5055.201 SUPER-SD1 071111

5055.201 SUPER-SD1 071111
IMPORTANT:
THESE INSTRUCTIONS ARE TO
REMAIN WITH THE HOMEOWNER
SAFETY NOTICE
If this stove is not properly installed, a
house fire may result. For your safety,
follow the installation instructions. Contact
local building or fire officials about
restrictions and installation inspection
requirements in your area.
INSTALLATION
A N D O P E R AT I N G
INSTRUCTIONS
TESTED and LISTED to CAN/ULC S627
AND UL 1482
Meets the Environmental Protection
Agency's July 1990 Particulate Emission
Standards
MODEL - SUPER 27
SPECTRUM
SPECTRUM CLASSIC
DESIGN-D
071111-20
SUPER-SD1
5055.201
Contents
Safety and Maintenance ...................................................................................... 3
Creosote ............................................................................................................... 4
Formation and Need for Removal ....................................................................................... 4
Chimney Fires..................................................................................................................... 4
In Case of a Chimney Fire .................................................................................................. 4
Avoiding a Chimney Fire ..................................................................................................... 4
Assembly .............................................................................................................. 5
Crate Removal .................................................................................................................... 5
Optional Ash Cleanout System -(Install first) ...................................................................... 5
Pedestal Kit......................................................................................................................... 5
Leg Kit ................................................................................................................................ 5
Mobile Home Installation .................................................................................... 6
Clearances ......................................................................................................................... 6
Procedure:........................................................................................................................... 6
Listed Chimney and Chimney Connector ........................................................................... 7
Residential Installation ....................................................................................... 8
Clearances ......................................................................................................................... 8
Chimney and Connector ..................................................................................................... 8
Double-Wall Connector ....................................................................................................... 8
Single-Wall Connector ........................................................................................................ 8
Procedure ........................................................................................................................... 8
Floor Protector ..................................................................................................... 9
Combustion Air .................................................................................................... 9
Operation............................................................................................................ 10
Over Firing ........................................................................................................................ 10
Wood Selection................................................................................................................. 10
How to Test Your Wood ..................................................................................................... 10
Lighting for the First Time ................................................................................................. 10
Lighting a Fire ................................................................................................................... 10
Normal Operation ............................................................................................................. 10
Restarting After Extended or Overnight Burns.................................................................. 11
More Wood, More Heat..................................................................................................... 11
Proper Draft ...................................................................................................................... 11
Ash Removal .................................................................................................................... 11
Disposal of Ashes ............................................................................................................. 11
Baffle Removal ................................................................................................... 11
Removal............................................................................................................................ 11
Optional Blower ................................................................................................. 12
Blower Operation .............................................................................................................. 12
Optional Outside Air Adaptor ............................................................................................ 12
Appendix A ......................................................................................................... 13
Troubleshooting ................................................................................................................ 13
Replacement Parts - Super 27 ......................................................................................... 14
Replacement Parts - Spectrum and Spectrum Classic .................................................... 15
Understanding & Operating Your Pacific Energy Stove..................................................... 16
Pedestal or Legs Installation Instructions ......................................................................... 17
NOTES ................................................................................................................ 18
Label ................................................................................................................................. 19
PLEASE SAVE THESE INSTRUCTIONS
NOTE: WE STRONGLY RECOMMEND THAT SMOKE DETECTORS BE INSTALLED.
If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may
be due to curing of stove paint or fumes caused by accidentally leaving the fire door open. Do not disconnect the
detectors. If necessary, relocate them to reduce their sensitivity.
SAFETY NOTICE: If this stove is not properly installed, a house fire may result. For your safety, follow the
installation instructions. Contact local building or fire officials about restrictions and installation inspection
requirements in you area.
Please read this entire manual before you install and use your new room heater. Failure to follow instructions may
result in property damage, bodily injury, or even death.
2
SUPER-SD1
071111-20
Safety and
Maintenance
1. Burn wood only, dry and well seasoned. The denser or
heavier the wood when dry, the greater its heat value.
This is why hardwoods are generally preferred. Green
or wet wood will cause a rapid buildup of creosote.
If you feel it is necessary to burn wet or unseasoned
wood, do so only with the air inlet set open enough
to maintain a good strong fire and fairly high chimney
temperatures. Do not attempt to burn overnight using
green wood or wet wood. Wet wood can cause up
to 25% drop in heater output, as well as contributing
significantly to creosote buildup.
WARNING: Never use chemicals or any other
volatile liquid to start a fire. Do not burn garbage,
or flammable fluids such as gasoline, naptha, or
engine oil. We strongly recommend that smoke
detectors be installed.
2. Remove ashes frequently. Embers can roll out the
door and create a fire hazard. Maintain a 1" minimum
ash base.
3. If glass becomes darkened through slow burning or
poor wood, it can readily be cleaned with fireplace
glass cleaner when stove is cold. Never scrape with
an object that might scratch the glass. The type and
amount of deposit on the glass is a good indication
of the flue pipe and chimney buildup. A light brown
dusty deposit that is easily wiped off usually indicates
good combustion and dry, well-seasoned wood and
therefore relatively clean pipes and chimney. On the
other hand, a black greasy deposit that is difficult to
remove is a result of wet and green wood and too
slow a burning rate. This heavy deposit is building
up at least as quickly in the chimney.
WARNING: ONLY USE MATERIALS SUPPLIED BY
MANUFACTURER WHEN DOING MAINTENANCE
OR REPLACEMENTS.
4. DOOR GASKETS - The gasket used by Pacific Energy
(7/8" medium density fiberglass rope) requires only
light pressure to seal. This will prolong seal life. It is
important that the door seal be maintained in good
condition. Periodically inspect seals and replace if
necessary. Follow instructions included in the DR31.
WDGKIT kit obtainable from your nearest Pacific
Energy dealer.
5. DOOR GLASS - Do not slam loading door or otherwise
impact glass. When closing door, make sure that no
logs protrude to impact the glass. If the glass gets
cracked or broken, it must be replaced before using the stove. Replacement glass can be obtained
from your dealer. Use 8-13/16" x 15-1/4" x 5 mm.
Ceramic glass only. Do not substitute with any
other type.
071111-20
To remove broken glass, undo the four retaining screws
and remove clamps and frame, noting position for reassembly. Remove all particles of glass . Be careful as
they are very sharp. Install new glass complete with
gasket. Replace frame, clamps and screws.
CAUTION:
- do not overtighten, tighten screws very carefully
- do not clean glass when hot
- do not use abrasive cleaners on glass
6. The area where boost combustion air enters the
firebox must be kept clear of excessive ash buildup
which will block air flow. This area is at the front of
the firebox.
7. Do not store wood within heater installation clearances,
or within the space required for fuel loading and ash
removal. Keep the area around the heater clean and
free of loose combustibles, furniture, newspapers,
etc.
8. If gold door requires cleaning, use mild soap and
water only. Use of abrasive cleaners will void warranty.
9. Establish a routine for the fuel, woodburning and firing technique. Check daily for creosote buildup until
experience shows how often you need to clean to be
safe.
10. Be aware that the hotter the fire, the less creosote
is deposited. Weekly cleaning may be necessary in
mild weather, even though monthly cleaning is usually
enough in the coldest months when burning rates are
higher.
11. Instruct all members of your family on the safe
operation of the heater. Ensure they have enough
knowledge of the entire system if they are expected
to operate it. Stress the section on chimney fires
and the importance of following the steps outlined
"In Case of Chimney Fire".
SUPER-SD1
3
Creosote
Formation and Need for Removal
When wood is burned slowly, it produces tar and other
organic vapours, which combine with expelled moisture
to form creosote. The creosote vapours condense in the
relatively cool chimney flue of a slow burning fire. As a
result, creosote residue accumulates on the flue lining.
When ignited, this creosote makes an extremely hot fire.
The chimney connector and chimney should be inspected
periodically (at least once every two months) during the
heating season to determine if a creosote buildup has
occurred. If creosote has accumulated (3 mm. or more), it
should be removed to reduce the risk of a chimney fire.
1. Highest smoke densities occur when a large amount of
wood is added to a bed of hot coals and the air inlet is
closed. The heated wood generates smoke, but without
ample air, the smoke cannot burn. Smoke-free, clean
burning requires small fuel loads, two or three logs at
a time or 1/4 to 1/2 of fuel load and leaving the air inlet
relatively wide open, especially during the first 10 to 30
minutes after each loading, when most of the smoke
generating reactions are occurring. After 30 minutes
or so, the air inlet can be turned down substantially
without excessive smoke generation. Wood coals
create very little creosote-producing smoke.
2. The cooler the surface over which the wood smoke is
passing, the more creosote will be condensed. Wet
or green wood contributes significantly to creosote
formation as the excess moisture that is boiled off
cools the fire, making it difficult for the tars and gases
to ignite, thus creating dense smoke and poor combustion. This moisture-laden smoke cools the chimney,
compounding the problem by offering the smoke the
ideal place to condense.
In summary, a certain amount of creosote is inevitable
and must be lived with. Regular inspection and cleaning is the solution. The use of dry, seasoned wood
and ample combustion air will help to minimize the
buildup.
-Flames and sparks shooting out of the top of the
chimney
-A roaring sound
-Vibration of the chimney
In Case of a Chimney Fire
1. Prepare to evacuate to ensure everyone's safety. Have
a well understood plan of action for evacuation. Have
a place outside where everyone is to meet.
2. Close air inlet on stove.
3. Call local fire department. Have a fire extinguisher
handy. Contact your local municipal or provincial fire
authority for further information on how to handle a
chimney fire. It is most important that you have a
clearly understood plan on how to handle a chimney
fire.
4. After the chimney fire is out, the chimney must be
cleaned and checked for stress and cracks before
starting another fire. Also check combustibles around
the chimney and the roof.
- The services of a competent or certified installer, (certified
by the Wood Energy Technical Training program (WETT)
- in Canada, Hearth Education Foundation (HEARTH) - in
U.S.A.,) are strongly recommended.
Avoiding a Chimney Fire
There are two ways to avoid chimney fires:
1. Do not let creosote build up to a point where a big
chimney fire is possible.
2. Do not have fires in the heater that may ignite chimney fires. These are hot fires, such as when burning
household trash, cardboard, Christmas tree limbs,
or even ordinary fuel wood; (e.g.. with a full load on
a hot bed of coals and with the air inlet excessively
open.)
Chimney Fires
The result of excessive creosote buildup is a chimney fire.
Chimney fires are dangerous. Chimney inside temperatures can exceed 2000° F. This causes much higher than
normal temperatures in the chimney and on its exterior
surfaces. Thus ignition of nearby or touching combustible material is more likely during a chimney fire. Proper
clearances are critical during such a fire.
Chimney fires are easy to detect; they usually involve one
or more of the following:
4
SUPER-SD1
071111-20
Super 27 - Pedestal Model
Spectrum
Super 27 - Leg Model
Spectrum Classic
Assembly - Super 27 only Crate Removal
1) Carefully remove wood top and supports.
2) Remove plastic cover.
3) Using a 7/16" wrench, remove lag bolts that secure
stove body to bottom pallet.
4) Place stove body carefully on its back.
5) Using two 3/4" wrench, remove 1" x 1/2" bolts and
save for later use.
6) Remove pallet retaining brackets from stove bottom.
Optional Ash Cleanout System -(Install
first)
2) Secure in place with 1" x 1/2" bolts previously removed.
3) Carefully place the unit in the upright position.
Leg Kit
1) With the unit on its back, align the ash drawer enclosure mounting holes (removable cover facing up) with
the holes on the stove.
2) Position the legs over top of the same holes on the
stove.
2) Secure in place with 1" x 1/2" bolts previously removed.
3) Carefully place the unit in the upright position.
1) With stove body laying on its back, remove the ash
system hole cover and gasket located under the stove.
Discard cover plate and gasket.
2) Inside the stove, remove the two bolts for the ash dump
from the firebox bottom and insert into the brick retainer
with the flanges on the the brick retainer pointed away
from the threads on the bolts.
3) Replace bolts with brick retainer in the firebox
bottom.
4) Place new gasket provided over existing bolts.
5) Install ash dump system over gasket and secure with
two nuts previously removed.
Pedestal Kit
1) With the unit on its back and the removable cover
facing up, align the pedestal mounting holes with the
holes on the stove.\
071111-20
SUPER-SD1
5
Procedure:
Mobile Home
Installation
Warning: Under no circumstances is this heater to be
installed in a makeshift or "temporary" manner. It may be
fired only after the following conditions have been met.
- DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVING ANOTHER APPLIANCE.
- DO NOT INSTALL IN A SLEEPING ROOM.
- Outside air supply must be used for Mobile Home installations see Figure #2, Page 7.
- The services of a competent or certified installer, (certified
by the Wood Energy Technical Training program (WETT)
- in Canada, Hearth Education Foundation (HEARTH) - in
U.S.A.,) are strongly recommended.
Clearances
This heater must be installed with listed double-wall connector and compatible chimney system listed on page 7.
Clearances to combustible surfaces and materials are
shown below in Figure #1 and Figure #2, page 7.
Clearances may be reduced with various heat insulating
materials. Consult local fire codes and authorities for
approval.
NOTE: Longer chimney lengths and different pitch
flashings may be used. All other parts listed must be
installed (see Figure #2, Page 7). Install all components
to the connector or chimney manufacturer's installation
requirements. Consult your chimney supplier for installation advice.
CAUTION: THE STRUCTURAL INTEGRITY OF THE
MOBILE HOME FLOOR, WALL AND CEILING/ROOF
MUST BE MAINTAINED.
Note: See "Combustion Air" section onpage 9.
1. Position stove and floor protection with hole for combustion air in accordance with the clearances as stated
on the label and in Figure #1.
2. Mark the position for the hole in the ceiling and roof
by using a string and plumb-bob.
3. Check that the intended location will not interfere with
floor joists, ceiling joists or rafters before proceeding
further.
4. Cut a hole in the ceiling and roof to suit the chimney
system and frame in the sides. The chimney support
is mounted to the framing.
5. Assemble chimney sections so the finished length
is resting on the support and protruding through the
roof. Avoid having joints between ceiling and roof.
Install radiation shield. Assemble flashing and storm
collar and be sure to maintain the vapour barrier at
this point. (Seal securely.) Attach rain cap and check
flashing for leaks.
6. Install connector as per manufacturer's instructions.
7. Attach stove to flooring using two 1/4" x 2" or longer
lag screws.
Single Wall Connector - Residential
FIG. #1
11"
12"
22"
25"
18"
Minimum
Clearance to
Combustibles
30"
11"
Double Wall Connector - Residential
15"
5"
20"
14"
10"
4"
18"
16"
26"
16"
28"
4"
Alcove: Min. Height 7 1/2'
Max. Depth 4'
Double Wall Connector - Mobile Home
18"
8"
8"
22"
16"
28"
8"
6
SUPER-SD1
071111-20
Spark arrestor rain cap
FIG. #2
Chimney
3' (914 mm)
Minimum
The chimney may incorporate an offset. To do
this safely, all sections
of listed connector, offset elbows and chimney section must be
screwed together by at
least three sheet metal
screws per joint. The
chimney must be suitably supported by the
chimney manufacturer's
Storm collar
Roof flashing
Radiation shield
Minimum 7' (2.1m.)
Ceiling Height
Chimney Sup-
56" (1422 mm)
Minimum
Chimney ConAttachment to floor for
mobile homes
48"
(1219 mm)
Non-combustible
floor protector
Hooded vent or
90 elbow turned
* 4" diameter air inlet with rodent
screen
* If the crawl space is well ventilated
Listed Chimney and Chimney Connector
This appliance, when installed in a Mobile Home, must be installed with:
A. One of the following 6" double-wall connector systems:
1. Security Model DL or DC
5. Metal Fab Model DW
2. Oliver MacLeod Model PV
6. Ameri-Tec Model DBSP
3. Energy Vent
7. Industrial Chimney Model Excel Ultra-Black
4. Selkirk Metalbestos Model DS
8. Simpson Dura-Vent Model DVL
B. As well as one of the following compatible chimney systems - All parts 6":
CANADA ONLY:
Security
S2100
Pro-Jet
H.T.3000
ICC
Selkirk
Energy Vent
Excel 2100 Sentinal CF Commander 5000
Ceiling support
Rafter radiation shield
3' Chimney length
2' Chimney length
Roof flashing
Storm collar
Spark arrestor rain cap
XSF
SF
CF-CSP
CH6LCS
XL3
XL2
XFA
XSC
XCPE
FCS
RRS
SL3
SL2
RF17
SC
RCSA
L3
L2
FA
SC
CPE
CF-36SL
CF-24
CF-FRA
CF-SC
CF-SA,CT
CH636
CH624
CH6TCF
CH6SC
CH6RC, SS
USA ONLY:
Security
S2100
Pro-Jet
H.T.3000
Security
ASHT
Pro-Jet
HT3103
Metalbestos MetalFab
SSII
2100
Ameritech
TEC HS
ICC
Simpson Dura-Vent
Excel 103HT Dura/Plus Dura Tech
Ceiling support
Rafter radiation shield
3' Chimney length
2' Chimney length
Roof flashing
Storm collar
Spark arrestor rain cap
XSF
FCS
RRS
SL3
SL2
RF17
SC
RCSA
SF
FCS
RRS
SL3
SL2
RF
SC
RCSA
T-SFA
T-JSMH
T-36
T-24
T-SFA
T-SC
T-CT
6PL-CS
RDS/SQS
SDP-SB
SDP-SB
HS 36
HS 24
8RFFU
PL-ASCG
6PL-MPC
CL48
CL24
VF
SC
RCS
SDP-P
SDP-P
SDP-F
SDP-SC
SDP-C
SDT-P
SDT-P
SDT-F
SDT-SC
SDT-C
071111-20
XL3
XL2
XFA
XSC
XCPE
L3
L2
FA
SC
CPE
TGCSP
TGRS
TG3
TG2
TGF
TGSC
TGC
SUPER-SD1
7
Residential
Installation
Warning: Under no circumstances is this heater to be
installed in a makeshift or "temporary" manner. It may be
fired only after the following conditions have been met.
*
*
*
DO NOT ATTEMPT TO CONNECT THIS HEATER
TO ANY AIR DISTRIBUTION DUCT.
The services of competent installer are strongly recommended.
Outside combustion air or fresh air into the room may
be required in your area, consult local building codes
(see Combustion Air section).
- The services of a competent or certified installer, (certified
by the Wood Energy Technical Training program (WETT)
- in Canada, Hearth Education Foundation (HEARTH) - in
U.S.A.,) are strongly recommended.
Clearances
1. This heater may be installed using a single-wall connector (smoke pipe) or listed double-wall connector
(see Mobile Home installation).
2. Clearances to combustible surfaces and materials
using single-wall connector are shown in Figure #1,
page 6.
Clearances may be reduced with various heat insulating materials. Consult local fire codes and authorities
for approval.
3. Alternately, for close clearances, use a listed doublewall connector. See Diagram #1, page 6.
Single-Wall Connector
Smoke pipe must be:
* as short and straight as possible, use six inch diameter, 24 gauge black pipe that is clean and in new
condition.
* secured at every joint and collar with 3 sheet metal
screws.
* installed with the crimped or male ends pointing down.
This will carry any liquid creosote or condensation
back into the stove.
* The chimney connector shall not pass through an attic,
roof space, closet or similar concealed space, floor,
or ceiling. Where passage through a wall, or partition
of combustible material is desired, the installation
shall conform to CAN/CSA-B365, Installation Code
for Solid-Fuel-Burning Appliances and Equipment.
Procedure
1. If a listed chimney and double-wall connector is to
be connected to the stove, install all components to
the chimney manufacturer's installation requirements.
(Outside combustion air may be required, consult
local building codes. See Combustion Air section.)
2. If it is desirable to use smoke pipe in conjunction with
the insulated chimney, see step 4.
3. If a roof or ceiling support is used in the installation,
you will find the chimney manufacturer's complete
instructions packed with the roof support.
4. To start installing smoke pipe (chimney connector),
slip crimped edge of the pipe inside the stove collar.
Use holes provided in collar to secure pipe with two
screws.
5. Install the remaining lengths of pipe one on top of the
other to the finished height of the chimney connector
and secure to each other.
Chimney and Connector
Connect to a listed chimney or a chimney suitable for use
with solid fuel that is lined and in good condition and
meets local building codes. The chimney flue size should
be the same as the stove outlet for optimal performance.
Reducing or increasing the flue size may adversely affect
stove performance. Chimney flue exit is to be 3 feet (1 m.)
above roof and two feet (0.6 m.) above highest projection
within 10 feet (3 m.). The installation must meet all local
codes. Do not connect this unit to a chimney flue serving
another appliance. Minimum system height is 15 feet (4.6
m.) (measured from base of appliance).
Double-Wall Connector
-
8
Use a listed double-wall connector.
Install all components to the chimney connector
manufacturer's installation requirements.
SUPER-SD1
071111-20
Floor Protector Combustion Air
The stove may be installed on a combustible floor provided
noncombustible ember protection is used.
This protection must extend as follows:
In Canada: 18" (457 mm) on the firing side and 8" (203
mm) to the other sides. See Figure #3, below.
In USA: 16" (406 mm) to the front and 8" (203 mm) to the
Canada Only
FIG. #3
Minimum Width - 40'
Minimum Overall Depth - 50 1/2"
Non-combustible
8" [203mm]
8" [203mm]
8" [203mm]
18" [457mm]
sides of the fuel loading door opening. See Figure #4,
below. This protection is also required under the chimney
connector and 2" (51 mm) beyond each side.
FIG. #4
Minimum Width - 34"
Minimum Overall Depth - 40 1/2"
Non-combustible
floor protector
8" [203mm]
8" [203mm]
071111-20
1. Outside air supply - (Necessary for mobile home installation, optional for residential installation.) To draw
outside air through the floor, leave the 4" knockout in
the rear of the pedestal or leg kit ash box enclosure
in place.
Pedestal Model: Cut or drill a 4" diameter or larger
hole in the floor anywhere inside the perimeter of the
pedestal. Cover the hole with a 4" x 4" (100 mm x
100 mm) rodent screen and staple/nail in place.
Leg Model: Cut or drill a 4" diameter hole directly
below the bottom knockout hole of the ash box enclosure. Connect enclosure to the floor with a short
4" diameter pipe.
This hole must get its air from a ventilated crawl
space or be extended with duct to the outdoors (see
Figure #2, Page 7). The use of outside combustion
air for residential installation requires the unit to be
secured to the structure to prevent dislodging of the
air duct. Outside air may also be ducted from outside
through the 4" diameter knockout hole in the rear of the
pedestal or leg kit ash box enclosure. If this method
of supplying combustion air is used in conjunction
with the optional blower kit, an outside air adaptor
may be required (see Optional Blower section).
Note: This unit is not designed to be operated with the
firing door open. In addition to the obvious hazard of
sparks landing on combustibles, an open fire door
will cause the heater to draw air from the living space
and possibly cause suffocation.
U.S.A. Only
16" [406mm]
Intake or combustion air can be supplied to the stove
in one of
two ways. Consult your local building code or CAN/CSAB365, Installation Code for Solid-Fuel-Burning Appliances
and Equipment before proceeding.
2. Room air supply - Remove the 4" plug from the rear
of the pedestal or leg kit ash box enclosure. The
stove will now draw its air from the room through this
opening and into the firebox intake.
Note: The living space around the heater must be well
ventilated with good air circulation. Anything that may
cause a negative pressure can cause gases or fumes
to be pulled into the living area. During extremely cold
weather, and especially when burning at very slow
rates, the upper parts of the exposed chimney may
ice up, partially blocking the flue gases. If blockage
occurs, flue gases may enter living space.
SUPER-SD1
9
Operation
Open all windows and doors. Smoke and fumes caused
by the curing process may cause discomfort to some
individuals.
CAUTION: Never use gasoline, gasoline type lantern
fuel, kerosene, charcoal lighter fluid or similar liquids to
start or "freshen up" a fire in this heater. Keep all such
liquids well away from the heater while it is in use.
Lighting a Fire
CAUTION: Hot while in operation. Keep children,
clothing and furniture away. Contact may cause
skin burns.
Your PACIFIC ENERGY heater is designed formany
years of trouble free operation. Over firing the appliance
will shorten the life of the product. Failure to recitify an
over firing condition can be hazardous and may void the
manufacturer's warranty.
1. Adjust air control to position H (maximum firing rate)
and open door.
2. Place crumpled newspaper in the centre of the heater
and criss-cross with several pieces of dry kindling.
Add a few small pieces of dry wood on top.
3. Ignite the paper and close the door.
4. After the fire has established itself, open the door and
add a few small logs. Close door.
5. Begin normal operation after a good coal base exists
and wood has charred.
Wood Selection
Normal Operation
This heater is designed to burn natural wood only. Higher
efficiency and lower emissions generally result when
burning air-dried seasoned hardwoods, as compared to
softwoods or to green or freshly cut hardwoods.
Wood should be properly air dried (seasoned) for six
months or more. Wet or undried wood will cause the fire
to smoulder and produce large amounts of creosote.
Wet wood also produces very little heat and tends to go
out often.
1. Set air control to a desired setting. If smoke pours
down across the glass (waterfall effect) this indicates
you have shut the control down too soon or you are
using too low a setting. The wide range control panel
makes finding the desired setting for your application
easy. As every home's heating needs vary (ie. insulation, windows, climate, etc.) the proper setting can
only be found by trial and error and should be noted
for future burns.
2. To refuel, adjust air control to high, and give the fire
time to brighten. Open the door slowly, this will prevent
backpuffing.
3. Use wood of different shape, diameter and length (up
to 18"). Load your wood endwise and try to place the
logs so that the air can flow between them. Always
use dry wood.
4. Do not load fuel to a height or in such a manner that
would be hazardous when opening the door.
5. For extended or overnight burns, unsplit logs are
preferred. Remember to char the wood completely
on maximum setting before adjusting air control for
overnight burn.
Over Firing
DO NOT BURN :
-Salt water wood *
-Treated wood
-Wet or green wood
- C o a l / c h a rcoal
-Garbage/Plastic *
-Solvents
* These materials contain chlorides which will rapidly
destroy metal surfaces and void warranty.
Do not burn anything but wood. Other fuels, eg. charcoal,
can produce large amounts of carbon monoxide, a tasteless, odourless gas that can kill. Under no circumstances
should you attempt to barbecue in this heater.
How to Test Your Wood
Add a large piece of wood to the stove when it has a good
large bed of coals. It is dry if it is burning on more than
one side within one minute. It is damp if it turns black
and lights within three minutes. If it sizzles, hisses and
blackens without igniting in five minutes it is soaked and
should not be burnt.
WARNING: Never use chemicals or any other volatile
liquid to start a fire.
WARNING: Always keep loading door closed when
burning. This heater is not designed for open door
burning.
WARNING: No alteration or modification of the
combustion air control assembly is permitted. Any
tampering will void warranty and could be very hazardous.
Lighting for the First Time
Curing of the Paint Finish
To achieve the best finish, the paint on your stove must
be baked on. When burning your stove for the first 2-3
times it is very important that the room be well ventilated.
10
SUPER-SD1
WARNING: Do not use grates or andirons to elevate
the fuel. Burn directly on the fire bricks. Replace
broken or missing bricks. Failure to do so may create a hazardous condition.
071111-20
Restarting After Extended or
Overnight Burns
1. Open door and rake hot embers towards the front of
the heater. Add a couple of dry, split logs on top of
embers, close door.
2. Adjust air control to high and in just a few minutes,
logs should begin burning.
3. After wood has charred, reset air control to desired
setting.
4. To achieve maximum firing rate, set control to high
"H". Do not use this setting other than for starting or
preheating fresh fuel loads.
DO NOT OVERFIRE THIS HEATER: Attempts to
achieve heat output rates that exceed heater design
specifications can result in permanent damage to
the heater and chimney.
More Wood, More Heat
Seasoned wood has approximately 7500 BTU's per pound.
If you put 10 pounds of wood in your stove for an eight
hour burn the wood will be producing 9375 BTU's per hour.
(7500 BTU x 10 lbs./8hrs.=9375 BTU's per hr.) If you put
20 lbs of wood in your stove for eight hour burn you will
get 18,750 BTU's per hr. (7500 BTU x 20lbs./8hr.=18,750
BTU's per hr.). This is only an example and is based on
100% efficiency. In reality, your stove should perform
above the 80% range.
Experience will give you the right settings for proper
combustion and efficient burning. Remember the correct
air inlet setting is affected by variables such as type of
wood, outside temperature, chimney size and weather
conditions. With practice, you will become proficient in
operating your heater and will obtain the performance
for which it was designed.
Proper Draft
1. Draft is the force which moves air from the appliance
up through the chimney. The amount of draft in your
chimney depends on the length of the chimney, local
geography, nearby obstructions and other factors.
2. Too much draft may cause excessive temperatures
in the appliance. An uncontrollable burn or a glowing
red stove part or chimney indicates excessive draft.
3. Inadequate draft may cause backpuffing into the room
and plugging of the chimney. Smoke leaking into the
room through appliance and chimney connector joints
indicates inadequate draft.
071111-20
Ash Removal
Caution: Ashes are to be removed only when the heater
is cold.
Whenever ashes get 3 to 4 inches deep in your firebox,
and when fire has burned down and cooled, remove
excess ashes. Leave an ash bed approximately 1" (25
mm) deep on the firebox bottom to help maintain a hot
charcoal bed.
Optional Ash Cleanout system: The ash dump handle
is located under the ash lip on the left hand side. To operate ash dump, pull handle out 1/2" and turn clockwise.
This will unlock the ash dump and allow it to open. Hold
handle open while pulling ashes into the opening. Avoid
large embers as these still contain heat value. Release
handle and push in to lock. Ensure ash dump door is
properly engaged. Fill the cavity with the remaining ash
level with the firebox floor. Lift and pull out ashpan and
discard ashes into metal container. Replace ashpan and
ensure it is seated properly.
Do not burn with ash dump door open. Doing so will
create a hazardous condition. Always leave about 1"
of ash when cleaning.
Disposal of Ashes
Ashes should be placed in a metal container with a tight
fitting lid. The closed container of ashes should be placed
on a non-combustible floor or on the ground, well away
from all combustible materials, pending final disposal. If
the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in closed
container until all cinders have thoroughly cooled. Other
waste should not be placed in this container.
Baffle Removal
Chimney connector pipe should be disconnected from
stove to clean and inspect. Only if this is not possible
should you remove baffle assembly.
DO NOT OPERATE WITH BAFFLE ASSEMBLY OR
INSULATION REMOVED.
Removal
Remove retaining pin at the back top of the firebox, just
under the baffle. Lift baffle up and pull forward to disconnect from the supply tube. Tilt baffle sideways to drop
down and remove from firebox. Inspect gasket between
baffle and supply tube. If necessary, replace with gasket
#139.5 available from your Pacific Energy dealer. Re-install
baffle assembly in reverse order. The two side pieces of
insulation must be tight against the siderails.
SUPER-SD1
11
Optional
Blower
The optional blower kit (kit #WODC.BLOW) is equipped
with a three prong power cord and may be installed at
any time. Follow installation instructions supplied with the
kit. Route power supply cord away from heater.
Electrical rating: 115 volts A.C.-1.02 amps.
Fan output rating: 125 CFM
Optional Outside Air Adaptor
The adaptor is only required if the blower kit is to be installed and outside combustion air to be ducted to rear
of pedestal.
Installation:
Remove blower kit if already installed. Place adaptor with
the 4" round hole facing up and opposite end covering
the room air knockout hole on the back of the pedestal.
Mark attachment holes on pedestal base and drill with
1/8" bit. Attach with #8 x 1/2" screws and reinstall fan.
Combustion air duct from outside can now be attached
to the 4" round collar.
Blower Operation
Proper blower speed matched with air control setting
will ensure peak performance from your stove. Operate
as follows:
- Air control set to "L" (low), operate blower speed
control on "Low".
- Air control set between "L" and "H" (low and high),
operate blower speed control at desired setting.
Automatic: To operate the blower automatically, set the
rocker switch on the side of the fan housing to "Auto"
and set the speed control to desired setting. This will allow the fan to turn on as the stove heats up to operating
temperature. It will also shut the blower off after the fire
has gone out and the unit cooled to below a useful heat
output range.
Manual: To manually operate the blower, set the rocker
switch to "Man" and set the speed control to desired setting. This will bypass the sensing device and allow full
control of the blower.
Switching from "Auto" to "Man" or selecting speed may
be done anytime.
12
SUPER-SD1
071111-20
Appendix A
Troubleshooting
Problem
Cause
Cure
Glass is Dirty
1. Wood is wet
- Use dry wood
2. Turning down air control
or damper too soon
- Do not turn down until
a) there is a good bed of coals
b) the wood is charred
3. Draft too low
- Improper chimney height and / or diameter
- Chimney plugged or restricted, check flue
- Provide outside air for combustion
4. Door gasket leakage
- Replace gasket
- Check latch
Excessive Creosote Buildup - See 1,2,3, above.
Low Heat Output
1. Wood is wet
2. Fire too small
3. Draft too low
- Use dry wood
- Build a larger fire
- Chimney plugged or restricted, inspect and
Won't Burn Overnight
1. Air control is set too high
2. Not enough wood
3. Draft too high
- Set control lower
- Unsplit wood is preferred for overnight burns
- Excessive chimney height and/or diameter,
see page 11
Stove Won't Burn
1. Combustion air supply blocked - Check outside air supply for obstruction
- Check that room air cover is removed
clean
2. Draft too low
- Chimney plugged or restricted, inspect and
clean
071111-20
SUPER-SD1
13
Replacement Parts - Super 27
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)
ITEM
DESCRIPTION
PART NO.
ITEM DESCRIPTION
All parts may be ordered from your nearest Pacific Energy
dealer. Contact Pacific Energy for the location of the dealer
17
14
14
16
PART NO.
20.......... Ash System (Leg Model) ................ SUPD.LGADA
21.......... Leg, Black.........................................CAST.LEGST
.............. Leg, Gold Plated............................CAST.LEGGLD
.............. Leg, Nickel Plated ............................ CAST.LEGNI
24.......... Ash Dump Assembly .........................WODC.2261
25.......... Ash Box (Pedestal Model) ................ WODC.4316
26.......... Air Shutter Assembly .........................WODC.4531
27.......... Baffle Air Control Assembly .................. SSER.214
1............ Side Shield, Left or Right.................... SUPD.4302
2............ Rear Deflector ...................................... SSER.229
3............ Door Catch ........................................ WODC.1461
4............ Ash Lip (c/w Trim & Hardware) ..ALIP.5037473MB
5............ Glass Clamps (4 pc.)......................... SSER.1425
6............ Glass Bar Set (2 pc.) ...................... WODC.41405
7............ Replacement Glass (c/w Tape) .....DR31.WGLKIT
8............ Door Gasket Kit ............................. DR31.WDGKIT
9............ Door Casting, Arched Black ................CAST.31ST
.............. Door Casting, Radiant Black ..........CAST.31RSST
.............. Door Casting, Arched Gold.................CAST.31GD
.............. Door Casting, Radiant Gold ..........CAST.31RSGD
.............. Door Casting, Arched Nickel.................CAST.31NI
.............. Door Casting, Radiant Nickel ..........CAST.31RSNI
10 .......... Door Handle Assembly ................... WODC.4147C
11 .......... Boost Manifold .............................................. 4105
12 .......... Firebrick Set .................................... BRIC.SSERA
13a ........ Brick Rail, Left/Right .................... SSER.RAILSET
14 .......... Replacement Baffle Kit .................. SSER.DBAKIT
15 .......... Baffle Pin .........................................SSER.125001
16 .......... Baffle Gasket ...................................... SSER.1395
17 .......... Flame Shield (c/w Bolt and Nut).........SSER.4115
18 .......... Pedestal Front Cover .......................... SSER.2075
19 .......... Pedestal Assembly .............................. SUPD.PED
1
2
28
1
15
3
14
4
13a
26
6
9
27
5
13b
8
28
7
19
10
9
18
20
25
24
10
11
20
21
12
20
14
SUPER-SD1
071111-20
Replacement Parts - Spectrum and Spectrum Classic
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)
ITEM
DESCRIPTION
PART NO.
ITEM DESCRIPTION
PART NO.
20.......... Ash Box (Spectrum) ......................... WODC.4316
21.......... Pedestal Assembly .............................. SUPD.PED
22.......... Pedestal Cladding (Hinge Side) .......... SPEC.402
23.......... Pedestal Cladding (Latch Side) ........... SPEC.403
24.......... Ash Drawer Enclosure (Classic)..SUPD.ASHLEG
25.......... Leg, Gold Plated............................CAST.LEGGLD
.............. Leg, Nickel Plated ............................CAST.LEGST
.............. Leg, Black......................................... CAST.LEGNI
27.......... Ash Dump Assembly .........................WODC.2261
28.......... Ash Box Cladding (Por. Finish) ......SPED.4406_ _
29.......... Air Shutter Assembly .........................WODC.4531
30.......... Baffle Air Control .................................. SSER.214
All parts may be ordered from your nearest Pacific Energy
dealer. Contact Pacific Energy for the location of the dealer
nearest you.
When ordering porcelain finish parts, please specify the
appropriate code as follows:
Black ......BK
Black Pearl.........BP
Ivory .......IY
Coffee Brown.....CB
Blue........BE
Copper...............CU
Red ........RD
Titanium.............GN
Green .....GN
1............ Side Shield, Left or Right............. SPED.4403_ _B
2............ Rear Deflector .....................................SPEC.4418
3............ Top Panel (Porcelain Finish) ......... SPED.401_ _A
4............ Screen Trivet, Classic Gold ............ CLAD.CTGDA
.............. Screen Trivet, Classic Nickel ............ CLAD.CTNIA
.............. Screen Trivet, Black .........................CLAD.CTBKA
5............ Door Catch ........................................ WODC.1461
6............ Ash Lip ........................................ SPED.4401_ _B
7............ Glass Clamps (4 pc.)......................... SSER.1425
8............ Glass Bar Set (2 pc.) ...................... WODC.41405
9............ Replacement Glass (c/w Tape) .....DR31.WGLKIT
10 .......... Door Gasket Kit ............................. DR31.WDGKIT
11 .......... Door Casting, Arched Black ................CAST.31ST
.............. Door Casting, Radiant Black ..........CAST.31RSST
.............. Door Casting, Arched Gold.................CAST.31GD
.............. Door Casting, Radiant Gold ..........CAST.31RSGD
.............. Door Casting, Arched Nickel.................CAST.31NI
.............. Door Casting, Radiant Nickel ..........CAST.31RSNI
12 .......... Door Handle Assembly ................... WODC.4147C
13 .......... Boost Manifold .............................................. 4105
14 .......... Firebrick Set .................................... BRIC.SSERA
15a ........ Brick Rail, Left/Right .................... SSER.RAILSET
16 .......... Replacement Baffle Kit .................. SSER.DBAKIT
17 .......... Baffle Pin .........................................SSER.125001
18 .......... Baffle Gasket ...................................... SSER.1395
19 .......... Flame Shield (c/w Bolt and Nut).........SSER.4115
4
3
1
2
31
19
16
16
23
5
18
17
1
6
16
31
7
15a
15b
9
11
30
8
21
29
10
22
12
11
28
20
24
27
12
13
25
14
24
071111-20
LEG KIT FOR SPECTRUM
CLASSIC ONLY
SUPER-SD1
15
Understanding & Operating Your Pacific Energy Stove
The Pacific Energy SUPER SERIES line of
woodstoves is a culmination of years of research
and development. Designed to be efficient,
clean-burning and user-friendly, this heater will
give you years of warm service. However, a
knowledgeable operator is still the most important factor for maximum performance and part
of this is understanding the basic functions of
this design.
Traditional wood stoves had a basic combustion
system which allowed a considerable amount of
heat energy to escape up the chimney as unburned gases and particulates (smoke). Pacific
Energy has designed a system that solves the
problem by burning the smoke and releasing
the additional heat to the room.
This system has two critical design features:
1. Above fire secondary air injection:
The hollow "air baffle" injects super-heated secondary air just above the load. With the stove
at the proper operating temperature, this will
create a secondary flame that will be evident for
approximately 1/3 of the total burn time.
OPERATING TIPS
1. Always use dry, seasoned firewood, up to 18"
long. Load wood endwise, a mixture of large
and small pieces, on top of a good ash base
(1" minimum).
2. Operate on a medium to high setting, for up
to 1 hour from cold start. After the initial warm
up period, refuel and leave the air control on a
medium setting for 5 to 10 minutes more and
then set the air control to the desired position.
3. If a slow burn is desired, set the air control to
low. Active secondary burning should be present
above the wood load. If it is not present or goes
out shortly after, proper operating temperature
has not been reached and the stove needs additional warm up time.
6
5
2. High mass and thermal insulation:
The high mass (weight) acts as a heat storage
and the thermal insulation keeps the combustion
zone hot. Active flaming takes place during the
first part of the burn. During this stage, heat is
stored in the mass of the unit and is later released
slowly and evenly. As wood chars, active flaming
will diminish. This clean charcoal burning stage
will last for a considerable length of time and
refuelling should be avoided until the charcoal
base has become quite small.
3
2
1
1 -Boost Air
2 -Main Combustion Air
3 -Air Wash System
16
SUPER-SD1
4
4 -Secondary Combustion Zone
5 -Radiant Heat
6 -Convected Heat
071111-20
Super 27 and Pacific
Pedestal or Legs
Installation Instructions
Required:
Pedestal Kit
Leg Adapter
1
1
1
1
4
Pedestal base
Front cover (attached)
Ash drawer enclosure
Front cover (attached)
1/2" washers
with
Leg Set
4
Legs
NOTE: Optional ash dump kit should be installed prior to pedestal or leg kit
assembly.
Crate Removal
1)
2)
3)
4)
5)
6)
Carefully remove wood top and supports.
Remove plastic cover.
Using a 7/16" wrench, remove lag bolts that secure stove body to bottom
pallet.
Place stove body carefully on its back.
Using a 3/4" wrench, remove 1" x 1/2" bolts and save for later use.
Remove pallet retaining brackets from stove bottom.
Pedestal Kit
1)
2)
3)
With the unit on its back and the removable cover facing up, align the pedestal
mounting holes with the holes on the stove.
Secure in place with 1" x 1/2" bolts previously removed.
Carefully place the unit in the upright position.
Leg Adapter and Leg Kit
1) With the unit on its back, align the ash drawer enclosure mounting holes
(removable cover facing up) with the holes on the stove.
2) Position the legs over top of the same holes on the stove.
3) Secure in place with 1" x 1/2" bolts previously removed.
071111-20
SUPER-SD1
17
NOTES
18
SUPER-SD1
071111-20
Label
CERTIFIED FOR CANADA AND U.S.A.
LISTED ROOM HEATER, SOLID FUEL TYPE.
ALSO FOR USE IN MOBILE HOMES
TESTED TO CAN/ULC S627-M93 AND UL 1482-98
ALDERLEA T5
SPECTRUM CLASSIC
SUPER 27
MODEL SERIES D:
WN# 16408
DO NOT REMOVE THIS LABEL
WH-
• INSTALL AND USE IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS.
• CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS, INSTALLATION PERMIT AND INSPECTION IN
YOUR AREA.
• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE (USA. ONLY).
• USE 6 INCH / 150MM DIAMETER MINIMUM 24 MSG BLACK OR LISTED CONNECTOR.
• CONNECT TO A LINED MASONRY CHIMNEY SUITABLE FOR USE WITH SOLID FUELS.
• DO NOT OBSTRUCT THE SPACE BENEATH THE HEATER.
• SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED WHEN PASSING
A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING.
• DO NOT PASS A CHIMNEY CONNECTOR THROUGH A COMBUSTIBLE WALL OR CEILING.
• MINIMUM CLEARANCE BETWEEN SINGLE WALL CHIMNEY CONNECTOR AND COMBUSTIBLE MATERIALS18INCHES/455MM. CLEARANCE MAY BE REDUCED BY THE USE OF LISTED PIPE SHIELDS, WALL PROTECTORS OR
OTHER MEANS APPROVED BY LOCAL BUILDING OR FIRE OFFICIALS.
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS
RESIDENTIAL INSTALLATION
USING SINGLE WALL CONNECTOR
VERTICAL CONNECTOR
A.
B.
C.
D.
E.
F.
SIDEWALL TO UNIT
BACKWALL TO UNIT
CORNER TO UNIT
SIDEWALL TO CONNECTOR
BACKWALL TO CONNECTOR
CORNER TO CONNECTOR
18 in. / 455 mm
12 in. / 305 mm
11 in. / 280 mm
27 in. / 685 mm
19 in. / 485 mm
22 in. / 560 mm
RESIDENTIAL CLOSE CLEARANCE
INSTALLATION
USING DOUBLE WALL CONNECTOR
HORIZONTAL CONNECTOR VERTICAL CONNECTOR HORIZONTAL CONNECTOR
14 in. / 355 mm
8 in. / 200 mm
11 in. / 280 mm
23 in. / 585 mm
15 in. / 380 mm
22 in. / 560 mm
14 in. / 355 mm 14 in. / 405 mm
5 in. / 127 mm
5 in. / 127 mm
4 in. / 102 mm
4 in. / 102 mm
22.5 in. / 570 mm 22.5 in. / 570 mm
11.5 in. / 292 mm 11.5 in. / 292 mm
14.5 in. / 370 mm 14.5 in. / 370 mm
* ALCOVE
INSTALLATION
USING
DOUBLE WALL
CONNECTOR
MOBILE HOME
INSTALLATION
USING
DOUBLE WALL
CONNECTOR
16 in. / 405 mm 16 in. / 405 mm
10 in. / 255 mm
8 in. / 200 mm
N/A
8 in. / 200 mm
24.5 in. / 620 mm 24.5 in. / 620 mm
16.5 in. / 420 mm 14.5 in. / 370 mm
N/A 18.5 in. / 470 mm
G.
H.
I.
16 INCHES / 405 MM
5 INCHES / 127 MM
0 INCHES / 0 MM
18 INCHES / 455 MM
8 INCHES / 200 MM
8 INCHES / 200 MM
IN U.S.A.
G.
H.
I.
IN CANADA
HORIZONTAL CONNECTOR NOT PERMITTED IN MOBILE HOMES
AS TESTED - PIPE SHIELD MAY BE REQUIRED BY LOCAL AUTHORITIES.
* COMBUSTIBLE ALCOVE SIZE : DEPTH - 4 FT. / 1.22 M MAXIMUM, HEIGHT 7 1/2 FT. / 2.3 M MINIMUM
COMBUSTIBLE FLOOR MUST BE PROTECTED BY A CONTINUOUS NON-COMBUSTIBLE MATERIAL EXTENDED TO THE
FRONT, SIDES AND BACK AS INDICATED.
•
COMPONENTS REQUIRED FOR MOBILE HOME AND ALCOVE INSTALLATION: OUTSIDE AIR KIT, AND ONE OF THE
FOLLOWING LISTED CONNECTORS: SECURITY MODELS DP OR DC, OLIVER MACLEOD MODEL PV, ENERGY VENT
E VENT, SELKIRK METALBESTOS MODEL DS, METAL FAB MODEL DW, AMERI-TEC MODEL DBSP, INDUSTRIAL
CHIMNEY MODEL EXCEL ULTRA-BLACK, OR SIMPSON DURA-VENT MODEL DVL IN COMBINATION WITH ONE OF THE
FOLLOWING COMPATIBLE CHIMNEY SYSTEMS: APPLIANCE MUST BE INSTALLED WITH PEDESTAL OR LEG KIT
ATTACHED.
IN CANADA - SECURITY MODEL S2100, OLIVER MACLEOD PROJET MODEL HT 3000, SELKIRK SENTINEL MODEL CF,
INDUSTRIAL CHIMNEY MODEL EXCEL 2100.
IN USA - SECURITY MODEL ASHT OR S2100, OLIVER MACLEOD MODEL 3103 OR HT 3000, SELKIRK METALBESTOS
MODEL SS II, METAL FAB MODEL 2100, AMERI-TEC MODEL HS, INDUSTRIAL CHIMNEY MODEL EXCEL 103HT,
SIMPSON DURA-VENT MODEL DURA/PLUS AND DURA TECH.
USE COMPONENTS SPECIFIED IN PACIFIC ENERGY INSTALLATION INSTRUCTIONS.
• OPTIONAL COMPONENTS - WATER COIL (CANADA ONLY), FAN KIT #SSER.BLOW, FAN ELECTRICAL RATING: 115V,
60HZ, 80WATTS. DO NOT ROUTE POWER CORD BENEATH HEATER.
• CAUTION: RISK OF EXCESSIVE TEMPERATURES - KEEP ASH DUMP CLOSED DURING FIRING OF THE HEATER.
• OPERATE ONLY WITH FEED DOOR CLOSED. OPEN TO FEED FIRE ONLY.
• KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIALS WELL AWAY FROM HEATER.
• REPLACE GLASS ONLY WITH CERAMIC GLASS.
CAUTION
MANUFACTURED BY:
PACIFIC ENERGY FIREPLACE PRODUCTS LTD.
2975 ALLENBY RD., DUNCAN, BC V9L 6V8
HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN,
CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN
BURNS. SEE NAMEPLATE AND INSTRUCTIONS.
U.S. ENVIRONMENTAL PROTECTION AGENCY
CERTIFIED TO COMPLY WITH
JULY, 1990, PARTICULATE EMISSION
STANDARDS
250509
071111-20
5050.75
DATE OF MANUFACTURE
J F
2009
M A
2010
MADE IN CANADA
M J J A S O N D
2011 2012 2013 2014
SUP1-A2
SUPER-SD1
19
PACIFIC ENERGY FIREPLACE PRODUCTS LTD.
2975 Allenby Rd., Duncan, B.C. V9L 6V8
Phone: 250-748-1184
Web site: http://www.pacificenergy.net
Printed in Canada
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising