start Value
When CPU temperature arrives to the set value, the CPU/System fan will work
under Smart Fan Function mode.
Options: 0~127 (With the interval of 1)
Fan Ctrl Sensitive
Increasing the value of slope PWM will raise the speed of CPU fan.
Options: 0~127 (With the interval of 1)
ACPI Configuration
Advanced
BIOS SETUP UTILITY
ACPI Settings
Power Supply Emulate Mode:
> Advanced ACPI Configuration
> Chipset ACPI Configuration
Resume On RTC Alarm
Resume On PME#
Restore on AC Power Loss by IO
[ ATX ]
[Disabled]
[Disabled]
[Powre Off]
Advanced ACPI
Configuration settings
Use this section to
configure additional
ACPI options.
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
34
BIPV10-IAP
Advanced ACPI Configuration
Advanced
BIOS SETUP UTILITY
Advanced ACPI Configuration
ACPI Version Features
ACPI APIC support
AMI OEMB table
Headless mode
[ACPI v1.0]
[Enabled]
[Enabled]
[Disabled]
Enable RSDP pointers
to 64-bit Fixed System
Description Tables.
ACPI version has some
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
ACPI Version Features
The item allows you to select the version of ACPI.
Options: ACPI v1.0 (Default) / ACPI v2.0 / ACPI v3.0
ACPI APIC support
This item is used to enable or disable the motherboard's APIC (Advanced
Programmable Interrupt Controller). The APIC provides multiprocessor support,
more IRQs and faster interrupt handling.
Options: Enabled (Default) / Disabled
AMI OEMB table
Set this value to allow the ACPI BIOS to add a pointer to an OEMB table in the
Root System Description Table (RSDT) table.
Options: Enabled (Default) / Disabled
Headless mode
This is a server-specific feature. A headless server is one that operates without a
keyboard, monitor or mouse. To run in headless mode, both BIOS and operating
system (e.g. Windows Server 2003) must support headless operation.
Options: Disabled (Default) / Enabled
35
Mini-ITX Mainboard Manual
Chipset ACPI Configuration
Advanced
BIOS SETUP UTILITY
South Bridge ACPI Configuration
Energy Lake Feature
APIC ACPI SCI IRQ
High Performance Event Timer
HPET Memory Address
[Disabled]
[Disabled]
[Disabled]
[FED00000h]
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Energy Lake Feature
This item allows you to enable or disable the Energy Lake technology feature.
Options: Disabled (Default) / Enabled
APIC ACPI SCI IRQ support
This item is used to set APIC ACPI SCI by IRQ.
Options: Disabled (Default) / Enabled
High Performance Event Timer
This item allows you to enable or disabled the HPET.
Options: Enabled (Default) / Disabled
HPET Memory Address
Options: FED00000h (Default) / FED01000h / FED02000h / FED03000h
Resume On RTC Alarm
When “Enabled”, you can set the date and time at which the RTC (real-time clock)
alarm awakens the system from Suspend mode.
Options: Disabled (Default) / Enabled
RTC Alarm Date (Days)
You can choose which date the system will boot up.
36
BIPV10-IAP
RTC Alarm Time
You can choose the system boot up time, input hour, minute and second to specify.
Resume On PME#
This item allows you to disable or enable PME to generate a wake event.
Options: Disabled (Default) / Enabled
Restore on AC Power Loss by IO
This setting specifies how your system should behave after a power fail or interrupts
occurs. By choosing Disabled will leave the computer in the power off state.
Choosing Enabled will restore the system to the status before power failure or
interrupt occurs.
Options: Power Off (Default) / Power ON / Last State
USB Configuration
This item shows the USB controller and using USB device information.
Advanced
BIOS SETUP UTILITY
USB Configuration
Enables support for
legacy USB. AUTO
option disables
legacy support if
no USB devices are
connected.
Module Version - 2.24.5-14.4
USB Devices Enabled:
Legacy USB Support
USB 2.0 Controller Mode
BIOS EHCI Hand-Off
[Enabled]
[HiSpeed]
[Enabled]
> USB Mass Storage Device Configuration
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Legacy USB Support
This item determines if the BIOS should provide legacy support for USB devices
like the keyboard, mouse, and USB drive. This feature is useful for using USB
devices with operating systems that do not natively support USB (e.g. Microsoft
MS-DOS or Windows NT).
Options: Enabled (Default) / Disabled / Auto
37
Mini-ITX Mainboard Manual
USB 2.0 Controller Mode
This item allows you to select the operation mode of the USB 2.0 controller.
Options: HiSpeed (Default)
USB 2.0-480Mbps
FullSpeed
USB 1.1-12Mbps
BIOS EHCI Hand-Off
This item allows you to enable support for operating systems without an EHCI
hand-off feature.
Options: Enabled (Default) / Disabled
USB Mass Storage Device Configuration
Advanced
BIOS SETUP UTILITY
USB Mass Storage Device Configuration
USB Mass Storage Reset Delay [20 Sec]
Device #
Emulation Type
[Auto]
Number of seconds
POST waits for the
USB mass storage
device after start
unit command.
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
USB Mass Storage Reset Delay
This item allows you to set the reset delay for USB mass storage device.
Options: 20 Sec (Default) / 10 Sec / 30 Sec / 40 Sec
Emulation Type
This item allows you to select the emulation type of the USB mass storage device.
Options: Auto (Default) / Floppy / Forced FDD / Hard Disk / CDROM
38
BIPV10-IAP
3.3
PCI/PNP MENU
This section describes configuring the PCI bus system. PCI, or Personal Computer
Interconnect, is a system which allows I/O devices to operate at speeds nearing the
speed of the CPU itself uses when communicating with its own special components.
Notice
z
Beware of that setting inappropriate values in items of this menu may cause
system to malfunction.
Main
Advanced
PCIPnP
BIOS SETUP UTILITY
Boot
Chipset
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
Clear NVRAM
Plug & Play O/S
PCI Latency Timer
Allocate IRQ to PCI VGA
Palette Snooping
PCI IDE BusMaster
OffBoard PCI/ISA IDE Card
> PCI Resource
Exit
Clear NVRAM during
System Boot.
[No]
[No]
[64]
[Yes]
[Disabled]
[Enabled]
[Auto]
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Clear NVRAM
This item allows you to clear the data in the NVRAM (CMOS) by selecting “Yes”.
Options: No (Default) / Yes
Plug & Play OS
When set to YES, BIOS will only initialize the PnP cards used for the boot sequence
(VGA, IDE, SCSI). The rest of the cards will be initialized by the PnP operating
system like Window™ 95. When set to NO, BIOS will initialize all the PnP cards.
For non-PnP operating systems (DOS, Netware™), this option must set to NO.
Options: No (Default) / Yes
PCI Latency Timer
This item controls how long a PCI device can hold the PCI bus before another takes
over. The longer the latency, the longer the PCI device can retain control of the bus
before handing it over to another PCI device.
Options: 64 (Default) / 32 / 96 / 128 / 160 / 192 / 224 / 248
39
Mini-ITX Mainboard Manual
Allocate IRQ to PCI VGA
This item allows BIOS to choose a IRQ to assign for the PCI VGA card.
Options: Yes (Default) / No
Palette Snooping
Some old graphic controllers need to “snoop” on the VGA palette and then map it to
their display as a way to provide boot information and VGA compatibility. This
item allows such snooping to take place.
Options: Disabled (Default) / Enabled
PCI IDE BusMaster
This item is a toggle for the built-in driver that allows the onboard IDE controller to
perform DMA (Direct Memory Access) transfers.
Options: Enabled (Default) / Disabled
OffBoard PCI/ISA IDE Card
Some PCI IDE cards may require this to be set to the PCI slot number that is
holding the card.
Options: Auto (Default) / PCI Slot1 ~ 6
OffBoard PCI/ISA Primary & Secondary IRQ
This item allows you to set IRQ of non-onboard PCI/ISA IDE controller adapter.
Options: Disabled (Default) / INTA / INTB / INTC / INTD / Hardwired
40
BIPV10-IAP
PCI Resource
PCIPnP
BIOS SETUP UTILITY
PCI Resource
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ11
IRQ14
IRQ15
DMA
DMA
DMA
DMA
DMA
DMA
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
Channel
Channel
Channel
Channel
Channel
Channel
0
1
3
5
6
7
Reserved Memory Size
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
Available: Specified
IRQ is available to be
used by PCI/PnP
devices.
Reserved: Specified
IRQ is reserved for
use by Legacy ISA
devices.
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
[Disabled]
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
IRQ3/4/5/7/9/10/11/14/15
These items will allow you to assign each system interrupt a type, depending on the
type of device using the interrupt. The option “Available” means the IRQ is going
to assign automatically.
Options: Available (Default) / Reserved
DMA Channel 0/1/3/5/6/7
These items will allow you to assign each DMA channel a type, depending on the
type of device using the channel. The option “Available” means the channel is
going to assign automatically.
Options: Available (Default) / Reserved
Reserved Memory Size
This item allows BIOS to reserve certain memory size for specific PCI device.
Options: Disabled (Default) / 16K / 32K / 64K
Reserved Memory Address
Options: C800 (Default) / C000 / C400 / CC00 / D000 / D400 / D800 / DC00
41
Mini-ITX Mainboard Manual
3.4
BOOT MENU
This menu allows you to setup the system boot options.
Main
Advanced
PCIPnP
BIOS SETUP UTILITY
Boot
Chipset
Specifies the
Boot Device
Priority sequence.
Boot Settings Configuration
>
>
>
>
Boot Device Priority
Hard Disk Drives
Removable Drives
CD/DVD Drives
Quick Boot
Full Screen LOGO Show
AddOn ROM Display Mode
Bootup Num-Lock
PS/2 Mouse Support
Wait For F1 If Error
Hit DEL Message Display
Interrupt 19 Capture
Exit
[Enabled]
[Disabled]
[Force BIOS]
[On]
[Auto]
[Enabled]
[Enabled]
[Disabled]
Select Screen
Select Item
Enter Go to Sub Screen
F1
General Help
F10 Save and Exit
ESC Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Boot Device Priority
Items in this sub-menu specify the boot device priority sequence from the available
devices. The number of device items that appears on the screen depends on the
number of devices installed in the system.
Hard Disk Drives
The BIOS will attempt to arrange the hard disk boot sequence automatically. You
can also change the booting sequence. The number of device items that appears on
the screen depends on the number of devices installed in the system.
Removable Drives
The BIOS will attempt to arrange the removable drive boot sequence automatically.
You can also change the booting sequence. The number of device items that
appears on the screen depends on the number of devices installed in the system.
CD/DVD Drives
The BIOS will attempt to arrange the CD/DVD drive boot sequence automatically.
You can also change the booting sequence. The number of device items that
appears on the screen depends on the number of devices installed in the system.
42
BIPV10-IAP
Quick Boot
Enabling this option will cause an abridged version of the Power On Self-Test
(POST) to execute after you power up the computer.
Options: Enabled (Default) / Disabled
Full Screen LOGO Disaply
This item allows you to enable/disable Full Screen LOGO Show function.
Options: Disabled (Default) / Enabled
AddOn ROM Display Mode
This item sets the display mode for option ROM.
Options: Force BIOS (Default) / Keep Current
Bootup Num-Lock
Selects the NumLock State after the system switched on.
Options: On (Default) / Off
PS/2 Mouse Support
This BIOS feature determines if the BIOS should reserve IRQ12 for the PS/2 mouse
or allow other devices to make use of this IRQ.
Options: Auto (Default) / Disabled / Enabled
Wait for ‘F1’ If Error
This BIOS feature controls the system's response when an error is detected during
the boot sequence.
Options: Enabled (Default) / Disabled
Hit ‘DEL’ Message Display
This BIOS feature allows you to control the display of the Hit “DEL” to enter Setup
message during memory initialization.
Options: Enabled (Default) / Disabled
Interrupt 19 Capture
Interrupt 19 is the software interrupt that handles the boot disk function.
to Enabled, this item allows the option ROMs to trap interrupt 19.
Options: Disabled (Default) / Enabled
When set
43
Mini-ITX Mainboard Manual
3.5
CHIPSET MENU
This submenu allows you to configure the specific features of the chipset installed
on your system. This chipset manage bus speeds and access to system memory
resources, such as DRAM. It also coordinates communications with the PCI bus.
Notice
z
Beware of that setting inappropriate values in items of this menu may cause
system to malfunction.
Main
Advanced
PCIPnP
BIOS SETUP UTILITY
Boot
Chipset
Advanced Chipset Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
Exit
Configure North Bridge
features.
> North Bridge Configuration
> South Bridge Configuration
Select Screen
Select Item
EnterGo to Sub Screen
F1
General Help
F10 Save and Exit
ESC Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
North Bridge Configuration
BIOS SETUP UTILITY
Chipset
North Bridge Chipset Configuration
PCI MMIO Allocation:
DRAM Frequency
Configure DRAM Timing by SPD
DRAM CAS# Latency
DRAM RAS# to CAS# Delay
DRAM RAS# Precarge
DRAM RAS# Activate to Precha
[Auto]
[Enabled]
[5]
[5 DRAM Clocks]
[5 DRAM Clocks]
[15 DRAM Clocks]
Initate Graphic Adapter
Internal Graphics Mode Select
[PCI/IGD]
[Enabled,8MB]
PEG Port Congiguration
> Video Function Configuration
Options
Auto
667 MHz
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
44
DRAM Frequency
BIPV10-IAP
This item allows you to set the frequency of DRAM.
Options: Auto (Default) / Max MHz
Configure DRAM timing by SPD
This item allows you .to determine DRAM timing by SPD
Options: Enabled (Default) / Disabled
DRAM CAS# Latency
Options: 5 (Default) / 3 / 4 / 6
DRAM RAS# to CAS# Delay
Options: 5 DRAM Clocks (Default) / 3 ~ 10DRAM Clocks
DRAM RAS# Precharge
Options: 5 DRAM Clocks (Default) / 3 ~ 10DRAM Clocks
DRAM RAS# Activate to Precharge
Options: 15 DRAM Clocks (Default) / 9 ~ 24 DRAM Clocks
Initate Graphic Adapter
Select which graphics controller to use as the primary boot device.
Options: PCI/IGD (Default) / IGD
Internal Graphics Mode Select
Select the amount of system memory used by the Internal graphics device. This item
will be different as your memory modules. When the memory size is decided, this
frame buffer size will also be fixed.
Options: Enabled, 8MB (Default)
45
Mini-ITX Mainboard Manual
Video Function Configuration
BIOS SETUP UTILITY
Chipset
Video Function Configuration
Options
DVMT Mode Select
DVMT/FIXED Memory
[DVMT Mode]
[256MB]
Boot Display Device
LVDS SUPPORT
Local Flat Panel Scaling
Flat Panel Type
[D-SUB + LVDS]
[Enabled]
[Auto]
[1024 X 768]
Fixed Mode
DVMT Mode
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
DVMT Mode Select
This item allows you to select the DVMT mode.
Options: DVMT Mode (Default) / Fixed Mode
DVMT/FIXED Memory
DVMT stands for “Dynamic Video Memory Technology”. This is an enhancement
of the unified memory architecture (UMA) concept. DVMT will set the optimum
amount of memory to be allocated for a balance between graphics and system
performance. DVMT dynamically respond to system requirements and applications
demands, by allocating the proper amount of display, texturing and buffer memory
after the operating system has booted.
Options: 256MB (Default) / 128MB / Maximum DVMT
Boot Display Device
This item allows you to select the display device.
Options: D-SUB + LVDS (Default) / LVDS / D-SUB
LVDS Support
Options: Enabled (Default) / Disabled
Local Flat Panel Scaling
This item allows you to select local flat panel scaling
Options: Auto (Default) / Forced Scaling / Disabled
46
BIPV10-IAP
Flat Panel Type
This item allows you to select flat panel type.
Options: 1024x768 (Default) / 640x480 / 800x600 / 1280x1024 / 1280x764 /
1366x768 / 1400x1050 / 1280x768 / 1680x1050 / 1920x1200 / 1280x800 /
2048x1536
South Bridge Configuration
BIOS SETUP UTILITY
Chipset
South Bridge Chipset Configuration
USB Functions
USB 2.0 Controller
HDA Controller
SMBUS Controller
[8 USB Ports]
[Enabled]
[Auto]
[Enabled]
Onboard
Onboard
Onboard
Onboard
[Enabled]
[Disabled]
[Enabled]
[Disabled]
LAN
LAN
LAN
LAN
1
ROM1
2
ROM2
PCIE High Priority Port
SLP_S4# Min. Assertion Width
[Disabled]
[1 to 2 seconds]
> PCI Express Configuration
Options
Disabled
2 USB Ports
4 USB Ports
6 USB Ports
8 USB Ports
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
USB Functions
The item determines the activation of USB port.
Options: 8 USB Ports (Default) / 2 USB Ports / 4 USB Ports / 6 USB Ports /
Disabled
USB 2.0 Controller
This entry is to enabled/ disabled EHCI controller only. This BIOS itself may/may
not have high speed USB support. If the BIOS has high speed USB support, the
support will be automatically turned on when high speed devices were attached.
Options: Enabled (Default) / Disabled
HDA Controller
This item allows you to control the Audio support.
Options: Auto (Default) / Disabled
47
Mini-ITX Mainboard Manual
SMBUS Controller
This BIOS feature controls the I/O buffers for the SMBus.
Options: Enabled (Default) / Disabled
Onboard LAN 1/2
This item allows you to enable or disable the Onboard LAN.
Options: Enabled (Default) / Disabled
Onboard LAN ROM 1/2
This item allows you to select the Onboard LAN Boot ROM.
Options: Disabled (Default) / Enabled
PCIE High Priority Port
Options: Disabled (Default) / Port 0 ~ Port 3
SLP_S4# Min. Assertion Width
Options: 1 to 2 seconds (Default) / 4 to 5 seconds / 3 to 4 seconds / 2 to 3 seconds
PCI Express Configuration
BIOS SETUP UTILITY
Chipset
PCI Express Configuration
Relaxed Ordering
Maximum Payload Size
Extended Tag field
No Snoop
Maximum read Request Size
Active State Power Management
Extended Synch
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Disabled]
[Auto]
Enables/Disables
Pci Express Device
Relaxed Ordering.
Select Screen
Select Item
Enter Update
F1
General Help
F10 Save and Exit
ESC Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
48
BIPV10-IAP
Relaxed Ordering
The item enables/disables PCI Express Device Relaxed Ordering.
Options: Auto (Default) / Disabled / Enabled
Maximum Payload Size
The item sets Maximum Payload of PCI Express Device or allows System BIOS to
select the value.
Options: Auto (Default) / 128 Byte / 256 Byte / 512 Byte / 1024 Byte / 2048 Byte /
4096 Byte
Extended Tag Field
If this item is enabled, the system allows Device to use 8-bit TAG field as a
requester.
Options: Auto (Default) / Disabled / Enabled
No Snoop
The item enables/disables PCI Express Device No Snoop option.
Options: Auto (Default) / Disabled / Enabled
Maximum Read Request Size
The item sets Maximum Read Request Size of PCI Express Device or allows
System BIOS to select the value.
Options: Auto (Default) / 128 Bytes / 256 Bytes / 512 Bytes / 1024 Bytes / 2048
Bytes / 4096 Bytes
Active State Power Management
The item enables/disables PCI Express L0s and L1 link power states..
Options: Disabled (Default) / Enabled
Extended Synch
If this item is enabled, the system allows generation of Extended Synchronization
patterns.
Options: Auto (Default) / Disabled / Enabled
49
Mini-ITX Mainboard Manual
3.6
EXIT MENU
This menu allows you to load the optimal default settings, and save or discard the
changes to the BIOS items.
Main
Advanced
PCIPnP
BIOS SETUP UTILITY
Boot
Chipset
Exit Options
Save Changes and Exit
Discard Changes and Exit
Discard Changes
Load Optimal Defaults
Exit
Exit system setup
after saving the
changes.
F10 key can be used
for this operation.
Security Settings
> Security
Select Screen
Select Item
EnterGo to Sub Screen
F1
General Help
F10 Save and Exit
ESC Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Save Changes and Exit
Save all configuration changes to CMOS RAM and exit setup.
Discard Changes and Exit
Abandon all changes made during the current session and exit setup.
Discard Changes
Abandon all changes made during the current session and restore the previously
saved values.
Load Optimal Defaults
This selection allows you to reload the BIOS when problem occurs during system
booting sequence. These configurations are factory settings optimized for this
system.
50
BIPV10-IAP
Security
This sub-menu allows you to provide/revise supervisor and user password.
BIOS SETUP UTILITY
Security Settings
Supervisor Password :Not Installed
User Password
:Not Installed
Change Supervisor Password
User Access Level
Change User Password
Clear User Password
Password Check
Exit
Install or Change the
password.
[Full Access]
[Setup]
Boot Sector Virus Protection [Disabled]
Select Screen
Select Item
EnterChange
F1
General Help
F10 Save and Exit
ESC Exit
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Change Supervisor Password
Setting the supervisor password will prohibit everyone except the supervisor from
making changes using the CMOS Setup Utility. You will be prompted with to enter
a password.
User Access Level
This item allows supervisor to set the user level.
Options: Full Access (Default) / No Access / View Only / Limited
Change User Password
If the Supervisor Password is not set, then the User Password will function in the
same way as the Supervisor Password. If the Supervisor Password is set and the
User Password is set, the “User” will only be able to view configurations but will
not be able to change them.
Clear User Password
This item is for clearing user password.
51
Mini-ITX Mainboard Manual
Password Check
This item is for setting the timing that checking password.
Options: Setup (Default) / Always
Boot Sector Virus Protection
This option allows you to choose the VIRUS Warning feature that is used to protect
the IDE Hard Disk boot sector. If this function is enabled and an attempt is made to
write to the boot sector, BIOS will display a warning message on the screen and
sound an alarm beep.
Options: Disabled (Default) / Enabled
52
BIPV10-IAP
CHAPTER 4: USEFUL HELP
4.1
DRIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your mainboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your mainboard and operating system. Click
on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
53
Mini-ITX Mainboard Manual
4.2
AMI BIOS BEEP CODE
Boot Block Beep Codes
Number of Beeps
1
2
3
4
5
7
10
11
12
13
Description
No media present. (Insert diskette in floppy drive A:)
“AMIBOOT.ROM” file not found in root directory of diskette in
A:
Insert next diskette if multiple diskettes are used for recovery
Flash Programming successful
File read error
No Flash EPROM detected
Flash Erase error
Flash Program error
“AMIBOOT.ROM” file size error
BIOS ROM image mismatch (file layout does not match
image present in flash device)
POST BIOS Beep Codes
Number of Beeps
1
3
6
7
8
Description
Memory refresh timer error
Base memory read/write test error
Keyboard controller BAT command failed
General exception error (processor exception interrupt error)
Display memory error (system video adapter)
Troubleshooting POST BIOS Beep Codes
Number of Beeps
1, 3
6, 7
8
54
Troubleshooting Action
Reseat the memory, or replace with known good modules.
Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.
z If beep codes are generated when all other expansion
cards are absent, consult your system manufacturer’s
technical support.
z If beep codes are not generated when all other expansion
cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.
If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.
BIPV10-IAP
4.3
TROUBLESHOOTING
Probable
1.
There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work
2.
Indicator light on keyboard does
not shine.
System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.
System does not boot from a hard disk
drive, but can be booted from optical
drive.
Solution
1.
2.
3.
Make sure power cable is
securely plugged in.
Replace cable.
Contact technical support.
Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.
1.
Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from an optical
1.
Back up data and applications
drive. Hard disks can be read,
files.
applications can be used, but system 2.
Reformat the hard drive.
fails to boot from a hard disk.
Re-install applications and data
using backup disks.
Screen message shows “Invalid
Review system’s equipment. Make sure
Configuration” or “CMOS Failure.”
correct information is in setup.
System cannot boot after user installs a 1.
Set master/slave jumpers
second hard drive.
correctly.
2.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
2011/08/29
55
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising