Installation and Operation Instructions
Astria® Outdoor Wood Burning Fireplace
PFS
P126758-01
P/N 126758-01 Rev. B 10/2015
C
Models
®
US
Oracle36
Oracle42
Oracle50
REPORT NO. F09-095
SAVE THIS BOOK
This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also
contains information that will enable you to obtain replacement parts or accessory items when needed. Keep
it with your other important papers.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
This wood burning fireplace complies with UL127
CAN/ULC-S610-M87 standard as a FACTORY
BUILT FIREPLACE.
Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour consultation ultérieure.
Ce foyer au bois est conforme aux UL 127 CAN/ULCS610-M87 norme comme une USINE CONSTRUITE
CHEMINÉE.
This fireplace is approved for use as a wood burning fireplace or for use with a vented gas log approved to
ANSI Z21.60 or Z21.84 standards or for use with a vent-free gas log heater approved to ANSI Z21.11.2 standard.
FOR CANADA: The authority having jurisdiction
(such as the municipal building department, fire
department, etc.) should be contacted before
installation to determine the need to obtain a permit.
POUR LE CANADA: L’autorité compétente (comme le
service municipal du bâtiment, les pompiers, etc.) doit
être contacté avant l’installation afin de déterminer la
nécessité d’obtenir un permis.
This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace
system. Please read and understand these instructions before beginning your installation.
Do not alter or modify the fireplace or its components under any circumstances. Any modification or alteration of
the fireplace system, including but not limited to the fireplace, chimney components and accessories, may void the
warranty, listings and approvals of this system and could result in an unsafe and potentially dangerous installation.
IMPORTANT! TO ASSURE PROPER ALIGNMENT OF GLASS DOORS: INSTALL THIS FIREPLACE IN A SQUARE
AND PLUMB CONDITION, USING SHIMS AS NECESSARY AT SIDES AND/OR BOTTOM.
TABLE OF CONTENTS
Thank you for your purchase. We appreciate your
business!
Please carefully read and follow all instructions in this manual. Pay
special attention to all warnings and safety information.
Following these safety, care, and operation instructions will help
ensure many years of dependable and enjoyable service from your
fireplace.
Register your product online today!
To help us keep you up-to-date on product information and offers, please take a few moments to register your product online
at Astria.US.com
Please read and understand these instructions before installing
or operating.
Safety..............................................................................................2
Specifications..................................................................................4
Fireplace Installation.......................................................................7
Venting Installation.........................................................................9
Mosaic Masonry Brick and Estate Panels Installation ..................14
Optional Gas Line Installation.......................................................16
Glass Door Installation..................................................................17
Operation and Maintenance Guidelines.........................................18
Technical Service..........................................................................19
Replacement Parts........................................................................19
Parts.............................................................................................20
Accessories...................................................................................24
Warranty.......................................................................................27
SAFETY
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury
or property damage. Refer to this manual for correct
installation and operational procedures. For assistance or additional information consult a qualified
installer, service agency or the gas supplier.
IMPORTANT: Check local codes before installing this
fireplace.
Before beginning the installation of the fireplace, read these instructions through completely.
• This INNOVATIVE HEARTH PRODUCTS, LLC (IHP) fireplace and
its components are safe when installed according to this installation manual. Unless you use IHP components, which have been
designed and tested for the fireplace system, you may cause a
fire hazard.
• The IHP warranty will be voided by and IHP disclaims any responsibility for the following actions.
a.Modification of the fireplace, components, doors, air inlet
system and damper control.
b.Use of any component part not manufactured or approved by
IHP in combination with an IHP fireplace system.
Proper installation is the most important step in ensuring safe and
continuous operation of the fireplace. Consult the local building codes
as to the particular requirements concerned with the installation of
all factory built fireplaces.
2
WARNING: Do not install a fireplace insert in this
box unless the manufacturer's instructions with the
insert specifically state this fireplace has been tested
for use with this insert.
FOR YOUR SAFETY
•Do not store or use gasoline or any other flammable
vapors or liquids in the vicinity of this or any other
appliance.
•Due to high temperatures, the appliance should be
located out of traffic and away from furniture and
draperies.
•Do not place clothing or other flammable materials
on or near the appliance.
•Never leave children unattended when a fire is
burning in the fireplace.
WARNING: Use solid wood or processed solid fuel
firelogs only. When processed wood fuel fire logs are
used, do not poke or stir the logs while they are burning.
Use only fire logs that have been evaluated for the application in fireplace and refer to fire log warnings and
caution markings on packaging prior to use.
This fireplace is not intended to be used as a substitute
for a furnace to heat an entire home. Use for supplemental heat only.
Astria.US.com
126758-01B
SAFETY Continued
Overfiring of a fireplace is a condition where excessive
temperatures are reached, beyond the design capabilities
of the appliance. The damage that occurs from overfiring
is not covered under the manufacturer’s limited warranty.
WARNING: CONTINUED OVERFIRING CAN PERMANENTLY DAMAGE YOUR FIREPLACE SYSTEM.
SOME EXAMPLES OF CONDITIONS THAT COULD
CAUSE OVERFIRING ARE:
• BURNING QUANTITIES OF SCRAP LUMBER, PINE
BRANCHES, PAPER OR CARDBOARD BOXES
WHICH EXCEED THE VOLUME OF THE NORMAL
LOG FIRE.
• BURNING TRASH, CHEMICALS OR CHEMICALLY
TREATED COMBUSTIBLES.
Disposal of Ashes
Ashes should be placed in a metal container with a tightfitting lid. The closed container of ashes should be placed
on a noncombustible floor or on the ground, well away
from all combustible materials, pending final disposal.
If the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the closed
container until all cinders have thoroughly cooled.
WHEN USING THE DECORATIVE APPLIANCE, THE
FIREPLACE DAMPER MUST BE SET IN THE FULLY
OPEN POSITION.
Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start
or ’freshen up’ a fire in this fireplace. Keep all such
liquids well away from the fireplace while it is in use.
Use SOLID WOOD only for fuel. It is best to use dry
and well seasoned hardwood. Softwoods tend to burn
very quickly. DO NOT use treated wood, charcoal, coal,
trash, driftwood or woods that have been dipped in
tar, pitch, pine tar, creosote, etc. Wood products made
with synthetic binders, such as plywood, produce abnormally high temperatures and sputtering, smoking
fires. When burning artificial logs, please read and
follow the instructions provided by the manufacturer.
Never burn treated construction lumber or scraps.
These woods burn excessively hot and may contain
chemicals used to treat insects and fungus. When
burned, these chemicals can pose a significant hazard.
126758-01B
WARNING: BURNING IMPROPER FUEL (I.E. CHARCOAL) CAN RESULT IN CARBON MONOXIDE POISONING, WHICH MAY LEAD TO DEATH!
Carbon Monoxide Poisoning – Early signs of carbon
monoxide poisoning resemble the flu with headaches,
dizziness, or nausea. If you have these signs, get
fresh air at once! Have the appliance inspected by a
qualified service technician. Some people are more affected by carbon monoxide than others. These include
pregnant women, people with heart or lung disease
or anemia, those under the influence of alcohol, and
those at high altitudes.
Ventilation Requirements - Provide adequate air for
combustion. The fresh air requirements of this appliance must be met within the space where it will
be installed.
Smoke Detectors - Since there are always several
potential sources of fire in any home, we recommend
installing smoke detectors. If possible, install the
smoke detector in a hallway adjacent to the room (to
reduce the possibility of occasional false activation
from the heat produced by the appliance). If your local
code requires a smoke detector be installed within the
same room, you must follow the requirements of your
local code. Check with your local building department
for requirements in your area.
Creosote – Formation and Need for Removal
When wood is burned slowly, it produces tar and other
organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense
in the relatively cool chimney flue of a slow-burning
fire. As a result, creosote residue accumulates on
the flue lining. When ignited this creosote makes an
extremely hot fire.
The chimney shall be inspected at least twice a year
during the heating season to determine when a creosote
buildup has occurred. When creosote has accumulated
(1/8" [3 mm] or more) it shall be removed to reduce
the risk of a chimney fire.
WARNING: Children and adults should be alerted
to the hazards of high surface temperatures and to
stay away to avoid burns or clothing ignition. Young
children should be carefully supervised when in the
same room as fireplace.
Astria.US.com
3
SPECIFICATIONS
36" MODEL
29"
22 1/2"
14 1/2"
22 1/2"
19"
26 /8"
5
15 /8"
20 1/4"
(Ref.)
5
35 1/4"
4 1/2"
1 1/4"
36" HEARTH
11"
OUTSIDE AIR
ACCESS
67"
61"
49"
58"
GAS LINE
ACCESS
30"
7"
1"
1"
36"
45 1/8"
10 1/2" 9 1/2"
3 1/2"
4 1/2"
7 1/4"
11"
15 1/4"
Figure 1 - 36" Model Oracle36
4
Astria.US.com
126758-01B
SPECIFICATIONS Continued
42" MODEL
30 1/2"
22 3/4"
15 3/4"
26 3/8"
21 3/4"
23"
(Ref.)
29"
17 5/8"
41 3/8"
1 1/4"
42" HEARTH
4 3/8"
5/8"
OUTSIDE
AIR
ACCESS
11"
67" 58"
61"
49"
GAS LINE
ACCESS
30"
10 1/2" 9 1/2"
3 1/2"
7"
1"
42"
51 1/8"
4 1/2"
81/2"
13"
17"
Figure 2 - 42" Model Oracle42
126758-01B
Astria.US.com
5
SPECIFICATIONS Continued
50" MODEL
38 1/2"
24"
19 1/4"
34 3/8"
21 3/4"
28 /2"
1
17 /8"
5
49 3/8"
OUTSIDE
AIR
ACCESS
11"
61"
1 1/4"
50" HEARTH
4 /8"
3
67"
23"
(Ref.)
GAS LINE
ACCESS
58"
49"
30"
10 1/2"
7"
1"
4 1/2"
50"
59"
9 1/2"
3 1/2"
8 1/2"
13"
17"
Figure 3 - 50" Model Oracle50
6
Astria.US.com
126758-01B
FIREPLACE INSTALLATION
SELECTING LOCATION
To determine the safest and most efficient location for the fireplace,
you must take into consideration the following guidelines:
1. The location must allow for proper clearances (see Figures 4 and
5).
2. Consider a location where fireplace will not be affected by drafts,
air conditioning ducts, windows or doors.
3. A location that avoids cutting of joists or roof rafters will make
installation easier.
4. An outside air kit is available with this fireplace (see Optional
Outside Air Kit on page 9).
raised platform, a Z-type ember protector (not supplied) must be
fabricated to fit your required platform height. Ember protector
should extend under fireplace a minimum of 1 1/2". Ember protector
should be made of galvanized sheet metal (28 gauge minimum to
prevent corrosion.
6. Using screws or nails, secure fireplace to framing through flanges
located on sides of fireplace.
Note: For outdoor installations, fireplace enclosure must allow for
adequate drainage and fresh air ventilation. It is recommended that
a sealed, corrosion resistant catch pan with provision for drainage
be installed under fireplace within fireplace enclosure.
MINIMUM CLEARANCE TO COMBUSTIBLES
Back and sides of fireplace 1 1/2" min.
Ceiling 42" min.
Front of fireplace 48" min.
Floor**
0" min.
Perpendicular wall to opening 18" min.
36" Models 12" min.
Top spacers
0" min.
Mantel clearances
see Mantels, page 8
Chimney outer pipe surface 2" min.
36" Model 1" min.
* Not required at nailing flanges
** See step 2 of Framing
67 1/8"
58 1/8"
45 1/4" (36'' Models)
51 1/4" (42'' Models)
59 1/8" (50'' Models)
WARNING: Do not pack required air spaces with
insulation or other materials.
Minimum/Maximum Chimney Height for Residential Installation
Minimum height of chimney, measured from base of fireplace to flue
gas outlet of termination, is 16 feet for straight flue or a flue with one
elbow set. Maximum distance between elbows is 6 feet. For systems
with two elbow sets, minimum height is 22 feet. Maximum height of
any system is 50 feet. This measurement includes fireplace, chimney
sections and height of termination assembly at level of the flue gas
outlet (see Figure 15, page 12).
Minimum/Maximum Chimney Height for Outdoor Installation
28 /4" (36'' Models)
Figure 4 - Framing Dimensions
Maintain 1 1/2"
Clearance
at Sides and
Back of Fireplace
61" (36" Models)
65" (42" Models)
71" (50" Models)
Minimum height of chimney, measured from base of fireplace to flue
gas outlet of termination, is 9.5 feet (minimum of 4 feet of chimney
pipe sections required for outdoor installation).
FRAMING
1. Frame opening for fireplace using dimensions shown in Figures 4
and 5.
2. If fireplace is to be installed directly on carpeting, tile or any
combustible material other than wood flooring, fireplace must
be installed upon a metal or wood panel extending full width and
depth of fireplace.
3. Set fireplace directly in front of this opening and slide unit back
until nailing flanges touch side framing.
4. Check level of the fireplace and shim with sheet metal if necessary.
5. Before securing fireplace to prepared framing, ember protector
(provided) must be placed between hearth extension (not supplied) and under bottom front edge of fireplace to protect against
glowing embers falling through. If fireplace is to be installed on a
126758-01B
30 1/8"
1
Astria.US.com
1 1/2" Clearance
Not Required at
Nailing Flanges
86 1/2" (36" Models)
92" (42" Models)
100" (50" Models)
Figure 5 - Corner Installation
7
FIREPLACE INSTALLATION Continued
Fireplace Front
Seal Gap
Ember Protector
Fireplace Front
Raised Hearth
Ember Protector
Fireplace Front
Elevated
Combustible
Material
12 1/4" Ref.
6"
Ref.
15" Min. (36" Models)
21" Min. (42/50"
Models)
WARNING: Hearth extension is to be installed only
as shown in Figure 6.
MANTELS
A mantel may be installed if desired (see Figure 7). Woodwork such as
wood trims, mantels or any other combustible material projecting from
front face must not be placed within 12" (36" Models) or 18" (42/50" Models) of fireplace opening. Combustible materials above 12" (36" Models)
or 18" (42/50" Models) and projecting more than 1 1/2" from fireplace
must not be placed less than 15" (36" Models) or 21" (42/50" Models)
from the top opening of the fireplace (NFPA STD 211, Sec. 7-3.3.3).
Mantels or any other combustible material also may come up to side
edge of black metal face of fireplace as long as projections from front
face fall within limit shown in Figure 7.
Hearth
Extension
Safe
Zone for
Projection of
Combustible
Materials
33°
3" Nom.
11/2" Max.
12" Min.
(36" Models)
18" Min.
(42/50"
Models)
HEARTH EXTENSION
A hearth extension projecting a minimum of 20" in front of and a
minimum of 12" beyond each side of fireplace opening is required
to protect combustible floor construction in front of fireplace. Fabricate a hearth extension using a material which meets the following
specifications: a layer of noncombustible, inorganic material having a
thermal conductivity of k=0.84 BTU IN/FT, HR. F (or less) at 1" thick.
For example, if the material selected has a k factor of 0.25, such as
glass fiber, the following formula would apply:
0.25 x 1.0" = 0.30" thickness required
0.84
Thermal conductivity "k" of materials can be obtained from manufacturer or supplier of noncombustible material. If hearth extension is
to be covered, use noncombustible material such as tile, slate, brick,
concrete, metal, glass, marble, stone, etc. Provide a means to prevent
hearth extension from shifting and seal gap between fireplace frame
and hearth extension with a noncombustible material (see Figure 6).
Upper
Section of
Fireplace
Fireplace Opening
Top View of Fireplace
Seal Gap
7.75" (36" Models)
11.5" (42/50" Models)
Ember Protector
FIREBOX
SAFE ZONE
Figure 6 - Hearth Extension
33°
Min. to
Perpendicular
Side Wall
12" - 36" Models
18" - 42/50" Models
3" Max.
4.5"
Combustible
Material Must
Not Overlap
Front Face
Figure 7 - Mantel Clearances to Combustible Material
8
Astria.US.com
126758-01B
VENTING INSTALLATION
OPTIONAL OUTSIDE AIR KIT (MODEL AK4/AK4F)
PART NO.
Signature
12-12DM
12-12HT
18-12DM
18-12HT
24-12DM
24-12HT
36-12DM
36-12HT
48-12DM
48-12HT
RLT-12D
RLT-12HT
The installation of an outside air kit should be performed during
the rough framing of the fireplace due to the nature of it's location.
Outside combustion air is accessed through a vented crawl space
(AK4F) or through a sidewall (AK4).
CAUTION: Combustion air inlet ducts shall not
terminate in attic space.
The maximum height for the air vent can not exceed
3 feet below the flue gas outlet of the termination.
Secure to Collars with Metal Tape, Screws
or Straps (Min. of 1/4" x 20" in size)
Vented
Crawl Space
(Check Local
Codes Before
Installing in a
Vented Crawl
Space)
Air Inlet
Location
Must Allow
For Bushes
or Snow
STL-12D
Vent Hood
Required
for Wall
GAIN
66 1/2"
Pipe Section
10 5/8"
Pipe Section
16 5/8"
Pipe Section
23 5/8"
Pipe Section
34 5/8"
Pipe Section
46 5/8"
Round Termination
Square ChaseTop with Slip
Section
7 3/4"*
7" to 15"*
* The lineal gain for the terminations is measured to
the flue gas outlet height.
Installation
15" Galvanized
Outer Pipe
Air Inlet
Eyebrow
12 3/8"
Stainless
Inner Pipe
Figure 8 - Outside Air Kit
CHIMNEY PIPE
Hemmed
End
Figure 9 - Lineal Gain
WARNING: Label part number 900599-01 must
be applied by the installer to all chimney pipe
sections but is not required on sections that will
be visible after the installation is complete. Label
must wrap around the circumference of the pipe.
See accessories, page 25 for Kit F2659.
The IHP chimney system consists of 12", 18", 24", 36" and 48" snaplock, double-wall pipe segments, planned for maximum adaptability
to individual site requirements. Actual lengths gained after fitting
overlaps must be taken into consideration (lineal gain) and are
given in the lineal gain chart (see Figure 9). Lineal Gain is the actual
measurable length of a part after two or more parts are connected.
For Canada, use chimney parts designated "HT".
WARNING: The opening in the collar around the
chimney at the top of the fireplace must not be obstructed. Never use blown insulation to fill the chimney
enclosure.
126758-01B
LINEAL GAIN
DESCRIPTION
Fireplace
ASSEMBLY AND INSTALLATION OF DOUBLE WALL CHIMNEY
SYSTEM
Each double wall chimney section consists of a galvanized outer pipe, a
stainless steel inner flue pipe and a wire spacer. The pipe sections must
be assembled independently as the chimney is installed. When connecting chimney directly to the fireplace, the inner flue pipe section must be
installed first with the lanced side up. The outer pipe section can then
be installed over 5 the flue pipe section with the hemmed end up. Press
down on each pipe section until the lances securely engage the hem on
the fireplace starter. The wire will assure the proper spacing between the
inner and outer pipe sections.
Continue to assemble chimney sections as outlined above, making
sure that both the inner and outer pipe sections are locked together.
When installing double wall snap-lock chimney together, it is important to assure the joint between the chimney sections is locked. Check
by pulling chimney upward after locking. The chimney will not come
apart if properly locked. It is not necessary to add screws to keep the
chimney together (exception, see Figure 10, page 10).
The height of a vertical chimney pipe supported ONLY by the fireplace, must not exceed 20 feet. Chimney heights above 20 feet must
be supported.
Astria.US.com
9
VENTING INSTALLATION Continued
OFFSET
A
4 3/8"
9 3/4"
12 3/4"
15"
18"
21 1/4"
23 3/4"
27 3/4"
30"
33"
36"
38 1/4"
41 1/4"
45"
46 3/4"
51"
53 1/4"
56 1/4"
59 1/4"
61 3/4"
64 3/4"
68 1/4"
70"
74 1/4"
76 3/4"
79 3/4"
RISE
B
16 3/8"
25 1/2"
30 3/4"
34 3/4"
40"
46 1/4"
49 1/4"
56 3/4"
60 3/4"
66"
71"
75"
80 1/4"
86 3/4"
89 1/2"
97"
101"
106 1/4"
111 1/2"
115 1/2"
120 3/4"
127"
130"
137 1/2"
141 1/2"
146 3/4"
CHIMNEY LENGTH
12" 18" 24" 36" 48"
ELBOW SET ONLY
1
1
1
1 1
1
1 1
1
1
1
1
1
1
2
1 1
1
2
1 1
1
1 1
2
2
1
1 1
1
2
1
2
2 1
1 1
2
1
2 1
1
2 1
4
USING ELBOW OFFSETS (30E-12DM)
1. To achieve desired offset, you may install combinations of 12",
18", 24", 36" and 48" length of double wall pipe (see offset chart
and Figure 10).
2. Chimney weight above offset rests on return elbow. Straps must
be securely nailed to rafters or joists (see Figure 11, details A and
B).
3. Maximum length of pipe between supports (return elbow or
12S-12DM) is 6' of angle run. Maximum of two 6' angle run
sections per chimney system (see Figure 12, page 11).
4. All pipe connections between the offset and return must be
secured with two screws on the outer pipe only (see Figure
10). Do not penetrate the inner stainless.
See Detail A
2" Min.
Straps
Straps
Detail B
Angle Firestop
See Detail B
OFFSET CHART (22-50 FT. SYSTEM HEIGHT)
Straps
Straps
Detail A
Return Elbow
Figure 11 - Ceiling Support Pipe 12S-12DM
Screws
B
CAUTION: THE STRUCTURAL INTEGRITY OF THE
MANUFACTURED HOME FLOOR, WALL, AND CEILING/
ROOF MUST BE MAINTAINED.
WARNING: DO NOT INSTALL IN SLEEPING ROOM
OF MOBILE HOMES.
A
Figure 10 - Elbow Offset
10
Astria.US.com
126758-01B
VENTING INSTALLATION Continued
Return
Elbow
Offset
Elbow
Return
Elbow
Offset
Elbow
6' Max.
Return
Elbow
6' Max. Ceiling
Support Pipe
12S-12DM
Return
Elbow
6' Max.
Offset
6' Max. Elbow
Offset
Elbow
Offset
Elbow
A
Return
Elbow
B
6' Max.
6' Max.
C
Figure 12 - Typical Offset Terminations
FIRESTOP SPACERS (FS-10, 1100EFS-10DM FOR 36" MODELS)
Firestop spacers are required at each point where the chimney penetrates
a floor space. Their purpose is to establish and maintain the required
clearance between the chimney and the combustible materials. When
the pipe passes through a framed opening into a living space above, the
firestop must be placed onto the ceiling from below as shown in Figure 13.
They also provide complete separation from one floor space to another
or attic space as required by most codes. When the double wall pipe
passes through a framed opening into an attic space, the firestop must
be placed into an attic floor as shown in Figure 14.
IMPORTANT NOTICE
When penetrating a ceiling into an attic, a firestop
thimble (FST10) is required to avoid intrusion by insulation and recommended to negotiate a joist.
Firestop Thimble FST10
Existing
Ceiling
Frame
Firestop
Spacer
Figure 14a - Firestop Thimble
Screws or
Staples
(Min. of 8)
Figure 13 - Firestop Spacer with Living Space Above Ceiling
Firestop
Spacer
Screws or Staples
(Min. of 8)
Existing
Ceiling
Frame
Figure 14 - Firestop Spacer with Attic Space Above Ceiling
126758-01B
PENETRATING ROOF
To maintain a 1" (36" Models) or 2" (42/50" Models) clearance to the
pipe on a roof with a pitch, a rectangular opening must be cut.
1. Determine center point through which pipe will penetrate roof.
2. Determine center point of roof. Pitch is distance the roof drops
over a given span, usually 12". A 6/12 pitch means that roof drops
6" for each 12" measured horizontally down from roof rafters.
3. Use roof opening chart (Figure 15, page 12) to determine correct
opening length and flashing required.
4. Remove shingles around opening measured. Cut out this section.
5. Add next sections of pipe until end penetrates roof line. Check
to see that proper clearances are maintained. Extend chimney by
adding sections of double wall pipe until pipe is minimum of 30"
above highest point of roof cutout. Termination and chimney must
extend a minimum of 36" above highest point where it passes
through roof.
Astria.US.com
11
VENTING INSTALLATION Continued
17" Min.
30" Min.
1" Min.
1" Min.
1" Min.
Opening "A"
Pitch
Flat
0-6/12
6/1212/12
Slope Opening Used Flashing
"A" Max. Model No.
0°
17"
V6F-10DM
26.6°
19"
V6F-10DM
45.0°
24"
V12F-10DM
Roof Opening 36" Models
19.5" Min.
FLASHING INSTALLATION (V6F-10DM OR V12F-10DM)
Determine the flashing to be used with the roof opening chart. Slide
flashing over pipe until base is flat against roof. Replace as many
shingles as needed to cover exposed area and flashing base. Secure
in position by nailing through shingles (see Figure 16). DO NOT NAIL
THROUGH FLASHING CONE.
Installing Flashing on a Metal Roof
When installing the flashing on a metal roof, it is required that putty
tape be used between the flashing and the roof. The flashing must be
secured to the roof using #8 x 3/4" screws and then sealed with roof
coating to prevent leakage through the screw holes. A roof coating
must also be applied around the perimeter of the flashing to provide
a proper seal.
Storm Collar
Flashing
Cone
Nail Only
Outer
Perimeter
of Flashing
Overlap
Shingles Top
and Sides Only
30" Min.
2" Min.
2" Min.
Underlap Shingles
at Bottom
2" Min.
Figure 16 - Flashing Installation
Opening "A"
Pitch
Slope Opening Used Flashing
"A" Max.
Model No.
Flat
0°
19.5"
V6F-10DM
0-6/12 26.6°
22'
V6F-10DM
6/1245.0°
27"
V12F-10DM
12/12
Roof Opening 42" and 50" Models
Figure 15 - Roof Opening Measurements
Storm Collar Installation (SC2-1)
Place storm collar over pipe and slide down until it is snug against
the open edge of the flashing (see Figure 17). Apply waterproof caulk
around the perimeter of the collar to provide a proper seal.
Chimney
Pipe
Waterproof
Caulk
Storm
Collar
Flashing
Figure 17 - Storm Collar
12
Astria.US.com
126758-01B
VENTING INSTALLATION Continued
Terminations/Spark Arrestor
The fireplace system must be terminated with the listed round top or
chase terminations. In any case, refer to the installation instructions
supplied with the termination.
CAUTION: Do not seal openings on the rooftop
flashing. Follow the installation instructions provided
with the termination being used.
10 FOOT RULE
All flue gas outlet chimney terminations must extend a minimum of
3 feet in height above the highest point where it passes through the
roof and must be at least 2 feet above the highest point of the roof
that is within a horizontal distance of 10 feet (see Figure 20).
Level of
Flue Gas
Outlet
10'
10'
RLT-12D
Stainless
Inner Flue
Pipe
2' Min.
Level of
Flue Gas
Outlet
Secure
Termination
to Outer
Pipe with 3
Screws
2' Min.
Waterproof
Caulking
Storm
Collar
3' Min.
Figure 20 - 10 Foot Rule
Flashing
Overlap
Shingles (Top
and Sides of
Flashing Base)
3' Min.
Underlap
Shingles
FINISHING FIREPLACE
Combustible materials, such as wallboard, sheet rock, drywall, plywood,
etc. may make direct contact with sides and top around the fireplace
face. It is important that combustible materials do not overlap the face
itself. Brick, glass, tile or other noncombustible materials may overlap
the front face provided they do not obstruct essential openings like
louvered slots or any other opening. When overlapping with a noncombustible facing material, use only noncombustible mortar or adhesive.
Figure 18 - Termination
CHASE INSTALLATIONS
Instructions for chase installations are included with the chase style
termination chosen. In a multiple chase installation, be sure to provide
adequate distance between terminations to prevent smoke spillage
from one termination to another. We suggest that terminations be
separated at least 24", center to center and stacked at a vertical height
difference of 18" (see Figure 19).
Note: If a decorative shroud is to be installed, contact the manufacturer
for specifications.
18"
Min.
Typ.
24" Min.
24" Min.
Figure 19 - Multiple Chase Installation
126758-01B
Astria.US.com
13
MOSAIC MASONRY BRICK PANELS AND ESTATE REFRACTORY PANELS INSTALLATION
WARNING
Slot
Right Face
LIFTING HAZARD
SINGLE -PERSON LIFT COULD
CAUSE INJURY.
USE ASSISTANCE WHEN MOVING
OR LIFTING.
NOTE: A Mosaic Masonry or Estate liner is required for use with
your Oracle36, Oracle42, or Oracle50 Firebox. (Not supplied, see
pages 22 and 23 for models available).
Hearth
MOSAIC MASONRY BRICK INSTALLATION
Figure 22 - Slots for Firebrick Walls
IMPORTANT: Installation of brick panels should be
done after the fireplace is placed in a permanent
location.
4. Secure the firebrick wall using 2 of the retainers provided. The
bracket will slip underneath the metal lip on the top of the wall
and screw into the inner dome of the fireplace (Figure 23).
Note: Remove grate, screen assemblies and all hardware components
out of the box prior to installation.
INSTALLATION
1. Install bottom brick panel. Using at least two people, hold bottom brick panel by its side edges. Place the back edge of bottom
panel into the firebox first and carefully lower the front edge of
panel. Make sure bottom panel is centered in the firebox and
flush with the front of the fireplace. Be careful not to pinch your
fingers between the panel and firebox (Figure 21).
2. Install the left and right side leading bricks (Figure 21).
Retaining
Bracket
Right Wall
Leading
Brick
Side leading
brick Panel
Figure 23 - Installing Side Walls
Hearth Panel
Figure 21 - Installing Hearth and Leading Brick panels
3. Install the left and right firebrick walls. There is a bracket with 2
tabs on the bottom of each firebrick wall. Angle the wall into the
fireplace opening and into the slots on the side of the hearth (Figure 22), then tilt the top of the panel toward the firebox surround.
14
5. Install the rear firebrick wall last. Place the wall face side down
on the hearth with the bottom of the wall toward the rear of the
firebox and the top toward the front of the fireplace. Tilt the wall
up toward the back of the firebox. Secure with 2 rear retaining
brackets provided (Figure 24, page 15).
6. It is recommended that the joints between all firebrick walls
be grouted for a more finished look, see grouting instructions. For more information and to watch a how to video go
to Astria.US.com and select Technical Support.
Astria.US.com
126758-01B
MOSAIC MASONRY BRICK PANELS AND ESTATE REFRACTORY PANELS INSTALLATION Continued
INSTALLING SCREEN
Retaining Bracket
1. Slide round end of screen rod into rings at top of screen. Attach
one push-on nut to end of rod before attaching last ring of screen.
2. Insert the round end screen rod into hole on the left and right
side of smoke shelf (Figure 25).
3. Mount flat end of screen rod with #10 x 5/8" to center of smoke
shelf.
4. Install other screen rod in same manner.
Rating Plate
Hole for Screen Rod
Leading
Bricks
Figure 24 - Installing Rear Wall
GROUTING INSTRUCTIONS
Note: Grouting material provided with mosaic brick kit
1. Moisten brick surface with damp sponge or spray bottle just prior
to application. When bricks are wet, any excess grout mixture
on bricks will easily wipe off.
2. In a heavy duty mixing bucket, add equal parts cement and sand.
Add enough water and mix together well using a power drill with
mixing wand attachment to a yogurt like consistency. Not adding
enough water can lead to grout falling out after burning.
3. The overall length of piping bag should be about 16". If the bag is
longer than 16", cut it down to size by removing end with larger
opening. This will make the bag easier to handle.
4. Put grout mixture into piping bag making sure the smaller
opening is downward and over a moist towel to avoid spilling.
Place a wet towel over the bucket making sure it is directly on
the surface of grout mixture. This will keep the mixture moist
and it will not dry out before use.
5. Grout all joints where two firebrick walls come together.
6. Using a trowel, remove excess grout mixture by moving trowel
in the direction of the joint. Grout mixture in the joint should now
be flush with brick surface. If not enough grout is applied into
each space, grout may fall out after burning.
7. Using a joint striker, smooth out grout line. Allow 72 hours
before operating fireplace.
Figure 25 - Installing Fireplace Screen
INSTALLING GRATE RETAINERS
1. Place the provided grate retainers on the hearth as shown in Figure 26. The back of the retainer will be flush with the rear firebrick
wall. Mark the center of the hole on the hearth with a marker.
2. Drill two holes in the hearth in the marked locations using a
masonry 3/16" drill bit.
3. Secure grate retainer with masonry screws provided.
WARNING: Risk of fire! Replace grate with IHP
approved grate only. The grate has been designed
to keep the operation of your fireplace safe and
efficient.
Figure 26 - Installing Grate Retainers
126758-01B
Astria.US.com
15
MOSAIC MASONRY BRICK PANELS AND ESTATE
REFRACTORY PANELS INSTALLATION Continued
ESTATE REFRACTORY PANELS INSTALLATION
Note: Remove grate, screen assemblies and all hardware components
out of the box prior to installation.
1. Install bottom brick panel. Using at least two people, hold bottom brick panel by its side edges. Place the back edge of bottom
panel into the firebox first and carefully lower the front edge of
panel. Make sure bottom panel is centered in the firebox and
flush with the front of the fireplace. Be careful not to pinch your
fingers between the panel and firebox.
2. Position "Z" shape retaining brackets on top of the notched area
toward the rear of the bottom brick panel. Grate retaining bracket
should be positioned as shown in Figure 26, page 14.
3. Install rear brick panel. This panel has a top and bottom side.
To determine correct position, match up the pattern on the rear
panel with the right and left brick panels before installing. Make
sure rear panel is centered before continuing.
4. Install the right and left brick panels with the gas line knock outs
placed down toward the bottom refractory. Align the right an left
brick panels with the rear panel so the grout lines line up.
5. Install upper corner brackets and tighten set screws (see Figure
26A).
6. Install grate by placing rear legs into slots in the grate retainer
(see Figure 26A)
LEFT BRICK
PANEL
UPPER CORNER
BRACKET (2x)
REAR BRICK
PANEL
GRATE
GRATE RETAINER
BRACKET (2x)
OPTIONAL GAS LINE INSTALLATION
Gas line hook up should be done by your supplier or a qualified
service person.
Note: Before you proceed, make sure your gas supply is turned off.
Use only a 1/2" black iron pipe and appropriate fittings.
1. Remove knockout indentation on refractory or firebrick wall located above refractory hearth floor. Knockout indentation must be
firmly tapped with any solid object such as a 1/2" dowel until it is
released. Remove fragmented portions of refractory (see Figure
27).
2. Remove gas line cover plate located on either side of fireplace and
pull out insulation from gas line conduit sleeve. Save insulation for
reuse. Replace screws.
3. Run a 1/2" black iron gas line into fireplace through the rear at gas
line conduit sleeve (if using a raised platform, add height). Provide
sufficient gas line into fireplace chamber for fitting connection (see
Figure 28, page 17).
Note: Secure incoming gas line to wood framing to provide rigidity for
threaded end.
4. Repack insulation around gas line and into sleeve opening. Seal any
gaps between gas line and refractory knockout hole with refractory
cement or commercial furnace cement, Install the gas appliance or
cap-off gas line if desired.
CAUTION: All gas piping and connections must be
tested for leaks after the installation is completed.
After ensuring that the gas valve is on, apply soap and
water solution to all connections and joints. Bubbles
forming show a leak. Correct all leaks at once. DO NOT
USE AN OPEN FLAME FOR LEAK TESTING AND DO NOT
OPERATE ANY APPLIANCE IF A LEAK IS DETECTED.
LEAK TESTING SHOULD BE DONE BY A QUALIFIED
SERVICE PERSON.
WARNING: Do not operate an unvented gas log set in
this fireplace with the chimney removed.
RIGHT BRICK
PANEL
Outside of
Fireplace
BOTTOM
BRICK PANEL
ASH PANEL
Figure 26A- Installing Refractory Panels
Gas Line
Conduit
Insulation
Remove
Knockout
Side
Firebrick
Finished
Side
1/2" Dowel
Gas
Conduit
Cover
Brick with
Access
Hole
Figure 27 - Gas Line Access
16
Astria.US.com
126758-01B
OPTIONAL GAS LINE INSTALLATION Continued
Outside of
Fireplace
Incoming
1/2" Black
Iron Pipe
Gas Line
Conduit
Repack
Insulation
Seal
Opening
with
Refractory
Cement
Side
Firebrick
Finished
Side
GLASS DOOR INSTALLATION
DOOR FRAME MODELS
Provide Enough
Threaded
End for Fitting
Connection
BDMO36E/G/C, BDMO42E/G/C AND BDMO50E/G/C
Installation
1. Remove screws from smoke shelf (see Figure 29).
2. Mount top door frame and secure with screws provided (see
Figure 29).
3. Place bottom door frame on top of ash lip at front of fireplace
(see Figure 30).
4. Secure bottom door frame to brick with two hex screws provided
as shown in Figure 30 using a 7/16" open end or adjustable
wrench.
Top Door
Frame
Smoke
Shelf
Figure 28 - Gas Line Installation
A gas line or gas log lighter may be installed for the purpose of installing
a vented or vent-free decorative gas appliance incorporating an automatic
shutoff device and complying with the Standard for Decorative Gas Appliances for Installation in Vented Fireplaces, ANSI Z21.60 or American
Gas Association draft requirements for Gas Fired Log Lighters for Wood
Burning Fireplaces, Draft NO. 4 dated August, 1993.
If you install a decorative gas appliance (vented gas log), the decorative gas appliance must comply with the Standard for Decorative
Gas Appliance for Installation in Solid Fuel Burning Fireplaces, ANS
Z21.60 or Z21.84 and shall also be installed in accordance with the
National Fuel Gas Code, ANSI 7223NFPA 54 latest edition.
If you wish to install an unvented (vent-free) gas log set, only unvented
gas log sets which have been found to comply with the standard for
unvented room heaters, ANSI Z21.11.2 are to be installed in this
fireplace.
Figure 29 - Installing Top Door Frame
Ash Lip
WARNING: If the fireplace has been used for wood
burning, the firebox and chimney must be cleaned
of soot, creosote and ashes be a qualified chimney
cleaner. Creosote will ignite if heavily heated.
Bottom
Door
Frame
WARNING: When using a decorative vented gas log,
the damper must be removed or permanently locked in
the fully open position and the glass doors must be in
the fully open position.
Ash Lip
Hex
Screw
Figure 30 - Installing Bottom Door Frame
WARNING: Discontinue use of the appliance immediately if doors are damaged and contact a qualified installer for repair. Only doors certified with the
appliance shall be used.
WARNING: Do not slam or strike doors. Damage
can result in a hazardous condition.
126758-01B
Astria.US.com
17
GLASS DOOR INSTALLATION Continued
OPERATION AND MAINTENANCE GUIDELINES
INSTALLING GLASS DOORS
Spring clips have been installed but some adjustments may be
needed. Install the doors using the following steps:
1. With bifold doors completely folded, insert bottom pivot pin into
pivot hole located near bottom corner of front face opening and
swing door to vertical position making sure top pins slide into
door track. Door is installed when top door pin snaps into spring
clip.
2. Repeat step 1 for remaining door.
If you find the doors do not close properly or do not appear level or
straight, proceed with section on door adjustment,
Fold Door
and Slide
Top Pins
Into Track
Spring
Clip
Insert Pin
into Spring
Clip
GLASS DOORS
Glass doors are optional with the fireplace. When fireplace is in operation,
doors must be fully opened or fully closed position only or a fire hazard
may be created (see Figure 33, page 19).
A fireplace equipped with glass doors operates much differently than a
fireplace with an open front. A fireplace with glass doors has a limited
amount of air for combustion.
Excessive heat within the fireplace can result if too large a fire is built or
if combustion air gate is not completely open. The following tips should
be followed to assure that both the fireplace and glass door retain their
beauty and function properly. Both the flue damper and glass doors must
be fully opened before starting fire. This will provide sufficient combustion
air and maintain safe temperatures in firebox.
IMPORTANT: The glass must be allowed to warm slowly and evenly.
The tempered glass will withstand a gradual temperature rise to 550° F,
which is more than a normal fire will generate. Such materials as pitch/
wax laden logs, very dry mill end lumber and large amounts of paper or
cardboard boxes can create an excessively hot fire and should not be
burned in this fireplace. Always keep the fire well back from the doors
and never allow flames to contact the glass.
WARNING: Fireplaces equipped with glass doors
should be operated only with doors fully opened or
doors fully closed. Doors, if left partly open, may draw
gas and flame out of the fireplace opening creating
risks of both fire and smoke.
Insert
Bottom
Pivot Pin
into Hole
Pivot
Hole
WARNING: Do not slam or strike doors. Damage
can result in a hazardous condition.
Figure 31 - Installing Bi-Fold Doors
DOOR ADJUSTMENT
Remove doors and slightly loosen lower pivot clips and upper spring
clips. Replace doors and fully close them. Use 1/8" shims (any material) to level doors. Once proper setting is achieved, carefully open
doors enough so that you can access spring clips with a phillips
screwdriver. Tighten screws. See Figure 32.
WARNING: Discontinue use of the appliance immediately if doors are damaged and contact a qualified
installer for repair. Only doors certified with the appliance shall be used.
Cleaning Glass
Clean glass with any commercial glass cleaner or soap and water. Do
not use any abrasive material to clean glass. Do not clean glass with any
cool water if glass is still hot from the fire and smoke.
Figure 32 - Adjusting Bi-Fold Doors
18
Astria.US.com
126758-01B
OPERATION AND MAINTENANCE GUIDELINES Continued
TECHNICAL SERVICE
You may have further questions about installation, operation, or
troubleshooting. Please contact your IHP dealer for any questions
or concerns a. When contacting your dealer please have your model
and serial numbers of your fireplace ready. You can also visit our
web site at Astria.US.com.
Doors Fully Closed
REPLACEMENT PARTS
Fireplace Front
See Pages 20 to 21 for a complete replacement parts list. Use only
parts supplied from the manufacturer.
Normally, all parts should be ordered through your IHP distributor
or dealer. Parts will be shipped at prevailing prices at time of order.
When ordering repair parts, always give the following information:
1. The model number of the fireplace.
2. The serial number of the fireplace.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the fireplace.
Doors
Fully Opened
Fireplace Front
If you encounter any problems or have any questions concerning the
installation or application of this fireplace, please contact your dealer.
Figure 33 - Bi-Fold Glass Doors
OUTSIDE AIR AND DAMPER HANDLE OPERATION
The damper handle, which opens and closes the damper blade, is
located in the upper front face of the fireplace. Pushing the handle
forward and up through the keyway slot will free damper blade to
automatically open. Pushing the handle forward and down will lock
damper blade closed (see Figure 34). Damper must be locked in the
full open position before operating fireplace (see Figure 34).
IHP
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
Visit us at Astria.US.com
Damper
Weight
To Close
Damper
Damper
Weight
To Open
Damper
Figure 34 - Operating Damper Handle
126758-01B
Astria.US.com
19
PARTS
MODELS 36", 42", AND 50"
MODEL
Oracle36
Oracle42
Oracle 50
CATALOG NO.
F0535
F0536
F0537
10
8
7
6
9
5
11
12
20
21
14
4
13
22
16/17
15
1
2
19
24
23
3
18
25
20
Astria.US.com
126758-01B
PARTS
This list contains replaceable parts used in your firebox. When ordering parts, follow the instructions listed under Replacement Parts on
page 19 of this manual.
WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved
by IHP. Use of non-approved parts can result in poor performance and safety hazards.
KEY NO.
1
2
3
4
5
6
7
8
9
DESCRIPTION
Oracle36 Oracle42 Oracle50 QTY.
FACE ASSEMBLY
•
•
•
1
FIREBOX BOTTOM ASSEMBLY
•
•
•
1
FIREBOX BOTTOM
•
•
•
1
FIREBOX SURROUND
•
•
•
1
OUTER DOME ASSEMBLY
•
•
•
1
INSULATION PAN SUPPORT
•
•
•
1
INSULATION PAN
•
•
•
1
TOP INSULATION
•
•
•
1
ASSY, TOP FIREPLACE 36"
•
1
FIREPLACE TOP ASSEMBLY, 42"
•
1
FIREPLACE TOP ASSEMBLY, 50"
•
1
10
SPACER, FIREPLACE TOP 42MC
•
•
•
4
11
FIREPLACE SURROUND ASSEMBLY
•
•
•
1
12
SPACER, CLEARANCE 36/42/50"
•
•
•
6
13
BRACKET, F/P HANDLE
•
•
•
4
14
PLATE,OUTSDE AIR COVER 36E44-6
•
•
•
2
15
COVER, GAS CONDUIT PLATE 36E
•
•
•
4
16
GAS, CONDUIT ONE
•
•
•
2
17
GAS, CONDUIT TWO
•
•
•
2
18
HEAT SHIELD SUPPORT
•
•
•
1
19
ASSY, ASH BOX "ALPHA"
•
•
•
1
20
INNER DOME ASSEMBLY
•
•
•
1
21
SMOKE SHIELD
•
•
•
1
22
DAMPER CONTROL BRACKET
•
•
•
1
23
SCREEN 36" STAINLESS
•
2
SCREEN 42" STAINLESS
•
2
SCREEN 50" STAINLESS
•
2
24
ROD, SCREEN FORMED S.S.
•
2
ROD, SCREEN FORMED S.S.
•
2
ROD, SCREEN FORMED S.S.
•
2
25
ASSEMBLY, GRATE S.S.
•
1
ASSEMBLY, GRATE S.S.
•
1
ASSEMBLY, GRATE S.S.
•
1
PARTS AVAILABLE NOT SHOWN
124174-02 GRATE RETAINER STAINLESS
•
•
•
2
J4357
SPACER, REFRACTORY 36
•
•
•
4
114913-01 REAR FIREBRICK WALL SPACERS
•
•
•
2
** Not a field replaceable part.
126758-01B
CATALOG NO.
**
**
**
**
**
**
**
**
**
**
**
J6997
**
J4362
J5329
J6900
J6934
J4368
J4369
**
J6020
**
**
**
117556-03
117556-02
117556-01
J5310
J5309
J5308
J5303
J5302
J5301
Astria.US.com
21
PARTS
MOSAIC MASONRY BRICK KITS
A Mosaic Masonry or Estate liner is required for use with your Oracle36, Oracle42, or Oracle50 Firebox. Catalog numbers are included
for convenience.
WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved
by IHP. Use of non-approved parts can result in poor performance and safety hazards.
CATALOG NO. MODEL NO.
F0334
Mosaic36M2
F0335
Mosaic36M4
F0336
Mosaic36M2
F0337
Mosaic36M4
F0338
Mosaic36M3
F0339
Mosaic36M5
F0340
Mosaic36M3
F0341
Mosaic36M5
F0342
Mosaic42M2
F0343
Mosaic42M4
F0344
Mosaic42M2
F0345
Mosaic42M4
F0346
Mosaic42M3
F0347
Mosaic42M5
F0348
Mosaic42M3
F0349
Mosaic42M5
F0350
Mosaic50M2
F0351
Mosaic50M4
F0352
Mosaic50M2
F0353
Mosaic50M4
F0354
Mosaic50M3
F0355
Mosaic50M5
F0356
Mosaic50M3
F0357
Mosaic50M5
DESCRIPTION
Red Full Stacked
Red Split Stacked
Ivory Full Stacked
Ivory Split Stacked
Red Herr Full
Red Herr Split
Ivory Herr Full
Ivory Herr Split
Red Full Stacked
Red Split Stacked
Ivory Full Stacked
Ivory Split Stacked
Red Herr Full
Red Herr Split
Ivory Herr Full
Ivory Herr Split
Red Full Stacked
Red Split Stacked
Ivory Full Stacked
Ivory Split Stacked
Red Herr Full
Red Herr Split
Ivory Herr Full
Ivory Herr Split
WARNING
LIFTING HAZARD
SINGLE -PERSON LIFT COULD
CAUSE INJURY.
USE ASSISTANCE WHEN MOVING
OR LIFTING.
22
IMPORTANT: Installation of brick panels should be
done after the fireplace is placed in a permanent
location.
Astria.US.com
126758-01B
PARTS
ESTATE LINERS
An Estate or Mosaic Masonry liner is required for use with your Oracle36, Oracle42, or Oracle50 Firebox. Catalog numbers are included
for convenience.
WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved
by IHP. Use of non-approved parts can result in poor performance and safety hazards.
CATALOG NO. MODEL NO.
F0358
Estate36P2
F0359
Estate36P2
F0360
Estate36P2
F0361
Estate36P2
F0362
Estate36P3
F0363
Estate36P3
F0364
Estate36P3
F0365
Estate36P3
F0366
Estate42P2
F1367
Estate42P2
F0368
Estate42P2
F0369
Estate42P2
F0370
Estate42P3
F0371
Estate42P3
F0372
Estate42P3
F0373
Estate42P3
F0374
Estate50P2
F0375
Estate50P2
F0376
Estate50P2
F0377
Estate50P2
F0378
Estate50P3
F0379
Estate50P3
F0380
Estate50P3
F0381
Estate50P3
DESCRIPTION
Stacked "Rust"
Stacked "Cappuccino"
Stacked "Creamer"
Stacked "Gray"
Herringbone "Rust"
Herringbone "Cappuccino"
Herringbone "Creamer"
Herringbone "Gray"
Stacked "Rust"
Stacked "Cappuccino"
Stacked "Creamer"
Stacked "Gray"
Herringbone "Rust"
Herringbone "Cappuccino"
Herringbone "Creamer"
Herringbone "Gray"
Stacked "Rust"
Stacked "Cappuccino"
Stacked "Creamer"
Stacked "Gray"
Herringbone "Rust"
Herringbone "Cappuccino"
Herringbone "Creamer"
Herringbone "Gray"
WARNING
LIFTING HAZARD
SINGLE -PERSON LIFT COULD
CAUSE INJURY.
USE ASSISTANCE WHEN MOVING
OR LIFTING.
126758-01B
IMPORTANT: Installation of brick panels should be
done after the fireplace is placed in a permanent
location.
Astria.US.com
23
ACCESSORIES
BI-FOLD GLASS DOORS (For Use With Mosaic Brick Only)
CAT NO.
MODEL
DESCRIPTION
F1011
BDMO36E
GLASS DOOR, 36" EBONY
F1012
BDMO36G
GLASS DOOR, 36" PEWTER
F1013
BDMO36C
GLASS DOOR, 36" OILED BRONZE
F1014
BDMO42E
GLASS DOOR, 42" EBONY
F1015
BDMO42G
GLASS DOOR, 42" PEWTER
F1016
BDMO42C
GLASS DOOR, 42" OILED BRONZE
F1020
BDMO50E
GLASS DOOR, 50" EBONY
F1021
BDMO50G
GLASS DOOR, 50" PEWTER
F1022
BDMO50C
GLASS DOOR, 50" OILED BRONZE
BI-FOLD GLASS DOORS (For Use With Estate Refractory Panels Only
F1002
BDG36
GLASS DOOR, 36" BLACK
F1003
BDG36B
GLASS DOOR, 36" BRUSHED BRASS
F1004
BDG36P
GLASS DOOR, 36" PLATINUM
F1005
BDG42
GLASS DOOR, 42" BLACK
F1006
BDG42B
GLASS DOOR, 42" BRUSHED BRASS
F1007
BDG42P
GLASS DOOR, 42" PLATINUM
F1008
BD50
GLASS DOOR, 50" BLACK
F1009
BD50B
GLASS DOOR, 50" BRUSHED BRASS
F1010
BD50P
GLASS DOOR, 50" PLATINUM
DOUBLE WALL PIPE
F0932
12-12DM
12" Section Double Wall Pipe Snap Lock
F0933
18-12DM
18" Section Double Wall Pipe Snap Lock
F0934
24-12DM
24" Section Double Wall Pipe Snap Lock
F0935
36-12DM
36" Section Double Wall Pipe Snap Lock
F0936
48-12DM
48" Section Double Wall Pipe Snap Lock
F0953
12-12HT
12" Section Hi-Temp Double Wall Pipe Snap Lock
F0954
18-12HT
18" Section Hi-Temp Double Wall Pipe Snap Lock
F0955
24-12HT
24" Section Hi-Temp Double Wall Pipe Snap Lock
F0956
36-12HT
36" Section Hi-Temp Double Wall Pipe Snap Lock
F0957
48-12HT
48" Section Hi-Temp Double Wall Pipe Snap Lock
30° OFFSET AND RETURN
F0937
30E-12DM
30 Degree Offset and Return
F0958
30E-12HT
30 Degree Hi-Temp Offset and Return
OPTIONAL OUTSIDE AIR KIT FOR FLOOR INSTALLATION
F1091
24
AK4
Complete Outside Air Kit w/Collars Hood & 3' Flex
Astria.US.com
126758-01B
ACCESSORIES Continued
OPTIONAL OUTSIDE AIR KIT FOR SIDEWALL INSTALLATION
F1093
AK4F
Outside Air Kit Collar, Hood & 3' Flex for Floor Venting
STORM COLLAR
F0946
SC2-1
Storm Collar
FIRESTOP SPACER
J4384
1100EFS-10DM
1" Clearance Firestop Spacer
F0940
FS-10
2" Clearance Firestop Spacer
ROOF FLASHING
F0942
V6F-10DM
Roof Flashing 0 to 6/12 Pitch
F0943
V12F-10DM
Roof Flashing 6/12 to 12/12 Pitch
SQUARE CHASE-TOP TERMINATION
F0948
STL-12D
F0949
STL-12DMP
Square Top Termination with Slip Section
Square Top Termination with Slip Section (Pre-Painted
Black)
ROUND TOP TERMINATIONS
F0947
RLT-12D
Round Top Termination with Louvered Screen
F0960
RLT-12HT
Hi-Temp Round Top Termination with Louvered Screen
FIRESTOP THIMBLE
F0944
FST10
Firestop Thimble
EMBER PROTECTOR
J6906
Protector, Ember EP36
LABEL-UL127-50PK
F2659
126758-01B
LABEL-UL12750PK
WARNING
HOT
WARNING
HOT
WARNING
HOT
• Fire Risk
• Fire Risk
• Fire Risk
• Insulation and combustibles must not touch • Insulation and combustibles must not touch • Insulation and combustibles must not touch
pipe
pipe
pipe
• Consult manual for clearance requirements • Consult manual for clearance requirements • Consult manual for clearance requirements
• Ensure proper connection
• Ensure proper connection
• Ensure proper connection
900599-01
UL127 Venting Label - 50 PK
Astria.US.com
25
IMPORTANT NOTICES
Canadian code CAN/ULC-S610-M87 and other
pertinent codes require stainless steel chimney for
the installation of this fireplace. A Cold Air Climate Kit
is also required in Canada and is recommended for
cooler regions in the United States. Below, find a list of
approved stainless steel parts.
Chimney Parts List for Canada
Catalog
No.
Model No.
8" Hi-Temp
Wood burning Chimney
F0953
12-12HT
12" Section Double Wall Pipe
F0954
18-12HT
18" Section Double Wall Pipe
F0955
24-12HT
24" Section Double Wall Pipe
F0956
36-12HT
36" Section Double Wall Pipe
F0957
48-12HT
48" Section Double Wall Pipe
F0958
30E-12HT
30" Offset and Return
F0959
12S-12HT
Chimney Support
F0960
RLT-12HT
Round Top w/ Louvers
F0961
AP-12HT
Anchor Plate/Collar Assembly
(Masonry Fireplaces)
F0951
CAK-12
Cold Air Collar Kit
IMPORTANT NOTICE
A manufactured shroud which
has been approved by a national
testing agency for use with this
fireplace may be used if installed
in accordance with the instructions by its manufacturer. A
locally fabricated shroud may be
used with IHP Shroud Leg Spacer
Kit (SLK) in accordance with
instructions provided with the
shroud.
NOTICE: The firebox canopy (hood)
must not be modified or replaced with
a canopy that may be provided with
the unvented decorative room heater.
CAUTION: THE STRUCTURAL INTEGRITY OF
THE MANUFACTURED HOME FLOOR, WALL,
AND CEILING/ROOF MUST BE MAINTAINED.
WARNING: DO NOT INSTALL IN SLEEPING
ROOM OF MOBILE HOMES.
*When ordered alone, this part cannot ship via parcel
delivery services.
26
Astria.US.com
126758-01B
Innovative Hearth Products
Astria® Brand Wood-Burning Fireplace
20 Year Limited Warranty
THE WARRANTY
Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your Astria® brand wood burning fireplace ("Product") to be free from defects in materials and workmanship at the time of manufacture. The Product body, firebox and ceramic glass carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited Warranty
against thermal breakage only. After installation, if covered components manufactured by IHP are found to be defective in materials or workmanship during the 20 Year
Limited Warranty period and while the Product remains at the site of the original installation, IHP will, at its option, repair or replace the covered components. If repair or
replacement is not commercially practical, IHP will, at its option, refund the purchase price or wholesale price of the IHP product, whichever is applicable. IHP will also
pay IHP prevailing labor rates, as determined in its sole discretion, incurred in repairing or replacing such components for up to five years. THERE ARE EXCLUSIONS AND
LIMITATIONS to this 20 Year Limited Warranty as described herein.
COVERAGE COMMENCEMENT DATE
Warranty coverage begins on the date of purchase. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six
months after the sale of the Product by an independent IHP dealer/distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the
date of product shipment from IHP, regardless of the installation or occupancy date.
EXCLUSIONS AND LIMITATIONS
This 20 Year Limited Warranty applies only if the Product is installed in the United States or Canada and only if operated and maintained in accordance with the printed
instructions accompanying the Product and in compliance with all applicable installation and building codes and good trade practices.
This warranty is non-transferable and extends to the original owner only. The Product must be purchased through a listed supplier of IHP and proof of purchase must be
provided. The Product body and firebox carry the 20 Year Limited Warranty from the date of installation. Vent components, trim components, paint and applied stains are
excluded from this 20 Year Limited Warranty. The following do not carry a 20 Year Limited Warranty but are warranted as follows:
Air tubes, baffles and brick retainers – Repair or replacement for one year from the date of installation
Cast iron parts – Replacement for one year from date of installation
Electrical components – Repair or replacement for one year from the date of installation
Fireplace screens, refractory and side shields (metal or refractory) – Repair or replacement for two years from date of installation. Excludes hairline cracks.
Fuel grates –These parts are considered consumable accessories and therefore are not warranted, with the exception of defects in material or workmanship which
are covered for 90 days from the date of installation
Gaskets – Replacement for one year from date of installation
Gold & nickel plating – Replacement for two years from date of installation. Excludes tarnishing
Optional glass doors – Repair or replacement for 90 days from the date of installation
Labor coverage – Prevailing IHP labor rates apply for the warranty period of the component.
Parts not otherwise listed carry a 90 day warranty from the date of installation.
Whenever practicable, IHP will provide replacement parts, if available, for a period of 10 years from the last date of manufacture of the Product.
IHP will not be responsible for: (a) damages caused by normal wear and tear, accident, riot, fire, flood or acts of God; (b) damages caused by abuse, negligence, misuse, or
unauthorized alteration or repair of the Product affecting its stability or performance. (The Product must be subject to normal use with approved fuels listed in the Operation
Manual provided with the product. This includes burning such fireplace fuels as wood and natural or propane gas. Fuel products with abnormal burning characteristics,
including but not limited to fuel such as driftwood, coal or plywood and wood products using a binder may burn at excessive temperatures and may cause damage to the
Product or may cause it to function improperly.); (c) damages caused by failing to provide proper maintenance and service in accordance with the instructions provided with
the Product; (d) damages, repairs or inefficiency resulting from faulty installation or application of the Product.
Coverage of this 20 Year Limited Warranty is conditional upon use of an adequate fuel grate on factory-built fireplaces only, when applicable.
IHP is not responsible for inadequate fireplace system draft caused by air conditioning and heating systems, mechanical ventilation systems, or general construction conditions which may generate negative air pressure in the room in which the appliance is installed. Additionally IHP assumes no responsibility for smoking conditions caused by
inadequate chimney height, adjoining trees or buildings, adverse wind conditions or unusual environmental factors and conditions. Certain IHP Products are listed for use with
Security Chimneys International, Ltd. or IHP chimney systems only. Use of chimney components other than that specified in the Product manual will void the Product warranty.
This 20 Year Limited Warranty covers only parts and labor as provided herein. In no case shall IHP be responsible for materials, components or construction which are
not manufactured or supplied by IHP or for the labor necessary to install, repair or remove such materials, components or construction. Additional utility bills incurred due
to any malfunction or defect in equipment are not covered by this 20 Year Limited Warranty. All replacement or repair components will be shipped F.O.B. from the nearest
stocking IHP factory.
LIMITATION ON LIABILITY
It is expressly agreed and understood that IHP’s sole obligation and the purchaser’s exclusive remedy under this warranty, under any other warranty, expressed or implied,
or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified herein.
In no event shall IHP be liable for any incidental or consequential damages caused by defects in the Product, whether such damage occurs or is discovered before or after
replacement or repair, and whether such damage is caused by IHP’s negligence. IHP has not made and does not make any representation or warranty of fitness for a particular
use or purpose, and there is no implied condition of fitness for a particular use or purpose.
IHP makes no expressed warranties except as stated in this 20 Year Limited Warranty. The duration of any implied warranty is limited to the duration of this expressed warranty.
No one is authorized to change this 20 Year Limited Warranty or to create for IHP any other obligation or liability in connection with the Product. Some states and provinces
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. The provisions of this 20 Year
Limited Warranty are in addition to and not a modification of or subtraction from any statutory warranties and other rights and remedies provided by law.
INVESTIGATION OF CLAIMS AGAINST WARRANTY
IHP reserves the right to investigate any and all claims against this 20 Year Limited Warranty and to decide, in its sole discretion, upon the method of settlement.
To receive the benefits and advantages described in this 20 Year Limited Warranty, the appliance must be installed and repaired by a licensed contractor approved by IHP.
Contact IHP at the address provided herein to obtain a listing of approved dealers/distributors. IHP shall in no event be responsible for any warranty work done by a
contractor that is not approved without first obtaining IHP's prior written consent.
HOW TO REGISTER A CLAIM AGAINST WARRANTY
In order for any claim under this warranty to be valid, you must contact the IHP dealer/distributor from which you purchased the product. If you cannot locate the dealer/
distributor, then you must notify IHP in writing. IHP must be notified of the claimed defect in writing within 90 days of the date of failure. Notices should be directed to the
IHP Warranty Department at 1508 Elm Hill Pike, Suite 108; Nashville, TN 37210 or visit our website at WWW.ASTRIA.US.COM.
Printed in U.S.A. © 2013 Innovative Hearth Products
126758-01B
P/N
900202-00, Rev. A 10/2015
Astria.US.com
Innovative Hearth Products
27
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
WARRANTY
KEEP THIS WARRANTY
Model Number
Serial Number
Date Installed
Dealer's Name
Dealer's Phone Number
Keep receipt for warranty verification
IHP reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor
for fireplace code information.
P126758-01
Printed in U.S.A. © 2014 IHP LLC
P/N 126758-01 Rev. B 10/2015.
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021