2-4409 Radiance NV.indd - Log in - Fire

2-4409 Radiance NV.indd - Log in - Fire
INSTALLER / CONSUMER
SAFETY INFORMATION
PLEASE READ THIS MANUAL
BEFORE INSTALLING AND
USING APPLIANCE.
WARNING!
IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING
PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS OF
LIFE.
Radiance Natural Vent
Gas Heater
Model RNVOD: 3233 thru 3236,
3340 thru 3349, 3355, 3356
— Do not store or use gasoline
or other flammable vapors and
liquids in the vicinity of this or
any other appliance.
— WHAT TO DO IF YOU SMELL
GAS:
• Do not try to light any appliance.
• Do not touch any electric switch; do
fire-parts.com
•
•
not use any phone in your building.
Immediately call your gas supplier
from your neighbor’s phone. Follow
the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
This appliance may be installed in
an after market permanently located
manufactured (mobile) home where not
prohibited by local codes.
This appliance is only for use with the
type of gas indicated on the rating plate.
4409 Installation
Homeowner’s
Radiance
and Operating
Manual
cover
4/01
DE S I GN
C E RT I F I E D
CE
RTIFI E D
This appliance is not convertible for use
with other gases unless a certified kit is
used.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
20004409 4/07 Rev. 17
Radiance Natural Vent Gas Heater
Table of Contents
PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE.
Thank you and congratulations on your purchase of a Vermont Castings stove.
IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these
instructions may result in a possible fire hazard and will void the warranty.
Installation & Operating Instructions .......................................................................................... 3
Stove Dimensions ............................................................................................................... 4
Clearance Requirements..................................................................................................... 4
Parallel Installation .............................................................................................................. 4
Corner Installation ............................................................................................................... 5
Ceiling Clearances .............................................................................................................. 5
Alcove Minimum Dimensions .............................................................................................. 5
Mantel Clearances .............................................................................................................. 5
Hearth Requirements .......................................................................................................... 5
Gas Specifications............................................................................................................... 6
Gas Inlet and Manifold Pressures ....................................................................................... 6
High Elevations ................................................................................................................... 6
Venting Requirements ......................................................................................................... 6
Vent Layout and Height Requirements................................................................................ 7
Passing Through a Combustible Wall or Ceiling ................................................................. 7
Assembly Procedures
Tools Required .................................................................................................................... 8
Parts Bag Contents ............................................................................................................. 8
Unpack and Assembly Legs ................................................................................................ 8
Install Optional Fan ............................................................................................................. 8
Venting System Assembly ................................................................................................. 12
Connect Gas Supply Line.................................................................................................. 13
Burner Information............................................................................................................. 13
Install ON/OFF Switch ....................................................................................................... 13
Thermostat Connection (Optional) .................................................................................... 14
Install the Mesh and Grille ................................................................................................. 14
Install Rear Bracket and Log Set....................................................................................... 14
Operation
Operable Doors ................................................................................................................. 16
Your First Fire .................................................................................................................... 16
Pilot and Burner Information.............................................................................................. 16
Flame & Temperature Adjustment ..................................................................................... 16
Flame Characteristics........................................................................................................ 16
Lighting and Operating Instructions................................................................................... 16
Troubleshooting - Honeywell #8420 Gas Control System ................................................. 16
Fuel Conversion Instructions ............................................................................................. 19
Maintenance
Annual System Inspection ................................................................................................. 22
Logset and Burner/Cleaning and Inspection ..................................................................... 22
Care of Cast Iron ............................................................................................................... 22
Cleaning the Glass ............................................................................................................ 22
Glass Replacement ........................................................................................................... 22
Gasket Replacement ......................................................................................................... 23
Inspect the Vent System Annually ..................................................................................... 23
Check the Gas Flame Regularly ....................................................................................... 23
Wiring Diagrams ................................................................................................................ 24
Replacement Parts ...................................................................................................................... 25
Optional Accessories .................................................................................................................. 28
Warranty ....................................................................................................................................... 30
Energuide ....................................................................................................................................... 32
fire-parts.com
2
20004409
Radiance Natural Vent Gas Heater
Installation & Operating Instructions
The Radiance Direct Natural Vent Room Heater, Model Nos.
3233 thru 3236, 3340 thru 3349, 3355 and 3356 are vented
gas appliances listed to the ANSI standard Z21.88-2005 and
CSA-2.33-2005 for Vented Room Heaters, and CSA 2.17-M91,
Gas-Fired Appliances For Use at High Altitudes.
The installation of the Radiance Natural Vent Room Heater
must conform with local codes, or in the absence of local codes,
with National Fuel Gas Code, ANSI Z223.1/NFPA 54 — latest
edition and CSA B-149.1 Installation Code. (EXCEPTION: Do
not derate this appliance for altitude. Maintain the manifold
pressure at 3.5 inches w.c. for Natural Gas and 10 inches w.c.
for LP gas at maximum input.)
This appliance is only for use with the type of gas indicated on
the rating plate. This appliance is not convertible for use with
other gases unless a certified kit is used.
Installation and replacement of gas piping, gas utilization
equipment or accessories, and repair and servicing of
equipment shall be performed only by a qualified agency,
preferably NFI or WETT (Canada) certified. The term “qualified agency” means any individual, firm, corporation, or
company that either in person or through a representative
is engaged in and is responsible for (a) installation or
replacement of gas piping, or (b), the connection, installation, repair, or servicing of equipment, who is experienced
in such work, familiar with all precautions required, and
has complied with all the requirements of the authority
having jurisdiction.
The Radiance Natural Vent Room Heater should be inspected before use and at least annually by a qualified
service agency. It is imperative that control compartments,
burners, and circulating air passageways of the appliance
be kept clean.
The Radiance Natural Vent Room Heater and its individual
shut-off valve must be disconnected from the gas supply piping
during any pressure testing of that system at test pressures in
excess of 1/2 psig (3.5 kPa).
The Radiance Natural Vent Room Heater must be isolated from
the gas supply piping system by closing its individual manual
shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig.
An accessible tap is located above the pilot/On-Off knob for
checking the inlet pressure.
This appliance mmust be properly connected to a listed 4”
(102 mm) Type B venting system or toan approved masonry
or factory-built chimney system. In Canada, a complete reline
of Class A chimneys is required. This heater is equipped with
a vent safety shutoff system.
This appliance is approved for bedroom installations in the
U.S. and Canada. Check local codes for natural vent requirements.
This appliance may be installed in an aftermarket* manufactured (mobile) home, where not prohibited by state or local
codes.
WARNING: Operation of this heater when not connected
to a properly installed and maintained venting system can
result in carbon monoxide (CO) poisoning and possible
death.
The Radiance Natural Vent Room Heater, when installed, must
be electrically grounded in accordance with local codes or, in
the absence of local codes, with the National Electrical Code
ANSI/NFPA 70, (latest edition), or of the current Canadian
Electrical Code C22.1.
Due to high temperatures this appliance should be located
out of traffic and away from furniture and draperies.
WARNING: This appliance is hot while in operation. Keep
children, clothing, and furniture away. Contact may cause
burns or ignition of combustible materials.
Children and adults should be alerted to the hazards
of high surface temperatures and should stay away to
avoid burns or clothing ignition. Young children should
be carefully supervised when they are in the same room
as the appliance.
Clothing or other flammable materials should not be placed
on or near the appliance.
Any safety screen, glass or guard removed for servicing
an appliance must be replaced prior to operating the appliance.
The appliance area must be kept clear and free from combustible materials, gasoline, and other flammable vapors
and liquids.
The flow of combustion and ventilation air must not be
obstructed. The installation must include adequate accessibility and clearance for servicing and proper operation.
WARNING: Do not operate the Room Heater with the
glass panel removed, cracked or broken. Replacement
of the panel should be done by a licensed or qualified
service person.
Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
Do not burn wood, trash or any other material for which this
appliance was not designed. This appliance is designed
to burn either natural gas or propane only.
This gas appliance must not be connected to a chimney
flue serving a separate solid-fuel burning appliance.
CAUTION: Label all wires prior to disconnection when
servicing controls. Wiring errors can cause improper and
dangerous operation.
Verify proper operation after servicing.
fire-parts.com
20004409
* Aftermarket: Completion of sale, nor for purpose of resale,
from the manufacturer.
Proposition 65 Warning: Fuels used in gas, woodburning or
oil fired appliances, and the products of combustion of such
fuels, contain chemicals known to the State of California to
cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6
3
Radiance Natural Vent Gas Heater
Stove Dimensions
4" Inner Dia.
(102 mm)
14���"
(378 mm)
CL
Refer to Page 5 for Flue
Collar Centerline Dimensions
4���"
(114 mm)
29���"
(756 mm)
RADIANCE
28"
(711 mm)
fire-parts.com
Supply
Inlet
5"
(127 mm)
9���"
(241 mm)
31"
(787 mm)
18���"
(464 mm)
Fig. 1 Radiance dimensions.
Parallel Installation:
Minimum Clearance and Flue Centerline
Clearance Requirements
Minimum Clearances to
Combustible Materials
4409
Radiance natural Vent
specs
25/31/01 djt
Measure side clearances as shown in Figures
through 5 from the outer edge of the cast iron stove
top. Measure rear clearances from the rear sheet metal
shroud.
C
D
C
L
A
C
L
The Radiance heater is approved for installation into
an alcove constructed of combustible materials to the
dimensions and clearances shown on this page.
The same clearances apply in a standard parallel
installation.
B
Stove Clearance:
ST128b
4
A: 4” (102 mm)
B: 6” (152 mm)
Pipe Centerline:
C: 21⁷⁄₈” (556 mm)
ST128b
D: 8¹⁄₂” (216 mm)
RNV flue centerline
Fig. 2 Parallel installation, minimum
back and side clear5/11/00 djt
ances and flue centerlines.
20004409
Radiance Natural Vent Gas Heater
Corner Installation:
Minimum Clearance and Flue Centerline
Alcove Minimum Dimensions
B
42"
(1067 mm)
4"
(102 mm)
A
B
6"
(152 mm)
A
ST129b
Fig. 3 Corner installation requirements.
6"
(152 mm)
ST130a
Fig. 5 The Radiance ST130a
Natural Vent Stove is approved for
installation into alcoves built of combustible materials.
RNV
alcove specs
5/11/00
djt
A
Ceiling Clearances
ST129b
RNV corner specs
5/11/00
B
fire-parts.com
C
46"
(1168mm)
V
D
W
74"
(1880mm)
E
X
Wall
Y
Z
RADIANCE
ST694
ST131b
Fig. 4 Minimum ceiling clearance: minimum alcove height.
ST131b
RNV ceiling clearance
5/11/00 djt
Ref.
A
B
C
D
E
Mantel
Shelf Depth
7¹⁄₂” (190 mm)
6”
(152 mm)
4¹⁄₂” (114 mm)
3”
(75 mm)
1¹⁄₂” (38 mm)
Ref.
V
W
X
Y
Z
Mantel from
Stove Top
16” (406 mm)
14¹⁄₂” (368 mm)
13” (330 mm)
11¹⁄₂” (292 mm)
10” (254 mm)
Fig. 5a Minimum mantel clearance.
FP599b
Hearth
JUV Requirements
stove mantel heights
The Radiance Heater
must
9/21/00
djtbe installed on rigid flooring.
When the heater is installed directly on any combustible
surface other than wood flooring, a metal or wood panel
extending the full width and depth of the unit must be
used as the hearth. There are no other hearth requirements.
20004409
5
Radiance Natural Vent Gas Heater
Warning:
•
•
• Always maintain required clearances
(air spaces) to nearby combustibles to
prevent fire hazard. Do not fill air spaces with
insulation. All venting components must maintain
a 1” (25 mm) clearance to combustible materials.
Maintain a 6” (150 mm) clearance when using
single wall pipe.
The gas appliance and vent system must be
vented directly to the outside of the building and
never be attached to a chimney serving a separate solid fuel or gas-burning appliance.
Refer to the manufacturer’s instructions included
with the venting system for complete installation
procedures.
Gas Specifications
Model
RNVODRN
RNVODRP
Fuel Gas Control
Nat.
Millivolt
Prop.
Millivolt
Max.
Min.
Input
Input
BTU/h BTU/h
35,000 25,000
35,000 27,000
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury or property damage. Refer to this manual for
correct installation and operational procedures.
For assistance or additional information consult
a qualified installer, service agency, or the gas
supplier.
Venting Requirements and Options
The Radiance must be properly connected to a listed
4” (102 mm) Type B venting system or to an approved
Class A masonry or factory-built chimney system. In
Canada, a complete relining of Class A chimney systems is required.
The Radiance Natural Vent stove will accept decorative 6” (150 mm) stove pipe around the Type B venting
system, for aesthetic purposes.
Complete Type B vent systems are available from a
number of manufacturers, and your dealer can usually
supply one. Pipe sections from different makers are not
interchangeable; do not mix pipe or vent sections from
different makers. Follow the vent system manufacturer’s
instructions exactly.
fire-parts.com
Gas Inlet and Manifold Pressures
Inlet Minimum
Inlet Maximum
Manifold Pressure
Natural
5.5” w.c.
14.0” w.c.
3.5” w.c.
LP (Propane)
11.0” w.c.
14.0” w.c.
10.0” w.c.
Radiance Direct Vent / Natural Vent
Certified to:
ANSI Z21.88-2005 / CSA Z2.33-2005
Vented Gas Fireplace Heaters
The installation must conform with local codes or, in
the absence of local codes, with the National Fuel
Gas Code, ANSI Z223.1/NFPA 54 - latest edition.
(EXCEPTION: Do not derate this appliance for altitude. Maintain the manifold pressure at 3.5” w.c. for
Natural Gas and 10” w.c. for Propane.)
High Elevations
Decorative stove chimneys for B vent applications are
available through vent dealers.
The vent system should conform to specifications of the
National Fuel Gas Code, latest edition.
If connecting to a Class A chimney system, use 4” (102
mm) single wall or 4” Type B vent connector. Single wall
vent connector requires a minimum 6” (153 mm) clearance to combustible surfaces.
Exterior chimneys may be subject to flow reversal or
condensation. To lessen these conditions, enclose Type
B vents in an insulated chase, or reline exterior Class A
chimneys.
An approved pass-through device is always required,
whether the vent system passes through a wall or
a ceiling. Use a pass-through device from the same
maker who supplies the venting system.
Venting terminals shall not be recessed into a wall or
siding.
Input ratings are shown in BTU per hour and are
certified without deration for elevations up to
4,500 feet (1,370 m) above sea level.
For elevations above 4,500 feet (1,370 m) in USA,
installations must be in accordance with the
current ANSI Z223.1/NFPA 54 and/or local codes
having jurisdiction.
In Canada, please consult provincial and/or local
authorities having jurisdiction for installations at
elevations above 4,500 feet (1,370 m).
6
20004409
Radiance Natural Vent Gas Heater
Vent Layout and Height Requirements
The minimum vent system height for the Radiance
Natural Vent Stove is 8 feet (2.43 m), (Fig. 7) measured
from the top of the stove. To determine the minimum
height the vent system must extend through or past the
roof, refer to the 1993 edition of the National Fuel Gas
Code.
Passing Through a
Combustible Wall or Ceiling
An approved pass-through device is always required
when a vent passes through a combustible wall or ceiling. Check with the maker of the vent system for the
correct listed devices that are available. A listed passthrough device is required whether or not the installation includes decorative pipe around the Type B venting
system. NOTE: It is essential to seal between the ceiling support (sometimes called a ‘firestop spacer’) and
the decorative pipe, if installed, with a high-temperature
silicone sealant. (Fig. 6)
36
Vertical Run (in feet)
(Measured from top of the unit before any elbow)
Venting for a Radiance can rise vertically through the
home, or can pass through an exterior wall and rise
along the outside of the home. Some codes require that
a Type B vent system rising on the outside of the home
be enclosed in a chase. Check your local codes for
requirements.
34
A
32
30
B
28
26
24
22
20
18
16
14
12
10
8
6
4
2
1 2 4
6 8 10 12 14 16 18 20 22 24
Horizontal Run (in feet)
fire-parts.com
Complete the venting system installation according to
the manufacturer’s instructions.
Air
Space as
Required
by Code
Joists
Ceiling
Support
High-temperature
Silicone
Sealant
Trim Collar
High-temperature
Silicone
Sealant
Decorative 6”
Pipe
Listed 4” (102
mm) B-Vent
Air Space
ST361
Venting Runs
NOTE: When venting staight vertical, without an
elbow, a minimum of 8 ft. vertical is required
off the top of the stove.
= Acceptable venting configuration
= Unacceptable venting configuration
A: Vertical installations up to 36 feet (12m) in
height. Up to an 18 ft. horizontal vent run can be
installed within the vent system using a
maximum of two 90-degree elbows or four
45-degree elbows.
B: Vertical installations up to 36 feet (12m) in
height. Up to a 24 ft. horizontal vent run can be
installed within the vent system using a
maximum of two 45-degree elbows.
(Ratio = 2/3, Hor./Vert.)
FP567b
Fig. 7 Vent termination window.
FP567
NVBR/NVBC VENTING RUNS
11/12/97
Fig. 6 A ceiling pass-through, with decorative pipe around the
ST361
vent.
Ceiling pass thru
5/11/00 djt
20004409
7
Radiance Natural Vent Gas Heater
Assembly Procedures
Tools Required
• Phillips screwdriver (stub)
• power drill
• utility knife
• reciprocating saw
• metal drill bit: size 28 (.140”/3.5 mm)
CAUTION: To prevent valve tubing from being
crushed or damaged, make sure to rest valve on
wooden pallet.
Unpack and Set Up the Stove
The Radiance is shipped on its back. Cut the shipping
straps and set stove upright.
Parts Bag Contents:
• On-Off switch, housing, and wiring harness
• 2 Bags of Lava Rock
• 7 Screws
• Pipe Support Bracket
• Fan Bracket*
• Door Handle (Operable)
• Control Door Handle
• Owner Registration Card
• (4) CS, Hex Hd 3/8-16 x 1 GR 2-Z
• (4) Washer, FL 3/8-Z
*Used with stove’s having serials #’s starting at #1457
(RNVODRN), #1944 (RNVODRP).
Washer
Hex Head Bolt
ST721
Fig. 9 Carefully tip stove onto back legs. Leave pallet under
stove to keep stove from falling fully forward.
fire-parts.com
Unpack and Assemble Legs
The Radiance is shipped upright. Cut the shipping
straps and set stove upright.
1. Slide stove to the rear of the pallet just far enough to
access rear leg holes. Make sure the stove does not
tip over backwards. (Fig. 8)
ST721
4. Have your assistant attach one leg using the hardRadiance
ware described.
attach
5. Move the pallet to allow access to the other front leg
front
hole. Attach remaining
leg.legs
7/30/02
6. Remove pallet and allow stove djt
to gently rest on all
four legs.
7. Adjust leg levelers to compensate for irregularities in
the hearth.
WARNING
This appliance is equipped with a three-prong
(grounded) plug for your protection against
shock hazard and should be plugged directly into
a properly grounded three-prong receptacle. Do
not cut or remove the grounding prong from this
plug.
ST720
Fig. 8 Slide stove back just far enough to access rear leg
holes.
2. Attach the rear legs using 3/8” hex head bolts and
flat washer supplied.
Tighten with a 9/16” wrench or
ST720
socket.
Radiance
3. Carefully tip the stove
its rear
legs. Adjust the
slideonto
stove
back
pallet to allow access to one of the front leg holes.
7/30/02 djt
Be sure to leave the pallet under the stove to prevent
the stove from falling fully forward. (Fig. 9)
8
Install the Optional Fan
These instructions are for stoves with serial numbers up
to #1456 (RNVODRN), #1943 (RNVODRP).
If you are installing the optional convection Fan Kit
#2767 (FK26), continue here. It is easiest to install fan
kit before connecting gas line. If you are not installing a
Fan Kit, proceed to Venting System Assembly.
20004409
Radiance Natural Vent Gas Heater
1. The fan kit includes a Blower Assembly and a Rheostat Assembly, connected by a cable. (Fig. 10) The
Blower Assembly mounts to the bottom rear of the
stove, and the Rheostat mounts to the left side of
the valve. The assembly includes a ‘snapstat’ which
automatically turns the fan On (or Off) above (or
below) approximately 109˚F. The Rheostat also provides a range of fan speed settings from Off (which
overrides the snapstat function) to High. Unpack and
inspect the Blower assembly. Confirm that the fan
spins freely.
Snapstat
Assembly
• Remove retaining nut from shaft of rheostat. (if
preinstalled)
• Insert the rheostat through the hole in the back
•
•
•
of the left side of the valve bracket, aligning the
locator pin with the smaller hole in that bracket.
Thread the retaining nut onto the shaft of the
rheostat, tightening with a wrench. Do not overtighten.
Attach the control knob to the rheostat shaft.
Use the wire tie to secure the fan and rheostat
wire harnesses together.
Not Used
on
Radiance
1/4”-20 x
1/2” Hex
Bolts
Rheostat
Assembly
Star
Washer
Snapstat
Housing
Snapstat
Bracket
Slot
fire-parts.com
ST146
Fig. 10 Fan kit components.
Fan Shield
Edge ‘A’
ST369
Fig. 12 Position fan behind rear shroud.
2. Remove the rear shroud. (Fig. 11) Use work gloves
to protect your hands. Remove the rear shroud
cover plate. Remove the six sheet metal screws (‘A’,
ST146
Fig. 9) surrounding
FK26 the draft hood opening. Remove
kit parts
the shroud and 2767
set fan
it aside.
10/99
Rear Shroud
A
Rear Shroud
Cover Plate
(Shipping Position)
ST363
Fig. 11 Remove/replace rear shroud.
3. PositionST363
the fan behind the rear shroud. (Fig. 12)
Switch
Housing assembly and snapstat asPass the
fan rheostat
5/00
sembly beneath the stove toward the front.
4. The rheostat control switch attaches to the left side
of the valve bracket at the front of the stove. (Fig.
14)
20004409
Hex Nuts
5. Attach the snapstat housing to the snapstat bracket
with two sheet metal screws and one #8 star washer.
(Fig. 12)
ST369
6. Attach the snapstat
bracket, with the snapstat asRNV
sembly attached rheostat
to it, to the&horizontal surface on
the inside of the rear shroud. Use a sheet metal
snapstat assy
screw. There are predrilled holes at each corner of
djtpart of the snapstat
the panel for this.5/19/00
The vertical
bracket should be 3/16” back from Edge ‘A’. (Fig. 12)
7. Attach the fan assembly to the rear shroud using two
1/4”-20 x 1/2” hex head bolts, two 1/4” -20 nuts and
one 1/4” star washer. (Fig. 12)
8. Reattach the stove’s rear shroud.
9. Reattach the rear shroud cover plate by fastening
it to the rear shroud as shown in Figure 13. The top
edge of the cover plate goes inside the rear shroud.
Reinstall and tighten the six sheet metal screws
around the draft hood opening; see ‘A’, Figure 13.
Use two screws from the fan kit to fasten the rear
shroud to the fan shield; refer to ‘A’, Figure 13.
Plug the fan cord into a standard grounded 110 volt
household outlet.
9
Radiance Natural Vent Gas Heater
Rear Shroud
Cover Plate
A
Rear Shroud
Assembly
ST713
A
ST371
Fig. 13 Attach rear shroud cover plate to the rear shroud.
Rheostat
Retaining Collar
Rheostat Knob
Fig. 15 Remove rear shroud.
5. Attach the fan assembly to the fan bracket provided
in the finish bag. Use the #10 sheet metal screws
provided with fan kit. Do not remove finger guard
screws. (Fig. 16)
ST372
Attach rear
skirt cover
Rheostat
5/19/00 djt
ST713fan
remove shroud
Snapstat
radiance
Wire
Rheostat
11/99
Wire
fire-parts.com
Fan
Bracket
ST347a
Fig. 14 Attach the fan rheostat.
ST347a
Install theJUV
Optional Fan
FK28
These instructions are for stoves with serial numbers
rheostat install
starting at #1457 (RNVODRN), #1944 (RNVODRP).
9/21/00
If you are installing the optional convection Fan Kit
#2767 (FK26), continue here. It is easiest to install fan
kit before connecting gas line. If you are not installing a
Fan Kit, proceed to Venting System Assembly.
1. The fan kit includes a Blower Assembly and a Rheostat Assembly, connected by a cable. The Blower
Assembly mounts to the bottom rear of the stove,
and the Rheostat mounts to the left side of the valve.
The assembly includes a ‘snapstat’ which automatically turns the fan On (or Off) above (or below)
approximately 109˚. The Rheostat also provides a
range of fan speed settings from Off (which overrides the snapstat function) to High. Unpack and
inspect the Blower assembly. Confirm that the fan
spins freely.
2. Loosen the four phillips head screws which secure
the rear shroud to the stove sides. (Fig. 15)
3. Carefully pull the shroud assembly away from the
rear of the stove.
4. With the rear shroud assembly in the upright position, set the bottom of the shroud on a padded
surface to prevent scratching the surface. Unfasten
the four phillips head screws which attach the outer
shroud to the inner duct assembly.
10
ST669
Finger Guard
Fig. 16 Attach the fan assembly to the fan bracket.
6. Connect snapstat leads. Disconnect the snapstat
module from the leads inside the snapstat bracket.
ST669the snapstat bracket. Use
(Fig. 17) Bend open
RUVSOD
needle nose pliers
tofan
remove
the black plastic gromattach
to bracket
met from the bracket.
Discard the bracket. Insert the
7/01
grommet and wires into the large hole at the bottom
right corner of the inner shroud. Feed the snapstat
wire leads through the grommet into the stove interior. Connect the two wires to the two snapstat extension leads attached to the inner shroud or, on some
models, in between the inner and outer shroud.
7. Position the fan assembly so the ducts slide between
the inner and outer shroud. The inner shroud should
engage with the two slots in the ends of the bracket
so that bracket and shroud are interlocked. (Fig. 18)
Secure the bracket with the four sheet metal screws
provided in the finish bag.
20004409
Radiance Natural Vent Gas Heater
Snapstat Bracket
Snapstat Module
Pinch
Grommet to
Remove
11. Slide shroud assembly over the sides and fasten the
four screws loosened earlier.
12. The rheostat control switch attaches to the left side
of the valve bracket at the front of the stove. (Fig. 20)
• Remove retaining nut from shaft of rheostat. (if
preinstalled)
• Insert the rheostat through the hole in the back
•
ST670
Fig. 17 Remove the snapstat and grommet from the bracket
and insert the grommet into the inner shroud.
Outer
Shroud
•
•
of the left side of the valve bracket, aligning the
locator pin with the smaller hole in that bracket.
Thread the retaining nut onto the shaft of the
rheostat, tightening with a wrench. Do not overtighten.
Attach the control knob to the rheostat shaft.
Use the wire tie to secure the fan and rheostat
wire harnesses together.
ST640
RUVSOD
Slot
snapstat
7/01
Inner Shroud
Rheostat
Slot
fire-parts.com
Retaining Nut
Control Knob
ST347a
Fig. 20 Attach rheostat to left side of valve.
Left Air Duct
Snapstat
MOTOR
BLK
BLK
8. Route the rheostat wire
assembly to the right
ST194
attach
fan toshroud.
shroud
between the inner and
outer
Run the wire
11/99
through the slots at the bottom right corner of the
inner shroud. Some models have the extension wire
assembly attached to the inner shroud.
9. Refasten the outer shroud to the inner duct assembly.
10. Install the snapstat by loosening the front screw on
the inner side of the duct (Fig. 19) slide the snapstat
under the head of the screw and tighten. Connect
the leads to the snapstat. Make sure the snapstat
assembly is mounted straight front to back.
BLK
SNAPSTAT
WHT
BLK
WHT
Fig. 18 Position the fan to engage the inner shroud with the
fan bracket slots and secure with sheet metal screws.
ON/OFF
RHEOSTAT
GRN
ST194
ST347a
13. Plug the power cord into
a standard grounded 110
JUV
volt household outlet. IfFK28
the fan control knob is not
turned to the OFF position,
the fan
will turn on when
rheostat
install
the temperature at the 9/21/00
snapstat reaches approximately 109°F.
POWER
ST196
Fig. 21 #2767 / FK26 Fan wiring diagram.
ST671
Fig. 19 Install the snapstat and connect the extension wire
terminals. View is with top removed, however, access is
available through the rear when installing fan before gas line
connection.
20004409
ST196
FK26 fan diangram
11/99
11
Radiance Natural Vent Gas Heater
Venting System Assembly
Adjust the leg levelers as needed. They should not
extend any further from the leg than necessary.
The venting collar is on the sheet metal draft hood/heat
exchanger assembly, over the firebox. Use a B-vent
adapter, from the same maker as the rest of the B-vent
components, to join the first section of venting to the
draft hood.
The RNVOD stove includes a vent safety switch.
Operating this stove when not connected to a properly
installed and maintained venting system, or tampering
with or disconnecting the vent safety switch can result
in carbon monoxide (CO) poisoning and possible death.
Attach the first section of venting to the B-vent adapter.
Depending on the length of the individual venting
sections and the lengths of the decorative pipe, you
may need to slip the decorative pipe over the venting
sections before attaching upper sections to lower ones.
The sections of decorative pipe should be oriented with
their seams (if any) toward the wall; sections usually
do not need to be fastened at each joint, other than slip
sections. The decorative pipe need not be fastened to
the locating bracket on the stove. If the layout includes
a slip section, this should be the last section of pipe visible in the room at the ceiling. Refer to Page 7, Figure 6,
for details on joining the decorative pipe at the ceiling.
The stove includes a bracket for installing decorative 6
inch (150mm) round stove pipe around the B-vent, for
appearance purposes only. The decorative pipe need
not be concentric with the vent pipe.
If the installation includes decorative stove pipe around
the venting system, make a cardboard template of the
decorative pipe by tracing its circumference. Put this
template in the flue recess in the stove top. Position the
template to fit well against the front of the recess. (Fig.
22) Use this template to locate the bracket to hold the
decorative pipe Depending on spacing, the bracket may
fit inside the decorative pipe without interfering with the
vent system. Fasten the bracket to the draft hood/heat
exchanger assembly with a sheet metal screw.
fire-parts.com
Template
Sheet Metal
Screws
Bracket
ST373
Fig. 23 Attach the B-vent adapter to the flue.
B-vent Pipe
Decorative Pipe
7FSSK
ST373
attach
Bracket
b vent adapter
5/19/00 djt
ST374
Fig. 24 Install decorative pipe over the B-vent pipe.
ST372
Fig. 20 Use a template to locate the bracket for decorative
pipe to surround the B-vent pipe.
Insert the B-vent adapter into the flue collar and drill
ST372
1/8” (3mm) pilot holes through
both the stove’s collar
and the adapter. Attach theattach
adapter to the flue collar
with sheet metal screws. (Fig.
21)
decorator
pipe
ST374
attach
decorative pipe
5/19/00 djt
bracket
5/19/00 djt
12
20004409
Radiance Natural Vent Gas Heater
Burner Information
Connect the Gas Supply Line
Check the Rating Plate attached by a steel cable to the
firebox, to confirm that you have the appropriate firebox
for the type of fuel to be used. The Radiance may be
converted from one gas to another using the appropriate Fuel Conversion Kit listed on Page 26.
The appliance must only use the gas specified on the
rating plate, unless converted using a Fuel Conversion
Kit. To convert from LP to Natural Gas use Kit #0005009. To convert from Natural Gas to LP use Kit #0005010.
CAUTION
Conversion instructions are provided with each kit and
beginning on Page 19 in this manual.
This appliance should only be connected
by a qualified gas technician. Test to
confirm manifold pressures as specified
below.
The Radiance Heater and its individual shutoff
valve must be disconnected from the gas supply
piping during any pressure testing of that system
at test pressures in excess of 1/2 psig (3.5 kPa).
The Radiance Heater must be isolated from the
gas supply piping system by closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test
pressure equal to or less than 1/2 psig.
THIS APPLIANCE SHOULD BE CONNECTED TO
THE GAS SUPPLY ONLY BY A QUALIFIED GAS
SERVICE TECHNICIAN. FOLLOW ALL LOCAL
CODES.
THERE MUST BE A GAS SHUT-OFF BETWEEN
THE STOVE AND THE SUPPLY.
In order to connect Natural Gas, use a fitting with a
3/8” NPT nipple on the valve side and 1/2” natural gas
supply line with an input of 35,000 BTUs at a manifold
pressure of 3.5” and minimum inlet supply pressure of
5.5” w.c.
In order to connect Propane, use a fitting with a 3/8”
NPT nipple on the valve side and 1/2” propane gas
supply line with an input of 35,000 BTUs at a manifold
pressure of 10.0” and minimum inlet supply pressure of
11.0” w.c.
fire-parts.com
There must be a gas shutoff between the stove
and the supply.
In order to connect Natural Gas, use a fitting with
a 3/8” NPT nipple on the valve side and 1/2” natural gas supply line with an input of 35,000 BTUs at
a manifold pressure of 3.5” and a minimum inlet
supply pressure of 5.5” w.c.
In order to connect Propane, use a fitting with
1/2” NPT on the valve side and 1/2” propane gas
supply line with an input of 35,000 BTUs at a
manifold pressure of 10.0” and a minimum inlet
supply pressure of 11.0” w.c.
In the U.S.; Gas connection should be made in accordance with current National Fuel Gas Code, ANSI
Z223.1/NFPA 54. Since some municipalities have additional local codes, be sure to consult you local authority.
Install ON/OFF Switch
The switch assembly parts are found in the parts bag.
1. Attach switch assembly to left rear side of stove
shroud (when facing shroud) using two screws and
existing holes in shroud. (Fig. 25)
2. Run wires down back of stove, under bottom of rear
shroud to valve.
3. Attach wires to valve terminals. (Fig. 26)
Switch Assembly
Existing Holes
In Canada; consult the local authority and CSA-B149.1
installation code.
Connect the gas supply and test for leaks. Use a 50/50
solution of liquid soap and water to test for leaks at gas
fittings and joints. Apply water/soap solution with brush
only - do not over apply. NEVER test with an open
flame. Light the pilot according to the directions on
page 16, before going to the next step.
Screws
ST315
Fig. 25 Attach switch assembly to rear shroud.
20004409
13
Radiance Natural Vent Gas Heater
PILOT
ADJ
Install Rear Bracket and Log Set
TPTH
1. Remove the logs from their packaging, and inspect
each piece for damage. DO NOT INSTALL DAMAGED LOGS.
TP
Rear Log
Bracket
TH
ST228
Fig. 26 Attach switch wires to valve.
Thermostat Connection (optional)
Use only a thermostat rated for 500 - 750 millivolts.
Check the table belowST228
for the appropriate gauge thermostat wire to use for attach
the length
of lead required in your
switch
installation.
wires to valve
12/99
Thermostat
Wire / Gauge
Maximum Run
18
40 feet
20
25 feet
22
16 feet
1. Install the wall thermostat in the desired location and
run the wires to the stove location. Terminate these
leads with 1/4” female connectors.
2. Connect the thermostat wires to the valve. (Fig. 26)
LG158
Fig. 27 Radiance firebox and rear log bracket.
2. Install the left rear log by placing it on the rear log
bracket at the back of the firebox. (Fig. 28) The left
LG156
rear log should
touch the back wall of the firebox.
Radiance
logs
Slide the left rear
log to the
left until the left side lines
up with the left
bracket. djt
(Fig. 28) When the left rear
4/23/01
log is in place the front left corner of the log should
rest on the decorative grate.
3. Install the right rear log by placing it on the rear log
bracket at the back toward the right. Make sure the
right side of the right rear log lines up with the right
bracket. (Fig. 29) NOTE: When the right and left rear
logs are in place, they should touch the back of the
firebox and each other.
4. Install the right log by engaging hole on the bottom
left of the right log with pin on the front left of the
right rear log. (Fig. 29) Set the bottom right of the
right log on the bracket and bring the bottom right
forward to come in contact with decorative grate on
the right.
5. Loosely sprinkle the lava rocks directly on top of the
burner just behind decorative grate. Use the lava
rock to cover brackets on the burner. Do not place
lava rocks toward back of burner. The lava rock is
shipped inside the finish bag assembly. (Figs. 29,
30)
fire-parts.com
Install the Mesh and Grille
Place the mesh and grille on the top of the Radiance
stove to complete assembly.
14
20004409
Radiance Natural Vent Gas Heater
Figure 28
Right Log
Right Rear Log
Left Rear Log
Figure 29
LG156
Decorative
Grate
Left Bracket
Right Bracket
fire-parts.com
LG156
Radiance logs
4/23/01 djt
LG155
Log rests on
decorative grate
Figure 30
Left Rear
Log
Right Rear
Log
Lava Rock
LG155
Radiance logs
installed
4/24/01 djt
LG160
Decorative Grate
NOTE: Right log is not shown in this view.
20004409
LG160
RNV logs
top view
6/4/01 djt
Lava rock may
be placed in this
area
15
Radiance Natural Vent Gas Heater
Operation
Operable Doors
The Radiance is shipped with the operable door front.
The stove may be operated with the doors either open
or closed. To open the front doors, insert the handle into
the door latch stub and turn it to the right and up. (Fig.
31) When not in use, the handle may be stored in the
handle holder on the right side of the rear shroud. (Fig.
32)
Pilot Assembly
ST476
Fig. 33 Pilot assembly location.
Turn
counterclockwise
to decrease
flame height
Clockwise to Close
Turn clockwise
ST477HI
to increase
Stardance
pilot location flame height
HV102
10/4/00
LO
Counterclockwise
to Open
Fig. 34 Flame adjustment knob for Honeywell valve.
ST621a
Fig. 31 To open the front doors, turn handle
counterclockwise.
Flame Characteristics
It is important to periodically perform a visual check of
the pilot and burner flames. Compare them to Figures
HV102 appear abnormal con35 and 36. If the flame patterns
Honeywell
knob and adjusttact a qualified service provider
forhi/lo
service
4/5/99
djt
ment.
fire-parts.com
Handle Holder
RADIANCE
ST656
ST621
Fig. 30 When
not in use, store handle in the handle holder.
Radiance
Your
First Fire
operable
doors
Read these 1/31/01
instructions carefully and familiarize
yourself with the burner controls shown on Page 16.
Locate the pilot assembly, Figure 33. Follow the lighting
instructions on Page 17 exactly.
During the first fire, it is not unusual to smell some
odor associated with new logs, paint and metal being
heated. Odors should dissipate within an hour or so,
however, you can open a window to provide fresh air to
alleviate the condition.
CO105c
Fig. 35 Correct pilot flame pattern. SIT pilot.
Pilot andST624
Burner Inspection
handle holder
2/6/01
Each time you light your heater check that the pilot
flame and burner flame patterns are as shown in Figures 35 and 36. If flame patterns are incorrect, turn the
heater off. Contact your dealer or a qualified gas technician for assistance. Do not operate the heater until the
pilot flame is correct.
Flame & Temperature Adjustment
For units equipped with HI/LO valves, the flame adjustment is accomplished by rotating the HI/LO knob located near the center of the gas control valve. (Fig. 34)
CO105c
Pilot flame
4/10/00 djt
Red Glow
LG157
Fig. 36 Correct burner flame pattern.
20004409
16
LG157
Radiance Natural Vent Gas Heater
Lighting and Operating Instructions
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING:If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This heater has a pilot which must be lit manually. When lighting the pilot follow these instructions exactly.
B. BEFORE LIGHTING smell all around the heater
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any fireplace
• Do not touch any electric switch
• Do not use any phone in your building
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
•
If you cannot reach your gas supplier, call the
Fire Department
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it, call a
qualified service technician. Applying force or any
attempted repair may result in a fire or explosion.
D. Do not use this fireplace if any part has been under
water. Immediately call a qualified service technician to inspect the heater and to replace any part of
the control system and any gas control which has
been under water.
Lighting Instructions
1. STOP! Read the safety information above.
2. Turn off all electrical power to the fireplace.
3. For MN/MP/TN/TP appliances ONLY, go on to
Step 4. For RN/RP appliances turn the On/Off
switch to “OFF” position or set thermostat to
lowest level.
4. Open control access panel.
5. Push in gas control knob slightly and turn
clockwise
to “OFF”.
10. Push the control knob all the way in and hold.
Immediately light the pilot by repeatedly depressing the piezo spark ignitor until a flame appears.
Continue to hold the control knob in for about one
(1) minute after the pilot is lit. Release knob and it
will pop back up. Pilot should remain lit. If it goes
out, repeat steps 5 through 8.
fire-parts.com
ON
OFF
OFF
3 4 5
Euro SIT
T
LO
PI
ON
1 2
P
OFF ilot
PILOT
3/8" - 1/2"
OFF
SIT NOVA
Honeywell
6. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you
smell gas, STOP! Follow “B” in the safety inforFP1067
mation above. If you
do
not smell gas, go to the
lighting
instruction
next step.
knobs
3/9/01
djt
7. Remove glass door
before
lighting pilot. (See
Glass Frame Removal section).
8. Visibly locate pilot by the main burner.
9. Turn knob on gas control counterclockwise
to “PILOT”.
•
If knob does not pop up when released, stop
and immediately call your service technician or
gas supplier.
FP1068
•
If after several tries,
the pilot will not stay lit,
Lighting
instructions
turn the gas control knob
to “OFF”
and call your
Pilots
service technician or gas supplier.
11. Replace glass door.
12. Turn gas control knob to “ON” position.
13. For RN/RP appliances turn the On/Off switch to
“ON” position or set thermostat to desired setting.
14. Turn on all electrical power to the fireplace.
To Turn Off Gas To Heater
1. Turn the On/Off switch to Off position or set the
thermostat to lowest setting.
2. Turn off all electric power to the fireplace if
service is to be performed.
20004409
3. Open control access panel.
4. Push in gas control knob slightly and turn clockwise
to “OFF”. Do not force.
5. Close control access panel.
17
Radiance Natural Vent Gas Heater
Troubleshooting / Honeywell #8420 Gas Control System
NOTE: Before troubleshooting the gas control system, be sure the external gas shutoff is in the “ON” position.
WARNING: REMOVE THE GLASS PANEL BEFORE PERFORMING ANY GAS CONTROL SERVICE WORK.
SYMPTOM
1. Spark ignitor will
not light
2. Pilot will not stay lit
after carefully following the lighting
instructions
POSSIBLE CAUSES
CORRECTIVE ACTION
A. Defective or misaligned
electrode at the pilot
Using a match, light pilot. If pilot lights, turn off pilot and
push the ignitor button again. If pilot will not light, check
gap at electrode and pilot - it should be 1/8” to have a
strong spark.
B. Defective ignitor (push button)
Push piezo ignitor button. Check for spark at electrode
and pilot. If there is no spark at the pilot, and electrode
wire is properly connected, replace ignitor.
A. Defective pilot generator
(thermocouple)
Check pilot flame. It must impinge on the thermocouple
or thermopile. NOTE: This pilot burner assembly uses
both a thermocouple and a thermopile. The thermocouple operates the pilot flame. Tighten the thermocouple.
The thermopile operates the main valve (ON and OFF).
Clean and/or adjust pilot for maximum flame impingement on thermocouple and thermopile.
B. Defective automatic valve
operator
Turn valve knob to ‘Pilot’. Maintain flow to pilot; millivolt
meter should read greater than 10mV. If the reading
is okay and the pilot does not stay on, replace the gas
valve. NOTE: An interrupter block (not supplied) must be
used to conduct this test.
fire-parts.com
3. Pilot lights, no gas
to burner, valve
knob ON, remote
switch (rocker
switch) ON
A. Remote switch or wires
defective
Check rocker switch and wires for proper connection.
Use jumper wires across terminals at rocker switch. If
burner lights, replace rocker switch. If okay, use jumper
wires across rocker switch wires at the valve; if burner
lights, wires are faulty or connections are bad.
B. Thermopile may not generate sufficient voltage
1. Be sure wire connections from thermopile at gas valve
terminals are tight and thermopile is fully inserted into
pilot bracket.
2. One of the rocker switch wires may be grounded.
Remove rocker switch wires from valve terminals. If
burner now stays lit, trace rocker switch wiring from
ground. It may be grounded to the appliance or the
gas supply line.
3. Check the thermopile with a millivolt meter. Take reading at thermopile (“TP” and “TP/TH”) terminals of gas
valve. Should read 325 millivolts minimum while holding valve knob depressed in PILOT position and with
rocker switch OFF. Replace faulty thermopile if reading
is below specified minimum.
4. Frequent pilot outage
18
C. Plugged burner orifice
Check burner orifices for debris, and remove.
D. Defective automatic valve
operator
Turn knob to ON, place rocker switch to ON, millivolt meter should read greater than 10 mV. If the reading is okay
and the burner does not light, replace the valve.
A. Pilot flame may be too low
or high, (blowing or lifting),
causing the pilot to drop out
B. Possible blockage of the
vent terminal
Clean and/or adjust pilot flame for maximum flame impingement on thermocouple and thermopile.
Check the vent terminal for blockage.
20004409
Radiance Natural Vent Gas Heater
Fuel Conversion Instructions
WARNING! This conversion kit shall be installed
by a qualified service agency in accordance with
the manufacturer’s instructions and all applicable
codes and requirements of the authority having
jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion
or production of carbon monoxide may result
causing property damage, personal injury or loss
of life. The qualified service agency is responsible for the proper installation of this kit. The
installation is not proper and complete until the
operation of the converted appliance is checked
as specified in the manufacturer’s instructions
supplied with the kit.
CAUTION: The gas supply shall be shut off prior
to disconnecting the electrical power, before proceeding with the conversion.
6. Remove the right and left log bracket assembly by
unfastening the two screws which hold the burner in
place. (Fig. 38)
Remove Screws
Rear Log Bracket
Pilot
Left & Right Log
Bracket Assembly
ST350
Fig. 38 Attach the gas line to the left side of the valve.
Burner Orifice Conversion
1. Hold the burner at the right hand side and lift to clear
ST350
the right burner leg.
Then pull to the right to clear the
injectors on the left
hand side.
Jefferson
2. Remove injector orifices
from left
air shutter
adjburner leg using
1/2” wrench. (Fig. 3/20/00
39)
djt
3. Install conversion orifices. (Refer to Table 1)
O H
PILOT
ADJ
ON
L
I
PI
LO
T
fire-parts.com
OFF
Gas Supply Inlet
Main Gas
LIne
ST226a
Left Burner Leg
Fig. 37 Attach the gas line to the left side of the valve.
Injector Orifices
Conversion Precautions
This conversion must only
be completed by qualified
ST226
personnel. Before proceeding,
attach gasturn
line control knob on
djt OFF. Turn OFF any
valve to OFF and turn 12/8/99
gas supply
electricity that may be going to the appliance.
CAUTION: Allow stove to cool completely before beginning conversion.
Conversion Procedure
1. Remove stove front. Lift stove front up and then
swing bottom out and away to disengage from the
stove body. (Page 22, Fig. 44)
2. Undo the right and left latches at the top of the glass
frame. (Page 22, Fig. 45)
3. Pull the top edge of the glass and frame assembly
away from the firebox face. Place the assembly out
of the way on a flat, padded surface such as a counter protected by a towel.
4. Remove the logset from the firebox.
5. Remove the rear log bracket by unfastening the
screw and pulling the bracket away. (Fig. 38)
90°
ST353a
Fig. 39 Remove and replace injector orifices.
Valve Conversion
Honeywell Valve
1. Remove cap from Hi-Lo knob. This can be accomplished by lifting the plastic cap off the screw. (Fig.
40)
ST353a
Cap
HI
injector orifice
replace
Lift Open
3/21/00 djt
LO
HI
LO
Hi-Lo Knob
Center Screw
CO100
CO100
Gas conversion
Fig. 40 Remove center screw from
HI/LO knob.
HI-LO knob
3/15/99 djt
20004409
19
Radiance Natural Vent Gas Heater
2. Remove the screw from center of Hi-Lo knob with
small screwdriver turning counterclockwise. (Fig. 40)
3. Insert blue painted screw when converting to natural
gas and red painted screw when converting to LP.
4. Tighten screw (do not over tighten), replace cap.
SIT 820 Valve
1. Using TORX T20 bit, remove and discard the three
(3) pressure regulator mounting screws (A), pressure
regulator tower (B) and the spring and diaphragm
assembly (C). (Fig. 41)
2. Insure the rubber gasket (D) is properly positioned
and install the new HI/LO pressure regulator assembly to the valve using the new screws (E) supplied
with the kit. Tighten the screws securely. (Ref. torque
= 25 in/lb) (Fig. 42)
3. Install the enclosed conversion label (F) to the valve
body where it can easily be seen. (Fig. 42)
A
Pilot Orifice Conversion
1. Locate pilot. (Fig. 38)
2. Replace pilot orifice.
• Remove pilot hood by lifting up. (Fig. 43) NOTE: It
is not necessary to remove the pilot tube for conversion.
• Remove pilot orifice with allen wrench. (Fig. 44)
• Install the conversion orifice.
• Reinstall pilot hood. Be sure to align hood with
index tab.
Pilot Hood
Pilot
Bracket
CO105a
B
Fig. 43 Remove pilot hood.
fire-parts.com
Index Tab
C
OF
FP
Snap Ring
Allen Wrench
IL
CO105a
gas conversion
Pilot
1/28/00 djt
OT
O
CO106a
Fig. 44 Remove pilot orifice.
FC107
Fig. 41 Remove mounting screws, pressure regulator tower
and spring and diaphragm assembly.
E
FC107
SIT820
valve conversion
10/03
3. Air shutter adjustment. The unit is shipped from the
CO106a
factory with the air shutter
open 1”. For LP units only,
DV360/580
the air shutter could be
closed
further. Refer to Table
Gas Conversion
3 for minimum air shutter
Pilot2opening. The air shutter is
djt
located on the bottom1/28/00
of the burner
to the left. (Fig.
45)
Refer to Table 2
Bottom of Burner
Pan
IL
FP
OF
OT
O
D
F
FC108
Fig. 42 Replace regulator.
20
FC108
SIT
regulator
conversion
10/03
ST667
Fig. 45 Adjust air shutter on bottom of heater. Refer to Table
2 for correct position.
ST667
RNVOD
air shutter 20004409
converting
from NG to Lp
Radiance Natural Vent Gas Heater
4. Replace burner. Slide the burner in at an angle
with left side lower than the right side. Slide the left
side onto the injectors, making sure the burner leg
remains at a 90° angle to the base. Lower the right
hand side down in to place. Make sure the burner is
as far left as possible and the injector shoulders are
inside the burner.
NOTE: It is very critical to keep the left burner leg,
which holds the injectors, at a 90° angle to the base.
(Fig. 39) This keeps the orifices aligned with the
tubes inside burner. Failure to do so could affect the
flame appearance and performance of the unit.
5. Place conversion label on valve.
6. Reinstall the right and left log bracket assembly.
7. Reinstall the rear log bracket.
8. Replace logs.
9. Replace glass and stove front.
Conversion is complete.
Table 2 Injector Orifice Size Matrix
fire-parts.com
Kit #
000-5009
Front
#51 / .067”
Conversion to Natural Gas
Part #
Rear
Part #
30000449 #40 / .098” 20004263
Input (BTU/h)
Minimum
Maximum
25,000
35,000
Kit #
000-5010
Front
#57 / .043”
Conversion to LP
Part #
Rear
Part #
20004587 #54 / .055” 20000130
Input (BTU/h)
Minimum
Maximum
27,500
35,000
Table 3 Air Shutter Adjustment
Model
RNVOD
20004409
Natural Gas
1¹⁄₂”
LP
Fully closed
21
Radiance Natural Vent Gas Heater
Maintenance
Your Radiance Gas Heater will provide years of service
with minimal upkeep. The following procedures will help
ensure that your stove continues to function properly.
Annual System Inspection
Have the entire heater and venting system inspected
annually by a qualified gas technician. Replace any
worn or broken parts.
Logset and Burner
Cleaning and Inspection
Cleanliness is critical to the proper function of the
heater. The logset and burner must all be kept free of
dust and unobstructed by debris. Inspect these areas
before each use and clean as necessary.
1. Turn the burner OFF and let the heater cool completely before cleaning.
2. Lift the Stove Front up and then swing the bottom
out to disengage it from the heater shell. (Fig. 46)
3. Carefully remove the glass and frame assembly and
place it out of the way on a flat, padded surface such
as a counter protected by a towel.
4. Carefully inspect the Logs for damage. Contact your
local dealer if any damage is evident.
5. Use a soft bristled brush to sweep dust or debris
from the Logs, Pilot and Burner. Use care as the
logs are fragile and susceptible to damage.
6. Replace the glass panel and frame assembly.
7. Replace the Stove Front.
CAUTION
TURN THE PILOT OFF BEFORE PAINTING.
ALLOW THE HEATER TO COOL COMPLETELY
BEFORE PAINTING
Cleaning the Glass
WARNING: Let the glass cool completely before attempting to clean.
It will be necessary to clean the glass periodically. During start-up, condensation, which is normal, forms on
the inside of the glass and causes lint, dust and other
airborne particles cling to the glass surface. Also initial
paint curing may deposit a slight film on the glass. It is
therefore recommended that the glass be cleaned two
or three times with a non-ammonia household cleaner
and warm water (we recommend gas fireplace glass
cleaner). After that the glass should be cleaned two or
three times during each heating season depending on
the circumstances present.
fire-parts.com
Clean glass after first two weeks of operation.
Glass Replacement
Replace glass only with CFM Corporation approved
parts. Refer to Page 25 for Replacement Parts. Refer to
Figure 47 for removal of the damaged glass frame.
Care of Cast Iron
An occasional dusting with a dry rag will help keep the
painted surfaces looking new. Use high-temperature
stove paints, available through your local dealer, to
touch-up areas as needed. Clean areas to be painted
with a wire brush and be sure to cover the logs, burner
and valve assembly, glass and frame assembly. Apply
the paint sparingly; two light coats of paint will give better results than a single heavy coat.
Clean porcelain enamel surfaces with a soft, damp
cloth. Do not use abrasive cleaning agents. If necessary, use only a cleaning agent formulated especially
for use on porcelain enamel surfaces.
ST139
Fig. 46 Remove stove front.
22
ST139
Radiance
remove front
4/20/01 djt
20004409
Radiance Natural Vent Gas Heater
ST179
ST141
Fig. 47 Release the latches to remove the glass frame.
Gasket Replacement
ST141
The Radiance Gas Heater uses
a ‘tadpole’
type gasket
pull glass
latch
to seal between the glass panel
10/99 and the frame. In time,
this gasket can become brittle and compressed and
should be replaced. New gasket is available from your
dealer.
Fig. 48 Wrap the gasket material around the outside edge of
the glass.
ST179
Inspect theglass
Vent gasket
Systemdetail
Annually
11/99
Have the vent system inspected annually by a qualified
technician. Shut off the main gas supply before inspecting the system. Both the inner exhaust pipe and the outer combustion supply pipe must be checked to confirm
that they are unblocked and in good condition.
fire-parts.com
Shut off the gas supply and allow the stove to cool.
Wear safety goggles and a dust mask.
1. Remove the Front, Glass Frame and Glass Panel.
(Figs. 46 & 47) Remove the old gasket. Use a razor
blade, with rounded corners, to separate the glass
and gasket from the frame, and to clean the glass of
any remaining cement or bits of gasket.
2. Determine the correct length of gasket by laying it
out around the edge of the glass. Allow an extra 1
- 2” (25-50mm). Mark the spot to be cut. Use a utility
knife.
3. Starting on a long edge, remove about 6” of the protective paper strip and apply the flat adhesive face
of the gasket around the outside-facing edge of the
panel. Continue around the panel, applying about 6”
at a time being careful not to stretch the material. Do
not overlap the gasket ends. (Fig. 48)
4. Apply a thin bead of high temperature silicone
rubber sealant along the inside corner of the glass
frame, all around the perimeter. Place the flat
gasketed side of the glass panel back into the steel
frame. Pinch the rounded inside-facing gasket material to bulk it up.
5. Replace the glass frame and front panel as previously described.
20004409
Check the Gas Flame Regularly
To ensure that the stove is operating properly, check the
flames periodically to confirm that they match Figure 49.
The flames will be blue during the first 15-20 minutes of
operation, and will gradually turn to yellow after that.
Do not use your stove if the flame pattern differs from
that shown here. Contact your Vermont Castings dealer
or a qualified technician for help.
Red Glow
LG157
Fig. 49 Correct flame pattern.
LG157
Radiance logs
flame
4/24/01 djt
23
Radiance Natural Vent Gas Heater
OFF
On/Off Switch
Wiring
ON
Thermopile
Black
TP/TH
Black
TH
K
GRN
BL
Thermostat
(Optional)
Optional Thermostat
Wiring
Black
Chassis
Ground
ST124b
Thermostat
(Optional)
BLK
WHT
BL
TP
Millivolt
Gas Valve
K
BLK
FAN JUNCTION BOX
St124b
on/off/switch
wiring
1/11/00 djt
Thermopile
TP/TH
FAN
POWER
CORD
Strain Relief
fire-parts.com
TP
ON / OFF
Rheostat
Black
TH
ST124c
Snapstat
Fig. 50 On/Off switch and optional thermostat circuit.
LK
WHT
Thermostat
wiring
1/11/00 djt
BLK
B
NOTE: IF ANY OF THE ORIGINAL WIRE, AS
SUPPLIED WITH THE APPLIANCE, MUST BE
REPLACED, IT MUST BE REPLACED WITH TYPE
St124c
SF-2, 200°C WIRE OR ITS EQUIVALENT.
GRN
Chassis Ground
RHEOSTAT / SNAPSTAT
BOX
ST153
Safety Limit
Switch
Schematic Diagram
BLK
Thermocouple
BLK
MOTOR
ST153 BLK
rdv connections diag.
10/99
WHT
BLK
ST665
GRN
WHT
Valve
SNAPSTAT
ON/OFF
RHEOSTAT
Fig. 51 Safety Limit Switch
ST665 wiring.
Safety Limit
Switch wiring
5/29/01 djt
ST236
Fig. 52 Stardance fan circuit.
ST236
FK26 wiring diagram
12/99
24
20004409
Radiance Natural Vent Gas Heater
6
4
1a
7
2
1b
15a,b
3
1c
9a,b
10
11
12
8a,b,c,d
16
7a,b
LO
5
T OFF
O H
PILOT
ADJ
ON
L
I
PI
13
18a,b
17
14
20
19
27
fire-parts.com
22
23
28
26a,b,
c,d
35
21
29
25
24
34
39
40
31
32
36
33a
30
33b
38
42
41
37
43
44a,b
45
CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time,
without notice.
Radiance Natural Vent Gas Heater (RNVOD)
3456
Stardance parts
10/5/00 djt
Models: 3233 thru 3236, 3340 thru 3349, 3355, 3356
20004409
25
Radiance Natural Vent Gas Heater
Radiance Natural Vent Gas Heater (RNVOD)
Models: 3233 thru 3236, 3340 thru 3349, 3355, 3356 (continued)
Ref.
1.
1a.
1b.
1c.
2.
3.
4.
5.
6.
7a.
7b.
8a.
8b.
8c.
8d.
9a.
9b.
Description
Log Set -RDVOD/RNVOD
Right Rear Log RDNOD/RNVOD
Left Rear Log RDVOD/RNVOD
Right Log RDVOD/RNVOD
Manifold Assembly
Lava Rock - Burner
Frame, Glass RDV40
Glass, Gasket Med. Knit - RDV40
Glass, GFP Firebox
Valve RN Honeywell VS8420E 2038 (Serial #’s up to 2512)*
Valve RP Honeywell VS8420E 2020 (Serial #’s up to 2512)**
Pilot Assembly 3/BVent RN 0.199.705
Pilot Assembly 3/BVent RP 0.199.704
Pilot Assembly 3Way N/DV RN 0.199.706 Serial #’s starting at #1457 (RNVODRN)
Pilot Assembly 3Way N/DV RP 0.199.703 Serial #’s starting at #1944 (RNVODRP)
Thermocouple Serial #’s up to #1456 (RNVODRN), #1943 (RNVODRP)
Thermocouple 24” Serial #’s starting at #1457 (RNVODRN), 1944 (RNVODRP)
RNVOD
20004184
20004185
20004186
20004187
20003739
57897
1409112
1203702
1601290
10001782
10001759
10002389
10002390
10002264
10002265
54912
53373
7531137
10001297
10002266
51827
7533113
57886
10001296
10002268
10002269
20003526
20003536
51866
fire-parts.com
10.
11.
12.
13.
14.
15a.
15b.
16.
17.
18a.
18b.
19.
20.
21.
22.
23.
24.
25.
26a.
26b.
26c.
26d.
27.
28.
29.
26
Electrode Ignitor w/cable SIT 24
Pilot Top Convertible
Thermopile 18” RS
Nut Electrode SIT #0.974.144
Tubing Pilot w/ Fitting 1/8 x 24”
Orifice Pilot #62 NG Top Convertible
Orifice Pilot #35 - LP Top Convertible
Burner Housing Assembly
Burner Decorative Grate
Switch, Vent Safety
Serial #’s up to #1456 (RNVODRN), #1943 (RNVODRP)
Switch, Spill - RNVOD
Serial #’s starting at #1457 (RNVODRN) #1944 (RNVODRP)
Wiring Harness - FSDV32RN/JDV
Switch, ON/OFF JDV
Front II RDVOD
Door, Left, RDVOD
Door, Right, RDVOD
Control Door, RDVOD
Handle Package, Ceramic w/SCR
Orifice Hood, #57 Front - LP
Orifice Hood, #51 Front - NG
Orifice Hood, #54 Rear - LP
Orifice Hood, #40 Rear - NG
Bracket, Right Log
Bracket, Left Log
Base Pan Inner Gasket
20005039
10002582
30000874
Refer to Enamel Parts Chart Page 27
Refer to Enamel Parts Chart Page 27
Refer to Enamel Parts Chart Page 27
Refer to Enamel Parts Chart Page 27
0004345
20004587
30000449
20000130
20004263
20005259
20005258
20004286
20004409
Radiance Natural Vent Gas Heater
Radiance Natural Vent Gas Heater (RNVOD)
Models: 3233 thru 3236, 3340 thru 3349, 3355, 3356 (continued)
Ref.
30.
31.
32.
33a.
33b.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44a.
44b.
45.
46.
Description
RNVOD
Bracket, Back Log - RDVOD
20003577
Grille, RVF
1301192
Screen, RVF
1601933
Vent Switch Wire Assembly - RNV40
Serial #’s up to #1456 (RNVODRN), #1943 (RNVODRP)
30000108
Spill Switch Wire Assembly - RNVOD
Serial #’s starting at #1457 (RNVODRN), #1944 (RNVODRP)
30000108
Damper Steel Handle/Screw
30002720
Latch, Front DR - RDV
30001249
Control Door Handle Assy
30002730
Interrupter Block Serial #’s starting at #1457 (RNVODRN), #1944 (RNVODRP)
30000069
Draft Hood Final Assembly Serial #’s starting at #1457 (RNVODRN), #1944 (RNVODRP)
20005118
Left End
Refer to Enamel Parts Chart Page 27
Right End
Refer to Enamel Parts Chart Page 27
Leg
Refer to Enamel Parts Chart Page 27
Top
Refer to Enamel Parts Chart Page 27
Inner Shroud Grommet
20005860
Valve Nova SIT820.662 RN (Serial #’s starting with 2513)
20010563
Valve Nova SIT820.653 RP (Serial #’s starting with 2513)
20010645
Ignitor Piezo w/Nut SIT
52464
Bracket Piezo Ignitor (not shown)
20010876
fire-parts.com
*When converting to SIT valve, must order RP275
**When converting to SIT valve, must order RP269
Fuel Conversion Kits
Conversion Kit, NG to LP - RDVOD/RNVOD NG
Conversion Kit, LP to NG - RDVOD/RNVODRP
Kit #000-5010
Kit #000-5009
Shell Enamel Part Numbers
Model
Number
3340, 3345
3233
3341, 3346
3234
3235
3344, 3349
3343, 3348
3342, 3347
3355, 3356
3236
20004409
Color
Classic
Biscuit
Bordeaux
Chestnut
Brown
Ebony
Forest
Green
Midnight
Blue
Sand
Suede
Brown
Vermont
Cl. Green
Top
1301235
30003274
2321235
30003275
Left
End
30001751
30003239
30001771
30003248
Right
End
30001752
30003238
30001770
30003247
30003276
2311235
30003257
30001780
2371235
Front
30001376
30003240
30001416
30003249
Left
Door
30001378
30003242
30001418
30003251
Right
Door
30001377
30003241
30001417
30003250
Control
Door
30001413
30003243
30001419
30003252
Leg
(4)
30001753
30003245
30001772
30003254
30003256
30001779
30003258
30001428
30003260
30001430
30003259
30001429
30003261
30001431
30003263
30001781
30001777
30001776
30001424
30001426
30001425
30001427
30001778
1321235
30002513
30001774
30002512
30001773
30002511
30001420
30002514
30001422
30002516
30001421
30002515
30001423
30002517
30001775
30002518
30003277
30003266
30003265
30003267
30003269
30003268
30003270
30003272
27
Radiance Natural Vent Gas Heater
Optional Accessories
Fan Kits
FK26 Fan
The FK26 fan kit helps distribute heated air from within
the firebox out into the room. The fan is controlled by a
snapstat that turns power on and off as the firebox temperature rises above and falls below a preset temperature. A rheostat provides for variable fan speeds.
Specifications
115 Volt / 60Hz / .75 amps
Maintenance
The fan itself does not require regular maintenance,
however, periodic cleaning of the fan and the surrounding area is required.
Installation
Refer to Page 8 for installation instructions.
Remote Controls
Screen Kit
An optional screen, R40SK, is available for use with the
operable doors to allow the doors to be left in the open
position.
Warming Shelf
Warming shelves add versatility to your stove; they can
be used to keep foods warm at mealtime.
Model
Color
1560
Classic Black
1555
Biscuit
1556
Chestnut Brown
1557
Ebony
1558
Vt. Classic Green
1565
Bordeaux
1562
Sand
1566
Forest Green
1567
Midnight Blue
1568
Suede Brown
fire-parts.com
The remote control allows you to turn the heater on or
off from anywhere in the room. Refer to Page 23 for
wiring diagrams.
Model
Functions Controlled
RC1
ON/OFF
RC2
ON/OFF and Temperature
IMTFK
Wall mounted thermostat control
The shelf installation is accomplished in three stages.
First attach the shelf loosely to the stove, leaving the
screws loose enough to allow final adjustments. Then,
position the shelf and adjust the brackets so the shelf
fits correctly. Finally, tighten the screws.
Refer to the instructions included with each warming
shelf for complete installation procedures.
Decorative Rings
7” brass or charcoal gray rings are available to add a
decorative touch to the exposed stove pipe.
Model
4FSDRP/4
4FSDRB/4
Description
4” Polished Brass Rings (4)
4” Black Rings (4)
Outside Air Adapter
An outside air adpater, #5076, may be added to the
stove to bring fresh air directly from outside the building
into the stove.
28
20004409
Radiance Natural Vent Gas Heater
fire-parts.com
20004409
29
Radiance Natural Vent Gas Heater
LIMITED LIFETIME WARRANTY
PRODUCT COVERED BY THIS WARRANTY
All Vermont Castings gas stoves, gas inserts, and gas fireplaces, and all Majestic brand gas fireplaces equipped with
an Insta-Flame Ceramic Burner, or standard steel tube burner.
BASIC WARRANTY
CFM Corporation (hereinafter referred to collectively as the Company) warrants that your new Vermont Castings or Majestic Gas
Fireplace/Stove is free from manufacturing and material defects
for a period of one year from the date of purchase, subject to the
following conditions and limitations.
EXTENDED LIFETIME WARRANTY
The heat exchanger, where applicable, and combustion chamber
of every Vermont Castings or Majestic gas product is warranted
for life against through wall perforation. All appliances equipped
with an Insta-Flame Ceramic Burner have limited lifetime coverage on the ceramic burner plaque. Warrantees are made to the
original owner subject to proof of purchase and the conditions and
limitations listed on this Warranty Document
COMPONENT WARRANTY
CAST IRON: All external and internal cast iron parts are warranted for
a period of three years.
Note: On porcelain enamel finished external parts and accessories The Company offers no Warranty on chipping of enamel
surfaces. Inspect all product prior to accepting it for any damage
to the enamel.
The salt air environment of coastal areas or a high humidity environment can be corrosive to the porcelain enamel finish. These
conditions can cause rusting of the cast iron beneath the porcelain
enamel finish, which will cause the finish to flake off.
•
Any part and/or component replaced under the provisions of this
warranty is covered for six months or the remainder of the original
warranty, whichever is longest.
• This warranty is limited to the repair of or replacement of part(s)
found to be defective in material or workmanship, provided that
such part(s) have been subjected to normal conditions of use and
service, after said defect is confirmed by the Company’s inspection.
• The company may, at its discretion, fully discharge all obligations
with respect to this warranty by refunding the wholesale price of
the defective part(s)
• Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s), repair, replacement, or otherwise of same, will not be covered by this warranty,
nor shall the Company assume responsibility for same. Further,
the Company will not be responsible for any incidental, indirect, or
consequential damages except as provided by law.
• SOME STATES DO NOT ALLOW FOR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL AND CONSEQUENTIAL DAMAGES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY
TO YOUR CIRCUMSTANCES. THIS WARRANTY GIVES YOU
SPECIFIC RIGHTS AND YOU MAY HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
• All other warranties-expressed or implied- with respect to the
product, its components and accessories, or any obligations/liabilities on the part of the Company are hereby expressly excluded.
• The Company neither assumes, nor authorizes any third party to
assume on its behalf, any other liabilities with respect to the sale
of this Vermont Castings or Majestic product
• The warranties as outlined within this document do not apply to
chimney components or other non CFM Corporation accessories
used in conjunction with the installation of this product..
• Damage to the unit while in transit is not covered by this warranty
but is subject to claim against the common carrier. Contact the
dealer from whom you purchased your fireplace/stove (do not
operate the appliance as this might negate the ability to process
the claim with the carrier).
• The Company will not be responsible for:
a) Down drafts or spillage caused by environmental conditions
such as near-by trees, buildings, roof tops, hills, or mountains.
b) Inadequate ventilation or negative air pressure caused by mechanical systems such as furnaces, fans, clothes dryers, etc.
• This warranty is void if:
a) The fireplace has been operated in atmospheres contaminated
by chlorine, fluorine, or other damaging chemicals.
b) The fireplace has been subjected to prolonged periods of
dampness or condensation
c) Any damages to the fireplace, combustion chamber, heat
exchanger or other components due to water, or weather
damage, which is the result of but not limited to, improper
chimney/venting installation.
d) Any alteration, willful abuse, accident, or misuse of the product
has occurred.
IF WARRANTY SERVICE IS NEEDED…
1) Contact your supplier. Make sure you have your warranty, your
sales receipt, and the model/serial number of your CFM Corporation product.
fire-parts.com
Dye lot variations with replacement parts and/or accessories can
occur and are not covered by warranty.
GLASS DOORS: Glass doors are covered for a period of one year.
Glass doors are not warranted for breakage due to misuse or accident. Glass doors are not covered for discoloration or burned in
stains due to environmental issues, or improper cleaning and maintenance.
BRASS PLATED PARTS AND ACCESSORIES: Brass parts should
be cleaned with Lemon oil only. Brass cleaners cannot be used.
Mortar mix and masonry cleaners may corrode the brass finish. The
Company will not be responsible for, nor will it warrant any brass parts
which are damaged by external chemicals or down draft conditions.
GAS VALVES: Gas valves are covered for a period of one year
ELECTRONIC AND MECHANICAL COMPONENTS: Electronic and
mechanical components of the burner assembly are covered for one
year. All steel tube burners are warranted for one year.
ACCESSORIES: Unless otherwise noted all components and CFM
Corporation company supplied accessories are covered for a period
of one year.
CONDITIONS AND LIMITATIONS
•
•
•
•
30
This new Vermont Castings or Majestic product must be installed
or serviced by a qualified installer, preferably NFI or WETT
(Canada) certified, as prescribed by the local jurisdiction. It must
be installed and operated at all times in accordance with the
Installation and Operating instructions furnished with the product.
Any alteration, willful abuse, accident, or misuse of the product
shall nullify this warranty.
This warranty is non-transferable, and is made to the original
owner, provided that the purchase was made through an authorized supplier of the Company.
The customer must pay for any Authorized Dealer in-home travel
fees or service charges for in-home repair work. It is the dealers option whether the repair work will be done in the customer’s
home or in the dealer’s shop.
If upon inspection, the damage is found to be the fault of the
manufacturer, repairs will be authorized at no charge to the customer parts and/or labor.
2) DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.
20004409
Radiance Natural Vent Gas Heater
GARANTIE À VIE LIMITÉE
PRODUIT COUVERT PAR LA PRÉSENTE GARANTIE
L’ensemble des cuisinières à gaz, des poêles encastrables et des foyers à gaz Vermont Castings, ainsi que l’ensemble des foyers
à gaz de marque Majestic équipés d’un brûleur en céramique Insta-Flame ou d’un brûleur en acier standard.
GARANTIE DE BASE
La société CFM Corporation (ci-après la « Société ») garantit votre
nouveau poêle/foyer au gaz Vermont Castings ou Majestic contre
tous défauts de fabrication et de matières premières pour une
période d’un an à compter de la date d’achat, sous réserve des conditions et limitations suivantes.
GARANTIE À VIE PROLONGÉE
L’échangeur de chaleur, s’il y a lieu, ainsi que la chambre à combustion de tout produit à gaz de la société Vermont Castings ou
Majestic sont garantis pour la vie contre la perforation des parois.
Tous les produits équipés d’un brûleur en céramique Insta-Flame
comprennent une garantie à vie limitée de la plaque du brûleur en
céramique. Les garanties sont accordées à l’acheteur d’origine,
le tout sujet à une preuve d’achat et aux conditions et limitations
suivantes :
GARANTIE DES COMPOSANTS
FONTE : Toutes les pièces en fonte externes et internes sont garanties
pour une période de trois ans.
Nota : Dans le cas des pièces et accessoires externes au fini en émail de
porcelaine, la Société n’offre aucune garantie quant à l’écaillage des
surfaces en émail. Avant d’accepter un produit, inspectez-le afin de
vous assurer que les surfaces en émail ne sont pas endommagées.
L’atmosphère saline des zones côtières ou les environnements à
forte humidité peuvent provoquer la corrosion du fini en émail de
porcelaine. Ces conditions peuvent également faire rouiller la fonte
sous le fini en émail de porcelaine, provoquant ainsi l’écaillement de
la couche de fini.
Dans le cas des pièces et (ou) des accessoires de remplacement,
les variations de lots de teinture sont possibles, mais elles ne sont
pas couvertes par la garantie.
PORTES EN VERRE : Les portes en verre sont couvertes pour une
période d’un an. Les portes en verre ne sont pas garanties contre le
bris causé par un mauvais usage ou un accident. Les portes en verre
ne sont pas couvertes contre la décoloration ni contre les taches
imprégnées attribuables à des conditions environnementales ou à un
nettoyage et un entretien inadéquats.
PIÈCES ET ACCESSOIRES PLAQUÉS EN LAITON : Les pièces en
laiton ne doivent être nettoyées qu’avec de l’essence de citron. Les nettoyants pour le laiton ne doivent pas être utilisés, et les agents nettoyants pour le mortier et la maçonnerie peuvent provoquer la corrosion du
fini laiton. La Société ne pourra être tenue responsable des dommages
à toute pièce en laiton occasionnés par des conditions chimiques externes ou le refoulement, et elle n’offre aucune garantie à cet égard.
SOUPAPES À GAZ : Les soupapes à gaz sont couvertes pour une
période d’un an.
COMPOSANTS ÉLECTRONIQUES ET MÉCANIQUES : Les composants électroniques et mécaniques du brûleur sont couverts pendant
un an. Tous les brûleurs en acier sont garantis pendant un an.
ACCESSOIRES : À moins d’indication contraire, tous les composants
et accessoires fournis par CFM Corporation sont couverts pendant une
période d’un an.
CONDITIONS ET LIMITATIONS
• Ce nouveau produit Vermont Castings ou Majestic doit être installé
par un entrepreneur de service autorisé et compétent. L’installation/
le service doivent être assurés par un technicien breveté, conformément à la juridiction locale. Le produit doit être installé et utilisé en
tout temps selon les instructions d’installation et de fonctionnement
fournies avec le produit. Toute altération ou tout abus volontaire,
accident ou mauvais usage du produit annulera cette garantie.
• Cette garantie n’est pas transférable et est offerte à l’acheteur
d’origine, à condition que l’achat ait été effectué par l’entremise d’un
détaillant autorisé de la Société.
• Le client doit assumer les frais de déplacement à domicile de tout
détaillant autorisé ou les frais de service relatifs à toute réparation
effectuée à domicile. Le détaillant peut à son choix effectuer les
réparations chez le client ou à son atelier.
• Si, lors de l’inspection, on constate que les dommages sont la faute
du fabricant, les réparations, les pièces et la main-d’œuvre seront
autorisées sans frais pour le client.
Toute pièce et (ou) tout composant remplacé en vertu des dispositions de la présente garantie est couvert pour une période de
six mois ou jusqu’à l’expiration de la garantie originale, selon la
dernière des éventualités à survenir.
• Cette garantie est limitée à la réparation ou au remplacement de
toute pièce trouvée défectueuse en matières premières ou maind’oeuvre, à condition que ladite pièce ait été sujette aux conditions normales d’usage et de service, après que ledit défaut a été
confirmé par une inspection par la Société.
• La Société peut, à sa discrétion, se décharger entièrement de
toutes obligations se rapportant à cette garantie en remboursant le
prix de gros de toute pièce défectueuse.
• Tous les frais/dépenses d’installation, de main-d’oeuvre, de
construction, de transport ou autres causés par toute pièce
défectueuse, une réparation, un remplacement ou autre, ne
seront pas couverts en vertu de la présente garantie, et la Société
n’assume aucune responsabilité pour ceux-ci. De plus, la Société
ne pourra être tenue responsable de tous dommages fortuits ou
indirects, sauf là où prévu par la loi.
• CERTAINS PROVINCES NE PERMETTENT PAS L’EXCLUSION
OU LES LIMITATIONS RELATIVES AUX DOMMAGES CONSÉCUTIFS OU INDIRECTS QUANT À LA DURÉE DE TOUTE GARANTIE IMPLICITE, SI BIEN QU’IL EST POSSIBLE QUE LES LIMITATIONS CI-DESSUS NE S’APPLIQUENT PAS DANS VOTRE CAS.
LA PRÉSENTE GARANTIE VOUS DONNE DES DROITS SPÉCIFIQUES, ET IL EST POSSIBLE QUE VOUS AYEZ D’AUTRES
DROITS QUI PEUVENT VARIER D’UN ÉTAT À L’AUTRE.
• Toute autre garantie, expresse ou implicite, en ce qui a trait au
produit et ses composants et accessoires, ou toute obligation/responsabilité de la part de la Société sont expressément exclues en
vertu des présentes.
• La Société n’assume et n’autorise personne à assumer, en son
nom, toute responsabilité en ce qui a trait à la vente de ce produit
Vermont Castings ou Majestic.
• Les garanties, telles qu’elles sont décrites dans le présent document, ne s’appliquent pas aux composants de cheminée ni à
d’autres accessoires CFM Corporation utilisés conjointement avec
l’installation de ce produit.
• Les dommages causés à l’unité tandis qu’elle est en transit ne sont
pas couverts par la présente garantie, mais pourront être l’objet
d’une réclamation contre le transporteur général. Communiquez
avec le détaillant chez qui vous avez acheté votre foyer/poêle
(n’utilisez pas l’appareil étant donné que cela pourrait annuler toute
réclamation contre le transporteur).
• La Société n’engagera aucune responsabilité quant :
a) au refoulement de cheminée ou débordement causé par les
conditions environnementales (arbres, édifices, toits, coteaux ou
montagnes adjacents);
b) à une ventilation inadéquate ou une pression d’air négative
causée par des systèmes mécaniques comme les fournaises,
les ventilateurs, les sécheuses, etc.
• Cette garantie est nulle si :
a) le foyer a été utilisé dans une atmosphère contaminée par du
chlore, du fluor ou tout autre produit chimique;
b) le foyer est assujetti à de longues périodes d’humidité ou de
condensation;
c) des dommages sont causés au foyer, à la chambre de combustion, à l’échangeur de chaleur ou aux autres composants par de
l’eau ou par la température qui est le résultat mais sans y être
limité, d’une mauvaise installation de cheminée/ventilation;
d) toute altération ainsi que tout abus volontaire, accident ou mauvais usage du produit annule la présente garantie.
SI UN SERVICE SOUS GARANTIE EST REQUIS…
1) Communiquez avec votre détaillant. Assurez-vous que vous avez
votre garantie, votre reçu de caisse ainsi que le numéro de modèle/
série de votre produit CFM Corporation.
2) NE TENTEZ PAS D’EFFECTUER DES RÉPARATIONS VOUS-MÊME.
•
fire-parts.com
20004409
31
Efficiency Ratings
Model
RNVODRN
RNVODRP
EnerGuide Ratings
Fireplace Efficiency (%)
55.9
55.9
fire-parts.com
CFM Corporation
2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3
800-668-5323 • www.cfmcorp.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising