Front End Loader
E-series
Front End Loader
L1204E I L1506E I L1706E I L1806E I L2106E I L2606E I L2706E
Customer inspir
Production drive
Serious productivity demands serious
inspiration. Many of the innovative
features and advantages of the
E-series loaders have come from the
brightest minds in the industry owners and users such as yourself.
By fully understanding and responding to your needs. The
E-series delivers the most advanced wheeled loader range with
class-leading features available in the market. These productive
material movers are equipped with spacious cabs,
low-maintenance cooling systems, fatigue-beating ergonomics
and even more options. All with the goal of increasing productivity
and uptime, while lowering daily operating costs. Owners,
operators, and service technicians will benefit from the numerous
features found in Bell Loaders.
E-series Specification
2
L1204E
L1506E
L1706E
L1806E
L2106E
L2606E
L2706E
Rated Net Power 92 kW
121 kW
139 kW
173 kW
197 kW
227 kW
248 kW
Bucket Capacity
1.9 m3
2.3 m3
2.7 m3
3.3 m3
3.6 m3
4.4 m3
4.7 m3
Tipping Load
8 072 kg
9 434 kg
12 039 kg
13 126 kg
14 204 kg
17 123 kg
17 588 kg
Breakout Force
8 212 kg
10 284 kg
12 920 kg
15 378 kg
14 398 kg
19 416 kg
18 905 kg
Operating Weight
11 055 kg
12 820 kg
15 185 kg
18 160 kg
19 130 kg
24 182 kg
26 210 kg
red
en
PowerTechTM emissions-certified diesel engines deliver power without compromise in all conditions.
Torque reserves are impressive, it’s an E-series advantage that helps maintain excellent boom and bucket
speed in and out of the pile. For fully heaped loads, even in wet or hard-packed material.
Low center of gravity and optimized fore-and-aft balance deliver impressive stability and full-turn tippingload capacities. A wide footprint provides additional lateral stability for handling heavy loads and working
on rough terrian.
Unsurpassed powertrain and hydraulic performance helps maintain quick ground speed and boom lift,
even on steep ramps. For faster cycles.
3
Hard work
made easier
4
Platforms, handrails and steps allow
uninterrupted three point access. There are
no crossbars, decreasing the risk of
slipping.
Expanded sealed-switch module gives
fingertip control of keyless start and 24 other
machine functions. Enables the operator to
optimally set up the machine to suit operating
conditions.
Ten-percent more front glass, low-profile
front console, large side and rear windows
allow unsurpassed 360-degree visibility.
Optional rearview camera and radar
object-detection system give an operator
exceptional rear visibility on the LCD
monitor screen. An audible alert is emitted
for extra awareness in tight and high-traffic
areas.
Available premium high/wide-back
air-suspension seat adjusts multiple ways
for daylong comfort and support.
Brake and throttle pedals have been
repositioned and the front-console
reshaped to make way for more
legroom and comfort.
Steering wheel and hydraulic levers are
within easy reach and move with the
operator for more control with less
fatigue.
Automotive-style directional louvers
provide effective airflow to help keep
the glass clear and pressurised cab
comfortable.
You will find plenty of space for
fluid bottles to stow a cooler and
other carryons. Convenient 12-volt
port powers cell phones and other
electronic devices.
Cab noise has been noticeably minimized
to help reduce operator fatgue.
What operator wouldn’t be more productive in the high-back
suspension seat of an E-series Loader? An enhanced multifunction
monitor displays operating and diagnostic info on a colour LCD screen
with easy-on-the-eyes clarity.
Expansive tinted front glass and a low-profile console provide a commanding view of the work
ahead. The quiet and spacious cab boast generous leg room and exceptional ergonomics,
including fatigue-beating features like seat-mounted loader controls. And an expanded sealedswitch module with keyless start and easy push-button operation of even more functionality.
5
Maximise your
productivity
If you want to get a handle on increased
productivity, put your operator behind
the controls of an E-series Loader.
But it’s not just their big torque reserves that make them such
impressive performers. Single-lever joystick controls provide smooth,
near-effortless control. Excavator-style hydraulics sense the load and
deliver the flow needed for smooth combined functions and fast work
cycles. You won’t find a smoother-shifting loader, either. The
PowerShiftTM torque-converter transmission employs SmartShiftTM
technology to continuously evaluate speed and load conditions, and
adjusts clutch-pack engagement to suit.
6
Standard single-lever joystick with an FNR
selector for convenient direction and
full-range gear changes. Includes an
innovative Quick-Shift feature for
pushbutton gear changes, one gear at a
time.
Programmable clutch cuttoff increases
productivity in all kinds of conditions.
Engaging the brakes disconnects the
transmission while maintaining high engine
speed. For smooth dumps, fast cycles, and
no machine rollback.
Boom-height kick-out sets maximum
desired dump height, while return-to-carry
determines lowered-boom position. Use
these two E-series advantages to speed
production in repetitive loading application.
Vital and general operating information,
including transmission mode, gear, engine,
rpms and ground speed.
Optional embedded payload scale weighs
each bucket load, helping fill trucks to the
max.
Advanced onboard diagnostics with sensor
information, calibration and switch checks.
Keyless-start security system requires a
numeric pass code (when enabled). Helps
prevent unauthorized machine operation.
SmartShiftTM delivers smooth-as-silk gear
changes, regardless of whether the bucket
is empty or fully loaded.
Spin control boosts productivity by
improving traction in loose material or
difficult underfoot conditions. Reduces
tyre wear, fuel costs and operator
fatigue.
Responsive steering combines with full
80-degree articulation for exceptional
maneuverability in tight areas - and
faster cycle times.
Optional ride (Standard L2606E and
L2706E) control smoothes travel over
rough undulated terrain, allowing these
loaders to navigate jobsites more quickly
without losing their loads for maximum
material rention.
Load-sensing closed-center hydraulics
deliver only the power required for
smooth boom and bucket functions.
So there’s no wasted power or fuel.
7
Uncompromised
Uptime
When you have hungry hoppers or
empty trucks depending on your
loader, downtime is more than a
downer. Its unacceptable.
Boost your uptime (and your bottom line) with E-series advantages
such as solid-state electronics, highly efficient Quad-CoolTM, and
an advanced diagnostic monitor. You’ll also benefit from traditional
durability features such as heavy-duty wet-sleeve engines,
self-adjusting wet-disc brakes, four-plate loader towers and
double-tapered articulation-joint roller bearings. When you know
how they’re built, you’ll run a Bell.
Quad-CoolTM places the radiator, airconditioner condenser, intercooler
hydraulic, transmission and axle coolers in a
unique boxed configuration that’s isolated
from engine heat. For increased efficiency
and durability.
8
Hydrostatic swing-out fan automatically
reverses at predetermined intervals, ejecting
debris from the radiator and cooler cores.
Or choose your own cleaning cycles
through the monitor.
Optional (Standard L2606E and L2706E)
5-speed transmission with torque converter
lockup increases acceleration, speeds
cycles and optimizes power and fuel
efficiency during transport, roading and
ramp climbing.
d
Powered cab pre-cleaner provides a
cleaner interior when working in airborne
debris.
Advanced air-screen kits protect the
engine and cooling system from debris
while increasing airflow and preventing
overheating.
Large-capacity fuel tanks let you run
longer between fill-ups.
Find fewer fuses, relays, connecters and
wiring harnesses. Instead, highly reliable
circuit-board technology and sealed
solid-state switches ensure the electrical
integrity you need.
Expansive air-inlet surfaces increase airflow
and prevent overheating, while keeping the
cooling cores debris free. Three-millimeter
side-screen perforations serve as a “first
filter”.
Sealed-switch module keeps out dust,
moisture and debris. Proven marinegrade touchpad eliminates rocker
switches and nearly 100 wires and
unsealed connections.
Automatic park brake, bypass-start
protection, continuous handrails and wide
slip-resistant steps and platforms help keep
operators out of harm’s way.
9
The buck
stops here
Servicing and maintenance should
be simple and cost effective and it is
on the E-series.
Swing open the large side panels and you’ll see the many
ways these loaders minimise maintenance. The unique
Quad-CoolTM system and swing-out fan provide wide-open
access to both sides of the individually mounted coolers for
simplified cleanout. Grouped sameside service points make
quick work of the daily routine. Easy-to read sight gauges,
quick-change filters, extended service intervals and advanced
self-diagnostics - plus numerous other time and money saving
features help make maintenance manageable and improves
owning and operating costs.
Vertical spin-on engine, transmission and
in-tank hydraulic filters; quick-release fuel
filters; and environmentally friendly fluid
drains allow quick, no-spill changes.
10
Conveniently displayed periodic lubrication
and maintenance chart helps ensure that
nothing is overlooked.
If something goes wrong, the easy-tonavigate LCD monitor provides diagnostics
info and even offers possible
troubleshooting solutions to reduce
downtime.
Large hinged service doors swing open
wide for ample ground-level access. All
daily servicing is done on the same side.
Technicians will appreciate the commonsense locations and ease with which
powertrain, hydraulic and cab filters are
replaced. Common hydraulic and
transmission fluid and filter change
intervals further simplify service.
Lockable compartment swings open,
offering convenient ground-level access
to batteries and electrical disconnect
switch.
500, 2 000 and 4 000 hour engine,
transmission and hydraulic oil and filter
intervals decrease planned downtime and
expense.
Auto-idle automatically applies the brakes
and reduces engine speed to help
conserve fuel after a pre determined
period of inactivity. Auto shutdown turns
off the engine after an extended time of
inactivity.
See-through reservoir and sight
gauges simplify coolant, hydraulic and
transmission fluid-level checks.
Coolers resist plugging, and both sides
are easily accessible for cleaning.
Hydraulically driven fan runs only as
needed, reducing fuel consumption and
debris flow through the cores.
11
Technical Data - L1204E
engine
Type
John Deere POWERTECHTM 4045H
Non-road emissions standard
Certified to EPA Tier 3 emissions
Cylinders
4
Displacement
4.5 l
Net Peak Power
95 kW @ 2 100 rpm
Net Peak Torque
515 Nm @ 1 400 rpm
Fuel System
High Pressure Common Rail,
Electronically controlled
Aspiration
Turbocharged, charge air cooled
Air Cleaner
Dual-element dry type, restriction
indicator in cab monitor for service
Fan Drive
Hydraulically driven, proportionally
controlled, fan aft coolers
Lubrication
Full-flow spin-on filter and integral
cooler
Electrical System
24 volt with 80-amp alternator
(100-amp alternator optional)
Batteries
950 CCA (each)
transmission
Type
Countershaft-type PowerShiftTM
Torque Converter
Single stage, single phase
Shift Control
Electronically modulated, adaptive,
load and speed dependant
Operator Interface
Joystick-mounted FNR and gear
select lever, kick-down button on
Joystick
Shift Modes
Manual/auto (1st-4th or 2nd-4th);
quick-shift button with two selectable
modes: kick down or kick up/down;
and three clutch cutoff settings
adjustable on switch pad
Transmission Fluid with Vertical
Filter
18.5 l
Travel Speeds
Forward Maximum Gear 1
Gear 2
Gear 3
Gear 4
7.3 km/h
12.1 km/h
23.1 km/h
36.0 km/h
Hydraulic Reservoir and Filters
91 l
Reverse Maximum
Gear 1
Gear 2
Gear 3
Gear 4
7.6 km/h
13.0 km/h
25.3 km/h
NA
axles/brakes
Final Drive
Heavy-duty outboard planetary
Differentials
Manual locking front, conventional
rear
Rear Axle Oscilllation, Stop to
Stop
24o
Brakes
(conform to SAE J1473, ISO3450)
Service Brakes
Hydraulically actuated, midboard final
drive carrier mounted, oil cooled, selfadjusting retractors, multi disc
Parking Brakes
Automatic spring applied,
hydraulically released, driveline
mounted, oil cooled, multi-disc
Tyres
Standard Sizes
17.5 x 25, L4, 12 Ply
Refill capacity
Fuel Tank
(with ground-level fueling)
242 l
Cooling System
19 l
Engine Oil with Vertical Spin-on
Filter
17.5 l
Axle Oil (front and rear)
22 l
Park Brake Oil (wet disc)
0.3 l
Hydraulic System/
Steering
Pump (Loader and Steering)
Variable-displacement, load-sensing
axial-piston pump; closed-center,
pressure-compensating system
Maximium Rated Flow
140 l/m @ 6 895 kPa and 2 350 rpm
System Relief Pressure
(Loader and Steering)
24 821 kPa
Loader Controls
Two-function valve; single- or duallever controls; control lever lockout
feature; optional third- and fourthfunction valve with auxiliary lever
Steering (conforms to SAE J1511)
Type
Power, fully hydraulic
Articulation Angle
80º arc (40º each direction)
Hydraulic Cycle Times Standard
Z-Bar
Raise
5.9 sec
Dump
1.0 sec
standard z-bar pin-on
Type Bucket Information
Standard Z-Bar Linkage, with PinOn General-Purpose Bucket with
Bolt-On, Segments and Teeth
Bucket Type/Size Capacity, Heaped
1.9 m3
Capacity, Struck
1.6 m3
Bucket Weight 837 kg
Bucket Width 2.55 m
Breakout Force
8 212 kg
Tipping Load, Straight
9 275 kg
Tipping Load, 40o Full Turn
8 072 kg
Safe Operating Load
4 036 kg
Reach, 45o Dump, Clearance
(2.13 m)
1.44 m
Reach, 45o Dump, Full Height
•• 1.04 m
Dump Clearance, 45o, Full Height
• 2.67 m
Overall Length, Bucket on Ground
••• 6.76 m
Lower (float down)
2.4 sec
Loader Clearance Circle, Bucket
Carry Position
11.10 m
Total
9.3 sec
Turning Radius (measured to
centerline of outside tyre)
4.75 m
Operating Weight
11 055 kg
Material
Loose Material
kg/m3
Caliche
1 250
Cinders590
Clay and gravel, dry
1 420
Clay and gravel, wet
1 540
Clay, dry
1 480
Clay, natural bed
1 660
Clay, wet
1 660
Coal, anthracite, broken
1 100
Coal, bituminous, broken
830
Earth, dry, packed
1 510
Earth, loam
1 250
12
Earth, wet, excavated
Granite, broken or large crushed
Gravel, dry
Gravel, dry 13 to 50 mm
Gravel, pit run (graveled sand)
Gravel, wet 13 to 50 mm
Gypsum, crushed
Limestone, broken or crushed
Magnetite, iron ore
Phosphate rock
Pyrite, iron ore
kg/m3
kg/m3
1 600
1 660
1 510
1 690
1 930
2 020
1 600
1 540
2 790
1 280
2 580
Sand and gravel, dry
1 720
Sand and gravel, wet
2 020
Sand, dry
1 420
Sand, wet
1 840
Sandstone, broken
1 510
Shale
1 250
Slag, broken
1 750
Stone, crushed
1 600
Topsoil950
Dimensions with Pin-On Bucket
Standard Z-Bar Linkage, with Pin-On General-Purpose Bucket with Bolt-On
Segments and Teeth
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Height to Top of Cab and Canopy
Ground Clearance
Length from Centerline to Front Axle Wheelbase
Dump Clearance •
Height to Hinge Pin, Fully Raised Dump Reach ••
Maximum Digging Depth Overall Length •••
Maximum Rollback at Ground Level
Maximum Rollback, Boom Fully Raised Maximum Bucket Angle, Fully Raised
Overall Bucket Width
Wheel Track
Outside Wheel Width
Full Turn Radius, Inside Full Turn Radius, Outside 3.15 m
0.396 m
1.37 m
2.77 m
2.67 m
3.61 m
1.02 m
0.105 m
6.76 m
39º
55º
50º
2.550 m
1.910 m
2.366 m
4.321 m
5.550 m
Attachment Options
BUCKET OPTONS
Size 1.9 m3
1.9 m3
1.3 m3
1.3 m3
1.4 m3
3 m3
3.4 m3
Type
GP
GP
High Density
High Density
High Density Coal Wood Chip Blade/Lip
Straight
Straight
Straight
Straight
Spade
Straight
Straight
Teeth
Bolt-on 2 strap, male adaptors
None
Bolt-on 2 strap, male adaptors
None
None
None
None Cutting Edge
Segments
4 Piece Bolt-on
Segments
4 Piece Bolt-on
Weld-on Half Arrows
4 Piece Bolt-on
4 Piece Bolt-on
QUICK ATTACH BUCKETS
Size Type
1.9 m3
GP
1.9 m3
GP
3.4 m3
Wood Chip Blade/Lip
Straight
Straight
Straight
Teeth
Bolt-on 2 strap, male adaptors
None
None Cutting Edge
Segments
4 Piece Bolt-on
4 Piece Bolt-on
QUICK ATTACH IMPLEMENTS Quick attach pallet fork frame
Quick attach materials handling boom
Quick attach cane grab
LOG GRABS
Load fork log grab
Sorting grapple
Millyard grapple
13
Technical Data - L1506E
engine
Type
John Deere POWERTECHTM 6068H
Non-road emissions standard
Certified to EPA Tier 3 emissions
Cylinders
6 (2 valves per cylinder)
Displacement
6.8 l
Net Peak Power
125 kW @ 1 900 rpm
Net Peak Torque
673 Nm @ 1 600 rpm
Fuel System
High Pressure Common Rail
Aspiration
Turbocharged, charge air cooled
Air Cleaner
Dual-element dry type, restriction
indicator in cab monitor for service
Fan Drive
Hydraulically driven, proportionally
controlled, fan aft coolers
Lubrication
Full-flow spin-on filter and integral
cooler
Electrical System
24 volt with 80-amp alternator
(100-amp alternator optional)
Shift Modes
Manual/auto (1st-4th or 2nd-4th);
quick-shift button with two selectable
modes: kick down or kick up/down;
and three clutch cutoff settings
adjustable on switch pad
Transmission Fluid with Vertical
Filter
18.5 l
Travel Speeds
Forward Maximum Gear 1
Gear 2
Gear 3
Gear 4
7.2 km/h
11.9 km/h
22.8 km/h
35.7 km/h
Hydraulic Reservoir and Filters
91 l
Reverse Maximum
Gear 1
Gear 2
Gear 3
Gear 4
7.2 km/h
12.6 km/h
24.1 km/h
NA
axles/brakes
Final Drive
Heavy-duty outboard planetary
Differentials
Manual locking front, conventional
rear
Rear Axle Oscilllation, Stop to
Stop
24o
Brakes
(conform to SAE J1473, ISO3450)
Service Brakes
Hydraulically actuated, midboard final
drive carrier mounted, oil cooled, selfadjusting retractors, multi disc
Batteries (2 by 12V)
950 CCA (each)
Parking Brakes
Automatic spring applied,
hydraulically released, driveline
mounted, oil cooled, multi-disc
transmission
Type
Countershaft-type PowerShiftTM
Tyres
Standard Sizes
20.5 x 25, L5, 12 Ply
Torque Converter
Single stage, single phase
Shift Control
Electronically modulated, adaptive,
load and speed dependant
Operator Interface
Joystick-mounted FNR and gear
select lever, kick-down button on
Joystick
Refill capacity
Fuel Tank
(with ground-level fueling)
325 l
Cooling System
23 l
Engine Oil with Vertical Spin-on
Filter
19 l
Axle Oil (front and rear)
17 l
Park Brake Oil (wet disc)
0.3 l
Hydraulic System/
Steering
Pump (Loader and Steering)
Variable-displacement, load-sensing
axial-piston pump; closed-center,
pressure-compensating system
Maximium Rated Flow
189 l/m @ 6 895 kPa and 2 350 rpm
System Relief Pressure
(Loader and Steering)
25 166 kPa
Loader Controls
Two-function valve; single- or duallever controls; control lever lockout
feature; optional third- and fourthfunction valve with auxiliary lever
Steering (conforms to SAE J1511)
Type
Power, fully hydraulic
Articulation Angle
40º each direction
Hydraulic Cycle Times Standard
Z-Bar
Raise
5.8 sec
Dump
1.2 sec
standard z-bar pin-on
Type Bucket Information
Standard Z-Bar Linkage, with PinOn General-Purpose Bucket with
Bolt-On, Segments and Teeth
Bucket Type/Size Capacity, Heaped
2.3 m3
Capacity, Struck
2.0 m3
Bucket Weight 1 091 kg
Bucket Width 2.55 m
Breakout Force
10 284 kg
Tipping Load, Straight
10 896 kg
Tipping Load, 40o Full Turn
9 434 kg
Safe Operating Load
4 717 kg
Reach, 45o Dump, Clearance
(2.13 m)
1.49 m
Reach, 45o Dump, Full Height
•• 0.99 m
Dump Clearance, 45o, Full Height
• 2.76 m
Overall Length, Bucket on Ground
••• 7.43 m
Lower (float down)
3.2 sec
Loader Clearance Circle, Bucket
Carry Position
11.65 m
Total
10.2 sec
Turning Radius (measured to
centerline of outside tyre)
4.75 m
Operating Weight
12 820 kg
Material
Loose Material
kg/m3
Caliche
1 250
Cinders590
Clay and gravel, dry
1 420
Clay and gravel, wet
1 540
Clay, dry
1 480
Clay, natural bed
1 660
Clay, wet
1 660
Coal, anthracite, broken
1 100
Coal, bituminous, broken
830
Earth, dry, packed
1 510
Earth, loam
1 250
14
Earth, wet, excavated
Granite, broken or large crushed
Gravel, dry
Gravel, dry 13 to 50 mm
Gravel, pit run (graveled sand)
Gravel, wet 13 to 50 mm
Gypsum, crushed
Limestone, broken or crushed
Magnetite, iron ore
Phosphate rock
Pyrite, iron ore
kg/m3
kg/m3
1 600
1 660
1 510
1 690
1 930
2 020
1 600
1 540
2 790
1 280
2 580
Sand and gravel, dry
1 720
Sand and gravel, wet
2 020
Sand, dry
1 420
Sand, wet
1 840
Sandstone, broken
1 510
Shale
1 250
Slag, broken
1 750
Stone, crushed
1 600
Topsoil950
Dimensions with Pin-On Bucket
Standard Z-Bar Linkage, with Pin-On General-Purpose Bucket with Bolt-On
Segments and Teeth
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Height to Top of Cab and Canopy
Ground Clearance
Length from Centerline to Front Axle Wheelbase
Dump Clearance •
Height to Hinge Pin, Fully Raised Dump Reach ••
Maximum Digging Depth Overall Length •••
Maximum Rollback at Ground Level
Maximum Rollback, Boom Fully Raised Maximum Bucket Angle, Fully Raised
Overall Bucket Width
Wheel Track
Outside Wheel Width
Full Turn Radius, Inside Full Turn Radius, Outside 3.24 m
0.40 m
1.45 m
2.93 m
2.76 m
3.82 m
0.99 m
0.095 m
7.43 m
42º
55º
49º
2.550 m
1.947 m
2.470 m
4.545 m
5.800 m
Attachment Options
BUCKET OPTONS
Size 2.3 m3
2.3 m3
1.5 m3
1.5 m3
1.6 m3
2.7 m3
3.6 m3
4.5 m3
Type
GP
GP
High Density
High Density
High Density Low Density Coal Wood Chip
Blade/Lip
Straight
Straight
Straight
Straight
Spade
Straight
Straight
Straight
Teeth
Bolt-on 2 strap, male adaptors
None
Bolt-on 2 strap, male adaptors
None
None
None
None None
Cutting Edge
Segments
4 Piece Bolt-on
Segments
4 Piece Bolt-on
Weld-on Half Arrows
4 Piece Bolt-on
4 Piece Bolt-on
4 Piece Bolt-on
QUICK ATTACH BUCKETS
Size Type
2.3 m3
GP
Blade/Lip
Straight
Teeth
Bolt-on 2 strap, male adaptors
Cutting Edge
Segments
QUICK ATTACH IMPLEMENTS Quick attach pallet fork frame
Quick attach materials handling boom
Quick attach cane grab
LOG GRABS
Load fork log grab
Sorting grapple
Millyard grapple
15
Technical Data - L1706E
engine
Type
John Deere POWERTECHTM 6068H
Non-road emissions standard
Certified to EPA Tier 2 EU Stage II
Cylinders
6 (4 valves per cylinder)
Displacement
6.8 l
Net Peak Power
147 kW @ 1 800 rpm
Net Peak Torque
836 Nm @ 1 600 rpm
Fuel System
High Pressure Common Rail
Aspiration
Turbocharged, charge air cooled
Air Cleaner
Dual-element dry type, restriction
indicator in cab monitor for service
Fan Drive
Hydraulically driven, proportionally
controlled, fan aft coolers
Lubrication
Full-flow spin-on filter and integral
cooler
Electrical System
24 volt with 80-amp alternator
Batteries (2 by 12V)
950 CCA (each)
transmission
Type
Countershaft-type PowerShiftTM
Torque Converter
Single stage, single phase
Shift Control
Electronically modulated, adaptive,
load and speed dependant
Operator Interface
Joystick-mounted FNR and gear
select lever, kick-down button on
Joystick
Shift Modes
Manual/auto (1st-4th or 2nd-4th);
quick-shift button with two selectable
modes: kick down or kick up/down;
and three clutch cutoff settings
adjustable on switch pad
Transmission Fluid with Vertical
Filter
21 l
Travel Speeds
Forward Maximum Gear 1
Gear 2
Gear 3
Gear 4
7.6 km/h
12.5 km/h
25.0 km/h
39.5 km/h
Axle Oil Rear
17 l
Reverse Maximum
Gear 1
Gear 2
Gear 3
Gear 4
7.6 km/h
13.0 km/h
25.7 km/h
NA
axles/brakes
Final Drive
Heavy-duty inboard-mounted
planetary
Differentials
Hydraulic locking front with
conventional rear - standard; dual
locking front and rear - optional
Rear Axle Oscilllation, Stop to
Stop
24o
Brakes
(conform to SAE J1473, ISO3450)
Service Brakes
Hydraulically actuated, inboard
sun-shaft mounted, oil cooled, selfadjusting, single disc
Parking Brakes
Automatic spring applied,
hydraulically released, driveline
mounted, oil cooled, multi-disc
Tyres
Standard Sizes
20.5 x 25, L5, 12 Ply
Refill capacity
Fuel Tank
(with ground-level fueling)
352 l
Cooling System
27 l
Engine Oil with Vertical Spin-on
Filter
19 l
Axle Oil Front
22 l
Hydraulic Reservoir and Filters
110 l
Park Brake Oil (wet disc)
0.3 l
Hydraulic System/
Steering
Pump (Loader and Steering)
Variable-displacement, axial-piston
pump; closed-center, pressurecompensating system
Maximium Rated Flow
223 l/m @ 6 895 kPa and 2 350 rpm
System Relief Pressure
(Loader and Steering)
24 821 kPa
Steering (conforms to SAE J1511)
Type
Power, fully hydraulic
Articulation Angle
80º arc (40º each direction)
Hydraulic Cycle Times Standard
Z-Bar
Raise
5.9 sec
Lower (float down)
2.7 sec
standard z-bar pin-on
Type Bucket Information
Standard Z-Bar Linkage, with PinOn General-Purpose Bucket with
Bolt-On, Segments and Teeth
Bucket Type/Size Capacity, Heaped
2.7 m3
Capacity, Struck
2.3 m3
Bucket Weight 1 148 kg
Bucket Width 2.69 m
Breakout Force
12 920 kg
Tipping Load, Straight
13 922 kg
Loader Controls
Two-function valve; joystick control
or fingertip controls; hydraulicfunctionenable/disable; optional
third- and fourth-function valve with
auxiliary lever
Dump
1.3 sec
Turning Radius (measured to
centerline of outside tyre)
5.27 m
Tipping Load, 40o Full Turn
12 031 kg
Safe Operating Load
6 016 kg
Reach, 45o Dump, Clearance
(2.13 m)
1.57 m
Reach, 45o Dump, Full Height
•• 1.02 m
Dump Clearance, 45o, Full Height
• 2.86 m
Overall Length, Bucket on Ground
••• 7.76 m
Loader Clearance Circle, Bucket
Carry Position
12.24 m
Operating Weight
15 185 kg
Total
9.9 sec
Material
Loose Material
kg/m3
Caliche
1 250
Cinders590
Clay and gravel, dry
1 420
Clay and gravel, wet
1 540
Clay, dry
1 480
Clay, natural bed
1 660
Clay, wet
1 660
Coal, anthracite, broken
1 100
Coal, bituminous, broken
830
Earth, dry, packed
1 510
Earth, loam
1 250
16
Earth, wet, excavated
Granite, broken or large crushed
Gravel, dry
Gravel, dry 13 to 50 mm
Gravel, pit run (graveled sand)
Gravel, wet 13 to 50 mm
Gypsum, crushed
Limestone, broken or crushed
Magnetite, iron ore
Phosphate rock
Pyrite, iron ore
kg/m3
kg/m3
1 600
1 660
1 510
1 690
1 930
2 020
1 600
1 540
2 790
1 280
2 580
Sand and gravel, dry
1 720
Sand and gravel, wet
2 020
Sand, dry
1 420
Sand, wet
1 840
Sandstone, broken
1 510
Shale
1 250
Slag, broken
1 750
Stone, crushed
1 600
Topsoil950
Dimensions with Pin-On Bucket
Standard Z-Bar Linkage, with Pin-On General-Purpose Bucket with Bolt-On
Segments and Teeth
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Height to Top of Cab and Canopy
Ground Clearance
Length from Centerline to Front Axle Wheelbase
Dump Clearance •
Height to Hinge Pin, Fully Raised Dump Reach ••
Maximum Digging Depth Overall Length •••
Maximum Rollback at Ground Level
Maximum Rollback, Boom Fully Raised Maximum Bucket Angle, Fully Raised
Overall Bucket Width
Wheel Track
Outside Wheel Width
Full Turn Radius, Inside Full Turn Radius, Outside 3.32 m
0.384 m
1.52 m
3.09 m
2.86 m
3.95 m
1.02 m
0.095 m
7.76 m
37º
50º
45º
2.690 m
2.048 m
2.572 m
6.095 m
4.780 m
Attachment Options
BUCKET OPTONS
Size 2.7 m3
2.7 m3
1.7 m3
1.7 m3
1.8 m3
4.2 m3
4.2 m3
5.5 m3
Type
GP
GP
High Density
High Density
High Density Coal Coal Wood Chip
Blade/Lip
Straight
Straight
Straight
Straight
Spade
Straight
Spade
Straight
Teeth
Bolt-on 2 strap, male adaptors
None
Bolt-on 2 strap, male adaptors
None
None
None
None None
Cutting Edge
Segments
4 Piece Bolt-on
Segments
4 Piece Bolt-on
Weld-on Half Arrows
4 Piece Bolt-on
Weld-on Half Arrows
4 Piece Bolt-on
QUICK ATTACH BUCKETS
Size Type
2.7 m3
GP
5.5 m3
Wood Chip
Blade/Lip
Straight
Straight
Teeth
Bolt-on 2 strap, male adaptors
None
Cutting Edge
Segments
4 Piece Bolt-on
QUICK ATTACH IMPLEMENTS Quick attach pallet fork frame
Quick attach materials handling boom
Quick attch light materials bucket
Quick attach cane grab
LOG GRABS
Load fork log grabs
Large diameter log grab
Sort grapple
Millyard grapple
17
Technical Data - L1806E
engine
Type
John Deere POWERTECHTM 6068H
Non-road emissions standard
Certified to EPA Tier 2 EU Stage II
Cylinders
6 (4 valves per cylinder)
Displacement
6.8 l
Net Peak Power
173 kW @ 1 700 rpm
Net Peak Torque
1 016 Nm @ 1 400 rpm
Fuel System
High Pressure Common Rail
Aspiration
Turbocharged, charge air cooled
Air Cleaner
Dual-element dry type, restriction
indicator in cab monitor for service
Fan Drive
Hydraulically driven, proportionally
controlled, fan aft coolers
Lubrication
Full-flow spin-on filter and integral
cooler
Electrical System
24 volt with 80-amp alternator (100amp alternator optional)
Transmission Fluid with Vertical
Filter
23 l
Travel Speeds
Forward Maximum Gear 1
Gear 2
Gear 3
Gear 4
Bucket Type/Size Capacity, Heaped
3.3 m3
7.6 km/h
12.6 km/h
24.7 km/h
36.6 km/h
Hydraulic Reservoir and Filters
110 l
Park Brake Oil (wet disc)
0.6 l
Capacity, Struck
2.8 m3
Reverse Maximum
Gear 1
Gear 2
Gear 3
Gear 4
7.9 km/h
12.9 km/h
24.9 km/h
NA
axles/brakes
Final Drive
Heavy-duty inboard planetary
Differentials
Hydraulic locking front with
conventional rear
Rear Axle Oscilllation, Stop to
Stop
26o
Brakes
(conform to SAE J1473, ISO3450)
Service Brakes
Hydraulically actuated, inboard
sun-shaft mounted, oil cooled, selfadjusting, single disc
Batteries (2 by 12V)
950 CCA (each)
Parking Brakes
Automatic spring applied,
hydraulically released, driveline
mounted, oil cooled, multi-disc
transmission
Type
Countershaft-type PowerShiftTM
Tyres
Standard Sizes
23.5 x 25, L5, 16 Ply
Torque Converter
Single stage, single phase
Shift Control
Electronically modulated, adaptive,
load and speed dependant
Operator Interface
Joystick-mounted FNR and gear
select lever, kick-down button on
Joystick
standard z-bar pin-on
Type Bucket Information
Standard Z-Bar Linkage, with PinOn General-Purpose Bucket with
Bolt-On, Segments and Teeth
Shift Modes
Manual/auto (1st-4th or 2nd-4th);
quick-shift button with two selectable
modes: kick down or kick up/down;
and three clutch cutoff settings
adjustable on switch pad
Refill capacity
Fuel Tank
(with ground-level fueling)
352 l
Cooling System
29.5 l
Engine Oil with Vertical Spin-on
Filter
24.5 l
Axle Oil (front and rear)
22 l
Hydraulic System/
Steering
Pump (Loader and Steering)
Variable-displacement, axial-piston
pump; closed-center, pressurecompensating system
Maximium Rated Flow
310 l/m @ 6 895 kPa and 2 350 rpm
System Relief Pressure
(Loader and Steering)
25 166 kPa
Loader Controls
Two-function valve; single-dual-lever
controls; control lockout feature;
optional third- and fourth-function
valve with auxiliary lever
Steering (conforms to SAE J1511)
Type
Power, fully hydraulic
Articulation Angle
80º arc (40º each direction)
Hydraulic Cycle Times Standard
Z-Bar
Raise
5.5 sec
Bucket Weight 1 738 kg
Bucket Width 3.05 m
Breakout Force
15 577 kg
Tipping Load, Straight
15 230 kg
Tipping Load, 40o Full Turn
13 126 kg
Safe Operating Load
6 563 kg
Reach, 45o Dump, Clearance
(2.13 m)
1.61 m
Reach, 45o Dump, Full Height
•• 1.06 m
Dump Clearance, 45o, Full Height
• 2.91 m
Overall Length, Bucket on Ground
••• 8.10 m
Dump
1.4 sec
Loader Clearance Circle, Bucket
Carry Position
13.20 m
Lower (float down)
3.0 sec
Operating Weight
18 160 kg
Total
9.9 sec
Turning Radius (measured to
centerline of outside tyre)
5.57 m
Material
Loose Material
kg/m3
Caliche
1 250
Cinders590
Clay and gravel, dry
1 420
Clay and gravel, wet
1 540
Clay, dry
1 480
Clay, natural bed
1 660
Clay, wet
1 660
Coal, anthracite, broken
1 100
Coal, bituminous, broken
830
Earth, dry, packed
1 510
Earth, loam
1 250
18
Earth, wet, excavated
Granite, broken or large crushed
Gravel, dry
Gravel, dry 13 to 50 mm
Gravel, pit run (graveled sand)
Gravel, wet 13 to 50 mm
Gypsum, crushed
Limestone, broken or crushed
Magnetite, iron ore
Phosphate rock
Pyrite, iron ore
kg/m3
kg/m3
1 600
1 660
1 510
1 690
1 930
2 020
1 600
1 540
2 790
1 280
2 580
Sand and gravel, dry
1 720
Sand and gravel, wet
2 020
Sand, dry
1 420
Sand, wet
1 840
Sandstone, broken
1 510
Shale
1 250
Slag, broken
1 750
Stone, crushed
1 600
Topsoil950
Dimensions with Pin-On Bucket
Standard Z-Bar Linkage, with Pin-On General-Purpose Bucket with Bolt-On
Segments and Teeth
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Height to Top of Cab and Canopy
Ground Clearance
Length from Centerline to Front Axle Wheelbase
Dump Clearance •
Height to Hinge Pin, Fully Raised Dump Reach ••
Maximum Digging Depth Overall Length •••
Maximum Rollback at Ground Level
Maximum Rollback, Boom Fully Raised Maximum Bucket Angle, Fully Raised
Overall Bucket Width
Wheel Track
Outside Wheel Width
Full Turn Radius, Inside Full Turn Radius, Outside 3.43 m
0.461 m
1.60 m
3.26 m
2.91 m
4.12 m
1.06 m
0.106 m
8.10 m
40º
55º
50º
2.900 m
2.143 m
2.705 m
5.179 m
6.580 m
Attachment Options
BUCKET OPTONS
Size 3.3 m3
3.3 m3
2 m3
2 m3
2.2 m3
2.9 m3
2.9 m3
4 m3
4.9 m3
9 m3
Type
GP
GP
High Density
High Density
High Density Rock Rock Low Density
Coal
Wood Chip
Blade/Lip
Straight
Straight
Straight
Straight
Spade
Spade
Spade
Straight
Spade
Straight
Teeth
Bolt-on 2 strap, male adaptors
None
Bolt-on 2 strap, male adaptors
None
None
Bolt-on 2 strap, male adaptors
None None
None
None
Cutting Edge
Segments
4 Piece Bolt-on
Segments
4 Piece Bolt-on
Weld-on Half Arrows
Segments
Weld-on Half Arrows
4 Piece Bolt-on
4 Piece Bolt-on
4 Piece Bolt-on
QUICK ATTACH BUCKETS
Size Type
2.2 m3
High Density
3.3 m3
GP Bucket
4.9 m3
Coal
Blade/Lip
Spade
Straight
Straight
Teeth
None
Bolt-on 2 strap, male adaptors
None
Cutting Edge
Weld-on Half Arrows
Segments
4 Piece Bolt-on
QUICK ATTACH IMPLEMENTS Quick attach pallet fork frame
Quick attach cane grab
LOG GRABS
Load fork log grabs
Large diameter log grab
Sorting grapple
Millyard grapple
19
Technical Data - L2106E
engine
Type
John Deere POWERTECHTM 6090H
Non-road emissions standard
Certified to EPA Tier 2 EU Stage II
Cylinders
6 (4 valves per cylinder)
Displacement
9.0 l
Net Peak Power
197 kW @ 1 800 rpm
Net Peak Torque
1 159 Nm @ 1 300 rpm
Fuel System
High Pressure Common Rail
Aspiration
Turbocharged, charge air cooled
Air Cleaner
Dual-element dry type, restriction
indicator in cab monitor for service
Fan Drive
Hydraulically driven, proportionally
controlled, fan aft coolers
Lubrication
Full-flow spin-on filter and integral
cooler
Electrical System
24 volt with 80-amp alternator (100amp alternator optional)
Transmission Fluid with Vertical
Filter
24 l
Travel Speeds
Forward Maximum Gear 1
Gear 2
Gear 3
Gear 4
Bucket Type/Size Capacity, Heaped
3.6 m3
7.2 km/h
11.9 km/h
23.1 km/h
35.6 km/h
Hydraulic Reservoir and Filters
110 l
Park Brake Oil (wet disc)
0.6 l
Capacity, Struck
3.2 m3
Reverse Maximum
Gear 1
Gear 2
Gear 3
Gear 4
7.6 km/h
12.5 km/h
24.2 km/h
NA
axles/brakes
Final Drive
Heavy-duty inboard planetary
Differentials
Hydraulic locking front with
conventional rear
Rear Axle Oscilllation, Stop to
Stop
26o
Brakes
(conform to SAE J1473, ISO3450)
Service Brakes
Hydraulically actuated, inboard
sun-gear mounted, oil cooled, selfadjusting, single disc
Batteries (2 by 12V)
1 400 CCA (each)
Parking Brakes
Automatic spring applied,
hydraulically released, driveline
mounted, oil cooled, multi-disc
transmission
Type
Countershaft-type PowerShiftTM
Tyres
Standard Sizes
23.5 x 25, L5, 16 Ply
Torque Converter
Single stage, single phase
Shift Control
Electronically modulated, adaptive,
load and speed dependant
Operator Interface
Joystick-mounted FNR and gear
select lever, kick-down button on
Joystick
standard z-bar pin-on
Type Bucket Information
Standard Z-Bar Linkage, with PinOn General-Purpose Bucket with
Bolt-On, Segments and Teeth
Shift Modes
Manual/auto (1st-4th or 2nd-4th);
quick-shift button with two selectable
modes: kick down or kick up/down;
and three clutch cutoff settings
adjustable on switch pad
Refill capacity
Fuel Tank
(with ground-level fueling)
352 l
Cooling System
34 l
Engine Oil with Vertical Spin-on
Filter
28 l
Axle Oil (front and rear)
22 l
Hydraulic System/
Steering
Pump (Loader and Steering)
Variable-displacement, axial-piston
pump; closed-center, pressurecompensating system
Maximium Rated Flow
310 l/m @ 6 895 kPa and 2 350 rpm
System Relief Pressure
(Loader and Steering)
25 166 kPa
Loader Controls
Two-function valve; single-dual-lever
controls; control lockout feature;
optional third- and fourth-function
valve with auxiliary lever
Steering (conforms to SAE J1511)
Type
Power, fully hydraulic
Articulation Angle
80º arc (40º each direction)
Hydraulic Cycle Times Standard
Z-Bar
Raise
5.5 sec
Bucket Weight 1 816 kg
Bucket Width 3.05 m
Breakout Force
14 445 kg
Tipping Load, Straight
16 489kg
Tipping Load, 40o Full Turn
14 204 kg
Safe Operating Load
7 102 kg
Reach, 45o Dump, Clearance
(2.13 m)
1.67 m
Reach, 45o Dump, Full Height
•• 1.06 m
Dump Clearance, 45o, Full Height
• 2.91 m
Overall Length, Bucket on Ground
••• 8.31 m
Dump
1.2 sec
Loader Clearance Circle, Bucket
Carry Position
13.25 m
Lower (float down)
3.0 sec
Operating Weight
19 130 kg
Total
9.7 sec
Turning Radius (measured to
centerline of outside tyre)
5.64 m
Material
Loose Material
kg/m3
Caliche
1 250
Cinders590
Clay and gravel, dry
1 420
Clay and gravel, wet
1 540
Clay, dry
1 480
Clay, natural bed
1 660
Clay, wet
1 660
Coal, anthracite, broken
1 100
Coal, bituminous, broken
830
Earth, dry, packed
1 510
Earth, loam
1 250
20
Earth, wet, excavated
Granite, broken or large crushed
Gravel, dry
Gravel, dry 13 to 50 mm
Gravel, pit run (graveled sand)
Gravel, wet 13 to 50 mm
Gypsum, crushed
Limestone, broken or crushed
Magnetite, iron ore
Phosphate rock
Pyrite, iron ore
kg/m3
kg/m3
1 600
1 660
1 510
1 690
1 930
2 020
1 600
1 540
2 790
1 280
2 580
Sand and gravel, dry
1 720
Sand and gravel, wet
2 020
Sand, dry
1 420
Sand, wet
1 840
Sandstone, broken
1 510
Shale
1 250
Slag, broken
1 750
Stone, crushed
1 600
Topsoil950
Dimensions with Pin-On Bucket
Standard Z-Bar Linkage, with Pin-On General-Purpose Bucket with Bolt-On
Segments and Teeth
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Height to Top of Cab and Canopy
Ground Clearance
Length from Centerline to Front Axle Wheelbase
Dump Clearance •
Height to Hinge Pin, Fully Raised Dump Reach ••
Maximum Digging Depth Overall Length •••
Maximum Rollback at Ground Level
Maximum Rollback, Boom Fully Raised Maximum Bucket Angle, Fully Raised
Overall Bucket Width
Wheel Track
Outside Wheel Width
Full Turn Radius, Inside Full Turn Radius, Outside 3.43 m
0.461 m
1.60 m
3.26 m
2.91 m
4.12 m
1.06 m
0.123 m
8.31 m
40.6º
55.1º
50.1º
3.400 m
2.150 m
2.712 m
5.147 m
6.585 m
Attachment Options
BUCKET OPTONS
Size 3.6 m3
3.6 m3
2.2 m3
2.2 m3
2.4 m3
2.4 m3
2.9 m3
3.1 m3
3.1 m3
5.3 m3
Type
GP
GP
High Density
High Density
High Density High Density
High Density
Rock
Rock
Coal
Blade/Lip
Straight
Straight
Straight
Straight
Spade
Spade
Straight
Spade
Spade
Straight
Teeth
Bolt-on 2 strap, male adaptors
None
Bolt-on 2 strap, male adaptors
None
None
None
None Bolt-on 2 strap, male adaptors
None
None
Cutting Edge
Segments
4 Piece Bolt-on
Segments
4 Piece Bolt-on
Weld-on Half Arrows
3 Piece Bolt-on
4 Piece Bolt-on
Segments
Weld-on Half Arrows
4 Piece Bolt-on
QUICK ATTACH BUCKETS
Size Type
3.6 m3
GP
5.3 m3
Coal
Blade/Lip
Straight
Straight
Teeth
Bolt-on 2 strap, male adaptors
None
Cutting Edge
Segments
4 Piece Bolt-on
IMPLEMENTS
Cane grab
LOG GRABS
Load fork log grabs
Large diameter log grab
Sorting grapple
Millyard grapple
21
Technical Data - L2606E
engine
Type
John Deere POWERTECHTM 6090H
Non-road emissions standard
Certified to EPA Tier 2 EU Stage II
Cylinders
6 (4 valves per cylinder)
Displacement
9.0 l
Net Peak Power
227 kW @ 1 500 rpm
Net Peak Torque
1 456 Nm @ 1 400 rpm
Fuel System
High Pressure Common Rail
standard z-bar pin-on
Type Bucket Information
Standard Z-Bar Linkage, with PinOn General-Purpose Bucket with
Bolt-On, Segments and Teeth
Shift Modes
Manual/auto (1st-4th or 2nd-4th);
quick-shift button with two selectable
modes: kick down or kick up/down;
and three clutch cutoff settings
adjustable on switch pad
Transmission Fluid with Vertical
Filter
27.9 l
Travel Speeds
Forward Max (5-speed Transmission) Gear 1
8.4 km/h
Gear 2
15.2 km/h
Gear 3
23.6 km/h
Gear 4
34.6 km/h
Gear 5
40 km/h
Reverse Maximum
Gear 1
8.4 km/h
Gear 2
14.0 km/h
Gear 3
34.6 km/h
Gear 4
NA
Gear 5
NA
Hydraulic Reservoir and Filters
159 l
Bucket Type/Size Capacity, Heaped
4.4 m3
Park Brake Oil (wet disc)
0.67 l
Capacity, Struck
3.7 m3
Axle Oil (front and rear)
46 l
Hydraulic System/
Steering
Pump (Loader and Steering)
Two variable-displacement, loadsensing axial-piston pumps, closedcenter system
Maximium Rated Flow
515 l/m @ 6 895 kPa and 2 350 rpm
Bucket Weight 2 469 kg
Bucket Width 3.2 m
Breakout Force
19 515 kg
Aspiration
Turbocharged, charge air cooled
axles/brakes
Final Drive
Heavy-duty inboard planetary
Air Cleaner
Dual-element dry type, restriction
indicator in cab monitor for service
Differentials
Hydraulic locking front with
conventional rear
Fan Drive
Hydraulically driven, proportionally
controlled, fan aft coolers
Rear Axle Oscilllation, Stop to
Stop
26o
Lubrication
Full-flow spin-on filter and integral
cooler
Brakes
(conform to SAE J1473, ISO3450)
Service Brakes
Hydraulically actuated, inboard
sun-gear mounted, oil cooled, selfadjusting, single disc
Steering (conforms to SAE J1511)
Type
Power, fully hydraulic
Parking Brakes
Automatic spring applied,
hydraulically released, driveline
mounted, oil cooled, multi-disc
Hydraulic Cycle Times Standard
Z-Bar
Raise
5.9 sec
Tyres
Standard Sizes
26.5 x 25, L5, 20 Ply
Dump
1.4 sec
Loader Clearance Circle, Bucket
Carry Position
14.38 m
Lower (float down)
2.8 sec
Operating Weight
24 182 kg
Electrical System
24 volt with 80-amp alternator (100amp alternator optional)
Batteries (2 by 12V)
1 400 CCA (each)
transmission
Type
Countershaft-type PowerShiftTM
Torque Converter
Single stage, single phase
Shift Control
Electronically modulated, adaptive,
load and speed dependant
Operator Interface
Joystick-mounted FNR and gear
select lever, kick-down button on
Joystick
Refill capacity
Fuel Tank
(with ground-level fueling)
469 l
Cooling System
45 l
Engine Oil with Vertical Spin-on
Filter
34 l
System Relief Pressure
(Loader and Steering)
22 670 kPa
Loader Controls
Two-function valve; single-dual-lever
controls; control lockout feature;
optional third- and fourth-function
valve with auxiliary lever
Articulation Angle
80º arc (40º each direction)
Tipping Load, Straight
19 923 kg
Tipping Load, 40o Full Turn
17 123 kg
Safe Operating Load
8 473 kg
Reach, 45o Dump, Clearance
(2.13 m)
1.85 m
Reach, 45o Dump, Full Height
•• 1.23 m
Dump Clearance, 45o, Full Height
• 3.04 m
Overall Length, Bucket on Ground
••• 9.01 m
Total
10.1 sec
Turning Radius (measured to
centerline of outside tyre)
6.28 m
Material
Loose Material
kg/m3
Caliche
1 250
Cinders590
Clay and gravel, dry
1 420
Clay and gravel, wet
1 540
Clay, dry
1 480
Clay, natural bed
1 660
Clay, wet
1 660
Coal, anthracite, broken
1 100
Coal, bituminous, broken
830
Earth, dry, packed
1 510
Earth, loam
1 250
22
Earth, wet, excavated
Granite, broken or large crushed
Gravel, dry
Gravel, dry 13 to 50 mm
Gravel, pit run (graveled sand)
Gravel, wet 13 to 50 mm
Gypsum, crushed
Limestone, broken or crushed
Magnetite, iron ore
Phosphate rock
Pyrite, iron ore
kg/m3
kg/m3
1 600
1 660
1 510
1 690
1 930
2 020
1 600
1 540
2 790
1 280
2 580
Sand and gravel, dry
1 720
Sand and gravel, wet
2 020
Sand, dry
1 420
Sand, wet
1 840
Sandstone, broken
1 510
Shale
1 250
Slag, broken
1 750
Stone, crushed
1 600
Topsoil950
Dimensions with Pin-On Bucket
Standard Z-Bar Linkage, with Pin-On General-Purpose Bucket with Bolt-On
Segments and Teeth
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Height to Top of Cab and Canopy
Ground Clearance
Length from Centerline to Front Axle Wheelbase
Dump Clearance •
Height to Hinge Pin, Fully Raised Dump Reach ••
Maximum Digging Depth Overall Length •••
Maximum Rollback at Ground Level
Maximum Rollback, Boom Fully Raised Maximum Bucket Angle, Fully Raised
Overall Bucket Width
Wheel Track
Outside Wheel Width
Full Turn Radius, Inside Full Turn Radius, Outside 3.53 m
0.462 m
1.70 m
3.46 m
3.04 m
4.29 m
1.23 m
0.080 m
9.01 m
39.5º
54.01º
49.4º
3.040 m
2.209 m
2.877 m
5.326 m
6.805 m
Attachment Options
BUCKET OPTONS
Size 4.4 m3
4.4 m3
2.7 m3
2.7 m3
2.9 m3
3.9 m3
3.9 m3
6.5 m3
Type
GP
GP
High Density
High Density
High Density Rock
Rock
Coal
Blade/Lip
Straight
Straight
Straight
Straight
Spade
Spade
Spade
Straight
IMPLEMENTS
Cane grab
LOG GRABS
Large diameter log grab
Sorting grapple
Millyard grapple
Teeth
Bolt-on 2 strap, male adaptors
None
Bolt-on 2 strap, male adaptors
None
None
Bolt-on 2 strap, male adaptors
None None
Cutting Edge
Segments
4 Piece Bolt-on
Segments
4 Piece Bolt-on
Weld-on Half Arrows
Segments
4 Piece Bolt-on
4 Piece Bolt-on
23
Technical Data - L2706E
engine
Type
John Deere POWERTECHTM 6135H
Non-road emissions standard
Certified to EPA Tier 2 EU Stage II
Cylinders
6 (4 valves per cylinder)
Displacement
13.5 l
Net Peak Power
248 kW @ 1 600 rpm
Net Peak Torque
1 619 Nm @ 900 rpm
Fuel System
Mechanically actuated electronic
injectors
Aspiration
Turbocharged, charge air cooled
Air Cleaner
Dual-element dry type, restriction
indicator in cab monitor for service
Fan Drive
Hydraulically driven, proportionally
controlled, fan aft coolers
standard z-bar pin-on
Type Bucket Information
Standard Z-Bar Linkage, with PinOn General-Purpose Bucket with
Bolt-On, Segments and Teeth
Shift Modes
Manual/auto (1st-4th or 2nd-4th);
quick-shift button with two selectable
modes: kick down or kick up/down;
and three clutch cutoff settings
adjustable on switch pad
Transmission Fluid with Vertical
Filter
28 l
Travel Speeds
Forward Max (5-speed Transmission) Gear 1
8.3 km/h
Gear 2
14.9 km/h
Gear 3
23.1 km/h
Gear 4
33.9 km/h
Gear 5
40.0 km/h
Reverse Maximum
Gear 1
8.3 km/h
Gear 2
14.0 km/h
Gear 3
33.9 km/h
Gear 4
NA
Gear 5
NA
Hydraulic Reservoir and Filters
159 l
Bucket Type/Size Capacity, Heaped
4.7 m3
Park Brake Oil (wet disc)
0.7 l
Capacity, Struck
4.0 m3
axles/brakes
Final Drive
Heavy-duty inboard planetary
Differentials
Hydraulic locking front with
conventional rear
Rear Axle Oscilllation, Stop to
Stop
26o
Axle Oil (front and rear)
46 l
Hydraulic System/
Steering
Pump (Loader and Steering)
Two variable-displacement, loadsensing axial-piston pumps, closedcenter system
Maximium Rated Flow
513 l/m @ 6 895 kPa and 2 350 rpm
System Relief Pressure
(Loader and Steering)
25 166 kPa
Loader Controls
Two-function valve; single-dual-lever
controls; control lockout feature;
optional third- and fourth-function
valve with auxiliary lever
Bucket Weight 2 579 kg
Bucket Width 3.27 m
Breakout Force
18 905 kg
Tipping Load, Straight
20 508 kg
Tipping Load, 40o Full Turn
17 588 kg
Safe Operating Load
8 794 kg
Reach, 45o Dump, Clearance
(2.13 m)
2.05 m
Brakes
(conform to SAE J1473, ISO3450)
Service Brakes
Hydraulically actuated, inboard
sun-gear mounted, oil cooled, selfadjusting, single disc
Steering (conforms to SAE J1511)
Type
Power, fully hydraulic
Batteries (2 by 12V)
1 400 CCA (each)
Parking Brakes
Automatic spring applied,
hydraulically released, driveline
mounted, oil cooled, multi-disc
Hydraulic Cycle Times Standard
Z-Bar
Raise
5.9 sec
transmission
Type
Countershaft-type PowerShiftTM
Tyres
Standard Sizes
26.5 x 25, L5, 20 Ply
Dump
1.3 sec
Loader Clearance Circle, Bucket
Carry Position
14.60 m
Torque Converter
Single stage, single phase
Refill capacity
Fuel Tank
(with ground-level fueling)
469 l
Lower (float down)
2.5 sec
Operating Weight
26 210 kg
Lubrication
Full-flow spin-on filter and integral
cooler
Electrical System
24 volt with 80-amp alternator (100amp alternator optional)
Shift Control
Electronically modulated, adaptive,
load and speed dependant
Operator Interface
Joystick-mounted FNR and gear
select lever, kick-down button on
Joystick
Cooling System
47 l
Engine Oil with Vertical Spin-on
Filter
38 l
Articulation Angle
80º arc (40º each direction)
Reach, 45o Dump, Full Height
•• 1.28 m
Dump Clearance, 45o, Full Height
• 3.19 m
Overall Length, Bucket on Ground
••• 9.26 m
Total
9.7 sec
Turning Radius (measured to
centerline of outside tyre)
6.32 m
Material
Loose Material
kg/m3
Caliche
1 250
Cinders590
Clay and gravel, dry
1 420
Clay and gravel, wet
1 540
Clay, dry
1 480
Clay, natural bed
1 660
Clay, wet
1 660
Coal, anthracite, broken
1 100
Coal, bituminous, broken
830
Earth, dry, packed
1 510
Earth, loam
1 250
24
Earth, wet, excavated
Granite, broken or large crushed
Gravel, dry
Gravel, dry 13 to 50 mm
Gravel, pit run (graveled sand)
Gravel, wet 13 to 50 mm
Gypsum, crushed
Limestone, broken or crushed
Magnetite, iron ore
Phosphate rock
Pyrite, iron ore
kg/m3
kg/m3
1 600
1 660
1 510
1 690
1 930
2 020
1 600
1 540
2 790
1 280
2 580
Sand and gravel, dry
1 720
Sand and gravel, wet
2 020
Sand, dry
1 420
Sand, wet
1 840
Sandstone, broken
1 510
Shale
1 250
Slag, broken
1 750
Stone, crushed
1 600
Topsoil950
Dimensions with Pin-On Bucket
Standard Z-Bar Linkage, with Pin-On General-Purpose Bucket with Bolt-On
Segments and Teeth
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Height to Top of Cab and Canopy
Ground Clearance
Length from Centerline to Front Axle Wheelbase
Dump Clearance •
Height to Hinge Pin, Fully Raised Dump Reach ••
Maximum Digging Depth Overall Length •••
Maximum Rollback at Ground Level
Maximum Rollback, Boom Fully Raised Maximum Bucket Angle, Fully Raised
Overall Bucket Width
Wheel Track
Outside Wheel Width
Full Turn Radius, Inside Full Turn Radius, Outside 3.50 m
0.462 m
1.70 m
3.46 m
3.19 m
4.50 m
1.28 m
0.115 m
9.26 m
45.5º
52º
44.1º
3.275 m
2.291 m
2.953 m
5.743 m
7.300 m
Attachment Options
BUCKET OPTONS
Size 4.7 m3
4.7 m3
2.8 m3
2.8 m3
3 m3
4 m3
4 m3
6.8 m3
Type
GP
GP
High Density
High Density
High Density Rock
Rock
Coal
Blade/Lip
Straight
Straight
Straight
Straight
Spade
Spade
Spade
Straight
CANE GRABS
Cane grab
LOG GRABS
Large diameter log grab
Sorting grapple
Millyard grapple
Teeth
Bolt-on 2 strap, male adaptors
None
Bolt-on 2 strap, male adaptors
None
None
Bolt-on 2 strap, male adaptors
None None
Cutting Edge
Segments
4 Piece Bolt-on
Segments
4 Piece Bolt-on
Weld-on Half Arrows
Segments
Weld-on Half Arrows
4 Piece Bolt-on
25
Notes
26
Notes
27
BELL INTERNATIONAL: Tel: +27 (0) 35-907 9431
E-mail: marketing@bellequipment.com
Tel: +61 (0) 8-9356-1033
Tel: +49 (0) 6631 / 91-13-0
Tel: +27 (0) 11-928-9700
Tel: +44 (0) 1283-712862
Web: www.bellequipment.com
Tel: +33 (0) 5-55-89-23-56
Tel: +7-495-287-80-02
Tel: +34-91-879-60-19
Tel: +1-855-494-2355
BROCH/1421/09/13 E-series Front End Loader ENGLISH
All dimensions are shown in millimetres, unless otherwise stated between brackets.
Under our policy of continuous improvement, we reserve the right to change specifications and
design without prior notice. Photographs featured in this brochure may include
optional equipment.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising