HYDRAULIC EARTH DRILLS MAINTENANCE

HYDRAULIC EARTH DRILLS MAINTENANCE
HYDRAULIC
EARTH DRILLS
OPERATORS MANUAL
WITH
MAINTENANCE AND
PARTS INFORMATION
1110
1-800-227-7515
P.O. BOX 840
LIVINGSTON, TEXAS 77351
PHONE 936/327-3121
FAX 936/327-4025
Web: www.littlebeaver.com
E-Mail: sales@littlebeaver.com
MFG. BY: LITTLE BEAVER, INC. - LIVINGSTON, TEXAS USA
CUSTOMER SERVICE
Ph: 800/227-7515 or 936/327-3121 or Fax 936/327-4025
ORDERS...
Place your orders by telephone, fax, or mail. When calling, please have your parts
manual handy for reference. Our hours are 8:00 am - 4:30 pm central time, Monday
thru Friday. When ordering by mail or fax, include a description and LITTLE BEAVER
part number for the items you are ordering, your return address, and payment or your
authorization for COD shipment.
All orders are shipped UPS where possible. Freight charges will be added to your
invoice. Some items are oversize, resulting in a higher shipping cost. Power units and
larger augers are shipped via motor freight due to their weight.
PAYMENT TERMS...
COD, Cash in Advance, Visa, Mastercard or NET 30 with approved credit. COD limit
for new accounts is $500.00. Personal or company checks on new accounts will be
held until they clear the bank. To eliminate this delay, you may pay by wire transfer
or send a certified or cashiers check. For a NET 30 open account, please call or write
for a credit application.
SERVICE AND REPAIR...
Your LITTLE BEAVER Earth Drill has been designed for user repair with ordinary hand
tools. No special tools are required. Consult the appropriate section of the parts
manual for instructions.
Service or technical consulation is available, free of charge, from the factory in
Livingston, Texas. We will be pleased to help you with any problems or questions. Just
write, fax, or call. Our hours are 8:00am - 4:30pm central time, Monday thru Friday.
Factory repair is available. If you return a part to the factory, please include the
following information: Your name and return address, a description of the problem
and payment or authorization to return the repaired item COD for the repair and
shipping charges.
RETURNS...
Please call the factory for a return authorization. This will help to ensure that your
parts are handled properly. Include your name and address, customer account #,
invoice # under which the returned parts were ordered, and a brief description of the
problem with the parts or the reason for returning them. Parts to be considered for
warranty must be returned to the factory for inspection within 10 days after receipt
of replacement parts. Be sure to prepay the shipping charges, we will not accept
collect or COD packages.
Our mailing address...
LITTLE BEAVER, Inc.
2009 South Houston
P. O. Box 840
Livingston, Texas 77351
0196
SAFETY ALERT SYMBOL
The symbol shown above is used to call your attention to instructions concerning your personal safety.
WATCH THIS SYMBOL — It points out important safety precautions. It means — ATTENTION! BECOME
ALERT! YOUR PERSONAL SAFETY IS INVOLVED!
Read the message that follows and be alert to the possibility of Personal Injury or Death!
WARNING:
The Engine Exhaust from this product contains chemicals known
to the State of California to cause cancer, birth defects or other reproductive harm.
l
lllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllll
1 YEAR LIMITED WARRANTY
For 1 year from purchase, LITTLE BEAVER, INC. will replace for the original purchaser,
free of charge, any part or parts, found upon examination by any factory authorized service
center, or by the factory at Livingston, Texas, to be defective in material or workmanship or
both. If your equipment can not be repaired, it will be replaced. All transportation charges
on parts submitted for replacement under this warranty must be borne by purchaser.
There is no other express warranty.
Implied warranties, including those of merchantability and fitness for a particular purpose,
are limited to 1 year from purchase and to the extent permitted by law. Any and all implied
warranties are excluded. This is the exclusive remedy and liability for consequential damages
under any and all warranties are excluded to the extent exclusion is permitted by law.
*Notice: Engines are warrantied by the manufacturer of the engine. See separate engine
warranty enclosed.
lllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllll
MACHINE SERIAL NUMBER
There are two serial numbers for your hydraulic earth drill, one for the handle and one for the power
source. The handle serial number is located on the bottom side of the handle. The power source serial
number is located on the rear side of the hydraulic reservoir. For your convenience, when requiring
service or parts information, refer to these numbers and your model numbers. Record the serial
numbers, model numbers, engine make and date of purchase in the space provided below:
Handle Serial Number:
Power Source Serial Number:
Handle Model Number:
Power Source Model Number:
Engine Make:
Date of Purchase:
Page O-1
1004
TABLE OF CONTENTS
OPERATORS MANUAL
Page #
O-1
O-2
O-3
O-4
O-5
O-6 & 7
O-6
O-7
O-8
O-9
Safety Alert, Warranty and Machine Information
Table of Contents
Safety Instructions and Specifications
Maintenance and Lubrication Instructions
Wheel and Torque Tube Assembly
Operating Instructions
Handle and Auger Operation Information
Extension and Accessories
Decal Location
Troubleshooting
PARTS MANUAL
Page #
P-1 & 2
P-3
P-4
P-5& 6
P-7 & 8
P-9 & 10
P-11 & 12
P-13
Tank & Carrier Assembly
Pump, Filter and Sight Guage Assemblies
Torque Tube and Wires
One-Man Handle
Two-Man Handle
Anchor Handle
Auger Information
Extensions & Adaptors
Hydraulic Notes
Prices for Hydraulic Parts and Augers
Inside Back Cover...Torque Information and Conversion Chart
Page 0-2
0196
SAFETY INSTRUCTIONS
DANGER: Failure to observe safety instructions and reasonable safety practices can
cause Property Damage, Serious Bodily Injury and/or Death. BE CAREFUL!! WATCH OUT
FOR BYSTANDERS!!
DANGER: NEVER run engine inside building or enclosed area. Exhaust gases contain carbon
monoxide, an odorless and deadly poison.
DANGER: NEVER drill holes where there is a possibilityof underground power cables or other
hazards. The exact location of underground services must be determined prior to drilling.
Inadvertent severing of telephone, fiber optic or CATV transmission cable, or damage to sewer
pipe is costly; RUPTURING OF GAS OR WATER LINES CAN CAUSE SERIOUS BODILY INJURY AND/
OR DEATH. COMING INTO CONTACT WITH BURIED POWER LINES CAN CAUSE SERIOUS BODILY
INJURY, SEVERE BURNS, AND/OR ELECTROCUTION. Call local utility companies or your local "OneCall" number at least 48 hours before digging and have underground utilities marked.
WARNING: Never use hands to search for leaks. Instead, use a piece of cardboard or wood.
Escaping hydraulic fluid under pressure can have sufficient force to penetrate the skin, causing
serious injury. Before disconnecting lines, be sure to relieve pressure. Before applying pressure,
be sure connections are tight and fittings and hoses are not damaged.
WARNING: Augers are not to be used as anchoring devices.
CAUTION:
1. READ and understand this operator’s manual and the operator’s manual for the engine.
2. NEVER Operate drill without correctly installing torque tube.
3. NEVER Remove auger from hole while auger is turning.
4. NEVER Operate auger at less than full throttle.
5. NEVER Operate drill with damaged auger or other damaged or missing parts.
6. KEEP Hands, Feet and Clothing away from moving parts while engine is running.
7. KEEP All safety shields and devices in place.
8. MAKE Certain everyone is clear before operating the machine.
9. KEEP Leg pad against leg while drilling to maintain safe control.
10. WEAR SAFETY GLASSES.
11. KEEP Bystanders away from work area.
12. SHUT OFF Engine to adjust, service or clean the machine.
NOTICE
It is the responsibility of the contractor, owner and user to maintain and operate the Earth Drill in
compliance with operating instructions provided. Observe all listed safety instructions and other
reasonable safety practices. LITTLE BEAVER, INC. accepts no responsibility for damages to this machine,
and other property damage and/or bodily injury due to careless or improper operations.
LITTLE BEAVER, INC. does not recommend or condone any modifications which would eliminate the torque
tube.
LITTLE BEAVER, INC. does not recommend use of replacement hydraulic motors which would result in
auger shaft torque greater than 400 ft.-lbs. If greater torque is required, please consult factory.
LITTLE BEAVER, INC. reserves the right to make changes in design and changes for improvements upon
its product without imposing any obligation upon itself to install the same upon its products theretofore
manufactured.
Your operators manual offers recommendations for prolonged and satisfactory service.
SPECIFICATIONS
11 HP Honda, 11 HP Briggs & Stratton OR 11 HP Wisconsin
6 GPM @ 2000 PSI
100 Micron Suction Screen
10 Micron Replaceable Return Line Filter
5 Gallon Hydraulic Reservoir
Page O-3
0196
MAINTENANCE AND LUBRICATION INSTRUCTIONS
NOTE: All engines and hydraulic reservoirs are shipped WITHOUT oil.
ENGINE: The engine is shipped without oil or gasoline. Refer to the manufacturers instructions for
proper procedures and recommended fluid.
HYDRAULIC FLUID AND FILTER: The hydraulic reservoir should be filled to the top of the sight gauge
with hydraulic oil before attempting to start the engine. Most premium grade, mineral based oil with antiwear (AW) and anti-foaming additives are suitable. The recommended fluid for normal temperature
operation is ISO VG 46 grade fluid. In colder climates use ISO VG 32 grade and in warmer climates use
ISO VG 68 grade fluid. The hydraulic oil and return line filter (Part # 30280) must be kept clean at all
times, and should be changed after the first 15 hours of operation. The filter and oil should be changed
every three months or after 100 hours of operation; whichever comes first.
NOTE: The hydraulic fluid and engine crankcase oil levels should be checked prior to each
days use.
IMPORTANT: All nuts, fasteners, and fittings must be kept tightened. If the engine or tank
mounting bolts are allowed to loosen, premature coupling and/or pump wear may result.
CAUTION: Escaping hydraulic fluid under pressure can have sufficient force to penetrate the
skin, causing serious injury. Before disconnecting hydraulic lines, be sure to relieve
pressure. Before applying pressure, be sure connections are tight and fittings, pipes and
hoses are not damaged. Use a piece of cardboard or wood, rather than hands, to search for
leaks. If injured by escaping fluid, see a doctor at once. Serious infection or reaction can
develop if proper medical treatment is not administered immediately.
KEEP all hydraulic lines away from moving parts.
HYDRAULIC OIL LEAKAGE
If any hydraulic oil leakage is encountered, shut down the power source and relieve the hydraulic
pressure by moving the throttle valve in both directions. Check and tighten the screw-on fittings on the
end of each hose. If the leakage persists, it may be necessary to replace the associated hose assembly.
If one of the Quick Disconnect fittings is the source of leakage, the quick disconnect coupling should
be replaced. If the throttle valve is leaking around the spool (shaft), you may replace the seal kit (Part
# 30275-2).
NOTE: To obtain maximum performance from power source, minimum hose size
recommended is 3/8".
HYDRAULIC HOSE ASSEMBLY REPLACEMENT
WARNING: For power source serial numbers from H-0001 through H-3252, do not exceed
the following maximum hose assembly lengths. Longer hose assemblies may allow the torque tube
to uncouple, causing serious personal injury.
If replacement hose assemblies are required, the maximum overall length of the pressure/return
hose assembly on the handle is 36". The maximum overall length of the pressure hose assembly on
the power source is 74 1/4" and the maximum overall length of the return hose assembly on the
power source is 68".
EXCESSIVE HEATING
Excessive heating is caused by placing too much down pressure on the auger which causes the oil
pressure to reach relief pressure. Oil flowing over the relief valve generates the heat.
DECAL LOCATION
The decals which are provided with your machine are shown at the rear of this manual. The decals shown
should be in the locations as described. If any of the decals are missing or illegible, order replacement
decal kit # 30181-D# and install before operating the machine.
Page 0-4
0196
WHEEL ASSEMBLY
Attach a wheel to each end of the rear axle using a 3/4" flat washer and securing with a 1/8" x 1"
cotter key. Attach the front wheel to the swivel bracket using one 3/4" x 5-1/2" cap screw, two spacers,
and one 3/4" lock nut.
OPERATION
TORQUE TUBE ASSEMBLY
WARNING:
drilling.
Properly install torque tube to prevent serious injury from kick-back torque while
Figure 2
Figure 1
The torque tube consists of one end with a 1-1/2" square female fitting and a 1-1/4" square male
fitting on the other end. Attach the larger female end of the torque tube to the power source bracket
as shown in figure 1. Attach the other male end to the handle as shown in figure 2. Be sure to align the
snap button with the mating hole provided and check to be sure the snap buttons are securely snapped
into place.
BEFORE STARTING THE ENGINE,_Be sure that:
DANGER: NEVER run engine inside building or enclosed area. Exhaust gases contain carbon
monoxide, an odorless and deadly poison.
1.) Engine is properly prepared to Manufacturer’s specifications. Note: Engines with “Oil
Guard” protection must be filled with oil to full mark on dipstick or to point of
overflowing to allow the engine to start.
2.) Hydraulic Reservoir is filled to top of sight gauge.
3.) The torque tube is properly attached.
4.) There is no auger connected to the handle.
5.) The Quick Disconnect fittings are correctly coupled.
6.) The Torque Tube has engaged the Kill Switch at the Power Source.
TO START THE ENGINE: Set the choke lever to the “ON” position and pull the starter rope. The engine
should start after 2 or 3 pulls. Set the choke lever to the “OFF” position and allow the engine to warmup for 2 or 3 minutes.
0196
Page O-5
AFTER THE ENGINE HAS WARMED UP, Insert the auger into the drive adaptor on the bottom of the
handle. Make sure the snap button and hole provided in the adaptor are aligned and the button snaps
securely into place. Hold the handle so your left index finger and thumb can operate the throttle (pull
with the index finger for forward rotation, push with the thumb for reverse). NOTE: ONLY use reverse
to free the auger if it becomes lodged in the ground. Grasp the right handle bar with your right hand.
Stand so the auger is straight up-and-down and is properly positioned to dig your hole (see figures 3
& 4). Note the safety instructions in this manual and on the machine’s decals.
FIGURE 3
FIGURE 4
IMPORTANT: Keep the back as vertical as possible by bending the legs, as required, during the
operating and
lifting procedure.
ONE-MAN HANDLE
Always keep the leg pad against leg to maintain safe and stable control during operation.
TWO-MAN HANDLE
The operator controlling the throttle lever must alert the other operator prior to engaging the earth drill
to ensure readiness. Both operators must distribute even pressure on the auger, as required, to maintain
uniform drilling.
`
DANGER: NEVER drill holes where there is a possibilityof underground power cables or other
hazards. The exact location of underground services must be determined prior to drilling.
Inadvertent severing of telephone, fiber optic or CATV transmission cable, or damage to sewer
pipe is costly; RUPTURING OF GAS OR WATER LINES CAN CAUSE SERIOUS BODILY INJURY AND/
OR DEATH. COMING INTO CONTACT WITH BURIED POWER LINES CAN CAUSE SERIOUS BODILY
INJURY, SEVERE BURNS, AND/OR ELECTROCUTION. Call local utility companies or your local
"One-Call" number at least 48 hours before digging and have underground utilities marked.
MAKE certain everyone is clear before operating the machine.
KEEP hands, feet and clothing away from moving parts while engine is running.
START THE AUGER TURNING By pulling the throttle lever in completely. Always allow the auger to turn
at full speed and let it cut its way into the soil.
IMPORTANT: When digging in soft soil, hold up slightly on auger. In hard pan, apply pressure, but not
enough to stall the auger or slow it down significantly. The auger works best when it turns at full speed.
IF THE AUGER STALLS repeatedly or slows down significantly; stop the auger by releasing throttle lever,
slightly lift up on auger, start auger by pulling throttle lever, and allow the auger to turn at full speed
while slowly lowering it to bottom of hole.
NEVER Remove auger from hole while auger is turning.
When the desired depth is reached, stop the auger by releasing the throttle lever. Then pull the auger
completely out of the hole.
IMPORTANT: Keep the back as vertical as possible by bending the legs, as required, during the operation
and lifting procedure.
Page O-6
0196
AUGER EXTENSIONS
If greater hole depths are required, extensions
may be used with the auger. After the auger
has reached its maximum depth, stop the
auger and disconnect the drive adaptor from
the auger which remains in the hole. Connect
the extension to the auger as shown in figure
5. Connect the drive adaptor to the extension
and continue to dig the hole.
FIGURE 5
When the desired depth is reached, stop the auger and disconnect the drive adaptor from the
extension then remove the extension(s) and auger from the hole.
When working with cutting blade, point and auger flighting; be careful not to be cut by
sharp edges.
CUTTING BLADE
A
B
Check the cutting blade (Item A, Figure 6) on the auger frequently. If it becomes dull, it may be reversed to use the other
cutting edge. If the outside of the blade wears even with the
auger flighting, replace the blade or rebuild it with a hard
surfacing rod. This is very important to reduce auger flighting
wear and damage. The point (Item B, Figure 6) should be replaced when it loses its cutting shape.
FIGURE 6
ATTACHMENTS:
Several attachments are available for your LITTLE BEAVER Earth Drill; including both west and dry
type horizontal boring kits and a drill chuck adaptor which allows you to use a wood bit. Refer to
the specific operating instructions supplied with the attachment. If these become lost or misplaced,
replacements may be obtained from the factory.
0196
Page O-7
-A
DECAL LOCATION
-C
-E
-B
F-
-D
A
-G
B
H-
-I
C
D
E
F
G
I
H
For Decal Kit, Order Part # 30181-D#
Page O-8
1110
TROUBLESHOOTING
TROUBLE
CAUSE
Engine will not start
1)
2)
3)
4)
5)
Starter rope pulls hard,
with more resistance
than usual
1) Quick disconnect couplings are not fully connected. Push
together and rotate collar 1/4 turn.
Cannot connect or
disconnect auger
1) Foreign matter clogging auger adaptor
2) Spring and button in top of auger is bent or broken
Auger turns too slowly
and will not dig
1) Too much downward pressure or binding on side of hole. Hold
back if necessary to allow auger to turn at full speed.
2) Bent linkage between control level and valve. With engine off,
ensure that neither lever touches handle bar when moved to full
forward or reverse position.
Torque tube is not connected at power source
Engine stop switch is in "off" or "O" position
Low fuel level in gas tank
Low oil level in "Oil Guard" or "Oil Alert" equipped engines
Spark plug fouled
Auger turns but will not dig 1) Foreign matter collected around point
2) Point or blade is dull
3) Wrong blade type for soil condition. Contact your dealer or factory
for Little Beaver carbide blade
Auger with extension will
not dig
1) Auger or extension bent or running out of line
2) Number of extensions exceeds capacity of machine
Hydraulic oil and/or hoses
overheats
1) It is normal for the hoses and reservoir to be warm to the touch.
If it is very hot, consult your dealer or factory.
Auger turns when engine idles 1) Valve or linkage is binding. Do not use. Consult your dealer or factory.
Problems not listed in table
1207
1) Consult your dealer or factory.
Page O-9
TANK AND CARRIER ASSEMBLY
- 15
- 16
- 17
20 -
31
\
30
\
-2
------32
-6
------33
29
\
- 10
-9
-10
8-
- 28
- 18
25 \
26
27 -
\
36
-3
- 34
-4
- 11
/
12
- 24
/
13
- 37
- 16
- 14
5-
- 21
-7
19 -5
- 23
- 22
-7
Page P-1
0196
ITEM
PART #
DESCRIPTION
QTY
WARNING: For power source serial numbers from H-0001 through H-3252, do not exceed the
following maximum hose assembly lengths. Longer hose assemblies may allow the torque
tube to uncouple, causing serious personal injury.
2
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
30100
Pressure Hose - 74 1/4" max. overall length
30111
Return Hose - 68" max. overall length
30250-H*
Quick Disconnect Coupling, Female
30251-H*
Quick Disconnect Coupling, Male
3002-A
Cap Screw, Handle, Caster & Engine Mounting
30252
Handle, Front
3012-2
Screw - 3/8" x 1" GR 5
30198
Spacer, Handle - 5/16" x 5/8"
3012-3
Lock Washer - 3/8"
9027-KEP
Nut w/ Lock Washer - 3/8"
30253-A
Swivel Wheel Mount, Albion
30155-A
Axle, Swivel - 3/4" x 6" Hex Screw
30351
Spacer, Swivel Wheel - 3/4" ID x 1 1/8"
9096
Nut, Axle - 3/4"
3012-1T
Screw, Tank Top - 5/16"-18 x 3/4" GR 2
3002-C
Lock Washer - 5/16"
30254
Tank Top
30255
Tank
30256-H
Carrier
3002-KEP
Nut - 5/16"-18
30257
Handle Grip
30163
Cotter - Wheel 1/8" x 1"
30164
Washer, Wheel - 3/4" Flat
30348
Wheel, 12" - 3/4" Bore
3007-9
Kill Switch
9084-1
Spacer
9058
Spring & Button
30280***
Filter
30281
Filter Base
30282
Bushing
30283
Fitting
30312
Street Ell - 3/4"
30317
Diffuser, Oil Return Pipe
30313-11
Shim, 11 Ga - .120"
30313-14
Shim, 14 Ga - .083"
30313-16
Shim, 16 Ga - .065"
30313-18
Shim, 18 Ga. - .049"
30313-1
Shim Kit - 2 Shims of each size ( 8 total)
30159
Magnet Plug
30318
Nut, Engine Mounting - 5/16"-18 Lock Nut
*Power Source with SN#1675 and lower order complete set shown above.
**Quantity and Size may vary.
***Replacement Filter cross reference numbers are as follows:
Zinga #AE10, Ripley #DP75210, Amback #S-28 or Fram #P1653A
Page P-2
1
1
1
1
6
1
4
2
6
6
1
1
2
1
8
14
1
1
1
2
2
2
2
3
1
1
1
1
1
1
1
1
1
**
**
**
**
1
1
4
PUMP, FILTER AND SIGHT GAUGE ASSEMBLIES
/
8
28
31
\
/
9
10 -
-16
-11
13
/
6
|
/
27
12 -
/
18
Inside Tank
4
/
19
Tank Wall
765-
ITEM
2
3
4
5
6
7
8
9
10
11
12
13
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
PART #
30260
30262
30172
3012-2
3012-3
30154
30315
30316
30270-R
30291
30286
30263-D2
30310
30266
4019
30292-2
30267-58
30269
30268
30268-W
30171
4081
30295
30174
30154
30263-D2A
30314-D
30293
30294
30298
2
\
17
/
30
/
29
23
/
/
26
20
/
3
22
/
/
25
/
21 /
23
DESCRIPTION
Cap & Strainer Assembly
Sight Guage Assembly
Coupling Guard Assembly
Screw - Guard 3/8" x 1"
Lock Washer - Guard 3/8"
Nut - Guard 3/8"
Bushing #5406-8-6
Fitting #5603-6-6-6
Relief Valve
Hose - Pump to Tank - 11"
Fitting #6805-10-NWO
Dowty Pump with key, SAE-A 2-Bolt Flange
Nipple 3/4" x 2 1/2"
Suction Filter
Key - Pump
Gasket - Dowty Pump - SAE-A Flange (goes inside the tank)
Coupling - Pump End, Dowty - 5/8" Bore
Spider
Coupling - Engine End 1" Bore (Honda & B&S)
Coupling - Engine End 1 1/8" Bore (Wisconsin)
Set Screw
Key - Engine End
Bolt - 3/8" x 1 1/2" GR 5
Washer - 3/8" with Neophreme Seal
Lock Nut - 3/8" Nylon Insert
Dowty Pump Assembly (2 bolt mounting)
Seal Kit, Dowty Pump
Ring, Dowty Pump Tank
O-Ring #110 (goes outside tank)
Fitting, #6905-12-12-NWO
24 QTY
1
1
1
2
2
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
2
2
2
1
1
1
2
1
Page P-3
042004
TORQUE TUBE ASSEMBLY
3
/
2
/
4
/
-5
-6
1
/
-7
-8
ITEM
PART #
DESCRIPTION
QTY
1
9058-1
Button Shield
1
2
9092-M
One piece Torque Tube
1
3
9058
Spring & Button
1
4
9084-1
Spacer
1
5
30200
Kill Switch Wire (BIC)
1
6
30200-HW
Kill Switch Wire (Honda & Wisconsin)
1
7
3007-5
Plastic Tie
5
8
30201
Wire Loom
1
Page P-4
ONE-MAN HANDLE
-7
9
/
812 -
- 20
\
8
14 -
5-
26 -
- 17
13 -
- 28
- 18
- 27
10 - 15
- 16
22 \
19
21 -
- 25
6-
2-
I
29
23--
30-11--
3-
31-24--
4-
Page P-5
1101
ONE-MAN HANDLE
ITEM
PART #
DESCRIPTION
QTY
WARNING: For power source serial numbers from H-0001 through H-3252, do not exceed the
following maximum hose assembly lengths. Longer hose assemblies may allow
the torque tube to uncouple, causing serious personal injury.
2
3
4
5
30102-A
*30250-H
*30251-H
30115
30120-A
6
30296
30287
5076
30188
30275
30275-2
9026-KEP
10304
30178-A
30179
30180-A
30181-A
9034
3010-9
30183
3002-KEP
30191
30191-S2
6532
35312
30272
30010
9058-1
30158
30198
30182
9021
10520
9025
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Hose-Valve to Power/Valve to Return, 36" max. overall length
Disconnect Coupling-Female
Disconnect Coupling-Male
Hose-Valve to Motor 15 1/2"
Hose-Valve to Motor 19 1/2"
NOTE: SN H-163 & lower order Part #30103
Fitting-Pipe Swivel-Female (O-Ring)
Fitting-NPT
Cap Screw 1/4" x 2" USS-Valve Mounting
Pushnut, Locking Washer
Throttle Valve
Seal Kit (Valve)
Nut 1/4" KEP (Nut w/Lock Washer)
Washer, 1/4" Standard
Throttle Linkage
Cotter Key 3/32" x 5/8"
Throttle Lever
One-Man Handle ONLY
Leg Pad
Screw 5/16" x 2"-Hose Clamp
Clamp-Hose
Nut 5/16" KEP (Nut w/Lock Washer)
Hydraulic Motor w/2 bolt flange-220 RPM (103-1035 )
Hydraulic Motor w/2 bolt flange-150 RPM (103-1036 )
Cap Screw 1/2" x 2" Gr 5 for 2-Bolt Motor
Lock Washer 1/2"
Adaptor, Heavy Duty, Hardware Included
Screw, Socket Head 1/4"-20 x 1" with locking plug
Button Shield
Nut, Nylon Lock, 1/2"
Spacer 5/16" x 5/8"-Hose Clamp
Key
Set Screw 1/4"-20 x 1/4"-Adaptor
Washer, Williams, 3/8"
Washer, Split Lock, 1/4"
30162-B
Seal Kit (Motor # 103-XXXX-005/006)
30162-D
Seal Kit (Motor # 103-XXXX-008, 009, 010)
*Power Source with SN#1675 and lower order complete set shown as above.
*Handle SN#5562 and lower order CO-2BF# as replacements.
Page P-6
2
1
1
1
1
2
2
2
2
1
2
1
1
3
1
1
1
1
1
1
1
1
2
2
1
1
1
2
1
1
1
1
1
TWO-MAN HANDLE
-8
-5
-7
-2
16 -
- 18
24 -
30- 16
-6
- 31
26
/
17
\
26
\
- 27
12
\
13 - 14
-3
- 15
11 -
- 28
20 25
\
23
/
19 -9
17 -33
-4
32
/
21--
- 34
- 10
- 35
- 29
Page P-7
1101
TWO-MAN HANDLE
WARNING: For power source serial numbers from H-0001 through H-3252, do not exceed the
following maximum hose assembly lengths. Longer hose assemblies may allow
the torque tube to uncouple, causing serious personal injury.
ITEM
PART #
DESCRIPTION
2
3
4
5
30102-A
*30250-H
*30251-H
30120-A2
30120-L
6
30296
30287
30275
30275-2
5076
9026-KEP
10304
30179
30180-A
30190
3002
30183
30188
3002-KEP
30191
30191-S2
30278
6532
35312
30272
30010
30271-A
30178-A
30273-A
30274-A
3010-9
30198
9058-1
30158
30182
30194
9021
10520
9025
Hose-Valve to Power/Valve to Return, 36" max. overall length
Disconnect Coupling-Female
Disconnect Coupling-Male
Hose-Valve to Motor 24"
Hose-Valve to Motor 22 1/2"
NOTE: SN H-163 & lower order Part #30105
Fitting-Pipe Swivel-Female (O-Ring)
Fitting, NPT
Throttle Valve
Seal Kit (Valve)
Cap Screw 1/4" x 2" USS GR 5
Nut 1/4" KEP (Nut w/ Lock Washer)
Washer, 1/4", Standard Flat
Cotter Key 3/32" x 5/8"
Throttle Lever
Two-Man Handle-Spider
Bolt 5/16" x 1 1/2" USS GR 2-Hose Bracket
Clamp-Hose
Pushnut, Locking Washer
Nut 5/16" KEP (Nut w/ Lock Washer)
Hydraulic Motor w/ 2 bolt flange-220 RPM (103-1035 )
Hydraulic Motor w/ 2 bolt flange-150 RPM (103-1036 )
Hydraulic Motor w/ 2 bolt flange-60 RPM (101-1040 )
Bolt 1/2" X 2" GR 5-Motor Mounting
Lock Washer 1/2"
Adaptor, Heavy Duty, hardware included
Cap Screw 1/4"-20 x 1" w/Locking Plug
Handle-Hose Anchor 18"
Throttle Linkage
Handle-Throttle Mount 18"
Handle-Bare 18"
Screw 5/16" x 2" USS GR 2-Handle
Spacer 5/16" x 5/8"-Hose Clamp
Button Shield
Nut, Nylon Lock, 1/2"
Key
Handle Grip-Two-Man Handle
Set Screw-Adaptor
Washer, Williams, 3/8"
Washer, Split Lock, 1/4"
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
QTY
30162-B
Seal Kit (Motor # 103-XXXX-005/006)
30162-D
Seal Kit (Motor # 103-XXXX-008, 009, 010)
*Power Source with SN#1675 and lower order complete set shown as above.
*Handle SN# 5562 and lower order CO-2BF# as replacements.
Page P-8
2
1
1
1
1
2
2
1
2
2
1
1
1
1
1
1
2
7
1
1
1
2
2
1
1
1
1
1
2
4
1
2
2
1
4
1
1
1
ANCHOR HANDLE
7-
-9
812 - 20
\
8
14 -
5-
26 -
13 -
- 17
- 28
- 18
- 27
10 - 15
6-
- 16
22 \
19
21 -
2-
- 25
I
29
23--
330-11-31--
4-
24--
Page P-9
1101
ANCHOR HANDLE
ITEM
PART #
DESCRIPTION
QTY
WARNING: For power source serial numbers from H-0001 through H-3252, do not exceed the
following maximum hose assembly lengths. Longer hose assemblies may allow
the torque tube to uncouple, causing serious personal injury.
2
3
4
5
30102-A
**30250-H
**30251-H
30115
30120-A
6
30296
30287
5076
30188
30275
30275-2
9026
10304
30178-A
30179
30180-A
30276-A
9034
3010-9
30183
3002-KEP
30278
30191-S2
30191
6532
35312
30272
30010
9058-1
30158
30198
30182
9021
10520
9025
Hose-Valve to Power/Valve to Return, 36" max. overall length
Disconnect Coupling-Female
Disconnect Coupling-Male
Hose-Valve to Motor 15 1/2"
Hose-Valve to Motor 19 1/2"
NOTE: SN#163 & lower order Part #30103
Fitting-Female (O-Ring)
Fitting, NPT
Cap Screw 1/4" x 2" USS GR 5-Valve Mounting
Pushnut, Locking Washer
Throttle Valve
Seal Kit (Valve)
Nut 1/4" KEP (Nut w/ Lock Washer)
Washer, 1/4" Standard
Throttle Linkage
Cotter Key 3/32" x 5/8"
Throttle Lever
Anchor Handle ONLY
Leg Pad
Set Screw 5/16" x 2" GR 2-Hose Clamp
Clamp-Hose
Nut 5/16" KEP (Nut w/ Lock Washer)
Hydraulic Motor w/ 2 bolt flange-60 RPM (101-1040 )
Hydraulic Motor w/ 2 bolt flange-150 RPM (103-1035 )
Hydraulic Motor w/ 2 bolt flange-220 RPM (103-1036 )
Bolt, 1/2" x 2" GR 5-MotorMounting
Lock Washer 1/2"
Adaptor, Heavy Duty, includes hardware
Screw, Socket Head, 1/4"-20 x 1" with locking plug
Button Shield
Nut, Nylon Lock, 1/2"
Spacer 5/16" x 5/8"
Key
Set Screw-Adaptor
Washer, Williams, 3/8"
Washer, Split Lock, 1/4"
*30161
*30161-A
30162-B
30162-D
Seal Kit 60023 (Motor # 101-XXXX-007)
Seal Kit 60036 (Motor # 101-XXXX-005)
Seal Kit (Motor # 103-XXXX-005/006)
Seal Kit (Motor # 103-XXXX-008, 009, 010)
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
2
1
1
1
1
2
2
2
2
1
1
2
1
1
1
1
1
3
1
1
1
1
1
1
2
2
1
1
1
2
1
1
1
1
1
*When ordering Flange or Seal Kit, you must specify motor serial number in order to obtain correct parts.
**Power Source with SN#1675 and lower order complete set as shown above.
*Handle SN#5562 and lower must order CO-2BF# as replacements
Page P-10
1101
AUGERS & ACCESSORIES
ITEM
PART# DESCRIPTION
1
1.5X42-SSS
2.5X42B
2.5X42SP
2X36-SSS
2X42-SSS
3X36-SSS
3X42-SSS
4X36-SSS
4X42-SSS
5X36-SSS
5X42-SSS
6X36-SSS
6X42-SSS
7X36-SSS
7X42-SSS
8X36-SSS
8X42-SSS
9X36-SSS
9X42-SSS
10X36-SSS
10X42-SSS
12X36-SSS
12X42-SSS
14X36-SSS
14X42-SSS
16X36-SSS
16X36-SSSF
16X42-SSSF
1-1/2" X 42" Auger, Snap-on with Screw-on Point
2-1/2" X 42" Bucket Auger, Snap-on
2-1/2" x 42" Spiral Barrel Auger (Soil Sampling)
2" X 36" Auger, Snap-on with Screw-on Point
2" X 42" Auger, Snap-on with Screw-on Point
3" X 36" Auger, Snap-on with Screw-on Point
3" X 42" Auger, Snap-on with Screw-on Point
4" X 36" Auger, Snap-on
4" X 42" Auger, Snap-on
5" X 36" Auger, Snap-on
5" X 42" Auger, Snap-on
6" X 36" Auger, Snap-on
6" X 42" Auger, Snap-on
7" X 36" Auger, Snap-on
7" X 42" Auger, Snap-on
8" X 36" Auger, Snap-on
8" X 42" Auger, Snap-on
9" X 36" Auger, Snap-on
9" X 42" Auger, Snap-on
10" X 36" Auger, Snap-on
10" X 42" Auger, Snap-on
12" X 36" Auger, Snap-on
12" X 42" Auger, Snap-on
14" X 36" Auger, Snap-on
14" X 42" Auger, Snap-on
16" X 36" Auger, Snap-on
16" X 36" Auger, Snap-on, Full Flighted
16" X 42" Auger, Snap-on, Full Flighted
2
9023-4
9023-6
9023-8
9023-9
9023-12
9023-14
9023-16
Blade for 4" & 5" Augers
Blade for 6" & 7" Augers
Blade for 8" Augers
Blade for 9" & 10" Augers
Blade for 12" Augers
Blade for 14" Augers
Blade for 16" Augers
3
9027
9027-16
Point, Standard, Fits 4" thru 12" Augers
Point, Standard, Fits 14" and 16" Augers
4
9058
Spring & Button
5
9023-S4
9023-S9
9023-S12
9023-S16
Cap Screw & Nut w/Lockwasher, 4" thru 8" Blades
Cap Screw & Nut w/Lockwasher, 9" thru 10" Blades
Cap Screw & Nut w/Lockwasher, 12" Blades
Cap Screw & Nut w/Lockwasher, 14" & 16" Blades
6
9027-7
Cap Screw & Nut w/Lockwasher, Standard Points
STANDARD AUGER
1
--12
--2
5
Page P-11
1093
ITEM
STANDARD AUGER
WITH CARBIDE POINT
7
9023-C1.5
9023-C2
9023-C3
9023-C4
9023-C5
9023-C6
9023-C7
9023-C8
9023-C9
9023-C10
9023-C12
Blade, Screw-on, w/Carbide for 1-1/2" Augers
Blade, Screw-on, w/Carbide for 2: Augers
Blade w/Carbide for 3" Auger, Inc. Mtng. Bolts/Nuts
Blade w/Carbide for 4" Auger, " " "
Blade w/Carbide for 5" Auger, " " "
Blade w/Carbide for 6" Auger, " " "
Blade w/Carbide for 7" Auger, " " "
Blade w/Carbide for 8" Auger, " " "
Blade w/Carbide for 9" Auger, " " "
Blade w/Carbide for 10" Auger, " " "
Blade w/Carbide for 12" Auger, " " "
8
9027-8S
Cap Screw & Lock Nut for Carbides (2 ea.)
9
6X36-SSP
6X42-SSP
7X36-SSP
7X42-SSP
8X36-SSP
8X42-SSP
9X36-SSP
9X42-SSP
10X36-SSP
10X42-SSP
12X36-SSP
12X42-SSP
6" x 36" Snap-on Auger w/Pengo Point & Blade
6" x 42" Snap-on Auger w/Pengo Point & Blade
7" x 36" Snap-on Auger w/Pengo Point & Blade
7" x 42" Snap-on Auger w/Pengo Point & Blade
8" x 36" Snap-on Auger w/Pengo Point & Blade
8" x 42" Snap-on Auger w/Pengo Point & Blade
9" x 36" Snap-on Auger w/Pengo Point & Blade
9" x 42" Snap-on Auger w/Pengo Point & Blade
10" x 36" Snap-on Auger w/Pengo Point & Blade
10" x 42" Snap-on Auger w/Pengo Point & Blade
12" x 36" Snap-on Auger w/Pengo Point & Blade
12" x 42" Snap-on Auger w/Pengo Point & Blade
10
9023-P35
9023-P35HS
9023-P1336
Blade, Pengo #35 (1 per 6" & 7" Auger, 2 per 8"-12")
Blade, Pengo #35HFF Hardsurfaced (Both sides)
Blade, Pengo #1336 w/Carbide
11
9027-P
9027-PC
Point, Pengo #SB25
Point, Pengo #SB-25C w/Carbide
12
FS-3
FS-4
FS-5
FS-6
FS-7
FS-8
FS-9
FS-10
FS-12
FS-14
FS-16
Flighting, replacement 3" x 37" or 60" Section
Flighting, 4" x 30" or 37" Section
Flighting, 5" x 30" or 37" Section
Flighting, 6" x 30" or 37" Section
Flighting, 7" x 30" or 37" Section
Flighting, 8" x 30" or 37" Section
Flighting, 9" x 30" or 37" Section
Flighting, 10" x 30" or 37" Section
Flighting, 12" x 37" Section
Flighting, 14" x 37" Section
Flighting, 16" x 16" Section
13
9062
9062-H
Auger Top for 4" thru 10" Augers
Auger Top for 12" thru 16" Augers
14
9062-1
9062-2
Extension Bottom for 4" thru 10" Extensions
Extension Bottom for 12" thru 14" Extensions
-7
8
Optional Carbide
Blade
Specify -SSC when
ordering Auger
PENGO AUGER
---4
9
-12
-10
-11
AUGER REPAIR PARTS
Must be welded.
0196
PART# DESCRIPTION
Page P-12
ITEM
PART# DESCRIPTION
EXTENSION
13--
---4
15
15
9054
9054-A
9054-S1.5X36
9054-S2X36
9054-S3X36
9054-3X36
9054-4X36
9054-5X36
9054-6X36
9054-7X36
9054-8X36
9054-9X36
9054-10X36
9054-12X36
9054-14X36
36" Tube Type Snap-on Extension
18" Tube Type Snap-on Extension
1-1/2" x 36" Screw-on Ext.(Must use Screw-on Agr)
2" x 36" Screw-on Ext.(Must use Screw-on Auger)
3" x 36" Screw-on Ext.(Must use Screw-on Auger)
3" x 36" Snap-on Extension
4" x 36" Snap-on Extension
5" x 36" Snap-on Extension
6" x 36" Snap-on Extension
7" x 36" Snap-on Extension
8" x 36" Snap-on Extension
9" x 36" Snap-on Extension
10" x 36" Snap-on Extension
12" x 36" Snap-on Extension
14" x 36" Snap-on Extension
16
1.5X36-HSL
1.5X42-HSL
2X36-HSL
2X42-HSL
3X36-HSL
3X42-HSL
1-1/2" x 36" Auger/Extension, Hex, Less Point
1-1/2" x 42" Auger/Extension, Hex, Less Point
2" x 36" Auger/Extension, Hex, Less Point
2" x 42" Auger/Extension, Hex, Less Point
3" x 36" Auger/Extension, Hex, Less Point
3" x 42" Auger/Extension, Hex, Less Point
17
9027-H1.5
9027-H2
9027-H3
Point, Hex, 1-1/2"
Point, Hex, 2"
Point, Hex, 3"
9041-2
9041-3
Pin, Locking, 1-1/2" & 2" Hex Auger/Extensions
Pin, Locking, 3" Hex Auger/Extensions
9040
Spring Ball Plunger, (replace as needed)
30272
30272-HD
9051-GHAS
9061
9061-H
9061-H3
9061-A
Adaptor, Keyed
Adaptor, Keyed, Heavy Duty
Adaptor, Ground Hog to Keyed Adaptor
Adaptor, Screw-on Auger to Keyed Adaptor
Adaptor, 1-1/2" & 2" Hex Auger to Keyed Adaptor
Adaptor, 3" Hex Auger to Keyed Adaptor
Adaptor, Drill Chuck to Keyed Adaptor
---14
HEX AUGER/EXTENSION
16
17
ADAPTORS
Auger to Transmission
Page P-13
IMPORTANT: All nuts, fasteners, and fittings must be kept tightened. Refer to
torque chart for proper assembly torque.
TORQUE INFORMATION
HEX HEAD
TYPE
GRADE
5
SOCKET
GRADE
8
WRENCH SIZE
WRENCH SIZE
inch
SIZE
No. 4
8 in lb
12 in lb
1/4"
12 in lb
3/32"
No. 6
16 in lb
23 in lb
5/16"
21 in lb
7/64"
No. 8
30 in lb
41 in lb
11/32"
42 in lb
9/64"
No.10
43 in lb
60 in lb
3/8"
60 in lb
5/32"
1/4"
8 ft lb
12 ft lb
7/16"
12 ft lb
3/16"
5/16"
17 ft lb
25 ft lb
1/2"
24 ft lb
1/4"
3/8"
30 ft lb
45 ft lb
9/16"
43 ft lb
5/16"
7/16"
50 ft lb
70 ft lb
5/8"
69 ft lb
3/8"
1/2"
75 ft lb
110 ft lb
3/4"
105 ft lb
3/8"
9/16"
110 ft lb
150 ft lb
13/16"
158 ft lb
-----
5/8"
150 ft lb
220 ft lb
15/16"
195 ft lb
1/2"
3/4"
260 ft lb
380 ft lb
1-1/8"
353 ft lb
5/8"
HYDRAULIC FITTINGS
0196
SIZE
TORQUE
1/4 NPT
3/8 NPT
1/2 NPT
3/4 NPT
25 ft.lb.
50 ft.lb
75 ft.lb.
110 ft.lb.
SIZE
7/16-20
9/16-18
3/4-16
7/8-14
1-1/16-12
SAE
SAE
SAE
SAE
SAE
TORQUE
O-Ring
O-Ring
O-Ring
O-Ring
O-Ring
12 ft.lb.
20 ft.lb.
35 ft.lb.
50 ft.lb.
70 ft.lb.
TH I N K
SAFET Y
FI RST!
P.O. BOX 840
LIVINGSTON, TEXAS 77351
PH# 936/327-3121
FAX# 936/327-4025
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising