327009 - PUP-1500-2500-3500 - 94-96

327009 - PUP-1500-2500-3500 - 94-96
TM
Ram Truck - 1500/2500/3500
www.installdr.com
Dodge/Chrysler/Plymouth
1994
thru 1996
Radio Replacement
Document #: 327025
I
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Factory Radio
Other Documents Available For This Vehicle:
No other documents available at this time
Adobe Acrobat Reader Printing Tips:
New Radio
and dash installation kit
1) Select “FILE” then “PRINT” and select your printer.
2) In the print options box do the following:
A) Locate check box “Shrink to Fit”. Place check in box.
B) Locate box “Print Quality”. Select highest print dpi
allowed by printer.
C) If print quality listed is not as high as that printers normal
quality, press the “SETUP..” button. In the next screen,
press the “PROPERTIES” button and set the printers
print quality to the highest print dpi allowed.
Document Revision History
02/2000 Document Creation
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
TM
Ram Truck - 1500/2500/3500
www.installdr.com
Dodge/Chrysler/Plymouth
Radio Replacement
Document #: 327025
1994
thru 1996
I
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Overview Of This Radio Install
Step
Remove old radio from dash
Wire the new radio
Mount the new radio
Finishing the installation
Parts Needed For This Radio Install
What Section To Go To
Remove & Install
Wire New Radio
Mount New Radio
Step By Step
Parts REQUIRED for the install
Dash installation kit
Snap on wire harness adapter
Description
Multi purpose Dodge/Chrysler
Dodge/Chrysler/Plymouth 2 pc.
Optional parts for this install
None
Tools Needed To Complete This Install
TOOL TIPS:
10 mm
Socket
Solder/
Crimper
Hand tools needed
to remove radio
Voltage
Meter
Small
Battery
Accessory tools needed to test and
wire the new radio
PLUS: Wire ties or electrical tape: to neatly bundle and organize your
wires for a professional appearance.
Small Battery: use a battery to test speaker wires. Touching the (+) positive
and (-) negative baterry leads to a pair of speaker will cause the speaker to
make a “Pop” sound indicating that pair of wires goes to that speaker.
Voltage Meter: Always check +12 Volt power wires for voltage before
making wire connections. These wires will fluctuate between 10 and 14 Volts.
Solder Iron or Crimp Tool: make wire to wire connections using either a
solder iron and electrical tape, OR plastic crimp terminals found at most
hardware or auto parts stores.
Installation Difficulty Ratings
Easy. No advanced skills or specialty tools needed.
Basics. Simple tools required. Installs quickly.
Intermediate. Requires knowledge of tools, or disassembly of panels.
Advanced. Requires advanced tools, or extra time.
Difficult. Involves modifying or cutting of the installation area. Advanced
tools and/or skills required. Best if performed by experienced installers.
Do It Yourselfers
Basics
Professional Installer
Basics
Support Information If You Need Help
Supplemental information if you need help
Document Title
Basic DC electronics for automotive applications
Wire splicing: soldering vs. crimping
Why use radio installation kits
Mounting your radio to an installation kit
Why use an OEM snap on wire harness
Wiring your new radio using a wire harness
Testing wires when installing a new radio
Document #
999001
999004
999005
999007
999008
999009
999013
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
TM
Ram Truck - 1500/2500/3500
www.installdr.com
Dodge/Chrysler/Plymouth
Radio Replacement
Document #: 327025
1994
thru 1996
I
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Remove Factory Radio
STEP 1:
To remove the radio, the entire plastic dash panel surrounding the radio and dash instruments
must be removed.
Pull out the ashtray. Locate and remove two (2) phillips screws securing the ashtray bracket.
Pull out the ashtray bracket and set it aside.
STEP 2:
Open the drink tray. Locate and remove two (2) phillips screws hidden behind the front panel of
the drink tray. Once the screws are removed, pull out the entire drink tray assembly and set it
aside.
STEP 3:
Once the screws securing the ashtray bracket and drink tray assembly have been removed, the
entire dash panel can be removed.
The dash panel simply unsnaps from the dash. Start at the top of the dash at one corner and
pull gently until the dash separates from the body of the main dash.
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
TM
Ram Truck - 1500/2500/3500
www.installdr.com
Dodge/Chrysler/Plymouth
I
1994
thru 1996
Radio Replacement
Document #: 327025
Cover
Page
Click on a link
tab to jump to
that page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
STEP 4:
STEP 5:
The radio is secured to the dash with two
(2) 10mm bolts. Locate and remove both.
Pull the radio out of the dash. Unplug the
black cable plugged into the rear of the radio.
Unplug two plastic wire harness connectors
(1 black, 1 gray) snapped into the rear of the
radio. Some years of this vehicle have a
metal braid bolted to the rear of the radio.
Remove the braid by removing the 10mm
bolts that secures it to the rear of the radio.
Mounting The Radio To A Kit
Wiring The New Radio
Move to: Mount New Radio Section
Move to: Wire New Radio Section
Completing The Radio Installation
STEP 1:
STEP 2:
Insert the radio/kit assembly into the opening
in the dash.
Reattach the plastic dash panel back onto the
main body of the dash.
Plug in the antenna cable into the rear of the
new radio. Make sure all wire connections
to the new radio have been completed and
connect any connectors into the rear of the
new radio.
The installation is now complete.
Secure the kit into the dash with the same
two 10mm bolts that had originally secured
the factory radio.
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
TM
Ram Truck - 1500/2500/3500
www.installdr.com
Dodge/Chrysler/Plymouth
1994
thru 1996
Radio Replacement
Document #: 327025
I
Cover
Page
Click on a link
tab to jump to
that page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Step By Step Wiring
Page 1 of 2
Auto Makers
Factory
Radio
New Radio
Wire Harness Inside Vehicles
Dash Which Plugs Into The
Rear Of The Factory Radio
Optional Snap On Wire Harness
(Strongly Recommended)
That Splices Into The Wires Of
The New Radio
(Note: the radio shown is for display purposes and may not be similar in
size or dimensions than the auto makers factory radio in your vehicle)
Wiring Instructions:
The power and speaker wires needed to connect the new radio are attached to
the connector of the wire harness located inside the vehicles dash. The Install
Doctor STRONGLY recommends using an optional snap on wire harness that
is specifically designed to snap into the vehicles dash wire harness connector.
This will keep you from cutting the vehicles wires. This optional snap on wire
harness will have wires on the opposite side of the connector that will allow
you to splice these wires to the new radios wires. The only other option is to
cut off the vehicles dash wire harness connector and splice the new radios
wires directly to these wires. The optional snap on wire harness takes all the
guess work out of trying to figure out what each wire is in the vehicles dash
wire harness. The optional snap on wire harness tell you what each wire is.
Supplemental information if you need help
Document Title
Testing wires when installing a new radio
Why use an OEM snap on wire harness
Wiring your new radio using a wire harness
Wire splicing: soldering vs. crimping
Document #
999013
999008
999009
999004
STEP 1
Ground Wire
STEP 2
+12 Volt
Battery Wire
Connect the +12 Volt Battery or Constant wire of the new radio to
either the +12 Volt Battery wire of a snap on wire harness OR connect
this wire to the +12 Volt Battery wire found in the wire chart above.
+12 Volt
Battery Wire
STEP 3
+12 Volt
Ignition Wire
Connect the +12 Volt Ignition or Switch wire of the new radio to
either the +12 Volt Ignition wire of a snap on wire harness OR connect
this wire to the +12 Volt Ignition wire found in the wire chart above.
+12 Volt
Ignition Wire
STEP 4
Power Antenna
Wire (if available)
If your vehicle has a POWER ANTENNA connect the
POWER ANTENNA wire of the new radio to either the POWER
ANTENNA wire on a snap on wire harness OR wire in chart above.
Power Antenna
Wire (if available)
STEP 5
Left Front Speaker Wires
Connect the LEFT FRONT speaker wires from the new radio to the
LEFT FRONT speaker wires on a snap on wire harness OR the
LEFT FRONT speaker wires found in the chart above.
Left Front Speaker Wires
STEP 6
Right Front Speaker Wires
Connect the RIGHT FRONT speaker wires from the new radio to the
RIGHT FRONT speaker wires on a snap on wire harness OR the
RIGHT FRONT speaker wires found in the chart above.
Right Front Speaker Wires
STEP 7
Left Rear
Speaker Wires
Connect the LEFT REAR speaker wires from the new radio to the
LEFT REAR speaker wires on a snap on wire harness OR the
LEFT REAR speaker wires found in the chart above.
Left Rear
Speaker Wires
STEP 8
Right Rear Speaker Wires
Connect the RIGHT REAR speaker wires from the new radio to the
RIGHT REAR speaker wires on a snap on wire harness OR the
RIGHT REAR speaker wires found in the chart above.
POWER AND SPEAKER WIRES FROM THE VEHICLES
DASH WIRE HARNESS OR SNAP ON WIRE HARNESS
POWER AND SPEAKER WIRES FROM NEW RADIO
Ground Wire
See the TIP on the following page regarding how to connect the
ground wire.
Right Rear Speaker Wires
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
TM
Ram Truck - 1500/2500/3500
www.installdr.com
Dodge/Chrysler/Plymouth
1994
thru 1996
Radio Replacement
Document #: 327025
I
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Radio Wire & Color Code Information
Page 2 of 2
Factory in-dash wire harness (this vehicle has a 2 pc harness)
that snaps into the factory radio
Black Plug
A
B
C
D
E
F
G
H
I
J
K
L
M
N
Gray Plug
AS VIEWED FROM MATING END OF CONNECTOR
Pin
What It Is
Typical Dodge/Chrysler
In Dash Wire Color
Typical New Radio
Equivalent Wire Color
A
Right Rear Spkr (-)
Blue w/ White Stripe
Purple w/ Black Stripe
B
Left Rear Spkr (-)
Brown w/ Yellow Stripe
Green w/ Black Stripe
C
Right Front Spkr (+)
Purple
Gray
D
Left Front Spkr (+)
Dark Green
White
E
Right Rear Spkr (+)
Blue w/ Orange Stripe
Purple
F
Left Rear Spkr (+)
Brown w/ Blue Stripe
Green
G
Power Antenna/Amp
White (use for Infinity Radio) Blue
H
+12 Volt Battery Wire
Pink or Pink w/ White Stripe Yellow
I
+12 Volt Ignition Wire
Red w/ White Strip
Red
J
Radio Dimmer Wire
Do Not Use
K
Headlight Dimmer Wire
Do Not Use
L
Right Front Spkr (-)
Blue w/ Red Stripe
Gray w/ Black Stripe
M
Left Front Spkr (-)
Brown w/ Red Stripe
White w/ Black Stripe
N
No Wire
Metal Braid Or Plastic Connector Attached To Back Of Radio Is The Ground Wire
Black (see TIP)
If your original radio had a braided strap bolted to the rear of the radio.
TIP:
Crimp a ring terminal to the new radios ground wire
and insert a bolt through both connectors to connect
the ring terminal of the braided ground wire to the
ring terminal attached to the new radios ground wire.
If your original radio had a plastic connector containing a single wire plugged into the rear of the radio.
TIP:
Crimp a male tab spade to the new radios
ground wire. Slide it into the female tab spade
connector that had originally snapped into the
rear of the factory radio.
If your original radio or speaker grills were labeled or marked with ‘INFINITY’
TIP:
Crimp a male tab spade to the new radios
ground wire. Slide it into the female tab spade
connector that had originally snapped into the
rear of the factory radio to activate the ‘Infinity’
sound system.
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
TM
Ram Truck - 1500/2500/3500
www.installdr.com
Dodge/Chrysler/Plymouth
Radio Replacement
Document #: 327025
1994
thru 1996
I
Click on a link
tab to jump to
that page
Cover
Page
Before
You Begin
Remove
& Install
Wire
New Radio
Mount
New Radio
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
Mounting A Radio To A Dash Kit
All information needed to complete the mounting of the new
radio to the installation kit is included on this sheet. If you need
additional help, please consult the following tech documents:
NOTE:
Before you begin: A word about the radio installation kit you are about to
install. There are many manufacturers of radio installation kits for this vehicle.
Each manufacturer produces slightly different variations of the same kit, and a
few make individual kits for specific vehicles. The pictured installation kit shown in the
illustrations below is a standard kit used for many Dodge/Chrysler/Plymouth vehicles. Radio
installation kits change with the model and years of production of the vehicle. When
selecting a kit for this vehicle, make sure the kit you purchase states on the package the
installation kit will work with your vehicle model and year. Some kits may require additional
setup. Certain kits may be multi function kits designed to work with multiple vehicles and
may require the installer to remove break away screw mounting tabs attached to the kit that
are not required for your particular vehicle.
Document Title
Why use radio installation kits
Mounting your radio to an installation kit
Radio security
Document #
999005
999007
999010
Follow the instructions below for your type of radio
Shafted Radios
‘DIN’ Radios (Rectangular Body Style)
What you need to mount your radio
Installation dash kit for
shafted style radios
Installation dash kit for ‘DIN’
(rectangular body style) radios
New Radio
Slide the radios
installation
sleeve into the
mounting kit.
(some sleeves
may be marked
with “TOP” to
note the top of
the sleeve)
New radios installation sleeve
When the installation sleeve is fully inserted
and the front edge or lip is seated against
the front face of the installation kit, bend the
tabs of the installation sleeve behind the
rear surface of
the installation kit to
secure the
installation sleeve.
Bending the tabs
secures the sleeve
to the kit.
Front edge or lip of installation sleeve. Slide installation sleeve
into the mounting kit until the front edge or lip meets the
installation kit.
Radio slides into sleeve after the sleeve
is secured to the installation kit
New Radios
Face Plate
Slide the radio through
the backside of the
installation kit. Slide
the radios front face
plate onto the front
surface of the
installation kit. Notice
how much of the
radios shafts are
protruding past the front of the kit. You will need to
remove the excess by adjusting the depth of the
new radios shaft spin nuts. Pull the radio out of the
installation kit and spin on the nuts that are included
with the radio. Slide the radio back into the
installation kit. Adjust the nuts by spinning them
forward or back to adjust the depth that the new
radios shafts protrude out the front of the kit. To
assure a “flush” and professional appearance, make
sure that the new radios front face plate is flush with
the new radios display box that is visible through the
opening of the installation kit. Complete the
installation by securing the front face plate with the
remaining nuts provided with the new radio. The
new radio is secured to the installation kit by
“sandwiching” the installation kit between the new
radios front face plate and the nuts spun onto the
shafts of the radio behind the installation kit.
CAUTION:
TIP:
Do not overtighten the
spin nuts securing the front
face plate. Tighten to
secure the radio without
cracking the plastic.
If your radio manufacturer
provides 6 spin nuts, use 4 to
secure the radio to the
installation kit and 2 to secure
the front face plate.
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As General Information For The Installation Of Audio, Video, Security,
Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries
Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should Be Checked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed
And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising