#58199 FLOWCLEARTM

#58199 FLOWCLEARTM
#58199
220-240V~50Hz, 300W
Hmax 1.5m Hmin 0.19m IPX5
Inflate Your Fun
TM
Illustration non contractual
FLOWCLEARTM
Sand Filter
Owner’s Manual
www.bestway-service.com
D版:
英
S-S-001458
SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS - READ AND FOLLOW ALL SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
• To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
• RISK OF ELECTRIC SHOCK - The sand filter must be supplied by an isolating transformer or supplied through a residual current device (RCD) having a rated residual
operating current not exceeding 30mA.
• RISK OF ELECTRIC SHOCK - Forbid the access of the pool in case of damage of the sand filter.
• DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
• To reduce the risk of electric shock, replace damaged cord immediately.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.
• Risk of electric shock. Using the sand filter with an unmatched electrical supply is dangerous and will permanently damage the sand filter.
• Do not remove the grounding prong or modify the plug in anyway. Do not use adaptor plugs. Consult a qualified electrician for any questions relating to validity of your plugs
or grounding.
• Handle the sand filter with care. Do not pull or carry the sand filter by the power cord. Never pull a plug from the outlet by yanking the power cord. Keep cord free from
abrasions. Sharp objects, oil, moving parts, and heat should never be exposed to the sand filter.
• Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment to the product.
• This appliance is not intended for use by persons (including children) with reduced physical, sensor or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do
not play with this product.
• Electric installations should fulfill the local requirements, such as standards DIN VDE0100 part 702 for Germany. Consult a qualified electrician for
any questions.
CAUTION: This sand filter is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being readily
disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily
disassembled for storage.
NOTES:
• Place the sand filter on solid, level ground. Ensure the
PARTS REFERENCE OVERVIEW
Before assembling the sand filter, take a few minutes to become familiar with all the sand filter parts.
sand filter is at least 2 meters away from poolside.
10
REF.NO.
Keep distance as far as possible.
• Pay attention to position pool and sand filter so
adequate ventilation, drainage, and access for
maintenance is available. Never place the sand filter in
an area that may accumulate water, or on a walking
path with lots of foot traffic.
1
2
11
12
13
3
4
• It is necessary to have the plug accessible after
installation of the pool. The plug of the sand filter shall
be at least 3,5m away from the pool.
5
14
• Atmospheric conditions may affect the performance
and life span of the sand filter; take adequate
precautions to protect the sand filter from unnecessary
wear and tear that may occur during periods of cold or
hot weather and/or exposure to sun.
• It is imperative to change as soon as possible all
Control Valve
1
P6536
2
Pressure Gauge
1
P6571
3
Top Flange Clamp
2
P6553
4
Top Tank
1
P6564
5
Hub
1
P6557
6
Flange Clamp
1
P6558
7
O-ring
1
P6559
8
Drain Washer
1
P6581
9
Drain Valve Cap
1
P6580
10
Hose
2
P6610
11
Washer
5
P6029
16
12
Port D Cap
1
P6540
11
17
11
8
9
13
O-ring
1
P6149
14
Piping
1
P6560
15
Strainer Cover
1
P6561
16
Strainer
1
P6562
17
Seal Ring
1
P6563
SPECIFICATIONS
• Do not allow children or adults to lean or sit on the
apparatus.
• Do not add chemicals to the sand filter.
• When chemical products are used to clean the pool
water, it is recommended to respect a minimum
filtration time to preserve the health of swimmers
1
15
deteriorated parts. Only use parts approved by the
manufacturer.
PART NO.
7
are present before use. Notify Bestway at the
damaged or missing parts at the time of purchase.
QTY.
6
• Please examine and verify all sand filter components
customer service address listed on this manual for any
DESCRPITION
691mm
388mm
which depends on compliance of health regulation.
• This product is not intended for commercial use.
615mm
Filter Diameter:
388mm
Effective Filter Area:
0.116m2 (1.25ft2)
Max. Operating Pressure:
0.24MPa (35 PSI)
Working sand filter pressure:
< 0.045MPa (6.5PSI)
Max. Water Temperature:
35°C
Sand:
Not included
Sand Size:
#20 silica sand, 0.45-0.85mm
Sand Capacity:
Approximately 2/3 of the Tank, 25kg
PUMP DISPOSAL
Meaning of crossed-out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the
collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damage your health
and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposals at least free of charge.
2
S-S-001458
CONTROL VALVE OVERVIEW
A
WARNING: To prevent equipment damage and possible injury, always switch off sand filter before
changing the Control Valve function. Changing valve positions while the pump is running can
damage the Control Valve, which may cause personal injury or property damage.
How to Use the Control Valve
Press down on the Control Valve handle and rotate to desired function.
C
D
CONTROL VALVE FUNCTIONS
The Control valve is used to select 6 different filter functions: Filter, Rinse, Circulate, Backwash,
Closed and Drain.
Circulate: This function circulates pool water bypassing the sand filter;
use this function if the filter is broken to collect debris in the Debris
Screens.
Filter: This function is used to filter pool water and should be positioned
here 99% of the time. Water is pumped through the sand filter, where it is
cleaned and returned to the pool.
Backwash: This function is used to clean the sand bed; water is pumped
down through the Collector Hub, upwards through the sand bed, and
deposited out of Port D.
Drain: This function drains water from the pool; another filter bypass
setting, water is pumped and deposited out of Port D, instead of returning
it to the pool.
Rinse: This function for initial startup, cleaning, and sand bed leveling
after Backwash; water is pumped downwards through the sand bed, up
through the Collector Hub and deposited out of the valve Port D.
Closed: This function stops water flowing between the sand filter and the
pool.
NOTE:
•
•
•
•
•
Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
Do not set the Control Valve between two functions, or it will lead to leaking.
To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
Section I: Assembly (You will need a Phillips screwdriver.)
1. Carefully remove all components from the package and check to ensure nothing is damaged. If equipment is damaged,
immediately notify the retailer from where the equipment was purchased.
110mm
Ø8mm
2. The sand filter should be placed on solid, level ground, preferably a concrete slab. Position the sand filter so the Ports
and Control Valve are accessible for operation, servicing and winterizing.
3. EN60335-2-41 TEST standard requires the sand filter must be vertically fixed on ground or a certain pedestal made of
wood or concrete before use to prevent the sand filter from accidental falling. Fully assembled sand filter will exceed
18kg. The mounting holes should be 8mm in diameter and spaced 110mm apart. Use two bolts and nuts with a
maximum of 8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE: Use only special pool-grade filter
sand, free of all limestone or clay: #20
Silica sand 0.45-0.85mm, approximately
one 25kg bag should suffice. Use of other
sands will reduce filtering performance
and may damage the sand filter, thereby
voiding the warranty.
NOTE: To avoid damaging the Skimmer
when adding sand, pour some water into
the Bottom Tank to submerse the
Skimmer on the Collector Hub.
NOTE: SAND NOT INCLUDED. Do
not pour the sand into the pipe of the
Collector Hub.
NOTE: Make sure the O-ring on the rim
of the Top Tank is clean, and has no
nicks, tears, or scrapes or sand on it.
Sand
O-ring
Turn the nut counter clockwise to
release the flange clamp and
remove the Top Tank.
Center the Collector Hub in the
Bottom Tank. Slowly, add the sand
so the weight of the sand does not
damage the Skimmer on the
Collector Hub, until it reaches the
top rim of the Bottom Tank. Do not
pour the sand into the pipe of the
Collector Hub.
C
C
O-ring
Attach the Control Valve to the Top
Tank, ensuring the O-ring is in place
on the rim of the Top Tank and that
the vertical pipe of the Collector Hub
is inserted into the base of the
Control Valve
Nut
Nut
Connect the Pressure Gauge onto
the Control Valve.
NOTE: Make sure the O-ring on
the rim of the Top Tank is clean, dry,
and has no nicks, tears, scrapes or
sand on it.
NOTE: Before tightening, make
sure Port C on the Control Valve is
align Port C on the Pump.
Attach the Top Flange Clamp and
screw into position.
Ensure the O-ring is in place on the
rim of the Bottom Tank. Attach the
Top Tank to the Bottom Tank, place
the Flange Clamp over the seam
and turn the Nut clockwise to fasten
it
C
C
Attach the Piping to Pump Port C
and to Control Valve Port C, screw
the threaded locking rings into
position.
Make sure the Washer is properly
positioned on both ends of the
Piping.
3
S-S-001458
Section II: Hose Configuration for
Backwashing and Rinsing
D
NOTE: Ensure the Control Valve is set to the Closed function.
Your pool should be filled with water.
>1.3cm
1. Attach one Hose to the sand filter’s Port B; screw the threaded locking ring into
position.
2. Connect the other end of the Hose to Port B connection valve; screw the threaded
B
locking ring into position.
3. Open the connection valve. This allows water to flow to the sand filter.
Pool
NOTE: You can refer to pool manual for connection valve’s installation instructions.
4. Connect the other Hose to Port D and place the opposite end in drain area.
B
IMPORTANT: Ensure the Control Valve is set to the Closed function.
IMPORTANT: Make certain both of the pool’s connection valves are fully submerged
Section IV: Complete Sand Filter
Installation
by water before operating the sand filter.
Connect the Second Hose
NOTE: It is imperative to check that the hydraulic connectors are not obturated.
NOTE: Ensure the Control Valve is set to the Closed function.
1. Detach the Hose from Port D.
Section III: Backwash and Rinsing
2. Attach the Hose to the Control Valve’s Port A; screw the threaded locking ring into
Backwash and Rinsing must be preformed to prepare the pump for its first use and to
wash the sand.
CAUTION: DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device , then switch on the sand filter and run
the sand filter for 3-5 minutes, or until the water runs clear.
3. Switch off the sand filter and set the Control Valve to the Rinse function.
4. Switch on the sand filter and run the sand filter for 1 min. This circulates water
backwards through the sand filter and drains water out Port D.
5. Switch off the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT: This procedure removes water from the pool, which you’ll need to
replace. Switch off the sand filter immediately if water levels near the pool’s Inlet and
Outlet valves. DO NOT DRY RUN THE SAND FILTER.
position.
3. Connect the other end of Hose to the pool’s Inlet A.
4. Open the connection value. This allows water to flow to the sand filter.
NOTE: You can refer to pool manual for connection value’s installation instructions.
A
A
B
>1.3cm
Pool
B
Sand Filter Operation
Cleaning the Strainer
1. Now the sand filter is ready for use. Set the Control
1. Switch off the sand filter and set the Control
Valve to the Closed function.
2. Close the connection valves.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the
hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the
Strainer Cover back.
7. Open the connection valves.
NOTE: The Strainer must be emptied and
cleaned periodically. A dirty or blocked strainer will
reduce the performance of the sand filter.
Valve to the Filter function.
NOTE: To prevent the risk of electrical shock dry any
excess water from yourself and the sand filter.
2. Switch on the sand filter to run it.
NOTE: The sand filter has now started its filtering
cycle. Check that water is returning to the pool and
take note of the filter pressure on Pressure Gauge.
Generally, the recommended sand filter pressure is
less than 0.045MPa (6.5PSI) (in green area) when it is
running.
Sand Filter Maintenance
Lowering or Draining Pool Water
CAUTION: You must ensure the sand filter is
switched off and unplugged before any maintenance
begins or severe risk of injury or death exists.
Take action to avoid using pools if the filter has
problem.
Check the suction if there is any blocking.
Replace all the damaged components.
As dirt builds up in the sand filter, the pressure
reading on Pressure Gauge will increase. When the
Pressure Gauge is 0.045MPa (6.5PSI) or higher, or water flow to the pool is too low, it
is time to clean the sand.
To clean the sand bed, follow all instructions outlined previously in Section III:
Backwash and Rinsing.
NOTE: We recommend you clean the sand bed once a month or less regularly
depending on how often the pool is used. Do not clean the sand too frequently.
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and
attach to Port D.
3. Switch on the sand filter to remove pool water.
WARNING: DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized
to protect against damage. Allowing water to freeze will damage the sand filter and
void warranty.
1. Backwash the sand filter as previously outlined.
2. Drain the pool according to the pool owner’s manual.
3. Open the drain nut at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely spill the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
4
S-S-001458
TROUBLESHOOTING
Problems
Sand is flowing to the pool
Excessive filter pressure
Control Valve leaks
Connectors leaks
Probable Causes
Solutions
- Sand is too small
- Sand bed is calcified
- Recommend 0.45mm to 0.85mm #20 silica sand
- Change sand
- Dirty filter
- Calcified sand bed
- Insufficient backwashing
- Control Valve is set
between two functions
- Backwash
- Inspect sand and change if necessary
- Backwash until effluent runs clear
- Washer not in place
- Loose Hoses
- Replace the washer
- Tighten them
- Set to one function
Limited BESTWAY® Manufacturer’s Warranty 2013
The product you have purchased comes accompanied a limited warranty. Bestway stands
behind our quality guarantee and assures, through a replacement warranty, your product will
be free from manufacturer’s defects that result in leaks.
To enact a claim, this warranty card must be filled out completely and returned along with:
1) Your purchase receipt
2) Control valve (P6536) to be sent by post to the address of the after -sales centre
contacted, for details please refer to your country according to the information you find on
the back cover. Before sending the control valve, please contact your after sales center for
instructions.
Bestway is not responsible for economic loss due to water or chemical costs. With the
exception of replacement product, the results of leak are not Bestway responsibility. Bestway
will not place any products deemed to have been neglected or having been used outside of
the owner’s manual guidelines.
Select the product you have purchased:
800GAL
1000GAL
1500GAL
58199
58126NL
58257
58257GB
58199GB
58258
58256
TO: BESTWAY SERVICE DEPARTMENT
DATE
Customer Code Number
FAX/E-MAIL/TEL: Please refer to your country according to the
information you find on the back cover.
Description of problem
Water leaking
Please provide your address details in full. Note: Incomplete
Stopped working
address details will result in delayed shipments.
Item is incomplete, Which part is missing - Please
put the code you find on the instruction manual
REQUIRED INFORMATION -- PLEASE WRITE THE
Others, please describe
DELIVERY ADDRESS
Name:
Address:
For request of spare parts consumer has to send us
also the page of the manual with a cross near the
missing or faulty part.
Zipcode:
City:
Country:
All the information given need to be complete
in order to receive our assistance.
You have to send also a copy of your purchase
receipt together with this fax.
YOU CAN ALSO VISIT OUR WEB SITE:
www.bestway-service.com
Telephone:
Mobile:
E-MAIL:
Fax:
5
S-S-001458
Austria
Bestway Italy
Tel: (+43) 720 882434
Tel: (+39) 02 3626 5839
Fax: (+43) 720 882435
Fax: (+39) 02 9139 0361
E-mail: austria@bestway-service.com
E-mail: assistenza@bestway-europe.com
Belgium & Luxembourg
The Netherlands
Tel: 0 800 20 132
Tel: 08002378929
Fax: (+32) 02 6104411
Fax: (+31) 887878969
E-mail:
E-mail: dutchservice@bestway-europe.com
belgiumservice@bestway-europe.com
Norway
Tel: (+47) 22 65 01 22
Denmark
Fax: (+47) 22 72 11 27
Tel: (+45) 33 32 10 19
E-mail: norway@bestway-service.com
Fax: (+45) 33 32 10 36
E-mail: denmark@bestway-service.com
Poland
Tel: (+48) 327505320
Tel: (+358) 2 4363 600
Fax: (+48) 327505330
Fax: (+358) 2 4380 550
E-mail: serwis@bestway-service.com
E-mail: finland@bestway-service.com
Portugal
Bestway France
Telefono: 900101402
Tel: 08 92 707 709 (0.34 € TTC / Minute)
(Só a partir de linha telefónica fixa)
Fax: (+33) 04 89 069 991
: (+34) 902351045
E-mail: sav@bestway-france.com
Fax: (+34) 902451560
www.bestway-france.fr
E-mail: sac@bestwayiberica.com
Bestway Germany
Brasil
Tel: (+55) 11 5641 2193
Tel / Fax: (+55) 11 3522 7405
E-mail: sac@bestway-brazil.com
Chile
Tel: (+56) 2 365 0315
E-mail: info@bestway-southamerica.com
Mexico
Tel: (+52) 81 8346 3416
Fax: (+52) 81 8346 6581
E-mail: mexico@bestway-southamerica.com
Perú
Tel: (+51) 1 254 1119
E-mail: peru@bestway-southamerica.com
Spain
Tel: (+49) 069 4600 1281
Telefono: (+34) 902351045
Fax: (+49) 069 4600 1282
E-mail: kundendienst@bestway-europe.com
Tel: 00 800 391 275 300
Bestway Central & South America Ltda
Salar de Ascotan 1282, Parque Enea,
Pudahuel, Santiago, Chile
Tel: (+56) 2 365 0315
Fax: (+56) 2 365 0323
E-mail: info@bestway-southamerica.com
Tel: (+48) 322326040
Finland
Greece
United Kingdom
Tel: 0800 612 0457
Fax: (+44) 1626 835736
E-mail: aftersales@bestway-uk.com
www.bestway-uk.com
Fax: (+34) 902602705
E-mail: sac@bestwayiberica.com
Sweden
Tel: (+46) 8 506 691 90
Fax: (+39) 02 9139 0361
Fax: (+46) 506 690 99
E-mail: aftersales@bestway-europe.com
E-mail: sweden@bestway-service.com
Hungary
Switzerland
Tel: (+36) 06 40 204 624
Tel: (+41) 071 929 00 00
Fax: (+36) 23 382 406
Fax: (+41) 071 929 00 90
Email: hungary@bestway-service.com
E-mail: switzerland@bestway-service.com
Bestway Inflatables & Material Corp.
No.3065 Cao An Road, Shanghai, 201812,
China.
Tel: (+86) 21 6913 5588
Fax: (+86) 21 5913 8383
E-mail: info@bestway-shanghai.com
Bestway (Europe) s.r.l.
Via Resistenza 5,
20098 San Giuliano M.se (Mi) - Italy
Tel: (+39) 02 3626 5839
Fax: (+39) 02 9139 0361
E-mail: aftersales@bestway-europe.com
www.bestway-service.com
www.bestway-service.com
D版:
英
S-S-001458
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising