ct630 standard specifications

ct630 standard specifications
CT630 STANDARD
SPECIFICATIONS
CT630
CHASSIS
Heat-treated steel, yield strength: 120 000 psi, 760MPa
Frame rail dimensions: 260 x 92 x 9.5mm, section modulus 291cm3
Heavy Duty Intermediate cross member
Huck bolted to minimise maintenance
Aluminium deck plates behind cab
Tapered end of frame with fifth-wheel mounting angles
Double front tow hooks
Stainless steel bright finish bumper
Front Underrun Protection Device
FRONT AXLE
Meritor MFS 14-143A wide track RHD
Type: Forged steel I-beam
Capacity: 6,500kg
Steel Hubs
Option: Alloy Hubs
FRONT SUSPENSION
Type: 3 leaf parabolic springs, 1480mm long
Tuned shock absorbers
Capacity: 6,500kg
BRAKES
Dual Circuit Air System, S-Cam brakes
Size: front 419mm x 127mm with T24 chamber
Size: rear 419mm x 178mm with type 30/30 chambers
Park brake: both rear axles, spring-actuated
Haldex auto slack adjusters
Air dryer, Bendix AD-IS
Air compressor, Cat 15.7cfm capacity
Three manual drain valves with pull chains
Dust shield on all axles
Trailer brake hand control on steering column
Semi-trailer air connections at back of cab
Option: Hose tender slide bar, upper rear of cab
Bendix 4-channel ABS with full vehicle wheel control system
with automatic traction control
STEERING
Sheppard M100 power steering gear
Gear-driven power steering pump
Adjustable tilt telescopic steering column with leatherwrapped 2-spoke steering wheel, 457mm diameter
EXHAUST
Dual DPF catalytic muffler system, frame mounted with
shroud and dual vertical tail pipes
ELECTRICAL SYSTEM
LED headlights, with auto on windscreen wiper function and
daytime running lights
12-Volt, negative to earth
Diamond Logic multiplexing system
Cat Batteries: 4 x 12V, RHS chassis mounted
Alternator: 12V, 160 amp, brush-type, pad-mounted
Starter, 105P with Soft Start
Two trailer sockets, 7-pin trailer lighting and an EEC socket for
trailer ABS, at rear of cab
Exterior light test system for pre-trip inspection
Circuit breaker with manual reset
Switches for provision of operating PTO, and rear work lamps
Park brake warning horn if brake not applied and door opened
Back-up alarm, 102 dba
Option: Work light connection on chassis
Option: P.T.O. prep kit (switch and wiring loom)
ENGINE
Cat C15 ACERT ADR 80/03 emissions compliant
6-cylinder, in-line, turbocharged and aftercooled,
electronic direct injection with dual DPF
Displacement: 15.2-litres
Cruise control with steering wheel controls.
Rated at 550 hp @ 1800 rpm and 1850 lb.ft torque
@ 1200 rpm. 2100 governed rpm.
Jacobs engine brake, 3 stage switching
High-capacity under-hood air cleaner with restriction
indicator gauge
Fuel priming pump
Excellent engine access
100 kph road-speed limited
COOLING SYSTEM
Over-and-under system
Total package: 1545 in2
Horton DriveMaster air operated two-speed fan drive
Nylon fan
CLUTCH
Eaton Fuller Solo Advantage two-plate ceramic with
Self Adjust feature
Diameter: 394mm
Light pedal, integrated air-assist clutch release system
TRANSMISSION
Eaton Fuller RTLO-20918B 18-speed overdrive
Lube pump & oil-to-water transmission cooler
Option: Eaton UltraShift Plus Transmission
with Hill Start Assist
WHEELS AND TYRES
Passive regeneration
Wheels–Ten: bright finish alloy, 10-stud 285mm PCD,
8.25DC x 22.5 Tyres: 295/80R22.5 on front axle; 11R22.5 on rear axles
Chassis Weights (kg)
CT630
Turning Radius( (m)
Dimensions (mm)
Suspension
Front
Rear
Total
WB
BA
CA
CF
AF
OAL
BBC
Curb/Curb
Wall/Wall
CT630 Day Cab
HAS460
4500
3490
7990
4800
1290
2980
4530
1600
7690
3110
18.2
19.2
CT630 Extended Cab
HAS460
4610
3580
8190
5000
1290
2530
4130
1600
7890
3770
18.7
19.7
CT630 Day Cab
HAS460
4520
3500
8020
5200
1290
3380
4980
1600
8090
3110
19.3
20.3
CT630 Day Cab
HAS460
4540
3510
8050
5550
1290
3730
5330
1600
8440
3110
20.1
21.1
CT630 Extended Cab
HAS460
4600
3570
8170
4800
1290
2330
3930
1600
7690
3770
18.2
19.2
CT630 Day Cab
BBC
CF
CA
AF
BA
BA
WB
OAL
CT630 Extended Cab
BBC
CA
CF
AF
BA
BA
WB
GVM - 24.5 tonne
OAL
GCM - HAS460 - 72-tonnes
GCM - PAX460 - 90-tonnes
(B-double truck & trailer) - standard
(B-double or highway RT) - optional
REAR AXLE
CAB
Arvin Meritor RT-46-160
Day cab 2085mm wide, galvanised steel
Capacity: 20,900kg (46,000lb)
Base coat, clear coat paint
Ratio: 3.91:1
Optional Ratios: 4.10:1 or 4.30:1
ECE-R29 compliant
Inter-differential power divider lock
Differential cross-lock on rear/rear axle
Option: Additional cross-lock on forward rear axle
Option: Lube Pump with bypass
Electronic auto traction control standard
Steel Hubs
Option: Alloy Hubs
REAR SUSPENSION
Tilting SMC hood and removeable quarter fenders
Bright polished stainless-steel grille surround
Three-point cab mounting system with rear air suspension
Drivers Seat: Gramag, hi-back, air suspended, leather trim fitted
with adjustable arm rests and integrated seat belt
Passenger Seat: Gramag, hi-back, air suspended, leather trim
fitted with adjustable arm rests and integrated seat belt
Full instrument panel with on-board diagnostics display for
diagnosis of fault codes in gauge cluster
Stowage compartments in overhead console
HAS
Premium trim with additional sound insulation
Hendrickson HAS 460-55 (1850 lb.ft) suspension engineered
to meet Australian Specification with road friendly compliance
Moulded access handles with 3 point entry and exit
1397mm axle spacing
Power windows fitted for both driver and passenger
Suspension dump valve with control switch in instrument panel
STANDARD ACCESSORIES
Load sharing suspension
Capacity 20,900kg (46,000lb)
PRIMAAX EX
Hendrickson PAX 460 (1850 lb.ft) suspension engineered to
meet Australian Specification with road friendly compliance
Suspension dump valve with control switch in instrument panel
Capacity 20,900kg (46,000lb)
Inner frame suspension liner
DRIVESHAFT
Main Shaft – SPL250XL
Interaxle Shaft – SPL170XL
Quarter vent windows, Rear window
Internal sun visors, front and separate side primary visors
Air-Conditioner, Heater with fresh air filter system
Twin windscreen wipers/washers, 2-speed with intermittent action
Electrically adjustable heated mirrors with separate spotter
mirrors on both sides
Single air-horn, chassis mounted
Outside temperature and compass in dash display
Option: Aerodynamic packages available
EXTENDED SLEEPER
26” (660mm) Extended (Sleeper) cab with 3770mm BBC
Sleeper includes: Single 660mm x 1840mm x 127mm lower bunk
(mattress) dome light, under-bunk storage
FUEL SYSTEM
984-litres total capacity (Day Cab and Extended Cab)
Bright finished aluminium 660mm diameter cylindrical tank
with alloy steps
Dual Pick-up and return
Fuel cooler, radiator mounted
INSTRUMENTATION
Electronic speedometer and tachometer
Gauges: engine oil pressure, voltmeter, engine oil temperature,
air pressure, coolant temperature, fuel level, transmission
temperature, rear axle temperatures, fuel trip data
Warning system: low air pressure, low fuel, low oil pressure, high
engine coolant temp and low battery voltage (visual and audible)
www.cattrucks.com.au
®2014 Caterpillar All Rights Reserved Printed in Australia CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as corporate and
product identity used herein, are trademarks of Caterpillar and may not be used without permission.
All efforts have been made to ensure the information contained in this document was correct at time of printing or uploading. Images displayed are for illustration purposes only. Tare
weights are provisional figures and have been calculated to provide the best accuracy possible, and may be subject to variation.NC2 Global Australia Pty Ltd reserves the right to alter
any details of the specifications and equipment without notice. NC2 Global Australia Pty Ltd in so far as it is permitted by law to do so, shall not be liable in any way as a result of any
reliance placed by any person on anything contained in this brochure. You should therefore check with your authorised Cat Trucks dealer at the time of ordering your truck to ensure
that colour, specifications, equipment, design features and options are available for the vehicle you are ordering. Please note that some options may only be available in combination
with others. Authorised Cat Truck dealers will on request from NC2 Global Australia Pty Ltd provide up to date information on all accessories, design features, prices and availability. POS 2014_R1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising