User manual | Phase-Adaptive Power Module

Lutron
Phase-Adaptive Power Module
Power Modules
369356d 1 10.14.16
Phase-Adaptive Power Module
Description
•Provides capability for a zone on a GRAFIK Eye control
unit (or other product) to dim a fully loaded circuit of
lighting.
•May be used to control incandescent, electronic lowvoltage, magnetic low-voltage, and neon / cold cathode
lighting sources, as well as Lutron Tu-Wire fluorescent
dimming ballasts.
•Automatically selects leading-edge or trailing-edge
dimming for low-voltage transformers.
•Provides power and dimming for one zone.
•Up to 3 power modules may be wired on a single
GRAFIK Eye zone.
•Models available for 120 V~ control power.
•Models available for 120 V~ or 120 - 277 V~ load
power.
•Not for use with non-dim loads.
Works with 120 V~ versions of:
•GRAFIK Eye QS control units 1
•GRAFIK Eye 3000 Series control units 2
•LP, LCP, and GP dimming panels 2
•HomeWorks and HomeWorks QS remote power
panels**
Models and Capacities
Model Number
PHPM-PA-DV-WH
PHPM-PA-120-WH
1
2
Control Power
120 V~
120 V~
Load Power
120 –277 V~
120 V~
Capacity
16 A
16 A
Set to power module load type
Set to incandescent load type
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
Lutron
Phase-Adaptive Power Module
Power Modules
369356d 2 10.14.16
Specifications
Regulatory Approvals
•UL® Listed
• CSA certified
• NOM certified
•Complies with requirements for use in other spaces
used for environmental air (plenums) per
NEC® 2014 300.22(C)(3)
Power
•Control voltage: 120 V~
•Load voltage: 1
20 V~ only for PHPM-PA-120-WH
120 –277 V~ for PHPM-PA-DV-WH
•Capacity: F
ull 16 A
120 V~: 1920 W
120 –277 V~: 1920 – 4432 W
•Frequency: 50 / 60 Hz, phase-to-neutral.
•Load (output) power: Phase independent of control
device / control voltage.
Sources / Load Types
•Operates these sources with a smooth continuous
Square Law dimming curve:
– Incandescent (tungsten)
– Halogen
– Magnetic low-voltage transformer (iron core)
– Electronic (solid-state) low-voltage transformer (must
be manufacturer approved for reverse-phase control
dimming)
– Neon / Cold cathode
– Lutron Tu-Wire fluorescent dimming ballasts
• Incandescent and electronic low-voltage sources
may be controlled on the same circuit / control zone.
Up to 30% of the unit’s capacity may be used for
incandescent lighting.
• Incandescent and magnetic low-voltage sources may
NOT be controlled on the same circuit / control zone.
•PHPM-PA not for use with non-dim loads. Use
switching power module (PHPM-SW-DV-WH) for nondim loads.
•Minimum load on power module is 10 W.
•Output must be directly connected to the load. Load
side switching is not recommended.
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Key Design Features
•Automatically selects between forward phase / leading
edge (e.g., magnetic low-voltage) and reverse phase /
trailing edge (e.g., electronic low-voltage) dimming /
output based on connected load.
•Patented RTISS circuitry compensates in real time
for incoming line voltage variations: Compensates for
+/-2% change in RMS voltage / cycle and +/-2% Hz
change in frequency/second.
•Provides air-gap off.
•Module protects itself during most temporary overcurrent and over-voltage conditions.
•Two LEDs on front of unit provide diagnostic
information (visible when faceplate is removed).
Terminals
•Each terminal accepts up to two 12 AWG
(2.5 mm2) wires.
Environment
•32 °F to 104 °F (0 °C to 40 °C). Relative humidity
less than 90% non-condensing.
•Indoor use only.
•Maximum heat output of module: 135 BTU / hour.
Mounting
•Surface- or recess-mount.
Page
Lutron
Phase-Adaptive Power Module
Power Modules
369356d 3 10.14.16
Dimensions
All dimensions shown as: in (mm)
1.2 (30.5)
1.4 (35.5)
5.1
(129.5)
6.3
(160)
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
Lutron
Phase-Adaptive Power Module
Power Modules
369356d 4 10.14.16
Mounting
•Mount in 2-gang U.S. wallbox 3.5 in (89 mm) deep or
4 in x 4 in (102 mm x 102 mm) junction box 2.1 in
(53 mm) deep.
•Indoor use only.
•This device generates heat; mount only where ambient
temperature is 32 °F to 104 °F (0 °C to 40 °C).
•Mount with arrows facing up to ensure adequate
cooling.
Mount to 2-gang U.S. wallbox
•Allow 4.5 in (114 mm) above and below unit and
between faceplates when mounting several in a
vertical layout.
•Mount so line (mains) voltage wiring is at least 6 ft
(1.8 m) from sound or electronic equipment and
wiring.
•Mount within 7° of true vertical.
Mount to 4 in x 4 in (102 mm x 102 mm),
2.1 in (53 mm) deep U.S. junction box
Mount to 4 in x 4 in (102 mm x 102 mm), 2.1 in (53 mm) deep
U.S. junction box with barrier
(for 277 V~ model if required by local electrical code)
Barrier
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
Lutron
Phase-Adaptive Power Module
Power Modules
369356d 5 10.14.16
Wiring
•Pull 12 AWG (2.5 mm2) copper (Cu) wires [167 °F (75 °C) minimum] for input power and load circuit.
•Strip 1/2 in (12 mm) insulation from wires before connecting.
•Run separate neutral for load circuit - no common neutrals.
•May be used with GFI breaker protected loads. Load circuit wiring (from GFI breaker to power module to
load) must be run in its own non-metallic conduit, or nuisance tripping may occur. Maximum 100 ft
(30.5 m) between power module and load.
•May be used with AFI breaker protected loads. Maximum load on AFI circuit is 1000 W. Exceeding 1000 W may
cause nuisance tripping of AFI breaker.
Single Power Feed
The power module may be on the same circuit as the control unit only if the total load does not exceed the
rating of the breaker.
GRAFIK Eye QS
Circuit breaker
120 V~
1 2 3 4 5 6 L N
L/H
N
Wire to appropriate
zone
H/L
N
Load
120 V~
Zone in
Control Neutral
DH
Legend
L /H
Line / Hot
NNeutral
SH
Switched Hot
DH
Dimmed Hot
Ground
Not Used
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
Lutron
Phase-Adaptive Power Module
Power Modules
369356d 6 10.14.16
Wiring
(continued)
Multiple Power Feeds
The load breaker may be on a different phase than the control breaker.
GRAFIK Eye QS
1 2 3 4 5 6 L N
N
120 V~
L/H
Wire to appropriate
zone
Control breaker
Load breaker
H/L
N
L/H
N
Load wiring
1
Load
Zone in
Control Neutral
DH
Legend
L / H
Line / Hot
NNeutral
SH
Switched Hot
DH
Dimmed Hot
Ground
Not Used
1
Load feed: 120 V~ for PHPM-PA-120-WH; 120 – 277 V~ for PHPM-PA-DV-WH
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
Lutron
Phase-Adaptive Power Module
Power Modules
369356d 7 10.14.16
Wiring
(continued)
Multiple Power Modules to a Single GRAFIK Eye Zone
Shown with separate feeds for control and loads. All breakers must be turned off prior to installing or servicing
the modules. Up to 3 power modules may be wired to a single zone.
GRAFIK Eye QS
1 2 3 4 5 6 L N
Wire to appropriate zone
N
L/H
120 V~
Control breaker
Load breaker
L/H
H/L
N
N
Load wiring 1
for Power
Module #1
Load
Zone in
Control Neutral
DH
Load breaker
L/H
H/L
N
N
Load wiring 1
for Power
Module #2
Load
Zone in
Control Neutral
DH
Load breaker
H/L
N
L/H
N
Load wiring 1
for Power
Module #3
1
Load
Zone in
Control Neutral
DH
Load feed: 120 V~ for PHPM-PA-120-WH; 120 – 277 V~ for PHPM-PA-DV-WH
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
Lutron
Phase-Adaptive Power Module
Power Modules
369356d 8 10.14.16
Wiring
(continued)
Wiring a Power Module to an LP, LCP, GP, or HomeWorks Panel
Up to three 3-wire fluorescent power modules may be wired to an output of a 120 V~ LP or LCP panel. The
load type for the output must be set as Eco-10 or Hi-lume fluorescent load type on the panel’s circuit selector
(for an LP or GP panel), controller (for an LCP panel), or HomeWorks software (for a HomeWorks panel).
Wire to appropriate output
Load
wiring1
L/H
N
H/L
N
Load
DH
Zone In
Control
Neutral
Dimmed
Hot
(1) 14 to 10 AWG 2
(2.0 to 4.0 mm ) (1) 14 to 10 AWG (2.0 to 4.0 mm2) Neutral
DH
DH
DH
DH
H
N
N
N
N
N
Load feed: 120 V~ if used with PHPM-PA-120-WH power module;
120 – 277 V~ if used with PHPM-PA-DV-WH power module
1
)Lutron, Lutron, Eco-10, GRAFIK Eye, Hi-lume, HomeWorks,
and Tu-Wire are trademarks of Lutron Electronics Co., Inc.,
registered in the U.S. and other countries.
NEC is a registered trademark of National Fire Protection
Association, Quincy, Massachusetts. © 2016 Lutron Electronics
Co., Inc.
UL and the UL logo are trademarks of UL LLC.
®
Job Name:
Job Number:
120 V~ Branch Circuit
Breakers
Neutral Lug
Power (Line / Hot)
(3) 14 to 2/0 AWG (2.0 to 70 mm2)
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Neutral (1) 14 to 2/0 AWG (2.0 to 70 mm2)
Page

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project