fire - parts . com
NATURAL GAS LOG
VENTED DECORATIVE APPLIANCE
OWNER’S MANUAL
Models BVTR18
and BVTR24
TESTED AND
LISTED BY
RGA 2-72
APPROVED
FOR USE WITH
CANYON SPLIT LOG SETS
INCLUDED WITH HEARTH KITS
Std RADCO Listing No. 1292
fire-parts.com
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the
fire department.
— Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
WARNING: Improper installation,
adjustment, alteration, service, or
maintenance can cause injury or
property damage. Refer to this
manual for correct installation and
operational procedures. For assistance or additional information consult a qualified installer, service
agency, or the gas supplier.
WARNING: This appliance is for
installation only in a solid-fuel
burning masonry or UL127 factory-built fireplace, constructed of
noncombustible material, and connected to a working flue. (See page
7 for minimum flue opening.)
WARNING: This is a gas-fired appliance. It uses air (oxygen) from the room in which it is installed.
Provisions for adequate combustion and ventilation air must be provided. Refer to Air for
Combustion and Ventilation section on page 4 of this manual.
This appliance may be installed in an aftermarket* manufactured (mobile) home, where not
prohibited by state or local codes.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer
Save this manual for future reference.
2
TABLE OF CONTENTS
SAFETY INFORMATION
TABLE OF CONTENTS
SAFETY INFORMATION ............................................................ 2
OPERATING APPLIANCE ........................................................ 13
PRODUCT IDENTIFICATION ..................................................... 3
CLEANING AND MAINTENANCE ............................................ 14
LOCAL CODES ........................................................................... 3
TROUBLESHOOTING .............................................................. 15
UNPACKING ............................................................................... 3
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ....... 18
OPTIONAL PRODUCT FEATURES ........................................... 3
REPLACEMENT PARTS .......................................................... 22
AIR FOR COMBUSTION AND VENTILATION ........................... 4
ACCESSORIES ........................................................................ 22
INSTALLATION ........................................................................... 7
WARRANTY INFORMATION ...................................... Back Cover
SAFETY INFORMATION
WARNING ICON
G 001
WARNINGS
1.
WARNING: Keep flue open when operating unit.
2.
This appliance, as supplied, is only for use with the type of gas
indicated on the rating plate. This appliance is convertible for use
with propane/LP, using the GA9053A or GA9153A pilot kit.
If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use any phone in
your building
• immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions
• if you cannot reach your gas supplier, call the fire department
Never install the log set
• in a recreational vehicle
• where curtains, furniture, clothing, or other flammable objects are less than 42 inches from the front, top, or sides of
the log set
• in high traffic areas
• in windy or drafty areas
Before installing in a solid fuel burning fireplace, the chimney
flue and firebox must be cleaned of soot, creosote, ashes, and
loose paint by a qualified chimney cleaner. Creosote will ignite if highly heated. Inspect chimney flue for damage.
You must operate this log set with a fireplace screen in place.
Make sure fireplace screen is closed before running log set.
This log set is designed to be smokeless. If logs ever appear to
smoke, turn off appliance and call a qualified service person.
Note: During initial operation, slight smoking could occur due
to log curing and the burning of manufacturing residues. You
may wish to add more ventilation by opening a window.
To reduce the creation of soot, follow the instructions in Cleaning and Maintenance, page 14.
Do not allow fans to blow directly into the fireplace. Avoid
any drafts that alter burner flame patterns. Ceiling fans can
create drafts that alter burner flame patterns. Altered burner
patterns can increase sooting.
Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this log set.
fire-parts.com
IMPORTANT: Read this owner’s manual carefully and
completely before trying to assemble, operate, or service this log set. Improper use of this log set can cause
serious injury or death from burns, fire, explosion,
electrical shock, and carbon monoxide poisoning.
DANGER: Carbon monoxide poisoning may lead
to death!
3.
Carbon Monoxide Poisoning: Early signs of carbon monoxide
poisoning resemble the flu, with headaches, dizziness, or nausea. If
you have these signs, the log set may not be working properly. Get
fresh air at once! Have log set serviced. Some people are more
affected by carbon monoxide than others. These include pregnant
women, people with heart or lung disease or anemia, those under the
influence of alcohol, and those at high altitudes.
4.
Natural Gas: Natural gas is odorless. An odor-making agent is
added to the gas. The odor helps you detect a gas leak. However, the
odor added to the gas can fade. Gas may be present even though no
odor exists.
Make certain you read and understand all warnings. Keep this
manual for reference. It is your guide to safe and proper operation
of this log set.
WARNING: Any change to this log set or its
controls can be dangerous.
5.
6.
7.
8.
9.
109484
SAFETY INFORMATION
PRODUCT IDENTIFICATION
LOCAL CODES
UNPACKING
OPTIONAL PRODUCT FEATURES
SAFETY INFORMATION
3
3
LOCAL CODES
Continued
10. This log set needs fresh, outside air ventilation to run properly.
See Air for Combustion and Ventilation, pages 4 through 6.
11. Do not run log set
• where flammable liquids or vapors are used or stored
• under dusty conditions
12. Do not burn solid fuel in the fireplace after installing the log set.
Do not use this log set to cook food or burn paper or other objects.
13. Log set becomes very hot when in use. Keep children and adults
away from hot surface to avoid burns or clothing ignition. Log
set will remain hot for a time after shutdown. Allow surface to
cool before touching.
14. Carefully supervise young children when they are in the room
with log set.
15. Do not use appliance if any part has been exposed to or under
water. Immediately call a qualified service technician to inspect
the room appliance and to replace any part of the control system (if using GA9053A or GA9153A) and any gas control which
has been under water.
16. To help prevent breakage, new logs must be broken-in (see
Curing Logs page 14).
17. Turn log set off and let cool before servicing, installing, or repairing. Only a qualified service person should install, service, or repair log set.
Install and use log set with care. Follow all local codes. In the absence
of local codes, use the latest edition of The National Fuel Gas Code
ANSI Z223.1/NFPA 54*.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
UNPACKING
CAUTION: Do not remove the metal data plates from
the burner pan. The data plates contain important
product and warranty information.
fire-parts.com
PRODUCT IDENTIFICATION
Rear Burner
Grate
1.
2.
3.
Remove logs, hearth kit, pan materials, and hardware from carton.
Remove all protective packaging applied to logs and base for
shipment.
Check all items for any shipping damage. If damaged, promptly
inform dealer where you bought the product.
OPTIONAL PRODUCT
FEATURES
ON/OFF SAFETY VALVE/PILOT KIT AND
PROPANE/LP CONVERSION
An optional valve/safety pilot kit with a piezo ignitor is available for
this appliance. This system requires no matches, batteries, or other
sources to light. You must use this optional system for LP conversion. See Accessories, page 23.
REMOTE CONTROL READY (MILLIVOLT)
SAFETY VALVE/PILOT KIT
Burner
Pan
Front
Burner
Figure 1 - Product Identification
Valve
Cover
Serial Number __________________________
An optional millivolt valve/safety pilot kit with a piezo ignitor is
available for this appliance. This system requires no matches,
batteries, or other sources to light. This system may be connected to
a wall switch or hand-held wireless remote control. See Accessories, page 22.
REMOTE CONTROL ACCESSORIES
There is an optional hand-held ON/OFF remote control that can be
purchased separately for this log set. You must use the millivolt
valve/safety pilot kit to use remote accessories with this appliance.
See Accessories, page 22.
109484
4
AIR FOR COMBUSTION AND VENTILATION
Providing Adequate Ventilation
AIR FOR COMBUSTION AND
VENTILATION
WARNING: This appliance shall not be installed in
a confined space or unusually tight construction
unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other
fuel-burning appliances in your home.
Today’s homes are built more energy efficient than ever. New
materials, increased insulation, and new construction methods help
reduce heat loss in homes. Home owners weather strip and caulk
around windows and doors to keep the cold air out and the warm air
in. During heating months, home owners want their homes as airtight
as possible.
While it is good to make your home energy efficient, your home
needs to breathe. Fresh air must enter your home. All fuel-burning
appliances need fresh air for proper combustion and ventilation.
Unusually Tight Construction
The air that leaks around doors and windows may provide enough
fresh air for combustion and ventilation. However, in buildings of
unusually tight construction, you must provide additional fresh air.
Unusually tight construction is defined as construction
where:
a. walls and ceilings exposed to the outside atmosphere
have a continuous water vapor retarder with a rating
of one perm (6x10-11 kg per pa-sec-m2) or less with
openings gasketed or sealed and
b. weather stripping has been added on openable windows and doors and
c. caulking or sealants are applied to areas such as
joints around window and door frames, between sole
plates and floors, between wall-ceiling joints, between
wall panels, at penetrations for plumbing, electrical,
and gas lines, and at other openings.
fire-parts.com
Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances
draw air from the house to operate. You must provide adequate fresh
air for these appliances. This will insure proper venting of vented
fuel-burning appliances.
PROVIDING ADEQUATE VENTILATION
The following are excerpts from National Fuel Gas Code. ANSI Z223.1/
NFPA 54, Air for Combustion and Ventilation.
All spaces in homes fall into one of the three following ventilation
classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 4 through 6 will help you classify your
space and provide adequate ventilation.
If your home meets all of the three criteria above, you
must provide additional fresh air. See Ventilation Air
From Outdoors, page 6.
If your home does not meet all of the three criteria above,
proceed to Determining Fresh-Air Flow For Appliance
Location, page 5.
Confined and Unconfined Space
The National Fuel Gas Code ANS Z223.1/NFPA 54 defines a
confined space as a space whose volume is less than 50 cubic feet
per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating
of all appliances installed in that space and an unconfined space as
a space whose volume is not less than 50 cubic feet per 1,000 Btu per
hour (4.8 m3 per kw) of the aggregate input rating of all appliances
installed in that space. Rooms communicating directly with the
space in which the appliances are installed*, through openings not
furnished with doors, are considered a part of the unconfined space.
* Adjoining rooms are communicating only if there are doorless
passageways or ventilation grills between them.
109484
AIR FOR COMBUSTION AND VENTILATION
Determining Fresh-Air Flow for Appliance Location
5
5
AIR FOR COMBUSTION AND
VENTILATION
Continued
DETERMINING FRESH-AIR FLOW FOR APPLIANCE LOCATION
Determining if You Have a Confined or Unconfined Space
Use this work sheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install appliance plus
any adjoining rooms with doorless passageways or ventilation grills
between the rooms.
1. Determine the volume of the space (length x width x height).
Length x Width x Height = _________________ cu. ft. (volume of space)
Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft.
(ceiling height) = 2560 cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills
or openings, add the volume of these rooms to the total volume of the space.
2. Multiply the space volume by 20 to determine the maximum
Btu/Hr the space can support.
_____________ (volume of space) x 20 = (maximum Btu/Hr
the space can support)
Example: 2560 cu. ft. (volume of space) x 20 = 51,200 (maximum Btu/Hr the space can support)
3. Add the Btu/Hr of all fuel burning appliances in the space.
Gas fireplace logs
_____________ Btu/Hr
Gas water heater*
_____________ Btu/Hr
Gas furnace
_____________ Btu/Hr
Vented gas heater
_____________ Btu/Hr
Vent-free heater
_____________ Btu/Hr
Other gas appliances* + _____________ Btu/Hr
Total
= _____________ Btu/Hr
* Do not include direct-vent gas appliances. Direct-vent draws
combustion air from the outdoors and vents to the outdoors.
Example:
Gas water heater
40,000
Btu/Hr
Gas fireplace logs
+
55,000
Btu/Hr
Total
=
95,000
Btu/Hr
4.
Compare the maximum Btu/Hr the space can support with the
actual amount of Btu/Hr used.
_____________ Btu/Hr (maximum the space can support)
_____________ Btu/Hr (actual amount of Btu/Hr used)
Example: 51,200 Btu/Hr (maximum the space can support)
95,000 Btu/Hr (actual amount of Btu/Hr used)
The space in the above example is a confined space because the
actual Btu/Hr used is more than the maximum Btu/Hr the space can
support. You must provide additional fresh air. Your options are as
follows:
A. Rework worksheet, adding the space of an adjoining room. If
the extra space provides an unconfined space, remove door to
adjoining room or add ventilation grills between rooms. See
Ventilation Air From Inside Building, page 6.
B. Vent room directly to the outdoors. See Ventilation Air From
Outdoors, page 6.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room
unconfined.
fire-parts.com
109484
If the actual Btu/Hr used is less than the maximum Btu/Hr the space
can support, the space is an unconfined space. You will need no
additional fresh air ventilation.
WARNING: If the area in which the appliance may
be operated is smaller than that defined as an unconfined space or if the building is of unusually tight
construction, provide adequate combustion and ventilation air by one of the methods described in the
National Fuel Gas Code, ANSI Z223.1/NFPA 54, Section 5.3 or applicable local codes.
6
AIR FOR COMBUSTION AND VENTILATION
Ventilation Air
AIR FOR COMBUSTION AND
VENTILATION
Continued
VENTILATION AIR
12"
Ventilation Air From Inside Building
This fresh air would come from an adjoining unconfined space.
When ventilating to an adjoining unconfined space, you must
provide two permanent openings: one within 12" of the ceiling and
one within 12" of the floor on the wall connecting the two spaces
(see options 1 and 2, Figure 2). You can also remove door into
adjoining room (see option 3, Figure 2). Follow the National Fuel
Gas Code, ANS Z223.1/NFPA 54, Section 5.3, Air for Combustion
and Ventilation for required size of ventilation grills or ducts.
Ventilation
Grills
Into Adjoining
Room,
Option 1
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills or ducts. You must
provide two permanent openings: one within 12" of the ceiling and
one within 12" of the floor. Connect these items directly to the
outdoors or spaces open to the outdoors. These spaces include attics
and crawl spaces. Follow the National Fuel Gas Code, ANS Z223.1/
NFPA 54, Section 5.3, Air for Combustion and Ventilation for
required size of ventilation grills or ducts.
Ventilation Grills
Into Adjoining Room,
Option 2
Or
Remove
Door into
Adjoining
Room,
Option
3
12"
fire-parts.com
IMPORTANT: Do not provide openings for inlet or outlet air into
attic if attic has a thermostat-controlled power vent. Heated air
entering the attic will activate the power vent.
Figure 2 - Ventilation Air from Inside Building
Outlet
Air
Ventilated
Attic
Outlet
Air
To Attic
To
Crawl
Space
Inlet
Air
Inlet Air
Ventilated
Crawl Space
Figure 3 - Ventilation Air from Outdoors
109484
INSTALLATION
7
7
Flue Opening Specifications
Check Gas Type
Venting Specifications for Installation
Installing Damper Clamp
INSTALLATION
CAUTION: Do not remove the metal data plates
attached to the burner pan. The data plates contain
important warranty information.
WARNING: Before installing in a solid fuel burning fireplace, the chimney flue and firebox must be
cleaned of soot, creosote, ashes and loose paint by
a qualified chimney cleaner. Creosote will ignite if
highly heated. A dirty chimney flue may create and
distribute soot within the house. Inspect chimney
flue for damage.
NOTICE: Installation, service, and repair of this appliance must be performed by a qualified installer,
service agency, company or gas supplier experienced with this type of gas appliance. Only factory
authorized components listed in these instructions
may be used in accordance with the manufacturer’s
instructions and all codes and requirements of the
authority having jurisdiction. Any modifications to
this kit, or use of unauthorized components or accessory items will void the manufacturer’s warranty, and
may result in a hazardous condition.
CHECK GAS TYPE
Use only natural gas. If your gas supply is not natural gas, you must
install ON/OFF Safety Valve/Pilot Kit (see Accessories, page 22).
Call dealer where you bought log set.
If the fireplace does not have a gas supply shutoff valve, one must
be installed.
VENTING SPECIFICATIONS FOR INSTALLATION
The fireplace chimney flue and vent must be drafting properly. To
check the vent for proper drafting: Light a tightly rolled newspaper
on one end and place it at the inside front edge of the fireplace.
Observe the smoke and be sure the vent is properly drawing it up the
chimney. If the smoke spills out into the room, extinguish the flame
and remove any obstruction until proper venting is achieved.
The chimney flue must remain open a minimum of 3" at all times
during the operation of this log set.
fire-parts.com
INSTALLING DAMPER CLAMP
Secure the damper stop clamp provided to the leading edge of the
damper as shown in Figure 5. If for any reason this clamp doesn't
work on your fireplace, another suitable clamp or permanent stop
must be installed, or the damper blade must be cut or removed.
Damper Clamp
Damper Clamp
FLUE OPENING SPECIFICATIONS
Note: This vented appliance must be installed only in a solid-fuel
burning fireplace with a working flue and constructed of noncombustible material.
The charts in Figure 4 indicate technical information regarding the
installation of your gas log set. Please make sure that all of the
specifications shown are applicable before installation is attempted.
The fireplace must include a working flue and venting system with
the minimum openings shown in the Figure 4.
MODEL
DESCRIPTION
BVTR18
BVTR24
18" Triple Burner
24" Triple Burner
60,000
70,000
50,000
60,000
8" dia.
8" dia.
Figure 4 - Technical Information Charts
FUEL INLET PRESSURE
SPECIFICATIONS ("W.C.)
NG
LP
Manufactured
Fireplace
Figure 5 - Attaching Damper Clamp
Minimum
Vent Opening
*Add 2" if safety valve/pilot is used **At depth indicated
109484
Masonry Fireplace
Btu Input
Propane Gas
DEPTH HEIGHT
14"
18"
15 1/2"
18"
Damper
Damper
Btu Input
Natural Gas
MINIMUM FIREBOX SIZES
LOG FRONT BACK
SIZE WIDTH* WIDTH**
18"
28"
16"
24"
29 3/4"
17"
Damper
Min.
5.5
11
Max.
10.5
13
BURNER ORIFICE
LOG
NATURAL
PROPANE/LP
SIZE FRONT REAR FRONT REAR
18"
.046 4x.064 .036 4x.043
24"
.064 4x.064 .036 4x.0465
8
INSTALLATION
Connecting to Gas Supply
Checking Gas Connections
INSTALLATION
Continued
CONNECTING TO GAS SUPPLY
WARNING: A qualified service person must connect log set to gas supply. Follow all local codes.
Installation Items Needed
Before installing log set, make sure you have the items listed below.
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve
• test gauge connection
• adjustable (crescent) wrench or pliers
• sediment trap
• tee joint
• pipe wrench
Installation must include an equipment shutoff valve, union, and
plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from log set (see Figure 6).
IMPORTANT: Install equipment shutoff valve in an accessible
location. The equipment shutoff valve is for turning on or shutting
off the gas to the appliance.
Apply pipe joint sealant lightly to male NPT threads. This will
prevent excess sealant from going into pipe. Excess sealant in pipe
could result in a clogged burner injector.
WARNING: Use pipe joint sealant that is resistant
to liquid petroleum (LP) gas.
We recommend that you install a sediment trap in supply line as shown
in Figure 6. Locate sediment trap where it is within reach for cleaning.
Install in piping system between fuel supply and heater. Locate
sediment trap where trapped matter is not likely to freeze. A sediment
trap traps moisture and contaminants. This keeps them from going into
log set controls. If sediment trap is not installed or is installed wrong,
log set may not run properly.
fire-parts.com
Approved Flexible Gas Hose
(if allowed by local codes)
CHECKING GAS CONNECTIONS
WARNING: Test all gas piping and connections
for leaks after installing or servicing. Correct all
leaks at once.
CSA Design-Certified
Equipment Shutoff Valve
With 1/8" NPT Tap*
3" Minimum
Cap
WARNING: Never use an open flame to check for
a leak. Apply a noncorrosive leak detection fluid to
all joints. Bubbles forming show a leak. Correct all
leaks at once.
From Gas Meter
(5" W.C.** to 10.5"
W.C. Pressure)
Pipe Nipple Tee Joint
Pressure Testing Gas Supply Piping System
Sediment Trap
Figure 6 - Gas Connection
Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)
1.
* Purchase the optional CSA design-certified equipment shutoff
valve from your dealer. See Accessories, page 22.
** Minimum inlet pressure for purpose of input adjustment.
2.
CAUTION: Use only new, black iron or steel pipe.
Internally-tinned copper tubing may be used in certain
areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to log set. If
pipe is too small, undue loss of volume will occur.
4.
3.
5.
6.
Disconnect log set and its individual equipment shutoff valve
from gas supply piping system.
Cap off open end of gas pipe where equipment shutoff valve
was connected.
Pressurize supply piping system by either using compressed air or
opening main gas valve located on or near gas meter.
Check all joints of gas supply piping system. Apply noncorrosive
leak detection fluid to all joints. Bubbles forming show a leak.
Correct all leaks at once.
Reconnect log set and equipment shutoff valve to gas supply.
Check reconnected fittings for leaks.
109484
INSTALLATION
Checking Gas Connections (Cont.)
Hearth Kit Assembly and Installation
9
9
INSTALLATION
Continued
Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)
1.
2.
3.
4.
Close equipment shutoff valve (see Figure 7).
Pressurize supply piping system by either using compressed air or
opening main gas valve located on or near gas meter.
Check all joints from gas meter to equipment shutoff valve (see
Figure 7). Apply noncorrosive leak detection fluid to all joints.
Bubbles forming show a leak.
Correct all leaks at once.
8.
9.
Install the "U" burner from the left side with the open end in
the front (see Figure 9). Hold the rear of the burner higher than
the bracket. Slide the burner over the air restrictor fitting. Lower
the rear of the burner into the slots on the burner bracket. Install the burner clip and tighten the nuts and screws.
Install 3/8 flare x 3/8 male pipe elbow into the inlet of the
manifold block. Install the pipe plug into the top of the manifold block. Use thread sealant.
Rear Burner Nozzle
Equipment Shutoff Valve
Air Restrictor
Pipe Nipple
Gas Meter
Manifold
Block
fire-parts.com
Front Burner
Burner
Inlet Fitting
Figure 8 - Kit Assembly
Figure 7 - Checking Gas Joints
Grate
Burner Bracket
HEARTH KIT ASSEMBLY AND INSTALLATION
Kit Assembly
Note: Be sure all pipe threaded connections are tight, and have
thread compound to prevent leaks.
1. Remove burner inlet fitting from front burner (installed in
burner pan, see Figure 8).
2. Make sure ports on front burner are facing the front (open side)
of burner pan. Refit if needed.
3. Using thread sealant (resistant to the action of propane/LP gas)
on larger end of fitting, screw the burner inlet fitting through
the hole and into the front burner (see Figure 8). Tighten using
a 7/8" wrench. If using propane/LP gas, see Propane/LP Gas
Conversion, page 11.
4. Apply thread sealant compound to the 3/8" male threads of the
burner inlet fitting. Thread the manifold block (see Figure 8)
onto the burner inlet fitting. Use the bottom hole of the block.
5. Apply thread sealant to the 1/8" brass pipe nipple and thread it
onto the manifold block. Tighten with a 7/16" wrench.
6. Slip the air restrictor over the 1/8" pipe nipple. Apply thread
sealant to the male threads and install the rear burner nozzle
onto the fitting. Tighten with a 9/16" wrench.
7. Place the grate assembly over the burner pan. Install the rear
burner bracket onto the grate with the 2 black Phillips head #10
screws provided. Do not tighten at this time (see Figure 9).
109484
Burner
Clip
Burner Pan
Pipe
Plug
Pipe Elbow
Figure 9 - Installing Burner
10
INSTALLATION
Hearth Kit Assembly and Installation (Cont.)
Optional GA9053A Series ON/OFF Safety Valve/Pilot Kit Assembly
INSTALLATION
Continued
Installation and Gas Connection
1.
2.
3.
4.
6.
Thread the gas supply fitting to the fireplace gas supply pipe.
Use thread sealant.
Place the burner pan assembly in the center of the fireplace
floor. Make sure the front of pan faces forward.
Install the flex gas line to the gas supply fitting. Carefully shape
tube to attach to adapter fitting (see Figure 10).
Replace valve cover.
7.
8.
9.
Place the burner pan assembly in the center of the fireplace
floor. Make sure the front of pan faces forward.
Test for leaks following instructions under Testing Burner for
Leaks, page 12.
Retighten and adjust the location of the gas control as necessary. The gas control should be level, with the control rod to
the front.
Install valve cover to burner pan using screws provided.
Close Pipe Nipple
Gas Supply
Fitting
fire-parts.com
Gas Line
Burner Pan Assembly
(Facing Front of Fireplace)
Figure 10 - Connecting Gas to Appliance
Burner
Pan
Manifold
Block
Control Rod
Gas Control
Valve
Figure 11 - Installing Gas Control Valve
OPTIONAL GA9053A SERIES ON/OFF
SAFETY VALVE/PILOT KIT ASSEMBLY
For additional convenience and safety, or for propane/LP conversion, an optional ON/OFF safety valve/pilot kit is available. See
Accessories, page 22.
WARNING: You must use a ON/OFF safety valve/
pilot kit for propane/LP conversion.
Natural Gas Installation
1.
2.
3.
4.
5.
Thread the gas control valve onto the close pipe nipple (see
Figure 11). Use thread sealant on the male threads of the fitting. Thread other end of the nipple into the burner manifold
block. Hold the manifold block with a wrench to prevent stressing the connections to the burners. Make sure the control rod
is facing the front (see Figure 11).
Attach the pilot gas line to the pilot outlet of the gas control
valve and tighten. Connect the thermocouple to the rear of the
gas control valve (see Figure 12). Do not overtighten (fingertight plus 1/4 turn). If using propane/LP gas, see Changing Pilot Orifice, page 12.
Install the inlet fitting into the inlet opening of the gas control
valve (see Figure 13). Use thread sealant on the male pipe threads.
Thread the gas supply fitting to the fireplace gas supply pipe (see
Figure 10). Adjust to most convenient position.
Install the gas flex line to the gas supply fitting. Carefully shape
tube to attach to adapter fitting.
Thermocouple and Line
Pilot and Line
Gas Control Valve
Figure 12 - Gas Control Valve with Thermocouple and Pilot
Gas Line
Gas Control
Valve
Inlet
Opening
Gas Inlet
Fitting
Figure 13 - Installing Inlet Fitting and Gas Connector Tube
109484
INSTALLATION
Optional GA9053A Series ON/OFF Safety Valve/Pilot Kit Assembly (Cont.)
11
11
INSTALLATION
Continued
10. Install thermocouple, pilot, and ignitor onto valve cover as shown
in Figure 14. Use the provided screws.
11. Push the control rod extension onto the “D” shaped control rod
through the center hole in the cover.
12. Install the position decal and control knob making sure to align
the marks with the correct stop positions of the gas control.
Pilot position will allow the knob to push in about 1/2". Align
the decals in the pilot position.
Screw
Ignitor
Thermocouple
3.
Replace front burner inlet fitting and natural gas injector with
the provided propane/LP fitting and injector (propane/LP fitting
has holes). See chart, Figure 4 on page 7 and Figure 16. Using
thread sealant (resistant to the action of propane/LP gas) on larger
end of fitting, screw the burner inlet fitting through the hole and
into the burner manifold. Tighten using a 7/8" wrench.
4. Apply thread sealant compound to the 3/8" male threads of the
burner inlet fitting. Thread the manifold block (see Figure 15)
onto the burner inlet fitting. Use the bottom hole of the block.
5 . Apply thread sealant to the 1/8" brass pipe nipple and thread it into
the manifold block (see Figure 15). Tighten with a 7/16" wrench.
6. Slip the air restrictor over the 1/8" pipe nipple. Apply thread
sealant to the male threads and install the rear burner nozzle
provided with the GA9053A (see chart, Figure 4 on page 7)
onto the fitting. Tighten with a 9/16" wrench. Proceed with
step 7, page 9 in Hearth Kit Assembly and Installation.
fire-parts.com
Pilot
Rear Burner Nozzle
Air Restrictor
Pipe
Nipple
Valve
Cover
Manifold
Block
Front
Burner
Burner Inlet
Fitting
Control Knob
Piezo Ignitor
Control Rod
Extension
Figure 15 - Kit Assembly
Injector for
Natural Gas
Injector for
Propane/LP Gas
Figure 14 - Installing Cover, Control Knob, and Piezo Ignitor
Propane/LP Gas Conversion
To convert to propane/LP gas, the two main burner orifices and pilot
orifice must be replaced.
Main Burner Orifices
Note: Be sure all pipe threaded connections are tight, and have
thread compound to prevent leaks. Be sure to use the correct orifice
for your unit. See chart on page 7.
1. Remove the burner inlet fitting from the front burner manifold
(installed in burner pan). See Figure 15.
2. Make sure ports on front burner manifold are facing the front
(open side) of burner pan. Refit if needed.
109484
NATURAL GAS
BURNER INLET
FITTING
PROPANE/LP
BURNER INLET
FITTING
Figure 16 - Burner Inlet Fitting with Injectors
12
INSTALLATION
Optional GA9053A Series ON/OFF Safety Valve/Pilot Kit Assembly (Cont.)
Testing Burner for Leaks
Adding Pan Material
Installing the Ember Bed and Logs
INSTALLATION
Continued
Changing Pilot Orifice
ADDING PAN MATERIAL
The pilot is provided with a natural gas orifice installed. For
propane/LP gas you must remove it and replace it with an propane/
LP orifice. The hardware kit contains an propane/LP orifice with a
red stripe for converting the pilot.
1. Gently loosen and remove the pilot line connection from the
bracket (see Figure 17).
2. Replace the injector (see Figure 17) with the propane/LP pilot
injector with the red stripe.
3. Replace and tighten the pilot line to the bracket.
4. Continue with step 3 under Natural Gas Installation, page 10.
1.
2.
Open the bag of ash bed material (vermiculite) and spread it
evenly across the burner pan to the top. You may overflow the
front and sides of the pan to cover the entire pan and connecting hardware.
Open the glowing embers and evenly cover the ash bed material (vermiculite) in the burner pan.
INSTALLING THE EMBER BED AND LOGS
(Canyon Split Log Set Shown)
1.
2.
Place the ember bed (included with burner set) over log grate
as shown in Figure 18.
Position the back log flush against back of ember bed as shown
in Figure 19.
fire-parts.com
Pilot Injector
Grate
Ember Bed
Figure 17 - Installing Propane/LP Pilot Orifice
TESTING BURNER FOR LEAKS
1.
Generously apply noncorrosive leak detection fluid to all joints.
WARNING: Never check for gas leaks with open
flame.
2.
3.
4.
5.
Light the burner with the shutoff valve no more than half open
and holding a match slightly in front of the pan (see Lighting
Instructions, page 13).
Inspect all connections for bubbles, raw gas odor, or flame
from any area other than the burner (leaks). If leaks are detected, shut off the gas valve immediately. Tighten, or reassemble the loose connection(s) using pipe joint compound until
burner system is leak free.
When the burner is tested and leak free, observe the individual
tongues of flame on the burner. Note: The burner design includes more ports on the outside of the bar. Make sure that all
ports are clear and producing flame evenly across the burner. If
any ports appear blocked, clear them by removing the burner
manifold and reaming the ports with a modified paper clip or
other suitable tool.
When finished testing, turn the gas shutoff valve OFF to extinguish all flames.
Figure 18 - Installing Ember Bed
Figure 19 - Installing Back log
109484
INSTALLATION
Installing the Ember Bed and Logs (Cont.)
OPERATING APPLIANCE
13
13
For Your Safety Read Before Lighting
Lighting Instructions
Gas Shutoff Valve Operation
INSTALLATION
OPERATING APPLIANCE
Continued
3.
4.
FOR YOUR SAFETY
READ BEFORE LIGHTING
Place the middle layer of logs as shown in Figure 20. Notice
the grove in the back log for placement of log to the far right.
Adequate space should be left between logs and ember bed
for flames.
Place the top layer of logs as shown in Figure 21.
WARNING: Keep flue open when operating unit.
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is heavier
than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
fire-parts.com
LIGHTING
INSTRUCTIONS
Figure 20 - Installing Logs
1.
2.
3.
4.
5.
Figure 21 - Installing Logs
STOP! Read the safety information, above.
Turn the gas shutoff valve to OFF.
Wait five (5) minutes to clear out any gas. If you then smell
gas STOP! Follow the safety information above. If you don't
smell gas, go on to the next step.
Light a match and lay it on top of the "U" shaped burner
near the edge of the cover on the right side of the pan.
Slowly turn the gas shutoff valve ON until the burner ignites. If the burner doesn’t ignite within 10 seconds with
the match burning, turn the shutoff valve OFF and repeat
steps 1 through 4 again.
GAS SHUTOFF
VALVE OPERATION
Flame Adjustment
Adjust the flame ON/OFF by turning the gas shutoff valve
counterclockwise
to open or clockwise
to close,
as necessary.
Shutting Off Appliance
Turn gas shutoff valve clockwise
109484
to the OFF position.
14
OPERATING APPLIANCE
Curing Logs
Operating Instruction for GA9053A
To Turn Off Gas to Appliance
CLEANING AND MAINTENANCE
OPERATING APPLIANCE
Continued
8.
Keep control knob pressed in for 30 seconds after lighting
pilot. After 30 seconds, release control knob.
Note: If pilot goes out, repeat steps 3 through 7.
Turn control knob counterclockwise
to the ON
position. Burner should light. If burner does not light, call
a qualified service person.
Control Knob
Pilot
Ignitor
ON
On
OFF
FROM "PILOT" POSITION
SLIGHT PUSH TO
TURN OFF
PULL PUSH
ON
Off
ON
OPERATING
INSTRUCTIONS FOR
GA9053A
OFF
FROM "PILOT" POSITION
SLIGHT PUSH TO
TURN OFF
PULL PUSH
OFF
During the 2-3 hour appliance break-in period, you may detect
an odor from the appliance as the various paints and compounds used in the manufacturing of this log set cure. This is a
normal and temporary situation that is not cause for alarm.
However, you may want to provide extra ventilation to the room
during this time.
To ensure proper curing of the logs:
• Ignite a 2" flame and maintain it for 1 hour.
• Burn the logs in consecutive 1 hour periods raising the flame
an additional 2" to full flame height for a total of three hours.
7.
FROM "PILOT" POSITION
SLIGHT PUSH TO
TURN OFF
PULL PUSH
CURING LOGS
fire-parts.com
Note: Operation instructions for GA9153A Remote Ready
Valve/Pilot Kit will be included with the Kit.
1. STOP! Read the safety information, page 13.
2. Make sure equipment shutoff valve is fully open.
3. Press in and turn control knob clockwise
to the
OFF position.
4. Wait five (5) minutes to clear out any gas. Then smell for gas
around log set and near floor. If you smell gas, STOP! See
Safety Information, page 2 and Air For Combustion And Ventilation, pages 4 through 6. If you don’t smell gas, go to the
next step.
5. Turn control knob counterclockwise
to the PILOT
position and press in. Keep control knob pressed in for five
(5) seconds.
Note: You may be running this log set for the first time
after hooking up to gas supply. If so, the control knob may
need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.
• If control knob does not pop up when released, contact a
qualified service person or gas supplier for repairs.
6. With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the
rear of the front burner. If needed, keep pressing ignitor
button until pilot lights.
Note: If pilot does not stay lit, contact a qualified service
person or gas supplier for repairs. Until repairs are made,
light pilot with match.
Figure 22 - Ignitor and Control Knob
Pilot
Thermocouple
Figure 23 - Thermocouple and Pilot
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Appliance
1.
2.
Turn control knob clockwise
to the PILOT position.
Press in and turn control clockwise
to the OFF
position.
Shutting Off Burner Only (pilot stays lit)
Turn control knob clockwise
to the PILOT position.
CLEANING AND
MAINTENANCE
• Keep the area around the log set clean and clear of debris.
• Occasionally, you may use a soft bristle brush to clean logs.
• Once every year a qualified agency or certified chimney sweep
should examine and clean the venting system of the fireplace.
109484
TROUBLESHOOTING
15
15
TROUBLESHOOTING
Note: All troubleshooting items are listed in order of operation.
WARNING: Turn off log set and let cool before
servicing. Only a qualified service person should
service and repair log set.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Log set is smoking/sooting excessively
(Note: It is natural and unavoidable for
vented gas log sets to produce moderate
levels of carbon (soot) where flames
contact the logs. This is especially true
with propane/LP gas.)
1. Poor fuel quality
5. Excessive gas supply/pressure
1. Contact local natural or propane/LP gas
company
2. Adjust damper wide open and/or have
fireplace and venting professionally
cleaned and checked
3. Separate the logs to allow more flame
passage
4. Remove any foreign items from the
flame pattern and/or check for proper
orifice sizing
5. Preheat flue in very cold weather
Burner is excessively noisy
(Note: The movement and combustion of gas
will create low, unavoidable levels of noise.)
1. Passage of air/gas across irregular surfaces
1. Relieve any tight bends or kinks in gas
supply line
Burner flame is too low or too high
1. Incorrect gas supply or pressure
2. Blocked burner orifice or burner manifold ports
3. Improper burner orifice size
1. Check for proper gas supply pressure
2. Free burner orifice and manifold ports
of any burrs, paint, or other blockage
3. Verify proper burner orifice sizing (see
Figure 4, page 7)
When ignitor button is pressed, there is no
spark at pilot (GA9053A Only)
1. Ignitor electrode not connected to ignitor cable
2. Ignitor cable pinched or wet
1. Reconnect ignitor cable
2. Fireplace venting system not drafting
properly
3. Excessive flame impingement or
blockage
4. Improper fuel/air mixture
fire-parts.com
3. Bad ground on piezo ignitor
4.
5.
6.
7.
109484
Broken ignitor cable
Bad piezo ignitor
Ignitor electrode broken
Ignitor electrode positioned wrong
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Scrape away paint on bracket for better
contact with ground on piezo ignitor
4. Replace ignitor cable
5. Replace piezo ignitor
6. Replace electrode
7. Reposition electrode
TROUBLESHOOTING
16
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed, there is
spark at pilot but no ignition (GA9053A
Only)
1. Gas supply turned off or equipment
shutoff valve closed
2. Control knob not in PILOT position
3. Control knob not pressed in while in
PILOT position
4. Air in gas lines when installed
1. Turn on gas supply or open equipment
shutoff valve
2. Turn control knob to PILOT position
3. Press in control knob while in PILOT
position
4. Continue holding down control knob. Repeat igniting operation until air is removed
5. Adjust pilot flame for approximately
2" blue flame
6. Clean pilot (see Cleaning and Maintenance, page 14) or replace pilot assembly
7. Replace gas control
5. Pilot adjustment screw closed
6. Pilot is clogged
7. Low gas pressure
Pilot lights but flame goes out when control
knob is released (GA9053A Only)
1. Control knob not fully pressed in
2. Control knob not pressed in long enough
1. Press in control knob fully
2. After pilot lights, keep control knob
pressed in 30 seconds
3. Fully open equipment shutoff valve
4. A) Contact local natural or propane/LP
gas company
fire-parts.com
3. Equipment shutoff valve not fully open
4. Pilot flame not touching thermocouple,
which allows thermocouple to cool,
causing pilot flame to go out. This problem could be caused by one or both of
the following:
A) Low gas pressure
B) Dirty or partially clogged pilot
5. Thermocouple connection loose at control valve
6. Thermocouple damaged
7. Control valve damaged
Burner does not light after pilot is lit
(GA9053A Only)
1. Burner orifice clogged
2. Inlet gas pressure is too low
3. Burner orifice diameter is too small
4. Thermocouple leads disconnected or improperly connected
Delayed ignition burner (GA9053A Only)
White powder residue forming within burner
box or on adjacent walls or furniture
1. Pilot flame needs adjusting
B) Clean pilot (see Cleaning and Maintenance, page 14) or replace pilot assembly
5. Hand tighten until snug, then tighten
1/4 turn more
6. Replace thermocouple
7. Replace control valve
1. Clean burner orifice
2. Contact local natural or propane/LP gas
company
3. Replace burner orifice
4. Reconnect leads
2. Wrong pilot orifice
1. Adjust pilot flame for approximately
2" blue flame
2. Replace pilot orifice set
1. When heated, vapors from furniture polish, wax, carpet cleaners, etc. may turn
into white powder residue
1. Turn heater off when using furniture
polish, wax, carpet cleaners, or similar
products
109484
TROUBLESHOOTING
17
17
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating log set where impurities in air exist may create odors. Cleaning
supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles,
etc., create fumes. These fumes may mix with combustion air and create odors. These odors
will disappear over time.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Log set produces a clicking/ticking noise
just after burner is lit or shut off
1. Metal expanding while heating or contracting while cooling
1. This is common with most log sets. If
noise is excessive, contact qualified service person
Log set produces unwanted odors
1. Log Set burning vapors from paint, hair
spray, glues, cleaners, chemicals, new
carpet, etc. (See IMPORTANT statement above)
2. Gas leak. See Warning statement at
top of page
1. Open flue to maximum. Stop using odor
causing products while log set is running
Gas odor even when control knob is in OFF
position
1. Gas leak. See Warning statement at
top of page
2. Control valve defective
1. Locate and correct all leaks (see Checking Gas Connections, pages 8 and 9)
2. Replace control valve
Gas odor during combustion
1. Gas leak. See Warning statement at
top of page
2. Locate and correct all leaks (see Checking Gas Connections, pages 8 and 9)
fire-parts.com
109484
2. Locate and correct all leaks (see Checking Gas Connections, pages 8 and 9)
ILLUSTRATED PARTS BREAKDOWN
18
BVTR18
ILLUSTRATED PARTS
BREAKDOWN
BVTR18
20
22
24
19
21
25
23
fire-parts.com
2
4
1
5
6
5
3
15
17
18
8
9
14
12
13
26
7
16
10
11
109484
PARTS LIST
BVTR18
PARTS LIST
BVTR18
This list contains replaceable parts used in your log set. When
ordering parts, follow the instructions listed under Replacement
Parts on page 22 of this manual.
KEY PART
NO. NUMBER
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
ODS Nut
Rear Burner
Burner Clip
Log Grate
Screw, 10-16 x .38
Burner Bracket
Front Burner
Burner Pan
Nozzle
Natural Gas Injector
Brass Air Mixer - Natural Gas
1/8 Hex Nipple
Manifold Block
Air Restrictor
Valve Cover
Brass Elbow Flare Fitting
Brass 3/8 FLR x 1/2 FPT Adapter
Gas Line - 10" Flex
Ember Bed
Top Log VR-11/VC
Top Log VCR-9/VS
Top Log CS-16/VS
Top Log VR-10Y/VS
Top Log CS-13Y/VS
Bottom Log CSB-18/VS
Manifold Plug
098249-01
901752-02
102843-01
901246-01
098304-01
901762-01
901754-02
901753-02
901750-01
901064-05
901066-01
901761-01
901760-01
901751-01
901756-01
901056-01
901058-01
101628-01
901769-02
901580-02
901587-04
901528-04
901579-02
901676-05
901530-03
901759-01
QTY.
2
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
fire-parts.com
PARTS AVAILABLE — NOT SHOWN
901036-01
109462-04
901242-01
CDABKA
GA9350A
109484
RADCO GEN Rating Plate
Rating Information Plate
Damper Clamp
Decorative Ash Bed Control Cover
Ornamental Grate Enhancer
1
1
1
1
1
19
19
ILLUSTRATED PARTS BREAKDOWN
20
BVTR24
ILLUSTRATED PARTS
BREAKDOWN
BVTR24
20
25
22
19
21
26
24
fire-parts.com
23
2
4
1
5
6
5
3
15
17
18
8
9
14
12
13
27
7
16
10
11
109484
PARTS LIST
BVTR24
PARTS LIST
BVTR24
This list contains replaceable parts used in your log set. When
ordering parts, follow the instructions listed under Replacement
Parts on page 22 of this manual.
KEY PART
NO. NUMBER
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
ODS Nut
Rear Burner
Burner Clip
Log Grate
Screw, 10-16 x .38
Burner Bracket
Front Burner
Burner Pan
Nozzle
Natural Gas Injector
Brass Air Mixer - Natural Gas
1/8 Hex Nipple
Manifold Block
Air Restrictor
Valve Cover
Brass Elbow Flare Fitting
Brass 3/8 FLR x 1/2 FPT Adapter
Gas Line - 10" Flex
Ember Bed
Top Log VR-11/VC
Top Log VCR-9/VS
Top Log CS-16/VS
Top Log CS-18/VS
Top Log VR-10Y/VS
Top Log VS-12
Bottom Log CS-24/VS
Manifold Plug
098249-01
901752-01
102843-01
901246-02
098304-01
901762-01
901754-01
901753-01
901750-01
901064-01
901066-01
901761-01
901760-01
901751-01
901756-01
901056-01
901058-01
101628-01
901769-01
901580-02
901587-04
901528-04
901540-04
901579-02
901588-01
901532-03
901759-01
QTY.
2
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
fire-parts.com
PARTS AVAILABLE — NOT SHOWN
901036-01
109462-05
901242-01
CDABKA
GA9360A
109484
RADCO GEN Rating Plate
Rating Information Plate
Damper Clamp
Decorative Ash Bed Control Cover
Ornamental Grate Enhancer
1
1
1
1
1
21
21
22
REPLACEMENT PARTS
ACCESSORIES
REPLACEMENT PARTS
Note: Use only original replacement parts. This will protect your
warranty coverage for parts replaced under warranty.
PARTS UNDER WARRANTY
Contact Barbeques Galore at 1-800-673-5206. When calling
Barbeques Galore, have ready
• your name
• your address
• model and serial numbers of your fireplace
• how fireplace was malfunctioning
• type of gas used (propane/LP or natural gas)
• purchase date
Usually, we will ask you to return the defective part to the factory.
PARTS NOT UNDER WARRANTY
Contact Barbeques Galore at 1-800-673-5206. When calling
Barbeques Galore, have ready
• model number of your fireplace
• the replacement part number
RECEIVER AND HAND-HELD REMOTE CONTROL KIT - GHRC Series
For all models. Allows the gas log set to be turned on and off by
using a hand-held remote control. Valve/Pilot Kit GA9153A must
be used with this remote.
ON/OFF SAFETY VALVE/PILOT KIT - GA9053A
(Not Shown)
fire-parts.com
For all models. Required for Propane/LP installation.
REMOTE READY VALVE/PILOT KIT - GA9153A
(Not Shown)
ACCESSORIES
For all models.
Purchase these fireplace accessories from your local dealer. If they can
not supply these accessories, call Barbeques Galore at 1-800-673-5206
for information. You can also write to the address listed on the back page
of this manual.
(Not Shown)
PINE CONES - GA9650A
For all models. Use for additional decoration only. Carton of 6
Boxes (3 pine cones per box).
ASH BED MATERIAL (Vermiculite) - GA9750A
(Not Shown)
For all models. Carton of 6.
GLOWING EMBERS - GA9950A
(Not Shown)
For all models. Use for firebox decoration only.
SILICA SAND - GA9850A
EQUIPMENT SHUTOFF VALVE GA5010
For all models. Equipment shutoff valve with 1/8" NPT tap. Fits 1/2"
NPT pipe.
(Not Shown)
For all models. Use for firebox decoration only. Carton of 6.
LAVA ROCK - GA6067A
(Not Shown)
For all models. Use for firebox decoration only.
109484
NOTES
23
23
NOTES
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
fire-parts.com
109484
24
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We make
no other warranty, expressed or implied.
LIMITED WARRANTY
BARBEQUES GALORE VENTED GAS LOGS
Barbeques Galore warrants this product to be free from defects on burner system for four (4) years and logs for a lifetime from the date of first
purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions. To make
a claim under this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this log set to proper
operating condition and an allowance for labor when provided by a Barbeques Galore Authorized Service Stores. Warranty part(s) MUST be obtained
through authorized dealers of this product and/or Barbeques Galore who will provide original factory replacement parts. Failure to use original factory
replacement parts voids this warranty. The log set MUST be installed by a qualified installer in accordance with all local codes and instructions
furnished with the unit.
fire-parts.com
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a
result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and
any and all such other costs related to repairing a defective log set will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS
EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
TO FOUR (4) YEARS ON BURNER SYSTEM AND A LIFETIME ON LOGS FROM THE DATE OF FIRST PURCHASE; AND BARBEQUES
GALORE’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND BARBEQUES GALORE SHALL NOT
BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages,
so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
15041 Bake Parkway
Suite A
Irvine, California 92618
109484 01
NOT A UPC
109484-01
Rev. A
09/01
109484
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising