NHRC-M2/SC Manual for Rev B boards

NHRC-M2/SC Manual for Rev B boards
5
4
3
2
INSTALL JUMPERS TO ENABLE DESIRED SIGNALS
D
1
1
J1
5
9
4
8
3
7
2
6
1
RX_AUDIO_EXT
DOUT_EXT
TX_AUDIO_EXT
SPARE_EXT
PTT_EXT
RUS_EXT
PL_DEC_EXT
PL_ENCODE_EXT
GND_EXT
CONNECTOR DB9F
EXTERNAL CONTROLLER
1
1
1
1
1
1
1
JP16
JP15
JP14
JP13
JP12
JP11
JP10
JP9
JP1
2
JA
READ ALL NOTES BEFORE
BUILDING OR USING THIS
KIT.
TX_AUDIO_HI
2
2
2
CARD EDGE FINGERS
VOL_SQL_HI
2
2
RUS
test point A1
test point A3
test point A5
test point A7
1
2
3
4
5
6
7
8
+10V_INT
RUS_INT
PTT_INT
RX_AUDIO_INT
TX_AUDIO_INT
DOUT_INT
SPARE_INT
GND_INT
HEADER 8
ONBOARD CONTROLLER
1
1
1
1
1
1
1
NOTES:
1
JP6
JP3
JP4
JP5
JP7
JP17
A4
1
A6
1
1
2
3
4
5
6
7
RX_2_MUTE
RPTR_DISABLE
TRANSMIT_F1
RECEIVE_F1
CG_MON
PSLM
DELAYED_PTT
1
1
1
1
A14 test point
1
A12 test point
1
A10 test point
1
A8 test point
A13 test point
A11 test point
A9
test point
1
test point
1
test point
1
test point
1
B2
1
2
3
4
5
6
7
1
B4
1
B6
1
B
14
13
12
11
10
9
8
1
1
1
1
B14 test point
1
B12 test point
1
B10 test point
1
B8 test point
B13 test point
B11 test point
B9
test point
HEADER 7X2
2
+10V
2
RUS
SW1
2
2
2
VOL_SQL_HI
2
TX_AUDIO_HI
1
LOCAL_PTT
test point C1
3
REMOTE_PTT
test point C3
SW SPDT
2
test point C5
test point C7
1
test point
1
test point
1
test point
1
C2
1
2
3
4
5
6
7
1
C4
1
C6
1
Center off = PTT inhibited
2
C
14
13
12
11
10
9
8
1
VOL_SQL_HI
1
1
1
C14 test point
1
C12 test point
1
C10 test point
1
C8 test point
C13 test point
C11 test point
C9
test point
HEADER 7X2
Consult your
GE-MASTR-II station
manual for info on
Remote and Local PTT
signals,
2
C
JC
PTT SELECT/INHIBIT
Do not install J1 (DB-9) if you
intend to mount a controller to the
card.(your card wont fit) Only
install J1 if you intend to run an
external controller from this jack.
JD
test point D1
test point D3
test point D5
test point D7
1
test point
1
test point
1
test point
1
+13.8V
D2
1
D4
1
D6
1
REMOTE_PTT
TX_CG_DISABLE
+10V
1
2
3
4
5
6
7
D
SQL_ARM
LOCAL_PTT
RUS
14
13
12
11
10
9
8
1
1
1
GND
1
D14 test point
1
D12 test point
1
D10 test point
1
D8 test point
D13 test point
D11 test point
D9
test point
HEADER 7X2
B
You must install jumpers to enable
J1 or J2
Use 22 awg hookup wire
to connect the signals as desired
for your intended use.
Insert card into far right hand
"AUX CONTROL" slot J1212 for
repeater control applications.
Controller mounting holes
M11
5
M9
1
M6
1
HOLE440
Holes in a grid pattern are provided
for the customers convenience.
Cards that have been soldered are
not returnable.
B
Consult the GE MASTR-II
Station manual for signals not
listed.
The signals required for a repeater
are noted on this drawing and wired
for convenient access.
All other
signals are brought out to a test
point for user access. Consult the
GE-MASTR II Station Manual to
identify these signals.
A
A
TX_AUDIO_HI
14
13
12
11
10
9
8
JB
test point B1
2
test point B7
JP2
1
2
test point B5
JP8
A2
HEADER 7X2
Install jumpers
to complete
connections .
C
1
test point
1
test point
1
test point
1
D
2
test point B3
J2
1
HOLE440
M10
1
HOLE440
4
M7
1
HOLE440
1
HOLE440
M8
1
M4
1
HOLE440
M5
1
HOLE440
M1
1
HOLE440
3
NOTICE
HOLE440
M3
1
HOLE440
M2
1
HOLE440
THIS DRAWING CONTAINS
PROPRIETARY INFORMATION WHICH
IS THE CONFIDENTIAL PROPERTY
OF NHRC LLC. IT SHALL NOT BE
COPIED, REPRODUCED, DISCLOSED,
PUBLISHED OR USED IN PART OR
WHOLE WITHOUT THE EXPRESSED
WRITTEN PERMISSION OF NHRC LLC.
SPECIFICATIONS SUBJECT TO CHANGE
WITHOUT NOTICE OR OBLIGATION.
2
NHRC Repeater Controllers
A
415 Fourth Range Road
Pembroke, NH 03275
603-485-2248
http://www.nhrc.net
Title
NHRC-M2SC (GE MASTR II Station Card)
Size
B
Document Number
NHRC-M2SC
Date:
Wednesday, June 17, 2009
Rev
B
Sheet
1
1
of
1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising