NCR 6632 ATM

NCR 6632 ATM
NCR 6632 ATM
Site Preparation
B006-6585-A000
0907
FEDERAL COMMUNICATIONS COMMISSION (FCC) RADIO FREQUENCY
INTERFERENCE STATEMENT
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
Canadian Class A Device Declaration
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la
classe A prescrites dans le Réglement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
Information to User
This equipment must be installed and used in strict accordance with the manufacturer’s instructions. However, there is no guarantee that
interference to radio communications will not occur in a particular commercial installation. If this equipment does cause interference,
which can be determined by turning the equipment off and on, the user is encouraged to consult an NCR service representative immediately.
CAUTION
NCR Corporation is not responsible for any radio or television interference caused by unauthorised
modifications of this equipment or the substitution or attachment of connecting cables and equipment
other than those specified by NCR. Such unauthorized modifications, substitutions, or attachments may
void the user’s authority to operate the equipment. The correction of interference caused by such
unauthorized modifications, substitutions, or attachments will be the responsibility of the user.
The ATM complies with the following Electromagnetic Compatibility (EMC) directives and standards for IT equipment:
•
•
2004/108/EC EMC Directive.
93/68/EEC ‘CE Marking Directive’.
For further information, refer to the Electromagnetic Compatibility (EMC) and Safety section.
NOTICE
This is a contractual document. It contains important warnings and confers important legal rights and obligations. You are advised to
read it carefully.
It is the responsibility of the customer to assure that all installation preparations are complete and in compliance with all specifications
and requirements of NCR and all applicable national, state, or local codes, regulations and laws.
The product described in this book is a licensed product of NCR Corporation.
NCR is a trademark of NCR Corporation.
Other product names mentioned in this publication may be trademarks or registered trademarks of their respective companies and are
hereby acknowledged.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become available.
NCR, therefore, reserves the right to change specifications without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances,
photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office
for information that is applicable and current.
© 2007
By NCR Corporation, Dayton, Ohio U.S.A.
http://www.ncr.com
All Rights Reserved
Table of Contents
NCR 6632 ATM Site Preparation
INTRODUCTION ...............................................................................................................1
How to Use This Site Preparation Bookset ....................................................................2
Purpose and Audience ....................................................................................................2
Site Compliance ..............................................................................................................2
Customer Responsibilities ..............................................................................................3
Product Identification .....................................................................................................4
PACKAGE DIMENSIONS.................................................................................................5
Manoeuvring the ATM Into Position..............................................................................6
ATM DIMENSIONS...........................................................................................................7
Privacy Panels.................................................................................................................7
Front Access ...................................................................................................................8
Rear Access.....................................................................................................................9
UL Security Enclosure ...............................................................................................9
CEN Security Enclosure ..........................................................................................10
ACCESS FOR ALL...........................................................................................................11
Height and Depth to Main Facia Items .........................................................................11
Topmost Viewable Facia Item .................................................................................13
Facia Item Locations for Voice Guidance ....................................................................14
Task Lighting ................................................................................................................15
Wheelchair Clearance ...................................................................................................15
INSTALLATION AND SERVICE CLEARANCES........................................................16
Important Notice to Users ........................................................................................16
Recommended Clearances............................................................................................17
Front Access.............................................................................................................17
Rear Access..............................................................................................................18
Minimum Clearances ....................................................................................................19
Front Access.............................................................................................................19
Rear Access..............................................................................................................20
Top-box Clearances ......................................................................................................21
Hot Air Outlets - Front Access .....................................................................................22
Hot Air Outlets - Rear Access ......................................................................................23
B006-6585-A000
i
REQUIREMENTS FOR THE FLOOR.............................................................................24
Floor Covering ..............................................................................................................24
Floor Loading ...............................................................................................................24
BOLT HOLE LOCATIONS .............................................................................................25
Front Access .................................................................................................................25
UL Security Enclosure Bolt Hole Locations............................................................25
CEN Security Enclosure Bolt Hole Locations .........................................................26
Rear Access...................................................................................................................27
UL Security Enclosure Bolt Hole Locations............................................................27
CEN Security Enclosure Bolt Hole Locations .........................................................28
SECURITY BOLTS ..........................................................................................................29
VIDEO CAMERA.............................................................................................................30
Ambient Lighting..........................................................................................................30
Internal Space Constraint for Fitting a Third-Party Video Camera..............................31
ii
B006-6585-A000
NCR 6632 ATM Site Preparation
Table of Contents
NCR 6632 ATM Site Preparation
INTRODUCTION
The NCR 6632 Automated Teller Machine (ATM) is a freestanding interior ATM that is
available in front or rear access variants.
In all illustrations within this manual, the front access will be used, except where the text
relates specifically to the rear access.
B006-6585-A000
1
NCR 6632 ATM Site Preparation
How to Use This Site Preparation Bookset
The site preparation is part of the NCR 6632 ATMs Site Preparation Bookset. It acts both
as a specifications book, and also as a gateway to the other books in the bookset, which
are:
Electrical and Protection Requirements (B006-6588)
Environmental and Planning Requirements (B006-6587)
Purpose and Audience
This book is intended for architects and those responsible for preparing a site prior to the
arrival of the ATM.
Site preparation details are given under the following main sections within this book:
Package Dimensions
ATM Dimensions
Access for All
Installation and Service Clearances
Requirements for the Floor
Bolt Hole Locations
Video Camera
Site Compliance
This document contains the information necessary for the preparation of a site conforming
to NCR specifications. It is very important that the site complies with the requirements
specified in this document, because, once the equipment has been installed, deficiencies in
site preparation or the problems caused by these deficiencies are much more difficult to
detect and correct. Further, failure to comply with these requirements or to take proper
steps to protect equipment against risks identified in this document may cause serious
damage to the equipment and to the customer’s business.
In addition to the need to comply with the requirements specified, electrical wiring and
mechanical systems must also comply with all relevant codes, laws and regulations.
It is important that the site be prepared by a customer or his agent who is fully conversant
with the special requirements of electronic equipment. The responsibility for ensuring that
the site is prepared in compliance with this document remains with the customer.
For information and guidance purposes only, a list is provided, in general terms, of those
matters for which the customer is responsible. This list is not intended to be
comprehensive, and in no way modifies, alters, or limits the responsibility of the customer
for all aspects of adequate site preparation.
2
B006-6585-A000
NCR 6632 ATM Site Preparation
NCR staff will be available to answer questions relating to the contents of this document
but, except where:
a
the customer has been notified that a full or partial consultancy service is available
and/or that NCR will be willing to undertake a preliminary or final site survey and
b
the customer shall have entered into a formal contract with NCR for provision of the
same
no comment, suggestion or advice offered or not offered about preparation of the site nor
any inspection of the site whether before or after preparation is to be taken as approval of
the location of the site and equipment or of its preparation and NCR will not be liable in
respect of any comment, suggestion or advice given by its staff or in respect of any failure
to give advice.
Finally, only the customer can know the full extent of damage which may be caused to his
business by reason of failure of the equipment which is to be installed. For this reason it is
the customer’s responsibility to ascertain the extent of any such possible damage to his
existing or planned business, and to effect, full insurance in respect of it.
Customer Responsibilities
The customer must do or provide the following:
When required by NCR, provide the NCR customer service representative with
appropriate drawings that indicate:
Location of the equipment
Site wiring (power and signal, paths and lengths)
Location of other equipment capable of generating electrical noise,
electromagnetic interference, heat, etc.
Make building alterations necessary to meet wiring and other site requirements.
Provide and install all communications cables, wall jacks, special connectors, and
associated hardware.
Provide and install necessary power distribution boxes, conduits, grounds, lightning
protection, and associated hardware.
Make sure all applicable codes, regulations and laws (including, but not limited to,
electrical, building, safety, and health) are met.
Provide and install auxiliary power or other equipment as required.
Provide storage or service areas as required.
Make sure the environmental requirements of the system/unit are met.
B006-6585-A000
3
NCR 6632 ATM Site Preparation
Provide floor coverings and environmental systems that limit or control static
electricity build-up and discharge.
Install the product at a height which meets the accessibility regulations of the relevant
country.
Product Identification
The product is identified by the class number, 6632, and a 4 digit model number, which is
printed on a label fixed inside the top-box of the ATM. The serial number is unique to
each ATM. The tracer number is used to identify where the ATM was built. Please quote
all of the serial and tracer numbers, including the prefix, when making reference to the
ATM.
Model: XXXX
Class: 6632
NCR Global Solutions Ltd.
Serial: XX-XXXXXXXX
Tracer: XX-XXXXX
Vac: XXX
Made in UK
U® L
LISTED
649
Automated Teller Machine
24 Hour Service Level 1
Hz: 50/60
A:X.X
® LR 32207
Electromagnetic Compatibility
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This apparatus does not exceed Class A limits for radio noise emissions set out in the Radio Interference
Regulations of Canada.
Le present appariel n’emet pas de bruits radioelectriques depassant les limites de la classe A prescrites
dans le Reglement sur le brouillage radioelectrique du Canada.
‘’Complies with FDA Radiation Performance Standards, 21 CFR Subchapter J’‘
4
B006-6585-A000
NCR 6632 ATM Site Preparation
PACKAGE DIMENSIONS
The dimensions of a packaged ATM, with and without the carton and lid, are shown
below.
1435 mm
(56.5 in.)
977 mm
(38.5 in.)
1836 mm
(72.3 in.)
1779 mm
(70.0 in.)
957 mm
(37.7 in.)
1405 mm
(55.3 in.)
B006-6585-A000
5
NCR 6632 ATM Site Preparation
Manoeuvring the ATM Into Position
Ensure that doorways and corridors leading to your point of installation are wide enough
to allow the package to pass through, or make arrangements to unpack the ATM in an area
with sufficient access and then move it to the installation site. Also make sure that any
corridors can support the weight of the ATM. Refer to page 24 for the maximum weight of
the ATM and its floor loading.
The following table gives the minimum dimensions for doorways, corridors with right
angle corners and the space required to rotate an ATM on its axis.
Note 1: The dimensions assume the ATM is being moved using equipment that does not
extend beyond the ATM or packaging.
Note 2: A surrounding clearance of 6 mm (0.2 in.) has been allowed in the figures.
Note 3: If privacy panels are fitted, the unpackaged ATM dimensions will increase by
36 mm (1.4 in.) for a corridor with corner and 85 mm (3.3 in.) for rotation about centre. If
the corridor and corner are not wide enough to allow an ATM with privacy panels to pass
through, the panels can be removed and installed later.
A
B
B
C
A Doorway or straight corridor
B Corridor with corner
C Rotation about centre
6
Packaged ATM
(pallet, carton
and lid)
Packaged ATM
(pallet and
carton)
Unpackaged
Front Access
ATM
Unpackaged
Rear Access
ATM
989 mm
(38.9 in.)
1210 mm
(47.6 in.)
1748 mm
(68.8 in.)
969 mm
(38.1 in.)
1185 mm
(46.7 in.)
1712 mm
(67.4 in.)
796 mm
(31.3 in.)
927 mm
(36.5 in.)
1298 mm
(51.1 in.)
796 mm
(31.3 in.)
949 mm
(37.4 in.)
1348 mm
(53.1 in.)
B006-6585-A000
NCR 6632 ATM Site Preparation
ATM DIMENSIONS
The following illustrations show dimensions for ATMs configured with CEN Grade L,
CEN Grade III, CEN Grade IV Spanish Certified and UL 291 Level 1 security enclosures.
Note: Cables enter the ATM through the hole in the base of the ATM security enclosure.
Refer to page 25 for the location of the hole.
Privacy Panels
The illustration below shows the ATM with privacy panels fitted to either side of the facia.
The dimensions are the same for ATMs configured with a CEN Grade L, CEN Grade III,
CEN Grade IV Spanish Certified or UL security enclosure.
1122 mm
(44.2 in.)
1184 mm
(46.6 in.)
575 mm
(22.7 in.)
1324 mm
(52.2 in.)
276 mm
(10.9 in.)
749 mm
(29.5 in.)
Front Access
319 mm
(12.6 in.)
Rear Access
B006-6585-A000
7
NCR 6632 ATM Site Preparation
Front Access
The illustration below shows the dimensions for a front access ATM configured with a
CEN Grade L, CEN Grade III, CEN Grade IV Spanish Certified or UL security enclosure.
803 mm
(31.6 in.)
7 mm
(0.3 in.)
1574 mm
(62.0 in.)
217 mm
(8.5 in.)
44 mm
(1.7 in.)
1020 mm
(40.2 in.)
784 mm
(30.9 in.)
2073 mm
(81.6 in.)
See Note
1575 mm
(62.0 in.)
1570 mm
(61.8 in.)
763 mm
(30.0 in.)
635 mm
(25.0 in.)
3 mm
(0.1 in.)
770 mm
(30.3 in.)
6 mm
(0.2 in.)
43 mm
(1.7 in.)
174 mm
(6.9 in.)
800 mm
(31.5 in.)
779 mm
(30.7 in.)
Note: For ATMs fitted with privacy panels, this dimension is 2141 mm (84.3 in.).
8
B006-6585-A000
NCR 6632 ATM Site Preparation
Rear Access
UL Security Enclosure
The illustration below shows the dimensions for a rear access ATM configured with a UL
security enclosure.
65 mm
(2.5 in.)
7 mm
(0.3 in.)
44 mm
(1.7 in.)
217 mm
(8.5 in.)
1636 mm
(64.4 in.)
1082 mm
(42.6 in.)
784 mm
(30.9 in.)
1570 mm
(61.8 in.)
2073 mm
(81.6 in.)
See Note
1575 mm
(62.0 in.)
763 mm
(30.0 in.)
635 mm
(25.0 in.)
770 mm
(30.3 in.)
217 mm
(8.5 in.)
914 mm
(36.0 in.)
800 mm
(31.5 in.)
37 mm
(1.5 in.)
Note: For ATMs fitted with privacy panels, this dimension is 2141 mm (84.3 in.).
B006-6585-A000
9
NCR 6632 ATM Site Preparation
CEN Security Enclosure
The illustration below shows the dimensions for a rear access ATM configured with a
CEN Grade L, CEN Grade III or CEN Grade IV Spanish Certified security enclosure.
65 mm
(2.5 in.)
7 mm
(0.3 in.)
44 mm
(1.7 in.)
217 mm
(8.5 in.)
1636 mm
(64.4 in.)
1082 mm
(43.0 in.)
784 mm
(30.9 in.)
1570 mm
(61.8 in.)
2073 mm
(81.6 in.)
See Note
1575 mm
(62.0 in.)
763 mm
(30.0 in.)
635 mm
(25.0 in.)
770 mm
(30.3 in.)
217 mm
(8.5 in.)
914 mm
(36.0 in.)
800 mm
(31.5 in.)
Note: For ATMs fitted with privacy panels, this dimension is 2141 mm (84.3 in.).
10
B006-6585-A000
63 mm
(2.5 in.)
NCR 6632 ATM Site Preparation
ACCESS FOR ALL
The ATM has been designed to meet the height and reach requirements of both the ablebodied and the disabled. For wheelchair users, the ATM offers optimised parallel
approach, providing easy access, security and private space if installed according to the
specifications detailed in this document.
Height and Depth to Main Facia Items
The following table gives the height and depth to the main facia items located on the facia.
All the height dimensions are calculated from the base of the ATM.
Facia Item
Height
(from base of ATM)
Depth
(from front of shelf)
A
Cheque Entry
1185 mm
(46.7 in.)
183 mm
(7.2 in.)
B
Coin Exit
1191 mm
(46.9 in.)
178 mm
(7.0 in.)
305 mm (12.0 in.) Touchscreen Display
1105 mm
(43.5 in.)
231 mm
(9.1 in.)
381 mm (15.0 in.) Touchscreen Display
1126 mm
(44.3 in.)
244 mm
(9.6 in.)
305 mm (12.0 in.) Display - 1st FDK
1043 mm
(41.1 in.)
184 mm
(7.2 in.)
381 mm (15.0 in.) Display - 1st FDK
1054 mm
(41.5 in.)
193 mm
(7.6 in.)
305 mm (12.0 in.) Display - 2nd FDK
1014 mm
(39.9 in.)
172 mm
(6.8 in.)
381 mm (15.0 in.) Display - 2nd FDK
1019 mm
(40.1 in.)
174 mm
(6.9 in.)
Cash Exit or Entry
822 mm
(32.4 in.)
152 mm
(6.0 in.)
Envelope Exit or Entry
822 mm
(32.4 in.)
152 mm
(6.0 in.)
No. 5 Key
786 mm
(30.9 in.)
89 mm
(3.5 in.)
I
Audio Jack Plug
900 mm
(35.4 in.)
136 mm
(5.4 in.)
J
Card Reader
1039 mm
(40.9 in.)
152 mm
(6.0 in.)
C
D
E
F
SS
G
H
5
JKL
B006-6585-A000
11
NCR 6632 ATM Site Preparation
K
Receipt
1154 mm
(45.4 in.)
170 mm
(6.7 in.)
L
Statement Exit or Passbook Entry and Exit
1193 mm
(47.0 in.)
193 mm
(7.6 in.)
Barcode Reader
1251 mm
(49.3 in.)
178 mm
(7.0 in.)
Barcode Activation Point
1081 mm
(42.6 in.)
174 mm
(6.9 in.)
Camera
1472 mm
(58.0 in.)
175 mm
(6.9 in.)
M
N
A
B
12
C D E F
H
G
B006-6585-A000
I
J
K L M N
NCR 6632 ATM Site Preparation
Topmost Viewable Facia Item
The following illustration shows the projected angle from the front of the ATM facia to
the topmost viewable facia item.
55°
Statement
B006-6585-A000
13
NCR 6632 ATM Site Preparation
Facia Item Locations for Voice Guidance
C
E
D
F
G
B
H
I
A
Facia Item
Distance from No. 5 Key
Clock Face Position
Cash Exit and/or Entry or Envelope Exit and/
or Entry
152 mm
(6.0 in.)
9
305 mm (12.0 in.) Display - Top left-hand FDK
315 mm
(12.4 in.)
11
381 mm (15.0 in.) Display - Top left-hand FDK
341 mm
(13.4 in.)
11
C
Cheque Entry
457 mm
(18.0 in.)
11
D
Coin Exit
463 mm
(18.2 in.)
11
E
Statement Exit or Passbook Entry and Exit
409 mm
(16.1 in.)
12
F
Receipt Exit
472 mm
(18.6 in.)
1
G
Card Reader
388 mm
(15.3 in.)
2
H
Audio Jack Plug
310 mm
(12.2 in.)
2
I
Cash Exit or
Envelope Exit and/or Entry
177 mm
(7.0 in.)
3
A
B
14
B006-6585-A000
NCR 6632 ATM Site Preparation
Task Lighting
A minimum of 200 LUX is required for task lighting.
Wheelchair Clearance
The following illustration shows the clearance required for wheelchair approach and
turning circle.
1524 mm
(60.0 in.)
1524 mm
(60.0 in.)
B006-6585-A000
15
NCR 6632 ATM Site Preparation
INSTALLATION AND SERVICE CLEARANCES
Important Notice to Users
If it is likely that the ATM will be upgraded with new modules as they become available,
you should use the recommended clearances.
Note: Increasing the area around the ATM will improve service access.
16
B006-6585-A000
NCR 6632 ATM Site Preparation
Recommended Clearances
The following illustrations show the recommended areas required for installing and
servicing the ATM.
Front Access
The illustration below shows the recommended clearance dimensions for a front access
6632 ATM configured with a UL or CEN security enclosure.
460 mm
(18.1 in.)
770 mm
(30.3 in.)
460 mm
(18.1 in.)
48 mm
(1.9 in.)
848 mm
(33.4 in.)
2228 mm
(87.7 in.)
1380 mm
(54.3 in.)
1856 mm
(73.1 in.)
B006-6585-A000
17
NCR 6632 ATM Site Preparation
Rear Access
The illustration below shows the recommended clearance dimensions for a rear access
6632 ATM configured with a UL or CEN security enclosure.
1856 mm
(73.1 in.)
1285 mm
(50.6 in.)
3015 mm
(119.0 in.)
1730 mm
(68.5 in.)
460 mm
(18.1 in.)
18
B006-6585-A000
770 mm
(30.3 in.)
460 mm
(18.1 in.)
NCR 6632 ATM Site Preparation
Minimum Clearances
The following illustrations show the minimum areas required for installing and servicing
the ATM.
Front Access
The illustration below shows the minimum clearance dimensions for a front access 6632
ATM configured with a UL or CEN security enclosure.
58 mm
(2.3 in.)
848 mm
(33.4 in.)
886 mm
(34.9 in.)
48 mm
(1.9 in.)
510 mm
(20.1 in.)
453 mm
(17.8 in.)
300 mm
(11.8 in.)
2228 mm
(87.7 in.)
UL
CENL, CENIII
CENIV
1380 mm
(54.3 in.)
All variants with right
hand Cash Acceptor
or right hand Dispenser
1339 mm
(52.7 in.)
1639 mm
(64.5 in.)
1696 mm
(66.8 in.)
B006-6585-A000
19
NCR 6632 ATM Site Preparation
Rear Access
The illustration below shows the minimum clearance dimensions for a rear access 6632
ATM configured with a UL or CEN security enclosure.
1696 mm
(66.8 in.)
1639 mm
(64.5 in.)
1339 mm
(52.7 in.)
1285 mm
(50.6 in.)
104 mm
(4.1 in.)
453 mm
(17.8 in.)
3015 mm
(119.0 in.)
300 mm
(11.8 in.)
510 mm
(20.1 in.)
1626 mm
(64.0 in.)
UL
CENL, CENIII
CENIV
All variants with right
hand Cash Acceptor
or right hand Dispenser
58 mm
(2.3 in.)
886 mm
(34.9 in.)
20
B006-6585-A000
NCR 6632 ATM Site Preparation
Top-box Clearances
There are three conditions that need to be considered when installing the ATM within an
enclosed area. These conditions are as follows:
1. If you are installing your ATM within the minimum clearance area with a normal
ceiling height above the top-box, the ATM will operate at normal temperature.
2. If you are installing your ATM within the minimum clearance area with a 58 mm
(2.28 in.) clearance above the top-box, the maximum operating temperature will need
to be reduced by 5°C (9°F).
3. If you are installing your ATM within the minimum clearance area with a surround or
enclosure that will sit directly on the top-box, a hot air extraction system will need to
be installed. Any such system should be sourced locally. Refer to the illustrations on
page 22 and page 23 for dimensions of the hot air outlet.
Note: Any surround or enclosure that sits on top of the top-box must be self
supporting.
For details of the ATM’s operating temperature range, refer to the Environmental and
Planning Requirements (B006-6587) book.
58 mm
(2.28 in.)
Top-box
A
622 mm
(24.5 in.)
B
B006-6585-A000
622 mm
(24.5 in.)
C
Hot Air
Outlet
21
NCR 6632 ATM Site Preparation
Hot Air Outlets - Front Access
The illustration below shows the position of the hot air outlets on the rear of the front
access ATM.
529 mm
(20.8 in.)
65 mm
(2.56 in.)
185 mm
(7.28 in.)
22
86 mm
161 mm (3.39 in.)
(6.34 in.)
117 mm
(4.61 in.)
B006-6585-A000
89 mm
(3.50 in.)
NCR 6632 ATM Site Preparation
Hot Air Outlets - Rear Access
The illustration below shows the position of the hot air outlets on the rear of the rear
access ATM.
48 mm
(1.89 in.)
478 mm
(18.8 in.)
525 mm
(20.70 in.)
120 mm
(4.72 in.)
125 mm
(4.92 in.)
125 mm
(4.92 in.)
129 mm
(5.08 in.)
129 mm
(5.08 in.)
B006-6585-A000
23
NCR 6632 ATM Site Preparation
REQUIREMENTS FOR THE FLOOR
The ATM is suitable for mounting on a concrete or other non-combustible surface only.
Floor Covering
An antistatic floor covering should be used and must be of a type that will not generate
dust or fluff. The surface on which the ATM is to be sited should be level and even. In
locations where the floor may be uneven, it is recommended that a steel plate is used under
the ATM.
Floor Loading
The ATM must be installed on a floor capable of supporting the maximum weight. Only
the maximum weight should be considered as additional options may be added after
installation.
Maximum weight without
removable media
Floor loading
24
UL
CEN Grade L
CEN Grade III or
CEN Grade IV
Spanish Certified
925 kg
(2040 lb.)
940 kg
(2073 lb.)
1160 kg
(2558 lb.)
1502 kg/m²
(308 lb./ft²)
1526 kg/m²
(313 lb./ft²)
1883 kg/m²
(386 lb./ft²)
B006-6585-A000
NCR 6632 ATM Site Preparation
BOLT HOLE LOCATIONS
The following illustrations show a plan of the base of the ATM (viewed from above). The
plan should be used for pre-drilling bolt holes ‘A’ and illustrates the design of the steel
plate, if used.
Front Access
UL Security Enclosure Bolt Hole Locations
The illustration below shows the dimensions for a front access ATM configured with a UL
security enclosure.
770 mm
(30.3 in.)
A
426 mm
(16.8 in.)
A
43 mm
(1.7 in.)
Ø 28 mm
(1.1 in.)
4 Places
23 mm 33 mm
(0.9 in.) (1.3 in.)
B
A
195 mm
(7.7 in.)
A
800 mm
(31.5 in.)
12 mm
(0.5 in.)
297 mm
302 mm
(11.7 in.)
(11.9 in.)
Front of ATM
285 mm
(11.2 in.)
270 mm
(10.6 in.)
Note: The boundary marked with a ‘B’ shows the cable access hole for all cables.
B006-6585-A000
25
NCR 6632 ATM Site Preparation
CEN Security Enclosure Bolt Hole Locations
The illustration below shows the dimensions for a front access ATM configured with a
CEN security enclosure.
770 mm
(30.3 in.)
A
A
774 mm
(30.5 in.)
65 mm
(2.6 in.)
426 mm
(16.8 in.)
B
100 mm
(3.9 in.)
C
A
A
169 mm
(6.7 in.)
33 mm
(1.3 in.)
276 mm
(10.9 in.)
Front of ATM
285 mm
(11.2 in.)
270 mm
(10.6 in.)
Ø 28 mm
(1.1 in.)
Ø 28 mm
(1.1 in.)
Ø 45 mm x 23 mm
(1.8 in.)
(0.9 in.)
Deep
Counterbore
Ø 60 mm x 28 mm
(2.4 in.)
(1.1 in.)
Deep
Counterbore
Detail of Hole A
Detail of Hole B
Note 1: The hole, marked with a ‘B’, enables a security alarm sensor to be fitted on CEN
Grade L or CEN Grade III.
Note 2: The boundary marked with a ‘C’ shows the cable access hole for all cables.
26
B006-6585-A000
NCR 6632 ATM Site Preparation
Rear Access
UL Security Enclosure Bolt Hole Locations
The illustration below shows the dimensions for a rear access ATM configured with a UL
security enclosure.
770 mm
(30.3 in.)
A
426 mm
(16.8 in.)
A
Ø 28 mm
(1.1 in.)
4 Places
B
A
140 mm
(5.5 in.)
43 mm
(1.7 in.)
33 mm
23 mm
(1.3 in.)
(0.9 in.)
A
800 mm
12 mm
(31.5 in.)
(0.5 in.)
392 mm
397 mm
(15.4 in.)
(15.6 in.)
Front of ATM
285 mm
(11.2 in.)
270 mm
(10.6 in.)
Note: The boundary marked with a ‘B’ shows the cable access hole for all cables.
B006-6585-A000
27
NCR 6632 ATM Site Preparation
CEN Security Enclosure Bolt Hole Locations
The illustration below shows the dimensions for a rear access ATM configured with a
CEN security enclosure.
770 mm
(30.3 in.)
A
A
100 mm
(3.9 in.)
65 mm
(2.6 in.)
B
800 mm
(31.5 in.)
C
426 mm
(16.8 in.)
33 mm
(1.3 in.)
A
A
140 mm
(5.5 in.)
397 mm
(15.6 in.)
Front of ATM
285 mm
(11.2 in.)
270 mm
(10.6 in.)
Ø 28 mm
(1.1 in.)
Ø 28 mm
(1.1 in.)
Ø 45 mm x 23 mm
(1.8 in.)
(0.9 in.)
Deep
Counterbore
Ø 60 mm x 28 mm
(2.4 in.)
(1.1 in.)
Deep
Counterbore
Detail of Hole A
Detail of Hole B
Note 1: The hole, marked with a ‘B’, enables a security alarm sensor to be fitted on CEN
Grade L or CEN Grade III.
Note 2: The boundary marked with a ‘C’ shows the cable access hole for all cables.
28
B006-6585-A000
NCR 6632 ATM Site Preparation
SECURITY BOLTS
To meet security standards the ATM must be bolted to the floor, through the ‘A’ holes,
using four bolts with anchor washers as specified below. The floor must be capable of
withstanding the loading imposed by the anchor points for the bolts. Bolts and anchor
washers are to be supplied by the owning organisation.
The minimum specification for bolts to secure the ATM to a concrete floor and meet
security standards, is high tensile M16 (5/8 in.) bolts with appropriate anchor washers of 6
mm (0.2 in.) minimum thickness. Bolts should be a minimum depth of 150 mm (5.9 in.)
and either resin anchor bolts or shield anchor type bolts.
Note 1: Bolting of CEN security enclosures should comply with the requirements of EN
1143-1 (CEN Safe Burglary Standard).
Note 2: For CEN L, CEN 1 and CEN III safes there is an additional fifth central
anchoring hole (hole ‘B’) of a larger counterbored diameter that can be used to fit a special
local alarm sensor.
B006-6585-A000
29
NCR 6632 ATM Site Preparation
VIDEO CAMERA
Ambient Lighting
If the ATM is fitted with a video camera, it is strongly recommended that there is a
minimum of 50 LUX lighting at floor level within the area illustrated below. This lighting
level conforms to:
Australian Standard for Automatic Teller Machines (1990)
Lighting for Automatic Teller Machines as prepared by Illuminating Engineering
Society of North America (1997).
1000 mm
(39.4 in.)
1500 mm
(59.1 in.)
30
B006-6585-A000
NCR 6632 ATM Site Preparation
Internal Space Constraint for Fitting a Third-Party Video
Camera
The ATM can be ordered with a video camera in either PAL or NTSC format. However, if
a camera is not configured and a third-party video camera is to be installed, there is a
space constraint to consider. The following illustration shows the space constraint
dimensions.
A list of cameras that will fit within this space constraint can be found in the ATMs
Feature Descriptions (B006-6451) book.
38 mm
(1.5 in.)
92 mm
(3.6 in.)
82.5º
26 mm
(1.0 in.)
B006-6585-A000
125 mm
(4.9 in.)
31
NCR 6632 ATM Site Preparation
32
B006-6585-A000
To help NCR maintain the quality of their publications, send comments on the accuracy, clarity,
usability, navigation, organization, and value of this book.
Address correspondence to:
Surface mail address:
NCR Financial Solutions Group Ltd
Information Solutions
Kingsway West
Dundee
Scotland
DD2 3XX
Email address:
userfeedback@exchange.scotland.ncr.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising