POWERSHRED® 99Ci

POWERSHRED® 99Ci
POWERSHRED 99Ci
®
Please read these instructions before use.
Do not discard: keep for future reference.
Quality Office Products Since 1917
ENGLISH
G.
A.
B.
C.
D.
Model 99Ci
H.
KEY
E.
A.SafeSense® Technology
B.Paper entry
C.See safety instructions
D.CD/Card safety flap
E.Pullout bin
F. Casters
G.Disconnect power switch
1. OFF
2. ON
F.
H. Control Panel and LEDs
1. Overheat (red)
2. Bin open (red)
3. Bin full (red)
4. Remove Paper (red)
5. SafeSense® indicator (yellow)
6. Sheet capacity indicator
7. Auto (blue)
8. Reverse
9. ON/OFF (blue)
10. Forward
CAPABILITIES
Will shred: Paper, credit cards, CD/DVDs, staples and small paper clips
Will not shred: Adhesive labels, continous form paper, transparencies, newspaper, cardboard,
large paper clips, laminates, file folders, X-rays or plastic other than noted above
Paper shred size:
Cross-Cut.............................................................................5/32” x 1-1/2” (3.9 x 38mm)
Maximum:
Sheets per pass............................................................................................................ 17*
CDs/Cards per pass........................................................................................................ 1*
Paper entry width..............................................................................................9”/230mm
*8.5”x11”, 20lb., (75g) paper at 120V, 60 Hz, 5Amps; heavier paper, humidity or other than rated
voltage may reduce capacity. Recommended daily usage rates: 1500 sheets per day, 50 credit cards;
10 CDs.
17 sheets per pass.
Fellowes SafeSense® shredders are designed to be operated in home and office environments ranging
between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
• Keep away from children and pets. Keep hands away from paper entry. Always
set to off or unplug when not in use.
• This shredder has a Disconnect Power Switch (G) that must be in the ON (I)
position to operate shredder. In case of emergency, move switch to OFF (O)
position. This action will stop shredder immediately.
• Keep foreign objects – gloves, jewelry, clothing, hair, etc. – away from shredder
openings. If object enters top opening, switch to Reverse ( ) to back out object.
• Avoid touching exposed cutting blades under shredder head.
• Never use aerosol products, petroleum based lubricants or other flammable
products on or near shredder. Do not use canned air on shredder.
• Shredder must be plugged into a properly grounded wall outlet or socket of the
voltage and amperage designated on the label. The grounded outlet or socket
must be installed near the equipment and easily accessible. Energy converters,
transformers, or extension cords should not be used with this product.
• Do not use if damaged or defective. Do not disassemble shredder.
Do not place near or over heat source or water.
• FIRE HAZARD – Do NOT shred greeting cards with sound chips or batteries.
• Operation, maintenance, and service requirements are covered in the instruction
manual. Read the entire instruction manual before operating shredders.
• For indoor use only.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment
has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
BASIC SET UP
CASTER INSTALLATION
17
AUTO
17
1
2
17
AUTO
AUTO
3
4
5
BASIC SHREDDING OPERATION
PAPER OR CD/CARD
1
Continuous operation:
25-minute maximum
NOTE: Shredder runs briefly
after each pass to clear entry.
Continuous operation beyond
25-minutes will trigger
40-minute cool down period.
2
3
4
Plug in and put disconnect power switch in ON (I) position
5
6
17
17
or
Feed paper straight into
paper entry and release
Press ( ) ON to
activate (blue)
17
To shred CDs or credit
cards rotate safety flap
into place
Hold card/CD at edge.
Feed into center of
entry and release
When finished
shredding set
to OFF ( )
Advanced product features
Patented SafeSense® Technology
Stops shredding immediately when
hands touch the paper opening.
Jam Proof System
Eliminates jams and powers
through tough jobs.
SilentShred™ Technology
SilentShred™ noise quality
shreds without noisy disruptions.
JAM PROOF SYSTEM OPERATION*
Eliminates paper jams and powers through tough jobs.
1
Advanced Jam Prevention- Electronically
measures paper thickness to prevent paper jams:
Up to RED: Too Many
sheets have been inserted.
2
3
Remove several sheets until
indicator is below red.
Continue 100% Jam
Proof Shredding
Up to YELLOW: Productivity
is optimized.
Up to GREEN: More sheets
can be added.
If a misfeed
occurs:
All indicators light up and
shredder pauses for 3-6 seconds
Wait for flashing to stop after automatic correction
is complete. Regular shredding will resume.
*100% Jam Proof when used in accordance with user manual
SAFESENSE® TECHNOLOGY OPERATION
Stops shredding immediately when hands touch the paper opening.
SET-UP AND TESTING
1
2
3
17
Turn the shredder ON
( ) to activate SafeSense®
Touch test area and
look for the SafeSense®
indicator to illuminate
17
SafeSense® is active and
working properly
illuminates after paper has been
If
reversed, press reverse and remove paper.
Otherwise, regular shredding will resume.
ENGLISH
Model 99Ci
PRODUCT MAINTENANCE
OILING SHREDDER
Cleaning Auto-Start Infrared Sensors
All cross-cut shredders require oil for peak performance. If not oiled, a
machine may experience diminished sheet capacity, intrusive noise when
shredding and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors
may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry).
TO CLEAN THE SENSORS
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
2
1
2
1
3
17
4
17
17
*Apply oil across entry
Turn off and unplug
shredder
Press and hold forward ( )
2-3 seconds
Locate Auto-start
infared sensor
Dip cotton swab in
rubbing alcohol
Using cotton swab, wipe
away any contamination
from the paper sensors
*Only use a non-aerosol vegetable oil in long
nozzle container such as Fellowes 35250
TROUBLESHOOTING
A. Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum
operating temperature and needs to cool down. This indicator will remain illuminated and the shredder will
not operate for the duration of the recovery time. See Basic Shredding Operation for more information about
the continuous operation and recovery time for this shredder.
A
B
C
D
B. Bin Open: The shredder will not run if the bin is open.
When illuminated, close the bin to resume shredding.
E
C. Bin Full: When illuminated, the shredder waste bin is full and needs to be emptied.
Use Fellowes waste bag 36053.
D. Remove Paper: When illuminated, press reverse ( ) and remove paper.
Reduce paper quantity to an acceptable amount and refeed into paper entry.
E. SafeSense® Indicator: If hands are too close to the paper entry, the SafeSense® indicator will illuminate and the shredder will stop shredding. If SafeSense® is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding.
JAM PROOF SYSTEM*
Eliminates paper jams and powers through tough jobs
DISABLING THE FEATURE
1
17
2
3
4
5
3
3
5
AUTO
Should you choose to disable the
system, press and hold the auto
button (blue) and reverse ( )
key at the same time
Once disabled, the blue
Auto light is no longer
illuminated (To re-engage,
repeat step 1)
* 100% Jam Proof when used in accordance with user manual
6
17
17
AUTO
Shredding can continue with the
system disabled, however a paper
jam may occur with too many sheets
and Remove Paper icon ( )
will illuminate
If jam occurs, press and hold
forward ( ) key until the
document is completely through
the shredder
If not cleared, press reverse
( ) briefly (repeat steps
4 and 5 until shredded)
If steps 4 and 5 do not clear
jam, reverse paper all the way
out, remove several sheets
and refeed
LIMITED PRODUCT WARRANTY
Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of
defects in material and workmanship and provides service and support for 2 years from the date
of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to be
free from defects in material and workmanship for the lifetime of the shredder. If any part is
found to be defective during the warranty period, your sole and exclusive remedy will be repair
or replacement, at Fellowes’ option and expense, of the defective part. This warranty does not
apply in cases of abuse, mishandling, failure to comply with product usage standards, shredder
operation using an improper power supply (other than listed on the label), or unauthorized
repair. Fellowes reserves the right to charge the consumers for any additional costs incurred by
Fellowes to provide parts or services outside of the country where the shredder is initially sold
by an authorized reseller. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE
WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential
or incidental damages attributable to this product. This warranty gives you specific legal rights.
The duration, terms, and conditions of this warranty are valid worldwide, except where different
limitations, restrictions, or conditions may be required by local law. For more details or to obtain
service under this warranty, please contact us or your dealer.
POWERSHRED 99Ci
®
Questions or Concerns?
www.fellowes.com
Troubleshooting
Registration
Manuals
Customer Service & Support
Troubleshooting
Replacement parts
General questions
Canada+1-800-665-4339
Mexico+1-800-234-1185
United States
©2011 Fellowes, Inc. Part No. 406775
+1-800-955-0959
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising