Supermicro SUPERSERVER 6014H-32 User`s manual

SUPER
®
SUPERSERVER 6014H-32
USER’S MANUAL
1.0a
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
SUPER MICRO COMPUTER reserves the right to make changes to the product described in this
manual at any time and without notice. This product, including software, if any, and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any
medium or machine without prior written consent.
IN NO EVENT WILL SUPER MICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE
OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING
OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for
all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0a
Release Date: September 24, 2007
Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2007 by SUPER MICRO COMPUTER INC.
All rights reserved.
Printed in the United States of America
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SuperServer 6014H-32. Installation and maintainance should be performed by experienced technicians only.
The SuperServer 6014H-32 is a high-end 1U rackmount server based on the
SC813T-500 1U rackmount server chassis and the X6DHR-3G2 serverboard, which
supports single or dual Intel® Xeon™ processors of up to 3.60 GHz at a Front Side
(system) Bus speed of 800 MHz and up to 16 GB of DDR2-400 SDRAM memory.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the server system and describes the main features of the SUPER X6DHR-3G2 serverboard
and the SC813T-500 chassis, which make up the SuperServer 6014H-32.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 6014H-32 into
a rack and check out the server configuration prior to powering up the system. If
your server was ordered without processor and memory components, this chapter
will refer you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
iii
SUPERSERVER 6014H-32 User's Manual
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6014H-32.
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X6DHR-3G2 serverboard, including the locations and functions of connectors, headers and jumpers. Refer to this
chapter when adding or removing processors or main memory and when reconfiguring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the 1U SC813T-500 rackmount server
chassis. You should follow the procedures given in this chapter when installing,
removing or reconfiguring SAS/SATA or peripheral drives and when replacing the
system power supply unit and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed information on running the CMOS Setup Utility.
Appendix A: BIOS POST Codes
Appendix B: Software Installation
Appendix C: System Specifications
iv
Preface
Notes
v
SUPERSERVER 6014H-32 User's Manual
Table of Contents
Preface
About This Manual ...................................................................................................... iii
Manual Organization ................................................................................................... iii
Chapter 1: Introduction
1-1
Overview ......................................................................................................... 1-1
1-2
Serverboard Features ..................................................................................... 1-2
1-3
Server Chassis Features ................................................................................ 1-4
1-4
Contacting Supermicro ................................................................................... 1-6
Chapter 2: Server Installation
2-1
Overview ......................................................................................................... 2-1
2-2
Unpacking the System ................................................................................... 2-1
2-3
Preparing for Setup ........................................................................................ 2-1
Choosing a Setup Location .................................................................... 2-2
Rack Precautions .................................................................................... 2-2
Server Precautions ................................................................................. 2-2
Rack Mounting Considerations ............................................................... 2-3
2-4
Installing the System into a Rack ................................................................... 2-3
Identifying the Sections of the Rails ....................................................... 2-3
Installing the Rack Rails............................................................................ 2-4
Installing the Chassis Rails ....................................................................... 2-5
Installing the Server into the Rack ............................................................ 2-6
Installing the Server into a Telco Rack ..................................................... 2-7
2-5
Checking the Serverboard Setup ................................................................... 2-8
2-6
Checking the Drive Bay Setup ....................................................................... 2-9
Chapter 3: System Interface
3-1
Overview ......................................................................................................... 3-1
3-2
Control Panel Buttons .................................................................................... 3-1
Reset ....................................................................................................... 3-1
Power ...................................................................................................... 3-1
3-3
Control Panel LEDs ........................................................................................ 3-2
Overheat/Fan Fail
.................................................................................. 3-2
NIC2 .......................................................................................................... 3-2
NIC1 .......................................................................................................... 3-2
HDD ........................................................................................................ 3-3
vi
Table of Contents
Power ...................................................................................................... 3-3
3-4
SAS/SATA Drive Carrier LED .......................................................................... 3-3
Chapter 4: System Safety
4-1
Electrical Safety Precautions ........................................................................... 4-1
4-2
General Safety Precautions ............................................................................. 4-2
4-3
ESD Precautions ............................................................................................ 4-3
4-4
Operating Precautions ..................................................................................... 4-4
Chapter 5: Advanced Serverboard Setup
5-1
Handling the Serverboard ................................................................................ 5-1
5-2
Processor and Heatsink Installation ................................................................ 5-2
5-3
Connecting Cables .......................................................................................... 5-4
Connecting Data Cables ........................................................................... 5-4
Connecting Power Cables ......................................................................... 5-4
Connecting the Control Panel ................................................................... 5-5
5-4
I/O Ports........................................................................................................... 5-6
5-5
Installing Memory............................................................................................. 5-6
5-6
Adding PCI Cards ............................................................................................ 5-8
5-7
Serverboard Details ......................................................................................... 5-9
X6DHR-3G2 Layout ................................................................................ 5-9
X6DHR-3G2 Quick Reference .............................................................. 5-10
5-8
Connector Definitions .................................................................................... 5-11
ATX Power Connection ......................................................................... 5-11
PWR_SEC Connection ......................................................................... 5-11
Processor Power Connection ............................................................... 5-11
NMI Button ............................................................................................ 5-11
Power LED ............................................................................................ 5-11
HDD LED................................................................................................. 5-12
NIC1 LED .............................................................................................. 5-12
NIC2 LED .............................................................................................. 5-12
Overheat/Fan Fail LED ........................................................................... 5-12
Power Fail LED ....................................................................................... 5-12
Reset Button .......................................................................................... 5-13
Power Button ........................................................................................... 5-13
Universal Serial Bus ................................................................................ 5-13
Chassis Intrusion ..................................................................................... 5-13
Serial Ports .............................................................................................. 5-14
Power Supply Fail Header ...................................................................... 5-14
Fan Headers............................................................................................ 5-14
vii
SUPERSERVER 6014H-32 User's Manual
Extra USB Headers ................................................................................. 5-15
Power LED/Speaker ................................................................................ 5-15
ATX PS/2 Keyboard & Mouse Ports ....................................................... 5-15
JLAN 1/2 (Ethernet Ports) ........................................................................ 5-15
Wake-On-LAN ......................................................................................... 5-16
Wake-On-Ring ......................................................................................... 5-16
SMB ......................................................................................................... 5-16
SMB Power ............................................................................................. 5-16
5-9
Jumper Settings ............................................................................................. 5-17
Explanation of Jumpers ........................................................................... 5-17
CMOS Clear ............................................................................................ 5-17
VGA Enable/Disable ................................................................................ 5-17
JLAN Enable/Disable .............................................................................. 5-18
3rd Power Supply Fail Detect Enable/Disable ........................................ 5-18
Alarm Reset ........................................................................................... 5-18
Watch Dog Enable/Disable ..................................................................... 5-19
Compact Flash Master/Slave ................................................................. 5-19
SAS Controller Enable/Disable .............................................................. 5-19
5-10 Onboard Indicators ........................................................................................ 5-20
JLAN1/JLAN2 LEDs ................................................................................ 5-20
SAS Activity LED Indicators ................................................................... 5-20
5-11 SATA, Floppy and Hard Drive Connections .................................................. 5-21
Floppy Connector .................................................................................... 5-21
IDE Connectors ....................................................................................... 5-22
SATA Connectors ................................................................................... 5-22
Chapter 6: Advanced Chassis Setup
6-1
Static-Sensitive Devices .................................................................................. 6-1
6-2
Control Panel ................................................................................................... 6-2
6-3
System Fans .................................................................................................... 6-3
System Fan Failure ................................................................................... 6-3
Replacing System Cooling Fans ............................................................... 6-3
6-4
Drive Bay Installation/Removal ........................................................................ 6-4
Removing the Front Bezel ........................................................................ 6-4
Accessing the Drive Bays ......................................................................... 6-5
SAS/SATA Drive Installation ...................................................................... 6-6
CD-ROM and Floppy Drive Installation ..................................................... 6-8
6-5
Power Supply................................................................................................... 6-9
Power Supply Failure ................................................................................ 6-9
viii
Table of Contents
Removing/Replacing the Power Supply .................................................... 6-9
Chapter 7: BIOS
7-1
Introduction ....................................................................................................... 7-1
7-2
Running Setup .................................................................................................. 7-2
7-3
Main BIOS Setup ............................................................................................. 7-2
Main BIOS Setup Menu ............................................................................. 7-3
7-4
Advanced Setup .............................................................................................. 7-6
7-5
Security .......................................................................................................... 7-16
7-6
Boot ............................................................................................................... 7-17
7-7
Exit ................................................................................................................. 7-18
Appendices:
Appendix A: BIOS POST Codes
Appendix B: Software Installation
Appendix C: System Specifications
ix
SUPERSERVER 6014H-32 User's Manual
Notes
x
Chapter 1: Introduction
Chapter 1
Introduction
1-1
Overview
The Supermicro SuperServer 6014H-32 is a high-end dual processor, 1U rackmount
server featuring some of the most advanced technology currently available. The
SuperServer 6014H-32 is comprised of two main subsystems: the SC813T-500 1U
rackmount chassis and the X6DHR-3G2 Xeon dual processor serverboard. Please
refer to our web site for information on operating systems that have been certified
for use with the SuperServer 6014H-32. (www.supermicro.com)
In addition to the mainboard and chassis, various hardware components may have
been included with your SuperServer 6014H-32, as listed below:
One (1) slim floppy drive [FPD-TEAC-S(B)]
One (1) slim CD-ROM drive [CDM-TEAC-24(B)]
Two (2) riser cards (CSE-RR1U-X and CSE-RR1U-XLP)
Two (2) 10-cm blower fans (FAN-0059)
SAS (Serial Attached SCSI) and Serial ATA (SATA) Accessories:
One (1) SAS/SATA backplane (CSE-SATA-813)
Four (4) SAS/SATA data cables (CBL-0119)
Four (4) SAS/SATA drive carriers [CSE-PT39(B)]
Rackmount hardware with screws (CSE-PT51):
Two (2) rack rail assemblies
Six (6) brackets for mounting the rack rails to a rack/telco rack
One (1) CD containing drivers and utilities
Optional: Two (2) passive 1U CPU heatsinks (SNK-P0009)
One (1) front bezel [CSE-PTFB-813(B)]
SuperServer 6014H-32 User's Manual
Note: a "B" at the end of a part number indicates the item is available in black.
1-1
SUPERSERVER 6014H-32 User's Manual
1-2
Serverboard Features
At the heart of the SuperServer 6014H-32 lies the X6DHR-3G2 a dual Xeon processor serverboard designed to provide maximum performance. Below are the
main features of the X6DHR-3G2. See Figure 1-1 for a system block diagram of
the chipset.
Processors
The X6DHR-3G2 supports single or dual 604-pin Intel Xeon processors of up to
3.60 GHz at an 800 MHz FSB. Please refer to our web site for a complete listing
of supported processors.
Memory
The X6DHR-3G2 has eight 240-pin DIMM slots that can support up to 16 GB of
DDR2-400 SDRAM. The dual-channel memory bus requires memory modules
to be installed two at a time.
Serial Attached SCSI/Serial ATA
An Adaptec 9410W SAS/SATA controller is integrated into the X6DHR-3G2 to
provide a four-port Serial Attached SCSI/Serial ATA subsystem, which supports
RAID levels 0 and 1, 10 and JBOD. The X6DHR-3G2 also has a slot for a LP
ZCR daughter card (AOC-SOZCR1) to supply ZCR function. The use of a ZCR
card in this slot will also provide RAID 5 support.
Note: The operating system you use must have RAID support to enable the hotswap capability and RAID function of the SAS/SATA drives.
PCI Expansion Slots
Two riser cards have been included with the server to support PCI expansion.
The CSE-RR1U-X riser fits into the 133 MHz PCI-X slot on the X6DHR-3G2 to
support a standard size (full-height, full-length) PCI-X add-on card (any speed).
The CSE-RR1U-XLP fits into the 100 MHz PCI-X slot to support one low profile
(half-height, half-length) PCI-X add-on card (of either 100 or 66 MHz).
An additional two riser cards are available as an option to support add-on cards
in the SXB x8 PCI-E slots (CSE-RR1U-EL and CSE-RR1U-ELP).
1-2
Chapter 1: Introduction
ATI Graphics Controller
An ATI video controller based on the Rage XL 8 MB graphics chip is integrated
onboard the X6DHR-3G2. Rage XL fully supports sideband addressing and AGP
texturing. This onboard graphics package can provide a bandwidth of up to 512
MB/sec over a 32-bit graphics memory bus.
Onboard Controllers/Ports
The X6DHR-3G2 provides one floppy drive controller and two onboard IDE controllers, which support up to four hard drives or ATAPI devices. Backpanel I/O
ports include one COM port, two USB ports, PS/2 mouse and keyboard ports and
a video (monitor) port. An Intel 82546GB Ethernet controller is also included to
support two gigabit LAN ports.
Other Features
Other onboard features are included to promote system health. These include
various voltage monitors, two CPU temperature sensors, four fan speed sensors,
a chassis intrusion header, auto-switching voltage regulators, chassis and CPU
overheat sensors, virus protection and BIOS rescue.
1-3
SUPERSERVER 6014H-32 User's Manual
1-3
Server Chassis Features
The SC813T-500 is one of Supermicro's third-generation 1U chassis and features
four hot-swap SAS/SATA drive bays, a slim CD-ROM drive, a slim 3.5" floppy drive
and a revolutionary cooling design that can keep today's most powerful processors
running well below their temperature thresholds. The following is a general outline
of the main features of the SC813T-500 chassis.
System Power
The SC813T-500 chassis includes a single 500W cold-swap power supply.
SAS/SATA Subsystem
For the 6014H-32, the SC813T-500 chassis was designed to support four SAS or
four SATA hard drives, which are hot-swappable units.
Note: The operating system you use must have RAID support to enable the hotswap capability of the SAS/SATA drives.
Control Panel
The SC813T-500 control panel provides important system monitoring and control
information. LEDs indicate power on, network activity, hard disk drive activity
and system overheat conditions. Also present are a main power button and a
system reset button.
I/O Backplane
The SC813T-500 is a 1U rackmount chassis. Its I/O backplane provides one fullheight full-length and one half-height half-length slots for PCI add-on cards, one
COM port (the other is internal), one VGA port, two USB ports, PS/2 mouse and
keyboard ports and two Ethernet (LAN) ports.
Cooling System
The SC813T-500 chassis' revolutionary cooling design has been optimized to
provide sufficient cooling for dual Xeon configurations. The SC813T-500 includes
two heavy duty 10-cm blower fans located in the middle of the chassis. In the
event of a fan failure, the ambient air temperature inside the chassis will rise and
activate an overheat LED.
1-4
Chapter 1: Introduction
Figure 1-1. Intel E7520 Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
EM64T NOCONA CPU#1
VRM
DATA
CTRL
ADDR
VRM
Clock
EM64T NOCONA CPU#1
ADDR
CTRL
DATA
ADDR
CTRL
DATA
PCI EXP. B(X8)
6.4GB/s
PCI-E_(X8)
PCI EXP. B(X8)
4GB/s
Gbit LAN
ANVIK
B
1_PCI-X133
SLOT--6
1_PCI-X100
SLOT--7
SATA
PCI-X BUS(133MHZ)
PCI-X BUS(100MHZ)
A
PXH#2
B
PCI EXP. A(X8)
C
6.4GB/s
MCH
A
B
4_DDR266/333
DIMMs
PCI EXP. C(X8)
PCI-E_(X8)
4 Ports
ZCR
SOCKET
4_DDR266/333
DIMMs
A
HUB 266MB/s
IDE
PRI/SEC
UDMA-100
PCI BUS(32-BIT)
ICH5R
SATA
0, 1
VGA
SATA
LPC BUS
USB PORTS
USB
0,1,2,3
LPC I/O
KB.
MS.
FDD.
1-5
FWH
SER.1
SER.2
H/W
MONITOR
BMC CON.
SUPERSERVER 6014H-32 User's Manual
1-4
Contacting Supermicro
Headquarters
Address:
Tel:
Fax:
Email:
Web Site:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
+1 (408) 503-8000
+1 (408) 503-8008
[email protected] (General Information)
[email protected] (Technical Support)
www.supermicro.com
Europe
Address:
Tel:
Fax:
Email:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
+31 (0) 73-6400390
+31 (0) 73-6416525
[email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacific
Address:
Super Micro, Taiwan
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei, Taiwan, R.O.C.
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3991
Web Site:
www.supermicro.com.tw
Technical Support:
Email:
[email protected]
Tel:
886-2-8228-1366, ext.132 or 139
1-6
Chapter 2: Server Installation
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 6014H-32
up and running. Following these steps in the order given should enable you to
have the system operational within a minimum amount of time. This quick setup
assumes that your SuperServer 6014H-32 system has come to you with the processors and memory preinstalled. If your system is not already fully integrated with a
serverboard, processors, system memory etc., please turn to the chapter or section
noted in each step for details on installing specific components.
2-2
Unpacking the System
You should inspect the box the SuperServer 6014H-32 was shipped in and note
if it was damaged in any way. If the server itself shows damage you should file a
damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer 6014H32. It should be situated in a clean, dust-free area that is well ventilated. Avoid
areas where heat, electrical noise and electromagnetic fields are generated. You
will also need it placed near a grounded power outlet. Read the Rack and Server
Precautions in the next section.
2-3
Preparing for Setup
The box the SuperServer 6014H-32 was shipped in should include two sets of rail
assemblies, two rail mounting brackets and the mounting screws you will need to
install the system into the rack. Follow the steps in the order given to complete
the installation process in a minimum amount of time. Please read this section
in its entirety before you begin the installation procedure outlined in the sections
that follow.
2-1
SUPERSERVER 6014H-32 User's Manual
Choosing a Setup Location
- Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches).
- Leave approximately 30 inches of clearance in the back of the rack to allow for
sufficient airflow and ease in servicing.
- This product is for installation only in a Restricted Access Location (dedicated
equipment rooms, service closets, etc.).
- This product is not suitable for use with visual display work place devices according
to §2 of the the German Ordinance for Work with Visual Display Units.
!
Warnings and Precautions!
!
Rack Precautions
• Ensure that the leveling jacks on the bottom of the rack are fully extended to the
floor with the full weight of the rack resting on them.
• In single rack installation, stabilizers should be attached to the rack.
• In multiple rack installations, the racks should be coupled together.
• Always make sure the rack is stable before extending a component from the
rack.
• You should extend only one component at a time - extending two or more simultaneously may cause the rack to become unstable.
Server Precautions
• Review the electrical and general safety precautions in Chapter 4.
• Determine the placement of each component in the rack before you install the
rails.
• Install the heaviest server components on the bottom of the rack first, and
then work up.
• Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
• Allow the hot plug SAS/SATA drives and power supply units to cool before touching them.
• Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
2-2
Chapter 2: Server Installation
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient temperature
of the room. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated
ambient temperature (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does
not arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might
have on overcurrent protection and power supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this
concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).
2-3
SUPERSERVER 6014H-32 User's Manual
2-4
Installing the System into a Rack
This section provides information on installing the SuperServer 6014H-32 into a
rack unit with the rack rails provided. If the 6014H-32 has already been mounted
into a rack, you can skip ahead to Sections 2-5 and 2-6. There are a variety of
rack units on the market, which may mean the assembly procedure will differ
slightly. You should also refer to the installation instructions that came with the
rack unit you are using.
Identifying the Sections of the Rails
You should have received a rack mounting kit with the SuperServer 6014H-32.
The kit includes two sets of chassis rails (four pieces total, two of which are
already installed on the chassis) and two sets of rack rails (four pieces total).
Figure 2-1 displays the two right-side chassis rails and the two right-side rack
rails. Note that two of the four chassis rails (Chassis Rail 1) are already attached
to the chassis.
Installing the Rack Rails
Begin by joining one set of rack rails corresponding to either the left or the right side
of the rack. Do this by aligning the studs of one rail with the holes of the other rail.
Push the studs into the grooved holes and then push the rail to slide the studs to
the end of the groove. Repeat this with the rack rails used for the other side.
Next, determine where you want to place the SuperServer 6014H-32 in the rack.
(See Rack and Server Precautions in Section 2-3.) Position the assembled rack
rails at the desired location in the rack. Screw the assembly securely to the rack
using the brackets provided. Attach the other assembly to the other side of the
rack, making sure both are at the exact same height and with the rail guides facing inward.
Locking Tabs: Both of the two chassis rails on each side have a locking tab (four
total), which serves two functions. The first is to lock the server into place when
installed and pushed fully into the rack, which is its normal operating position.
Secondly, these tabs also lock the server in place when extended from the rack.
This prevents the server from coming completely out of the rack when you pull it
out for servicing. The two sets of locking tabs mean there are two locked positions
when the chassis is extended from the rack, allowing easy access when servicing
the system. Note that on one side, you push the locking tab up to release it and
on the other side you push it down to release.
2-4
Chapter 2: Server Installation
Installing the Chassis Rails
Two of the chassis rails (Chassis Rail 1) should have already been preattached
- one to each side of the chassis. Attach the second set of chassis rails (Chassis
Rail 2) directly to the chassis with the screws provided. Chassis Rail 2 should
be positioned just behind Chassis Rail 1 (see Figure 2-2). Do this for both sides
of the chassis.
Figure 2-1. Identifying the Sections of the Rails
Figure 2-2. Installing Chassis Rails
2-5
SUPERSERVER 6014H-32 User's Manual
Installing the Server into the Rack
You should now have rails attached to both the chassis and the rack unit. The
next step is to install the server into the rack. Do this by lining up the rear of the
chassis rails with the front of the rack rails. Slide the chassis rails into the rack
rails, keeping the pressure even on both sides (you may have to depress the locking tabs when inserting). See Figure 2-3.
When the server has been pushed completely into the rack, you should hear the
locking tabs "click". Finish by inserting and tightening the thumb screws that hold
the front of the server to the rack.
Figure 2-3. Installing the Server into a Rack
2-6
Chapter 2: Server Installation
Installing the Server into a Telco Rack
To install the SuperServer 6014H-32 into a Telco type rack, use two L-shaped
brackets on either side of the chassis (four total). First, determine how far the
server will extend out the front of the rack. Larger chassis should be positioned to
balance the weight between front and back. If a bezel is included on your server,
remove it. Then attach the two front brackets to each side of the chassis, then the
two rear brackets positioned with just enough space to accommodate the width of
the rack. Finish by sliding the chassis into the rack and tightening the brackets
to the rack.
Figure 2-4.
Installing the Server into a Telco Rack
2-7
SUPERSERVER 6014H-32 User's Manual
2-5
Checking the Serverboard Setup
After you install the 6014H-32 in the rack, you will need to open the unit to make
sure the serverboard is properly installed and all the connections have been
made.
1. Accessing the inside of the 6014H-32 (see Figure 2-5)
First, release the retention screws that secure the unit to the rack. Grasp the two
handles on either side and pull the unit straight out until it locks (you will hear
a "click"). Next, depress the two buttons on the top of the chassis to release
the top cover. There is a large rectangular recess in the middle front of the top
cover to help you push the cover away from you until it stops. You can then lift
the top cover from the chassis to gain full access to the inside of the server.
2. Check the CPUs (processors)
You should have one or two processors already installed into the serverboard.
Each processor needs its own heatsink. See Chapter 5 for instructions on processor and heatsink installation.
3. CPU Speed
The CPU speed should automatically be detected so you will not need to change
any jumpers or settings in the BIOS Setup utility.
4. Check the system memory
Your 6014H-32 server system may have come with system memory already
installed. Make sure all DIMMs are fully seated in their slots. For details on
adding system memory, refer to Chapter 5.
5. Installing add-on cards
If desired, you can install add-on cards to the system. See Chapter 5 for details
on installing PCI add-on cards.
6. Check all cable connections and airflow
Make sure all power and data cables are properly connected and not blocking
the chassis airflow. See Chapter 5 for details on cable connections.
2-8
Chapter 2: Server Installation
Figure 2-5. Accessing the Inside of the SuperServer 6014H-32
(with optional front bezel shown)
2-6
Checking the Drive Bay Setup
Next, you should check to make sure the peripheral drives and the SAS/SATA drives
have been properly installed and all connections have been made.
1. Accessing the drive bays
All drives are accessable from the front of the server. For servicing the CD-ROM
and floppy drives, you will need to remove the top chassis cover. The SAS/SATA
disk drives can be installed and removed from the front of the chassis without
removing the top chassis cover or powering down the system.
2. CD-ROM and floppy disk drives
A slim CD-ROM and a floppy drive should be preinstalled in your server. Refer
to Chapter 6 if you need to reinstall a CD-ROM and/or floppy disk drive to the
system.
3. Check the SAS/SATA disk drives
Depending upon your system's configuration, your system may have one or more
drives already installed. If you need to install SAS/SATA drives, please refer to
Chapter 6.
2-9
SUPERSERVER 6014H-32 User's Manual
4. Check the airflow
Airflow is provided by two heavy duty 10-cm blower fans. The system component layout was carefully designed to direct the airflow to the components that
generate the most heat. Note that all power and data cables have been routed
in such a way that they do not block the airflow generated by the fans.
5. Supplying power to the system
The last thing you must do is to provide power to the system. Plug the power
cord from the power supply module into a high-quality power strip that offers
protection from electrical noise and power surges. It is recommended that you
use an uninterruptible power supply (UPS). Finish by depressing the power
button on the front of the chassis to start the system.
2-10
Chapter 3: System Interface
Chapter 3
System Interface
3-1
Overview
There are several LEDs on the control panel as well as others on the SAS/SATA
drive carriers to keep you constantly informed of the overall status of the system
as well as the activity and health of specific components. There are also two buttons on the chassis control panel and an on/off switch on the power supply. This
chapter explains the meanings of all LED indicators and the appropriate response
you may need to take.
3-2
Control Panel Buttons
There are two push-buttons located on the front of the chassis. These are (in
order from left to right) a reset button and a power on/off button.
Reset: Use the reset button to reboot the system.
Power: The main power button is used to apply or remove power from the
power supply to the server system. Turning off system power with this button
removes the main power but keeps standby power supplied to the system.
3-1
SUPERSERVER 6014H-32 User's Manual
3-3
Control Panel LEDs
The control panel located on the front of the SC813T-500 chassis has five LEDs.
These LEDs provide you with critical information related to different parts of the
system. This section explains what each LED indicates when illuminated and any
corrective action you may need to take.
Overheat/Fan Fail: When this LED flashes it indicates a fan failure. When
on continuously (on and not flashing) it indicates an overheat condition, which
may be caused by cables obstructing the airflow in the system or the ambient
room temperature being too warm. Check the routing of the cables and make
sure all fans are present and operating normally. You should also check to make
sure that the chassis covers are installed. Finally, verify that the heatsinks are
installed properly (see Chapter 5). This LED will remain flashing or on as long as
the overheat condition exists.
2
NIC2: Indicates network activity on GLAN2 when flashing .
1
NIC1: Indicates network activity on GLAN1 when flashing.
3-2
Chapter 3: System Interface
HDD: Indicates IDE channel activity. On the SuperServer 6014H-32 this
light indicates SAS/SATA and/or CD-ROM drive activity when flashing.
Power: Indicates power is being supplied to the system's power supply
units. This LED should normally be illuminated when the system is operating.
3-4
SAS/SATA Drive Carrier LED
Each SAS/SATA drive carrier has a green LED. When illuminated, this green
LED (on the front of the drive carrier) indicates drive activity. A connection to
the backplane enables this LED to blink on and off when that particular drive is
being accessed.
Note: The second LED on the SAS/SATA carriers is not used.
3-3
SUPERSERVER 6014H-32 User's Manual
Notes
3-4
Chapter 4: System Safety
Chapter 4
System Safety
4-1
Electrical Safety Precautions
!
Basic electrical safety precautions should be followed to protect yourself from
harm and the SuperServer 6014H-32 from damage:
Be aware of the locations of the power on/off switch on the chassis as well as
the room's emergency power-off switch, disconnection switch or electrical
outlet. If an electrical accident occurs, you can then quickly remove power
from the system.
Do not work alone when working with high voltage components.
Power should always be disconnected from the system when removing or
installing main system components, such as the serverboard, memory
modules and the CD-ROM and floppy drives (not necessary for SAS/SATA
drives). When disconnecting power, you should first power down the system
with the operating system and then unplug the power cords from all the power
supply modules in the system.
When working around exposed electrical circuits, another person who is
familiar with the power-off controls should be nearby to switch off the power
if necessary.
Use only one hand when working with powered-on electrical equipment. This
is to avoid making a complete circuit, which will cause electrical shock.
Use extreme caution when using metal tools, which can easily damage any
electrical components or circuit boards they come into contact with.
Do not use mats designed to decrease electrostatic discharge as protection
from electrical shock. Instead, use rubber mats that have been specifically
designed as electrical insulators.
The power supply power cord must include a grounding plug and must be
plugged into grounded electrical outlets.
4-1
SUPERSERVER 6014H-32 User's Manual
Serverboard Battery: CAUTION - There is a danger of explosion if the onboard
battery is installed upside down, which will reverse its polarities (see Figure
4-1). This battery must be replaced only with the same or an equivalent type
recommended by the manufacturer. Dispose of used batteries according to
the manufacturer's instructions.
CD-ROM Laser: CAUTION - this server may have come equipped with a CDROM drive. To prevent direct exposure to the laser beam and hazardous
radiation exposure, do not open the enclosure or use the unit in any
unconventional way.
Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Temperature Coefficient) fuses on the mainboard must be replaced by trained service
technicians only. The new fuse must be the same or equivalent as the one
replaced. Contact technical support for details and support.
4-2
General Safety Precautions
!
Follow these rules to ensure general safety:
Keep the area around the SuperServer 6014H-32 clean and free of clutter.
The SuperServer 6014H-32 weighs approximately 38 lbs (17.3 kg) when fully
loaded. When lifting the system, two people at either end should lift slowly
with their feet spread out to distribute the weight. Always keep your back
straight and lift with your legs.
Place the chassis top cover and any system components that have been
removed away from the system or on a table so that they won't accidentally
be stepped on.
While working on the system, do not wear loose clothing such as neckties and
unbuttoned shirt sleeves, which can come into contact with electrical circuits
or be pulled into a cooling fan.
Remove any jewelry or metal objects from your body, which are excellent metal
conductors that can create short circuits and harm you if they come into
contact with printed circuit boards or areas where power is present.
4-2
Chapter 4: System Safety
After accessing the inside of the system, close the system back up and secure
it to the rack unit with the retention screws after ensuring that all connections
have been made.
4-3
ESD Precautions
!
Electrostatic discharge (ESD) is generated by two objects with different electrical
charges coming into contact with each other. An electrical discharge is created to
neutralize this difference, which can damage electronic components and printed
circuit boards. The following measures are generally sufficient to neutralize this
difference before contact is made to protect your equipment from ESD:
Use a grounded wrist strap designed to prevent static discharge.
Keep all components and printed circuit boards (PCBs) in their antistatic
bags until ready for use.
Touch a grounded metal object before removing any board from its antistatic
bag.
Do not let components or PCBs come into contact with your clothing, which
may retain a charge even if you are wearing a wrist strap.
Handle a board by its edges only; do not touch its components, peripheral
chips, memory modules or contacts.
When handling chips or modules, avoid touching their pins.
Put the serverboard and peripherals back into their antistatic bags when
not in use.
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
4-3
SUPERSERVER 6014H-32 User's Manual
4-4
Operating Precautions
!
Care must be taken to assure that the chassis cover is in place when the
6014H-32 is operating to ensure proper cooling. Out of warranty damage to
the 6014H-32 system can occur if this practice is not strictly followed.
Figure 4-1. Installing the Onboard Battery
LITHIUM BATTERY
LITHIUM BATTERY
OR
BATTERY HOLDER
BATTERY HOLDER
4-4
Chapter 5: Advanced Serverboard Setup
Chapter 5
Advanced Serverboard Setup
This chapter covers the steps required to install processors and heatsinks to the
X6DHR-3G2 serverboard, connect the data and power cables and install add-on
cards. All serverboard jumpers and connections are described and a layout and
quick reference chart are included in this chapter. Remember to close the chassis completely when you have finished working on the serverboard to protect and
cool the system sufficiently.
5-1
Handling the Serverboard
Static electrical discharge can damage electronic components. To prevent damage to printed circuit boards, it is important to handle them very carefully (see
Chapter 4). Also note that the size and weight of the serverboard can cause
it to bend if handled improperly, which may result in damage. To prevent the
serverboard from bending, keep one hand under the center of the board to support it when handling. The following measures are generally sufficient to protect
your equipment from static discharge.
Precautions
•
Use a grounded wrist strap designed to prevent static discharge.
•
Touch a grounded metal object before removing any board from its antistatic
bag.
•
Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
•
When handling chips or modules, avoid touching their pins.
•
Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.
Unpacking
The serverboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.
5-1
SUPERSERVER 6014H-32 User’s Manual
5-2
Processor and Heatsink Installation
!
When handling the processor package, avoid placing direct pressure
on the label area of the fan. Also, do not place the serverboard on a
conductive surface, which can damage the BIOS battery and prevent
the system from booting up.
IMPORTANT: Always connect the power cord last and always remove it before
adding, removing or changing any hardware components. Make sure that you
install the processor into the CPU socket before you install the (optional) heatsink.
The X6DHR-3G2 can support either one or two Xeon 604-pin processors. If
installing one processor only, install it into CPU socket #1.
1. Lift the lever on the CPU socket. Lift
the lever completely or you will damage the CPU socket when power is
applied. (Install a processor into CPU
#1 socket first.)
2. Install the CPU in the socket. Make
sure that pin 1 of the CPU is seated on
pin 1 of the socket (both corners are
marked with a triangle). When using
only one CPU, install it into CPU socket
#1 (CPU socket #2 is automatically disabled if only one CPU is used).
3. Press the lever down until you hear
it *click* into the locked position. See
Figure 5-1 for pictures of the 604-pin
CPU socket before and after the processor is installed.
Socket lever
Pin 1
Socket lever in
locked position
4. To install the heatsink (optional), do not apply any thermal compound to the
heatsink or CPU die - the proper amount has already been applied. Place the
heatsink directly on the CPU so that the four mounting holes are aligned with
those on the retention mechanism. Make sure the heatsink sits completely flat on
the CPU - if not completely flat, the space between the two will degrade the heat
dissipation function of the heatsink, which may cause the processor to overheat.
5-2
Chapter 5: Advanced Serverboard Setup
5. Screw in two diagonal screws until just snug (eg. screws #1 and #2 in Figure 5-2
- do not fully tighten), then do the same with the remaining two diagonal screws.
Finish by fully tightening all four screws (see Figure 5-2).
6. If installing two processors, repeat these steps to install the second processor
in the CPU #2 slot.
Figure 5-1. 604-pin PGA Socket: Empty and with Processor Installed
Warning!
!
Make sure you lift the lever completely when installing
the CPU. If the lever is only partly raised, damage to the socket or
CPU may result.
Figure 5-2. Heatsink Installation (heatsinks are optional)
5-3
SUPERSERVER 6014H-32 User’s Manual
5-3
Connecting Cables
Now that the processors are installed, the next step is to connect the cables to
the serverboard. These include the data (ribbon) cables for the peripherals and
control panel and the power cables.
Connecting Data Cables
The ribbon cables used to transfer data from the peripheral devices have been
carefully routed in preconfigured systems to prevent them from blocking the flow
of cooling air that moves through the system from front to back. If you need to
disconnect any of these cables, you should take care to reroute them as they were
originally after reconnecting them (make sure the red wires connect to the pin 1
locations). If you are configuring the system, keep the airflow in mind when routing
the cables. The following peripheral data cables (with their connector locations
noted) should be connected. See the serverboard layout diagram in this chapter
for connector locations.
Floppy Drive cable (J12)
(Floppy power cable to J9 on SATA backplane)
CD-ROM Drive cable (J5)
(CD-ROM power cable to J10 on SATA backplane)
SAS cables (JSM1)
Control Panel cable (JF1, see next page)
Connecting Power Cables
The X6DHR-3G2 has a 20-pin primary power supply connector designated "J3"
for connection to the ATX power supply. Connect the appropriate connector from
the power supply to J3 to supply power to the serverboard. See the Connector
Definitions section in this chapter for power connector pin definitions.
In addition, your power supply must be connected to the 4-pin Secondary ATX
Power connection at J38 and the 8-pin processor power connector at J1D1.
5-4
Chapter 5: Advanced Serverboard Setup
Connecting the Control Panel
JF1 contains header pins for various front control panel connectors. See Figure
5-3 for the pin locations of the various front control panel buttons and LED indicators. Please note that even and odd numbered pins are on opposite sides of
each header.
All JF1 wires have been bundled into single keyed ribbon cable to simplify their
connection. The red wire in the ribbon cable plugs into pin 1 of JF1. Connect
the other end of the cable to the Control Panel printed circuit board, located just
behind the system status LEDs in the chassis.
See the Connector Definitions section in this chapter for details and pin descriptions of JF1.
Figure 5-3. Front Control Panel Header Pins (JF1)
20
19
Ground
NMI
x (key)
x (key)
Power LED
Vcc
HDD LED
Vcc
NIC1
Vcc
NIC2
Vcc
OH/Fan Fail LED
Vcc
Power Fail LED
Vcc
Ground
Reset
Ground
Power
2
5-5
1
SUPERSERVER 6014H-32 User’s Manual
5-4
I/O Ports
The I/O ports are color coded in conformance with the PC 99 specification. See
Figure 5-4 below for the colors and locations of the various I/O ports.
Figure 5-4. Rear Panel I/O Ports
SAS
5-5
Installing Memory
Note: Check the Supermicro web site for recommended memory modules.
CAUTION
Exercise extreme care when installing or removing DIMM modules
to prevent any possible damage. Also note that the memory is interleaved to improve performance (see step 1).
DIMM Installation (See Figure 5-5)
1. Insert the desired number of DIMMs into the memory slots, starting with Bank
1 (both DIMM#1A and DIMM#1B). The memory scheme is interleaved so
you must install two modules at a time, beginning with Bank 0, then Bank
1 and so on.
2. Insert each DIMM module vertically into its slot. Pay attention to the notch
along the bottom of the module to prevent inserting the DIMM module incorrectly.
3. Gently press down on the DIMM module until it snaps into place in the slot.
Repeat for all modules (see step 1 above).
5-6
Chapter 5: Advanced Serverboard Setup
Memory Support
The X6DHR-3G2 supports up to 16 GB of registered ECC DDR2-400 SDRAM.
You should not mix DIMMs of different sizes and speeds. See Figure 5-5 for
installing and removing memory modules.
Figure 5-5a. Installing DIMM into Slot
Notch
Release
Tab
Notch
Note: Notches
should align
with their
receptive points
on the slot
Release
Tab
To Install: Insert module vertically and press down until it snaps into place. Pay attention to the bottom
notches.
To Remove: Use your thumbs to gently push each release tab outward to free the DIMM from the
slot.
Figure 5-5b. Top View of DDR Slot
5-7
SUPERSERVER 6014H-32 User’s Manual
5-6
Adding PCI Cards
1. PCI slots
The 6014H-32 can accommodate add-on cards in both the PCI-X 133 MHz and
the PCI-X 100 MHz slot with the use of two riser cards, which are included with
the system: the CSE-RR1U-X riser supports a standard size card in slot #6 and the
CSE-RR1U-XLP riser supports a low profile card in slot #7).
An additional two riser cards are available as an option to support add-on cards
in the SXB-E1 and SXB-E2 x8 (PCI-Express) slots: the CSE-RR1U-EL riser (for
a standard size card) and the CSE-RR1U-ELP (for a low profile card).
2. PCI card installation
Before installing a PCI add-on card, make sure you install it into the correct riser
card. Begin by releasing the locking tab that corresponds to the slot you wish to
populate. Insert the expansion card into the correct riser card, pushing down with
your thumbs evenly on both sides of the card.
5-8
Chapter 5: Advanced Serverboard Setup
5-7
Serverboard Details
Figure 5-6. SUPER X6DHR-3G2 Layout
(not drawn to scale)
J 3 8 J1D1
J32
J33
J43
DIMM 1A
Bank1
DIMM 1B
J34
JAR
J3P
DIMM 2A
USB 0/1
Bank2
DIMM 2B
CPU1
DIMM 3A
DIMM 3B
COM1
JP9
Bank3
DIMM 4A
FAN1
Bank4
DIMM 4B
JF1
FAN2
GLAN
Controller
E7520
VGA
BIOS
SuperIO
JSM2
ICH5R
SPKR
SAS/SATA
Controller
9410W
South
Bridge
RAGE
XL
DS5/6/7/8
JBT1
USB2/3
COM2
Note:
Jumpers not noted are for test purposes only.
5-9
DS1/2/3/4
JSM1
J31
Battery
JPL1 J11
JPG1
JPS1
PXH
IDE #1
ZCR
IDE #2
JP17
JP18
IPMI
JOH/JL1/JD1/JWOL
JWD
FAN3
JLAN2
FAN4
SXB-E1 x8
J6 J5
J12
JWF1
JWF2
Floppy
SXB-E2 x8
Slot 6: PCI-X 133 MHz
JS10
JWOR
Slot 7: PCI-X 100 MHz
JLAN1
FAN5
I-SATA1
I-SATA0
CPU2
North Bridge
SUPERSERVER 6014H-32 User’s Manual
X6DHR-3G2 Quick Reference
Jumper
Description
Default Setting
J3P
3rd Power Supply Detect
Open (Disabled)
JBT1
CMOS Clear
See Jumper Section
JP17/JP18
JPG1
Compact Flash Master/Slave Select
VGA Enable/Disable
Pins 1-2 (Master)
Pins 1-2 (Enabled)
JPL1
JLAN Enable/Disable
Pins 1-2 (Enabled)
JPS1
SAS Enable/Disable
Pins 1-2 (Enabled)
JWD
Watchdog
Pins 1-2 (Reset)
Connector
Description
COM1/COM2
FAN1-5
IPMI
J1D1
J5/J6
J11
J12
J32
J33/J34
J38
J43
JAR
JD1
JF1
JL1
JLAN1/2
JOH1
COM1/COM2 Serial Port/Header
System Fan Headers
IPMI 2.0 Socket
Processor Power Connector
IDE #1/#2 Connectors (both can support CF cards)
SMB (System Management Bus) Header
Floppy Disk Drive Connector
SMB (System Management Bus) Power Header
Keyboard/Mouse Ports
Secondary (12V) ATX Power Connector
Primary 20-pin ATX Power Connector
Alarm Rest Header
Power LED/Speaker Header
Front Control Panel Connector
Chassis Intrusion Header
Gigabit Ethernet Ports
Overheat LED Header
JP9
JS9
JS10
Power Supply Fail Header
SAS (to IO Panel) Activity LED Header
SAS I2C Header
JSM1/JSM2
JWF1/JWF2
JWOL
JWOR
SATA0/1
USB0/1
USB2/3
SAS Ports (JSM1 = SAS0-3, JSM2 = SAS4-7)
Compact Flash Card PWR (*Note 2)
Wake-on-LAN Header
Wake-on-Ring Header
6300ESB Serial ATA Connectors
Universal Serial Bus Ports
Universal Serial Bus Headers
Indicators
Description
DS1-DS8
SAS Activity LEDs
5-10
Chapter 5: Advanced Serverboard Setup
5-8
Connector Definitions
ATX Power 20-pin Connector
Pin Definitions (J43)
Pin#
Definition
11
+3.3V
1
+3.3V
The power supply connector meets
12
-12V
2
+3.3V
the SSI (Superset ATX) 20-pin specifi-
13
COM
3
COM
cation. Make sure that the orientation
of the connector is correct. See the
14
PS_ON
4
+5V
15
COM
5
COM
table on the right for pin definitions.
16
COM
6
+5V
17
COM
7
COM
18
-5V
8
PWR_OK
19
+5V
9
5V Standby
20
+5V
10
+12V
ATX Power Connection
Pin #
Definition
PWR_SEC Connection
In addition to the Primary ATX power
connector (above), the Secondary
12v 8-pin J15 connector (J38) must
also be connected to your power supply. See the table on the right for pin
definitions.
Processor Power Connector
The header at J1D1 must also be connected to the power supply to provide
power for the processor(s). See the
+12V 4-pin Power
Pin Definitions (J38)
Pins
Definition
1&2
Ground
3&4
+12V
Processor Power
Pin Definitions (J1D1)
Pins
Definition
1 through 4
Ground
5 through 8
+12V
table on the right for pin definitions.
NMI Button
NMI Button
Pin Definitions (JF1)
The non-maskable interrupt button
header is located on pins 19 and 20
of JF1. Refer to the table on the right
for pin definitions.
Power LED
Pin#
Definition
19
Control
20
Ground
Power LED
Pin Definitions (JF1)
The Power LED connection is located
on pins 15 and 16 of JF1. Refer to the
table on the right for pin definitions.
5-11
Pin#
Definition
15
Vcc
16
Control
SUPERSERVER 6014H-32 User’s Manual
HDD LED
HDD LED
Pin Definitions (JF1)
The HDD (IDE Hard Disk Drive) LED
Pin#
Definition
connection is located on pins 13 and
13
Vcc
14 of JF1. Attach the IDE hard drive
LED cable to display disk activity.
14
HD Active
Refer to the table on the right for pin
definitions.
NIC1 LED
NIC1 LED
Pin Definitions (JF1)
The NIC1 (Network Interface Control-
Pin#
Definition
ler) LED connection is located on pins
11 and 12 of JF1. Attach the NIC1
LED cable to display network activity.
Refer to the table on the right for pin
definitions.
11
Vcc
12
Ground
NIC2 LED
NIC2 LED
Pin Definitions (JF1)
The NIC2 (Network Interface Controller) LED connection is located on pins
9 and 10 of JF1. Attach the NIC2
LED cable to display network activity.
Refer to the table on the right for pin
definitions.
Overheat/Fan Fail LED (OH)
Connect an LED to the OH connection
on pins 7 and 8 of JF1 to provide advanced warning of chassis overheating. Refer to the table on the right for
pin definitions.
Power Fail LED
Pin#
Definition
9
Vcc
10
Ground
OH/Fan Fail LED
Pin Definitions (JF1)
Pin#
Definition
7
Vcc
8
Ground
Power Fail LED
Pin Definitions (JF1)
The Power Fail LED connection is
located on pins 5 and 6 of JF1. Refer
to the table on the right for pin definitions. This only applies to systems
with redundant power supplies (not
the 6014H-32).
5-12
Pin#
Definition
5
Vcc
6
Ground
Chapter 5: Advanced Serverboard Setup
Reset Button
Reset Button
Pin Definitions (JF1)
The Reset Button connection is located on pins 3 and 4 of JF1. Attach
Pin#
Definition
it to the hardware reset switch on the
computer case. Refer to the table on
3
Reset
4
Ground
the right for pin definitions.
Power Button
Power Button
Pin Definitions (JF1)
The Power Button connection is
located on pins 1 and 2 of JF1. Momentarily contacting both pins will
power on/off the system. This button
can also be configured to function
as a suspend button (see the Power
Button Mode setting in BIOS). To turn
off the power when set to suspend
mode, depress the button for at least
4 seconds. Refer to the table on the
right for pin definitions.
Universal Serial Bus
(USB0/1)
Pin#
Definition
1
PW_ON
2
Ground
Universal Serial Bus
Pin Definitions (USB0/1)
Two Universal Serial Bus ports are
located beside the PS/2 keyboard/
mouse ports. USB0 is the bottom
connector and USB1 is the top connector. See the table on the right for
pin definitions.
Chassis Intrusion
USB0
Pin #
Definition
USB1
Pin #
Definition
1
+5V
1
+5V
2
PO-
2
PO-
3
PO+
3
PO+
4
Ground
4
Ground
5
N/A
5
Key
Chassis Intrusion
Pin Definitions (JL1)
The Chassis Intrusion header is designated at JL1. Attach the appropriate cable to inform you of a chassis
intrusion.
5-13
Pin#
Definition
1
Intrusion Input
2
Ground
SUPERSERVER 6014H-32 User’s Manual
Serial Ports
Serial Port Pin Definitions
(COM1/COM2)
The COM1 serial port is located beside
Pin #
Definition
Pin #
Definition
the mouse port. COM2 is a header on
1
DCD
6
DSR
the serverboard (see serverboard
layout for location). See the table on
2
RXD
7
RTS
3
TXD
8
CTS
the right for pin definitions.
4
DTR
9
RI
5
Ground
10
NC
Note: Pin 10 is included on the header but not on
the port. NC indicates no connection.
Power Supply Fail Header
Power Fail Header
Pin Definitions (JP9)
Connect a cable from your power supply to the Power Fail header to provide
you with warning of a power supply
failure. The warning signal is passed
through the PWR_LED pin to indicate
a power failure. See the table on the
right for pin definitions.
Pin#
Definition
1
P/S 1 Fail Signal
2
P/S 2 Fail Signal
3
P/S 3 Fail Signal
4
Reset (from MB)
Fan Headers
Fan Header
Pin Definitions
(Fan1-5)
The X6DHR-3G2 has five fan headers, designated Fan1 through Fan5.
Fan speed is controlled via Thermal
Management with a BIOS setting.
See the table on the right for pin
definitions.
Overheat LED
Pin#
Definition
1
Ground (Black)
2
+12V (Red)
3
Tachometer
Overheat LED
Pin Definitions (JOH1)
Connect an LED to the JOH1 header
to provide warning of a chassis overheating condition. See the table on the
right for pin definitions.
5-14
Pin#
Definition
1
+5V
2
OH Active
Chapter 5: Advanced Serverboard Setup
Extra Universal Serial Bus
Headers
Front Panel Universal Serial Bus
Pin Definitions (USB2/3)
Two additional USB headers (USB2/3)
are located near the WWD jumper on
the serverboard. These are included
for connection to the ports on the
front of the chassis. A USB cable
(not included) is needed for the con-
USB2
Pin #
Definition
USB3
Pin #
Definition
1
+5V
1
+5V
2
PO-
2
PO-
3
PO+
3
PO+
4
Ground
4
Ground
5
N/A
5
N/A
nection. See the table on the right for
pin definitions.
Power LED/Speaker
Speaker Connector
Pin Definitions (JD1)
On the JDI header, pins 1-3 are for
a power LED, pins 4-7 are for the
speaker. See the table on the right
for speaker pin definitions. Note:
The speaker connector pins are for
use with an external speaker. If you
wish to use the onboard speaker, you
should close pins 6-7 with a jumper.
Pin #
Function
Definition
4
+
Speaker data (red wire)
5
Key
No connection
6
Key
7
Speaker data
ATX PS/2 Keyboard and
PS/2 Mouse Ports
PS/2 Keyboard and
Mouse Port Pin
Definitions (J33, J34)
The ATX PS/2 keyboard and the PS/2
mouse ports are located at J33 and
J34, respectively. See the table on
the right for pin definitions.
JLAN1/2 (Ethernet Ports)
Two Ethernet ports (designated JLAN1
and JLAN2) are located beside the
VGA port on the I/O backplane. These
ports accept RJ45 type cables.
5-15
Pin#
Definition
1
Data
2
NC
3
Ground
4
VCC
5
Clock
6
NC
SUPERSERVER 6014H-32 User’s Manual
Wake-On-LAN
Wake-On-LAN
Pin Definitions (WOL)
The Wake-On-LAN header is desig-
Pin#
Definition
nated WOL. See the table on the right
1
+5V Standby
for pin definitions. You must enable
the LAN Wake-Up setting in BIOS to
2
Ground
3
Wake-up
use this feature. You must also have
a LAN card with a Wake-on-LAN connector and cable.
Wake-On-Ring
Wake-On-Ring
Pin Definitions
(JWOR)
The Wake-On-Ring header is designated JWOR. This function allows
your computer to receive and "wakeup" by an incoming call to the modem
when in suspend state. See the table
on the right for pin definitions. You
must have a WOR card and cable to
use this feature.
Pin#
Definition
1
Ground (Black)
2
Wake-up
SMB
SMB Header
Pin Definitions (J11)
The System Management Bus header
(for the PCI bus) designated J11 is
located near the battery. Connect the
appropriate cable here to utilize SMB
on your system. See the table on the
right for pin definitions.
Pin#
Definition
1
Data
2
Ground
3
Clock
4
No Connection
SMB Power (I2C)
Pin Definitions (J32)
SMB Power (I2C)
The header at J32 is for SMB, which
may be used to monitor the status of
the power supply. See the table on the
right for pin definitions.
5-16
Pin#
Definition
1
Clock
2
SMB Data
3
N/A
4
N/A
5
N/A
Chapter 5: Advanced Serverboard Setup
5-9
Jumper Settings
Explanation of
Jumpers
To modify the operation of the
serverboard, jumpers can be used to
3
2
1
3
2
1
Connector
Pins
choose between optional settings.
Jumpers create shorts between two
Jumper
pins to change the function of the
connector. Pin 1 is identified with
a square solder pad on the printed
Setting
circuit board. See the diagram at
right for an example of jumping pins
1 and 2. Refer to the serverboard
layout page for jumper locations.
Note 1: On t wo - pin jumpers,
"Closed" means the jumper is on
and "Open" means the jumper is
off the pins.
CMOS Clear
JBT1 is used to clear CMOS and will also clear any passwords. Instead of pins,
this jumper consists of contact pads to prevent accidentally clearing the contents
of CMOS.
To clear CMOS,
1) First power down the system and unplug the power cord(s)
2) With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver
3) Remove the screwdriver (or shorting device)
4) Reconnect the power cord(s) and power on the system.
Note: Do not use the PW_ON connector to clear CMOS.
VGA Enable/Disable
VGA Enable/Disable
Jumper Settings (JPG1)
JPG1 allows you to enable or disable
the VGA port. The default position is
on pins 1 and 2 to enable VGA. See
the table on the right for jumper settings.
5-17
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
SUPERSERVER 6014H-32 User’s Manual
JLAN Enable/Disable
JLAN Enable/Disable
Jumper Settings (JPL1)
Change the setting of jumper JPL1
Jumper Setting
to enable or disable the JLAN1 and
Pins 1-2
Enabled
JLAN2 Ethernet ports. See the table
on the right for jumper settings. The
Pins 2-3
Disabled
Definition
default setting is enabled
3rd Power Supply Fail Detect
Enable/Disable
The system can notify you in the event
of a power supply failure. This feature
assumes that three power supply units
are installed in the chassis with one
acting as a backup. If you only have
one or two power supply units installed,
you should disable this (the default setting) with J3P to prevent false alarms.
3rd Power Supply Fail
Detect Enable/Disable
Jumper Settings (J3P)
Jumper Setting
Definition
Open*
Disabled
Closed
Enabled
Note: This feature is only available when using
redundant Supermicro power supplies.
Alarm Reset (JAR)
The system will notify you in the event
of a power supply failure. This feature
assumes that Supermicro redundant
power supply units are installed in the
chassis. If you only have a single power
supply installed, you should not connect
anything to this jumper to prevent false
alarms. See the table on the right for
jumper settings.
5-18
Alarm Reset
Jumper Settings (JAR)
Pin#
Definition
2
+5V
1
Ground
Chapter 5: Advanced Serverboard Setup
Watch Dog Enable/Disable
JWD controls the Watch Dog function.
Watch Dog is a system monitor that
Watch Dog
Jumper Settings (JWD)
can reboot the system when a software
application hangs. Pins 1-2 will cause
Jumper Setting
Definition
Pins 1-2
Reset
WD to reset the system if an applica-
Pins 2-3
NMI
tion hangs. Pins 2-3 will generate a
Open
Disabled
non-maskable interrupt signal for the
application that is hung up. See the
table on the right for jumper settings.
Watch Dog must also be enabled in
BIOS. Note: When enabled, the user
needs to write their own application
software in order to disable the Watch
Dog Timer.
Compact Flash Master/Slave
If you wish to use a Compact Flash
card in the IDE slot(s), you must assign
master or slave status to the slot(s) being used. JP17 assigns status to the
IDE#1 slot and JP18 assigns status to
the IDE#2 slot. See the table on the
right for jumper settings.
SAS Controller Enable
JPS1 enables or disables the Adaptec 9140W SAS controller on the
serverboard. See the table on the
right for jumper settings. The default
setting is enabled.
5-19
Compact Flash Master/Slave
Jumper Settings (JP17/JP18)
Jumper Setting
Definition
Open
Slave
Closed
Master
SAS Controller Enable
Jumper Settings (JPS1)
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
SUPERSERVER 6014H-32 User’s Manual
5-10 Onboard Indicators
JLAN Left LED
(Connection Speed Indicator)
JLAN1/JLAN2 LEDs
LED Color
Definition
Off
10 MHz
The Ethernet ports (located beside
Green
100 MHz
the VGA port) have two LEDs.
Amber
1 GHz
On
each Gigabit LAN port, the yellow
(right) LED indicates activity while the
left LED may be green, orange or off
to indicate the speed of the connection.
See the table on the right for
the functions associated with the left
(connection speed) LED.
SAS Activity LED Indicators
The SAS Activity LED indicators
(DS1-DS8) indicate the activity status
of SAS ports (0-7). See the table on
the right for pin definitions.
5-20
SAS Activity LED Indicators
(DS9-DS16)
DS# Definition
DS# Definition
DS1
SAS0:Act
DS5
SAS4:Act
DS2
SAS1:Act
DS6
SAS5:Act
DS3
SAS2:Act
DS7
SAS6:Act
DS4
SAS3:Act
DS8
SAS7:Act
Chapter 5: Advanced Serverboard Setup
5-11 SATA, Floppy and Hard Drive Connections
Note the following when connecting the floppy and hard disk drive cables:
•
The floppy disk drive cable has seven twisted wires.
•
A red mark on a wire typically designates the location of pin 1.
• A single floppy disk drive ribbon cable has 34 wires and two connectors to provide
for two floppy disk drives. The connector with twisted wires always connects to
drive A, and the connector that does not have twisted wires always connects to
drive B.
Floppy Connector
The floppy connector is designated
J12. See the table below for pin
definitions.
Floppy Drive Connector
Pin Definitions (J12)
Pin#
Definition
1
Ground
2
FDHDIN
3
Ground
4
Reserved
5
Key
6
FDEDIN
7
Ground
8
Index
9
Ground
10
Motor Enable
11
Ground
12
Drive Select B
13
Ground
14
Drive Select B
15
Ground
16
Motor Enable
17
Ground
18
DIR
19
Ground
20
STEP
21
Ground
22
Write Data
23
Ground
24
Write Gate
25
Ground
26
Track 00
27
Ground
28
Write Protect
29
Ground
30
Read Data
31
Ground
32
Side 1 Select
33
Ground
34
Diskette
5-21
Pin #
Definition
SUPERSERVER 6014H-32 User’s Manual
IDE Connectors
IDE Drive Connectors
Pin Definitions (J5/J6)
See the table on the right for
Pin#
Definition
pin definitions for the onboard
1
Reset IDE
2
Ground
IDE#1 and #2 connectors.
3
Host Data 7
4
Host Data 8
5
Host Data 6
6
Host Data 9
7
Host Data 5
8
Host Data 10
9
Host Data 4
10
Host Data 11
11
Host Data 3
12
Host Data 12
13
Host Data 2
14
Host Data 13
15
Host Data 1
16
Host Data 14
17
Host Data 0
18
Host Data 15
19
Ground
20
Key
21
DRQ3
22
Ground
23
I/O Write
24
Ground
25
I/O Read
26
Ground
27
IOCHRDY
28
BALE
29
DACK3
30
Ground
31
IRQ14
32
IOCS16
33
Addr1
34
Ground
35
Addr0
36
Addr2
37
Chip Select 0
38
Chip Select 1
39
Activity
40
Ground
SATA Connectors
Pin #
Definition
SATA Connector Pin Definitions
(JSM1/JSM2)
See the table on the right for
pin definitions for the onboard
SATA connectors.
5-22
Pin #
Definition
1
Ground
2
TXP
3
TXN
4
Ground
5
RXN
6
RXP
7
Ground
Chapter 6: Advanced Chassis Setup
Chapter 6
Advanced Chassis Setup
This chapter covers the steps required to install components and perform maintenance on the SC813T-500 chassis. For component installation, follow the steps
in the order given to eliminate the most common problems encountered. If some
steps are unnecessary, skip ahead to the next step.
Tools Required
The only tool you will need to install components and perform maintenance is a
Philips screwdriver.
6-1
Static-Sensitive Devices
Electrostatic discharge (ESD) can damage electronic components. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully. The following measures are generally sufficient to protect your equipment
from ESD damage.
Precautions
Use a grounded wrist strap designed to prevent static discharge.
Touch a grounded metal object before removing any board from its antistatic
bag.
Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
When handling chips or modules, avoid touching their pins.
Put the serverboard, add-on cards and peripherals back into their antistatic bags
when not in use.
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
6-1
SUPERSERVER 6014H-32 User's Manual
Figure 6-1. Chassis: Front and Rear Views
Slim CD-ROM Drive
Slim Floppy Drive
SAS/SATA Drive Bays
Power Supply Module
Mouse/Keyboard
6-2
USB Ports
COM1 Port
System LEDs
System Reset
Control Panel
Main Power
PCI Expansion Slots (w/ riser cards)
Ethernet Ports
VGA Port
Ext. SATA Port
Control Panel
The control panel (located on the front of the chassis) must be connected to the
JF1 connector on the serverboard to provide you with system status indications.
These wires have been bundled together as a ribbon cable to simplify the connection. Connect the cable from JF1 on the serverboard to the appropriate header on
the Control Panel PCB (printed circuit board). Make sure the red wire plugs into
pin 1 on both connectors. Pull all excess cabling out of the airflow path.
The control panel LEDs inform you of system status. See "Chapter 3: System
Interface" for details on the LEDs and the control panel buttons. Details on JF1
can be found in "Chapter 5: Advanced Serverboard Setup."
6-2
Chapter 6: Advanced Chassis Setup
6-3
System Fans
Two 10-cm blower fans provide all the cooling needed for the SuperServer 6014H32. It is very important that the chassis top cover is properly installed and making
a good seal in order for the cooling air to circulate properly through the chassis and
cool the components. See Figure 6-2.
System Fan Failure
Fan speed is controlled by system temperature via a BIOS setting. If a fan fails,
the remaining fan will ramp up to full speed and the overheat/fan fail LED on the
control panel will turn on. Replace any failed fan at your earliest convenience
with the same type and model (the system can continue to run with a failed fan).
Remove the top chassis cover (see instructions on p. 2-8) while the system is
still running to determine which of the two fans has failed. Then power down the
system before replacing a fan. Removing the power cord(s) is also recommended
as a safety precaution.
Replacing System Cooling Fans
1. Removing a fan
After turning off the power to the system, first remove the chassis cover and unplug
the fan cable from the motherboard. Unscrew the failed blower fan from the chassis
and pull it completely out from the serverboard.
2.Installing a new fan
Replace the failed fan with an identical 10-cm, 12 volt fan (available from
Supermicro: p/n FAN-0059). Install the new fan in its proper place in the chassis
by positioning it on the two mounting posts. Secure the fan to the chassis with
the screws you removed previously, then attach the fan wires to the same chassis
fan header you removed it from. Make sure the air seal under the fan is properly
installed and creating a good seal. Power up the system and check that the fan is
working properly and that the LED on the control panel has turned off. Finish by
replacing the chassis cover.
6-3
SUPERSERVER 6014H-32 User's Manual
10-cm Blower Fans
Figure 6-2. System Cooling Fans (with optional front bezel shown)
6-4
Drive Bay Installation/Removal
Removing the Front Bezel
If your system has a front bezel (optional) attached to the chassis, you must first
remove it to gain access to the drive bays. To remove the bezel, first unlock the
front of the chassis then press the release knob (see Figure 6-3). Carefully remove the bezel with both hands. A filter located within the bezel can be removed
for replacement/cleaning. It is recommended that you keep a maintenance log of
filter cleaning/replacement, since its condition will affect the airflow throughout the
whole system.
6-4
Chapter 6: Advanced Chassis Setup
Figure 6-3. Removing the Front Bezel
1. Unlock
2. Press release knob
3. Remove bezel assembly
Accessing the Drive Bays
SAS/SATA Drives: Because of their hotswap capability, you do not need to access
the inside of the chassis or power down the system to install or replace SAS/SATA
drives. Proceed to the next step for instructions.
CD-ROM/Floppy Disk Drives: For installing/removing a CD-ROM or floppy disk
drive, you will need to gain access to the inside of the 6014H-32 by removing the
top cover of the chassis. Proceed to the "CD-ROM and Floppy Drive Installation"
section later in this chapter for instructions.
Note: Only a "slim" CD-ROM drive will fit into the 6014H-32.
6-5
SUPERSERVER 6014H-32 User's Manual
SAS/SATA Drive Installation
1. Mounting a SAS/SATA drive in a drive carrier
The SAS/SATA drives are mounted in drive carriers to simplify their installation and
removal from the chassis. These carriers also help promote proper airflow for the
SAS/SATA drive bays. For this reason, even empty carriers without drives installed
must remain in the chassis. To add a new SAS/SATA drive, install a drive into the
carrier with the printed circuit board side facing down so that the mounting holes
align with those in the carrier. Secure the drive to the carrier with six screws, as
shown in Figure 6-4.
Figure 6-4. Mounting a SAS/SATA Drive in a Carrier
!
!
Use caution when working around the SAS/SATA backplane. Do
not touch the backplane with any metal objects and make sure no
ribbon cables touch the backplane or obstruct the holes, which
aid in proper airflow.
Important: Regardless of how many SAS/SATA hard drives are
installed, all drive carriers must remain in the drive bays to maintain proper airflow.
6-6
Chapter 6: Advanced Chassis Setup
2. Installing/removing hot-swap SAS/SATA drives
The SAS/SATA drive carriers are all easily accessible at the front of the chassis.
These hard drives are hot-pluggable, meaning they can be removed and installed
without powering down the system. To remove a carrier, push the release button
located beside the drive LEDs. Then swing the colored handle fully out and use it
to pull the unit straight out (see Figure 6-5).
Note: Your operating system must have RAID support to enable the hot-plug capability of the SAS/SATA drives.
Figure 6-5. Removing a SAS/SATA Drive from the Server
SAS/SATA Power Cables
SAS and SATA power cables should be routed so that they do not block the airflow
through the chassis. See the serverboard layout diagram for the location of the
cable connections.
SAS/SATA Backplane
The SAS/SATA drives plug into a backplane that provides power, drive ID and bus
termination. A RAID controller can be used with the backplane to provide data
security. The operating system you use must have RAID support to enable the
hot-swap capability of the drives. The backplane is already preconfigured, so there
are no jumpers or switches present on it.
6-7
SUPERSERVER 6014H-32 User's Manual
CD-ROM and Floppy Drive Installation
The top cover of the chassis must be opened to gain full access to the CD-ROM
and floppy drive bays. The 6014H-32 accomodates only slim-line CD-ROM drives.
Side mounting brackets are needed to mount a slim-line CD-ROM drive in the
6014H-32 server.
You must power down the system before installing or removing a floppy or CD-ROM
drive. First, release the retention screws that secure the server unit to the rack.
Grasp the two handles on either side and pull the unit straight out until it locks
(you will hear a "click"). Next, depress the two buttons on the top of the chassis
to release the top cover and at the same time, push the cover away from you until
it stops. You can then lift the top cover from the chassis to gain full access to the
inside of the server.
With the chassis cover removed, unplug the power and data cables from the drive
you want to remove. Then locate the locking tab at the rear of the drive. It will be
on the left side of the drive when viewed from the front of the chassis. Pull the tab
away from the drive and push the drive unit out the front of the chassis. Add a new
drive by following this procedure in reverse order. You may hear a faint *click* of the
locking tab when the drive is fully inserted. Remember to reconnect the data and
power cables to the drive before replacing the chassis cover and restoring power
to the system. Please be aware of the following:
•
The floppy disk drive cable has seven twisted wires.
•
A color mark on a cable typically designates the location of pin 1.
• A single floppy disk drive ribbon cable has 34 wires and two connectors to provide
for two floppy disk drives. The connector with twisted wires always connects to
drive A, and the connector that does not have twisted wires always connects to
drive B.
6-8
Chapter 6: Advanced Chassis Setup
6-5
Power Supply
The SuperServer 6014H-32 has a single 500 watt power supply, which is autoswitching capable. This enables it to automatically sense and operate at a 100v
to 240v input voltage. An amber light will be illuminated on the power supply
when the power is off. An illuminated green light indicates that the power supply
is operating.
Power Supply Failure
If the power supply unit fails, the system will shut down and you will need to replace
the unit. Replacement units can be ordered directly from Supermicro (see contact
information in the Preface). As there is only one power supply unit in the 6014H-32,
power must be completely removed from the server before removing and replacing
the power supply unit for whatever reason.
Removing/Replacing the Power Supply
1. Removing the power supply
First turn the power switch on the control panel off, then unplug the power cord
from the system. Remove the chassis cover by pressing the two release buttons
on the top of the chassis (near the front) and push the chassis top rearward about
one inch. To remove the failed power unit, push the beige colored release tab to
the right and then carefully lift the unit up about 1/2 inch only. If you lift too high,
you may damage the power distribution board that the other end of the unit is
connected to. Then, pull the power unit straight back to unplug it from the power
distribution board. See Figure 6-6.
2. Installing a new power supply
Replace the failed unit with another unit of the same input voltage, output voltage
and wattage. It is highly recommended to replace it with exactly the same model
power supply. Carefully insert the new unit into position to plug it into the power
distribution board, making sure you are not holding it at too great an angle, which
may damage the power distribution board. Push it completely into the power
distribution board and seat it in the chassis. When correctly installed it should be
laying flat - make sure the end of the power supply is not sitting on the stop in the
chassis. Reconnect the power cord, replace the chassis top cover and reposition
the unit back into the rack. Finish by depressing the power button on the chassis
front control panel.
6-9
SUPERSERVER 6014H-32 User's Manual
Figure 6-6. Removing/Replacing the Power Supply
6-10
Chapter 7: BIOS
Chapter 7
BIOS
7-1
Introduction
This chapter describes the Phoenix BIOS™ Setup utility for the X6DHR-3G2. The
Phoenix ROM BIOS is stored in a flash chip and can be easily upgraded using a
floppy disk-based program.
Note: Due to periodic changes to the BIOS, some settings may have been added or
deleted and might not yet be recorded in this manual. Please refer to Supermicro's
web site: <http://www.supermicro.com> for any changes to BIOS that may not be
reflected in this manual.
System BIOS
The BIOS is the Basic Input Output System used in all IBM® PC, XT™, AT®, and
PS/2® compatible computers. The Phoenix BIOS flash chip stores the system
parameters, such as type of disk drives, video displays, etc. in the CMOS. The
CMOS memory requires very little electrical power. When the computer is turned
off, a back-up battery provides power to the BIOS flash chip, enabling it to retain
system parameters. Whenever the computer is powered-on, the computer is configured with the values stored in the BIOS ROM by the system BIOS, which gains
control at boot-up.
How To Change the Configuration Data
The CMOS information that determines the system parameters may be changed by
entering the BIOS Setup utility. This Setup utility can be accessed by pressing the
<Delete> key at the appropriate time during system boot, see below.
Starting the Setup Utility
Normally, the only visible POST (Power On Self Test) routine is the memory test. As
the memory is being tested, press the <Delete> key to enter the main menu of the
BIOS Setup utility. From the main menu, you can access the other setup screens,
such as the Security and Power menus. Beginning with Section 7-3, detailed descriptions are given for each parameter setting in the Setup utility.
Note: fan speed is controlled by the “Fan Speed Control Mode” setting in BIOS (see
page 7-15). The recommended setting for the 6014H-32 is “3-pin (Server)”
7-1
SUPERSERVER 6014H-32 User's Manual
7-2
Running Setup
*Default settings are in bold text unless otherwise noted.
The BIOS setup options described in this section are selected by choosing
the appropriate text from the main BIOS Setup screen. All displayed text is
described in this section, although the screen display is often all you need to
understand how to set the options (see on next page).
When you first power on the computer, the Phoenix BIOS™ is immediately activated.
While the BIOS is in control, the Setup program can be activated in one of two
ways:
1.
By pressing <Delete> immediately after turning the system on, or
2. When the message shown below appears briefly at the bottom of the screen
during the POST (Power On Self-Test), press the <Delete> key to activate the
main Setup menu:
Press the <Delete> key to enter Setup
7-3
Main BIOS Setup
All main Setup options are described in this section. The main BIOS Setup screen
is displayed below.
Use the Up/Down arrow keys to move among the different settings in each menu.
Use the Left/Right arrow keys to change the options for each setting.
Press the <Esc> key to exit the CMOS Setup Menu. The next section describes in
detail how to navigate through the menus.
Items that use submenus are indicated with the icon. With the item highlighted,
press the <Enter> key to access the submenu.
7-2
Chapter 7: BIOS
Main BIOS Setup Menu
Main Setup Features
System Time
To set the system date and time, key in the correct information in the appropriate
fields. Then press the <Enter> key to save the data.
System Date
Using the arrow keys, highlight the month, day and year fields and enter the correct
data. Press the <Enter> key to save the data.
BIOS Date
This feature allows BIOS to automatically display the BIOS date.
7-3
SUPERSERVER 6014H-32 User's Manual
Legacy Diskette A
This setting allows the user to set the type of floppy disk drive installed as diskette A.
The options are Disabled, 360Kb 5.25 in, 1.2MB 5.25 in, 720Kb 3.5 in, 1.44/1.25MB,
3.5 in and 2.88MB 3.5 in.
Parallel ATA
This setting allows the user to enable or disable the function of Parallel ATA. The
options are Disabled, Channel 0, Channel 1 and Both.
Serial ATA
This setting allows the user to enable or disable the function of Serial ATA. The
options are Disabled and Enabled.
Serial ATA RAID Enable
Select Enable to enable Serial ATA RAID Functions. (*For the Windows OS
environment, use the RAID driver if this feature is set to "Enabled". If "disabled",
use the "Non-RAID" driver.)
Native Mode Operation
This option allows the user to select the Native Mode for ATA. Some Operating
Systems are not supported by the Native Mode. The options are: Serial ATA,
Parallel ATA, Auto, and Both.
IDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave, IDE
Channel 2 Master, IDE Channel 3 Master
These settings allow the user to set the parameters of IDE Channel 0 Master/
Slave, IDE Channel 1 Master/Slave, IDE Channel 2 Master, IDE Channel 3 Master
slots. Hit <Enter> to activate the following sub-menu screen for detailed options
of these items. Set the correct configurations accordingly. The items included in
the sub-menu are:
Type
This option allows the user to select the type of IDE hard drive. The options are
Auto (allows BIOS to automatically determine the hard drive's capacity, number
of heads, Sectors, Maximum Capacity, LBA Format, ect.). Enter a number from
1-39 to select a predetermined type of hard drive, CD-ROM and ATAPI Removable.
The option- "User" will allow the user to enter the parameters of the HDD installed
at this connection. The option-"Auto" will allow BIOS to automatically configure
the parameters of the HDD installed at the connection. Choose the option"1-39"
7-4
Chapter 7: BIOS
to select a pre-determined HDD type. Select CD-ROM if a CD-ROM drive is
installed. Select ATAPI if a removable disk drive is installed.
Multi-Sector Transfers
Select the number of transfer sectors. The options are Disabled, 2, 4, 6, 8 and
16 Sectors.
LBA Mode Control
This item determines whether Phoenix BIOS will access the IDE Primary Master
Device via LBA mode. The options are Disabled and Enabled.
32 Bit I/O
Selects 32 Bit I/O operation. The options are Enabled and Disabled.
Transfer Mode
Selects the transfer mode. The options are Standard, Fast PIO1, Fast PIO2,
Fast PIO3, Fast PIO4, FPIO3/DMA1 and FPIO4/DMA2.
Ultra DMA Mode
Selects Ultra DMA Mode. The options are Disabled, Mode 0, Mode 1, Mode
2, Mode 3, Mode 4, Mode 5 and Mode 6.
System Memory
This display informs you how much system memory is recognized as being present
in the system.
Extended Memory
This display informs you how much extended memory is recognized as being
present in the system.
7-5
SUPERSERVER 6014H-32 User's Manual
7-4
Advanced Setup
Choose Advanced from the Phoenix BIOS Setup Utility main menu with the arrow
keys. You should see the following display. The items with a triangle beside them
have sub menus that can be accessed by highlighting the item and pressing <Enter>.
Options for PIR settings are displayed by highlighting the setting option using the
arrow keys and pressing <Enter>. All Advanced BIOS Setup options are described
in this section.
Boot Features
Access the submenu to make changes to the following settings.
Quick Boot Mode
If enabled, this feature will speed up the POST (Power On Self Test) routine after
the computer is turned on. The settings are Enabled and Disabled. If Disabled,
the POST routine will run at normal speed.
Quiet Boot
This setting allows you to Enable or Disable the diagnostic screen during bootup.
7-6
Chapter 7: BIOS
ACPI Mode
Use the setting to determine if you want to employ ACPI (Advanced Configuration
and Power Interface) power management on your system. The options are Yes
and No.
Power Button Behavior
If set to Instant-Off, the system will power off immediately as soon as the user hits
the power button. If set to 4-sec, the system will power off when the user presses
the power button for 4 seconds or longer. The options are instant-off and 4-sec
override.
Resume On Modem Ring
Select On to "wake your system up" when an incoming call is received by your
modem. The options are On and Off.
Power Loss Control
This setting allows you to choose how the system will react when power returns
after an unexpected loss of power. The options are Stay On, Power Off and Last
State.
Watch Dog
This setting is for enabling the Watch Dog feature. The options are Enabled and
Disabled.
Summary Screen
This setting allows you to Enable or Disable the summary screen.
Memory Cache
Cache System BIOS Area
This setting allows you to designate a reserve area in the system memory to be
used as a System BIOS buffer to allow the BIOS write (cache) its data into this
reserved memory area. Select "Write Protect" to enable this function, and this
area will be reserved for BIOS ROM access only. Select "Uncached" to disable
this function and make this area available for other devices.
Cache Video BIOS Area
This setting allows you to designate a reserve area in the system memory to be
used as a Video BIOS buffer to allow the BIOS write (cache) its data into this
reserved memory area. Select "Write Protect" to enable the function and this
area will be reserved for BIOS ROM access only. Select "Uncached" to disable
this function and make this area available for other devices.
7-7
SUPERSERVER 6014H-32 User's Manual
Cache Base 0-512K
If enabled, this feature will allow the data stored in the base memory area: block
0-512K to be cached (written) into a buffer, a storage area in the Static DRM
(SDROM) or written into L1, L2, L3 cache inside the CPU to speed up CPU
operations . Select "Uncached" to disable this function. Select "Write Through"
to allow data to be cached into the buffer and written into the system memory
at the same time. Select "Write Protect" to prevent data from being written into
the base memory area of Block 0-512K. Select "Write Back" to allow CPU to write
data back directly from the buffer without writing data to the System Memory for
fast CPU data processing and operation. The options are "Uncached", "Write
Through", "Write Protect", and "Write Back".
Cache Base 512K-640K
If enabled, this feature will allow the data stored in the memory area: 512K-640K
to be cached (written) into a buffer, a storage area in the Static DRM (SDROM)
or written into L1, L2, L3 cache inside the CPU to speed up CPU operations
. Select "Uncached" to disable this function. Select "Write Through" to allow
data to be cached into the buffer and written into the system memory at the
same time. Select "Write Protect" to prevent data from being written into the
base memory area of Block 0-512K. Select "Write Back" to allow CPU to write
data back directly from the buffer without writing data to the System Memory for
fast CPU data processing and operation. The options are "Uncached", "Write
Through", "Write Protect", and "Write Back".
Cache Extended Memory
If enabled, this feature will allow the data stored in the extended memory area
to be cached (written) into a buffer, a storage area in the Static DRM (SDROM)
or written into L1, L2, L3 cache inside the CPU to speed up CPU operations.
Select "Uncached" to disable this function. Select "Write Through" to allow data
to be cached into the buffer and written into the system memory at the same
time. Select "Write Protect" to prevent data from being written into the base
memory area of Block 0-512K. Select "Write Back" to allow CPU to write data
back directly from the buffer without writing data to the System Memory for
fast CPU data processing and operation. The options are "Uncached", "Write
Through", "Write Protect", and "Write Back".
Discrete MTRR Allocation
If enabled, MTRRs (-Memory Type Range Registers) are configured as distinct,
separate units and cannot be overlapped. If enabled, the user can achieve
better graphic effects when using a Linux graphic driver that requires the writecombining configuration with 4GB or more memory. The options are Enabled
and Disabled.
7-8
Chapter 7: BIOS
PCI Configuration
Access the submenu to make changes to the following settings for PCI devices.
Onboard GLAN (Gigabit- LAN) OPROM Configure
Enabling this option provides the capability to boot from GLAN. The options
are Disabled and Enabled.
Default Primary Video Adapter
This option allows the user to decide which video adapt is the default primary
video adapter for the system. The options are Onboard and Other.
PCI Parity Error Forwarding
If set to Enabled, NMI signals will be generated when a PCI Parity Error occurs.
The options are Enabled and Disabled.
ROM Scan Order
If set to Onboard First, the Onboard PCI Option ROM will be activated first
before the Add-On Device Option ROM is activated. The options are Add-On
First and Onboard First.
Reset Configuration Data
If set to Yes, this setting clears the Extended System Configuration Data- (ESCD)
area. The options are Yes and No.
Frequency for PCIX#1/G-LAN
(*Note: *PCIX#1=PCI-X Slot#6 on the MB Silk Screen.)
This option allows the user to change the bus frequency for the devices installed
in the slot indicated. The options are Auto, PCI 33 MHz, PCI 66 MHz, PCI-X
66 MHz, PCI-X 100 MHz, and PCI-X 133 MHz.
Frequency for PCIX#2/MASS/ZCR (MASS: Mass Storage)
(*Note: *PCIX#2=PCI-X Slot#7 on the MB Silk Screen.)
This option allows the user to change the bus frequency of the devices installed
in the slot indicated. The options are Auto, PCI 33 MHz, PCI 66 MHz, PCI-X
66 MHz, PCI-X 100 MHz, and PCI-X 133 MHz.
PCIX-133MHz Slot#1/PCIX-100MHz Slot#2, PCI-Exp x8 Slot#1, and
PCI-Exp x4 Slot#2 (*Note: Slot#1=Slot#6 and Slot#2=Slot#7 as shown on
the MB.)
Access the submenu for the settings above to make changes to the following:
Option ROM Scan
When enabled, this setting will initialize the device expansion ROM. The options
are Enabled and Disabled.
7-9
SUPERSERVER 6014H-32 User's Manual
Enable Master
This setting allows you to enable the selected device as the PCI bus master.
The options are Enabled and Disabled.
Latency Timer
This setting allows you to set the clock rate for Bus Master.A high-priority, highthroughout device may benefit from a greater Clock rate. The options are Default,
0020h, 0040h, 0060h, 0080h, 00A0h, 00C0h, and 00E0h. For Unix, Novell and
other Operating Systems, please select the option: "other". If a drive fails after
the installation of a new software , you might want to change this setting and
try again. Different OS requires different Bus Master clock rate.
Large Disk Access Mode
This setting determines how large hard drives are to be accessed. The options are
DOS or Other (for Unix, Novellle NetWare and other operating systems).
Advanced Chipset Control
Access the submenu to make changes to the following settings.
Force Compliance Mode Entry
This feature allows you to enable the PCI-Express Compliance 1.0 Mode. The
options are: Disabled or Enabled.
Memory RAS Feature Control
Select this option to enable the Memory RAS Feature Control. The options are
Standard, Sparing, and Mirroring.
Clock Spectrum Feature
If "Enabled", BIOS will monitor the level of Electromagnetic Interference caused by
the components and will attempt to decrease the interference whenever needed.
The options are Enabled and Disabled.
Memory Remap Function Control
Set to Enabled to re-allocate memory resources for PCI slots. The options are
Enabled and Disabled.
DRAM Data Integrity Mode
If enabled, this feature allows the data stored in the DRMA memory to be integrated
for faster data processing. The options are 72-bit ECC, 144-bit ECC, Auto and
Disabled.
7-10
Chapter 7: BIOS
ECC Error Type
This setting lets you select which type of interrupt to be activated as a result
of an ECC error. The options are None, NMI (Non-Maskable Interrupt), SMI
(System Management Interrupt) and SCI (System Control Interrupt.)
SERR Signal Condition
This setting specifies the conditions required to be qualified as an ECC error. The
options are None, Single Bit, Multiple Bit and Both.
Enabling Multi-Media Timer
Select Yes to enable Multi-Media Timer. The options are Yes and No.
USB Functions
This setting allows you to Enable or Disable all functions for the USB devices
specified.
Legacy USB Support
This setting allows you to enable support for Legacy USB devices. The settings
are Enabled and Disabled.
Advanced Processor Options
Access the submenu to make changes to the following settings.
CPU Speed
This is a display that indicates the speed of the installed processor.
Hyper-Threading Technology (*Available if supported by the CPU.)
This setting allows you to Enable or Disable the function of hyper-threading.
Enabling hyper-threading results in increased CPU performance. (Applicable for
the XP systems.)
Machine Checking
Set to Enabled to allow the operating system to debug a system crash after a reset.
The options are Disabled and Enabled.
C1 Enhanced Mode (*Available when supported by the CPU.)
Set to Enabled to enable the Enhanced Halt State. The options are Enabled and
Disabled. (*Note: please refer to Intel's web site for detailed information.)
7-11
SUPERSERVER 6014H-32 User's Manual
No Execute Mode Memory Protection (*Available when supported by the
CPU.)
Enable this feature to enable the functionality of Execute Disable Bit and allow
the processor to classify areas in the memory where an application code can
execute and where it cannot, and thus preventing a worm or a virus from inserting
and creating a flood of codes that will overwhelm the processor or damage the
system during an attack. (*Note: this feature is available when your OS and your
CPU support the function of Execute Disable Bit.) The options are Disabled and
Enabled. (*Note: For more information regarding hardware/software support for
this function, please refer to Intel's and Microsoft's web sites.)
Thermal Management 2 (*Available when supported by the CPU.)
If enabled, this feature allows you to select between Thermal Manager 1 and Thermal
Manager 2. Set to Disable to activate the function of TM1, allowing the CPU to
regulate its power consumption based upon the modulation of the CPU Internal
clock when the CPU temperature reaches a pre-defined overheat threshold. Set
to Enable to activate the function of TM2, which will allow the CPU to reduce its
power consumption by lowering the CPU frequency and the CPU voltage when the
CPU temperature reaches a pre-defined overheat threshold. (*Note: please refer
to Intel's web site for detailed information.)
Adjacent Cache Line Prefetch
The CPU fetches the cache line for 64 bytes if Dtisabled. The CPU fetches both
cache lines for 128 bytes as comprised if Enabled.
Processor Power Management (*Available when supported by the CPU.)
This feature allows the user to determine the processor power management
mode. If set to C States only, the processor power will be controlled through CPU
power states in the ACPI setting. Select "GV1/GV3 only" to enable the function of
DBS (Demand Based Switching) which will allow the user to configure CPU power
management in the OS. If set to Disabled, C States and GV1/GV3 are disabled. If
set to Enabled, C States and GV1/GV3 are Enabled. (*Note: please refer to Intel's
web site for detailed information.)
7-12
Chapter 7: BIOS
I/O Device Configuration
Access the submenu to make changes to the following settings.
KBC Clock Input
This setting allows you to set the clock frequency for the Keyboard Clock. The
options are 6MHz, 8MHz, 12 MHz and 16MHz.
On-board COM 1
This setting allows you to assign control of serial port A. The options are Enabled
(user defined), Disabled and Auto (BIOS controlled).
Base I/O Address
Select the base I/O address for serial port A. The options are 3F8, 2F8,
3E8 and 2E8.
Interrupt
Select the IRQ (interrupt request) for serial port A. The options are IRQ3
and IRQ4.
On-board COM 2
This setting allows you to assign control of serial port B. The options are Enabled
(user defined), Disabled and Auto (BIOS controlled).
Mode
Specify the type of device that will be connected to serial port B. The options
are Normal, and IR (for an infrared device).
Base I/O Address
Select the base I/O address for serial port B. The options are 3F8, 2F8,
3E8 and 2E8.
Interrupt
Select the IRQ (interrupt request) for serial port B. The options are IRQ3
and IRQ4.
Floppy Disk Controller
This setting allows you to assign control of the floppy disk controller. The
options are Enabled (user defined), Disabled and Auto (BIOS controlled).
Base I/O Address
Select the base I/O address for the parallel port. The options are Primary
and Secondary.
7-13
SUPERSERVER 6014H-32 User's Manual
DMI Event Logging
Access the submenu to make changes to the following settings.
Event Log Validity
This is a display, not a setting, informing you of the event log validity.
Event Log Capacity
This is a display, not a setting, informing you of the event log capacity.
View DMI Event Log
Highlight this item and press <Enter> to view the contents of the event log.
Event Logging
This setting allows you to Enable or Disable event logging.
ECC Event Logging
This setting allows you to Enable or Disable ECC event logging.
Mark DMI Events as Read
Highlight this item and press <Enter> to mark the DMI events as read.
Clear All DMI Event Logs
Select Yes and press <Enter> to clear all DMI event logs. The options are Yes
and No.
Console Redirection
Access the submenu to make changes to the following settings.
COM Port Address
Specifies to redirect the console to On-board COM A or On-board COM B. This
setting can also be Disabled.
BAUD Rate
Select the BAUD rate for console redirection. The options are 300, 1200, 2400,
9600, 19.2K, 38.4K, 57.6K and 115.2K.
Console Type
Choose from the available options to select the console type for console redirection. The
options are VT100, VT100,8bit, PC-ANSI, 7bit, PCANSI, VT100+, VT-UTF8.
Flow Control
Choose from the available options to select the flow control for console redirection.
The options are: None, XON/XOFF, and CTS/RTS.
7-14
Chapter 7: BIOS
Console Connection
Select the console connection: either Direct or Via Modem.
Continue CR after POST
This option allows the user to decide whether to continue with console
redirection after the POST routine. The options are On and Off.
Hardware Monitor Logic
CPU Temperature Threshold
This option allows the user to set a CPU temperature threshold that will activate
the alarm system when the CPU temperature reaches this pre-set temperature
threshold. The options are 75oC, 80oC, 85oC and 90oC.
Highlight this and hit <Enter> to see the status of the following items:
CPU1 Temperature: This item displays CPU1 Temperature.
CPU2 Temperature: This item displays CPU2 Temperature.
System Temperature: This item displays the system Temperature.
Fan Speed Control Modes: [Disable (Full Speed), 3-pin (Server)]
This feature allows the user to decide how the system controls the speeds of onboard
fans. Select "Disable" to disable of the function of fan speed control and the system
will run at the full speed (12V.) Select "3-pin Server" to optimize the fan speed control
via BIOS Thermal management. The default setting is 3-pin Server.
Fan 1/ Fan 2/Fan 3/Fan 4/Fan 5
The voltage status of the following items will also be displayed:
Vcore A
Vcore B
P3V3
P5V
N12V
P12V
VDD
P5Vsb
7-15
SUPERSERVER 6014H-32 User's Manual
7-5
Security
Choose Security from the Phoenix BIOS Setup Utility main menu with the arrow
keys. You should see the following display. Security setting options are displayed
by highlighting the setting using the arrow keys and pressing <Enter>. All Security
BIOS settings are described in this section.
Supervisor Password Is:
This displays whether a supervisor password has been entered for the system.
Clear means such a password has not been used and Set means a supervisor
password has been entered for the system.
User Password Is:
This displays whether a user password has been entered for the system. Clear
means such a password has not been used and Set means a user password has
been entered for the system.
Set Supervisor Password
When the item "Set Supervisor Password" is highlighted, hit the <Enter> key. When
prompted, type the Supervisor's password in the dialogue box to set or to change
supervisor's password, which allows access to BIOS.
7-16
Chapter 7: BIOS
Set User Password
When the item "Set User Password" is highlighted, hit the <Enter> key. When
prompted, type the user's password in the dialogue box to set or to change the
user's password, which allows access to the system at boot-up.
Fixed Disk Boot Sector
This setting may offer some protection against viruses when set to Write Protect,
which protects the boot sector on the hard drive from having a virus written to it.
The other option is Normal.
Password on Boot
This setting allows you to require a password to be entered when the system
boots up. The options are Enabled (password required) and Disabled (password
not required).
7-6
Boot
Choose Boot from the Phoenix BIOS Setup Utility main menu with the arrow keys.
You should see the following display. Highlighting a setting with a + or - will expand
or collapse that entry. See details on how to change the order and specs of boot
devices in the Item Specific Help window. All Boot BIOS settings are described in
this section.
7-17
SUPERSERVER 6014H-32 User's Manual
+Removable Devices
Highlight and press <Enter> to expand the field. See details on how to change the
order and specs of devices in the Item Specific Help window.
CD-ROM Drive
See details on how to change the order and specs of the CD-ROM drive in the
Item Specific Help window.
+Hard Drive
Highlight and press <Enter> to expand the field. See details on how to change the
order and specs of hard drives in the Item Specific Help window.
7-7
Exit
Choose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys.
You should see the following display. All Exit BIOS settings are described in this
section.
7-18
Chapter 7: BIOS
Exit Saving Changes
Highlight this item and hit <Enter> to save any changes you made and to exit the
BIOS Setup utility.
Exit Discarding Changes
Highlight this item and hit <Enter> to exit the BIOS Setup utility without saving any
changes you may have made.
Load Setup Defaults
Highlight this item and hit <Enter> to load the default settings for all items in the
BIOS Setup. These are the safest settings to use.
Discard Changes
Highlight this item and hit <Enter> to discard (cancel) any changes you made.
You will remain in the Setup utility.
Save Changes
Highlight this item and hit <Enter> to save any changes you made. You will remain
in the Setup utility.
7-19
SUPERSERVER 6014H-32 User's Manual
Notes
7-20
Appendix A: BIOS POST Codes
Appendix A
BIOS POST Codes
This section lists the POST (Power On Self Test) codes for the PhoenixBIOS. POST
codes are divided into two categories: recoverable and terminal.
Recoverable POST Errors
When a recoverable type of error occurs during POST, the BIOS will display an
POST code that describes the problem.
BIOS may also issue one of the follow-
ing beep codes:
1 long and two short beeps - video configuration error
1 continuous long beep - overheat (Overheat LED will be on)
1 long beep and 1 short pause - memory not detected
Terminal POST Errors
If a terminal type of error occurs, BIOS will shut down the system. Before doing so,
BIOS will write the error to port 80h, attempt to initialize video and write the error
in the top left corner of the screen.
The following is a list of codes that may be written to port 80h.
POST Code
02h
03h
04h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Eh
0Fh
10h
11h
12h
13h
14h
16h
17h
Description
Verify Real Mode
Disable Non-Maskable Interrupt (NMI)
Get CPU type
Initialize system hardware
Disable shadow and execute code from the ROM.
Initialize chipset with initial POST values
Set IN POST flag
Initialize CPU registers
Enable CPU cache
Initialize caches to initial POST values
Initialize I/O component
Initialize the local bus IDE
Initialize Power Management
Load alternate registers with initial POST values
Restore CPU control word during warm boot
Initialize PCI Bus Mastering devices
Initialize keyboard controller
1-2-2-3 BIOS ROM checksum
Initialize cache before memory Auto size
A-1
SUPERSERVER 6014H-32 User’s Manual
POST Code
Description
18h
8254 timer initialization
1Ah
1Ch
8237 DMA controller initialization
Reset Programmable Interrupt Controller
20h
1-3-1-1 Test DRAM refresh
22h
1-3-1-3 Test 8742 Keyboard Controller
24h
Set ES segment register to 4 GB
28h
29h
Auto size DRAM
Initialize POST Memory Manager
2Ah
Clear 512 kB base RAM
2Ch
1-3-4-1 RAM failure on address line xxxx*
2Eh
1-3-4-3 RAM failure on data bits xxxx* of low byte of
memory bus
Enable cache before system BIOS shadow
Test CPU bus-clock frequency
Initialize Phoenix Dispatch Manager
Warm start shut down
Shadow system BIOS ROM
Auto size cache
Advanced configuration of chipset registers
Load alternate registers with CMOS values
Initialize extended memory for RomPilot
Initialize interrupt vectors
POST device initialization
2-1-2-3 Check ROM copyright notice
Initialize I20 support
Check video configuration against CMOS
Initialize PCI bus and devices
Initialize all video adapters in system
QuietBoot start (optional)
Shadow video BIOS ROM
Display BIOS copyright notice
Initialize MultiBoot
Display CPU type and speed
Initialize EISA board
Test keyboard
Set key click if enabled
Enable USB devices
2-2-3-1 Test for unexpected interrupts
Initialize POST display service
Display prompt “Press F2 to enter SETUP”
Disable CPU cache
2Fh
32h
33h
36h
38h
3Ah
3Ch
3Dh
41h
42h
45h
46h
47h
48h
49h
4Ah
4Bh
4Ch
4Eh
4Fh
50h
51h
52h
54h
55h
58h
59h
5Ah
5Bh
A-2
Appendix A: BIOS POST Codes
POST Code
Description
5Ch
Test RAM between 512 and 640 kB
60h
62h
Test extended memory
Test extended memory address lines
64h
Jump to UserPatch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
69h
Enable external and CPU caches
Setup System Management Mode (SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
6Eh
70h
72h
76h
7Ch
7Dh
7Eh
80h
81h
82h
83h
84h
85h
86h
87h
88h
89h
8Ah
8Bh
8Ch
8Fh
90h
91h
92h
93h
95h
96h
97h
98h
Display shadow-area message
Display possible high address for UMB recovery
Display error messages
Check for configuration errors
Check for keyboard errors
Set up hardware interrupt vectors
Initialize Intelligent System Monitoring
Initialize coprocessor if present
Disable onboard Super I/O ports and IRQs
Late POST device initialization
Detect and install external RS232 ports
Configure non-MCD IDE controllers
Detect and install external parallel ports
Initialize PC-compatible PnP ISA devices
Re-initialize onboard I/O ports.
Configure Motherboard Configurable Devices (optional)
Initialize BIOS Data Area
Enable Non-Maskable Interrupts (NMIs)
Initialize Extended BIOS Data Area
Test and initialize PS/2 mouse
Initialize floppy controller
Determine number of ATA drives (optional)
Initialize hard-disk controllers
Initialize local-bus hard-disk controllers
Jump to UserPatch2
Build MPTABLE for multi-processor boards
Install CD ROM for boot
Clear huge ES segment register
Fix up Multi Processor table
1-2 Search for option ROMs. One long, two short beeps on checksum failure
A-3
SUPERSERVER 6014H-32 User’s Manual
POST Code
Description
99h
Check for SMART Drive (optional)
9Ah
9Ch
Shadow option ROMs
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI drives
A0h
A2h
Set time of day
Check key lock
A4h
Initialize typematic rate
A8h
Erase F2 prompt
AAh
ACh
AEh
B0h
B1h
B2h
B4h
B5h
B6h
B7h
B9h
BAh
BBh
BCh
BDh
BEh
BFh
C0h
C1h
C2h
C3h
C4h
C5h
C6h
C7h
C8h
C9h
CAh
CBh
Scan for F2 key stroke
Enter SETUP
Clear Boot flag
Check for errors
Inform RomPilot about the end of POST.
POST done - prepare to boot operating system
1 One short beep before boot
Terminate QuietBoot (optional)
Check password (optional)
Initialize ACPI BIOS
Prepare Boot
Initialize SMBIOS
Initialize PnP Option ROMs
Clear parity checkers
Display MultiBoot menu
Clear screen (optional)
Check virus and backup reminders
Try to boot with INT 19
Initialize POST Error Manager (PEM)
Initialize error logging
Initialize error display function
Initialize system error handler
PnPnd dual CMOS (optional)
Initialize note dock (optional)
Initialize note dock late
Force check (optional)
Extended checksum (optional)
Redirect Int 15h to enable remote keyboard
Redirect Int 13h to Memory Technologies
Devices such as ROM, RAM, PCMCIA, and serial disk
Redirect Int 10h to enable remote serial video
CCh
A-4
Appendix A: BIOS POST Codes
POST Code
Description
CDh
Re-map I/O and memory for PCMCIA
CEh
D2h
Initialize digitizer and display message
Unknown interrupt
The following are for boot block in Flash ROM
POST Code
Description
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
E3h
Initialize the CPU
Initialize system timer
E4h
E5h
E6h
E7h
E8h
E9h
EAh
EBh
ECh
EDh
EEh
EFh
F0h
F1h
F2h
F3h
F4h
F5h
F6h
F7h
Initialize system I/O
Check force recovery boot
Checksum BIOS ROM
Go to BIOS
Set Huge Segment
Initialize Multi Processor
Initialize OEM special code
Initialize PIC and DMA
Initialize Memory type
Initialize Memory size
Shadow Boot Block
System memory test
Initialize interrupt vectors
Initialize Run Time Clock
Initialize video
Initialize System Management Manager
Output one beep
Clear Huge Segment
Boot to Mini DOS
Boot to Full DOS
If the BIOS detects error 2C, 2E, or 30 (base 512K RAM error), it displays an additional
word-bitmap (xxxx) indicating the address line or bits that failed. For example, “2C
0002” means address line 1 (bit one set) has failed. “2E 1020" means data bits 12
and 5 (bits 12 and 5 set) have failed in the lower 16 bits. The BIOS also sends the
bitmap to the port-80 LED display. It first displays the checkpoint code, followed by
a delay, the high-order byte, another delay, and then the loworder byte of the error.
It repeats this sequence continuously.
A-5
SUPERSERVER 6014H-32 User’s Manual
Notes
A-6
Appendix B: Software Installation
Appendix B
Software Installation
B-1 Introduction to the Adaptec SATA RAID Controller
Serial ATA (SATA)
Serial ATA(SATA) is a physical storage interface. It uses a single cable with a
minimum of four wires to create a point-to-point connection between devices. It
is a serial link which supports SATA Transfer rates from 150MBps. Because the
serial cables used in SATA are thinner than the traditional cables used in Parallel
ATA(PATA), SATA systems have better airflow and can be installed in smaller
chassis than Parallel ATA. In addition, the cables used in PATA can only extend
to 40cm long, while Serial ATA cables can extend up to one meter. Overall, Serial
ATA provides better functionality than Parallel ATA.
Introduction to the Intel 6300ESB I/O Controller Hub
Located in the South Bridge of the Intel E7520 Chipset, the 6300ESB I/O Controller Hub provides the I/O subsystem with access to the rest of the system. It
supports 2-channel Ultra ATA/100 Bus Master IDE controller (PATA) and two Serial
ATA (SATA) Host Controllers, which support up to two Serial ATA ports and up to
two RAID drives. The 6300ESB I/O Controller Hub supports the following Parallel
ATA (PATA) and Serial (SATA) device configurations:
ATA Operating Mode
You can select from the following two modes: Combined Mode and Enhanced
Mode.
B-1
SUPERSERVER 6014H-32 User’s Manual
Combined Mode
In this mode, system BIOS assigns the traditional IRQ 14 and IRQ 15 for the
use of HDD. Up to 4 ATA devices are supported by this mode.
Within the Combined Mode, the following three modes are supported:
*Non-Combined Mode: Parallel ATA only:with the maximum of 4 devices supported;
*Non-Combined Mode: Serial ATA only:with the maximum of 2 devices supported;
*Combined Mode: SATA devices and PATA: with the support of 2 devices each
(total: 4 devices maximum). (For IDE/SATA configurations, please refer to the
table below.)
Primary Master(=PM)
Yes Yes No
No
No
No
Primary Slave(=PS)
Yes No
Yes No
No
No
Secondary Master(=SM) Yes No
No
Yes No
No
Secondary Slave(=SS)
Yes No
No
No
Yes No
SATA Port0
No
SM
SM
PM
PM
PM
SATA Port1
No
SS
SS
PS
PS
PS
*Note: (No=Not Present, Yes=Present) Also, if Logical Primary is
selected, the IDE channels are no longer available.
Enhanced Mode
In this mode, system BIOS will automatically search for all available IRQs for the
use of HDD. For newer Operating Systems that support the Enhanced Mode,
such as Windows XP, Windows 2000, and Windows 2003, you can set SATA
and PATA to the Enhanced Mode. (*The newer Operating Systems can accommodate both Enhanced Mode and Combined Mode and support up to 6 ATA
devices.)
(*Please refer to the "Advanced Chipset Control" under the "Advanced" Setup in
the BIOS for the selection of Combined Mode or Enhanced Mode,).
B-2
Appendix B: Software Installation
Configuring BIOS settings for the SATA RAID Functions
(Enhanced Mode)
1. Press the <Del> key during system bootup to enter the BIOS Setup Utility. (If
it is the first time to power on the system, we recommend that you load the Optimized Default Settings. If you have already done so, please skip to Step 3.
2. Use the arrow keys to select the "Exit" Menu. Once in the "Exit" Menu, scroll
down the menu to select the item- "Load System Default" and press the <Enter>
key. Select "OK" to confirm the selection. Press the <Enter> key to load the
default settings to the BIOS.
3. Use the arrow keys to select the "Main" Menu in the BIOS.
4. Scroll down to "SATA RAID Enable" and press the <Enter> Key to select this
option.
5. From this submenu, select "Enable" and press <Enter>.
6. Tap the <Esc> key and scroll down to "Exit". Select "Save and Exit" from the
"Exit" menu. Press the <Enter> key to save the changes and exit the BIOS.
7. Once you've exited the BIOS Utility, the system will re-boot.
8. During the system startup, press the <Ctrl> and the <A> keys simultaneously
to run the Adaptec RAID Configuration Utility when prompted by the following
message:
Press <Ctrl><A> for Adaptec RAID Configuration Utility.
B-3
SUPERSERVER 6014H-32 User’s Manual
Adaptec SATA with HostRAID Controller Driver
Adaptec's Embedded Serial ATA RAID with HostRAID controller adds RAID functionality to the Serial ATA I/O controller by supporting RAID 0 (Striping) or RAID
1 (Mirroring) to enhance the industry's pioneer PCI-to-e host controller products.
RAID striping (RAID 0) can greatly improve hard disk I/O performance because
of its capability in striping data across multiple drives. RAID mirroring (RAID 1)
allows the data to be simultaneously written to two drives, so critical data is always available even if a single hard disk fails. Due to the built-in functionality, the
X6DH3-G2 is specially designed to keep pace with the increasing performance
demands of computer systems by improving disk I/O throughput and providing
data accessibility regardless of a single disk failure. By incorporating the Adaptec
Embedded Serial ATA into the motherboard design, Supermicro's X6DH3-G2
offers the user with the benefits of SATARAID without the high costs associated
with hardware RAID applications.
(*Note: For Adaptec's RAID Driver Installation Instructions, please refer to the
Adaptec RAID Controller User's Guide: "Emb_SA_RAID_UG.pdf" in the CD that
came with this motherboard. You can also download a copy of Adaptec's User's
Guide from our web site at www.supermicro.com.)
Using the Adaptec RAID Configuration Utility (ARC)
The Adaptec RAID Configuration Utility is an embedded BIOS Utility, including:
*Array Configuration Utility: Use this utility when you want to create, configure
and manage arrays.
* Disk Utilities: Use this option to format or verify disks.
To run the Adaptec RAID Configuration Utility, you will need to enable the RAID
function in the system BIOS (refer to Chapter 4 for System BIOS Configurations),
and then, press the <Ctrl> and <A> keys simultaneously when prompted to do so
during the system startup. (Refer to the previous page for detailed instructions.)
Note: To select an option, use the arrow keys to highlight the item and then
press the <Enter> key to select it. To return to the previous menu, press the
<ESC> key.
A. Using the Array Configuration Utility (ACU)
The Array Configuration Utility (ACU) enables you to create, manage, and delete
arrays from the controller’s BIOS, add and delete spare drives, and initialize drives.
During the system startup, press <Ctrl> and <A> key simultaneously, and the main
menu will appear.
B-4
Appendix B: Software Installation
Managing Arrays
Select this option to view array properties, and delete arrays. The following sections describe the operations Of "Managing Arrays".
To select this option, use the arrow keys and the <enter> key to select "Managing
Arrays" from the main menu (as shown above).
B-5
SUPERSERVER 6014H-32 User’s Manual
Viewing Array Properties
To view the properties of an existing array:
1. At the BIOS prompt, press Ctrl+A.
2. From the ARC menu, select Array Configuration Utility (ACU).
3. From the ACU menu, select Manage Arrays (as shown on the previous screen.)
4. From the List of Arrays dialog box, select the array you want to view and press
Enter.
The Array Properties dialog box appears, showing detailed information on the array. The physical disks associated with the array are displayed here.
5. Press Esc to return to the previous menu.
Deleting Arrays
Warning: Back up the data on an array before you delete it to prevent the loss of
data. Deleted arrays cannot be restored.
To delete an existing array:
1. Turn on your computer and press Ctrl+A when prompted to access the ARC
utility.
2. From the ARC main menu, select Array Configuration Utility
(ACU).
3. From the ACU menu, select Manage Arrays.
4. Select the array you wish to delete and press Delete.
5. In the Array Properties dialog box, select Delete and press
Enter. The following prompt is displayed:
Warning!! Deleting the array will render array unusable. Do you want to delete the
array?(Yes/No):
RAID 1 only—the following prompt is also displayed:
Deleting the partition will result in data loss! Do you also want to delete the partition? (Yes/No):
6. Press Yes to delete the array or partition or No to return to the previous menu.
7. Press Esc to return to the previous menu.
B-6
Appendix B: Software Installation
Creating Arrays
Before creating arrays, make sure the disks for the array are connected and
installed in your system. Note that disks with no usable space, or disks that are uninitialized are shown in gray and cannot be used. See Initializing Disk Drives.
To create an array:
1. Turn on your computer and press Ctrl+A when prompted to access the ARC
utility.
2. From the ARC menu, select Array Configuration Utility Main Menu (ACU) (as
shown on the first screen on page B-5).
3. From the ACU menu, select Create Array.
4. Select the disks for the new array and press Insert (as the screen shown below).
Note: To deselect any disk, highlight the disk and press Delete.
5. Press Enter when both disks for the new array are selected. The Array Properties menu displays (as the screen shown below).
B-7
SUPERSERVER 6014H-32 User’s Manual
Assigning Array Properties
Once you've create a new array, you are ready to assign the properties to the array.
Caution: Once the array is created and its properties are assigned, you cannot
change the array properties using the ACU. You will need to use the Adaptec Storage Manager - Browser Edition. (Refer to Adaptec's User's Guide in the enclosed
CD.)
To assign properties to the new array:
1. In the Array Properties menu (as shown in the screen below), select an array
type and press Enter.
Note that only the available array types: RAID 0, and RAID1, are displayed on the
screen. (*RAID 0 or RAID 1 requires two drives.
2. Under the item "Arrays Label", type in an label and press Enter. (The label
shall not be more than 15 characters.
B-8
Appendix B: Software Installation
3. For RAID 0, select the desired stripe size. (*Note: Available stripe sizes
are 16, 32, and 64 KB-default. It is recommended that you do not change the
default setting.)
4. The item: "Create RAID via" allows you to select between the different creating
methods for RAID 0 and RAID 1.
The following table gives examples of when each is appropriate.
Raid Level
RAID 0
RAID 0
RAID 1
Create Via
No Init
Migrate
(*Note)
Build1
RAID 1
Clear
RAID 1
Quick
RAID 1
Init
When Appropriate
Creating a RAID 0 on new drives
Creating a RAID 0 from one new drive and
one drive with data you wish to preserve
Any time you wish to create a RAID 1, but especially if
you have data on one drive that you wish to preserve
Creating a RAID 1 on new drives, or when you want to
ensure that the array contains no data after creation.
Fastest way to create a RAID 1.
Appropriate when using new drives
Note: If you select Migrate for RAID 0, or Build for RAID 1, you will be asked
to select the source drive. The contents of the source drive will be preserved.
However, the data on the new drive will be lost.
5. When you are finished, press Done (as the screen shown below).
B-9
SUPERSERVER 6014H-32 User’s Manual
Notes:
1. Before adding a new drive to an array, back up any data contained on the new
drive. Otherwise, all data will be lost.
2. If you stop the Build or Clear process on a RAID 1 from ACU, you can restart it
by pressing Ctrl+R.
3. A RAID 1 created using the Quick Init option may return some data mis-compares if you later run a consistency check. This is normal and is not a cause for
concern.
4. The ACU allows you to use drives of different sizes in a
RAID . However, during a build operation, only the smaller drive can be selected as
the source or first drive.
5. When migrating from single volume to RAID 0, migrating from a larger drive to
a smaller drive is allowed. However, the destination drive must be at least half the
capacity of the source drive.
6. Adaptec does not recommend that you migrate or build an array on Windows
dynamic disks (volumes), as it will result in data loss.
Warning: Do not interrupt the creation of a RAID 0 using the Migrate option. If you
do, you will not be able to restart, or to recover the data that was on the source
drive.
B-10
Appendix B: Software Installation
Adding a Bootable Array
To make an array bootable:
1. From the Main menu, select Manage Arrays.
2. From the List of Arrays, select the array you want to make
bootable, and press Ctrl+B.
3. Enter Y to create a bootable array when the following message is displayed:
"This will make all other existing bootable array non-bootable. Do you want to make
this array bootable? (Yes/No):" A bootable array will then be created and an asterisk will appear next to the bootable array (as shown in the picture below:)
Deleting a Bootable Array
To delete a bootable array:
1. From the Main menu, select Manage Arrays.
2. From the List of Arrays, select the bootable array you want to delete, and press
Ctrl+B. (A bootable array is the array marked with an asterisk, as shown in the
picture above.)
3. Enter Y to delete a bootable array when the following message is displayed:
"The array is already marked bootable. Do you want to make this array as not
bootable? (Yes/No):" Then, the bootable array will be deleted and the asterisk will
disappear. Note: do not use the delete key to delete the bootable array.
B-11
SUPERSERVER 6014H-32 User’s Manual
Initializing Disk Drives
If an installed disk does not appear in the disk selection list for creating a new array, or if it appears grayed out, you may have to initialize it before you can use it as
part of an array. Drives attached to the controller must be initialized before they can
be used in an array.
Caution: Initializing a disk overwrites the partition table on the disk and makes any
data on the disk inaccessible. If the drive is used in an array, you may not be able
to use the array again.
Do not initialize a disk that is part of a boot array. To determine which disks are
associated with a particular array, please refer to Viewing Array Properties.
To initialize drives:
1. Turn on your computer and press Ctrl+A when prompted to access the ARC
utility.
2. From the ARC menu, select Array Configuration Utility (ACU) (as shown in the
screen below).
3. Select Initialize Drives (as shown in the screen below).
B-12
Appendix B: Software Installation
4. Use the up and down arrow keys to select the disk you wish to initialize and
press Insert (as shown in the screen below).
B-13
SUPERSERVER 6014H-32 User’s Manual
5. Repeat Step 4 so that both drives to be initialized are selected (as shown below).
6. Press Enter.
7. Read the warning message as shown below.
8. Make sure that you have selected the correct disk drives to initialize. If correct,
type Y to continue.
B-14
Appendix B: Software Installation
Rebuilding Arrays
Note 1: Rebuilding applies to Fault Tolerant array (RAID 1) only.
If an array Build process (or initialization) is interrupted or critical with one member
missing, you must perform a Rebuild to get the array to Optimal status. For a critical array Rebuild operation, the optimal drive is the source drive.
Note 2: If no spare array exists and a hard disk drive fails, you need to create a
spare before you can rebuild an array.
To Rebuild an array:
1. From the Main Menu, select Manage Arrays (as shown in the screen below).
From the List of Arrays, select the array you want to Rebuild.
2. Press Ctrl+R to Rebuild.
B-15
SUPERSERVER 6014H-32 User’s Manual
Adaptec SAS/SATA with HostRAID Controller Driver
The onboard Adaptec AIC9140W SAS Controller supports two ports. Each port
supports up to four SAS/SATA drives.
* The SAS Cable (CBL-097) can only be used with backplanes that support both
SAS and SATA.
* If Supermicro's chassis is used, the backplane must be Rev.2.0 or above, which
came with gold trims.
* If you want to use this motherboard with Supermicro's SAS Mobile Racks, such
as CSE-M28E1, make sure to use Cable CBL-0116. (*Note: Cable CBL-0116 is a
corss-over cable, and is not provided with this motherboard.)
Using the Adaptec RAID Configuration Utility (ARC)
The onboard SAS Controller is enabled by default. To disable it, please set
Jumper JPS1 to Pins 2-3 (See Page 2-5 for details and jumper location.)
* Upon detecting the SAS Controller BIOS, please make sure that the Adapter
WWN address is listed. This is a 16-digit number. If this number is not shown,
you will not be able to use the controller.
* Once the WWN address is listed, press the <Ctrl> and <A> keys simultaneously when prompted to access the Adaptec SAS RAID BIOS. (*Note: To select
an option, use the arrow keys to highlight the item and then press the <Enter>
key to select it. To return to the previous menu, press the <ESC> key.)
The Adaptec RAID Configuration Utility is an embedded BIOS Utility, including:
*Array Configuration Utility: Use this utility when you want to create, configure
and manage arrays.
* SerialSelect Utility: Use this option to configure SAS/SATA RAID drives.
* Disk Utilities: Use this option to format or verify disks.
A. Using the Array Configuration Utility (ACU)
The Array Configuration Utility (ACU) enables you to create, manage, and delete
arrays from the controller’s BIOS, add and delete spare drives, and initialize drives.
During the system startup, press <Ctrl> and <A> key simultaneously, and the main
menu will appear.
B-16
Appendix B: Software Installation
Managing Arrays
Select this option to view array properties, and delete arrays. The following sections describe the operations Of "Managing Arrays".
To select this option, use the arrow keys and the <enter> key to select "Managing
Arrays" from the main menu.
Viewing Array Properties
To view the properties of an existing array:
1. At the BIOS prompt, press Ctrl+A.
2. From the ARC menu, select Array Configuration Utility (ACU).
3. From the ACU menu, select Manage Arrays (as shown on the previous screen.)
4. From the List of Arrays dialog box, select the array you want to view and press
Enter.
The Array Properties dialog box appears, showing detailed information on the array. The physical disks associated with the array are displayed here.
5. Press Esc to return to the previous menu.
B-17
SUPERSERVER 6014H-32 User’s Manual
Deleting Arrays
Warning: Back up the data on an array before you delete it to prevent the loss of
data. Deleted arrays cannot be restored.
To delete an existing array:
1. Turn on your computer and press Ctrl+A when prompted to access the ARC
utility.
2. From the ARC main menu, select Array Configuration Utility
(ACU).
3. From the ACU menu, select Manage Arrays.
4. Select the array you wish to delete and press Delete.
5. In the Array Properties dialog box, select Delete and press Enter. The following
prompt is displayed:
Warning!! Deleting the array will render array unusable. Do you want to delete the
array?(Yes/No):
RAID 1 only—the following prompt is also displayed:
Deleting the partition will result in data loss! Do you also want to delete the partition? (Yes/No):
6. Press Yes to delete the array or partition or No to return to the previous menu.
7. Press Esc to return to the previous menu.
Creating Arrays
Before creating arrays, make sure the disks for the array are connected and
installed in your system. Note that disks with no usable space, or disks that are uninitialized are shown in gray and cannot be used. See Initializing Disk Drives.
To create an array:
1. Turn on your computer and press Ctrl+A when prompted to access the ARC
utility.
2. From the ARC menu, select Array Configuration Utility Main Menu (ACU) (as
shown on the first screen on the previus page).
3. From the ACU menu, select Create Array.
4. Select the disks for the new array and press Insert.
Note: To deselect any disk, highlight the disk and press Delete.
5. Press Enter when both disks for the new array are selected. The Array Properties menu displays.
B-18
Appendix B: Software Installation
Assigning Array Properties
Once you've create a new array, you are ready to assign the properties to the array.
Caution: Once the array is created and its properties are assigned, you cannot
change the array properties using the ACU. You will need to use the Adaptec Storage Manager - Browser Edition. (Refer to Adaptec's User's Guide in the enclosed
CD.)
To assign properties to the new array:
1. In the Array Properties menu, select an array type and press Enter. Note that
only the available array types: RAID 0, and RAID1, are displayed on the screen.
(RAID 0 or RAID 1 requires two drives.)
2. Under the item "Arrays Label", type in an label and press Enter. The label
shall not be more than 15 characters.
3. For RAID 0, select the desired stripe size. Available stripe sizes are 16, 32, and
64 KB-default. It is recommended that you do not change the default setting.)
4. The item: "Create RAID via" allows you to select between the different creating
methods for RAID 0 and RAID 1.
The following table gives examples of when each is appropriate.
Raid Level
RAID 0
RAID 0
RAID 1
Create Via
No Init
Migrate
(*Note)
Build1
RAID 1
Clear
RAID 1
Quick
RAID 1
Init
When Appropriate
Creating a RAID 0 on new drives
Creating a RAID 0 from one new drive and
one drive with data you wish to preserve
Any time you wish to create a RAID 1, but especially if
you have data on one drive that you wish to preserve
Creating a RAID 1 on new drives, or when you want to
ensure that the array contains no data after creation.
Fastest way to create a RAID 1.
Appropriate when using new drives
Note: If you select Migrate for RAID 0, or Build for RAID 1, you will be asked
to select the source drive. The contents of the source drive will be preserved.
However, the data on the new drive will be lost.
5. When you are finished, press Done.
Notes:
1. Before adding a new drive to an array, back up any data contained on the new
drive. Otherwise, all data will be lost.
2. If you stop the Build or Clear process on a RAID 1 from ACU, you can restart it
by pressing Ctrl+R.
B-19
SUPERSERVER 6014H-32 User’s Manual
3. A RAID 1 created using the Quick Init option may return some data mis-compares if you later run a consistency check. This is normal and is not a cause for
concern.
4. The ACU allows you to use drives of different sizes in a RAID . However, during
a build operation, only the smaller drive can be selected as the source or first drive.
5. When migrating from single volume to RAID 0, migrating from a larger drive to
a smaller drive is allowed. However, the destination drive must be at least half the
capacity of the source drive.
6. Adaptec does not recommend that you migrate or build an array on Windows
dynamic disks (volumes), as it will result in data loss.
Warning: Do not interrupt the creation of a RAID 0 using the Migrate option. If you
do, you will not be able to restart, or to recover the data that was on the source
drive.
Adding a Bootable Array
To make an array bootable:
1. From the Main menu, select Manage Arrays.
2. From the List of Arrays, select the array you want to make bootable, and press
Ctrl+B.
3. Enter Y to create a bootable array when the following message is displayed:
"This will make all other existing bootable array non-bootable. Do you want to make
this array bootable? (Yes/No):" Then, a bootable array will be created. An asterisk
will appear next to the bootable array.
Deleting a Bootable Array
To delete a bootable array:
1. From the Main menu, select Manage Arrays.
2. From the List of Arrays, select the bootable array (*) you want to delete, and
press Ctrl+B. (* a bootable array is the array marked with an asterisk.)
3. Enter Y to delete a bootable array when the following message is displayed:
"The array is already marked bootable. Do you want to make this array as not
bootable? (Yes/No):" Then, the bootable array will be deleted and the asterisk will
disappear.
Note: do not use the delete key to delete the bootable array.
B-20
Appendix B: Software Installation
Initializing Disk Drives
If an installed disk does not appear in the disk selection list for creating a new array,
or if it appears grayed out, you may have to initialize it before you can use it as part
of an array. Drives attached to the controller must be initialized before they can be
used in an array.
Caution: Initializing a disk overwrites the partition table on the disk and makes any
data on the disk inaccessible. If the drive is used in an array, you may not be able to
use the array again.
Do not initialize a disk that is part of a boot array. To determine which disks are associated with a particular array, please refer to Viewing Array Properties.
To initialize drives:
1. Turn on your computer and press Ctrl+A when prompted to access the ARC
utility.
2. From the ARC menu, select Array Configuration Utility (ACU).
3. Select Initialize Drives.
4. Use the up and down arrow keys to highlight the disk you wish to initialize and
press Insert.
5. Repeat Step 4 so that both drives to be initialized are selected.
6. Press Enter.
7. Read the warning message displayed in the screen.
8. Make sure that you have selected the correct disk drives to initialize. If correct,
type Y to continue.
Rebuilding Arrays
Notes: Rebuilding applies to Fault Tolerant array (RAID 1) only. If an array Build
process (or initialization) is interrupted or critical with one member missing, you
must perform a Rebuild to get the array to Optimal status. For a critical array Rebuild operation, the optimal drive is the source drive.
If no spare array exists and a hard disk drive fails, you need to create a spare
before you can rebuild an array.
To Rebuild an array:
1. From the Main Menu, select Manage Arrays. From the List of Arrays, select the
array you want to Rebuild.
2. Press Ctrl+R to Rebuild.
B-21
SUPERSERVER 6014H-32 User’s Manual
Using the SerialSelect Utility to Configure SAS Settings
The SerialSelect Utility enables you to configure SAS disk drive settings.
To access the SAS utilities:
1. Turn on your computer and press Ctrl+A when prompted to access the ARC utility. (as shown in the screen below.)
2. Use the arrow keys to select "SerialSelect Utility" and press <Enter> to access
the Controller Configuration submenu:
B-22
Appendix B: Software Installation
To set the controller configuration:
3. Select "Controller Configuration" and press <Enter> to access the submen as
shown below:
4. Use the arrow keys to select an item. Then, press <Enter> and the arrow keys to
configure the setting for the item selected.
5. To load the default settings, press <F6>. Note: The default setting for each item
is listed below:
Runtime BIOS: Enabled,
BBS Support: Device,
POST Banner Display: Enabled,
CTRL-A Message Display: Enabled,
Physical Drives Display during POST: Enabled,)
6. Press <Esc> to return to the previous menu and to exit the utility.
B-23
SUPERSERVER 6014H-32 User’s Manual
To Set the Physical Configuration:
1. Turn on the computer and press Ctrl+A when prompted to access the ARC utility.
2. Use the arrow keys to select "SerialSelect Utility" and press <Enter> to access
the Physical Configuration submenu as shown below:
3. Select "Physical Configuration" and press <Enter> to access SAS Device Configuration submenu as shown below:
B-24
Appendix B: Software Installation
4. Use the arrow keys to select an item. Then, press <Enter> and the arrow keys
to configure the item selected.
5. To load default settings, press <F6>.
6. Press <Esc> to return to the previous menu and to exit the utility.
Using the Disk Utilities
The Disk Utilities enable you to format or verify the media of your Serial ATA hard
disks.
To access the disk utilities:
1. Turn on your computer and press Ctrl+A when prompted to access the ARC utility (as shown in the screen below.)
2. From the ARC menu, select Disk Utilities from the screen as shown above and
press Enter.
3. When the submenu appears, select the desired disk and press Enter
The following options are available:
1. Format Disk—Simulates a low-level format of the hard drive by writing zeros to
the entire disk. Note: Serial ATA drives are low-level formatted at the factory and do
not need to be low-level formatted again. Caution: Formatting disk erases all data
on the drive. Be sure to back up your data before performing this operation.)
B-25
SUPERSERVER 6014H-32 User’s Manual
2. Verify Disk Media—Scans the media of a disk drive for defects.
To Exit Adaptec RAID Configuration Utility
1. Once you have completed RAID array configurations, press ESC to exit. The
following screen will appear.
2. Press Yes to exit the Utility.
For more information regarding Adaptec RAID Utility, please refer to Adaptec's User's Guide in the CD included in your shipping package. You can
also download a copy of Adaptec User's Guide from our web site at: www.
supermicro.com.)
B-26
Appendix B: Software Installation
B-2 Installing the 6300ESB/SAS Driver and the OS
a. Insert Supermicro's bootable CD that came with the package into the CD Drive
during the system reboot, and the screen:"Super Micro Driver Diskette Maker"
will appear.
b. From the list displayed on the screen, choose the item: "Intel 6300 ESB/ICH5R
Driver by 3rd Party (Adaptec)" or "SAS" and press <ENTER>.
c. From the next screen displayed, choose the OS driver you want to install and
press <Enter>.
d. Insert a formatted diskette into drive A: and press <Enter> as prompted.
e. Exit the program after the process is completed. Then, reboot the system.
f. Insert Microsoft Windows OS Setup CD in the CD Driver, and the system will
start to boot up from CD.
g. Press the <F6> key when the message-"Press F6 if you need to install a third
party SCSI or RAID driver" displays.
h. When the Windows OS Setup screen appears, press "S" to specify additional
device(s).
i. Insert the driver diskette-"Adaptec Embedded Serial ATA Raid Controller Driver"
into Drive A: and press the <Enter> key.
j. Choose Adaptec Embedded Host Serial ATA Raid Controller from the list indicated in the Windows OS Setup Screen, and press the <Enter> key.
k. Press the <Enter> key to continue the installation process. (If you need to
specify any additional devices to be installed, do it at this time.) Once all devices
are specified, press the <Enter> key to continue with the installation.
l. From the Windows OS Setup screen, press the <Enter> key. The OS Setup will
automatically load all device files, and, then, continue the Windows OS installation.
m. After Windows OS Installation is completed, the system will automatically
reboot.
B-27
SUPERSERVER 6014H-32 User’s Manual
B-3 Installing Other Software Programs and Drivers
A. Installing Drivers other than Adaptec Embedded Serial
ATA RAID Controller Driver
After you've installed Windows Operating System, a screen as shown below will
appear. You are ready to install software programs and drivers that have not yet
been installed. To install these software programs and drivers, click the icons to
the right of these items.
Driver/Tool Installation Display Screen
Note: Click the icons showing a hand writing on paper to view the readme files
for each item. Click the computer icons to the right of these items to install each
item (from top to the bottom) one at a time. After installing each item, you must
re-boot the system before moving on to the next item on the list. You should
install everything here except for the Supero Doctor utility, Intel LDCM and the
LAN/SCSI driver diskettes, which are optional. The bottom icon with a CD on it
allows you to view the entire contents of the CD.
Please refer to the Adaptec User's Guide for the installation of Adaptec's Serial
ATA RAID Controller Driver. Adaptec's User's Guide is included in the CD. You
can also download a copy of the user's guide from our web site.
B-28
Appendix B: Software Installation
Supero Doctor III
The Supero Doctor III program is a Web base management tool that supports remote
management capability. It includes Remote and Local Management tools. The local
management is called SD III Client. The Supero Doctor III program included on the
CDROM that came with your motherboard allows you to monitor the environment
and operations of your system. Supero Doctor III displays crucial system information
such as CPU temperature, system voltages and fan status. See the Figure below
for a display of the Supero Doctor III interface.
Note: The default User Name and Password for SuperDoctor III is ADMIN / ADMIN.
Note: When SuperDoctor III is first installed, it adopts the temperature threshold
settings that have been set in BIOS. Any subsequent changes to these thresholds
must be made within Super Doctor, as the Super Doctor settings override the BIOS
settings. To set the BIOS temperature threshold settings again, you would first need
to uninstall SuperDoctor III.
Supero Doctor III Interface Display Screen-I (Health Information)
B-29
SUPERSERVER 6014H-32 User’s Manual
Supero Doctor III Interface Display Screen-II (Remote Control)
Notes: 1. SD III Software Revision 1.0 can be downloaded from our Web site at:
ftp://ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII
User's Guide at: http://www.supermicro.com/PRODUCT/Manuals/SDIII/UserGuide.
pdf. For Linux, we will still recommend Supero Doctor II. 2. For detailed information on Adaptec's SCSI SATA RAID Utility, please refer to the CDs that came
with your motherboard.
B-30
Appendix C: System Specifications
Appendix C
System Specifications
Processors
Single or dual Intel® Xeon™ 604-pin processors to 3.60 GHz at a front side
(system) bus speed of 800 MHz.
Note: Please refer to our web site for a complete listing of supported processors.
Chipset
Intel E7520 chipset
BIOS
8 Mb Phoenix® Flash ROM
Memory Capacity
Eight 240-pin DIMM sockets supporting up to 16 GB of DDR2-400 SDRAM
Note: Dual channel memory - requires memory to be installed two modules at a time. See the
memory section in Chapter 5 for details.
Serial Attached SCSI/Serial ATA Controller
• Adaptec 9410W controller for 4-port SAS/SATA (RAID 0,1,10 and JBOD
supported)
• Intel ICH5R on-chip controller for 2-port Serial ATA (RAID 0,1 and JBOD
supported)
SAS/SATA Drive Bays
Four (4) hot-swap drive bays to house four (4) standard SAS/SATA drives
Peripheral Drive Bays
One (1) slim 3.5" floppy drive
One (1) slim CD-ROM drive
C-1
SUPERSERVER 6014H-32 User's Manual
Expansion Slots (provided with included riser cards)
One (1) 64-bit 133 MHz standard size PCI-X slot and one (1) 64-bit 66 MHz
low profile PCI-X slot (with CSE-RR1U-X and CSE-RR1U-XLP riser cards)
An additional two riser cards are available as an option to support add-on
cards in the SXB-E1 and SXB-E2 x8 (PCI-Express) slots (CSE-RR1U-EL and
CSE-RR1U-ELP).
Motherboard
Model: X6DHR-3G2 (Extended ATX form factor)
Dimensions: 12 x 13.05 in (305 x 332 mm)
Chassis
Model: SC813T-500 Form Factor: 1U rackmount
Dimensions: (WxHxD) 17.2 x 1.7 x 25.6 in. (437 x 44 x 650 mm)
Weight
Gross (Bare Bone): 38 lbs. (17.3 kg.)
System Cooling
Two (2) 10-cm blower fans
System Input Requirements
AC Input Voltage: 100-240V AC auto-range
Rated Input Current: 10A (115V) to 5A (230V)
Rated Input Frequency: 50 to 60 Hz
Power Supply
Rated Output Power: 500W (Model# SP502-1S, Part# PWS-048)
Rated Output Voltages: +3.3V (21A), +5V (30A), +12V (39A), +5Vsb (2A)
BTU Rating
2750 BTUs/hr (for rated output power of 500W)
Operating Environment
Operating Temperature: 10º to 35º C (50º to 95º F)
Non-operating Temperature: -40º to 70º C (-40º to 158º F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
C-2
Appendix C: System Specifications
Regulatory Compliance
Electromagnetic Emissions:
FCC Class A, EN 55022 Class A, EN 61000-3-2/-3-3, CISPR 22 Class A
Electromagnetic Immunity:
EN 55024/CISPR 24, (EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,
EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11)
Safety:
EN 60950/IEC 60950-Compliant, UL Listed (USA), CUL Listed (Canada), TUV
Certified (Germany), CE Marking (Europe)
California Best Management Practices Regulations for Perchlorate Materials:
This Perchlorate warning applies only to products containing CR (Manganese
Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate”
C-3
SUPERSERVER 6014H-32 User's Manual
Notes
C-4
">