CHARGER SAFETY WARNINGS THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR BATTERY CHARGER. 1. 2. 3. 4. 5. ECO CHARGER 6. 7. ORIGINAL INSTRUCTIONS 8. SPECIFICATIONS Input: Output: Battery Charge Time: 9. 110-240V AC 50-60Hz 21V DC, 800mA 2.0Hrs - PXBP-150U (18V 1.5Ah) 2.5Hrs - PXBP-200U (18V 2.0Ah) 4.0Hrs - PXBP-300U (18V 3.0Ah) 5.0Hrs - PXBP-400U (18V 4.0Ah) 6.5Hrs - PXBP-520U (18V 5.2Ah) 10. 11. 12. 13. 14. ozito-diy.co.uk 15. 16. 17. Before using the charger read all instructions and cautionary markings on the charger, battery pack and the product using the battery pack. This charger is not intended for any uses other than charging rechargeable batteries. Any other use may result in risk of fire, electric shock or electrocution. Do not place any object on top of the charger or place the charger on a soft surface that may result in excessive internal heat. Place the charger in a position away from any heat source. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when disconnecting the charger. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in the risk of fire, electric shock or electrocution. Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Have it checked by an electrician or power tool repairer. Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire. To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning. Removing the battery pack will not reduce this risk. Never attempt to connect 2 chargers together. DO NOT store or use the tool and battery pack in locations where the temperature may reach or exceed 40ºC (such as inside sheds or metal buildings in summer). The charger is designed to operate on standard household electrical power (240 volts). Do not attempt to use it on any other voltage! The battery pack is not fully charged out of the carton. First read the safety instructions and then follow the charging notes and procedures. The longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 18 - 24ºC. Do not charge the battery pack in an air temperature below 10ºC or above 40ºC. This is important and will prevent damage to the battery pack. Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The battery can explode in a fire. Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, immediately discontinue use and do not recharge. During charging, the battery must be placed in a well ventilated area. 1. Charging Cradle 2. Charging Adaptor 1 2 PXCG-120U DESCRIPTION OF SYMBOLS ELECTRICAL SAFETY WARNING! When using mains-powered tools, basic safety precautions, including the following, should always be followed to reduce risk of fire, electric shock, personal injury and material damage. Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool. Save these instructions and other documents supplied with this tool for future reference. Before you connect the charger to the mains supply make sure that the data on the rating plate are identical to the mains data. This tools charger is double insulated; therefore no earth wire is required. V Volts A Amps Hz Ah Hertz Amp Hour Read instruction manual Double insulated Thermal cut out protection Indoor use only If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazard. Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool. Using an Extension Lead Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective. When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and electric shock. To reduce the risk of electric shock, we recommend the use of a residual current device (rated 30mA or less). This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. ONLINE MANUAL Scan this QR Code with your mobile device to take you to the online manual. 1. CHARGING A BATTERY CAUTION: THE CHARGER SHOULD BE PROTECTED BY A RESIDUAL CURRENT DEVICE (RATED AT 30MA OR LESS). 1 Connect the charger into a mains power outlet. 2The charger LED will flash green showing power is being supplied to the charger. 3With the battery sitting on a flat surface, align the raised ribs on the battery with the recess in the charger and slide onto the battery ensuring a firm connection. 4 The charger LED will illuminate red signifying that the battery is charging. Note: The battery will not develop a memory, it does not have to be fully discharged before recharging 5 When removing the charger from the battery, first press the battery release tab, then slide the charger from its position. Charger LED Indicator LED Indicator Situation GREEN (Flashing) Stand By (no battery pack is inserted) RED (Illuminated) Battery is charging (low charge) GREEN (Illuminated) Battery is charged and ready for use RED (Flashing) Battery or Charger fault RED & GREEN (Flashing) Battery pack is too hot or too cold (remove battery from charger and store at room temperature 20ºC. Insert battery again when at correct charging temperature). If this happens again, the battery is defective and needs to be replaced. 2. MAINTENANCE •Disconnect the charger from power source before cleaning. •Keep the charger in a dry place out of reach of children. •If the enclosure of the charger requires cleaning, do not use solvents. Use a dry, soft cloth only to wipe down the surface. Never let any liquid get inside the charger; never immerse any part of the drill into a charger. • There are no other parts inside the charger which require maintenance.Do not take the charger apart. If the charger is damaged, contact your supplier or the manufacturer. WARRANTY All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the customer service number shown. Please note the following terms under which guarantee claims can be made: 1. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you. 2. The warranty services only covers defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below are limited to either the rectification of said defects on the product or the replacement of the product, whichever we prefer. Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period. 3. The following are not covered by our guarantee: - Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance. - Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it). - Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device. 4. Your Product is guaranteed for a period of 12 months from the original date of purchase and is intended for DIY (Do It Yourself) use only. Warranty excludes consumable parts. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies if an on-site service is used. IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR REGISTER RECEIPT. Please refer to the restrictions of this warranty concerning wearing parts, consumables and missing parts as set out in the service information in these operating instructions. CUSTOMER SERVICE HELPLINE GB: 0151 294 4488 IRL: 1850 882711 Ozito-diy.co.uk OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG PXCG-120U Service information We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables. In the effect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Please ensure that you provide a precise description of the problem and answer the following questions in all cases: • • • Did the equipment work at all or was it defective from the beginning? Did you notice anything (symptom or defect) prior to the failure? What malfunction does the equipment have in your opinion (main symptom)? Describe this malfunction. Declaration of confirmity PXCG-120U ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar explains the following conformity according to EU directives and norms for the following product GB Additonal operating & safety instructions Eco Charger Eco Charger PXCG-120U (Ozito) 2014/29/EU 2005/32/EC_2009/125/EC X 2014/35/EU 2006/28/EC X 2014/30/EU 2014/32/EU 2014/53/EC 2014/68/EU 90/396/EC_2009/142/EC 89/686/EC_96/58/EC 2006/42/EC Annex IV Notified Body: Notified Body No.: Reg. No.: 2000/14/EC_2005/88/EC Annex V Annex VI Noise: measured LWA = dB (A); guaranteed LWA = dB (A) P = KW; L/Ø = cm Notified Body: 2004/26/EC Emission No.: X 2011/65/EU Standard references: EN 55014-1; EN 55014-2; EN 60335-1; EN 60335-2-29; EN 61000-3-2; EN 61000-3-3; EN 62233 Landau/Isar, den 26.04.2016 Weichselgartner/General-Manager Yang/Product-Management Archive-File/Record: NAPR014221 Documents registrar: R. Gerhard Wiesenweg 22, D-94405 Landau/Isar First CE: 16 Art.-No.: 45.120.43 I.-No.: 11016 Subject to change without notice The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the iSC GmbH. Danger! - Read the operating instructions to reduce the risk of inquiry - 135 - For use in dry rooms only. Safety class II size 445 x 210 mm Subject to technical changes Items supplied Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions. • Open the packaging and take out the equipment with care. • Remove the packaging material and any packaging and/or transportation braces (if available). • Check to see if all items are supplied. • Inspect the equipment and accessories for transport damage. • If possible, please keep the packaging until the end of the guarantee period. Danger! The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating! Proper use The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes. Technical data Charging unit: Input: ........................... 110-240V~50-60Hz, 21W Output: ...................................... 21 V DC, 800mA Charger indicator / Eco Charger Indicator status For EU countries only GREEN (Flashing) Never place any electric power tools in your household refuse. RED (Illuminated) To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot. Recycling alternative to the return request: As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any accessories or aids without electrical components supplied with the old equipment. This consignment contains lithium-ion batteries. In accordance with special provision 188 this consignment is not subject to the ADR regulations. Handle with care. Danger of ignition in case of damage to the consignment package. If the consignment package is damaged: Check and if necessary repackage. For further information contact: 0049 1807 10 20 20 66 (fixed network 14 ct/min, mobile phone max. 42 ct/min) Outside Germany charges will apply instead for a regular call to a landline number in Germany. m Important. The charging unit is allowed to be used only for the lithium-ion batteries of the Power-X-Change series! size 445 x 210 mm GREEN (Illuminated) RED (Flashing) RED & GREEN (Flashing) Explanations and actions Ready for use The charger is connected to the mains and is ready for use; there is no battery pack in the charger Charging The charger is charging the battery pack. The battery is charged and ready for use. (Charging time for 1.5 Ah battery: 2.0 h) (Charging time for 2.0 Ah battery: 2.5 h) (Charging time for 3.0 Ah battery: 4.0 h) (Charging time for 4.0 Ah battery: 5.0 h) (Charging time for 5.2 Ah battery: 6.5 h) Action: Take the battery pack out of the charger. Disconnect the charger from the mains supply. Fault Charging is no longer possible. The battery pack is defective. Action: Never charge a defective battery pack. Take the battery pack out of the charger. Temperature fault The battery pack is too hot (e.g. due to direct sunshine) or too cold (below 0° C). Action: Remove the battery pack and keep it at room temperature (approx. 20° C) for one day .
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project