- Protocol NY
Instruction Manual for
Cyrone with Gyro RC Helicopter
AGES
14+
Thank you for your purchase of Protocol's Cyrone with Gyro RC Helicopter. You are about to experience
the best of what remote control flight has to offer. We strongly recommend that you take the time to read this
manual thoroughly. It contains many tips and instructions on how to get the most of this aircraft, and maintain
it for long life.
As with any aircraft, this is a precision flying machine. Treat it well and enjoy all the fun it has to offer, flight
after flight.
Helicopter and Remote Control Parts:
Connector
A| CB Balance bar
Main rotor blades
«= ail rotor blades
—— AP Tail motor
SE Tail light
| . Vertical tail
Horizontal tail
Support pipe
Landing gear .
Charging adapter
Main rotor gears
Host rack USB adapter
Antenna
A
Camera
Indicator light К button
som] Rudder :
(Forward/backward, 1 gig memory card
Throttle left/right)
control stick
а Trim switch
= (Adjusts the balance
of helicopter)
*1 spare tail propeller and four
Spotlight switch 2 speed mode cushioned landing skids are included
ON/OFF
Assembling the Remote Control:
1. Install antenna: screw antenna into the adapter (Fig. 1)
2. Open battery case cover on the back using a small Phillips screwdriver.
3. Install batteries (6 size 1.5V AA, not included) according to polarity symbols (+) and (-) in battery compartment
(Fig. 2).
4. Replace the battery cover.
5. When the power light remains on after the remote is turned on, the batteries are working. When the power light
begins blinking, the batteries are dying and need to be replaced.
Battery Notes: Do not mix old and new batteries. Do not mix different types of batteries. Only use ‘AA’ alkaline
batteries for this product. Remove batteries if this product not going to be used for a long time. Always remove
exhausted batteries from the product and dispose of safely.
Ta)
NT LI A,
fm
+4 I
{+ I]
fe 19
| +h
f+ |<
LL —
NA LA a LA
Charging the Helicopter:
The helicopter is equipped with a high-performance Lithium-Poly battery.
1. Always turn the helicopter power switch off when charging the battery.
2. Connect the charge plug of the battery charger to the wire on the helicopter (see diagram).
3. Plug the charger into the power outlet.
4. While charging, the LED light on the charger is off.
5. When the charge is complete, the LED light brightens.
6. The battery requires 60-70 minutes of charging for
approximately 5-8 minutes of flight.
7. DO NOT CHARGE BATTERY LONGER THAN
60-70 MINUTES.
Za 3)
IMPORTANT!
Do not immerse the helicopter in water. Keep it in a cool
dry environment.
Do not use a battery charger other than the one provided.
Make sure that the battery charger power adapter fits your electrical outlet.
Never leave the helicopter battery unattended when charging.
Turn the helicopter and remote control power off when not in use.
After charging the battery, disconnect the AC adapter from the wall outlet.
2. Do not fly in strong wind. Windy conditions will limit or completely
3. Choose a flight area that is free of obstacles such as animals,
Preparing for Flight:
—
. Do not fly in temperatures below 50°F/10°C or above 113°F/45°C. Doing so may damage the helicopter and/or
adversely affect your ability to control it. -
THE
Over 8 feet
=
7
El: A. 7 oo i
interfere with flight control, resulting in your helicopter becoming >
damaged or lost. E о
es] Ver 9,
"E Cet \
; Г - JF ) A AM
people, electrical lines, trees, or other obstructions. | E Ka — A
* A A ) _
Flight Radius
Turning On The Helicopter:
1. Once the helicopter is charged, disconnect the AC charging cord from the wire of the helicopter.
2. Plug the wire into the slot on your helicopter. This closes the power circuit.
3. Turn on the helicopter.
4. Place the helicopter onto the ground and stand at least 9 feet behind it.
5. Pull the remote control antenna to its full extension.
6. Make sure the throttle on the remote control is at its lowest position.
7. Turn on the remote control. Control your helicopter as described in the following section.
*High/low speed selection:
This helicopter has high and low speed modes. Low speed is recommended for beginners and high speed is
recommended for advanced users. Just press the button on the remote control to a desired speed.
Controlling Your Helicopter:
Push up on the throttle stick (see diagram) to
Ascend
raise the helicopter.
Pull down on the throttle stick (see diagram) to =— =
Descend lower the helicopter.
Move the rudder stick (see diagram) left to turn
Steering the helicopter left.
Move the rudder stick (see diagram) right to
turn the helicopter right.
Push up the steering rudder (see diagram)
Forward and the helicopter's nose tilts down and it
flies forward.
Push down on the steering rudder (see
Backward diagram) and the helicopter's nose tilts up
and it flies backward.
*Do not crash the helicopter from a high altitude. Damage can occur to the helicopter due to its size.
Fine Tuning Your Helicopter's Flight:
If your helicopter rotates in flight even when you are not using the remote control to make it do so, then you can
adjust the trim dial to correct it.
If your helicopter is rotating left, turn the trim dial to the
right (see diagram). Continue to adjust this dial until the
helicopter flies straight.
If your helicopter is rotating right, turn the trim dial to the
left (see diagram). Continue to adjust this dial until the
helicopter flies straight.
Left turn
Note: If the helicopter is less than 1 foot from the ground, the vortex from the spinning blades can create flying
issues. Please make sure to fly the helicopter above this height.
Note: The tail blade may not always spin as you are flying. Please note that this is normal as long as you are able
to control the helicopter.
Flying Practice:
With enough practice, you can attempt the following maneuvers (see diagrams):
|
—-
CT > e —
|
= К
и San,
=
nr
Practice flying your helicopter in a rectangular pattern by
Revolving descents flying it forward and then executing a series of left-hand
turns. Gradually round off the turns so that you can fly
your helicopter in a circle.
“he -
f = \
>
Ma + — ra #
MA
Practice landings until you can land gently and Once you have mastered the above, try flying your
accurately. helicopter in a figure 8 pattern.
Using The On-Board Video Camera:
—
. Make sure the Micro SD Memory card is inserted into the slot on the
back of the helicopter. The card should go in with the copter
connecting pins facing down until you hear or feel a click (Fig. 3)
2. To make a video recording, press the ON/OFF button located on the
top right side of the transmitter (Fig. 4)
©
. The light underneath the video camera will glow green when in
stand-by mode and will flash red when recording video (Fig. 5).
4. The 1 gig memory card can record up to 20 minutes of video.
Once the card is full, the red and green lights on the bottom will
flash simultaneously.
5. To view and/or remove recordings, remove the memory card from
the rear of the camera by pushing in the card and then allowing it to
spring out enough to remove the card out of the slot.
6. Insert the memory card into slot on the back of the provided USB
adapter. If your computer features a memory card reader that fits
this memory card, then you do not need to use the USB adapter.
7. Place the USB adapter into the USB port of your computer. If you
are using Windows, the USB will come up as the “E” drive. If you
are using OS, then the USB will come up as “Untitled”.
8. Open the DCIM folder and then open the DSCIM folder to access
the .AVI file.
9. .AVI movie files can be played in several different formats including
Quicktime, Windows Media Player, and RealPlayer.
WARNING:
Never remove the Micro SD card from the video camera while the
helicopter is turned on.
NOTES:
- The video camera does not record sound.
- All files on the Micro SD card can be removed or erased without
compromising the video camera.
КБ
- Insert MicroSD card with
contacts facing down
- Push to remove
Fig.4
The remote control doesn't work:
1. Make sure the remote control's power switch is on.
2. Make sure the batteries in the remote control are inserted properly, according to polarity symbols
3. Replace the batteries.
Unable to control the helicopter:
1. Make sure the helicopter's power switch is on.
2. Make sure the helicopter’s wires are plugged into each other once the helicopter is charged.
3. Make sure the remote control’s antenna is fully extended.
4. Do not fly the helicopter in wind, which can interfere with control.
The helicopter will not ascend:
1. Make sure you are pulling up on the throttle stick.
2. Make sure the helicopter battery is fully charged.
The helicopter lands too fast/crashes:
1. Slowly pull down the throttle until the helicopter lands smoothly.
2. Make sure the helicopter battery is fully charged.
Caution:
1. Remote control range is reduced when the batteries are low.
2. When the helicopter’s battery is low, it will not fly as high.
3. Do not fly the helicopter if the rotor is damaged or broken. Injury can result.
4. Landing the helicopter too fast or crash landing will result in a shorter lifespan for the helicopter.
5. Keep hands, fingers, eyes, hair, and loose clothing away from rotors and moving parts.
Replacement Parts:
Thank you for your purchase of Protocol's Cyrone with Gyro RC Helicopter! We know that accidents can
sometimes happen which is why we offer a spare parts kit including the below available on our website
ProtocoINY.com.
Limited Waranty:
At Protocol, we're dedicated to bringing you innovative and well-designed products that make living fun and easy.
We stand behind all of our products and warrant this to be free from defects in workmanship and materials for 30
days from the date of purchase. The warranty does not cover transportation damage, misuse, crashes, accident,
or similar events. Specific legal rights pertaining to this warranty may vary by state.
For service claims or questions please consult our website ProtocoINY.com.
Troubleshooting:
(+) and (-) in the battery compartment.
Main Propeller Blade Set A (2pcs/set)
Main Propeller Set B (2pcs/set)
Tail Blade
Stabilizer/Balance Bar
Connector
PROTOCOL.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising