Models 62022-4-Series 62040-4 Series 62026-4-Series

Models 62022-4-Series 62040-4 Series 62026-4-Series
Models 62022-4-Series 62040-4 Series
62026-4-Series 62042-4 Series
FEATURES
• Complete drive unit enclosed in light housing.
• Single control lever for vertical and horizontal
movement.
• Dual speed control for precise beam movement.
• On-off and spot/flood beam selection from a single
switch.(Spot only on 7" and 8"models).
• Exclusive Clutch-A-Matic feature protects drive unit
against overload. Can operate for extended periods
against limit stops without harm. Light head may be
moved manually without damage to the drive unit.
Model 62022-4002
• Internal brake system holds beam firmly on target.
• Includes control with on-off, spot/flood switch, dual
speed control, and single control for vertical and
horizontal movement.
Model
Number Volts Head Base
62022-4002
62026-4002
62040-4002
62040-4006
62042-4006
12
12
12
24
24
Brass
Brass
Brass
Brass
Brass
Bulb
Type
Candlepower
(Combined)
Zinc 5" Spot/Flood
Brass 5" Spot/Flood
Brass
7" Spot
Brass
7" Spot
Brass
8" Spot
150,000
150,000
230,000
230,000
500,000
CABLE LISTING
Part Number
43990-0013
43990-0014
43990-0015
43990-0016
67294-0000
Model 62026-4002
10'
15'
25'
35'
50'
Description
Cable Assembly
Cable Assembly
Cable Assembly
Cable Assembly
Bulk Cable
CONTROLS
Part Number
43670-0003
43670-0004
60070-0000
18753-0335
Description
Primary Control 12 V
Secondary Control Kit 12 V
Primary Control 24 V
Secondary Control Kit 24 V
Models 62040 & 62042-Series
Models 62022-4-Series, 62040-4 Series, 62026-4-Series, 62042-4 Series
5", 7" & 8" ELECTRIC REMOTE
CONTROL SEARCHLIGHTS
LIGHT MOUNTING
See base mounting dimensions for appropriate model
light. Mount all models with front of base toward direction
of most intended use (front of circular base is marked
with arrow). Drill screw holes (per dimensional drawing)
and a 1-1/8" (28mm) hole at center of base for wiring
cable. Drill additional holes for wiring cable through
firewalls, bulkheads, etc., for connection to control. With
gasket under light base, feed wire through hole and
fasten light in place.
NOTE: Cable connectors are provided for easy wiring
connections. See Wiring Diagram.
CONTROL MOUNTING
43670-0003 12 VOLT & 60070-0000 24 VOLT
Select a location near the helm which will allow
convenient operation of control. Unit may be mounted on
vertical, horizontal or inclined panel.
1. Cut 2-5/8" (67mm) diameter hole in flat surface
where control is to be mounted.
2. Route power leads (supplied by customer) from
power source to control. NOTE: Wiring must be 16
gauge with maximum run of 15 ft.
3. Crimp terminals supplied onto power leads. NOTE:
Larger terminal is crimped to positive lead – smaller
terminal to negative lead.
4. Insert wiring cable and power leads thru back of hole
and plug into control.
5. Use bedding compound or sealant to waterproof
control mounting.
6. Secure control with self-tapping screws provided.
CIRCUIT PROTECTION
Two (2) automotive type fuses are included in the
control. One (10 amp) protects the bulb circuit, the other
(3 amp) protects the motor circuit.
Fuse
Fuse
OPTIONAL SECONDARY CONTROL
MOUNTING
If an additional control station is desired, use control kit
number 43670-0004 12 Volt, 18753-0335 24 Volt. Mount
secondary control in same manner as main control.
Mount station selector panel near the main control
(flybridge or lower).
1. Cut a 2" x 1-3/8" (51mm x 35mm) opening for station
selector panel within a 1 foot radius of the control.
2. Route secondary control cable from station selector
panel to secondary control location (cable acquired
separately – see cable listing).
3. Insert station selector panel thru mounting hole and
attach connectors to mating connectors from
controls and searchlight. The connectors marked
“flybridge” to go to flybridge control and the
connector marked “lower” to lower control. The
connector to the nearest control can be plugged
directly into the control. See diagram.
4. Use bedding compound or sealant to waterproof
station selector panel mounting.
5. Secure panel with self-tapping screws provided.
TROUBLESHOOTING
All lights are thoroughly inspected before shipping and are warranted to operate within specifications. If light does
not operate correctly, CHECK FUSES, AND WIRE HARNESS CONNECTIONS BEFORE PROCEEDING WITH THIS
TROUBLESHOOTING.
PROBLEM
SOLUTION
1. Dual filament bulb works in reverse. . . . . . . . . . . . . . . . . . . Reverse orange and gray wires at the bulb terminals.
2. Control lever works in reverse in all directions. . . . . . . . . . . Power leads to control are reversed.
3. Light moves in only three of the possible four directions. . . A. Check connectors.
B. Replace control.
C. If problem persists, return light & control
for service.
4. Dim light (low voltage). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A. Check voltage at power source.
B. Refer to cable listing for proper wire gage
and length.
5. Bulb operates – no light movement . . . . . . . . . . . . . . . . . . . Check fuses on front of control.
or
Light moves – bulb does not operate.
EXPLODED VIEW
2
6
7
5
2
6
7
5
3
8
10
4
11
10
4
3
1
9
Key
No.
1
1
1
9
9
62022-4002
Part No. Qty.
Part Description
62026-4002
Part No. Qty.
62040-Series
Part No. Qty.
62042-Series
Part No. Qty.
Base (includes set screw)
Chrome - Zinc
Chrome - Brass
66130-0000
–––
1
–
–––
43990-0030
–
1
–––
43990-0031
–
1
–––
43990-0031
–
1
2
Housing (rubber boot installed)
(includes end bell (No.8) on 7" & 8")
Chrome - Brass Housing
43990-0032
1
43990-0032
1
43998-0000
1
43966-0000
1
3
Screws for mounting housing
(package of 4 screws)
66138-0000
1
66138-0000
1
66138-0000
1
66138-0000
1
4
Rubber Boot (includes straps and fasteners)
43990-0045
1
43990-0045
1
43990-0046
1
43990-0046
1
5
Motor Clutch Assembly (assembled and wired)
43990-0075
1
43990-0075
1
43990-0076
1
43990-0076
1
6
Motor & Pinion Kit (vertical
horizontal)*
43990-0078
43990-0079
1
1
43990-0078
43990-0079
1
1
43990-0078
43990-0079
1
1
43990-0078
43990-0079
1
1
7
Bulb Retaining Ring (chrome) (w/fasteners)
66149-0000
1
66149-0000
1
43990-0039
1
43990-0040
1
8
End Bell (w/fasteners)
–––
–
–––
–
See Key #2
–
See Key #2
–
9
Gasket (base mount)
66155-0000
1
66156-0000
1
66157-0000
1
66157-0000
1
10
Bulb 12 Vdc
24 Vdc
67296-0000
–––
1
–
67296-0000
–––
1
–
67262-0000
18753-0447
1
1
67524-0000
98040-0520
1
1
11
Primary Power Relay - 12 Volt Model only**
–––
–
–––
–
–––
–
43789-0000
1
43990-0069
43990-0000
–
1
43990-0069
43990-0000
1
1
43990-0069
43990-0000
1
1
43990-0069
43990-0000
1
1
Gear & Clutch Kit (not shown)
Replacement 8-Way Switch
for Control (not shown)
*Vertical & horizontal refer to movement, not orientation or the motor inside the housing.
**For older 12 Volt, 8" models only.
BULB REPLACEMENT
Loosen screw and remove bulb retaining ring.
Disconnect wires from faulty bulb. Connect
wires to new bulb as shown. Install bulb and
fasten with bulb retaining ring.
DUAL FILAMENT SPOT/FLOOD
Gray
(Flood)
Black
(Neg.)
Orange
(Spot)
SINGLE FILAMENT
Black
(Neg.)
Gray &
Orange
(Spot)
WIRING DIAGRAM SINGLE CONTROL
5" & 7" MODELS
8" MODEL
POWER INPUT
LEADS SUPPLIED
BY CUSTOMER (16 GA.)
POWER INPUT
LEADS SUPPLIED
BY CUSTOMER (16 GA.)
20 AMP FUSE
(SUPPLIED) MUST
BE INSTALLED BY
CUSTOMER IN
POSITIVE LEAD
8' CONTROL CABLE INCLUDED
WITH 5" LIGHTS ONLY
FOR ADDITIONAL CABLES
SEE CABLE LISTING.
CONTROLLED CABLE MUST BE
ACQUIRED SEPARATELY
(SEE CABLE LISTING)
+
–
CONTROL
CONTROL
POWER INPUT
LEADS SUPPLIED
BY CUSTOMER (16 GA.)
ATTACH WITH BUTT
CONNECTORS SUPPLIED
7"
(178mm)
DIMENSIONAL DRAWINGS
7"
(178mm)
4-5/8"
(118mm)
4-5/8"
(118mm)
9-1/2"
(241mm)
7-1/8"
(181mm)
5" BRASS
BASE
5" ZINC
BASE
BASE MOUNTING
DIMENSIONS
3-5/8"
(92mm)
3/16" (4,8mm) DIA. HOLES (3 PLCS)
FOR NO.8 FLATHEAD SCREWS
3/16" (4,8mm) DIA.
MOUNTING HOLES
(3 PLCS) FOR NO.8
FLATHEAD SCREWS
120°
TYP.
3"
3-5/8"
(76mm) (92mm)
3-1/8"
(79mm)
3-11/16"
(94mm)
5"
(127mm)
1-1/2"
(38mm)
11-3/16"
(284mm)
11-3/4"
(299mm)
BASE MOUNTING
DIMENSIONS
7"
(178mm)
13"
(330mm)
8-5/16"
(211mm)
7/32" (5,5mm) DIA.
HOLES (3 PLCS) FOR
NO.10 FLATHEAD SCREWS
14-5/16"
(363mm)
3"
4-1/8"
(76mm) (105mm)
7" LIGHT
5-5/8"
(143mm)
8" LIGHT
1-1/8"
(38mm)
THE PRODUCTS DESCRIBED HEREIN ARE
SUBJECT TO THE JABSCO ONE YEAR LIMITED
WARRANTY, WHICH IS AVAILABLE FOR YOUR
INSPECTION UPON REQUEST.
U.S.A.
Jabsco
Cape Ann Industrial Park
Gloucester, MA 01930
Tel: 978.281.0440
Fax: 978.283.2619
© Copyright 2004, ITT Industries
UNITED KINGDOM
Jabsco
Bingley Road, Hoddesdon
Hertfordshire EN11 OBU
Tel: +44 (0) 1992 450145
Fax: +44 (0) 1992 467132
Printed in U.S.A.
CANADA
Fluid Products Canada
55 Royal Road
Guelph, Ontario N1H 1T1
Tel: 519 821.1900
Fax: 519 821.2569
JAPAN
NHK Jabsco Company Ltd.
3-21-10, Shin-Yokohama
Kohoku-Ku, Yokohama, 222
Tel: 045.475.8906
Fax: 045.475.8908
All Rights Reserved
GERMANY
Jabsco GmbH
Oststrasse 28
22840 Norderstedt
Tel: +49-40-53 53 73 -0
Fax: +49-40-53 53 73 -11
Form: 43000-0494
Rev. 04/2004
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising