MEGANE
MEGANE
DRIVER’S HANDBOOK
RENAULT recommends ELF
ELF has developed a complete range of lubricants for RENAULT:
f engine oils
f manual and automatic gearbox oils
Warning: to ensure the engine operates optimally, the use
of a lubricant may be restricted to certain vehicles. Please
refer to your maintenance document.
Benefiting from the research applied to Formula 1,
lubricants are very high-tech products.
Photo credit: Total/DPPI Imacom group
Updated with the help of RENAULT’s technical
teams, this range is perfectly compatible with the
specific features of the brand’s vehicles.
f ELF lubricants enhance
your vehicle’s performance significantly.
RENAULT recommends approved ELF lubricants for oil changes and top-ups.
Contact your RENAULT Dealer or visit www.lubrifiants.elf.com
Une marque de
Welcome to your new vehicle
This Driver’s Handbook contains the information necessary:
– for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and
the technical developments it incorporates.
– to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance.
– to enable you to deal quickly with minor faults not requiring specialist attention.
It is well worth taking a few minutes to read this handbook to familiarise yourself with the information and guidelines it contains
about the vehicle and its functions and new features. If certain points are still unclear, our Network technicians will be only too
pleased to provide you with any additional information.
The following symbol will help you when reading this handbook:
To indicate a hazard, danger or safety recommendation.
The descriptions of the models given in this handbook are based on the technical specifications at the time of writing. This handbook covers all items of equipment (both standard and optional) available for these models but whether or not these are
fitted to the vehicle depends on the version, options selected and the country where the vehicle is sold.
This handbook may also contain information about items of equipment to be introduced later in the model year.
Throughout the manual, the “approved Dealer” is your RENAULT Dealer.
Enjoy driving your new vehicle.
Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from the vehicle manufacturer.
0.1
0.2
C
O
N
T
E
N
T
S
Sections
Getting to know your vehicle ...............................
1
Driving
2
...................................................................
Your comfort
.........................................................
3
Maintenance
.........................................................
4
Practical advice
....................................................
......................................
6
...............................................
7
Technical specifications
Alphabetical index
5
0.3
0.4
Section 1: Getting to know your vehicle
RENAULT cards: general information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic locking when driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headrests - Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat belts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional methods of restraint: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
to the front seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
to the rear seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
side protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Child safety: general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
choosing a child seat mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
fitting a child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
deactivating, activating the front passenger airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-assisted steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driving position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
on-board computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vehicle settings customisation menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock and exterior temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Door mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audible and visual signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exterior lighting and signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windscreen washers and wipers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel tank (filling with fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2
1.10
1.14
1.15
1.17
1.22
1.25
1.25
1.29
1.30
1.32
1.35
1.37
1.48
1.51
1.51
1.52
1.56
1.62
1.72
1.73
1.74
1.75
1.76
1.80
1.81
1.84
1.1
RENAULT CARDS: general information (1/2)
The RENAULT card is used
for:
1
1
2
3
4
5
2
3
4
5
Unlocking the doors and tailgate.
Locking all doors and tailgate.
Switching on the lighting remotely.
Unlocking/locking the tailgate
Integrated key.
Special note
The RENAULT “SERVICE” card, on
equipped vehicles, can be identified
by the word “SERVICE” engraved on
the card. Refer to the information on
the RENAULT “SERVICE” card in section 1.
1.2
– locking/unlocking the doors and tailgate (doors, tailgate) and the fuel
filler flap (see the following pages);
– switching on the vehicle lighting remotely (refer to the following pages);
– depending on the vehicle, automatically closing the electric windows
and sunroof remotely (see the information on “Electric windows/Electric
sunroof” in Section 3);
– starting the engine; refer to the information on “Starting the engine” in
Section 2.
Range of the RENAULT card
This varies according to the surroundings. It is important to make sure when
handling the RENAULT card that you
do not lock or unlock the doors by inadvertently pressing the buttons.
When the battery is flat, you can
still lock/unlock and start your vehicle. Refer to the information on
“Locking/unlocking the doors” in
Section 1 and “Starting the engine”
in Section 2.
Battery life
Make sure that the correct battery type
is being used, and that the battery is in
good condition and inserted correctly.
Its service life is approximately two
years: replace it when the message
“Keycard battery low” appears on the
instrument panel (refer to the information on the “RENAULT card: battery" in
section 5).
Driver’s responsibility
Never leave your vehicle
with the RENAULT card
inside and never leave a
child (or a pet) unsupervised, even
for a short while.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or by locking the
doors.
Risk of serious injury.
RENAULT CARDS: general information (2/2)
Access to key 5
Press button 6 and pull on key 5 then
release the button.
Using the key
5
6
Refer to the information on “Locking/
unlocking the doors”.
Once you have accessed the vehicle
using the integrated key, replace it
in its housing in the RENAULT card,
then insert the RENAULT card into
the card reader to start the vehicle.
Replacement: need for an
additional RENAULT Card
If you lose your RENAULT card or
require another, you can obtain one
from an approved dealer.
If a RENAULT card is replaced, it
will be necessary to take the vehicle and all of its RENAULT cards
to an approved dealer to initialise
the system.
You may use up to four RENAULT
cards per vehicle.
Integrated key 5
The integrated key is used to lock or
unlock the front left-hand door if the
RENAULT card does not work:
– when the RENAULT card battery is
drained, flat battery, etc.
– use of devices using the same frequency as the card;
– if the vehicle is located in a zone of
high electromagnetic radiation;
Advice
Avoid leaving the card in hot, cold or
humid areas.
Do not keep the RENAULT card in
a place where it could be bent or
damaged accidentally, such as in a
back pocket of a garment.
1.3
REMOTE CONTROL RENAULT CARD: use
2
1
3
4
Unlocking the doors and
tailgate
Press button 1.
The hazard warning lights flash once
to indicate that the doors have been unlocked.
When unlocking is only active for the
driver’s door, (refer to the information
on the “vehicle settings customisation
menu” in Section 1):
– pressing button 1 unlocks only the
driver’s door and the fuel filler flap;
– pressing button 1 twice unlocks all
the doors and the tailgate.
Locking the doors and
luggage compartment
Unlocking/locking the
luggage compartment only
Press the locking button 2. The hazard
warning lights flash twice to indicate
that the doors have locked. If a door
or the luggage compartment is open
or not properly shut, or if a RENAULT
card is still in the reader, the doors and
luggage compartment lock then quickly
unlock and the hazard warning lights
do not flash.
Press button 4 to unlock/lock the luggage compartment.
If the vehicle has been unlocked
but neither the doors or tailgate are
open, it locks again automatically
after two minutes.
The card buttons are deactivated
when the engine is running.
The flashing status of the hazard
warning lights informs you of the vehicle status:
– one flash indicates that the vehicle is completely unlocked;
– two flashes indicate that the vehicle is completely locked.
1.4
RENAULT card not detected
alarm
If you open a door while the engine
is running and the card is not in the
reader, the message “Keycard not detected” and a beep will warn you. The
warning disappears when the card is inserted in the reader again.
Distance lighting function
The dipped beam headlights, indicator
lights and interior lights come on for approximately 30 seconds when button 3
is pressed. This can be used, for example, to identify the vehicle from a distance when parked in a car park.
Note: pressing button 3 again switches
off the lighting.
RENAULT “HANDS-FREE” CARD: use (1/3)
2
1
Use
On equipped vehicles, in addition to
the functions of the above-mentioned
remote control RENAULT card, it can
be used to lock/unlock without using
the RENAULT card, when it is in access
zone 1.
3
Unlocking the vehicle
With the RENAULT card in the 1 zone,
pass your hand behind a handle 2: the
vehicle will unlock.
In some cases (leaving the vehicle
parked for several days, for example),
you may need to pull handle 2 twice to
unlock the vehicle and open the door.
Pressing the button 3 also unlocks all
the doors and the tailgate.
Recommendations
Do not store the RENAULT card
anywhere it may come into contact with other electronic equipment
(computer, PDA, phone, etc.) as this
could hinder its operation.
The hazard warning lights flash once
to indicate that the doors have been unlocked.
After unlocking the vehicle or the
boot only using the buttons of the
RENAULT card, remote locking and
unlocking in hands-free mode are
deactivated.
To reactivate the hands-free mode:
restart the vehicle.
1.5
RENAULT “HANDS-FREE” CARD: use (2/3)
Locking using button 4
With the doors and luggage compartment closed, press button 4 on the driver’s door handle. The vehicle will lock.
If a door or the tailgate is open or not
closed properly, the vehicle will quickly
lock/unlock.
2
Note: a RENAULT card must be within
the vehicle's access zone (zone 1) to
be able to lock the vehicle using the
button.
4
1
Locking the vehicle
There are three ways to lock the vehicle: remotely, using button 4, or using
the RENAULT card.
Remote locking
With the RENAULT card on you, and
doors and tailgate closed, move away
from the vehicle: it will lock automatically once you have left zone 1.
Note: the distance at which the vehicle
locks depends on the surroundings.
The hazard warning lights flash twice
and a beep sounds to indicate that the
doors have locked.
The beep may be switched off. Consult
an approved Dealer.
If a door or the tailgate is open or not
properly shut, or a card is in the passenger compartment (or the card reader)
the vehicle will not lock. In this situation, no beep sounds and the hazard
warning lights do not flash.
Special note
If you wish to check that the doors are
locked after locking using button 4, you
have approximately three seconds to
try the door handles without unlocking
them.
After this delay, the hands-free mode
is activated once again and any movement of a handle will unlock the vehicle.
If the vehicle is fitted with remote window closing, two quick presses on button 4 automatically causes all the windows to close
and the doors to lock (please see the information on “Electric windows, Electric sunroof” in Section 3).
1.6
RENAULT “HANDS-FREE” CARD: use (3/3)
5
6
With the engine running, if having
once opened and closed a door, the
card is no longer in the passenger compartment, the message “Keycard not
detected” (accompanied by a warning
beep once the speed passes a threshold value) will tell you that the card is no
longer in the vehicle. This avoids you
driving away after having dropped off a
passenger who has the card, for example.
The warning disappears when the card
is detected again.
Locking using the RENAULT card
Special features
With the doors and luggage compartment closed, press button 5: the vehicle will lock.
The vehicle will not lock if:
The hazard warning lights flash twice
to indicate that the doors have locked.
– a card is still in zone 6 (or in the card
reader) and no other card is in the
external detection zone.
Note: the maximum distance at which
the vehicle locks depends on the surroundings.
– a door or the tailgate is open or not
properly closed;
After locking/unlocking the vehicle
or the luggage compartment only
using the buttons on the RENAULT
card, remote locking and unlocking
in hands-free mode are deactivated.
To reactivate the “hands-free” mode:
restart the vehicle.
1.7
RENAULT CARD: deadlocking
To deactivate deadlocking
Unlock the vehicle using button 1 on
the RENAULT card.
1 2
3
If the vehicle is equipped with a deadlocking function, this allows you to lock
the opening elements and to prevent
the doors from being unlocked using
the interior handles (for example, by
breaking the window and then trying to
open the door from the inside).
To activate deadlocking
You can choose between two deadlocking activation modes:
– press button 2 twice in quick succession;
– or, press the button on the driver’s
door handle 3 twice in quick succession.
The hazard warning lights flash five
times to indicate locking.
Never use deadlocking if
someone is still inside the
vehicle.
1.8
The hazard warning lights flash once to
indicate that the doors have been unlocked.
Activating deadlocking also remotely closes the windows and/or
the electric sunroof, on equipped
vehicles.
After activating the deadlocking
function using button 2, remote
locking and unlocking in hands-free
mode are deactivated.
To reactivate the “hands-free” mode:
restart the vehicle.
RENAULT CARD “SERVICE”
Deactivation of the
“SERVICE” mode
1
2
There are two possibilities:
3
4
– Press a button on the RENAULT
card (not the RENAULT “SERVICE”
card);
– start the engine with a RENAULT
card (not the RENAULT “SERVICE”
card). With the card in reader 4,
press button 5.
5
If the vehicle is equipped with this
card, it can be identified by the word
“SERVICE” engraved on the card.
In certain situations, you may wish to
entrust your vehicle to a third party
(parking valet, mechanic, etc.) whilst
restricting its operation.
The RENAULT “SERVICE” card enables the vehicle to be locked but only
allows the driver's door to be unlocked
and the engine to be started.
Activation of the “SERVICE”
mode.
Insert the RENAULT “SERVICE” card
into the card reader 4. All the vehicle
opening elements lock (except the driver’s door).
If they do not, with the engine
switched off, press button 1 (all the
doors and the tailgate lock, with the exception of the driver’s door) or 2 (the
entire vehicle locks) on the RENAULT
“SERVICE” card.
The interior locking/unlocking
switch 3 is deactivated while the vehicle is in use with the RENAULT
“SERVICE” card.
Each vehicle only has
RENAULT “SERVICE” card.
one
When using a RENAULT “SERVICE”
card, the other cards retain all their
functions.
1.9
OPENING AND CLOSING THE DOORS (1/2)
Card reminder buzzer
2
When the driver’s door is opened and
the card is still in the reader, the message “Please remove keycard” appears
on the instrument panel, accompanied
by a beep.
Door/tailgate open buzzer
1
Opening the doors from the
outside
With the doors unlocked or the “handsfree” RENAULT card in your possession, hold handle 1 and pull it towards
you.
In some cases, it may be necessary to
pull the handle twice to open the door.
Opening from the inside
Pull on the handle 2.
Lights-on reminder buzzer
If you have switched off the ignition
and left the lights switched on, a reminder buzzer will sound when a door
is opened.
If an opening element (door or boot) is
open or not properly closed, as soon
as the vehicle reaches a speed of approximately 6 mph (10 km/h), the message “Boot open” or “Door open” (depending on which is open) will appear
on the instrument panel accompanied
by a warning light.
Special note
After switching off the engine, the lights
and any accessories that are in operation (radio, etc.) will continue to operate.
They stop as soon as the driver’s door
is opened.
As a safety precaution,
the doors should only be
opened or closed when the
vehicle is stationary.
1.10
OPENING AND CLOSING THE DOORS (2/2)
Safety of rear occupants
The driver can enable operation of the rear doors
and, depending on the vehicle, the electric windows by pressing switch 3 on the side with the illustration.
3
Child safety
Vehicle with switch 3
Press switch 3 to enable the
rear doors to be opened. If the vehicle
is equipped with electric rear windows,
this action will also enable their use.
The indicator light in the switch lights up
to confirm that the locks have been activated.
Ç
Note: if there is a system fault, the message “Check child safety device” is displayed on the instrument panel: please
contact an authorised dealer.
Depending on the vehicle, in the
event of a fault:
– a beep sounds;
– a message is displayed on the instrument panel;
– the integrated indicator does not
light up.
If the battery has been disconnected, press switch 3 as indicated
in the image to lock the rear doors.
4
Vehicle with manual door locking
To make it impossible for the rear doors
to be opened from the inside, move
lever 4 on each door and check from
the inside that the doors are securely
locked.
Driver’s responsibility when parking or stopping the vehicle
Never leave an animal, child or adult who is not self-sufficient alone on
your vehicle, even for a short time.
They may pose a risk to themselves or to others by starting the engine,
activating equipment such as the electric windows or by locking the doors.
Also, in hot and/or sunny weather, please remember that the temperature inside
the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS INJURY.
1.11
LOCKING/UNLOCKING THE DOORS (1/2)
Locking/Unlocking the doors
from the outside
This is done using the RENAULT Card;
see the “RENAULT Card” information in
Section 1.
In certain cases, the RENAULT card
may not work:
– if the RENAULT card battery is weak,
flat, etc.
3
A
1
2
– if equipment operating on the same
frequency as the card (mobile
phones, etc.) is used;
– vehicle located in a high electromagnetic radiation zone.
It is then possible:
– to use the key integrated into the
card to unlock the front left-hand
door;
– to lock each of the doors manually;
– to use the interior door locking/unlocking control (refer to the following
pages).
1.12
Using the key integrated in
the RENAULT card
– Remove cover A from the left-hand
door (using the end of key 2) in
notch 1;
– move it upwards to remove cover A;
– insert the key 2 into the lock of the
front left-hand door and lock or
unlock.
Locking the doors manually
Turn screw 3 with the door open (using
the end of the key) and close the door.
This means that the doors are then
locked from the outside.
The doors may then only be opened
from the inside or by using the key in
the front left-hand door.
LOCKING/UNLOCKING THE DOORS (2/2)
4
Locking the doors without
the RENAULT card
Door and tailgate status
indicator
For example, in the event of a discharged battery or the RENAULT card
temporarily not working, etc.
When the ignition is on, the indicator
light integrated in switch 4 informs you
of the status of the doors and tailgate:
With the engine switched off and a
door or tailgate open, press and hold
switch 4 for more than five seconds.
– indicator light on, the doors and tailgate are locked,
When the door is closed, all the doors
and the tailgate will be locked.
Interior locking/unlocking
door control
Unlocking the vehicle from the outside
is only possible with the RENAULT card
in the vehicle's access zone or using
the key integrated in the RENAULT
card.
Switch 4 controls the doors, tailgate
and, depending on the vehicle, the fuel
filler flap simultaneously.
When you lock the doors, the indicator
light remains lit and then goes out.
Never leave your vehicle
with the RENAULT card
inside.
If a door or the tailgate is open or not
closed properly, the doors and tailgate
lock/unlock quickly.
If transporting an object with the tailgate open, you can still lock the doors:
with the engine stopped, press and
hold switch 4 for more than five seconds to lock the other doors.
– indicator light off, the doors and tailgate are unlocked.
After locking/unlocking the vehicle
or the tailgate only using the buttons on the RENAULT card, remote
locking and unlocking in hands-free
mode are deactivated.
To reactivate the “hands-free” mode:
restart the vehicle.
Driver’s responsibility
If you decide to keep the
doors locked when you are
driving, remember that it
may be more difficult for those assisting you to gain access to the
passenger compartment in the
event of an emergency.
1.13
AUTOMATIC LOCKING WHEN DRIVING
Operating faults
You can decide whether you want to
activate this function.
1
Operating principle
After the vehicle is started, the system
automatically locks the doors when you
are driving at approximately 6 mph
(10 km/h) and over.
The door can be unlocked:
– by pressing the door unlocking
button 1.
– by opening a front door (vehicle stationary).
Note: if a door is opened or closed,
it will automatically lock again when
the vehicle reaches a speed of 6 mph
(10 km/h).
Activating/deactivating the
function
Refer to “Vehicle settings customisation
menu” in Section 1, regarding the “Auto
door locking while driving” function:
=
<
Driver’s responsibility
If you decide to keep the
doors locked when you are
driving, remember that it
may be more difficult for those assisting you to gain access to the
passenger compartment in the
event of an emergency.
1.14
function activated
function deactivated.
If you experience an operating fault (no
automatic locking, the indicator light incorporated in button 1 does not light up
when trying to lock the doors and tailgate, etc.), firstly check that the doors
and tailgate are properly closed. If they
are closed correctly, contact an approved dealer.
FRONT HEADRESTS
To adjust the angle of the
headrest
2
1
Depending on the vehicle, tilt section A
towards or away from you to the required position.
A
3
To remove the headrest
Raise the headrest to its highest position (tilt the seatback backwards if
necessary). Press button 1 and lift the
headrest to release it.
To refit the headrest
To raise the headrest
Pull the headrest upwards to the desired height.
To lower the headrest
Press button 2 and guide the headrest
down to the desired height.
Pull out the headrest rods 3 as far as
possible by pulling from the top. Take
care to ensure they are clean and correctly aligned and, if there are any problems, check that the notches are facing
forwards.
Insert the headrest rods into the holes
(tilt the seatback backwards if necessary).
Lower the headrest until it locks, press
button 1 and lower the headrest as far
as possible.
Check that each headrest rod 3 is securely locked in the seatback by trying
to pull them up or push them down.
The three upper positions can
be manipulated without pressing
button 2. However, it is preferable to
press this button to lower the headrest.
The headrest is an important safety component:
ensure that it is in place and
in the correct position. The
distance between your head and the
headrest and the distance between
the head and section A should be
as small as possible.
1.15
REAR HEADRESTS
2
B
1
A
Position for use
To refit the headrest
Raise or lower the headrest while pulling it towards the front of the vehicle.
Insert the headrest rods into the
sleeves, and lower the headrest to the
first notch.
To remove the headrest
Press tabs A of rods 1 and 2 simultaneously and remove the headrest.
Note: on the three door version, first
lower the bench seatback (refer to the
information on the “Rear seat functions”
in Section 3).
1.16
Storage position
Lower the headrest as far as possible, then press tab 2 and lower it completely.
When the headrest is set at the
lowest position (position B) this is
for storage only: it should not be in
this position when a seat is occupied.
The headrest is a safety
component. Ensure that it is
fitted and in the correct position: the top of your head
should be in line with the top of the
headrest.
FRONT SEATS WITH MANUAL CONTROL (1/2)
To tilt the seatback
3
Turn control knob 3 to the required position.
Heated seats
2
(depending on vehicle)
1
4
To move the seat forwards or
back
Lift handle 1 to release. Release the
handle once the seat is in the correct
position and ensure that the seat is fully
locked into position.
To raise or lower the seat
base
Move lever 2 as many times as necessary upwards or downwards.
With the engine running, turn control 4
to either position I, II or III (depending
on the temperature required). An indicator light on the instrument panel
lights up once the front seat heating
system is operating.
The system, which has a thermostat,
decides whether or not the heating is
needed, according to the position selected.
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
We would advise you not to recline
the seatbacks too far to ensure that
the effectiveness of the seat belts is
not reduced.
Nothing should be placed on the
floor (area in front of driver) as such
objects may slide under the pedal
during braking manoeuvres, thus
obstructing its use.
1.17
FRONT SEATS WITH MANUAL CONTROL (2/2)
5
6
To adjust the lumbar support
on the driver’s seat
Lower handle 5 to increase the support
and lift to decrease it.
Table function
Depending on the vehicle, the passenger seatback may be folded down onto
the seat base to create a table.
Lower the headrest, move the seat
back, tilt handle 6 and completely lower
the seatback.
For your safety, attach any
transported objects when
the seat is in the table position.
1.18
When the front seat is in
table position, the front passenger air bag must be disabled (see information on
“Child safety: activating/deactivating the front passenger air bag” in
Section 1).
Risk of serious injury caused by
items resting on the seatback table
which may be dislodged when the
air bag is deployed.
The label (on the dashboard) and
the markings (on the windscreen)
remind you of these instructions.
FRONT SEATS WITH ELECTRIC CONTROL
Switch 3 is used for adjusting the seatback and switch 4 is used for adjusting
the seat squab.
On equipped vehicles, buttons 1 are
used to store the chosen driving position (refer to the following page).
1
Adjusting the seat squab:
Lower handle 5 to increase the support
and lift to decrease it.
4
Adjusting the seatback:
To tilt the seatback, move the top of
switch 3 forwards or backwards.
Heated seats
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
5
3
– To move the seat forwards or back
Move switch 4 forwards or backwards.
– To raise or lower the seat base
Move the switch 4 upwards or downwards.
Adjusting the lumbar support
on the driver’s seat:
2
(depending on vehicle)
With the engine running, turn control 2
to either position 1, 2 or 3 (depending
on the temperature required). An indicator light on the instrument panel
lights up once the front seat heating
system is operating.
The system, which has a thermostat,
decides whether or not the heating is
needed, according to the position selected.
We would advise you not
to recline the seatbacks too
far to ensure that the effectiveness of the seat belts is
not reduced.
Nothing should be placed on the
floor (area in front of driver) as such
objects may slide under the pedal
during braking manoeuvres, thus
obstructing its use.
1.19
FRONT SEATS WITH ELECTRIC CONTROL WITH STORAGE OF SETTINGS
It is possible to store three driving positions.
Recalling a stored driving
position
A driving position includes the settings
for the seat base and seatback of the
driver’s seat.
With the vehicle stationary, briefly
press button 1, 2 or 3 depending on the
required stored driving position.
The system operates:
1
2
– with the “hands-free” card detected or, depending on the vehicle,
RENAULT card in the card reader;
– when the driver’s door is opened.
3
4
5
Note: recall of the stored driving position is interrupted if one of the seat
adjustment buttons is pressed during
recall.
When driving, it is not possible to
recall a driving position.
Storing your driving position
– Adjust the seat using switches 4
and 5 (see previous page);
– press one of buttons 1, 2 or 3 until a
beep is heard: the driving position is
stored;
– to store other driving positions
repeat this procedure with the other
buttons.
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
1.20
We would advise you not
to recline the seatbacks too
far to ensure that the effectiveness of the seat belts is
not reduced.
Nothing should be placed on the
floor (area in front of driver) as such
objects may slide under the pedal
during braking manoeuvres, thus
obstructing its use.
ACCESS TO REAR SEATS, THREE-DOOR VERSION
1
1
2
3
4
Manually controlled seats
Lift handle 1 and slide the seat forward.
To return the seat to its original position,
bring the seatback back into position.
Do not move handle 1 and handle 2
or switch 4 at the same time.
Locking the seats
When a person, an object or a child
seat prevents the front seats from locking, perform the following operations:
– ask all of the passengers to leave
the vehicle and remove any bulky
objects from the rear seats;
– lock the seat(s) in the initial position
again;
– move the seat(s) forwards in order to
create sufficient space;
– ask the passengers to get back into
the vehicle, and refit the child seat or
objects on the rear seats.
Electrically controlled seats
Lift handle 1 and tilt the seatback completely: the seat moves forward.
To return the seat to its original position,
bring the seatback back up. The seat
returns to its original position.
Special note: if the seatback is
tilted over the rear bench seat, only
use control 3 to return it to the driving position.
Never use handle 1 as it is not designed for this purpose: there is a
risk of damage to the mechanism.
Check that no object or
person prevents the front
seat from locking. If so,
remove any obstacles
behind the front seats. Adjust the
seat to allow sufficient room in the
rear. The rear occupants/objects
should then return to the vehicle.
Repeat the above until the seat is
locked correctly.
Risk of seat moving on its runners
during vehicle acceleration or braking.
1.21
SEAT BELTS (1/3)
Always wear your seat belt when travelling in your vehicle. You must also
comply with the legislation of the particular country you are in.
Before starting, first adjust your driving position, then ask all occupants
to adjust their seat belts to ensure
optimum protection.
Adjusting your driving
position
Make sure that the rear bench seat
is locked in position correctly so that
the rear seat belts will operate efficiently. Refer to the information on
the “Rear bench seat” in Section 3.
Incorrectly adjusted or
twisted seat belts may
cause injuries in the event
of an accident.
Use one seat belt per person,
whether child or adult.
Even pregnant women should wear
a seat belt. In this case, ensure that
the lap belt is not exerting too much
pressure on the abdomen, but do
not allow any slack.
1.22
– Sit well back in your seat (having
first removed your coat or jacket).
This is essential to ensure your back
is positioned correctly;
– adjust the distance between the
seat and the pedals. Your seat
should be as far back as possible
while still allowing you to depress
the clutch pedal fully. The seatback
should be adjusted so that your arms
are slightly bent when you hold the
steering wheel;
– adjust the position of your headrest. For maximum safety, your head
must be as close as possible to the
headrest;
– adjust the height of the seat. This
adjustment allows you to select the
seat position which offers you the
best possible view;
– adjust the position of the steering
wheel.
1
2
Adjusting the seat belts
Sit with your back firmly against the
seatback.
Shoulder strap 1 should be as close as
possible to the base of the neck but not
on it.
Lap belt 2 should be worn flat over the
thighs and against the pelvis.
The belt should be worn so that it is
as close as possible to your body, i.e.:
avoid wearing heavy clothing or keeping bulky objects under the belts, etc.
SEAT BELTS (2/3)
Front seat belt reminder
warning light
This lights up on the central display
when the engine is started then, if the
driver’s or front passenger’s seat belt
(if this seat is occupied) is not fastened
and the vehicle has reached approximately 12 mph (20 km/h), it flashes and
a bleep sounds for around 2 minutes.
ß
1
4
3
4
Locking
Unwind the belt slowly and smoothly
and ensure that buckle 3 locks into
catch 4 (check that it is locked by pulling on buckle 3). If the belt jams, allow
it to return slightly before attempting to
unwind it again.
If your seat belt is completely jammed,
pull slowly, but firmly, so that just over
3 cm unwinds. Allow it to return slightly
before attempting to unwind it again.
If there is still a problem, contact an approved dealer.
5
Note: an object placed on the passenger seat base may activate the warning
light in some cases.
Rear seat belt reminder (depending
on vehicle)
ß
the
warning light on the central display lights up accompanied by a
message on the instrument panel indicating the number of seat belts buckled for approximately 30 seconds each
time:
– the vehicle is started;
– a door is opened;
– a rear seat belt is fastened or unfastened.
Check that the rear passengers are
wearing seat belts and that the number
of seat belt shown as fastened corresponds to the number of rear bench
seat places occupied.
Adjusting the front seat belt
height
(depending on vehicle)
Press button 5 to adjust the seat belt
height so that shoulder strap 1 is worn
as shown previously:
– to lower the seat belt, press button 5
and lower the seat belt at the same
time;
– to raise the seat belt, press button 5
and raise the seat belt at the same
time.
Make sure that the seat belt is locked
in position correctly after you have adjusted it.
1.23
SEAT BELTS (3/3)
The following information applies to the vehicle’s front and rear seat belts.
– No modification may be made to the component parts of the originally
fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer.
– Do not use devices which allow any slack in the belts (e.g. clothes
pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the
event of an accident.
6
– Never wear the shoulder strap under your arm or behind your back.
– Never use the same belt for more than one person and never hold a baby or
child on your lap with your seat belt around them.
– The belt should never be twisted.
Unfastening
Press button 6 and the seat belt will be
rewound by the inertia reel. Guide the
belt.
Note: when driving, if a rear seat belt
is unbuckled, the message “Rear seat
belt unbuckled” appears on the instrument panel.
1.24
– Following an accident, have the seat belts checked and replaced if necessary.
Always replace your seat belts as soon as they show any signs of wear.
– Make sure that the buckle is inserted into the appropriate catch.
– Ensure that no objects are placed in the area around the seat belt catch as
they could prevent it from being properly secured.
– When repositioning the rear bench seat, make sure that the seat belt is correctly positioned so that it can be used properly.
– Make sure the seat belt catch is properly positioned (it should not be hidden
away, crushed or flattened by people or objects).
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4)
Depending on the vehicle, they are
composed of:
– seat belt inertia reel pretensioners;
– Have the entire restraint
system checked following
an accident.
– No operation whatsoever is permitted on any part of
the system (pretensioners, air
bags, computers, wiring) and the
system components must not
be reused on any other vehicle,
even if identical.
– lap belt pretensioners;
– chest-level load limiters;
– anti-submarining air bags;
– air bags for driver and front passenger.
These systems are designed to act independently or together when the vehicle is subjected to a frontal impact.
Depending on the severity of the
impact, the system can trigger:
– seat belt locking;
– the seat belt inertia reel pretensioner
(which engages to correct seat belt
slack);
– the low volume front air bag;
– the lap seat belt pretensioners to
hold the occupant in his seat;
– the large volume front air bag.
Pretensioners
– To avoid incorrect triggering of
the system which may cause
injury, only qualified personnel
from an approved dealer may
work on the pretensioner and air
bag system.
The pretensioners hold the seat belt
against the body, holding the occupant
more securely against the seat, thus increasing the seat belt’s efficiency.
– The electric trigger system may
only be tested by a specially
trained technician using special
equipment.
In the event of a severe frontal impact
and if the ignition is switched on, the
system may engage the following depending on the force of the impact:
– When the vehicle is scrapped,
contact an approved dealer for
disposal of the pretensioner and
air bag gas generators.
1
2
– seat belt inertia reel pretensioner 1
which instantly retracts the seat belt;
– the lap pretensioner 2 on the front
seats.
1.25
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4)
Load limiter
Above a certain severity of impact, this
mechanism is used to limit the force of
the belt against the body so that it is at
an acceptable level.
Anti-submarining air bag
Located on each of the front seats, it
deploys in order to prevent the occupant from sliding under the seat belt.
Air bags for driver and front
passenger
Fitted to the driver and passenger side.
Depending on the vehicle, the presence of this equipment is indicated
by the word “Airbag” on the steering
wheel, dashboard (air bag zone A) and
a symbol on the lower section of the
windscreen.
A
Each air bag system consists of:
– an air bag and gas generator fitted
on the steering wheel for the driver
and in the dashboard for the front
passenger;
– an electronic unit for system monitoring which controls the gas generator
electrical trigger system;
– remote sensors;
– a single warning light
instrument panel.
1.26
å
on the
The air bag system uses
pyrotechnic principles. This
explains why, when the air
bag inflates, it will generate heat, produce smoke (this does
not mean that a fire is about to start)
and make a noise upon detonation.
In a situation where an air bag is
required, it will inflate immediately
and this may cause some minor, superficial grazing to the skin or other
problems.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4)
Operation
This system is only operational when
the ignition is switched on.
In a severe frontal impact, the air bags
inflate rapidly, cushioning the impact
of the driver’s head and chest against
the steering wheel and the front passenger against the dashboard. The air
bags then deflate immediately so that
the passengers are not in any way hindered from leaving the vehicle.
Special feature of the front air
bag
After a violent impact, it has two deployment volumes and integrates a ventilation system:
– small volume air bag, this is the first
stage of operation;
– large volume air bag, the air bag
seams rip so that a larger volume of
gas is released into the bag (for the
most severe impacts).
1.27
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4)
All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when the air bag inflates.
Warnings concerning the driver’s air bag
– Do not modify the steering wheel or the steering wheel boss.
– Do not cover the steering wheel boss under any circumstances.
– Do not attach any objects (badge, logo, clock, telephone holder, etc.) to the steering wheel boss.
– The steering wheel must not be removed (except by qualified personnel from our Network).
– When driving, do not sit too close to the steering wheel. Sit with your arms slightly bent (see the information on “Adjusting
your driving position” in Section 1). This will allow sufficient space for the air bag to deploy correctly and be fully effective.
Warnings concerning the passenger air bag
– Do not attach or glue any objects (badge, logo, clock, telephone holder, etc.) to the dashboard on or near the air bag.
– Do not place anything between the dashboard and the passenger (pet, umbrella, walking stick, parcels, etc.).
– The passenger must not put his or her feet on the dashboard or seat as there is a risk that serious injuries may occur. In
general, parts of the body should be kept away from the dashboard (knees, hands, head, etc.).
– The devices in addition to the front passenger seat belt should be reactivated as soon as a child seat is removed, to ensure
the protection of the passenger in the event of an impact.
A REAR-FACING CHILD SEAT MUST NOT BE FITTED TO THE FRONT PASSENGER SEAT UNLESS
THE ADDITIONAL RESTRAINT SYSTEMS, I.E. THE PASSENGER AIR BAG, ARE DEACTIVATED.
(refer to the information on “Child safety: deactivating/activating the front passenger air bag” in Section 1)
Warnings concerning the anti-submarining air bag
Do not let a child under the age of 12 sit in this seat. When triggered, the anti-submarining air bag may project objects left on
the seat base with a great deal of force.
Risk of serious injury.
1.28
METHODS OF RESTRAINT IN ADDITION TO THE REAR SEAT BELTS
Force limiter
Above a certain severity of impact, this
mechanism is used to limit the force of
the belt against the body so that it is at
an acceptable level.
– Have the entire restraint
system checked following
an accident.
– No operation whatsoever
is permitted on any part of the
system (air bags, electronic control units, wiring) and the system
components must not be reused
on any other vehicle, even if identical.
– Only qualified personnel from
our Network may work on the air
bags; otherwise the system may
trigger accidentally and cause
injury.
1.29
SIDE PROTECTION DEVICES
Side air bags
These air bags are fitted to the front
seats and are activated at the sides of
the seats (door side) to protect the occupants in the event of a severe side
impact.
Curtain air bags
These are air bags fitted along the sides
of the vehicle in the ceiling which trigger
along the front and rear side windows
to protect the passengers in case of a
severe side impact.
Warnings concerning the side air bag
– Fitting seat covers: seats equipped with an air bag require covers
specifically designed for your vehicle. Contact an approved Dealer to find
out if these covers are available. The use of any covers other than those
designed for your vehicle (and including those designed for another vehicle)
may affect the operation of the air bags and reduce your protection.
– Do not place any accessories, objects or even pets between the seatback, the
door and the internal fittings. Do not cover the seatback with any items such as
clothes or accessories. This may prevent the air bag from operating correctly
or cause injury when the air bag is deployed.
– No work or modification whatsoever may be carried out on the seat or internal
fittings, except by qualified personnel from an approved dealer.
– The area between the rear bench seatback and the trim is the area of air bag
operation: no objects must be placed here.
1.30
ADDITIONAL METHODS OF RESTRAINT
All of the warnings below are given so that the air bag is not obstructed in any
way when it is inflated and also to prevent the risk of serious injuries caused
by items which may be dislodged when the air bag inflates.
The air bag is designed to complement the action of the seat belt. Both
the air bags and seat belts are integral parts of the same protection
system. It is therefore essential to wear seat belts at all times. If seat belts
are not worn, the occupants are exposed to the risk of serious injury in
the event of an accident. It may also increase the risk of minor superficial injuries
occurring when the air bag is deployed, although such minor injuries are always
possible with air bags.
If the vehicle should overturn or suffer a rear impact, however severe, the pretensioners and air bags are not always triggered. Shocks to the underbody of the
vehicle, e.g. from pavements, potholes or stones, can all trigger these systems.
– No work or modification whatsoever may be carried out on any part of the air
bag system (air bags, pretensioners, computer, wiring harness, etc.), except
by qualified personnel from an approved dealer.
– To ensure that the system is in good working order and to avoid accidental triggering of the system which may cause injury, only qualified Network personnel
may work on the air bag system.
– As a safety precaution, have the air bag system checked if your vehicle has
been involved in an accident, or is stolen or broken into.
– When selling or lending the vehicle, inform the user of these points and hand
over this driver’s handbook with the vehicle.
– When scrapping your vehicle, contact your approved dealer for disposal of the
gas generator(s).
1
Operating faults
Warning light 1 will light up on the instrument panel when the ignition is
switched on and then go out after a few
seconds.
If it does not come on when the ignition
is switched on, or if it comes on when
the engine is running, there is a fault
with the system (air bags, pretensioners, etc.) in the front and/or rear seats.
Contact your approved dealer as soon
as possible. Your protection will be reduced until this fault is rectified.
1.31
CHILD SAFETY: General information (1/2)
Carrying children
Children, and adults, must be correctly
seated and strapped in for all journeys.
The children being carried in your vehicle are your responsibility.
A child is not a miniature adult. Children
are at risk of specific injuries as their
muscles and bones have not yet finished growing. The seat belt alone
would not provide suitable protection.
Use an approved child seat and ensure
you use it correctly.
To prevent the doors being
opened, use the “Child
safety” device (refer to the
information on “Opening
and closing the doors” in Section 1).
1.32
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-sufficient alone on your vehicle, even for
a short time.
A collision at 30 mph (50
km/h) is the same as falling a distance of 10 metres.
Transporting a child without
a restraint is the equivalent of allowing him or her to play on a fourthfloor balcony without railings.
Never travel with a child held in your
arms. In the event of an accident,
you will not be able to keep hold of
the child, even if you yourself are
wearing a seat belt.
If your vehicle has been involved in
a road accident, replace the child
seat and have the seat belts and
ISOFIX anchorage points checked.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or by locking the
doors.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
CHILD SAFETY: General information (2/2)
Using a child seat
The level of protection offered by the
child seat depends on its ability to restrain your child and on its installation.
Incorrect installation compromises the
protection it offers the child in the event
of harsh braking or an impact.
Before purchasing a child seat, check
that it complies with the regulations for
the country you are in and that it can
be fitted in your vehicle. Consult an approved dealer to find out which seats
are recommended for your vehicle.
Before fitting a child seat, read the
manual and respect its instructions. If
you experience any difficulties during
installation, contact the manufacturer
of the equipment. Keep the instructions
with the seat.
Set a good example by always fastening your seat belt and teaching
your child:
– to strap themselves in correctly;
– to always get in and out of the car
at the kerb, away from busy traffic.
Do not use a second-hand child
seat or one without an instruction
manual.
Check that there are no objects in
the vicinity of the child seat which
could impede its operation.
Never leave a child unattended in the vehicle.
Check that your child is
always strapped in and that
the belt or safety harness used is
correctly set and adjusted. Avoid
wearing bulky clothing which could
cause the belts to slacken.
Never let your child put their head or
arms out of the window.
Check that the child is in the correct
position for the entire journey, especially if asleep.
1.33
CHILD SAFETY: Choosing a child seat
Rear-facing child seats
A baby’s head is, proportionally, heavier
than that of an adult and its neck is very
fragile. Transport the child in this position as long as possible (until the age of
2 at the very least). It supports both the
head and the neck.
Choose a bucket type seat for best side
protection and change it as soon as the
child’s head is higher than the shell.
1.34
Forward-facing child seats
The child’s head and abdomen need to
be protected as a priority. A forward-facing child seat which is firmly attached to
the vehicle will reduce the risk of impact
to the head. Ensure your child travels in
a forward-facing seat with a harness or
buckle for as long as their size permits.
Choose a bucket type seat for optimum
side protection.w
Booster cushions
From 15 kg or 4 years, the child can
travel using a booster seat, which will
enable the seat belt to be adapted to
suit his size and shape. The booster
seat cushion must be fitted with guides
to position the seat belt on the child’s
thighs rather than the stomach. It is
recommended that you use a seatback which can be adjusted in terms
of height to position the seat belt in the
centre of the shoulder. It must never
rest on the neck or on the arm.
Choose a bucket type seat for optimum
side protection.
CHILD SAFETY: choosing a child seat mounting (1/2)
There are two ways of attaching child
seats: via the seat belt or using the
ISOFIX system.
Attachment via the seat belt
The seat belt must be adjusted to
ensure that it is effective in the event of
harsh braking or an impact.
Ensure that the strap paths indicated
by the child seat manufacturer are respected.
Always check that the seat belt is correctly fastened by pulling it up, then
pulling it out fully whilst pressing on the
child seat.
Check that the seat is correctly held by
moving it from side to side and back
to front: the seat should remain firmly
fixed.
Check that the child seat has not been
installed at an angle and that it is not
resting against a window.
Do not use the child seat
if it may unfasten the seat
belt restraining it: the base
of the seat must not rest on
the buckle and/or catch of the seat
belt.
The seat belt must never
be twisted or the tension
relieved. Never pass the
shoulder strap under the
arm or behind the back.
Check that the seat belt has not
been damaged by sharp edges.
If the seat belt does not operate normally, it will not protect the child.
Consult an approved dealer. Do not
use this seat until the seat belt has
been repaired.
No modifications may be
made to the component
parts of the restraint system
(seat belts, ISOFIX, seats
and their mountings) originally fitted.
Attachment using the ISOFIX
system
Authorised ISOFIX child seats are approved in accordance with regulation
ECE-R44 in one of the three following
scenarios:
– ISOFIX universal 3-point forwardfacing seat
– ISOFIX semi-universal 2-point seat
– specific
For the latter two, check that your child
seat can be installed by consulting the
list of compatible vehicles.
Attach the child seat with the ISOFIX
locks, if these are provided. The ISOFIX
system allows quick, easy, safe fitting.
The ISOFIX system consists of 2 rings
and, in some cases, a third ring.
Before using an ISOFIX
child seat that you purchased for another vehicle,
check that its installation is
authorised. Consult the list of vehicles which can be fitted with the
seat from the equipment manufacturer.
1.35
CHILD SAFETY: choosing a child seat mounting (2/2)
The ISOFIX anchorage
points have been exclusively designed for child
seats with the ISOFIX
system. Never fit a different type of
child seat, seat belt or other objects
to these anchorage points.
1
2
The two rings 1 are located between
the seatback and the seat base of the
seat and are identified by a marking.
To ensure your child seat can be easily
fitted and locked on the rings 1, use
access guides 2 on the child seat.
3
The third ring is used to attach the
upper strap on some child seats.
Pass the belt between the seatback
and the rear parcel shelf (to remove
the parcel shelf: refer to Section 3
“Parcel shelf”). Fix the hook on one of
the rings 3 located in the luggage compartment (visible for three- and fivedoor versions; under the carpet and
indicated with a marking on the Sport
tourer version).
Pull the belt so that the back of the child
seat comes into contact with the vehicle
seatback.
1.36
Check that nothing is obstructing
the anchorage points.
If your vehicle has been involved in
a road accident, have the ISOFIX
anchorage points checked and replace your child seat.
CHILD SAFETY: fitting a child seat (1/11)
Some seats are not suitable for fitting
child seats. The diagram on the following page shows you how to attach a
child seat.
The types of child seats indicated may
not be available. Before using a different child seat, check with the manufacturer that it can be fitted.
Fit the child seat in a rear
seat wherever possible.
Check that when installing
the child seat in the vehicle
it is not at risk of coming loose from
its base.
If you have to remove the headrest,
check that it is correctly stored so
that it does not come loose under
harsh braking or impact.
Always attach the child seat to the
vehicle even if it is not in use so that
it does not come loose under harsh
braking or impact.
In the front seat
The laws concerning children travelling in the front passenger seat differ in
every country. Consult the legislation in
force and follow the indications on the
diagram on the following page.
Before fitting a child seat in this seat (if
authorised):
– lower the seat belt as far as possible;
– move the seat as far back as possible;
– gently tilt the seatback away from
vertical (approximately 25°);
– on equipped vehicles, raise the seat
base as far as possible.
Do not change these settings after the
child seat is installed.
RISK OF DEATH OR
SERIOUS INJURY: before
fitting a rear-facing child
seat in this position, check
that the air bag has been deactivated (refer to the information on
“Child safety: deactivating/activating the front passenger air bag” in
Section 1).
In the rear side seat
A carrycot can be installed across the
vehicle and will take up at least two
seats. Position the child with his or her
feet nearest the door.
Push the vehicle seat fully forwards
to install a rear-facing child seat, then
push it back as far as possible without allowing it to make contact with the
child seat.
For the safety of the child in the forward-facing seat, do not move the seat
in front back past the middle of the
runner, do not tilt the seatback too far
(maximum of 25°) and raise the seat as
much as possible.
Check that the forward-facing child seat
is resting against the back of the vehicle seat and that the headrest of the vehicle is not obstructing its use.
Ensure that the child seat
or the child’s feet do not
prevent the front seat from
locking correctly. Refer to
the information on the “Front seat”
in Section 1.
1.37
CHILD SAFETY: fitting a child seat (2/11)
The table below summarises the information already shown in the diagram on the following pages, to ensure the applicable regulations are respected.
Type of child seat
three and five door
versions (five seats)
Weight of
the child
Carrycot fitted across the
vehicle
< 10 kg
Group 0
Seat size
ISOFIX
Passenger front
seat (1) (2)
Rear side seats
Rear centre
seat
F-G
X
U - IL (3)
X
Rear-facing shell seat
Group 0 or 0+
< 13 kg
E
U
U - IL (4)
X
Rear-facing seat
Group 0+ and 1
< 13 kg and
9 to 18 kg
D
U
U - IL (4)
X
C
U
U (4)
X
Forward-facing seat
Group 1
9 to 18 kg
A, B, B1
X
U - IUF - IL (5)
X
Booster seat
Group 2 and 3
15 to 25 kg and
22 to 36 kg
X
U (5)
X
(1) RISK OF DEATH OR SERIOUS INJURY: before installing a rear-facing child seat on the front passenger seat,
check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the front
passenger air bag” at the end of the paragraph).
1.38
CHILD SAFETY: fitting a child seat (3/11)
X = Seat not suitable for fitting child seats.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be
attached using the ISOFIX system; check that it can be fitted.
(2) Only a rear-facing child seat can be fitted in this seat: raise the seat to the maximum and position it as far back as possible,
tilting the seatback slightly (approximately 25°).
(3) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(4) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(5) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the
headrest, or remove it if necessary. Do not push the front seat more than halfway back on its runners and do not recline the
seatback more than 25°.
1.39
CHILD SAFETY: fitting a child seat (4/11)
Child seat attached using the ISOFIX
mounting
ü
±
Seat which allows an ISOFIX
child seat to be fitted.
The rear seats are fitted with
an anchorage point which allows a
forward-facing ISOFIX child seat with
universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible.
Visual installation of three
and five door versions (five
seats)
³
−
Check the status of the air bag
before fitting a child seat or allowing a
passenger to use the seat.
Seat which only allows a rearfacing seat with “Universal” approval
to be attached with a seat belt.
²
seats.
Seat not suitable for fitting child
Child seat attached using the belt
¬
Seat which allows a child seat
with “Universal” approval to be attached
by a seat belt.
RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child
seat in the front passenger seat, check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the
front passenger air bag” at the end of the paragraph).
1.40
The size of the ISOFIX child seat is indicated by a letter:
– A, B and B1: for forward-facing seats
in group 1 (9 to 18 kg);
– C: rear-facing seats in group 1 (9 to
18 kg);
– D and E: shell seat or rear-facing
seats in group 0 or 0+ (less than
13 kg);
– F and G: cots in group 0 (less than
10 kg).
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
CHILD SAFETY: fitting a child seat (5/11)
Child seat attached using the ISOFIX
mounting
ü
±
Seat which allows an ISOFIX
child seat to be fitted.
The rear seats are fitted with
an anchorage point which allows a
forward-facing ISOFIX child seat with
universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible.
Visual installation of five
door versions (four seats)
³
−
Check the status of the air bag
before fitting a child seat or allowing a
passenger to use the seat.
Seat which only allows a rearfacing seat with “Universal” approval
to be attached with a seat belt.
²
seats.
Seat not suitable for fitting child
Child seat attached using the belt
¬
Seat which allows a child seat
with “Universal” approval to be attached
by a seat belt.
RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child
seat in the front passenger seat, check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the
front passenger air bag” at the end of the paragraph).
The size of the ISOFIX child seat is indicated by a letter:
– A, B and B1: for forward-facing seats
in group 1 (9 to 18 kg);
– C: rear-facing seats in group 1 (9 to
18 kg);
– D and E: shell seat or rear-facing
seats in group 0 or 0+ (less than
13 kg);
– F and G: cots in group 0 (less than
10 kg).
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
1.41
CHILD SAFETY: fitting a child seat (6/11)
The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
Type of child seat
five door version
(four seats)
Weight of
the child
Carrycot fitted across the
vehicle
< 10 kg
Group 0
Seat size
ISOFIX
Passenger front
seat (1) (2)
Rear side seats
F-G
X
U - IL (3)
Rear-facing shell seat
Group 0 or 0+
< 13 kg
E
U
U - IL (4)
Rear-facing seat
Group 0+ and 1
< 13 kg and
9 to 18 kg
D
U
U - IL (4)
C
U
U (4)
Forward-facing seat
Group 1
9 to 18 kg
A, B, B1
X
U - IUF - IL (5)
Booster seat
Group 2 and 3
15 to 25 kg and
22 to 36 kg
X
U (5)
(1) RISK OF DEATH OR SERIOUS INJURY: before installing a rear-facing child seat on the front passenger seat,
check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the front
passenger air bag” at the end of the paragraph).
1.42
CHILD SAFETY: fitting a child seat (7/11)
X = Seat not suitable for fitting child seats.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be
attached using the ISOFIX system; check that it can be fitted.
(2) Only a rear-facing child seat can be fitted in this seat: raise the seat to the maximum and position it as far back as possible,
tilting the seatback slightly (approximately 25°).
(3) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(4) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(5) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the
headrest, or remove it if necessary. Do not push the front seat more than halfway back on its runners and do not recline the
seatback more than 25°.
1.43
CHILD SAFETY: fitting a child seat (8/11)
Child seat attached using the ISOFIX
mounting
ü
±
Seat which allows an ISOFIX
child seat to be fitted.
The rear seats are fitted with
an anchorage point which allows a
forward-facing ISOFIX child seat with
universal approval to be fitted. The anchorage points are located under the
luggage compartment carpet and are
indicated by a marking.
Visual installation of the
estate version (five seats)
³
−
Check the status of the air bag
before fitting a child seat or allowing a
passenger to use the seat.
Seat which only allows a rearfacing seat with “Universal” approval
to be attached with a seat belt.
²
seats.
Seat not suitable for fitting child
Child seat attached using the belt
¬
Seat which allows a child seat
with “Universal” approval to be attached
by a seat belt.
RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child
seat in the front passenger seat, check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the
front passenger air bag” at the end of the paragraph).
1.44
The size of the ISOFIX child seat is indicated by a letter:
– A, B and B1: for forward-facing seats
in group 1 (9 to 18 kg);
– C: rear-facing seats in group 1 (9 to
18 kg);
– D and E: shell seat or rear-facing
seats in group 0 or 0+ (less than
13 kg);
– F and G: cots in group 0 (less than
10 kg).
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
CHILD SAFETY: fitting a child seat (9/11)
The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
Type of child seat
estate version (five seats)
Weight of
the child
Carrycot fitted across the vehicle
< 10 kg
Group 0
Seat size
ISOFIX
Front passenger
seat (1) (5)
Rear side seats
Rear centre
seat
F-G
X
U - IL (2)
X
Shell seat/rear-facing seat
Group 0, or 0+ and 1
< 13 kg and 9 to
18 kg
E, D, C
U
U - IL (3)
X
Forward-facing seat
Group 1
9 to 18 kg
A, B, B1
X
U - IUF - IL (4)
X
Booster seat
Group 2 and 3
15 to 25 kg and 22
to 36 kg
X
U (4)
X
X = Seat not suitable for fitting child seats.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be
attached using the ISOFIX system; check that it can be fitted.
(1) Only a rear-facing child seat can be fitted in this seat: raise the seat to the maximum and position it as far back as possible,
tilting the seatback slightly (approximately 25°).
(2) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(3) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(4) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the
headrest, or remove it if necessary. Do not push the front seat more than halfway back on its runners and do not recline the
seatback more than 25°.
(5) RISK OF DEATH OR SERIOUS INJURY: before installing a rear-facing child seat on the front passenger seat,
check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the front
passenger air bag” at the end of the section).
1.45
CHILD SAFETY: fitting a child seat (10/11)
Child seat attached using the ISOFIX
mounting
ü
±
Seat which allows an ISOFIX
child seat to be fitted.
The rear seats are fitted with
an anchorage point which allows a
forward-facing ISOFIX child seat with
universal approval to be fitted. The anchorage points are located under the
luggage compartment carpet and are
indicated by a marking.
Visual installation of the
estate version (four seats)
³
−
Check the status of the air bag
before fitting a child seat or allowing a
passenger to use the seat.
Seat which only allows a rearfacing seat with “Universal” approval
to be attached with a seat belt.
²
seats.
Seat not suitable for fitting child
Child seat attached using the belt
¬
Seat which allows a child seat
with “Universal” approval to be attached
by a seat belt.
RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child
seat in the front passenger seat, check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the
front passenger air bag” at the end of the paragraph).
1.46
The size of the ISOFIX child seat is indicated by a letter:
– A, B and B1: for forward-facing seats
in group 1 (9 to 18 kg);
– C: rear-facing seats in group 1 (9 to
18 kg);
– D and E: shell seat or rear-facing
seats in group 0 or 0+ (less than
13 kg);
– F and G: cots in group 0 (less than
10 kg).
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
CHILD SAFETY: fitting a child seat (11/11)
The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
Type of child seat
estate version (four seats)
Weight of
the child
Carrycot fitted across the vehicle
< 10 kg
Group 0
Seat size
ISOFIX
Front passenger
seat (1) (5)
Rear side seats
F-G
X
U - IL (2)
Shell seat/rear-facing seat
Group 0, or 0+ and 1
< 13 kg and 9 to
18 kg
E, D, C
U
U - IL (3)
Forward-facing seat
Group 1
9 to 18 kg
A, B, B1
X
U - IUF - IL (4)
Booster seat
Group 2 and 3
15 to 25 kg and 22
to 36 kg
X
U (4)
X = Seat not suitable for fitting child seats.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be
attached using the ISOFIX system; check that it can be fitted.
(1) Only a rear-facing child seat can be fitted in this seat: raise the seat to the maximum and position it as far back as possible,
tilting the seatback slightly (approximately 25°).
(2) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(3) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(4) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the
headrest, or remove it if necessary. Do not push the front seat more than halfway back on its runners and do not recline the
seatback more than 25°.
(5) RISK OF DEATH OR SERIOUS INJURY: before installing a rear-facing child seat on the front passenger seat,
check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the front
passenger air bag” at the end of the section).
1.47
CHILD SAFETY: deactivating/activating the front passenger air bag (1/3)
1
2
Deactivating the front
passenger airbags
To deactivate the airbags : when the
vehicle is stationary, push and turn
lock 1 to the OFF position.
You must deactivate certain devices
in addition to the front passenger seat
belt before fitting a child seat in the front
passenger seat.
With the ignition on, you must check
(on equipped vehicles)
¹
is lit
that the warning light 2
on the central display and, depending on the vehicle, that the message
“Passenger airbag off” is displayed.
This light remains permanently lit to
let you know that you can fit a child
seat.
The passenger airbag must
only be deactivated or activated when the vehicle is
stationary.
If it is interfered with when the vehicle is being driven, indicator lights
å
and © will come on.
Switch the ignition off then on again
to reset the airbag in accordance
with the lock position.
1.48
CHILD SAFETY: deactivating/activating the front passenger air bag (2/3)
B
C
A
3
DANGER
The markings on the dashboard and
labels B or C at A on each side of the
passenger sun visor 3 (example: label
shown above) remind you of these instructions.
Since front passenger
airbag triggering and the
position of a rear-facing
child seat are incompatible, NEVER
use a restraining device for rearfacing children on a seat with an
ACTIVATED AIRBAG in front of it.
This could lead to the DEATH of the
CHILD, or SERIOUS INJURY.
1.49
CHILD SAFETY: deactivating/activating the front passenger air bag (3/3)
DANGER
1
Since front passenger
airbag triggering and the
position of a rear-facing
child seat are incompatible, NEVER
use a restraining device for rearfacing children on a seat with an
ACTIVATED AIRBAG in front of it.
This could lead to the DEATH of the
CHILD, or SERIOUS INJURY.
4
Activating the front
passenger airbags
Operating faults
You should reactivate the airbags as
soon as you remove the child seat from
the front passenger seat to ensure the
protection of the front passenger in the
event of an impact.
It is prohibited to fit a rear-facing child
seat to the front passenger seat if the
front passenger airbags activation/
deactivation system shows a fault.
Allowing any other passenger to sit in
that seat is not recommended.
To reactivate the airbags : when the
vehicle is stationary, push and turn
lock 1 to position ON.
If warning lights
lit at the same time.
With the ignition on, it is essential to
Contact your approved dealer as soon
as possible.
›
is lit
check that warning light 4
on the central display, and that it goes
out after a few seconds.
1.50
› ¹
and
are
The passenger airbag must
only be deactivated or activated when the vehicle is
stationary.
If it is interfered with when the vehicle is being driven, indicator lights
å
and © will come on.
Switch the ignition off then on again
to reset the airbag in accordance
with the lock position.
STEERING WHEEL/POWER-ASSISTED STEERING
Power-assisted steering
Variable power-assisted steering
The variable power-assisted steering
system is equipped with an electronic
control system which alters the level of
assistance to suit the vehicle speed.
1
Height and reach adjustment
Pull lever 1 and move the steering
wheel to the required position.
Then, push the lever back fully, beyond
the point of resistance to lock the steering wheel.
Make sure that the steering wheel is
correctly locked.
For safety reasons, only
adjust the steering wheel
when the vehicle is stationary.
Operating faults
The steering may become stiff when
driving or when the steering wheel is
turned repeatedly. This is due to the
power assistance overheating. In this
case, it must be allowed to cool down.
Steering is made easier during parking
manoeuvres (for added comfort) whilst
the force needed to steer increases
progressively as the speed rises (for
enhanced safety at high speeds).
Never leave the steering wheel at
full lock while stationary.
With the engine switched off, or if
there is a system fault, it is still possible to turn the steering wheel. The
force required will be greater.
Never switch off the ignition when travelling downhill, and avoid doing so in
normal driving (assistance
is not provided).
1.51
DRIVING POSITION: LEFT-HAND DRIVE (1/2)
1
25
2
3
24 23
4
22
5
6
7
8
9
21 20
15
19
16
17
18
1.52
10
14
13
12
11
DRIVING POSITION: LEFT-HAND DRIVE (2/2)
The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
1 Side air vent.
2 Side window demister outlet.
3 Stalk for:
– direction indicator lights;
– exterior lights;
– front fog lights;
– rear fog light.
4 Instrument panel.
5 Driver’s air bag and horn location.
6 – Steering column stalk for windscreen and rear screen wash/
wipe;
– On-board computer information
read-out control and vehicle settings customisation menu.
7 Centre air vents.
8 – Display of time, temperature,
radio information, navigation
system information, etc.
– Driver and front passenger seat
belt reminder warning light and
front passenger airbag activated/
deactivated warning lights.
9 Location for passenger air bag.
10 Side window demister outlet.
11 Side air vent.
12 Glove box.
13 Heating and ventilation controls.
14 Location for radio, navigation
system, etc.
19 Gear lever.
20 Engine start/stop button
RENAULT card reader.
and
21 Central door locking/unlocking controls and hazard warning lights
switch.
22 Cruise control/speed limiter controls.
23 Control for adjusting steering wheel
height and reach.
24 Bonnet release control.
25 Controls for:
– headlight beam height remote adjustment;
15 Accessories socket.
– lighting rheostat for control instruments;
16 Control for some multimedia equipment.
– activation/deactivation of the traction control;
17 Cruise control/speed limiter main
control.
– activation/deactivation of the
function Stop and Start.
18 Electronic parking brake or manual
parking brake control.
1.53
DRIVING POSITION: RIGHT-HAND DRIVE (1/2)
1
2
25
3
24
4
23
19
18
1.54
6
7
8
9
10 11
22
21
20
17
5
16 15 14
17
13
12
DRIVING POSITION: RIGHT-HAND DRIVE (2/2)
The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
1 Side air vent.
2 Side window demister outlet.
3 Location for passenger air bag.
4 – Display (depending on the vehicle) of time, temperature, radio
information, navigation system information, etc.
– Driver and front passenger seat
belt unfastened and passenger
airbag deactivated warning lights.
5 Centre air vents.
6 Stalk for:
– direction indicator lights;
– exterior lights;
– front fog lights;
– rear fog light.
7 Location for driver’s air bag and
horn.
8 Instrument panel.
9 – Steering column stalk for windscreen and rear screen wash/wipe;
– On-board computer information
read-out control and vehicle settings customisation menu.
10 Side window demister outlet.
11 Side air vent.
12 Controls for:
15 Central door locking/unlocking
controls and hazard warning lights
switch.
16 Air-conditioning control.
17 Control for some multimedia equipment.
18 Cruise control/speed limiter main
control.
– headlight beam height remote adjustment;
19 Electronic parking brake or manual
parking brake control.
– lighting rheostat for control instruments;
20 Gear lever.
21 Accessories socket.
– activation/deactivation of the traction control;
22 Engine start/stop control and card
reader RENAULT.
– activation/deactivation of the
function Stop and Start.
23 Location for radio, navigation
system, etc.
13 Cruise control/speed limiter controls.
24 Glove box.
14 Control for adjusting steering wheel
height and reach.
25 Bonnet release control.
1.55
WARNING LIGHTS (1/4)
The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.
A
1
The instrument panel A lights up
when the ignition is switched on. You
can adjust the brightness of the instrument panel by turning control knob 1.
In some cases, the appearance of a
warning light is accompanied by a message.
The warning light © means
you should drive very carefully to
an authorised dealer as soon as
possible. If you fail to follow this recommendation, you risk damaging
your vehicle.
1.56
u
á
k
g
f
Side light tell-tale light
Main beam headlight tell-tale
light
Dipped beam headlight telltale light
Front fog light tell-tale light
Rear fog light tell-tale light
Warning light ® requires you to stop immediately, for your own safety,
as soon as traffic conditions allow.
Switch off the engine and do not restart it. Contact an approved Dealer.
Automatic main beam headlight indicator light
Please refer to the information
on “External signals and lights” in
Section 1.
c
b
}
Left-hand direction indicator
tell-tale light
Right-hand direction indicator tell-tale light
Handbrake “on” or electronic parking brake warning light
Refer to the information on the
“Handbrake” or “Electronic parking
brake” in Section 2.
If no lights or sounds are apparent, this indicates a fault
in the instrument panel. This
indicates that it is essential
to stop immediately (as soon as traffic conditions allow). Ensure that the
vehicle is correctly immobilised and
contact an approved Dealer.
WARNING LIGHTS (2/4)
The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.
Warning light
© This lights up when the ignition
A
is switched on and goes out as soon as
the engine is started. It can light up in
conjunction with other indicator lights
and/or messages on the instrument
panel.
It means you should drive very carefully to an authorised dealer as soon
as possible. If you fail to follow this recommendation, you risk damaging your
vehicle.
Air bag warning light
This comes on when the ignition is switched on and goes out after a
few seconds.
If it does not light up when the ignition
is switched on, or comes on when the
engine is running, there is a fault in the
system.
Contact your approved Dealer as soon
as possible.
å
Speed limiter and cruise
control warning light
See the information on the “Speed limiter” and “Cruise control” in Section 2.
Î
Fuel economy indicator light
This lights up to advise you to change
to a higher gear (up arrow) or lower
gear (down arrow).
\[
É
Preheating warning light
(diesel version)
This should come on when the ignition is switched on. It indicates that the
heater plugs are in operation. This goes
out as soon as the engine starts.
Anti-lock braking warning
light
This lights up when the ignition is
switched on and goes out after a few
seconds.
x
If it does not go out after the ignition is
switched on, or lights up when driving,
there is a fault with the ABS. Braking
will then be as normal, without the ABS.
Contact an approved Dealer as soon as
possible.
Toxic Fume Filter System
Warning Light
This lights up when the ignition is
switched on and goes out when the
engine is started.
– If it lights up continuously, consult
your approved Dealer as soon as
possible;
– if it flashes, reduce the engine speed
until the light stops flashing. Contact
your approved Dealer as soon as
possible.
Refer to the information on
“Antipollution, fuel economy and driving” in Section 2.
Ä
1.57
WARNING LIGHTS (3/4)
The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.
À
A
If it comes on when you are
driving accompanied by the ®
warning light and a beep, it is essential to stop and switch off the ignition.
Check the oil level (refer to the information on “Engine oil level” in Section 4).
If the level is normal, the light has come
on for another reason: contact an authorised dealer.
Brake circuit fault warning
light
If it comes on during braking and is accompanied by the ® warning light
and a beep, it indicates that the fluid
level in the circuit is low or that there is
a braking system fault. Stop as soon as
traffic conditions allow and contact an
approved Dealer.
D
STOP light
® This lights up when the ignition
is switched on and goes out as soon as
the engine is started. It comes on with
other warning lights and/or messages,
and is accompanied by a beep.
It requires you to stop immediately, for
your own safety, as soon as traffic conditions allow. Switch off the engine and
do not restart it.
Contact an approved Dealer.
1.58
Oil pressure warning light
Ô
Engine coolant temperature
warning light
This lights up when the ignition is
switched on and goes out when the
engine is started. If it comes on when
you are driving accompanied by the
® warning light and a beep, it is
essential to stop and switch off the ignition.
Check the coolant level (refer to the information on “Levels” in Section 4). If
the level is correct, the light has come
on for another reason; consult an approved dealer.
Battery charge warning light
If it comes on together with the
® warning light and a beep, it indicates that the electrical circuit is overcharged or undercharged.
Ú
WARNING LIGHTS (4/4)
The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.
Front seat belt reminder
warning light
This lights up on the central display
when starting the engine then, if the
driver’s or front passenger’s seat belt
(if this seat is occupied) is not fastened
and the vehicle has reached approximately 12 mph (20 km/h), it flashes and
a bleep sounds for around 120 seconds.
Note: an object placed on the passenger seat base may activate the warning
light in some cases.
ß
Rear seat belt reminder (depending
on vehicle)
ß
Warning light
lights up on the
central display, accompanied by a message on the instrument panel, indicating the number of seat belts buckled for
approximately 30 seconds each:
– the vehicle is started;
– a door is opened;
– a rear seat belt is fastened or unfastened.
Check that the rear passengers are
wearing seat belts and that the number
of seat belt shown as fastened corresponds to the number of rear bench
seat places occupied.
ð
Heated seats operating indicator
This indicates that one of the heated
seats is in operation.
Low fuel level warning light
This comes on when the ignition is switched on and goes out after a
few seconds. If it comes on when driving accompanied by a beep, fill up with
fuel as soon as possible. There is only
approximately 30 miles (50 km) worth
of fuel left after the warning light first
comes on.
L
Ü
Not used
Lane departure
warning light
Driving correction device
warning light
Refer to information on “Driver correction devices and aids” in Section 2.
system
Please refer to the information on “Lane
departure warning” in Section 2.
1.59
DISPLAYS AND INDICATORS (1/2)
1
3
2
a
6
Rev counter 1 (rpm × 1 000)
5
4
Coolant temperature indicator 4
In normal use, indicator 4 should be
before area a. Under severe conditions, the needle may enter this area.
This is not serious unless the ®
warning light comes on, accompanied
by a message on the instrument panel
and a beep.
Engine oil level low warning
Trip computer and warning system
When the engine is started, display 3
alerts the driver when the oil level is
at its minimum. Refer to Section 4:
“Engine oil level”.
Refer to the information on the “Trip
computer and warning system” in
Section 1.
The first time the alert appears, it can
be cleared by pressing one of the buttons on the end of stalk 2.
Subsequent warnings will disappear
automatically after 30 seconds.
1.60
Fuel level gauge 5
If the minimum level is reached, indicator light 6 comes on and a beep
sounds. Fill up as soon as possible.
There is only approximately 30 miles
(50 km) worth of fuel left after the warning light first comes on.
DISPLAYS AND INDICATORS (2/2)
2
7
9
2
10
8
Speedometer 7 (mph or km/h)
Overspeed buzzer
Depending on the vehicle and country,
a buzzer sounds for approximately 10
seconds every 40 seconds, as long as
the vehicle is travelling in excess of 72
mph (120 km/h).
Instrument panel in miles
(option to switch to km/h)
– With the ignition off, press one of the
buttons 9 or 10 at the end of stalk 2
and start button 8;
– the speedometer unit indicator
flashes for approximately ten seconds, then the new unit is displayed:
release button 9 or 10 when the unit
stops flashing.
To return to the previous mode, repeat
the same operation.
Note: once the battery is switched off,
the trip computer and warning system
automatically returns to the original unit
of measurement.
1.61
TRIP COMPUTER: general information (1/2)
c) mileage before service;
d) tyre pressure monitor;
1
2
3
Trip computer and warning
system 1
Display selection keys 2
and 3
Depending on the vehicle, this includes
the following functions:
Scroll through the following information upwards (button 2) or downwards
(button 3) by pressing briefly and successively (the display depends on the
vehicle equipment and country).
– distance travelled;
– journey parameters;
– information messages;
– operating fault messages (connected to the warning light ©);
– warning messages (connected to the
® warning light);
– vehicle settings customisation menu.
All these functions are described on the
following pages.
1.62
a) total mileage and trip mileage recorder;
b) journey parameters:
– fuel used;
– average fuel consumption;
– current fuel consumption;
– estimated range;
– distance travelled;
– average speed;
e) vehicle settings customisation menu;
f) trip log, operating faults and information message readout.
TRIP COMPUTER: general information (2/2)
2
3
Trip mileage resetting
With “trip mileage recorder” selected on
the display, press button 2 or 3 until the
mileage recorder resets to zero.
Resetting the journey
parameters (reset button)
Interpreting some of the
values displayed after
resetting
The values showing average fuel consumption, range and average speed
will become more stable and reliable
the further you travel after pressing the
reset button.
Automatic resetting of the
journey parameters
Resetting occurs automatically when
the maximum value of any of the parameters is exceeded.
For the first few miles after pressing
the reset key you will notice that the
range increases as you travel. This
range takes into account the average
fuel consumption since the last time the
reset button was pressed. Therefore,
the average fuel consumption may decrease when:
– the vehicle stops accelerating;
– the engine reaches its operating
temperature (if the engine was cold
when the reset key was pressed);
– when driving from an urban area
onto the open road.
With one of the journey parameters selected on the display, press button 2
or 3 until the display resets.
1.63
TRIP COMPUTER: trip settings (1/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
Interpreting the display selected
101668 KM
a) Total mileage and trip mileage recorder.
112. 4 KM
Fuel used
8.5 L
Fuel used
20 L
Average
7.2 L/100
1.64
b) Journey parameters.
Fuel used.
Fuel consumed since the last reset.
Average
Average fuel consumption since the last reset.
7.2 L/100
The value is displayed after having travelled at least
400 metres since the last reset.
TRIP COMPUTER: trip settings (2/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
Current
9.4 L/100
Interpreting the display selected
Current
9.4 L/100
Range
541 km
Range
541 km
Distance
52.2 km
Distance
Current fuel consumption.
This value is displayed above a speed of approximately
18 mph (30 km/h).
Estimated range with remaining fuel.
This range takes into account the average fuel consumption
since the last time the reset button was pressed. The value
is displayed after driving 400 metres.
Distance travelled since the last reset.
359 km
Average
89.6 km/h
Average
Average speed since the last reset.
The value is displayed after driving 400 metres.
89.6 km/h
1.65
TRIP COMPUTER: trip settings (3/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
Oil change in
30000km/24 MONTHS
Schedule Oil
Chg in 100km
Schedule Oil Chg
in 10 days
Interpreting the display selected
c) Mileage before oil change.
Distance remaining until the next oil change (displayed in
miles/kilometres and months), then when the time nears,
several scenarios are possible:
– distance/time remaining less than 900 miles
(1,500 km) or one month: the message “Schedule
Oil Chg in” or “Oil change in” is displayed accompanied by the nearest term (distance or time);
– range equal to 0 km/miles or service date reached:
the message “Oil changerequired” is displayed accompanied by warning light ©.
The vehicle requires an oil change as soon as possible.
NB: depending on the vehicle, the mileage before an oil change varies according to the driving style (frequent driving at low
speed, door-to-door journeys, extensive use at idle speed, towing a trailer etc.). The distance remaining until the next oil change
can therefore decrease more quickly in some cases than the actual distance travelled.
The oil change intervals are independent of the vehicle’s maintenance schedule: please refer to your vehicle’s Maintenance
Document.
Resetting: to reset the mileage before an oil change, press and hold one of the display reset buttons for approximately 10 seconds until the display shows the range permanently.
1.66
TRIP COMPUTER: trip settings (4/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
Interpreting the display selected
FRONT TYRES
2.2
2.2
d) Tyre pressure monitor
Refer to the information on the “Tyre pressure monitor”
in Section 2.
REAR TYRES
2.2
2.2
1.67
TRIP COMPUTER: trip settings (5/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
Interpreting the display selected
e) Vehicle settings customisation menu.
Settings menu:
press and hold
Enables certain vehicle functions to be set (instrument panel language, parking
distance control, etc.). Refer to the information on “Vehicle settings customisation
menu” in Section 1.
f) Trip log.
No message available
Successive display:
– information messages (passenger airbag OFF etc.),
– operating fault messages (Check injection system, etc.).
1.68
TRIP COMPUTER AND WARNING SYSTEM: information messages
These can help in the vehicle starting phase, or give information about a selection or a driving status.
Examples of information messages are given in the following pages.
Examples of messages
Interpreting the display selected
« Battery low
start engine »
Indicates that the vehicle must be started to recharge the battery (eg. after the engine has been
switched off for some time whilst listening to the radio).
« Please remove
keycard »
« Checking control
functions »
« Traction control off »
Request to remove the RENAULT card from the reader when you leave the vehicle.
Displayed with the ignition on when the vehicle is running self-diagnostics.
Indicates that you have deactivated the ASR function.
« Turn steering
wheel + START »
Turn the steering wheel slightly whilst pressing the vehicle start button to unlock the steering
column.
« Auto Stop »
Indicates that the engine is on standby (related to the Stop and Start function – please see the information on “Stop and Start function” in Section 2).
« Steering wheel
not locked »
Indicates that the steering column has not been locked.
« Stop vehicle »
Indicates an electronic parking brake fault. Apply the electronic parking brake manually and ensure
that the vehicle is immobilised using a chock.
1.69
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages
These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as
soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The ©
warning light stays on. Examples of operating fault messages are given in the following pages.
Examples of messages
« Clean diesel filter »
Indicates the presence of water in the diesel filter.
« Check lighting »
Indicates a fault in the directional headlights.
« Check vehicle »
Indicates a fault on one of the pedal sensors or in the battery management
system.
« Check airbag »
Indicates a fault in the restraint system in addition to the seat belts. In the event
of an accident, it is possible that they may not be triggered.
« Check anti-pollution system »
« Check injection »
1.70
Interpreting the display selected
Indicates a fault in the vehicle’s particle filter system.
Indicates an engine fault.
TRIP COMPUTER AND WARNING SYSTEM: warning message
These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic
conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.
Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually
or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Examples of messages
Interpreting the display selected
« Engine failure hazard »
Indicates engine overheating, or an injection or engine oil pressure fault.
“Power steering fault” or
“Risk of steering locking”
Indicates a fault in the steering.
« Parking brake fault »
« Battery charging fault »
« Puncture »
Indicates an electronic parking brake fault. Apply the electronic parking brake manually
and ensure that the vehicle is immobilised using a chock.
Indicates a fault in the vehicle battery charging circuit (alternator etc.).
Indicates a puncture on the tyre displayed on the instrument panel.
1.71
VEHICLE SETTINGS CUSTOMISATION MENU
j) Parking sensor volume;
k) Language.
1
2
3
On equipped vehicles, this function,
which is integrated in the trip computer and warning system 1, allows you
to activate/deactivate some of the vehicle’s functions.
Accessing the settings
customisation menu
With the vehicle stopped, press
button 2 or 3 several times until the
message “Settings menu: press and
hold” is shown on display 1. Press
either button 2 or 3 for longer than 2 seconds to enter the menu.
1.72
Adjusting the settings
Press one of buttons 2 or 3 to select a
function to change:
a) Auto door locking while driving;
b) Unlock driver’s door only;
c) Auto rear wipe with reverse gear;
d) Auto dipped-beam headlights;
e) Front parking sensor;
f) Automaticmain beam lights;
g) Lane depart. warn. volume;
h) Lane depart. warn. sensitivity;
i) Rear parking sensor;
=
<
function activated
function deactivated
Once a line has been selected, keep
pressing button 2 or 3 to change the
function. If you select either “Parking
sensor volume” or “Language”, you will
have to make a further selection (sound
volume of the parking distance control
or instrument panel language). In this
case, make your selection and confirm
it by holding either button 2 or 3, the
~
value selected is shown by a
in
front of the line.
To exit the menu, press either button 2
or 3. It may be necessary to carry out
this operation several times.
The vehicle settings personalisation menu cannot be used when driving. At speed exceeding 12 mph
(20 km/h), the instrumental panel
display switches automatically back
to trip computer and warning system
mode.
CLOCK AND EXTERIOR TEMPERATURE
1
2
Vehicles equipped with a
navigation system, radio, etc.
External temperature
indicator
For vehicles which are not fitted with
buttons 2 and 3, refer to the specific
equipment instructions to discover the
special features.
Special note:
When the external temperature is between –3°C and +3°C, the °C characters flash (indicates risk of ice formation).
3
The time and, depending on the vehicle, the exterior temperature are displayed.
Resetting the clock 1
On equipped vehicles, buttons 2 and 3
are used to set the clock.
External temperature
indicator
Press button 2 to adjust the hours and
button 3 to adjust the minutes.
If the power supply is cut (battery
disconnected, supply wire cut, etc.),
the clock must be reset.
As ice formation is related
to climatic exposure, local
air humidity and temperature, the
external temperature alone is not
sufficient to detect ice.
We recommend that you do not
adjust these settings while driving.
1.73
REAR VIEW MIRRORS
Folding door mirrors
D
1
E
A B
C
3 2
The door mirrors automatically fold in
when the vehicle is locked (switch 2 in
position B). In this case, they will fold
out when the ignition is next switched
on.
In any case, you can make the door
mirrors fold in (switch 2 in position C) or
fold out (switch 2 in position A).
Automatic mode is then deactivated. To
reactivate it, position switch 2 to B.
4
Door mirrors
Interior rear view mirror
Adjustment
Select the door mirror using switch 3,
then use button 1 to adjust it to the desired position.
Its position can be adjusted.
Heated door mirrors
Mirror de-icing is carried out at the
same time as rear screen de-icing.
Rear view mirror with lever 4
The driver’s door mirror
may have two clearly defined zones. Zone E shows
what can normally be seen
in an ordinary rear view mirror.
Zone D increases rear side visibility.
The objects in zone D look much
further away than they really are.
1.74
When driving at night, to avoid being
dazzled by the headlights of the vehicle
behind, depress the little lever located
behind rear view mirror 4.
Rear view mirror without lever 4
The rear view mirror darkens automatically at night if you are being followed
by a vehicle with its lights on.
AUDIBLE AND VISUAL SIGNALS
Direction indicators
Move stalk 1 parallel to the steering
wheel and in the direction you are going
to turn it.
2
One-touch mode
1
A
Horn
Press on the sides of the steering wheel
boss A.
Headlight flasher
Pull stalk 1 towards you to flash the
headlights.
When driving, it is possible that the
steering wheel may not be turned sufficiently to return the stalk automatically
to its starting position.
In this case, briefly turn stalk 1 to the intermediate position, then release it: the
stalk returns to its original point and the
indicator light flashes three times.
é
Hazard warning lights
Press switch 2. This switch activates all four direction indicators and
the side indicator lights simultaneously.
It must only be used in an emergency to
warn drivers of other vehicles that you
have had to stop in an area where stopping is prohibited or unexpected or that
you are obliged to drive under special
conditions.
Depending on the vehicle, the hazard
warning lights may come on automatically under heavy deceleration. You can
switch them off by pressing switch 2.
1.75
EXTERIOR LIGHTING AND SIGNALS (1/4)
Daytime running lights
function
1
2
3
1
Depending on the vehicle, the daytime
running lights come on automatically
when the engine is started. To activate
or deactivate this function, refer to the
information on the “Vehicle settings
customisation menu” in Section 1.
á
Main beam headlights
With the dipped beam headlights lit, pull stalk 1 towards you. This
indicator light on the instrument panel
comes on.
u
Side lights
k
Dipped beam
headlights
Turn the ring 2 until the symbol
is opposite mark 3. This indicator light
on the instrument panel comes on.
Manual operation
Turn the ring 2 until the symbol is opposite mark 3. This indicator light on the
instrument panel comes on.
1.76
Automatic operation
(depending on vehicle)
Turn ring 2 until the AUTO symbol is opposite mark 3: with the engine running,
the dipped beam headlights switch on
or off automatically depending on the
brightness of the light outside, without
any action on stalk 1.
If driving on the left in a left-hand
drive vehicle (or vice versa), drivers
must have the lights adjusted by an
authorised dealer for the duration of
the trip.
To return to the dipped headlight position, pull stalk 1 towards you again.
Before driving at night,
check that the electrical
equipment is operating correctly and adjust the headlight beams (if your vehicle is not
carrying its normal load). As a general precaution, check that the lights
are not obscured (by dirt, mud,
snow or objects being transported).
EXTERIOR LIGHTING AND SIGNALS (2/4)
Automatic main beam
headlights
Depending on the vehicle, this system
switches the main beam headlights on
and off automatically. The function uses
a camera located behind the interior
rear-view mirror to detect vehicles that
are following and coming in the opposite direction.
Activation
Turn ring 2 until the AUTO symbol is opposite mark 3.
Pull stalk 1 to activate main beam
headlights.
Warning light
strument panel.
comes on the in-
Deactivation
The main beam headlights come on automatically if:
– exterior light is weak;
– no other vehicles or lighting are detected;
– the vehicle speed is above approximately 30 mph (45 km/h).
If any of the above conditions are not
fulfilled, the system switches to dipped
beam headlights.
– pull stalk 1 again;
or
– turn ring 2 to a position other than
AUTO.
Using the portable navigation system at night in the
windscreen area below the
camera may disturb the operation of the “automatic main beam
headlights” system (risk of reflection
on the windscreen).
Turning on the fog lights deactivates
the system and prevents it from
being activated.
Warning light
strument panel.
goes out on the in-
The system may encounter difficulties under certain conditions, including:
– extreme weather conditions (rain,
snow, fog, etc.);
– obstruction in front of the windscreen or camera;
– when a following or oncoming vehicle has weak or hidden lighting;
– incorrect settings for the front
headlights;
– reflecting systems.
The “automatic main beam headlights” system should under no circumstances be used to replace driver attention and responsibility with regard
to vehicle lighting and adapting to light, visibility and traffic conditions.
1.77
EXTERIOR LIGHTING AND SIGNALS (3/4)
1
2
Directional headlights
Depending on the vehicle, with the
dipped beam headlights on and under
certain conditions (speed, steering
wheel angle, forwards gear selected,
etc.) when cornering, the dipped beam
headlights move to light the inside of
the bend.
Operating faults
Depending on the vehicle, when the
message “Check lighting” appears on
the instrument panel along with the
© warning light, this indicates that
there is a lighting fault.
Consult an approved dealer.
1.78
Special note:
– If the dipped beam headlights are
manually switched on and if the light
is sufficient, the directional headlights will remain fixed;
– If the lights come on automatically
when cornering, the directional
headlights will start working from the
next time the vehicle corners;
– When the dipped beam headlights
are switched on with the engine
running and the vehicle stationary,
the lights move to reinitialise themselves. If not, there is a system fault.
Switching off the lights
There are two possibilities:
– manually, move ring 2 to position 0;
– automatically, the lights will go out
when the engine is switched off, the
driver’s door is opened or the vehicle
is locked. In this case, the next time
the engine is started the lights will be
switched back on according to the
position of the ring 2.
NB: if the fog lights are lit, the lights are
not switched off automatically.
“See-me-home lighting”
function
This function allows you to briefly switch
on the dipped beam headlights (to provide light when opening a gate, etc.).
With the engine and lights off and
the ring 2 in the position 0, pull stalk 1
towards you: the dipped beam headlights come on for approximately thirty
seconds. To increase this duration, you
may pull the stalk up to four times (total
time restricted to two minutes). The
message “See-me-home” along with
the times the lights will be on for is displayed on the instrument panel to confirm this action.
To switch off the lights before they go
out automatically, turn ring 2 to any position, then return it to position 0.
EXTERIOR LIGHTING AND SIGNALS (4/4)
g
1
5
Front fog lights
Turn centre ring 5 on stalk 1
until the symbol faces mark 6, then release it.
Operation of the fog lights depends on
the exterior lighting position selected,
and an indicator light will light up on the
instrument panel.
6
f
Switching off the lights
Turn ring 5 again until mark 6 is opposite the symbol for the fog light that you
wish to switch off. The corresponding
indicator light on the instrument panel
goes out.
The front and rear fog lights switch off
when the exterior lights are switched
off.
Rear fog light
Turn centre ring 5 on the stalk
until the symbol faces mark 6, then release it.
Lights-on reminder buzzer
If the lights are on after the engine is
switched off, a warning beep sounds
when the driver’s door is opened to
warn you that the lights are still on.
Operation of the fog lights depends on
the exterior lighting selected, and an indicator light will light up on the instrument panel.
To avoid inconveniencing other road
users, remember to switch off the rear
fog light when it is no longer needed.
When driving in fog or snow, or
when transporting objects which are
higher than the roof, the headlights
do not come on automatically.
Switching on the fog lights remains
the responsibility of the driver: the
indicator lights on the instrument
panel inform you whether the fog
lights are lit (indicator light on) or not
(indicator light not on).
1.79
ADJUSTING THE HEADLIGHT BEAM HEIGHT
Examples of positions for adjusting
control A according to the load
Five door
Three door
Driver alone or with front
passenger
0
0
Driver with one front
passenger and one rear
passenger
0
0
Driver with one front
passenger and two or three
rear passengers
1
1
Driver with one front
passenger, three rear
passengers and luggage
3
3
A
On vehicles fitted with this function,
control A allows you to adjust the height
of the beams according to the load.
Turn control A downwards to lower the
headlights and upwards to raise them.
For vehicles not fitted with control A,
adjustment is automatic.
If driving on the left in a left-hand
drive vehicle (or vice versa), drivers
must have the lights adjusted by an
authorised dealer for the duration of
the trip.
1.80
WINDSCREEN WASH/WIPE (1/2)
Vehicle fitted with front
windscreen wiper rain sensor
1
1
E
2
A
B
C
D
F
A park
B automatic wiper function.
When this position is selected, the
system detects water on the windscreen and triggers the wipers at a
suitable wiping speed. It is possible to change the triggering threshold and the time sweeps by turning
ring 2:
– E: minimum sensitivity
Vehicle fitted with intermittent
windscreen wipers
A park
B intermittent wiping
The wipers will pause for several
seconds between sweeps. It is
possible to change the time between sweeps by turning ring 2.
Special note
When driving the vehicle, the wiping
speed slows down whenever the vehicle stops. For example, fast wiping
speed will slow to normal wiping speed.
As soon as the vehicle moves off,
wiping will return to the speed originally
selected.
If stalk 1 is operated, it overrides and
cancels the automatic function.
– F: maximum sensitivity
note: in foggy weather or during
snowfalls, the wiping is not automatically triggered and remains under
the driver’s control.
C normal wiping speed
D fast wiping speed
C normal wiping speed
D fast wiping speed
For all vehicles, position C can be
accessed with the ignition on and
positions B and D can only be accessed with the engine running.
1.81
WINDSCREEN WASH/WIPE (2/2)
Headlight washers
1
Headlights on
On equipped vehicles, hold stalk 1
pulled towards you for about 1 second,
and the headlight washers and windscreen washers will be activated at the
same time.
1
A
Note: when the minimum windscreen
washer fluid level is reached, the headlight washer system may be deprimed.
D
Fill the windscreen washer fluid and
then activate the windscreen washer,
with the engine running, to reprime
the system.
Windscreen washer
When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in position A (park).
With the ignition on, pull stalk 1 then
release.
A brief pull will trigger a single sweep
of the wipers, in addition to the windscreen washer.
A longer pull will trigger three sweeps
of the wipers followed, a few seconds
later, by a fourth, in addition to the windscreen washer.
1.82
B
C
Risk of injury.
In freezing or snowy weather, ensure
they are not stuck to the windscreen
(including the central area located
behind the interior rear-view mirror)
and the rear screen before starting
the wipers (risk of motor overheating).
Before any action on the
windscreen (washing the
vehicle, de-icing, cleaning
the windscreen, etc.) return
stalk 1 to position A (park).
Risk of injury and/or damage.
REAR SCREEN WASH/WIPE
1
p
With the ignition on, push the stalk.
A
2
Y
Rear screen washer/
wiper
Rear screen wiper
With the ignition on, turn ring A
on stalk 1 to align the symbol with
mark 2 then release it.
To stop the operation, pivot ring A
again.
Wiping frequency varies with vehicle
speed.
Check the condition of the wiper
blades. You are responsible for their
service life:
– they must remain clean: clean
the blades, windscreen and
rear screen regularly with soapy
water;
– do not use them when the windscreen or rear screen are dry;
– free them from the windscreen or
rear screen when they have not
been used for a long time.
In all cases, replace them as soon
as they begin to lose efficiency: approximately once a year.
Before using the rear wiper, check
that no object obstructs the travel of
the blade.
Do not use the wiper arm to open or
close the tailgate.
1.83
FUEL TANK (1/3)
Fuel grade
A
Use a high-grade fuel that complies
with the legislation in force in each
country and which must conform to the
specifications given on the label on the
cover B. Refer to the information on
“Engine specifications” in Section 6.
B
C
Useable fuel tank capacity:
59 litres approximately.
With the vehicle unlocked, to open the
compartment B, place your finger into
the recess C.
Diesel versions
It is essential to use diesel fuel that
conforms with the information given on
the label inside cover B.
Petrol versions
It is essential to use unleaded petrol.
The octane rating (RON) must conform
to the specifications on the label inside
fuel filler flap B. Refer to the information
on “Engine specifications” in Section 6.
Vehicles running on ethanol-based
fuel
It is essential to use unleaded petrol or
fuel containing a maximum of 85% ethanol (E85).
In very cold conditions, it may be very
difficult or even impossible to start the
engine. To avoid this problem, use unleaded petrol or, on equipped vehicles,
use the heater integrated in the engine:
connect the special end of the extension piece supplied into the socket integrated into the radiator grille and the
other end into a 220V socket for at least
6 hours before starting.
Note: you may notice an increase in
fuel consumption with this type of fuel.
Valve A is integrated into the filler pipe.
For details on filling the fuel tank, refer
to the information on “Filling with fuel”.
To close it, press on the fuel filler flap by
hand, as far as it will go.
Never press valve A with your fingers.
Do not wash the filler area with a high pressure washer.
1.84
Do not mix even small
amounts of petrol (unleaded or E85) with diesel.
Do not use ethanol-based
fuel if your vehicle is not compatible
with this fuel.
Do not add additive to the fuel –
otherwise you risk damaging the
engine.
FUEL TANK (2/3)
Filling with fuel
With the ignition off, insert the nozzle to
open valve A and insert it fully before
turning it on to fill the fuel tank (risk of
splashing).
Keep the nozzle in this position throughout the entire filling operation.
When the pump cuts out automatically
at the end of the filling procedure, a
maximum of two further filling attempts
may be made, as there must be sufficient space in the fuel tank to allow for
expansion.
1
Make sure that no water enters the fuel
tank during filling. The valve A and its
surround must remain clean.
Petrol versions
Using leaded petrol will damage the
antipollution system and may lead to a
loss of warranty.
To ensure that the fuel tank is not filled
with leaded petrol, the fuel tank filler
neck contains a restrictor fitted with a
foolproof system which only allows
the nozzle for unleaded petrol to be
used (at the pump).
Persistent smell of
fuel
If you notice a persistent
smell of fuel you should:
– stop the vehicle as soon as traffic conditions allow and switch off
the ignition;
Vehicle fitted with the Stop and
Start function
To fill up with fuel, the engine must
be stopped (and not on standby):
stop the engine by pressing the
engine stop button 1 (please refer
to the information on “Starting and
stopping the engine” in Section 2).
– switch on the hazard warning
lights and ask your passengers
to leave the vehicle and to keep
away from traffic;
– contact an approved Dealer.
1.85
FUEL TANK (3/3)
2
1
3
Running out of fuel on diesel
versions
Vehicles with priming bulb 2
After a breakdown caused by completely running out of fuel, the system
must be reprimed before the engine is
restarted:
Fill the tank with at least 8 litres of
diesel fuel.
Press priming bulb 2 several times.
The engine can now be restarted.
If the engine does not start after several
attempts, contact an approved Dealer.
1.86
Vehicles without priming bulb 2
Insert the RENAULT card into the 3
card reader. Press the start button 1
without pressing any of the pedals. Wait
a few minutes before starting. This will
enable the fuel circuit to be primed. If
the engine does not start, repeat the
procedure.
No modifications whatsoever are permitted on
any part of the fuel supply
system (computers, wiring,
fuel circuit, injector, protection
covers, etc.) as this may be dangerous (such work must be undertaken
by qualified Network personnel).
Section 2: Driving
(Advice on use relating to fuel economy and the environment)
Running in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting, stopping the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stop and Start Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special features of petrol versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special features of diesel versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handbrake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advice: antipollution and fuel economy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tyre pressure monitoring system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driver correction devices and aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lane departure warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking distance control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reversing camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic gearbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
2.3
2.6
2.9
2.10
2.11
2.11
2.12
2.15
2.18
2.19
2.22
2.26
2.28
2.31
2.35
2.39
2.41
2.1
RUNNING IN
Petrol version
Diesel version
For the first 600 miles (1,000 km), do
not exceed 78 mph (130 km/h) in the
highest gear, or 3,000 to 3,500 rpm.
For the first 1,000 miles (1,500 km),
do not exceed 80 mph (130 km/h) in
the highest gear, or 2,500 rpm. After
completing this mileage you may drive
faster, although you may only expect
top performance after approximately
3,600 miles (6,000 km).
You may only expect top performance
from your vehicle after approximately
1,800 miles (3,000 km).
Service intervals: refer to the
Maintenance Document for your vehicle.
During the running in period, do not accelerate hard while the engine is still
cold and do not let the engine over-rev.
Service intervals: refer to the
Maintenance Document for your vehicle.
2.2
STARTING, STOPPING THE ENGINE (1/3)
Starting the vehicle
– For vehicles with automatic gearboxes, set the lever to position P.
1
2
Remote control RENAULT
card
When you get into the vehicle, insert the
RENAULT card fully into card reader 2.
To start, press button 1. If a gear is engaged, depress the clutch pedal to start
the vehicle.
3
Hands-free RENAULT card
The RENAULT card must be inserted
in card reader 2 or in detection zone 3.
To start, depress the brake or clutch
pedal and press button 1. If a gear
is engaged, the vehicle may only be
started by depressing the clutch pedal.
– If one of the starting conditions is not
met, the message “Press brake +
START”, “Press clutch + START” or
“Gear leverto P” is displayed on the
instrument panel.
– In some cases, it will be necessary to move the steering wheel
while pressing the ignition button 1
to assist in unlocking the steering
column; a message on the instrument panel (“Turn steering wheel +
START”) warns of this.
Special note: if starting the engine
when the outdoor temperature is very
low (below - 10 ° C): hold down the
clutch pedal until the engine starts.
“Hands-free” starting with
the tailgate open
In this case, the RENAULT card must
not be located in the luggage compartment.
2.3
STARTING, STOPPING THE ENGINE (2/3)
1
2
For other functions:
Operating faults
– vehicles with remote control
RENAULT card, insert the card into
reader 2;
In certain cases, the hands-free
RENAULT card may not work:
– vehicles with a RENAULT “handsfree” card, with the card in the passenger compartment or inserted in
the card reader 2, press button 1
without depressing the pedals.
Note: if there is a card in the reader,
pressing button 1 starts the engine.
(switching on the ignition)
2.4
– near to appliances operating on the
same frequency as the card (monitor, mobile phone, video game, etc.);
– vehicle located in a high electromagnetic radiation zone.
The message “Please insert keycard”
appears on the instrument panel.
Insert the RENAULT card fully into card
reader 2.
Accessories function
Once you have gained access to your
vehicle, you may use some of its functions (radio, navigation, wipers, etc.).
– when the RENAULT card battery is
drained, flat battery, etc.
Driver’s responsibility
Never leave your vehicle
with the RENAULT card
inside and never leave a
child (or a pet) unsupervised, even
for a short while.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or by locking the
doors.
Risk of serious injury.
STARTING, STOPPING THE ENGINE (3/3)
Special note
If the card is no longer in the reader
when you try to switch the engine off,
the message “No keycard Press and
hold” will appear on the instrument
panel: press the button 1 for longer
than two seconds.
1
2
Hands-free RENAULT card
With the card in the vehicle, press
button 1: the engine will stop. The steering column is locked when the driver’s
door is opened or the vehicle is locked.
Conditions for stopping the
engine
The vehicle must stationary, with the
lever positioned in N or P for vehicles
with an automatic transmission.
Remote control RENAULT
card
With the card in reader 2, press
button 1: the engine will stop. Removing
the card from the reader locks the steering column.
When you leave your vehicle, especially if you have
your RENAULT card with
you, check that the engine
is completely switched off.
If the card is no longer in the passenger
compartment when you try to switch
the engine off, the message “No keycard Press and hold” appears on the instrument panel: press the button 1 for
longer than two seconds.
With the engine switched off, any accessories being used (radio, etc.) will
continue to function for approximately
10 minutes.
When the driver’s door is opened, the
accessories stop working.
Driver’s responsibility
Never leave your vehicle
with the RENAULT card
inside and never leave a
child (or a pet) unsupervised, even
for a short while.
There is a risk that they could start
the engine or operate electrical
equipment (electric windows etc.)
and trap part of their body (neck,
arms, hands, etc.).
Risk of serious injury.
Never switch off the ignition before
the vehicle has stopped completely.
Once the engine has stopped, the
brake servo, power-assisted steering, etc. and the passive safety devices such as air bags and pretensioners will no longer operate.
2.5
STOP AND START function (1/3)
This system enables a reduced fuel
consumption and lower greenhouse
gas emissions.
The system is activated automatically
when the vehicle is started.
While driving, the system stops the
engine (standby) when the vehicle is
at a standstill (traffic jam, traffic lights,
etc).
The message “Auto Stop” on the instrument panel indicates that the engine is
on standby.
The vehicle equipment remain operational while the engine is stopped.
The engine will restart as soon as you
press the clutch pedal and move into
gear.
System operating conditions
– the gearbox is in neutral;
– the clutch pedal is released;
and
– the vehicle is travelling at less than
3 km/h.
panel).
2.6
Do not drive off when the
engine is on standby (the
message “Auto Stop” is displayed on the instrument
Under certain conditions, the engine
can restart on its own in order to guarantee your safety and comfort.
This can occur especially when:
– the outdoor temperature is too low or
too high (less than around 0 °C or
higher than around 30 °C);
– the “Clear View” function is activated
(please see “Automatic Climate
Control” in Section 3);
Engine standby is activated if:
– the vehicle has been driven since its
last stop;
Special feature of the automatic
engine re-start
Special feature of vehicles equipped with an
electronic parking brake
– the battery is not sufficiently charged;
If the engine is put on
standby (the message “Auto Stop”
is displayed on the instrument
panel), the electronic parking brake
is not applied automatically.
– repeated pressing on the brake
pedal or braking system requirement;
Before getting out of the
vehicle, you must switch
off the ignition by pressing
the engine stop (please see
“Starting, stopping the engine”).
– the vehicle speed is above 7 km/h
(downhill slope, etc.);
– ...
Engine on standby - braking
assistance is no longer operational.
STOP AND START function (2/3)
Conditions preventing the
standby of the engine
Certain conditions prevent the system
from using the engine standby function,
including when:
– reverse gear is engaged;
– the bonnet is not locked;
– the driver’s door is not closed;
– the driver’s seatbelt is not fastened;
– the outdoor temperature is too low or
too high (less than around 0 °C or
higher than around 30 °C);
– the “Clear View” function is activated
(please see “Automatic Climate
Control” in Section 3);
– the engine coolant temperature is
too low;
– automatic particle filter cleaning is
underway;
or
– ...
The message “Auto Stop Unavailable”
on the instrument panel indicates that
the engine is on standby.
Special cases
– While the system is operating, and
the engine is stopped (traffic jam,
traffic lights, etc.), if the driver gets
out of their seat or unfastens their
seatbelt and opens the driver’s door,
the ignition will be switched off and,
depending on the vehicle, the electronic parking brake will be automatically deployed. To restart and reactivate the Stop and Start system,
press the start button (please see
“Starting, stopping the engine”).
– In the event of the engine stalling,
if the system is operational, press
down the clutch pedal as far as it will
go to restart.
– the battery is not sufficiently charged;
– the difference between the vehicle
interior temperature and the automatic climate control instruction is
too high;
To fill up with fuel, the engine must
be stopped (and not on standby):
always stop the engine by pressing
the engine stop button (please see
“Starting, stopping the engine)”.
Deactivate the Stop and
Start function for any operation performed in the engine
compartment.
2.7
STOP AND START function (3/3)
The system is automatically reactivated
each time the vehicle is started using
the start button (please see “Starting,
stopping the engine)”.
1
Operating faults
When the message “Check Stop &
Start” appears on the instrument panel
and the integrated warning light 2 lights
up on the switch 1, the system is deactivated.
Please consult an authorised dealer.
2
Deactivating, activating the
function
Press switch 1 to deactivate the function. The message “Stop & Start deactivated” will appear on the instrument
panel and the integrated warning light 2
on the switch will light up.
Pressing this again will reactivate the
system. The message “Stop & Start activated” will appear on the instrument
panel and the integrated warning light 2
on the switch 1 will go out.
2.8
Before getting out of the
vehicle, you must switch
off the ignition by pressing
the engine stop (please see
“Starting, stopping the engine”).
In the event of an emergency, the engine can be
restarted by pressing on the
clutch pedal if the Stop and
Start function is activated.
SPECIAL FEATURES OF PETROL VERSIONS
The following operating conditions:
– driving for long periods when the low
fuel level warning light is lit;
– using leaded petrol;
– using fuel or lubrication additives
which are not approved.
Or operating faults such as:
– faulty ignition system, running out of
fuel or disconnected spark plugs resulting in the engine misfiring or cutting out when driving;
– loss of power,
as they may cause the catalytic converter to overheat and thus reduce its
efficiency, or damage it irreparably
and cause heat damage to the vehicle.
If you notice any of the above operating
faults, have the necessary repairs carried out as soon as possible by an approved Dealer.
These faults may be avoided by regularly taking your vehicle to an approved
Dealer at the intervals specified in the
Maintenance Service Booklet.
Starting problems
To avoid damaging the catalytic converter, do not keep trying to start the
engine (using the start button, or by
pushing or towing the vehicle) without
having identified and corrected the
starting fault.
If the fault cannot be identified, do not
keep trying to start the engine, but contact an approved Dealer.
Do not park the vehicle or
run the engine in locations
where combustible substances or materials such
as grass or leaves can come into
contact with the hot exhaust system.
2.9
SPECIAL FEATURES OF DIESEL VERSIONS
Diesel engine speed
Diesel engines are fitted with injection
equipment which prevents the engine
speed being exceeded irrespective of
the gear selected.
If the message “Check antipollution
system” is displayed along with warn-
Ä
ing lights
and ©, consult an
authorised dealer immediately.
Precautions to be taken in
winter
To avoid any faults in icy weather:
– ensure that the battery is always fully
charged,
– always keep the diesel tank relatively full to avoid water vapour condensing in it and accumulating at the
bottom of the tank.
When driving, depending on the fuel
grade used, it is possible that white
smoke may be emitted.
This is due to the exhaust particle filter
being cleaned automatically, and does
not affect the way the vehicle runs.
Running out of fuel
If the tank has been completely
drained, the system must be reprimed
after the tank is refilled: see information
on the “fuel tank” in section 1 before restarting the engine.
2.10
Do not park the vehicle or
run the engine in locations
where combustible substances or materials such
as grass or leaves can come into
contact with the hot exhaust system.
GEAR LEVER/HANDBRAKE
Handbrake
To release:
1
Pull lever 2 up slightly, press button 3
and then lower the lever to the floor.
2
To apply:
Pull the lever 2 upwards and make sure
the vehicle is immobilised.
3
Make sure that the handbrake is properly released
when driving (red indicator
light off), otherwise overheating, or even damage, may
occur.
Selecting reverse gear
Vehicles with manual gearbox: follow
the grid drawn on knob 1, and depending on the vehicle, lift ring against the
gear lever knob to select reverse.
Vehicle with automatic gearbox: refer
to the information on the “Automatic
gearbox” in Section 2.
The reversing lights will come on as
soon as reverse gear is selected with
the ignition on.
An impact to the underside of the vehicle while
manoeuvring (e.g.: striking a post, raised kerb or
other street furniture) may result in
damage to the vehicle (e.g.: deformation of the rear axle).
To avoid any risk of accident, have
your vehicle checked by an approved Dealer.
When stationary and depending on the slope and/or
vehicle load, it may be necessary to pull up the handbrake at least two extra notches and
engage a gear (1st or reverse gear)
for vehicles with a manual gearbox
or position P for vehicles with an automatic transmission.
2.11
ELECTRONIC PARKING BRAKE (1/3)
Note:
To indicate that the electronic parking
brake is released, a beep sounds and
the message “Apply parking brake” appears on the instrument panel:
1
– with the engine running: when the
driver’s door is opened;
2
3
– with the engine switched off (eg.
when the engine stalls): when a front
door is opened.
In this case, pull and release switch 3 to
apply the electronic parking brake.
Automatic operation
The electronic parking brake ensures vehicle immobilisation when the
engine is stopped and engine Start/
Stop button 1 is pressed.
In all other instances, e.g. engine stalling, the electronic parking brake is not
applied automatically. Manual mode
must be used.
For certain country-specific model versions, the automatic brake application
function is not activated. Refer to the information on “Manual operation”.
2.12
To confirm that the electronic parking
brake is applied, the message “Parking
}
brake on” and warning light
on the instrument panel and warning
light 2 on the switch 3 light up.
After the engine is switched off, indicator light 2 goes out several minutes
after the electronic parking brake has
}
been applied and indicator light
goes out when the vehicle is locked.
Automatic releasing of the
electronic parking brake
The brake will be released as soon as
the vehicle moves, by accelerating with
a gear selected and the engine running.
Before leaving the vehicle,
check that the electronic
parking brake is fully applied. Indicator light 2 on
}
switch 3 and indicator light
on the instrument panel light up to
show that the parking brake is applied but go out when the doors are
locked.
ELECTRONIC PARKING BRAKE (2/3)
Special cases
4
2
3
1
When parking on a slope or towing a
trailer, pull switch 3 for a few seconds
to obtain the maximum braking effect.
To park the vehicle without applying the
electronic parking brake (if there is a
risk of freezing, for example):
– with the engine running and
RENAULT card in reader 4, switch
off the engine by pressing engine
Start/Stop button 1;
– select a gear (manual gearbox) or
position P (automatic gearbox);
Manual operation
You can control the electronic parking
brake manually.
Applying the electronic parking
brake
Pull switch 3. Indicator lights 2 and
}
Brief stop
To manually activate the electronic
parking brake, (when stopping at a red
light, or stopping when the engine is
running, etc.): pull and release switch 3.
The brake is released as soon as the
vehicle is started up again.
– depress the brake pedal and press
switch 3 at the same time;
– remove the RENAULT card from the
card reader.
light up on the instrument panel.
Releasing the electronic parking
brake
With the ignition on, depress the brake
pedal then press button 3: indicator
lights 2 and
}
go out.
2.13
ELECTRONIC PARKING BRAKE (3/3)
Versions with an automatic
gearbox
For safety reasons, automatic release
is deactivated when the driver’s door
is open or not shut properly and the
engine is running (in order to prevent
the vehicle from moving without the
driver). The “Release parking brake
manually” message appears on the
instrument panel when the driver depresses the accelerator.
Never leave your vehicle
without moving the selector lever to position P or N.
This is because when the
vehicle is stationary with the engine
running and a gear engaged, the
vehicle may begin to move if you
accelerate.
There is a risk of accidents.
2.14
Operating faults
– If there is a fault, the © warning
light illuminates on the instrument
panel accompanied by the “Check
parking brake” message and, in
some cases, the
light.
}
warning
– If there is an electronic parking brake
fault, warning lights ® light up
accompanied by the “Parking brake
fault” message, a beep and, in certain cases, warning light
}
.
This means that you must stop as
soon as traffic conditions allow.
Contact an approved Dealer as soon
as possible.
If no lights or sounds are apparent, this indicates a fault
in the instrument panel. This
indicates that it is essential
to stop immediately (as soon as traffic conditions allow). Ensure that the
vehicle is correctly immobilised and
contact an approved Dealer.
It is therefore essential to
immobilise the vehicle by
engaging first gear (manual
gearbox) or position P (automatic gearbox). If the slope requires it, chock the vehicle.
ADVICE: antipollution, fuel economy and driving (1/3)
Your vehicle complies with criteria for
recycling and recovering vehicles at the
end of their service life which will come
into force in 2015.
Some parts of your vehicle have therefore been designed to facilitate future
recycling.
These parts are easy to remove so
that they can be recovered and reprocessed by recycling companies.
By virtue of its design, moderate fuel
consumption and initial settings, your
vehicle also conforms to current antipollution regulations. The manufacturer is actively striving to reduce pollutant exhaust gas emissions and to
save energy. But the fuel consumption
of your vehicle and the level of pollutant
exhaust gas emissions are also your
responsibility. Ensure that it is maintained and used correctly.
Aiding fuel economy
Depending on the vehicle, in order to
optimise consumption, an indicator light
on the instrument panel will inform you
of the best moment to upshift or downshift gears:
\
[
shift up a gear;
shift down a gear.
Maintenance
It is important to remember that failure to
respect antipollution regulations could
lead to legal action being taken against
the vehicle owner. In addition, replacing
engine, fuel supply system and exhaust
components with parts other than those
originally recommended by the manufacturer may alter your vehicle so that
it no longer complies with antipollution
regulations.
Have your vehicle adjusted and
checked by an approved Dealer, in accordance with the instructions given in
your maintenance schedule: they will
have all the equipment necessary for
ensuring that your vehicle is maintained
to its original standard.
Engine adjustments
– ignition: this does not require adjustment.
– spark plugs: for optimum fuel economy, efficiency and performance
the specifications laid down by our
Design Department must be strictly
applied.
If the spark plugs have to be
changed, use the make, type and
gap specified for your vehicle’s
engine. Contact an approved dealer
for this.
– idle: this does not require adjustment.
– air filter, diesel filter: a clogged element reduces performance. It must
be replaced.
2.15
ADVICE: antipollution, fuel economy and driving (2/3)
Exhaust gas monitoring
system
– Sporty driving uses a lot of fuel: drive
with a light right foot.
– Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release
the accelerator pedal.
– Do not try to maintain the same
speed up a hill, accelerate no more
than you would on the level. Keep
your foot in the same position on the
accelerator pedal.
– Double declutching and accelerating
before switching off are unnecessary
in modern vehicles.
– Bad weather, flooded roads:
The exhaust gas monitoring system will
detect any operating faults in the vehicle’s antipollution system.
If this system malfunctions, toxic substances may be released into the atmosphere or damage may occur.
This warning light on the instrument panel will indicate if
there are any faults in the system:
This lights up when the ignition is
switched on and goes out when the
engine is started.
– If it lights up continuously, consult an
approved Dealer as soon as possible;
– if it flashes, reduce the engine speed
until the light stops flashing. Contact
your approved dealer as soon as
possible.
Ä
2.16
Driving
– Drive carefully for the first few miles
until the engine reaches its normal
operating temperature, rather than
let it warm up while the vehicle is stationary.
– Speed is expensive.
– Do not overrev the engine in the intermediate gears.
Always use the highest gear possible without labouring the engine.
On versions with an automatic gearbox, it is preferable to keep the gear
lever in position D.
– Avoid sudden acceleration.
Do not drive through floods
if the water is above the
lower edge of the wheel
rims.
Obstructions to the driver
On the driver’s side, only
use mats adapted to the vehicle that attach to the preinstalled parts, and regularly check
their mounting. Do not place several
mats on top of each other.
Risk of pedals jamming
ADVICE: antipollution, fuel economy and driving (3/3)
– In vehicles fitted with air conditioning, it is normal to observe an
increase in fuel consumption (especially in urban conditions) when
it is used. For vehicles fitted with
manual air conditioning, switch off
the system when it is not required.
Advice for reducing consumption
and therefore helping to preserve
the environment:
If the vehicle has been parked in the
sun, open the doors for a few moments to let the hot air escape before
starting the engine.
Advice on use
– Electricity is fuel; switch off all the
electrical components which are
not really needed. However (safety
first), keep your lights on when the
visibility is bad (“see and be seen”).
– Use the air vents. Driving with the
windows open at 60 mph (100 km/h)
will increase fuel consumption by
4%.
– Never fill the fuel tank right to the
brim to avoid overflow.
– Do not leave an empty roof rack
fitted to the vehicle.
– It is better to fit a trailer for bulky objects.
– When towing a caravan, fit a wind
deflector and adjust it carefully.
– Avoid using the car for door-to-door
calls (short journeys with long waits
in between) because the engine
never reaches its normal operating
temperature.
Tyres
– An underinflated tyre increases fuel
consumption.
– The use of non-recommended tyres
can increase fuel consumption.
2.17
ENVIRONMENT
Your vehicle has been designed with
respect for the environment in mind for
its entire service life: during production,
use and at the end of its life.
This commitment is illustrated by the of
the manufacturer eco² signature.
Emissions
Manufacture
Our vehicles are also equipped with a
particle filter system including a catalytic converter, an oxygen sensor and
an active carbon filter (the latter prevents vapour from the fuel tank being
released into the open air).
Your vehicle has been manufactured at
a factory which complies with a policy
to reduce the environmental impact
on the surrounding areas (reduction of
water and energy consumption, visual
and noise pollution, atmospheric emissions and waste water; sorting and reusing waste).
Your vehicle has been designed to
emit fewer greenhouse gases (CO2)
while in use, and therefore to consume
less fuel (eg. 140 g/km, equivalent to
5.3 l/100 km for a diesel vehicle).
For certain diesel vehicles, this system
also has a particle filter to reduce the
volume of soot particles emitted.
Please make your own
contribution towards
protecting the environment
too
– Worn parts replaced in the course of
routine vehicle maintenance (vehicle battery, oil filter, air filter, batteries, etc.) and oil containers (empty or
filled with used oil) must be disposed
of through specialist organisations.
2.18
– At the end of the vehicle’s service
life, it should be sent to approved
centres to ensure that it is recycled.
– In all cases, comply with local legislation.
Recycling
Your vehicle is 85% recyclable and
95% recoverable.
To achieve these objectives, many of
the vehicle components have been designed to enable them to be recycled.
The materials and structures have
been carefully designed to allow these
components to be easily removed and
reprocessed by specialist companies.
In order to preserve raw material resources, this vehicle incorporates numerous parts made from recycled plastics or renewable materials (vegetable
or animal-derived materials such as
cotton or wool).
TYRE PRESSURE MONITOR (1/3)
If the vehicle is equipped with the function, this system monitors the tyre pressure.
1
The tyre pressure can be adjusted
when cold (please refer to the information on “Tyre pressures”).
If tyre pressures cannot be checked
when the tyres are cold, the recommended pressures should be increased
by 0.2 to 0.3 bar (3 PSI).
2
Operating principle
Each wheel (except for the emergency
spare wheel) has a sensor in the inflation valve which periodically measures
the tyre pressure.
Never deflate a hot tyre.
3
The system informs the driver via the
display 1 and on-board computer 2 that
the tyres are sufficiently inflated and
warns if they are underinflated or leaking.
This system monitors the tyre pressure.
Depending on the vehicle, the information is displayed on the instrument
panel. In this case, they appear:
This function is an additional driving aid.
However, the function does
not take the place of the
driver. It cannot, therefore, under
any circumstances replace the vigilance or the responsibility of the
driver.
Check the tyre pressures, including
the emergency spare wheel, once a
month.
– with the ignition on, when scrolling
through the on-board computer information by pressing control 3 (please
refer to the information on the “Onboard computer” in Section 1);
– or if there is a fault when driving
(refer to the following pages to find
out more about the warning messages).
Changing a wheel
If you wish to change your wheels (fitting winter tyres etc.), the system will
reset itself automatically after approximately two minutes driving at a minimum speed of 12 mph (20 km/h).
Changing a wheel
The system may take several minutes depending on
use for the new wheel positions and pressures to be recognised; check the tyre pressures after
all operations.
2.19
TYRE PRESSURE MONITOR (2/3)
1
« Puncture »
2
Wheel F indicates that the wheel concerned is punctured or severely underinflated. Replace it or contact an authorised dealer if it is punctured. Top up the
tyre pressure if the wheel is deflated.
E
This message appears along with the
® warning light.
“Tyre pressure sensors absent” or
“Check tyrepressure sensors”
F
Display
« Adjust tyre pressure »
The display 1 on the instrument panel
and on-board computer 2 informs you
of any tyre pressure faults (flat tyre,
punctured tyre, system fault, etc.).
A shaded wheel F indicates a deflated
tyre.
« Inflate tyres for motorway »
If all four wheels F are shaded, the tyre
pressure is not suitable for the driving
speed. Slow down or inflate all four
tyres to “motorway pressure” (refer to
the label located on the label on the
edge of the driver’s door).
2.20
If one wheel E disappears, this indicates that the sensor on this wheel is
missing or faulty (e.g. if the emergency
spare wheel is fitted).
TYRE PRESSURE MONITOR (3/3)
Emergency spare wheel
If the vehicle is equipped with an emergency spare wheel, it will not have a
sensor. When it is fitted to the vehicle,
the message “Tyre pressure sensors
absent” is displayed on the instrument
panel.
Tyre repair product and
inflation kit
Because the valves are specially designed, only use equipment approved
by the approved network.
Replacing wheels/tyres
This system requires specific equipment (wheels, tyres, sensors, etc.).
Contact an authorised dealer to replace
the tyres and to find out about available accessories compatible with the
system: the use of any other accessory
could affect the correct operation of the
system or damage a sensor.
2.21
DRIVER CORRECTION DEVICES AND AIDS (1/4)
Depending on the vehicle, this is composed of:
– the ABS (anti-lock braking
system);
– electronic stability control ESC
with understeer control and traction control ASR;
– emergency brake assist with, depending on the vehicle, braking
anticipation;
– hill start assistance.
These functions are an additional aid in the event of
critical driving conditions,
enabling the vehicle behaviour to be adapted to suit the driving
conditions.
However, the functions do not take
the place of the driver. They do
not increase the vehicle’s limits
and should not encourage you
to drive more quickly. Therefore,
they can under no circumstances
replace the vigilance or responsibility of the driver when manoeuvring
the vehicle (the driver must always
be ready for sudden incidents which
may occur when driving).
2.22
ABS (anti-lock braking
system)
Under heavy braking, the ABS prevents
the wheels from locking, allowing the
stopping distance to be managed and
keeping control of the vehicle.
Under these circumstances, the vehicle can be steered to avoid an obstacle
whilst braking. In addition, this system
can increase stopping distances, particularly on roads with low surface grip
(wet ground etc.).
You will feel a pulsation through the
brake pedal each time the system is
activated. The ABS does not in any way
improve the vehicle’s physical performance relating to the road surface and
roadholding. It is still essential to follow
the rules of good driving practice (such
as driving at a safe distance from the
vehicle in front etc.).
In an emergency, apply firm and
continuous pressure to the brake
pedal. There is no need to pump
it repeatedly. The ABS will modulate the force applied in the braking
system.
Operating faults:
x
–
© and
–
,
, © and ® lit
up on the instrument panel alongside
the message “Braking system fault”:
this indicates a fault in the braking
system.
lit up on the instrument panel alongside messages “Check ABS”, “Check braking system” and “Check ESC”: ABS,
ESC and emergency brake assist
are deactivated. Braking is always
enabled;
xD
In both cases, consult an approved
Dealer.
Your braking systems
are partially operational.
However, it is dangerous
to brake suddenly and
it is essential to stop immediately,
as soon as traffic conditions allow.
Contact an approved dealer.
DRIVER CORRECTION DEVICES AND AIDS (2/4)
Electronic stability control
ESC with understeer control
and traction control ASR
Electronic stability control ESC
This system helps you to keep control
of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip
on a bend, etc.).
Operating principle
A sensor in the steering wheel detects
the direction selected by the driver.
Other sensors throughout the vehicle
measure the actual direction.
The system compares driver input to
the actual trajectory of the vehicle and
corrects the trajectory if necessary by
controlling the braking of certain wheels
and/or engine power. In the event that
the system is engaged, indicator light
flashes on the instrument panel.
Understeer control
Operating faults
This system optimises the action of the
ESC in the case of pronounced understeer (loss of front axle road holding).
When the system detects an operating fault the message “Check ESC” and
warning light © appear on the instrument panel.
Traction control ASR
This system helps to limit wheelspin of
the drive wheels and to control the vehicle when pulling away accelerating or
decelerating.
In this case, the ESC and ASR are deactivated. Consult an approved dealer.
Operating principle
Using the wheel sensors, the system
measures and compares the speed of
the drive wheels at all times and slows
down their over-rotation. If a wheel is
starting to slip, the system brakes automatically until the drive supplied becomes compatible with the level of grip
under the wheel again.
The system also adjusts the engine
speed to the grip available under the
wheels, independently of the pressure
exerted on the accelerator pedal.
2.23
DRIVER CORRECTION DEVICES AND AIDS (3/4)
The traction control ASR offers additional safety, it is recommended that
you do not drive with the function disabled. Correct this as soon as possible
by pressing switch 1 again.
1
Note: the function is reactivated automatically when the ignition is switched
on or when a speed of approximately
24 mph (40 km/h) is exceeded.
Emergency brake assist
This system supplements the ABS
and helps reduce vehicle stopping distances.
Disabling the function ASR
Operating principle
In some situations (driving on very wet
ground: snow, mud, etc. or driving with
snow chains fitted), the system may
reduce the engine output to limit wheelspin. If this is not required, it is possible
to deactivate the function by pressing
switch 1.
The system is for detecting an emergency braking situation. In this case,
the braking assistance immediately develops maximum power and may trigger ABS regulation.
The message “Traction control off” is
displayed on the instrument panel to
inform you.
2.24
ABS braking is maintained as long as
the brake pedal is applied.
Hazard warning lights switching on
Depending on the vehicle, these may
light up in the event of sudden deceleration.
Operating faults
When the system detects an operating fault the message “Check braking system” appears on the instrument
panel along with the © warning
light.
Consult an approved dealer.
Braking anticipation
Depending on the vehicle, when you
rapidly release the accelerator, the
system anticipates the braking manoeuvre in order to reduce stopping
distances.
Special cases
When using the cruise control:
– if you use the accelerator, when you
release it, the system may be triggered;
– if you do not use the accelerator, the
system will not be triggered.
DRIVER CORRECTION DEVICES AND AIDS (4/4)
Hill start assistance
This device assists the driver when
starting on hills (ascending or descending). It prevents the vehicle from rolling
forwards or backwards by automatically
applying the brakes when the driver lifts
their foot off the brake pedal to depress
the accelerator pedal.
System operation
It only operates when the gear lever is
in a position other than neutral (other
than N or P for automatic transmissions) and the vehicle is completely
stationary (brake pedal depressed).
The system holds the vehicle for approximately 2 seconds. The brakes are
then gradually released (the vehicle will
move according to the slope).
The hill start assistance
system cannot completely
prevent the vehicle from
rolling backwards in all situations (extremely steep gradients,
etc.).
In all cases, the driver may depress
the brake pedal to prevent the vehicle from rolling forwards or backwards.
The hill start assistance function
should not be used for prolonged
stops: use the brake pedal.
This function is not designed to immobilise the vehicle permanently.
If necessary, use the brake pedal to
stop the vehicle.
The driver must remain particularly
vigilant when driving on slippery or
low-grip surfaces and/or on hills.
Risk of serious injury.
2.25
LANE DEPARTURE WARNING (1/2)
This system notifies the driver when
they accidentally cross a continuous or
broken line.
This function uses a camera attached
to the windscreen, behind the rear-view
mirror.
–
–
–
–
–
–
This function is a driving aid in the event of the accidental crossing of
a continuous or broken line in the road. However, the function is not intended to replace the driver. The function can be disrupted under certain
conditions, including:
poor visibility (rain, snow, fog, dirty windscreen, glare of the sun, partially obscured road lines, etc.);
roads with tight bends;
closely following a vehicle in the same lane;
worn road markings, difficult to distinguish or spaced very widely apart;
narrow roads;
...
In this case, warning light
on the instrument panel goes out to indicate that
the function will not operate (lines not detected).
Under no circumstances should this function replace the driver’s care or responsibility whilst performing manoeuvres.
2.26
LANE DEPARTURE WARNING (2/2)
The function sounds the alarm if:
Adjustment
a line is crossed without activating the
indicator lights. The function alerts the
From the vehicle settings customisation
menu (please refer to the information
on the “Vehicle settings customisation
menu” in Section 1), you can:
– adjust the alert audio volume. To
do this, select “lane departure alert:
volume” (five levels);
– adjust the alert sensitivity. To do this,
select “lane departure alert: sensitivity” (three levels).
driver through a warning light
on the instrument panel, along with a
beep.
1
Activation
Press button 1: the warning light on
the 1 button lights up, accompanied by
the message “Lane departure warning
on” and a beep.
The function is set to notify the
driver if:
– the warning light on the 1 button
lights up;
and
– the vehicle speed is greater than approximately 45 mph (70 km/h);
and
– lines are detected.
Conditions for non-activation
of alerts
– Indicators activated or having been
activated less than approximately
four seconds prior to departing from
the lane;
– Very fast lane departure;
– Driving continuously on a line;
– On bends, the function allows for
slightly cutting the bend;
– ...
Deactivation
Press button 1 on the central rear-view
mirror.
The warning light on button 1 goes out,
accompanied by a message on the instrument panel “Lane departure warning off”.
Operating faults
In the event of a malfunction, a message “Lane departure warning check” is
displayed on the instrument panel, and
the warning light on button 1 stays off.
Consult an approved dealer.
Warning light
comes on on the
instrument panel to notify the driver.
2.27
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3)
6
7
1
2
5
3
The speed limiter function helps you
stay within the driving speed limit that
you choose, known as the limit speed.
4
Controls
1 Main “On/Off” switch.
2 Limit speed activation, storage and
increase switch (+).
3 Decrease limit speed (-).
4 Switch the function to standby (with
memorisation of the limit speed) (O).
5 Activation and recall of stored limit
speed (R).
2.28
Switching on
Press the side switch 1 . Warning
light 7 comes on, lit orange, and the
message “Speed limiter” appears on
the instrument panel, accompanied by
dashes in zone 6 to indicate that the
speed limiter function is activated and
waiting to store a speed limit.
To store the current speed, press
switch 2 (+): The limited speed will
appear in zone 6. The minimum stored
speed is 20 mph (30 km/h).
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3)
C
Varying the limit speed
Exceeding the limit speed
The limit speed may be changed by repeatedly pressing:
It is possible to exceed the limit speed
at any moment. To do this: press the
accelerator pedal firmly and fully
(beyond the kickdown point).
– switch 2 (+) to increase the speed;
– switch 3 (-) to decrease the speed.
2
5
3
While the speed is being exceeded, the
limit speed flashes on the instrument
panel and area C lights up red.
Then, as far as is possible, release
the accelerator pedal: the speed limiter function will return as soon as you
reach a speed lower than the stored
speed.
4
Limited speed cannot be maintained
Driving
If driving up or down a steep gradient,
the system is unable to maintain the
limit speed: the stored speed on the
instrument panel will flash and zone C
will light up in red to inform you of this
situation.
When a limited speed has been stored
and this speed is not reached, driving is
similar to driving a vehicle without the
speed limiter function.
Once you have reached the stored
speed, no effort on the accelerator pedal will allow you to exceed
the programmed speed except in an
emergency (refer to information on
“Exceeding the limit speed”).
The speed limiter function is
in no way linked to the braking system.
2.29
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3)
6
7
1
2
5
3
4
Putting the function on
standby
The speed limiter function is deactivated when you press switch 4 (O). In
this case, the speed limit will remain
stored and is no longer displayed in
zone 6 and the message “Memorised”
along with the stored speed will appear
on the display.
Recalling the limit speed
Switching off the function
If a speed has been stored, it can be recalled by pressing switch 5 (R).
The speed limiter function is deactivated if you press switch 1: in this case
a speed is no longer stored. The instrument panel orange indicator light 7
goes out to confirm that the function is
deactivated.
When the speed limiter is put on
standby, pressing switch 2 (+) reactivates the function without taking
into account the stored speed: it is
the speed at which the vehicle is
moving that is taken into account.
2.30
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4)
1
The cruise control function helps you to
maintain your driving speed at a speed
that you choose, called the cruising
speed.
This cruising speed may be set at any
speed above 20 mph (30 km/h).
2
This function is an additional driving aid. However,
the function does not take
the place of the driver.
Therefore, it can under no circumstances replace the driver’s responsibility to respect speed limits and to
be vigilant (the driver must always
be ready to brake). Cruise control
must not be used in heavy traffic, on
undulating or slippery roads (black
ice, aquaplaning, gravel) and during
bad weather (fog, rain, side winds
etc.).
There is a risk of accidents.
3
4
5
Controls
1 Main “On/Off” switch.
2 Limit speed activation, storage and
increase switch (+).
3 Decrease cruising speed (-).
4 Switch the function to standby
(with memorisation of the governed cruising speed) (O).
5 Activation with recall of stored governed cruising speed (R).
The cruise control function
is in no way linked to the
braking system.
2.31
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4)
B
C
6
7
A
1
5
2
3
4
Switching on
Activating cruise control
Driving
Press switch 1 on the side showing .
At a steady speed (above 20 mph
(30 km/h) approximately) press
switch 2 (+): the speed is stored. The
cruising speed will appear in zone 6.
Once a cruising speed is stored and
the cruise control function is active,
you may lift your foot off the accelerator pedal.
Warning light 7 comes on, lit green, and
the message “Cruise control” appears
on the instrument panel and dashes
appear in zone 6 to indicate that the
cruise control function is activated and
waiting to store a cruising speed.
Cruise control activation is confirmed
when area A lights up green in addition
to indicator light 7. Area B also lights
up green to indicate that the cruising
speed has been reached.
sary.
2.32
Important: you are nevertheless advised to keep
your feet close to the pedals
in order to react if neces-
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4)
B
Exceeding the cruising speed
C
6
The cruising speed may be exceeded
at any time by depressing the accelerator pedal. The cruising speed flashes
on the instrument panel along with the
illumination of zone C in red.
A
5
2
3
4
Adjusting the cruising speed
The cruising speed may be changed by
pressing the following repeatedly:
Putting the function on
standby
The function is suspended when you:
– press switch 4 (O);
– depress the brake pedal;
Then, release the accelerator: after a
few seconds, the vehicle will automatically return to its set cruising speed.
– depress the clutch pedal or shift into
neutral if the vehicle has an automatic gearbox.
Cruising speed cannot be
maintained
In all three cases, the cruising speed remains stored, it is no longer displayed in
zone 6 and the message “Memorised”
along with the stored speed will appear
on the instrument panel.
If driving up or down a steep gradient,
the system is unable to maintain the
cruising speed: the stored speed on the
instrument panel will flash and zone C
will light up in red to inform you of this
situation.
Standby is confirmed when zones A, B
and C go out.
– switch 2 (+) to increase the speed;
– switch 3 (-) to decrease the speed.
The cruise control function
is in no way linked to the
braking system.
2.33
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4)
B
C
7
A
1
5
2
3
4
Returning to the cruising speed
If a speed is stored, it can be recalled,
once you are sure that the road conditions are suitable (traffic, road surface,
weather conditions, etc.).
Press switch 5 (R) if the vehicle speed
is above 20 mph (30 km/h).
When recalling the stored speed
zone A lights up to confirm activation.
Zone B lights up as soon as the cruising speed is reached.
2.34
Note: if the speed previously stored is
much higher than the current speed,
the vehicle will accelerate more rapidly
to reach this threshold.
When the cruise control function is
put on standby, pressing switch 2 (+)
reactivates the cruise control function without taking into account the
stored speed: it is the speed at
which the vehicle is moving that is
taken into account.
Switching off the function
The cruise control function is deactivated if you press switch 1: in this case
a speed is no longer stored. The instrument panel green indicator light 7 and
zones A, B and C go out, confirming
that the function is deactivated.
Putting the cruise control
on standby or switching it
off does not cause a rapid
reduction in speed: you
must brake by depressing the brake
pedal.
PARKING DISTANCE CONTROL (1/4)
Rear parking distance control
1
Operation
When reverse gear is selected, most
objects which are less than approximately 1.20 metres from the rear of
the vehicle are detected and a beep
sounds.
This function is an additional aid that indicates the
distance between the vehicle and an obstacle whilst
reversing, using sound signals.
Operating principle
Ultrasonic detectors, installed in the
front or rear bumper depending on the
vehicle, measure the distance between
the vehicle and an obstacle whilst reversing.
This measurement is indicated by
beeps which become more frequent the
closer you get to the obstacle, until they
become a continuous beep when the
vehicle is approximately 30 centimetres
from the obstacle.
Note: the display 1 shows the vehicle
surroundings in conjunction with the
beeps.
Under no circumstances should it
replace the driver’s care or responsibility whilst reversing.
The driver should always look out
for sudden hazards during driving: always ensure that there are
no moving obstacles (such as a
child, animal, pram or bicycle, etc.)
or small, narrow objects such as
stones or posts in your path when
manoeuvring.
Automatic activation/deactivation of
the rear parking distance control
The system deactivates:
– depending on the model, when the
vehicle is stationary for more than
approximately 5 seconds and an obstacle is detected (such as when in a
traffic jam, etc.);
– when the vehicle is in neutral or
when the gearstick has been shifted
to N or P for automatic gearboxes;
– when the vehicle speed is above approximately 6 mph (10 km/h).
2.35
PARKING DISTANCE CONTROL (2/4)
Front parking distance
control
(depending on vehicle)
1
Operation
The parking distance control system
is only activated when the vehicle is
driven at a speed below approximately
6 mph (10 km/h).
Most objects located less than around
1 metre away from the front of the vehicle are detected and a beep is emitted.
The display 1 comes on.
Note: The display 1 shows the vehicle
surroundings and emits beeps.
Automatic activation/deactivation of
the front parking distance control
The system deactivates:
– when the vehicle speed is above approximately 6 mph (10 km/h);
– depending on the model, when the
vehicle is stationary for more than
approximately 5 seconds and an obstacle is detected (such as when in a
traffic jam, etc.);
– when the vehicle is in neutral or
when the gear lever has been
shifted to N or P for automatic gearboxes;
2.36
If there are obstacles located close to
both the front and rear of the vehicle,
only the closest of the two will be acknowledged and the corresponding
front or rear beep sound will be emitted. If obstacles are detected both at
the front and rear of the vehicle at the
same time, and they are both less than
30 centimetres away from the vehicle,
the corresponding front and rear beeps
will be emitted alternately.
An impact to the underside of the vehicle while
manoeuvring (e.g.: striking a post, raised kerb or
other street furniture) may result in
damage to the vehicle (e.g.: deformation of an axle).
To avoid any risk of accident, have
your vehicle checked by an approved Dealer.
PARKING DISTANCE CONTROL (3/4)
Prolonged deactivation of the
system
2
You may permanently activate or deactivate the front or rear parking distance
control separately.
From the customisation menu
3
Select line “Front parking sensor” or
“Rear parking sensor”, then activate or
deactivate the system (refer to the information on “Vehicle settings customisation menu” in Section 1):
<
=
Special features
Ensure that the ultrasonic sensors are
not obscured (by dirt, mud, snow, etc.).
Operating faults
When the system detects an operating
fault there will be a 5-second continuous beep as a warning. Consult an
approved dealer.
: function deactivated;
Adjusting the parking
distance control volume
function activated.
From the customisation menu
Select the “Parking sensor volume” line
to adjust the volume of the parking distance control and confirm by pressing
button 2 or 3 (please refer to the information on “Vehicle settings customisation menu” in Section 1).
When the vehicle is being driven at
a speed below approximately 6 mph
(10 km/h), certain noises (motorcycle, lorry, pneumatic drill, etc.) may
trigger the beeping sound.
2.37
PARKING DISTANCE CONTROL (4/4)
Operating faults
A
When the system detects an operating
fault, a beep sounds for approximately
3 seconds each time reverse gear is selected and is accompanied by the message “Check parking sensor” shown on
the instrument panel A. Please contact
an authorised dealer.
Park Assist
Rear parking sensor
Volume
Rear camera view settings
Image settings
Special features
Done
Adjusting the parking
distance control volume
Deactivating the system
From the multimedia display
You can deactivate the parking distance
control from the multimedia display.
Certain settings can be adjusted from
the multimedia display A. Please see
the equipment instructions for further
information.
Select “menu”, “Settings”, “Park Assist
”, then adjust the parking distance control volume by pressing + or -.
Ensure that the ultrasonic sensors are
not obscured (by dirt, mud, snow, etc.).
From the multimedia display
Select “menu”, “Settings”, “Park Assist
” then “Rear parking sensor” or “Front
parking sensor”. Activate or deactivate
the parking distance control and confirm your choice by selecting “Done ”.
When the vehicle is being driven at
a speed below approximately 6 mph
(10 km/h), certain noises (motorcycle, lorry, pneumatic drill, etc.) may
trigger the beeping sound.
2.38
REVERSING CAMERA (1/2)
3
2
4
C
B
1
A
Operation
3 moving guide line:
Moving into reverse gear, the camera 1
located near the number plate lights
provides a view of the area behind the
vehicle on the multimedia display 2,
accompanied by two moving or fixed
guide lines 3 and 4.
This is shown in blue on screen 2. It indicates the vehicle trajectory according
to the position of the steering wheel.
This system is initially used with the aid
of several gauges (mobile for trajectory
and fixed for distance). When the red
zone is reached, use the bumper image
to stop accurately.
Fixed gauge 4
The fixed clearance gauge comprises
coloured markers A, B and C, indicating the distance behind the vehicle:
This gauge remains fixed and indicates
the vehicle trajectory if the wheels are
in line with the vehicle.
Special feature
Make sure that the camera is not obscured (by dirt, mud, snow, etc.).
– A (red) approximately 30 centimetres from the vehicle;
– B (yellow) approximately 70 centimetres from the vehicle;
– C (green) approximately 150 centimetres from the vehicle.
2.39
REVERSING CAMERA (2/2)
2
Park Assist
The screen shows a reverse image.
Rear parking sensor
The frames are a representation
projected onto flat ground; this information must not be taken into
account when superimposed on a
vertical object or an object on the
ground.
Volume
Rear camera view settings
Image settings
Done
Activating, deactivating the
reversing camera
From the multimedia display 2, select
“menu”, “Settings”, “Park Assist” then
“Rear camera view settings”. Activate
or deactivate the reversing camera
and confirm your choice by selecting
“Done”.
You can also adjust the camera image
settings (brightness, contrast, etc.)
Objects which appear on the edge
of the screen may be deformed.
In very bright light (snow, vehicle in
sunshine etc.), the camera vision
may be adversely affected.
If the boot is open or poorly closed,
the message “Boot open” appears
and the camera display disappears.
This function is an additional aid. It cannot, therefore, under any circumstances replace the vigilance or the responsibility of the driver.
The driver should always pay attention to sudden incidents during driving: always ensure that there are no moving obstacles (such as a child,
animal, pram, bicycle, etc.) or small, narrow objects such as stones or posts in
your path when manoeuvring.
2.40
AUTOMATIC TRANSMISSION (1/3)
Driving in automatic mode
4
1
2
3
5
9
6
8
7
Selector lever 1
Operation
Display 3 on the instrument panel
shows the mode and gear selected.
With the gear lever 1 in position P,
switch on the ignition.
4:
To move out of position P, you must depress the brake pedal before pressing
unlocking button 2.
P: park
5:
R: reverse gear
6:
N: neutral
7:
D: automatic mode
8:
manual mode
9:
zone displaying gearbox mode or
gear engaged in manual mode
With the foot on the brake pedal (warning light c on the display 3 goes out),
move the lever out of position P.
Select position D. In most traffic conditions, you will not have to touch the
gear selector lever again: the gears will
change automatically at the right time
and at the most suitable engine speed
because the automatic system takes
into account the vehicle load and road
contour and adjusts itself to the particular driving style you have chosen.
Economical driving
When driving, always leave the lever
in position D, keeping the accelerator
pedal lightly depressed to ensure automatic gear changes at a lower engine
speed.
Accelerating and overtaking
Depress the accelerator pedal firmly
and fully (so that it goes beyond the
kickdown point).
This will enable you to change down
to the optimum gear within the
engine range.
Only engage D or R when the vehicle is stopped, with your foot on the
brake and the accelerator pedal released.
2.41
AUTOMATIC TRANSMISSION (2/3)
Driving in manual mode
Special circumstances
Parking the vehicle
With the selector lever in position D,
move the lever to the left. Shifting the
lever repeatedly allows you to change
gears manually:
– If the road contours and bends
do not allow you to stay in automatic mode (e.g.: in the mountains),
we recommend that you change to
manual mode.
This will prevent the automatic gearbox from changing gears repeatedly
when climbing, and permit engine
braking on long descents.
When the vehicle is stopped, move the
lever to position P while keeping your
foot on the brake pedal: the gearbox is
in neutral and the drive wheels are mechanically locked by the driveshaft.
– To move down through the gears,
push the lever backwards;
– To move up through the gears, push
the lever forwards.
The gear selected is displayed on the
instrument panel.
Special cases
Under certain driving conditions (e.g.
engine protection, or electronic stability program (ESP) operational etc.): the
automatic system may change gear automatically.
– In cold weather, to prevent the
engine from stalling, wait a few moments before shifting the selector
lever from position P or N and engaging D or R.
An impact to the underside of the vehicle while
manoeuvring (e.g.: striking a post, raised kerb or
other street furniture) may result in
damage to the vehicle (e.g.: deformation of an axle).
Likewise, to prevent incorrect manoeuvres, a gear change may be refused by
the automatic system: in this case the
gear display flashes for a few seconds
as a warning.
In very cold weather, the system
may prevent the gears from being
shifted in manual mode until the
gearbox reaches the right temperature.
2.42
Apply the handbrake or, depending
on the vehicle, ensure that the electronic parking brake is applied.
To avoid any risk of accident, have
your vehicle checked by an approved Dealer.
AUTOMATIC TRANSMISSION (3/3)
Operating faults
– When driving, if the “Check auto
gearbox” message appears on the
instrument panel, it indicates a fault.
Contact your approved Dealer as
soon as possible.
– When driving, if the message “Auto
gearbox overheating” appears on the
instrument panel, stop the vehicle to
allow the gearbox to cool down.
2
10
Contact your approved Dealer as
soon as possible.
– If a vehicle with an automatic
gearbox breaks down, refer to the
information on “Towing” in Section 5.
When setting off, if the lever is locked
in position P even though you are depressing the brake pedal and pressing
unlocking button 2, the lever can be released manually. To do this, press the
button by inserting an object into the
hole 10 and simultaneously press unlocking button 2 located on the lever.
2.43
2.44
Section 3: Your comfort
Air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air conditioning: information and advice on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric windows, Electric sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual window winder controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sun visor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Passenger compartment storage space and fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ashtray – Cigarette lighter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear bench seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear parcel shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot cover: estate models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot storage space and fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transporting objects: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
in the boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
towbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage net. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Roof bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multimedia equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
3.4
3.6
3.11
3.12
3.15
3.15
3.16
3.17
3.21
3.21
3.22
3.24
3.25
3.26
3.27
3.30
3.30
3.31
3.32
3.34
3.35
3.1
AIR VENTS: air outlets (1/2)
3
1
4
5
6
2
7
9
Depending on the vehicle:
7
1 left-hand side air vent
2 left-hand side window demister
outlet
3 windscreen demister outlets
4 centre air vents
5 right-hand side air vent
6 right-hand side window demister
outlet
3.2
7 passenger footwell heater outlets
8 centre console air vents
9 air conditioning control panel
8
AIR VENTS: air outlets (2/2)
1
2
1
4
2
3
2
Air flow
Direction
Turn control knob 1 (beyond the point
of resistance).
Right/left: move tabs 2 to the right or
left.
Up: maximum air flow.
Up/down: lower or raise tabs 2.
To remove bad odours from your vehicles, only use the systems designed
for this purpose. Consult an approved
Dealer.
Down: closed.
Turn control knob 3 (beyond the point
of resistance).
To the right: maximum air flow.
To the left: closed.
Depending on the vehicle, the air
vents 4 may be replaced by a storage compartment; refer to Section 3
“Passenger compartment storage/
fittings”.
Do not add anything to the
vehicle’s ventilation circuit
(for example, to remove
bad odours).
There is a risk of damage or of
fire.
3.3
MANUAL AIR CONDITIONING (1/2)
1
2
3
4
Distribution of air in the
passenger compartment
There are five air distribution options.
Turn control 4 to choose the distribution
option.
The air flow is directed to the
windscreen and the front side
window demisting vents.
W
i
The air flow is distributed between all the air vents, the
front side window demisting vents, the
windscreen demisting vents and the
footwells.
6
The controls
1 Adjusting the air temperature
5
Switching air conditioning on
or off
3 Air conditioning.
The air conditioning is switched on (indicator light on) or off (indicator light off)
using button 3.
4 Distribution of air in the passenger
compartment.
The air conditioning system is used
for:
5 De-icing/demisting of the rear screen
and, depending on the vehicle, the
door mirrors.
– lowering the temperature inside the
passenger compartment;
2 Adjusting the ventilation speed
6 Air recirculation.
3.4
– eliminating condensation more
quickly.
ó
G
J
The air flow is directed mainly
towards the footwells.
The air flow is directed towards
the dashboard vents and the
footwells.
All the air flow is directed to the
dashboard vents.
MANUAL AIR CONDITIONING (2/2)
1
2
3
4
“OFF" position:
the system is deactivated: the ventilation speed for the passenger compartment air is zero (vehicle stationary),
you can however still feel a slight flow
of air when the vehicle is moving.
Recommended demisting option:
W
Turn controls 1, 2 and 4 to the
position.
This is the quickest option for de-icing
and demisting the side windows and
the windscreen.
6
Switching the air
recirculation on
Press button 6: the integrated indicator
light comes on.
Under these conditions, air is taken
from the passenger compartment and
is recirculated, with no air being taken
from outside the vehicle.
Air recirculation is for:
– isolating the vehicle from the external atmosphere (driving in polluted
areas, etc.);
– lowering the passenger compartment temperature as quickly as possible.
Adjusting the ventilation
speed
Turn control 2 clockwise to increase the
air flow in the passenger compartment.
The passenger compartment is ventilated by blown air. The blower determines how much air enters but vehicle
speed has a slight effect on this.
Prolonged use of air recirculation
can lead to condensation forming on the side windows and windscreen, and discomfort due to the
use of non-renewed air in the passenger compartment.
We therefore advise you to return to
normal mode (external air) as soon
as the air recirculation function is
no longer required, by pressing the
button 6 again.
The de-icing function cannot be used with the air recirculation mode to avoid any risk of condensation forming on the windscreen and triggers the air conditioning and the integrated indicator light 3 to come on.
3.5
AUTOMATIC CLIMATE CONTROL (1/5)
2
1
6
13 11
10
1 and 6 Air temperature.
2, 3 and 4 Automatic programmes.
5 Distribution of air in the passenger
compartment.
7 Off button.
8 Air conditioning.
Automatic mode
5
12
The controls
3.6
4
3
9
8
7
9 De-icing/demisting of the rear screen
and, depending on the vehicle, the
door mirrors.
10 “Clear View” function.
11 Air recirculation.
12 Ventilation speed.
13 Display.
The automatic climate control system
guarantees comfort in the passenger compartment and good visibility
(except in the event of extreme conditions), whilst optimising consumption.
The system controls the ventilation
speed, air distribution, air recirculation, and starting and stopping the air
conditioning and air temperature. This
mode consists of a choice of three programmes:
AUTO: allows the selected comfort
level to be best attained, depending on
the exterior conditions. Press button 3.
SOFT: gently brings the temperature to
the desired comfort level. The comfort
level is then maintained gently and silently. Press button 2.
FAST: increases the operation of the
system to reach the desired comfort
level more quickly. Use this programme
when you have passengers in the rear.
Press button 4.
AUTOMATIC CLIMATE CONTROL (2/5)
2
1
3
Clear View function
4
12
Press button 10: the integrated indicator light comes on.
6
This function quickly demists and deices the windscreen, the rear screen,
the front side windows, and the door
mirrors (depending on the vehicle). The
air conditioning and rear screen de-icing functions must be activated.
Press button 9 to stop the heated rear
screen operating; the integrated indicator goes out.
13
A 10
Varying the ventilation speed
9
Temperature adjustment
In automatic mode, the system uses
the most suitable amount of air to reach
and maintain the desired comfort level.
Press button 1 or 6 to raise or lower the
left-hand 1 or right-hand 6 temperature.
Pressing button 3 for more than two
seconds sets the passenger temperature to the driver’s temperature.
You can still adjust the ventilation speed
by pressing buttons 12 to increase or
reduce the ventilation speed.
In this case, the ventilation speed,
which is no longer controlled automatically, appears in zone A on the display 13.
You can change the ventilation speed
by pressing button 12.
To exit this function, press:
– button 10 again,
– one of either button 2, 3 or 4.
Special note: the highest and lowest
settings allow the system to produce
maximum hot or cold temperature
levels (“LO” and “HI” on display 13).
Some buttons have an operating
tell-tale which indicates the operating status.
3.7
AUTOMATIC CLIMATE CONTROL (3/5)
3
The displayed temperature values
show a comfort level.
13
Switching air conditioning on
or off
In automatic mode, the system switches
the air conditioning system on or off,
depending on the climate conditions.
Press switch 8 to switch off the air
conditioning; the integrated indicator
comes on and “AC OFF” is shown on
the display 13.
8
When starting the engine, increasing or decreasing the value displayed will not allow the comfort level to be reached any more
quickly. The system will always optimise the temperature increase or
decrease (the ventilation system
does not start instantly at maximum
speed: it gradually increases). This
may take several minutes.
Generally speaking, unless there is
a particular reason not to, the dashboard air vents should remain open.
You are recommended to use automatic mode by selecting one of the automatic programmes AUTO, SOFT or FAST.
In automatic mode (indicator light for button 3 on), all heating and air conditioning
functions are controlled by the system.
You can also change the system selection, in this case, indicator light for button 3
will go out and the changed function, which is no longer controlled by the system,
is shown on display 13.
To return to automatic mode, press one of the AUTO, SOFT or FAST programmes.
3.8
AUTOMATIC CLIMATE CONTROL (4/5)
5
The air flow is directed to the
windscreen and the front side
window demisting vents.
Ø
×
The air flow is distributed between front side window demisting vents, the windscreen demisting vents and the footwells.
12
¿
¾
½
The air flow is directed mainly
towards the footwells.
The air flow is directed towards
the dashboard vents and the
footwells.
13
B
Rear screen de-icing/
demisting
Press button 9: the integrated indicator light comes on. This function permits rapid demisting/de-icing of the rear
screen and de-icing of the door mirrors
(on equipped vehicles).
To exit this function, press button 9
again. Demisting automatically stops
by default.
9
Adjusting the distribution
of air in the passenger
compartment
There are five air distribution options.
Press switch 5 to scroll through them.
The arrows located in area B on the
display 13 combine to show you the
distribution selected:
All the air flow is directed to the
dashboard vents.
In this situation, the distribution of air in
the passenger compartment, which is
no longer automatically controlled, appears on the display.
3.9
AUTOMATIC CLIMATE CONTROL (5/5)
Recycling
2
This function is managed automatically (operation is confirmed by warning light 14 on display 13), but you can
also activate it manually.
Note:
– during recirculation, air is taken from
the passenger compartment and
is recycled, with no air being taken
from outside the vehicle;
– air recirculation allows the external
atmosphere to be cut off (when driving in polluted areas, etc.);
– lowering the passenger compartment temperature as quickly as possible.
13 11
7
Stopping the system
Pressing button 11 allows air recirculation to be forced, in which case the integrated warning light comes on as well
as warning light 14.
Press button 7 to switch off the system;
in this case “OFF” is shown on the display 13. To switch the system on, press
one of the 2, 3 or 4 switches.
We therefore advise you to return to automatic mode as soon as the air recirculation function is no longer required,
by pressing button 11 again.
3.10
14
4
Manual use
Prolonged use of this position may lead
to odours, caused by non-renewal of
air, and the formation of condensation
on the windows.
The demisting/de-icing will still take
priority over the air recirculation.
3
AIR CONDITIONING: information and advice on use
Advice on use
In some situations, (air conditioning
off, air recirculation activated, ventilation speed at zero or low, etc.) you
may notice that condensation starts
to form on the windows and windscreen.
If there is condensation, use the
“Clear View” function to remove it,
then use the air conditioning in automatic mode to stop it forming again.
If the condensation does not clear,
use the FAST programme.
Note
Presence of water under the vehicle. After prolonged use of the air
conditioning system, it is normal for
water to be present under the vehicle. This is caused by condensation.
Fuel consumption
Operating faults
You will normally notice an increase
in fuel consumption (especially
when driving in town) when the air
conditioning is operating.
As a general rule, contact your approved Dealer in the event of an operating fault:
For vehicles fitted with manual air
conditioning, switch off the system
when it is not required.
Advice for reducing
consumption and therefore
helping to preserve the
environment:
Drive with the air vents open and
the windows closed.
– reduction in de-icing, demisting or air conditioning performance. This may be caused
by the passenger compartment
filter cartridge becoming clogged;
– no cold air is being produced.
Check that the controls are set
correctly and that the fuses are
sound. Otherwise, switch off the
system.
If the vehicle has been parked in
the sun, open the doors for a few
moments to let the hot air escape
before starting the engine.
Maintenance
Refer to the Maintenance Document
for your vehicle for the inspection
frequency.
Do not open the refrigerant fluid circuit. The fluid
may damage eyes or skin.
3.11
ELECTRIC WINDOWS, ELECTRIC SUNROOF (1/3)
These systems operate with the ignition on or off, until one of the front doors
is opened (limited to about 3 minutes).
Safety of rear occupants
The driver can disable operation of the electric windows and, depending on
the vehicle, the rear doors, by pressing switch 4. The indicator light integrated in the switch lights up to
confirm that the locks have been activated.
Driver’s responsibility
Never leave your vehicle with the
RENAULT card inside and never
leave a child (or a pet) unsupervised, even for a short while. They
may pose a risk to themselves or to
others by starting the engine, activating equipment such as the electric windows or by locking the doors.
If any part of the body becomes
trapped, reverse the direction of the
window immediately by pressing the
relevant switch.
Risk of serious injury.
1
5
2
4
6
3
Electric windows
Press or pull the switch to raise or lower
a window to the desired height (the rear
windows do not open fully);
One-touch mode
This mode works in addition to the operation of the electric windows described previously. It either operates on the
front windows only, or on all the windows.
Briefly press or pull the window switch
fully: the window is fully lowered or
raised. Pressing the switch again stops
the window moving.
From the driver’s seat, use switch:
1 for the driver’s side;
2 for the front passenger side;
3 and 5 for the rear passenger windows.
From the passenger seats, use
switch 6.
Note: if the window detects resistance
when closing (e.g.: fingers, branch of
a tree, etc.) it stops and then lowers
again by a few centimetres.
Avoid resting any objects against
a half-open window: there is a risk
that the electric window could be
damaged.
3.12
ELECTRIC WINDOWS, ELECTRIC SUNROOF (2/3)
Special note
A B
7
C
0
Your vehicle is equipped with an antipinch facility: when the sunroof encounters resistance whilst closing, (somebody’s fingers, etc.) it stops and then
moves back several centimetres.
D
9
8
Driver’s responsibility
Sun blind
Sunroof
– to open: push handle 7 upwards
and guide the blind as it retracts;
– Open the sun blind
– to close: pull handle 7 until it clicks
into the catch.
– To open slightly: turn button 9 to
position A;
– To open fully: turn button 9 to position B, C or D, depending on the
opening position required;
– To close: turn button 9 to position 0.
Never leave your vehicle
with the RENAULT card
inside and never leave a
child (or a pet) unsupervised, even
for a short while.
The reason for this is that the child
may endanger himself or others by
starting the engine, activating equipment such as the window winders
for example, or locking the doors.
If a body part gets trapped, reverse
the direction of travel as soon as
possible by turning button 9 fully to
the right (position D).
Risk of serious injury.
3.13
ELECTRIC WINDOWS, ELECTRIC SUNROOF (3/3)
Remote control window
closing
(for vehicles with one-touch windows
on all windows).
When you lock the doors from the outside, press the locking button on the
RENAULT card twice in quick succession, or on the driver's door in
hands-free mode, and all the windows
will close automatically.
It is recommended that the user only
operates the system when the vehicle can be seen clearly and no one is
inside.
Note: locking the doors using the
RENAULT card deactivates hands-free
mode.
Operating faults
Precautions during use
Electric windows
In case of a fault when closing a window,
the system reverts to normal mode:
pull the switch concerned up as often
as necessary to fully close the window
(the window will close gradually), hold
the switch (still on the closure side) for
three seconds then lower and raise the
window fully to reinitialise the system.
If necessary, contact your approved
Dealer.
– check that the sunroof is properly
closed before leaving your vehicle;
Electric sunroof
If the roof does not close, turn button 9
to the position 0 and then press button 8
until the roof is fully closed: consult an
approved Dealer.
Closing windows can cause
serious injury.
– clean the seal every three months
using products recommended by our
Technical Department;
– do not open the sunroof immediately after the vehicle has been in
the rain or after your car has been
washed.
– Vehicle with roof bars
As a general rule, if there is a load
on the roof, use of the sunroof is not
recommended.
Before using the sunroof, check the
objects and/or accessories (bike
racks, roof boxes, etc.) attached to
the roof bars: they should be properly arranged and secured and
should not interfere with the operation of the sunroof.
Contact your approved Dealer for
details of possible conversions.
If the vehicle is equipped
with this function, this action
will activate deadlocking.
Check that there is no-one
still inside the vehicle
3.14
Important: during this operation, the
sunroof anti-pinch facility is deactivated. Contact your approved
dealer as soon as possible.
MANUAL WINDOW WINDERS/INTERIOR LIGHTING (1/2)
2
3
4
1
5
Manual window winders
Courtesy light
Front door lights
Turn handle 1.
Tilt switch 3 to move it to the position
for:
Light 5 comes on when the door is
opened.
– permanent lighting;
– intermittent lighting, which comes
on when a door is opened. This
switches off after a time delay, once
the doors concerned have been
closed correctly;
– immediate switching off.
Map reading lights
(depending on vehicle)
Tilt switches 2 or 4.
When the doors or luggage compartment are unlocked and opened
the courtesy and footwell lights
come on temporarily.
3.15
INTERIOR LIGHTING (2/2)/SUN VISOR
6
7
8
9
Glove box light 6
Sun visor
Luggage compartment light 9
Light 6 comes on when the cover is
opened.
Lower the sun visor 7 over the windscreen or unclip it and turn it over the
side window.
Depending on the vehicle, light 9,
comes on when the luggage compartment is opened.
Courtesy mirrors
Slide cover 8, depending on the vehicle, and the mirror is lit.
3.16
PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (1/4)
3
1
Door pockets 1
2
Driver and passenger
underfloor storage
compartments 2
Sun visor storage 3
This can be used for storing motorway
tickets, cards, etc.
This storage compartment can be used
to hold the vehicle documentation, etc.
Ensure that no hard, heavy
or pointed objects are
placed in the “open” storage
compartments in such a
way that they may fall onto passengers during sudden turning, braking
or in the event of an accident.
Nothing should be placed
on the floor area in front of
the driver as such objects
may slide under the pedal
during braking manoeuvres, thus
obstructing its use.
3.17
PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (2/4)
4
5
6
A
7
Front centre armrest storage
compartment A
Centre console storage
compartments 6
Press button 4 and lift the cover 5.
Passenger storage
compartment
Pull handle 7 to open it.
The glove box can hold A4-size documents, a large bottle of water, etc.
The storage compartment is ventilated
and refrigerated.
Ensure that no hard, heavy
or pointed objects are
placed in the “open” storage
compartments in such a
way that they may fall onto passengers during sudden turning, braking
or in the event of an accident.
3.18
PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (3/4)
10
11
9
8
12
Door pockets 8
Storage compartment 9
Rear armrest storage
Lower armrest 12 and, depending on
the vehicle, lift cover 11 using unlocking handle 10.
3.19
PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (4/4)
15
14
16
13
Clothes hooks 13
Front seat storage
compartments 15
Rear centre console storage
compartments 16
Grab handle 14
This offers support and can be held
when the vehicle is being driven.
Do not use it for getting into or out of
the vehicle.
Depending on the vehicle, storage
compartment 16 may be replaced
by air vents; refer to Section 3 “Air
vents”.
3.20
ASHTRAY, CIGAR LIGHTER, ACCESSORIES SOCKET
1
3
2
2
Accessories sockets
Cigar lighter 1
Ashtray 2
You may use cigar lighter recess 1 or
socket 3 (depending on the vehicle).
They are designed for connecting accessories with a maximum power rating
of 120 Watts (voltage: 12V) which
have been approved by our Technical
Department.
With the ignition on, push in cigar
lighter 1, it will spring back with a click
when it is ready. Pull it out to use. After
use, replace it without pushing it all the
way in.
To open, lift the cover. To empty, pull the
ashtray towards you and it will be released from its housing.
Connect
accessories
with a maximum power of
120 Watts only.
Fire hazard.
If your vehicle is not fitted with a cigar lighter and an ashtray, these can be obtained from an approved Dealer.
3.21
REAR BENCH SEAT functions (1/2)
2
A
3
1
Sport tourer versions
To fold down the seatback
Depending on the vehicle, seatback A
can be folded down on its own to allow
long or bulky objects to be transported.
Ensure that the front seats are far
enough forward.
Press button 1
seatback(s) A.
and
lower
the
Lower the rear headrests (refer to the
information on the “Rear headrests” in
Section 1).
Place the seat belts 2 in their guides 3.
Before moving the seatback, put seat belt 2 in belt
guide 3 to avoid damaging
it.
3.22
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
REAR BENCH SEAT functions (2/2)
B
C
1
When moving the rear
bench seat, ensure that
nothing obstructs the anchorage points (part of the
body, a pet, gravel, cloth, toys, etc.).
The seat and the seatback may be
folded away to allow bulky objects to be
carried.
To fold away the seat base
Tilt seat base B against the front seats.
To fold down the seatback
After folding the seat base down,
remove the rear headrests (refer to the
section on “rear headrests”) then press
button 1 and lower the seatback(s) C.
In all situations, remove the rear
headrests (refer to the information on the “Rear headrests” in
Section 1).
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
When refitting the seatback, make sure it is correctly locked in place.
If seat covers are fitted,
make sure these do not prevent the
seatback latch from locking in.
Make sure that the seat belts are
positioned correctly.
Reposition the headrests.
3.23
TAILGATE
2
3
1
Press button 1 and lift the tailgate.
Opening manually from
inside the vehicle
To close
Special note:
Pull down the tailgate using handle 2
inside the tailgate to assist you.
If it is impossible to unlock the tailgate,
it can be done from inside.
To open
– access the luggage compartment by
folding forward the seatback(s) of
the rear bench seat,
– insert a pencil or similar object in
cavity 3 and slide the unit as shown
in the illustration,
– push the tailgate to open it.
3.24
REAR PARCEL SHELF
1
3
2
Removal
Unhook the two cords 1 (tailgate side).
Lift rear parcel shelf 2 slightly and pull it
towards you.
To refit it, proceed in reverse order to
removal.
Unclip mountings 3 on either side of
the parcel shelf, then remove the parcel
shelf via the luggage compartment.
To refit it, proceed in the reverse order
to removal.
Do not place any objects,
especially heavy or hard
objects, on the parcel shelf.
These may pose a risk to
the vehicle occupants if the driver
has to brake suddenly or if the vehicle is involved in an accident.
3.25
LUGGAGE COMPARTMENT COVER: estate models
B
1
A
To remove the flexible
section of the luggage cover
Pull handle 1 gently to release the pins
from their mounting points located on
each side of the luggage compartment.
Guide the luggage cover onto the roller.
Removing the luggage cover
Push the luggage compartment cover
to the left (movement A) and lift the
right-hand side of the inertia reel (movement B).
To refit the luggage compartment cover,
insert the left-hand side, then push it to
the left (movement A) and lower the
right-hand side of the inertia reel into its
housing.
Do not place any heavy or solid objects on the luggage cover. These may
pose a risk to the vehicle occupants if the driver has to brake suddenly or
if the vehicle is involved in an accident.
3.26
LUGGAGE COMPARTMENT STORAGE SPACE AND FITTINGS (1/3)
A
1
2
2
3
Storage under carpet 1
Anchorage points
To open, fold back carpet A.
Hooks 2 located on each corner of the
luggage compartment, allow the load to
be secured.
(depending on vehicle)
(Three- and five-seater versions)
Side straps
Side straps 3 are located either side of
the luggage compartment, and can be
used to store an oil can.
Always place objects being transported so that the heaviest items
are resting against the back of the
rear bench seat.
3.27
LUGGAGE COMPARTMENT STORAGE SPACE AND FITTINGS (2/3)
7
5
4
B
6
Anchorage points
Storage under carpet
Hooks 5, located on either side of the
luggage compartment, allow the load to
be secured.
To access storage compartments 7,
fold back section B using handle 4 and,
depending on the vehicle, lift flap 6.
(sport tourer version)
3.28
(sport tourer version)
LUGGAGE COMPARTMENT STORAGE SPACE AND FITTINGS (3/3)
8
4
9
C
C
Separating the luggage
compartment
On the back there is an elastic strip 9 to
hold small objects vertically in position.
(sport tourer version)
The loading area can be separated.
Turn locks 8 situated on either side of
the luggage compartment to the first
notch. Lift divider C using handle 4;
when the bolts make contact, push the
divider and it will lock.
Maximum weight: 20 kg.
Always place objects being transported so that the heaviest items
are resting against the back of the
rear bench seat.
3.29
TRANSPORTING OBJECTS IN THE BOOT (1/2)
A
Always place the objects to be transported so that their largest side rests
against the back of the rear bench seat
for normal loads (e.g.: A), or against the
back of the front seats when the rear
bench seatbacks are folded down.
If you have to place objects on the
folded seat back, it is vital that you
remove the headrests before folding
the seat back so that it can be folded as
flat as possible against the seat.
3.30
Always position the heaviest items directly on the
floor. Use the lashing points
on the floor of the luggage
compartment, if these are fitted to
the vehicle. The luggage should be
loaded in such a way that no items
will be thrown forward and strike the
occupants if the driver has to brake
suddenly. Fasten the rear seat belts,
even if the seats are not occupied.
TRANSPORTING OBJECTS IN THE BOOT (2/2)/TOWING
B
Three-door version B = 872 mm
Five-door version B = 867 mm
Estate version B = 1,070 mm
Permissible nose weight, maximum permissible towing weight,
braked and unbraked: refer to
the information on “Weights” in
Section 6.
For fitting and conditions of use,
refer to the equipment’s fitting instructions.
Please keep these instructions with
the rest of the vehicle documentation.
If the towbar ball obscures the registration plate or the rear fog lights, it
should be removed when not in use.
In all cases, comply with local legislation.
3.31
TRANSPORTING OBJECTS: luggage net (1/2)
Fitting the luggage net
behind the front seats
Inside the vehicle on each side:
1
A
– lift cover 1 to access the upper
mounting ring of the net;
– fix the net belt hook onto the ring;
2
Luggage net A
– to access the lower mounting 2 for
the net the first time you use it, contact an approved Dealer;
On equipped vehicles, this can be used
when transporting animals or luggage,
to separate them from the passenger
section.
– once you have accessed the lower
mounting, attach the hook 2 of the
net strap to the ring;
It can be positioned:
– adjust the net strap so that it is taut.
– behind the front seats;
– behind the rear bench seat.
The luggage net must not
be used to restrain or hold
objects.
Risk of injury.
3.32
TRANSPORTING OBJECTS: luggage net (2/2)
3
A
– in the luggage compartment, fix the
lower mounting strap hook on the
net to the anchorage point 4 located
under the luggage compartment
carpet;
– adjust the net strap so that it is taut.
4
Fitting the luggage net
behind the rear bench seat
Inside the vehicle on each side:
– Lift cover 3 to access the upper
mounting ring of the net;
– fix the net belt hook onto the ring;
The luggage net must not
be used to restrain or hold
objects.
Risk of injury.
3.33
ROOF BARS: ACCESS TO FIXING POINTS
Three door version
1
Sport tourer versions
For vehicles fitted with original roof
bars, the roof bars are fixed and
must not be removed. To change
them contact an approved Dealer.
Five-seater and sport tourer
versions
Open the doors to access the mounting points 1.
For information on the range of
equipment adapted to your vehicle, we advise you to consult an approved Dealer.
Refer to the fitting instructions for information on how to fit roof bars and
conditions of use.
If original roof bars, approved by our Technical
Department, are supplied
with screws, only use these
screws for attaching the roof bars to
the vehicle.
3.34
Please keep these instructions with
the rest of the vehicle documentation.
Maximum permissible load on
roof rack: refer to the information
on “Weights” in Section 6.
The fitting of roof bars is prohibited on
three door versions.
MULTIMEDIA EQUIPMENT
Multimedia systems
1
The equipment described below may
or may not be fitted to the vehicle, and
its location may vary, depending on the
vehicle navigation system version.
1
2
3
4
5
6
Multimedia display;
Radio;
Central control;
Multimedia sockets;
Steering column control;
Microphone.
6
2
5
4
3
Hands-free telephone
integrated control
On equipped vehicles, use microphone 6 and steering column control 5.
Using the telephone
To use this equipment, consult the
instructions for the equipment which
should be kept with the other vehicle documentation.
We remind you of the need
to conform to the legislation
in force concerning the use
of such equipment.
3.35
3.36
Section 4: Maintenance
Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine oil level: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
topping up, filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine oil change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Levels: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
engine coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
windscreen/headlight washer reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tyre pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bodywork maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior trim maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
4.3
4.3
4.5
4.6
4.8
4.8
4.9
4.10
4.10
4.11
4.12
4.14
4.16
4.1
BONNET
Closing the bonnet
2
Check that nothing has been left in the
engine compartment.
To close the bonnet again, hold the
bonnet in the middle and guide it down,
allowing a 30 cm gap before it is closed,
then release it. It will latch automatically
under its own weight.
1
To open, pull handle 1, located on the
left-hand side of the dashboard.
Unlocking the bonnet catch
To release it, lift tab 2.
The engine may be hot
when carrying out operations in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
4.2
Opening the bonnet
Lift the bonnet; you will need to guide it
as it is held by a strut.
Deactivate the Stop and
Start function for any operation performed in the engine
compartment.
Ensure that the bonnet is
properly locked.
Check that nothing is preventing the catch from locking (gravel, cloth, etc.).
Do not press down on the
bonnet: there is a risk that
the bonnet may accidentally
close.
After carrying out any work
in the engine compartment, check that nothing
has been left behind (cloth,
tools, etc.).
These may damage the engine or
cause a fire.
In the event of an impact,
even slight, against the radiator grille or bonnet, have
the bonnet catch checked
by an approved dealer as soon as
possible.
ENGINE OIL LEVEL: general information (1/2)
It is normal for an engine to use oil for
lubrication and cooling of moving parts
and it is normal to top up the level between oil changes.
However, contact your approved
Dealer if more than 0.5 litres is being
consumed every 600 miles (1,000 km)
after the running in period.
Oil change frequency: check the oil
level from time to time and certainly
before any long journey to avoid the
risk of damaging your engine.
3
Oil level
  
1
2
4
Reading the oil level
The oil level should be read with the vehicle on level ground, after the engine
has been switched off for some time.
The dipstick must be used to read
the exact oil level and make sure
that the maximum level has not been
exceeded (risk of engine damage).
Refer to the following pages.
The instrument panel display only
alerts the driver when the oil level is at
its minimum.
Minimum oil level warning on
the instrument panel
When the message “Checking control
functions” is displayed, press either
button 3 or 4.
If the level is above the minimum
level : the message “Oil level” will be
shown on the display with squares 1,
which are replaced by dashes when the
level drops 2.
Note: The detailed level cannot be displayed if the vehicle was previously
only driven for a short time.
If the level is at the minimum
The “Top up oil level” message and
warning light © are displayed on
the instrument panel.
It is vital to top up the oil as soon as
possible.
The display only warns the
driver if the oil level is at the
minimum level. It does not
inform the driver that the oil
level has exceeded the maximum
level as this can only be measured
using a dipstick.
4.3
ENGINE OIL LEVEL: general information (2/2)
B
A
C
B
A
Exceeding the maximum
engine oil level
The oil level should only be read with
the dipstick as explained above.
Reading the level using the
dipstick
– Remove the dipstick and wipe with a
clean, lint-free cloth;
– push the dipstick in as far as it will
go (for vehicles equipped with a captype dipstick C, screw the cap in as
far as it will go);
– take out the dipstick again;
– read the level: it should never fall
below minimum mark A or exceed
maximum mark B.
Once the operation has been completed, ensure that the dipstick is
pushed in as far as it will go or that
the “cap-type dipstick” is completely
screwed in.
4.4
If the oil level exceeds the maximum
level, do not start your vehicle and
contact an approved Dealer.
Deactivate the Stop and
Start function for any operation performed in the engine
compartment.
Under no circumstances
should maximum filling
level B be exceeded: this
could damage the engine
and the catalytic converter.
Consult your approved Dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
In order to prevent splashback, it is
recommended that a funnel be used
when topping up/filling with oil.
The engine may be hot
when carrying out operations in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
ENGINE OIL LEVEL: topping up, filling (1/3)
1
1
2
2
1
2
Topping up/filling
– Unscrew cap 1;
The vehicle must be parked on level
ground and the engine should be cold
(for instance, before the engine is
started up for the first time in the day).
– top up the level (as a guide, the capacity between the minimum and
maximum reading on the dipstick 2
is between 1.5 and 2 litres, depending on the engine);
Engine oil grade
Refer to the Maintenance Document for
your vehicle.
Do not exceed the max level and
do not forget to refit cap 1 and dipstick 2.
– wait for approximately 10 minutes to
allow the oil to flow into the engine;
– check the level using the dipstick 2
(as described above).
1
2
Once the operation has been completed, ensure that the dipstick is
pushed in as far as it will go or that the
cap-type dipstick is completely screwed
in.
4.5
ENGINE OIL LEVEL: topping up, filling (2/3)
1
2
1
2
Topping up/filling
– Unscrew cap 1;
The vehicle must be parked on level
ground and the engine should be cold
(for instance, before the engine is
started up for the first time in the day).
– top up the level (as a guide, the capacity between the minimum and
maximum reading on the dipstick 2
is between 1.5 and 2 litres, depending on the engine);
Engine oil grade
Refer to the Maintenance Document for
your vehicle.
Do not exceed the max level and
do not forget to refit cap 1 and dipstick 2.
4.6
– wait for approximately 10 minutes to
allow the oil to flow into the engine;
– check the level using the dipstick 2
(as described above).
Once the operation has been completed, ensure that the dipstick is
pushed in as far as it will go or that the
cap-type dipstick is completely screwed
in.
1
1
2
2
1
2
ENGINE OIL LEVEL: topping up, filling (3/3)/OIL CHANGE
Oil change
Service interval: refer to the
Maintenance Document for your vehicle.
1
2
Average capacities for oil change
including oil filter
(for information)
Engine 1.2 TCe
Engine 1.4 TCe
Engine 1.6 16V
Engine 2.0 16V
Engine 2.0 T
Engine 1.5 dCi
Engine 1.6 dCi
Engine 1.9 dCi
Engine 2.0 dCi
: 4.6 litres
: 4.5 litres
: 5.1 litres
: 4.4 litres
: 5.4 litres
: 4.5 litres
: 5.5 litres
: 5.1 litres
: 7.4 litres
Engine oil grade
Refer to the maintenance document for
your vehicle.
Filling: take care when
topping up the oil that
no oil drips onto engine
components - risk of fire.
Remember to refit the cap securely
as there is a risk of fire if oil splashes
onto hot engine components.
Consult your approved Dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
Engine oil change: if you
are changing the oil when
the engine is hot, be careful
not to scald yourself if the
oil overflows.
The engine may be hot
when carrying out operations in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
Deactivate the Stop and
Start function for any operation performed in the engine
compartment.
Never run the engine in an
enclosed space as exhaust
gases are poisonous.
4.7
LEVELS (1/3)
1
Checking intervals
Replacement intervals
Check the coolant level regularly
(very severe damage is likely to be
caused to the engine if it runs out of
coolant).
Refer to the Maintenance Document for
your vehicle.
If the level needs to be topped up, only
use products approved by our Technical
Department which ensure:
– protection against freezing;
– anticorrosion protection of the cooling system.
Coolant
With the engine switched off and on
level ground, the level when cold must
be between the “MINI" and "MAXI"
marks on coolant reservoir 1.
Top this level up when cold before it
reaches the MINI mark.
Deactivate the Stop and
Start function for any operation performed in the engine
compartment.
Consult your approved dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
The engine may be hot
when carrying out operations in close proximity. In
addition, the engine cooling
fan can come on at any moment.
No operations should be
carried out on the cooling
circuit when the engine is
hot.
Risk of injury.
4.8
Risk of burns.
LEVELS (2/3)
1
Level 1
Topping up
It is normal for the level to drop as
the linings become worn, but it should
never drop below the MIN line.
After any operation on the hydraulic circuit, a specialist must replace the fluid.
If you wish to check the disc and drum
wear yourself, you should obtain the
document explaining the checking procedure from our network or from the
manufacturer’s website.
Only use fluids approved by our
Technical Department (and taken from
a sealed container).
Replacement intervals
Refer to the Maintenance Document for
your vehicle.
Brake fluid level
The level should be read with the engine
switched off and on level ground. This
should be checked frequently, and any
time you notice even the slightest loss
in braking efficiency.
Consult your approved dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
4.9
LEVELS (3/3)/FILTERS
Liquid
Filters
Screen wash product (product with antifreeze in winter).
The replacement of filter elements (air
filter, passenger compartment filter,
diesel filter, etc.) is scheduled in the
maintenance operations for your vehicle.
Jets
1
Use a tool such as a needle to adjust
the height of the windscreen washer
jets.
Replacement intervals for filter elements: refer to the Maintenance
Document for your vehicle.
Windscreen/headlight washer
reservoir
Topping up
With the engine switched off, open
cap 1, fill until you can see the fluid,
then refit the cap.
NOTE
Depending on the vehicle, to find
out the fluid level, open cap 1 and
pull out the dipstick.
4.10
The engine may be hot
when carrying out operations in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
Deactivate the Stop and
Start function for any operation performed in the engine
compartment.
TYRE PRESSURE
F: tyre pressures for the rear wheels
(motorway).
G: tyre pressure for the emergency
spare wheel.
H: emergency spare wheel tyre dimension if different to the four tyres fitted to
the vehicle.
A
A
B
C
E
H
Label A
Open the door to read it.
Tyre pressures should be checked
when the tyres are cold.
If the tyre pressures cannot be checked
when the tyres are cold, increase the
pressures from 0.2 to 0.3 bar (or 3 PSI).
Never deflate a hot tyre.
D
F
G
C: tyre pressures for the front wheels
(non-motorway).
D: tyre pressures for the rear wheels
(non-motorway).
E: tyre pressures for the front wheels
(motorway).
Special note concerning fully laden
vehicles (Maximum Permissible All-Up
Weight) and towing a trailer: the maximum speed must be limited to 60 mph
(100 kph) and the tyre pressure increased by 0.2 bar.
Please refer to the information on
“Weights” in Section 6.
Tyre safety and use of snow chains:
Refer to the information on “Tyres” in
Section 5 for the servicing conditions
and, depending on the version, the use
of chains.
B: dimension of the tyres fitted to the
vehicle.
dealer.
When they need to be replaced, only tyres of the same make, size, type
and profile should be used on a single axle.
Tyres fitted to the vehicle should either be identical to those fitted
originally or conform to those recommended by your approved
4.11
BATTERY (1/2)
1
Depending on the vehicle, a system
continuously checks the battery charge
status. If the level drops, the message
“Battery low start engine” is displayed
on the instrument panel. In this case,
start the engine. Then the message
“Battery charging” appears on the instrument panel for the duration of the
charging time.
A
2
3
4
7
6
5
The charge status of your battery can
decrease especially if you use your vehicle:
– for short journeys;
– for driving in town;
The battery 1 does not require any
maintenance.
Handle the battery with care
as it contains sulphuric acid
which must not come into
contact with the eyes or
skin. If it does, wash the affected
area with plenty of cold water. If
necessary, consult a doctor.
Ensure that naked flames, red hot
objects and sparks do not come into
contact with the battery as there is a
risk of explosion.
– when the temperature drops;
– after extended use of consumers
(radio etc.) with the engine switched
off.
Label A
Observe the indications on the battery:
– 2 naked flames and smoking are forbidden;
– 3 eye protection required;
– 4 keep away from children;
– 5 explosive materials;
– 6 refer to the handbook;
– 7 corrosive materials.
The engine may be hot
during operations in close
proximity. In addition, the
engine cooling fan may
start at any moment.
Risk of injury.
4.12
BATTERY (2/2)
8
9
Replacing the battery
As this operation is complex, we advise
you to contact an authorised dealer.
Vehicle fitted with the Stop and Start
function
After changing or disconnecting the battery, the message “New battery?” appears on the instrument panel. Select
“Yes” or “No” with a short press on one
of the buttons 8 or 9, then confirm with
a long press on one of the two buttons.
Deactivate the Stop and
Start function for any operation performed in the engine
compartment.
dealer.
The battery is a specific
type, please ensure it is
replaced with the same
type. Consult an approved
4.13
BODYWORK MAINTENANCE (1/2)
A well-maintained vehicle will last
longer. It is therefore recommended to
maintain the exterior of the vehicle regularly.
Your vehicle has been treated with very
effective anti-corrosion products. It is
nevertheless subject to various outside
influences.
Corrosive agents in the atmosphere
– atmospheric pollution (built-up and
industrial areas),
– saline atmospheres (near the sea,
particularly in hot weather),
– seasonal and damp weather conditions (e.g. road salt in winter, water
from road cleaners, etc.).
What you should not do
Do not degrease or clean mechanical components (e.g. the engine compartment), underneath the body, parts
with hinges (e.g. inside the doors) and
painted plastic external fittings (e.g.
bumpers) using high-pressure cleaning equipment or by spraying on products not approved by our Technical
Department. Doing this could give rise
to corrosion or operational faults.
Wash the vehicle in bright sunlight or
freezing temperatures.
Do not scrape off mud or dirt without
pre-wetting.
Allow dirt to accumulate on the exterior.
Minor impacts
Allow rust to form following minor impacts.
Abrasive action
Dust and sand in the air, mud, road grit
thrown up by other vehicles, etc.
Do not use solvents not approved by
our Technical Department to remove
stains as this could damage the paintwork.
You should take a number of minor precautions in order to safeguard your vehicle against such risks.
4.14
Do not drive in snow or muddy conditions without washing the vehicle, particularly under the wheel arches and
body.
You should
Wash your car frequently, with the
engine off, with cleaning products recommended by the manufacturer (never
use abrasive products). Rinse thoroughly beforehand with a jet:
– spots of tree resin and industrial
grime;
– mud in the wheel arches and underneath the body which forms damp
patches;
– bird droppings, which cause a
chemical reaction with the paint that
rapidly discolours paintwork and
may even cause the paint to peel
off;
wash the vehicle immediately to
remove these marks since it is impossible to remove them by polishing;
– salt, particularly in the wheel arches
and underneath the body after driving in areas where the roads have
been gritted.
Remove any plant matter (resin, leaves,
etc.) from the vehicle regularly.
BODYWORK MAINTENANCE (2/2)
Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway).
Observe the vehicle stopping distances
when driving on gravelled surfaces to
prevent paint damage.
Repair, or have repaired quickly, areas
where the paint has been damaged, to
prevent corrosion spreading.
Remember to visit the body shop periodically in order to maintain your
anti-corrosion warranty. Refer to the
Maintenance Document.
If it is necessary to clean mechanical components, hinges, etc., spray
them with products approved by our
Technical Department to protect them
after they have been cleaned.
Vehicles with a matte paint
finish
This type of paint requires certain precautions.
Do not do the following
– use wax-based products (polishing);
– rub hard;
– wash the vehicle in a roller-type car
wash;
– wash the vehicle using a high-pressure device;
– attach stickers to the paintwork (risk
of leaving marks).
You should do the following
Wash the vehicle by hand using plenty
of water, using a soft cloth or a gentle
sponge.
Using a roller type car wash
Return the windscreen wiper stalk to
the Park position (refer to the information on the “Windscreen washer, wiper”
in Section 1). Check the mounting of
external accessories, additional lights
and mirrors, and ensure that the wiper
blades are secured with adhesive tape.
Remove the radio aerial mast if your
vehicle is fitted with this equipment.
Remember to remove the tape and refit
the antenna after washing.
Cleaning the headlights
As the headlights are made of plastic
“glass”, use a soft cloth or cotton wool
to clean them. If this does not clean
them properly, moisten the cloth with
soapy water, then wipe clean with a soft
damp cloth or cotton wool.
Finally, carefully dry off with a soft dry
cloth.
Cleaning products containing alcohol must not be used.
We have selected special products
to care for your vehicle and you can
obtain these from the manufacturer’s accessory outlets.
4.15
INTERIOR TRIM MAINTENANCE (1/2)
A well-maintained vehicle will last
longer. It is therefore recommended to
maintain the interior of the vehicle regularly.
A stain should always be dealt with
swiftly.
Whatever type of stain is on the trim,
use cold (or warm) soapy water with
natural soap.
Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used.
Use a soft cloth.
Glass instrument panel
(e.g. instrument panel, clock, exterior
temperature display, radio display, etc.)
Use a soft cloth (or cotton wool).
If this does not clean it properly, use a
soft cloth (or cotton wool) slightly moistened with soapy water and then wipe
clean with a soft damp cloth or cotton
wool.
Finally, carefully dry off with a soft dry
cloth.
Textiles (seats, door trim, etc)
Vacuum-clean the textiles regularly.
Liquid stain
Use soapy water.
Dab lightly (never rub) with a soft cloth,
rinse and remove the excess.
Solid or pasty stain
Cleaning products containing alcohol must not be used under any circumstances.
Carefully remove the excess solid or
pasty material immediately with a
spatula (working from the edges to the
centre to avoid spreading the stain).
Clean as for a liquid stain.
Seat belts
Special instructions for sweets or
chewing gum
Rinse and soak up the excess.
These must be kept clean.
Use products selected by our Technical
Department (Approved outlets) or
warm, soapy water and a sponge and
wipe with a dry cloth.
Detergents or dyes must not be used
under any circumstances.
Put an ice cube on the stain to solidify
it, then proceed as for a solid stain.
For further recommendations for
maintaining the interior, and/or for
any unsatisfactory results, please
see an authorised dealer.
4.16
INTERIOR TRIM MAINTENANCE (2/2)
Removal/replacing removable
equipment originally fitted in
the vehicle
If you need to remove equipment in
order to clean the passenger compartment (for example, mats), always
ensure that they are correctly refitted
and are the right way around (the driver’s mat should be fitted on the driver’s
side, etc.) and fit them with the components supplied with the equipment (for
example, the driver mat should always
be fixed using the pre-fitted mounting
components).
You should not:
You are strongly advised not to position objects such as deodorants,
scents, etc. near air vents, as this could
damage your dashboard trim.
With the vehicle stationary, ensure that
nothing will impede driving (anything
obstructing the pedals, heel wedged by
the mat, etc.).
You are strongly recommended not to use highpressure or spray cleaning
equipment inside the passenger compartment: use of such
equipment could impair the correct
functioning of the electrical or electronic components in the vehicle, or
have other detrimental effects.
4.17
4.18
Section 5: Practical advice
Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tyre inflation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools (jack, wheelbrace, etc.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel trims - wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing a wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tyres (tyre and wheel safety, use in winter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear lights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicator lights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior lights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RENAULT card: battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fitted audio equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wipers (replacing blades) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2
5.2
5.3
5.8
5.9
5.10
5.12
5.15
5.18
5.23
5.24
5.26
5.28
5.30
5.31
5.32
5.33
5.34
5.36
5.1
PUNCTURE, EMERGENCY SPARE WHEEL
In the event of a puncture,
depending on the vehicle,
you will have:
An emergency spare wheel or tyre inflation kit (refer to the information on the
following pages).
1
Emergency spare wheel
Special note:
The Tyre Pressure Monitor function
does not check the emergency spare
wheel (the wheel replaced by the emergency spare wheel disappears from the
instrument panel display).
Refer to the information on the “Tyre
pressure monitor” in Section 2.
This is located in the luggage compartment. To access it:
– open the tailgate;
– depending on the vehicle, unscrew
the anchorage points;
– fold back the luggage compartment
carpet using tab 1;
– unscrew the central mounting;
– remove the emergency spare wheel.
If the emergency spare wheel has been stored for several years, have it checked by your Dealer to ensure that it is
safe to use.
Vehicles fitted with an emergency spare wheel which is different to the four other wheels:
– Never fit more than one emergency spare wheel to the same vehicle.
– Replace the emergency spare wheel as soon as possible with a wheel identical to the original one.
– When this is fitted to the vehicle, which must only be a temporary measure, the driving speed must not exceed the speed
indicated on the label on the wheel.
– Fitting an emergency spare wheel may alter the way the vehicle usually runs. Avoid sudden acceleration or deceleration and
reduce your speed when cornering.
– If you need to use snow chains, fit the emergency spare wheel to the rear axle and check the tyre pressure.
5.2
TYRE INFLATION KIT (1/5)
B
A
Do not attempt to use the
inflation kit if the tyre has
been damaged as a result
of driving with a puncture.
The kit is only approved for
inflating the tyres of the vehicle originally equipped
with the kit.
You should therefore carefully check
the condition of the tyre sidewalls
before any operation.
It must never be used to inflate
the tyres of another vehicle, or any
other inflatable object (rubber ring,
rubber boat, etc.).
Driving with underinflated, flat or
punctured tyres can be dangerous
and may make the tyre impossible
to repair.
This repair is temporary
The kit repairs tyres when
tread A has been damaged by objects smaller
than 4 mm. It cannot repair
all types of puncture, such as cuts
larger than 4 mm, or cuts in tyre
sidewall B.
Ensure also that the wheel rim is in
good condition.
Do not pull out the foreign body
causing the puncture if it is still in
the tyre.
A tyre which has been punctured
should always be inspected (and repaired, where possible) as soon as
possible by a specialist.
When taking a tyre which has been
repaired using this kit to be replaced,
you must inform the specialist.
When driving, vibration may be felt
due to the presence of the repair
product injected into the tyre.
Avoid spillage on skin when handling the repair liquid bottle. If droplets do leak out, rinse them off with
plenty of water.
Keep the repair kit away from children.
Do not dispose of the empty bottle
in the countryside. Return it to your
approved dealer or to a recycling organisation.
The bottle has a limited service
life which is indicated on its label.
Check the expiry date.
Contact an approved dealer to replace the inflation tube and repair
product bottle.
5.3
TYRE INFLATION KIT (2/5)
1
2
3
C
4
Open the kit, remove caps 1 and 3 (the
cap must not be removed from the
bottle) then screw bottle 2 to its base 3.
5
Engine running, handbrake applied:
– unscrew the valve cap on the wheel
concerned and screw inflation
adapter 6 onto the valve;
6
8
7
Inflation kit C
Depending on the vehicle, in the event
of a puncture, use the kit located underneath the boot carpet.
Before using this kit, park
the vehicle at a sufficient
distance from traffic, switch
on the hazard warning
lights, apply the handbrake, ask all
passengers to leave the vehicle and
keep them away from traffic.
5.4
Depending on the vehicle, remove the
central partition in the storage compartment to access the inflation kit.
– adjust the pressure: to increase
it, continue inflating with the kit, to
reduce it, turn button 7 located on
the inflation adapter.
If a minimum pressure of 1.8 bar is
not reached after 15 minutes, repair
is not possible; do not drive the vehicle but contact an approved dealer.
– connect adapter 8 to the accessories
socket on the dashboard of the vehicle;
– press switch 5 to inflate the tyre to
the recommended pressure (check
the label affixed to the edge of the
driver’s door);
– after a maximum of 5 minutes, stop
inflating and read the pressure (on
pressure gauge 4);
Note: while the bottle is emptying
(approximately 30 seconds), pressure gauge 4 will briefly indicate a
pressure of 6 bar, then the pressure
will drop.
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation applying to the country you are in.
TYRE INFLATION KIT (3/5)
C
– affix driving recommendation label 9
to the dashboard where it can easily
be seen by the driver;
– store the kit;
9
8
Once the tyre is inflated correctly:
– stop using the kit;
– close the integrated cap on the bottle
again;
– disconnect adapter 8;
Nothing should be placed
around the driver’s feet
as such objects may slide
under the pedals during
sudden braking manoeuvres and
obstruct their use.
– after the first inflation procedure the
tyre will still be leaking; it is vital to
drive in order to plug the hole;
– start immediately and drive at between 12 and 36 mph (20 and
60 km/h) to distribute the product
evenly throughout the tyre, stopping
after a distance of 2 miles (3 kilometres) to check the pressure;
– If the pressure is above 1.3 bar but
lower than the recommended pressure, readjust it (refer to the label
affixed to the edge of the driver’s
door), otherwise contact an approved dealer: repair is not possible.
Note: after using the inflation kit, you
should visit an approved Dealer to replace the inflation hose and the bottle
of repair product.
Precautions when using the kit
The kit should not be operated for more
than 15 consecutive minutes.
Please be aware that a
poorly tightened or missing valve cap can make the
tyres less airtight and lead
to pressure loss.
Always use valve caps identical to
those fitted originally and tighten
them fully.
Following repair with the kit,
do not travel further than
120 miles (200 km). In addition, reduce your speed and
under no circumstances exceed
48 mph (80 km/h). The sticker,
which you must affix in a prominent
position on the dashboard, reminds
you of this.
Depending on the country or local
legislation, a tyre repaired with the
inflation kit may need to be replaced.
5.5
TYRE INFLATION KIT (4/5)
D
Engine running, handbrake applied:
– unroll the hose from the container;
10
17
– connect the compressor hose 12 to
the container’s inlet 17;
11
16
15
14
13
12
Inflation kit D
Depending on the vehicle, in the event
of a puncture, use the kit located in the
boot or underneath the luggage compartment carpet.
Before using this kit, park
the vehicle at a sufficient
distance from traffic, switch
on the hazard warning
lights, apply the handbrake, ask all
passengers to leave the vehicle and
keep them away from traffic.
5.6
– after a maximum of 15 minutes, stop
inflating and read the pressure (on
pressure gauge 14).
– depending on the vehicle, connect
the container 17 to the compressor
from the container recess 16;
Note: while the container is emptying (approximately 30 seconds), the
pressure gauge 14 will briefly indicate a pressure of up to 6 bar. The
pressure will then drop.
– unscrew the valve cap on the relevant wheel and screw on the container’s inflation adapter 10;
– adjust the pressure: to increase
it, continue inflation with the kit; to
reduce it, press button 15.
– adapter 11 must be connected to the
vehicle accessories socket;
If a minimum pressure of 1.8 bar is
not reached after 15 minutes, repair
is not possible; do not drive the vehicle but contact an approved dealer.
– press switch 13 to inflate the tyre to
the recommended pressure (please
refer to the information in the section
on “Tyre pressure”);
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation applying to the country you are in.
TYRE INFLATION KIT (5/5)
D
10
– Affix the driving recommendation
label to the dashboard where it can
easily be seen by the driver;
– Put the kit away.
– At the end of this initial inflation operation, air will still escape from the
tyre. You must drive a short distance
in order to seal the hole.
– Start immediately and drive at between 12 and 40 mph (20 and
60 km/h) in order to distribute the
product evenly in the tyre and, after
driving for 2 miles (3 km), stop and
check the pressure.
Once the tyre is correctly inflated,
remove the kit: slowly unscrew the inflation adapter 10 to prevent any repair
product from escaping and store the
container in plastic packaging to prevent the product from escaping.
Nothing should be placed
around the driver’s feet
as such objects may slide
under the pedals during
sudden braking manoeuvres and
obstruct their use.
– If the pressure is greater than 1.3 bar
but less than the recommended
pressure (refer to the label affixed to
the edge of the driver’s door), readjust it. Otherwise, please contact an
authorised dealer: the tyre cannot be
repaired.
Precautions when using the kit
The kit should not be operated for more
than 15 consecutive minutes.
Please be aware that a
poorly tightened or missing valve cap can make the
tyres less airtight and may
lead to pressure loss.
Always use valve caps identical to
those fitted originally and tighten
them fully.
Following repair with the kit,
do not travel further than
120 miles (200 km). In addition, reduce your speed and
under no circumstances exceed
48 mph (80 km/h). The sticker,
which you must affix in a prominent
position on the dashboard, reminds
you of this.
Depending on the country or local
legislation, a tyre repaired with the
inflation kit may need to be replaced.
5.7
TOOLS
Wheel brace 1
2
1
Locks or unlocks the wheel bolts and
tow eye 6.
Jack 2
7
3
4
5
6
The tools included in the tool kit depend
on the vehicle.
The tool kit is located in the luggage
compartment: lift the carpet.
Fold it correctly before refitting it in its
housing (ensure that the wheelbrace is
correctly positioned) 3.
Hubcap tool 4
This tool is used to remove the wheel
trims.
Wheel bolt guide 5
For tightening/loosening wheel bolts on
vehicles fitted with alloy wheels
Tow eye 6
Refer to the information on “Towing” in
Section 5.
Lever 7
This tightens or releases the tow eye 6.
5.8
Do not leave the tools unsecured inside the vehicle
as they may come loose
under braking. After use,
check that all the tools are correctly
clipped into the tool kit, then position
it correctly in its housing: there is a
risk of injury.
If wheel bolts are supplied in the
tool kit, only use these bolts for the
emergency spare wheel: refer to the
label affixed to the emergency spare
wheel.
The jack is designed for wheel
changing purposes only. Under no
circumstances should it be used for
carrying out repairs underneath the
vehicle or to gain access to the underside of the vehicle.
WHEEL TRIMS - WHEEL
1
A
2
C
B
D
Remove the wheel trim using hubcap
tool 1 (located in the tool kit) by engaging the hook in the opening near
valve 2.
To refit it, align it with valve 2. Push the
retaining hooks in fully, starting with
side A near the valve, followed by B
and C, finishing at D opposite the valve.
NB: if you are using anti-theft bolts,
please refer to the information on
“Changing a wheel”.
Do not leave the tools unsecured inside the vehicle
as they may come loose
under braking. After use,
check that all the tools are correctly
clipped into the tool kit, then position
it correctly in its housing: there is a
risk of injury.
If wheel bolts are supplied in the
tool kit, only use these bolts for the
emergency spare wheel: refer to the
label affixed to the emergency spare
wheel.
The jack is designed for wheel
changing purposes only. Under no
circumstances should it be used for
carrying out repairs underneath the
vehicle or to gain access to the underside of the vehicle.
5.9
CHANGING A WHEEL (1/2)
3
Vehicles equipped with a jack
and wheelbrace
If necessary, remove the wheel trim.
1
Use the wheelbrace 3 to slacken off the
wheel bolts. Position it so as to be able
to push from above.
2
Offer up the jack 4 horizontally; the jack
head must be lined up with jacking
point 1 located on the underside of the
sill, closest to the wheel concerned, as
shown by arrow 2.
Start cranking the jack up by hand to
align the base plate (which should be
pushed slightly under the vehicle).
Turn the wheelbrace until the wheel lifts
off the ground.
4
Switch on the hazard warning lights.
Keep the vehicle away from
traffic and on a level surface where it will not slip (if necessary, place a solid support under the
jack base).
Apply the parking brake and engage
a gear (first or reverse, or P for automatic transmissions).
Ask all the passengers to leave the
vehicle and keep them away from
traffic.
5.10
If the vehicle is not equipped with a
jack or wheelbrace, you can obtain
these from your approved dealer.
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation applying to the country you are in.
To prevent any risk of injury
or damage to the vehicle,
only crank the jack until the
wheel you are replacing is
a maximum of 3 centimetres off the
ground.
CHANGING A WHEEL (2/2)
Undo the bolts and take off the wheel.
Fit the emergency spare wheel onto
the hub and rotate it until the mounting
holes in the wheel coincide with those
of the hub.
If bolts are supplied with the emergency
spare wheel, only use these bolts for
the emergency spare wheel. Tighten
the bolts, checking that the wheel is
correctly positioned on its hub and
lower the jack.
With the wheel on the ground, tighten
the bolts fully and have the tightness
of the bolts checked (tightening torque:
110 N.m) and the emergency spare
wheel pressure checked as soon as
possible.
Anti-theft bolt
If you use anti-theft bolts, fit these
nearest the valve (wheel trim may
not be able to fit).
If you have a puncture, replace the wheel as soon as
possible.
A tyre which has been punctured should always be inspected
(and repaired, where possible) by a
specialist.
5.11
TYRES (1/3)
Tyre and wheel safety
The tyres are the only contact between
the vehicle and the road, so it is essential to keep them in good condition.
2
You must make sure that your tyres
conform to local road traffic regulations.
1
When the tyre tread has been worn to
the level of the wear indicators, they
become visible 2: it is then necessary
to replace your tyres because the tread
rubber is no more than 1.6 mm deep,
resulting in poor roadholding on wet
roads.
An overloaded vehicle, long journeys
by motorway, particularly in very hot
weather, or continual driving on poorly
surfaced minor roads will lead to more
rapid tyre wear and affect safety.
Maintaining the tyres
When they need to be replaced, only tyres of the
same make, size, type and
profile should be used.
Tyres fitted to the vehicle should
either be identical to those fitted
originally or conform to those
recommended by your approved
dealer.
5.12
The tyres must be in good condition
and the tread form must have sufficient
depth; tyres approved by our Technical
Department have wear warning strips 1
that are indicators moulded into the
tread at several points.
Incidents which occur when
driving, such as striking the
kerb, may damage the tyres
and wheel rims, and could
also lead to misalignment of the
front or rear axle geometry. In this
case, have the condition of these
checked by an approved dealer.
TYRES (2/3)
Tyre pressures
Adhere to the tyre pressures (including
the emergency spare wheel). The tyre
pressures should be checked at least
once a month and additionally before
any long journey (refer to the label affixed to the edge of the driver’s door).
Pressures should be checked when the
tyres are cold; ignore higher pressures
which may be reached in hot weather
or following a fast journey.
If tyre pressures cannot be checked
when the tyres are cold, the normal
pressures must be increased by 0.2 to
0.3 bar (or 3 PSI).
Never deflate a hot tyre.
Incorrect tyre pressures
lead to abnormal tyre wear
and unusually hot running.
These are factors which
may seriously affect safety and lead
to:
Special note
Depending on the vehicle, there may
be an adapter which needs to be positioned on the valve before air is added.
Fitting new tyres
For safety reasons, this operation must be carried out
by a specialist.
Fitting different tyres may
change your vehicle as follows:
– It may mean that your vehicle no
longer conforms to current regulations;
– It may change the way it handles
when cornering;
– It may cause the steering to be
heavy;
– It may affect the use of snow
chains.
– poor road holding,
– risk of bursting or tread separation.
The pressure depends on the load
and the speed of use. Adjust the
pressure according to the conditions of use (refer to the label affixed
to the edge of the driver’s door).
Please be aware that a
poorly tightened or missing valve cap can make the
tyres less airtight and lead
to pressure loss.
Emergency spare wheel
Refer to the information on the
“Emergency spare wheel” and instructions on “Changing a wheel” in
Section 5.
Always use valve caps identical to
those fitted originally and tighten
them fully.
5.13
TYRES (3/3)
Use in winter
Studded tyres
Chains
This type of equipment may only be
used for a limited period and as laid
down by local legislation. It is necessary to observe the speed specified by
current legislation.
For safety reasons, fitting snow
chains to the rear axle is strictly forbidden.
Chains cannot be fitted to tyres which
are larger than those originally fitted to
the vehicle.
These tyres must, at a minimum, be
fitted to the two front wheels.
Snow or Winter tyres
We would recommend that these be
fitted to all four wheels to ensure that
your vehicle retains maximum adhesion.
Warning: These tyres sometimes have
a specific direction of rotation and a
maximum speed index which may be
lower than the maximum speed of your
vehicle.
In all cases, we would recommend
that you contact an approved dealer
who will be able to advise you on
the choice of equipment which is
most suitable for your vehicle.
Changing a wheel
18” wheels cannot be
fitted with chains.
If you wish to fit snow
chains, you must use special equipment.
Consult an approved Dealer.
5.14
As the tyre pressure monitor may take several minutes following driving to correctly determine the positions of the
wheels and the pressure values,
check the tyre pressures following
any operation.
FRONT HEADLIGHTS: changing bulbs (1/3)
A
1
After opening the bonnet, pull tool A upwards. Remove the two screws 1 from
the headlight using the A tool.
Pull the headlight forwards, sliding it in
its rails up to the end stop.
After refitting the light, tighten the
screws 1 and reposition the tool A correctly in its housing.
Direction indicator lights
B
C
D
E
Dipped beams
Halogen dipped beam headlight
Unlock the two springs D, remove
the cover, then unclip the spring 3 to
remove the bulb 4.
Bulb type: H7.
It is essential to use anti U.V. 55W
bulbs so as not to damage the plastic
on the headlights.
B
3
4
5
6
Do not touch the bulb glass. Hold it
by its base.
When the bulb has been changed,
make sure you refit the cover correctly.
Discharge bulb dipped beam
headlight
Bulb type: D1S.
Rotate the bulb holder B to unlock it.
Bulb type: PY21W.
Deactivate the Stop and
Start function for any operation performed in the engine
compartment.
2
dealer.
Due to the danger involved
in handling high-voltage devices, this type of bulb must
be replaced by an approved
5.15
FRONT HEADLIGHTS: changing bulbs (2/3)
B
C
D
E
B
2
3
4
5
6
Daytime running light
Front side light
Remove the cover C, unlock the bulb
holder 2 by rotating it.
Bulb type: P21W.
Remove the cover E and pull the bulb
holder 6.
Main beam headlight
Remove the cover E, press the bulb
holder 5 downwards to unlock it.
To comply with current legislation,
or as a precaution, you can obtain
an emergency kit from an approved
dealer containing a set of spare
bulbs and fuses.
Bulb type: W5W.
The bulbs are under pressure and can break when
replaced.
Risk of injury.
Bulb type: H7.
The engine may be hot
when carrying out operations in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
5.16
FRONT HEADLIGHTS: changing bulbs (3/3)
Additional lights
If you wish to fit fog lights or long range
headlights to your vehicle, consult an
approved Dealer.
7
8
Daytime running lights 7
Please see an authorised dealer.
Front fog lights 8
The front bumper needs to be removed;
consult an approved Dealer.
The bulbs are under pressure and can break when
replaced.
Any operation on (or modification to) the electrical
system must be performed
by an approved dealer
since an incorrect connection might
damage the electrical equipment
(harness, components and in particular the alternator). In addition, your
Dealer has all the parts required for
fitting these units.
Risk of injury.
5.17
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (1/6)
5
A
2
3
1
B
6
4
Five-door versions
Direction indicator lights/brake and
side lights
– Unclip the cover to access nuts 1
and 2;
– unscrew nut 2 without removing it
completely;
The bulbs are under pressure and can break when
replaced.
Risk of injury.
5.18
– loosen nut 1, press down on it to
release the front of the light (movement A) then remove the nut;
– from the outside, pull the light towards you (movement B);
– remove the bulb holder 3 by releasing the clips 4.
Direction indicator lights 5
Bulb type: PY21W.
Side light and brake light 6
Bulb type: P21/5W.
Refitting
To refit, proceed in the reverse order,
taking care not to damage the wiring.
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (2/6)
9
10
8
11
7
Five-door versions
(continued)
Fog lights/side lights and reversing
lights
– Lower the tailgate, then pull light 9
towards the rear to release it.
Reversing light 10
– Unscrew the bulb holder for the bulb
concerned.
Fog light/side light 11
Bulb type: W16W.
Bulb type: P21/4W.
– From the luggage compartment,
unclip flap 7, then remove the
bolts 8.
5.19
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (3/6)
13
14
12
17
16
15
Three-door versions
– Unclip the access flap;
16 Side light/stop light
Bulb type: P21/5W.
– unscrew nuts 12 and 13;
17 Direction indicator light
– from the outside, remove bolt 14,
then pull on the light;
18 Reversing light
– remove the bulb holder by releasing
the clips 15;
18
Bulb type: PY21W.
Bulb type: P21W.
Rear fog light
Undo bulb holder 19, turning it towards
the centre of the vehicle by accessing it
from underneath.
The bulbs are under pressure and can break when
replaced.
Risk of injury.
5.20
Bulb type: P21W.
19
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (4/6)
21
22
23
C
24
20
Sport tourer Versions
Side lights/reversing lights and fog
lights
– From the luggage compartment,
unclip flap 20 (movement C), then
remove the bolts .
– Lower the tailgate, then pull light 21
towards the rear to release it.
– Turn the bulb holder of the bulb concerned a quarter of a turn.
Side light 22
Bulb type: W5W.
Reversing light 23
Bulb type: P21W.
Fog light 24
Bulb type: H21W.
Refitting
To refit, proceed in the reverse order,
taking care not to damage the wiring.
The bulbs are under pressure and can break when
replaced.
Risk of injury.
5.21
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (5/6)
26
28
27
25
Estate versions
Side light and brake light 28
(continued)
Bulb type: P21/5W.
Brake and side lights/direction
indicator lights
Direction indicator lights 29
– Unclip covers 25 to access the nuts;
– unscrew the 2 nuts;
– from the outside, pull the light towards you;
– remove the bulb holder 27 by releasing the clips 26.
5.22
Bulb type: PY21W.
29
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (6/6)
31
32
30
D
22
23
33
High level brake light 30
Number plate lights 32
Indicator lights 33
Consult an approved Dealer.
– Unclip light 32 by pressing tab 31;
– Unclip indicator light 33 (using a
flat-blade screwdriver type tool positioned at D to move the indicator
light towards the front of the vehicle);
– remove the light cover to gain access
to the bulb.
Bulb type: W5W.
– turn the bulb holder a quarter of a
turn and take out the bulb.
Bulb type: W5W.
The bulbs are under pressure and can break when
replaced.
Risk of injury.
5.23
INTERIOR LIGHTING: changing bulbs (1/2)
1
B
2
A
3
4
Courtesy light
Door lights
Glove box light
– Position the 3 switches in the central
position;
Unclip light 2 (using a flat-blade screwdriver or similar).
Open the access cover 3, you can then
unclip the bulb holder more easily 4.
– move the courtesy light backwards
(movement A) then tilt the front
downwards (movement B);
Turn the bulb holder a quarter of a turn
and take out the bulb.
Bulb type: C5W.
– when removing the courtesy light,
ensure that you do not pull the electrical wires;
Bulb type: W5W.
– unclip the lens 1;
Note: to remove the defective bulb, you
can use a flat-blade screwdriver or similar.
Bulb type: W5W.
The bulbs are under pressure and can break when
replaced.
Risk of injury.
5.24
INTERIOR LIGHTING: changing bulbs (2/2)
6
7
8
5
Luggage compartment light
Disconnect the light.
Unclip the light at 5 using a flat-blade
screwdriver or similar.
Press tab 6 to release lens 8 and
access bulb 7.
Bulb type: W5W.
The bulbs are under pressure and can break when
replaced.
Risk of injury.
5.25
FUSES (1/2)
1
A
B
Fuse box
Tweezers 1
If any electrical component does not
work, check the condition of the fuses.
Remove the fuse using tweezers 1, located at the back of flap A or B.
Unclip cover A or B (depending on vehicle).
In accordance with local legislation
or as a precautionary measure:
Obtain an emergency kit containing
a set of spare bulbs and fuses from
an approved Dealer.
5.26
Check the fuse in question
and replace it, if necessary, by a fuse of the same
rating.
If a fuse is fitted where the rating is
too high, it may cause the electrical
circuit to overheat (risk of fire) in the
event of an item of equipment using
an excessive amount of current.
To remove the fuse from the tweezers,
slide the fuse to the side.
It is not advisable to use the free fuse
locations.
FUSES (2/2)
3
7
10
14
4
8
11
15
1
5
9
12
16
2
6
13
17
C
18
19
Allocation of fuses
(the presence of certain fuses depends
on the vehicle equipment level)
1 Electronic parking brake;
2 Brake lights;
3 Automatic door locking;
4 Driver’s electric window;
5 Passenger compartment unit;
6 Direction indicator lights;
7 Navigation system;
8 Interior rear-view mirror;
9 Rear screen wiper;
10 and 11 Rear electric windows;
12 ABS/ESC ;
13 Passenger electric window;
Some accessories are protected by
fuses located in the engine compartment in fuse box C.
However, because of their reduced accessibility, we advise you to have your
fuses replaced by an approved Dealer.
14 Windscreen washer;
15 Heated door mirrors;
16 Radio;
17 Luggage compartment accessories
socket;
18 Rear seat accessories socket;
19 Cigarette lighter.
5.27
BATTERY: troubleshooting (1/2)
To avoid all risk of sparks:
Connecting a battery charger
– Ensure that any electrical consumers
(courtesy lights, etc.) are switched
off before disconnecting or reconnecting the battery.
The battery charger must be compatible with a battery with nominal
voltage of 12 volts.
– When charging, stop the charger
before connecting or disconnecting
the battery.
Do not disconnect the battery when the
engine is running. Follow the instructions given by the manufacturer of
the battery charger you are using.
– Do not place metal objects on the
battery to avoid creating a short circuit between the terminals.
– Always wait at least one minute after
the engine has been switched off
before disconnecting a battery.
Handle the battery with care
as it contains sulphuric acid,
which must not come into
contact with eyes or skin. If
it does, wash the affected area with
plenty of cold water. If necessary,
consult a doctor.
– Make sure that you reconnect the
battery terminals after refitting.
Special procedures may be
required to charge some
batteries. Contact your approved dealer.
Avoid all risk of sparks which may
cause an immediate explosion, and
charge the battery in a well-ventilated area. Risk of serious injury.
Deactivate the Stop and
Start function for any operation performed in the engine
compartment.
5.28
Ensure that naked flames, red hot
objects and sparks do not come into
contact with the battery as there is a
risk of explosion.
The engine may be hot when carrying out operations in close proximity. In addition, the engine cooling
fan can come on at any moment.
Risk of injury.
BATTERY: troubleshooting (2/2)
Starting the vehicle using the
battery from another vehicle
1
If you have to use the battery from another vehicle to start, obtain suitable
jump leads (with a large cross section)
from an approved dealer or, if you already have jump leads, ensure that
they are in perfect condition.
The two batteries must have an identical nominal voltage of 12 volts. The
battery supplying the current should
have a capacity (amp-hours, Ah) which
is at least the same as that of the discharged battery.
Ensure that there is no risk of contact
between the two vehicles (risk of short
circuiting when the positive terminals
are connected) and that the discharged
battery is properly connected. Switch
off your vehicle ignition.
Start the engine of the vehicle supplying the current and run it at an intermediate engine speed.
1
4
4
B
A
1
2
3
Connect the positive cable A to the
support 1 on the (+) terminal, then to
the (+) terminal 2 of the battery supplying the current.
Connect the negative cable B to the (–)
terminal 3 of the battery supplying the
current and then to the (–) terminal 4 of
the discharged battery.
Start the engine, and as soon as it starts
running, disconnect cables A and B in
reverse order ( 4 - 3 - 2 - 1 ).
Check that there is no contact between leads A and B
and that the positive lead A
is not touching any metal
parts on the vehicle supplying the
current.
Risk of injury and/or damage to the
vehicle.
5.29
RENAULT CARD: battery
2
A
B
4
1
Replacing the battery
When the message “Keycard battery
low” appears on the instrument panel,
replace the RENAULT card battery,
press button 1 pulling on emergency
key 2, then unclip the cover 3 using
tab 4.
Remove the battery by pressing on one
side (movement A) and by lifting the
other (movement B) then replace it, ensuring the polarity and model, shown
on cover 3 are respected.
3
When refitting, proceed in the reverse
order, then press one of the buttons on
the card four times, close to the vehicle:
the next time the vehicle is started, the
message will disappear.
Note: it is not advisable to touch the
electronic circuit or contacts on the
RENAULT card when replacing the battery.
Check that the cover is clipped shut.
The batteries are available from approved Dealers, and their service life approximately two years. Check that there is no dye on the battery: risk of an incorrect
electrical contact.
5.30
Operating faults
If the battery is too weak to ensure correct operation, you may start (insert the
RENAULT card in the card reader) and
lock/unlock the vehicle (refer to the information on “Locking/unlocking the
doors” in Section 1).
Do not throw away your
used batteries; give them to
an organisation responsible
for collecting and recycling
batteries.
FITTING A RADIO
2
1
3
If your vehicle is not fitted with an audio
system, one can be fitted and locations
have been provided for:
– the radio 1;
– tweeter speakers 2;
– bass speakers 3.
To install any equipment, please consult an approved dealer.
Radio location 1
Unclip the blanking cover. The aerial, +
and – supply and speaker wire connections are located behind it.
– In all cases, it is very important to follow the manufacturer’s instructions carefully.
– The specifications of the brackets and wires (available from our network) vary
depending on the equipment level of your vehicle and the type of radio.
Consult an approved Dealer to find out the correct part number.
– No work may be carried out on the vehicle’s electrical or radio circuits, except
by approved dealers: an incorrectly connected system may result in damage
being caused to the electrical equipment and/or the components connected to
it.
5.31
ACCESSORIES
Electrical and electronic accessories
Before installing this type of accessory, make sure it is compatible with your vehicle. You can get advice from an authorised dealer.
Connect accessories with a maximum power of 120 watts only. Fire hazard.
No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorrectly connected
system may result in damage being caused to the electrical equipment and/or the components connected to it.
If the vehicle is fitted with any aftermarket electrical equipment, make sure that the installation is correctly protected by a fuse.
Establish the rating and position of this fuse.
Use of transmission/receiving devices (telephones, CB equipment etc.).
Telephones and CB equipment with integrated aerials may cause interference to the electronic systems originally fitted to the
vehicle: it is advisable only to use equipment with an external aerial. Furthermore, we remind you of the need to conform
to the legislation in force concerning the use of such equipment.
Fitting after-market accessories
If you wish to install accessories on the vehicle: please contact an authorised dealer. Also, to ensure the correct operation of
your vehicle, and to avoid any risk to your safety, we recommend that you use only accessories specifically designed for your
vehicle, which are the only accessories for which the manufacturer will provide a warranty.
If you are using an anti-theft device, only attach it to the brake pedal.
Obstructions to the driver
On the driver’s side, only use mats suitable for the vehicle, attached with the pre-fitted components, and check the fitting regularly. Do not lay one mat on top of another. There is a risk of wedging the pedals
5.32
WINDSCREEN WIPER BLADES
1
B
A
4
2
C
5
3
6
Replacing windscreen wiper
blades 1
Rear screen wiper blade 4
With the ignition on and engine
switched off, lower the windscreen
wiper stalk completely: they stop
slightly away from the bonnet.
Lift wiper arm 3, pull tab 2 (movement A) and push the blade upwards.
– pivot blade 4 until some resistance is
met (movement C);
To refit
Slide the blade along the arm until it
clips on. Make sure that the blade is
correctly locked in position. Return the
windscreen wiper stalk to the park position.
– Lift wiper arm 6;
– depending on the vehicle, press
tab 5, then remove the blade by pulling it (movement B).
To refit
To refit the wiper blade, proceed in reverse order to removal. Make sure that
the blade is correctly locked in position.
Check the condition of the wiper
blades. You are responsible for their
service life:
– clean the blades, windscreen and
rear screen regularly with soapy
water;
– do not use them when the windscreen or rear screen are dry;
– free them from the windscreen or
rear screen when they have not
been used for a long time.
– In frosty weather, make
sure that the wiper blades
are not stuck by ice (to
avoid the risk of the motor
overheating).
– Check the condition of the wiper
blades.
Replace the wiper blades as soon
as they begin to lose efficiency
(approximately once a year).
Whilst changing the blade, take care
not to drop the arm onto the window
after it has been removed as this
may break the window.
5.33
TOWING: breakdown (1/2)
Before towing, unlock the steering
column: with the clutch depressed,
engage first gear (lever in position N
or R for vehicles with automatic transmissions), insert the RENAULT card in
the card reader then press the engine
start button for two seconds.
The speed specified by current legislation for towing must always be observed. If your vehicle is the towing
vehicle, do not exceed the maximum
towing weight for your vehicle (refer to
the information on “Weights” in Section
6).
Reposition the lever to neutral (position
N for vehicles fitted with an automatic
gearbox).
Towing a vehicle with an
automatic gearbox
The steering column unlocks, the vehicle’s accessory functions are powered, and you can use the vehicle lights
(brake lights, hazard warning lights,
etc.). At night, the vehicle must be lit.
Once you have finished towing, press
the engine start button twice (risk of
running down the battery).
Do not remove the
RENAULT card from the
reader when the vehicle is
being towed.
5.34
1
2
With the engine switched off, the transmission is no longer lubricated. It is
preferable to tow this type of vehicle on
a trailer or tow it with the front wheels
off the ground.
Under exceptional circumstances,
you may tow the vehicle with all four
wheels on the ground, only going forward, with the gear lever in the N position, and for a distance not exceeding
50 miles (80 km).
If the lever is stuck in P,
even though you are depressing the brake pedal,
the lever can be released
manually. To do this, insert a rigid
rod in the hole 2, press the rod and
unlocking button 1 located on the
lever simultaneously.
TOWING: breakdown (2/2)
– Use a rigid towing bar.
If a rope or cable is used
(where the law allows this),
the vehicle being towed
must be able to brake.
3
6
4
5
Only use the front 3 and rear 6 towing
points
(never use the drive shafts or any other
part of the vehicle). These towing points
may only be used for towing: never use
them for lifting the vehicle directly or indirectly.
– A vehicle must not be towed if it is
not fit to be driven.
7
4
Access to towing points
Unclip cover 5 or 7 by sliding a flat tool
(or the key integrated in the RENAULT
card) under the cover.
– Avoid accelerating or braking
suddenly when towing, as this
may result in damage being
caused to the vehicle.
– When towing a vehicle, it is advisable not to exceed 30 mph
(50 km/h).
– Do not push the vehicle if the
steering column is locked.
Tighten the tow eye 4 fully: as much
as possible by hand at first, then finish
tightening it using the wheelbrace or,
depending on the vehicle, the lever.
Use only towing hitch 4 and the wheelbrace or the lever located under the
luggage compartment carpet in the tool
kit (please refer to the information on
the “Tool kit” in Section 5).
When the engine is
stopped, steering and braking assistance are not operational.
Do not leave the tools unsecured inside the vehicle as
they may come loose under
braking.
5.35
OPERATING FAULTS (1/6)
The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact
an approved Dealer as soon as possible.
Using the RENAULT card
POSSIBLE CAUSES
WHAT TO DO
The RENAULT card does not lock or
unlock the doors.
Card battery is flat.
Replace the battery. You can still lock/
unlock and start your vehicle (refer to the information on “Locking, unlocking the opening elements” in Section 1 and “Starting,
stopping the engine” in Section 2).
Use of appliances operating on the
same frequency as the card (mobile
phone, etc.).
Stop using the equipment or use the integrated key (refer to the information on
“Locking, unlocking the opening elements”
in Section 1).
Vehicle located in a high electromagnetic radiation zone.
Use the key integrated in the card (refer to
the information on “Locking, unlocking the
opening elements” in Section 1).
Vehicle battery flat.
The vehicle is started.
5.36
With the engine running, the card’s locking/
unlocking device is blocked. Turn off the ignition.
OPERATING FAULTS (2/6)
The starter is activated
POSSIBLE CAUSES
WHAT TO DO
The instrument panel indicator lights Battery terminals not tight, bat- Retighten or reconnect the terminals, or clean them
are weak or fail to light up and the tery terminals disconnected or if they are oxidised.
starter does not turn.
oxidised.
Discharged battery or not opera- Connect another battery to the faulty battery. Refer to
tional.
information on “Battery: troubleshooting” in Section
5 or replace the battery if necessary.
Do not push the vehicle if the steering column is
locked.
Faulty circuit.
The engine will not start.
Consult an approved dealer.
Starting conditions are not ful- Please refer to the information on “Starting, stopping
filled.
the engine” in Section 2.
The RENAULT “hands-free” card Insert the card in the card reader in order to start
does not work.
the engine.
Please refer to the information on “Starting, stopping
the engine” in Section 2.
The engine cannot be switched off.
The steering column remains locked.
Card not detected.
Insert the card in card reader.
Electronic fault.
Press the starter button quickly five times. The
engine can be restarted by pressing on the clutch
pedal if the Stop and Start function is activated.
Steering wheel locked.
Move the steering wheel while pressing the engine
start button (please refer to Section 2 “Starting, stopping the engine”).
Faulty circuit.
Consult an approved dealer.
5.37
OPERATING FAULTS (3/6)
On the road
POSSIBLE CAUSES
WHAT TO DO
Vibrations.
Tyres not inflated to correct pressures, incorrectly balanced or damaged.
Check the tyre pressures: if this is not the
problem, have them checked by an approved Dealer.
White smoke from the exhaust.
In the diesel version, this is necessarily a fault. Smoke may be caused by
particle filter regeneration.
Please refer to the information on “Special
features of diesel versions” in Section 2.
Smoke under the bonnet.
Short-circuit or cooling system leak.
Stop, switch off the ignition, stand away
from the vehicle and contact an approved
dealer.
while cornering or braking
The level is too low.
Top up the engine oil level (refer to the information on “Engine oil level: topping up,
filling” in Section 4).
is slow to go out or remains lit
under acceleration
Loss of oil pressure.
Stop the vehicle and contact an approved
Dealer.
The oil pressure warning light comes
on:
5.38
OPERATING FAULTS (4/6)
On the road
POSSIBLE CAUSES
WHAT TO DO
Steering becomes heavy.
Assistance overheating.
Consult an approved dealer.
The engine is overheating. The coolant temperature indicator is in the
warning zone and warning light
® comes on.
Engine cooling fan not working.
Stop the vehicle, switch off the engine and
contact an approved dealer.
Coolant leaks.
Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an
approved dealer as soon as possible.
Mechanical fault: damaged cylinder
head gasket.
Stop the engine.
Contact an approved dealer.
Coolant boiling in the coolant reservoir.
Radiator: If there is a significant lack of coolant, remember that it must never be topped up using cold coolant while
the engine is very warm. After any procedure on the vehicle which has involved even partial draining of the cooling
system, it must be refilled with a new mixture prepared in the correct proportions. Reminder: only products approved
by our Technical Department may be used for this purpose.
5.39
OPERATING FAULTS (5/6)
Electrical equipment
POSSIBLE CAUSES
WHAT TO DO
The wipers do not work.
Wiper blades stuck.
Free the blades before using the wipers.
Faulty electrical circuit.
Consult an approved dealer.
Fuse damaged.
Replace the fuse, refer to the information
on “Fuses”.
The wiper does not stop.
Faulty electrical controls.
Consult an approved dealer.
Direction indicators flashing more
quickly.
Blown bulb.
See information on “Headlights: changing
bulbs” or “Rear and side lights: changing
bulbs”.
The direction indicators do not work.
Faulty electrical circuit or control.
Consult an approved dealer.
Fuse damaged.
Replace the fuse, refer to the information
on “Fuses”.
Faulty electrical circuit or control.
Consult an approved dealer.
Fuse damaged.
Replace the fuse, refer to the information
on “Fuses”.
The lights do not come on or go off.
5.40
OPERATING FAULTS (6/6)
Electrical equipment
POSSIBLE CAUSES
Traces of condensation in the lights.
Traces of condensation may be a natural phenomenon caused by variations in temperature.
WHAT TO DO
In this case, the traces will disappear
slowly once the lights are switched
on.
The front seat belt reminder light
comes on when the seat belts are
fastened.
An object is stuck between the floor
and the seat and is disrupting the operation of the sensor.
Remove all objects from underneath the
front seats.
5.41
5.42
Section 6: Technical specifications
Vehicle identification plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine identification plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Towing weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement parts and repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Anti-corrosion check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2
6.3
6.6
6.9
6.10
6.10
6.11
6.12
6.18
6.1
VEHICLE IDENTIFICATION PLATES
A
A
10
9
1
2
3
4
5
6
7
8
The information shown on the vehicle identification plate should be
quoted on all correspondence or
orders.
The presence and location of the information depends on the vehicle.
B
6.2
Vehicle identification plate A
1 Manufacturer name.
2 EC design number or approval
number.
3 Identification number.
Depending on the vehicle, this
information is also given on
marking B.
4 MAM (Maximum Authorised Mass)
for front axle.
5 GTW (Gross train weight: vehicle
fully loaded, with trailer).
6 MPAW (Maximim Permissible
Weight) for front axle.
7 MPAW on rear axle.
8 Reserved for related or additional
entries.
9 Diesel exhaust emissions.
10 Paint reference (colour code).
ENGINE IDENTIFICATION PLATES (1/3)
A
1
2
A
3
A
Quote the information on the identification plate or label A in all correspondence or when ordering parts.
(Location varies depending on engine)
1 Engine type.
2 Engine suffix.
3 Engine number.
A
6.3
ENGINE IDENTIFICATION PLATES (2/3)
A
A
A
6.4
ENGINE IDENTIFICATION PLATES (3/3)
A
1
2
A
3
A
A
Quote the information on the identification plate or label A in all correspondence or when ordering parts.
(Location varies depending on engine)
1 Engine type.
2 Engine suffix.
3 Engine number.
A
6.5
DIMENSIONS (in metres) (1/3)
Three door version
0.862
2.640
0.797
1.546
4.299
1.423*
1.547
1.785
*
Unladen
6.6
DIMENSIONS (in metres) (2/3)
Five door version
0.862
2.641
0.792
1.546
4.292
1.471*
1.547
1.808
*
Unladen
6.7
DIMENSIONS (in metres) (3/3)
Sport tourer versions
0.862
2.703
0.994
1.546
4.558
1.461*
1.547
1.766
*
Unladen
6.8
ENGINE SPECIFICATIONS
Versions
1.2 TCe
1.4 TCe
1.6 16V
2.0 16V
2.0 T
1.5 dCi
1.6 dCi
1.9 dCi
2.0 dCi
Engine type
(see engine plate)
H5F
Turbo
H4J
Turbo
K4M
M4R
F4R
Turbo
K9K
R9M
F9Q
M9R
Cubic capacity (cc)
1 197
1,395
1,598
1,998
1,998
1,461
1 598
1,870
1,995
Type of fuel
Octane Rating
Spark plugs
It is essential that you use unleaded petrol of the octane
rating stated on the label inside the fuel filler flap.
If not available, for a limited time only, use unleaded fuel:
– with an octane rating of 91 for a label showing 95 or
98;
– with an octane rating of 87 for a label showing 91, 95
or 98.
Diesel
The label located in the fuel filler
flap indicates authorised fuels.
Only use the spark plugs specified for your vehicle’s
engine.
The type should be marked on a label affixed inside the
engine compartment. If it is not then contact your approved dealer.
Fitting spark plugs which are not to specification may
damage the engine.
6.9
WEIGHTS (in kg)
The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult
your approved Dealer.
Five door
Maximum permissible all-up weight (MMAC)
Gross Train Weight (MTR)
Braked trailer weight*
Estate
Weights are indicated on the vehicle identification plate (refer to
the information on “Vehicle identification plates” in Section 6)
found by calculating: MTR - MMAC
Unbraked trailer weight*
635
Permissible nose weight*
75
Permissible load on the roof with the carrying device
Three door
80 kg (including the carrying device)
Prohibited
* Towing weight (towing a caravan, boat, etc.)
Towing is prohibited when the MTR - MMAC calculation is equal to zero, or when the MTR is equal to zero (or is not listed) on the
identification plate.
– It is important to comply with the towing weights, governed by local legislation in each country and, in particular, laid down in
the Road Traffic Regulations. Contact an approved Dealer about any towing equipment.
– When towing, under no circumstances may the total train weight (vehicle + trailer) be exceeded. However the following is
permitted:
– rear axle MMTA exceeded by no more than 15%,
– maximum MMAC exceeded by no more than 10% or 100 kg (whichever is reached first).
In either case, the maximum speed of the vehicle and trailer must not exceed 60 mph (100 km/h) and the tyre pressures must
be increased by 0.2 bar (3 PSI).
– The engine output and climbing capability are reduced with altitude. We recommend that the maximum load be reduced by 10%
at an altitude of 1,000 metres and by an additional 10% for each 1,000 metres thereafter.
Load transfer Sport Tourer versions
If the Maximum Authorised Mass of the vehicle has not been reached, up to 200 kg can be transferred to the braked trailer, within
the limits of the Gross Train Weight.
6.10
REPLACEMENT PARTS AND REPAIRS
Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same
level of quality as the parts fitted originally.
If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out
within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the
repair order.
6.11
SERVICE SHEETS (1/6)
VIN: ..................................................................................
Date:
Miles (km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anticorrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Anticorrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Anticorrosion check:
OK □
Not OK* □
*See specific page
6.12
□
Stamp
SERVICE SHEETS (2/6)
VIN: ..................................................................................
Date:
Miles (km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anticorrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Anticorrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Stamp
□
Anticorrosion check:
OK □
Not OK* □
*See specific page
6.13
SERVICE SHEETS (3/6)
VIN: ..................................................................................
Date:
Miles (km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anticorrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Anticorrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Anticorrosion check:
OK □
Not OK* □
*See specific page
6.14
□
Stamp
SERVICE SHEETS (4/6)
VIN: ..................................................................................
Date:
Miles (km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anticorrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Anticorrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Stamp
□
Anticorrosion check:
OK □
Not OK* □
*See specific page
6.15
SERVICE SHEETS (5/6)
VIN: ..................................................................................
Date:
Miles (km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anticorrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Anticorrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Anticorrosion check:
OK □
Not OK* □
*See specific page
6.16
□
Stamp
SERVICE SHEETS (6/6)
VIN: ..................................................................................
Date:
Miles (km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anticorrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Anticorrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (km):
Type of operation:
Service
□
.......................................
Stamp
□
Anticorrosion check:
OK □
Not OK* □
*See specific page
6.17
ANTICORROSION CHECK (1/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Corrosion repair operation to be carried
out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
Repair to be carried out:
Date of repair:
6.18
Stamp
ANTICORROSION CHECK (2/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Corrosion repair operation to be carried
out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
6.19
ANTICORROSION CHECK (3/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Corrosion repair operation to be carried
out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
Repair to be carried out:
Date of repair:
6.20
Stamp
ANTICORROSION CHECK (4/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Corrosion repair operation to be carried
out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
6.21
ANTICORROSION CHECK (5/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Corrosion repair operation to be carried
out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
Repair to be carried out:
Date of repair:
6.22
Stamp
ANTICORROSION CHECK (6/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Corrosion repair operation to be carried
out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
6.23
6.24
ALPHABETICAL INDEX (1/5)
A
ABS ..............................................................1.57, 2.22 → 2.25
access to the rear seats .................................................... 1.21
accessories........................................................................ 5.32
accessories socket ............................................................ 3.21
additional methods of restraint .....................1.25 → 1.28, 1.31
side protection ............................................................. 1.30
to the front seat belts .......................................1.25 → 1.28
to the rear seat belts ........................................1.25 → 1.29
adjusting your driving position ....................... 1.15 – 1.16, 1.22
advice on antipollution ...........................................2.15 → 2.17
air bag...........................................................1.25 → 1.31, 1.57
activating the front passenger air bags ........................ 1.50
deactivating the front passenger air bags .................... 1.48
air conditioning ........................................................3.4 → 3.11
air vents ...................................................................... 3.2 – 3.3
anti-corrosion check ..............................................6.18 → 6.23
anti-corrosion protection .................................................... 4.14
anti-lock braking system: ABS ...............................2.22 → 2.25
antipollution
advice .......................................................................... 2.15
armrest:
front .............................................................................. 3.18
ashtray ............................................................................... 3.21
ASR (traction control) ............................................2.22 → 2.25
audible and visual signals.................................................. 1.75
automatic gearbox (use) ........................................2.41 → 2.43
automatic gearbox selector lever...........................2.41 → 2.43
B
battery............................................................ 1.58, 4.12 – 4.13
troubleshooting ................................................. 5.28 – 5.29
bonnet.................................................................................. 4.2
brake fluid ............................................................................ 4.9
bulbs
changing ..........................................................5.15 → 5.23
C
catalytic converter..................................................... 2.9 – 2.10
central door locking ........................................1.8, 1.12 → 1.14
changing a bulb .....................................................5.15 → 5.23
changing a wheel.................................................... 5.10 – 5.11
changing gear ...............................................2.11, 2.41 → 2.43
child restraint/seat .............................1.32 – 1.33, 1.35 → 1.50
child safety.........1.2, 1.6, 1.11, 1.32 – 1.33, 1.35 → 1.50, 3.12
child seats..........................................1.32 – 1.33, 1.35 → 1.47
children ...................................... 1.10 – 1.11, 1.32 – 1.33, 1.33
children (safety) .......................................... 1.2, 1.6, 1.11, 3.12
cigar lighter ........................................................................ 3.21
cleaning:
inside the vehicle .............................................. 4.16 – 4.17
clock .................................................................................. 1.73
closing the doors ...................................................1.10 → 1.13
control instruments ................................................1.56 → 1.63
controls ..................................................................1.52 → 1.55
coolant ........................................................................ 1.60, 4.8
courtesy light ...................................... 3.15 – 3.16, 5.24 – 5.25
courtesy mirrors ................................................................. 3.16
cruise control ................................................1.57, 2.28 → 2.34
cruise control-speed limiter....................................2.28 → 2.34
customised vehicle settings .............................................. 1.72
customising the vehicle settings ....................................... 1.72
D
dashboard..............................................................1.52 → 1.55
daytime running lights........................................................ 1.76
deadlocking the doors ......................................................... 1.8
dimensions ................................................................6.6 → 6.8
dipstick................................................................................. 4.4
display ...................................................................1.56 → 1.61
doors.............................................................. 1.10 – 1.11, 1.14
doors/tailgate .......................................... 1.8, 1.10 – 1.11, 1.14
driver’s position .....................................................1.52 → 1.59
7.1
ALPHABETICAL INDEX (2/5)
driving ........2.2 → 2.5, 2.9 → 2.17, 2.19 → 2.25, 2.28 → 2.38,
2.41 → 2.43
driving position
settings ............................................................1.22 → 1.24
E
electric beam height adjustment ........................................ 1.80
electric windows ....................................................3.12 → 3.14
electronic parking brake ........................................2.12 → 2.14
Electronic Stability Control: ESC ...........................2.22 → 2.25
emergency brake assist.........................................2.22 → 2.25
emergency braking ................................................2.22 → 2.25
emergency key ........................................................... 1.2 – 1.3
emergency spare wheel ...................................................... 5.2
engine oil ..........................................................1.58, 4.3 → 4.7
engine oil capacity .....................................................4.5 → 4.7
engine oil level ...........................................................4.3 → 4.7
engine standby ..........................................................2.6 → 2.8
engine start/stop button .............................................2.3 → 2.5
environment ....................................................................... 2.18
ESC: electronic stability control .............................2.22 → 2.25
external temperature ......................................................... 1.73
F
faults
operating faults ................................................5.36 → 5.41
filter
air filter ......................................................................... 4.10
diesel filter .................................................................... 4.10
oil filter ......................................................... 4.6 – 4.7, 4.10
particle filter ................................................................. 1.59
passenger compartment filter ...................................... 4.10
fitting a radio ...................................................................... 5.31
fittings ....................................................................3.17 → 3.20
front passenger air bag deactivation ................................. 1.48
7.2
front seat
driver’s position memory .............................................. 1.20
front seat adjustment .............................................. 1.17 – 1.18
front seats
adjustment ..........................1.15, 1.17 – 1.18, 1.22 → 1.24
with electric controls .................................................... 1.19
with manual controls .................................................... 1.17
fuel
advice on fuel economy ............................................... 2.15
capacity ........................................................................ 1.84
filling ........................................................1.59, 1.84 → 1.86
grade ................................................................1.84 → 1.86
fuel economy .........................................................2.15 → 2.17
fuel filler cap ..........................................................1.84 → 1.86
fuel level ............................................................................ 1.60
fuel tank
capacity ............................................................1.84 → 1.86
fuel tank capacity ...................................................1.84 → 1.86
fuses ....................................................................... 5.26 – 5.27
G
gear lever........................................................................... 2.11
glove box ........................................................................... 3.19
H
handbrake................................................................. 1.56, 2.11
hands-free telephone integrated control ............................ 3.35
hazard warning lights signal ................................... 1.75 – 1.76
headlight beam adjustment ............................................... 1.80
headlight flashers .............................................................. 1.75
headlight washer ............................................................... 1.82
headrest.................................................................. 1.15 – 1.16
heating and air conditioning system .................................. 3.11
heating system ........................................................3.4 → 3.10
hill descent control .................................................2.22 → 2.25
Hill Start Assist.......................................................2.22 → 2.25
ALPHABETICAL INDEX (3/5)
horn ................................................................................... 1.75
horn:
flash ............................................................................. 1.75
sounding the horn ........................................................ 1.75
hubcap tool ................................................................. 5.8 – 5.9
I
indicators .............................................1.56, 1.75, 5.15 → 5.17
indicators:
direction indicators .............................................. 1.75, 5.18
exterior temperature indicator ...................................... 1.73
instrument panel ..............................................1.56 → 1.63
instrument panel ...........................................1.56 → 1.71, 1.76
instrument panel messages...................................1.62 → 1.71
interior trim
maintenance ..................................................... 4.16 – 4.17
J
jack ...................................................................................... 5.8
L
lane departure warning .................................. 1.59, 2.26 – 2.27
levels:
brake fluid ...................................................................... 4.9
coolant .................................................................. 1.60, 4.8
fuel ............................................................................... 1.60
windscreen washer reservoir ....................................... 4.10
lifting the vehicle
changing a wheel .............................................. 5.10 – 5.11
lighting:
exterior .............................................................1.76 → 1.79
instrument panel .......................................................... 1.76
interior ........................................... 3.15 – 3.16, 5.24 – 5.25
lights
adjustment ................................................................... 1.80
changing bulbs .................................................5.15 → 5.17
front ..................................................................5.15 → 5.17
mobile directional ......................................................... 1.78
lights:
adjusting ...................................................................... 1.80
brake lights .................................................................. 5.18
dipped beam headlights .................1.56, 1.76, 5.15 → 5.17
direction indicators .........................1.56, 1.75, 5.15 → 5.18
fog lights .................................................... 1.56, 1.79, 5.18
hazard warning ............................................................ 1.75
main beam headlights ....................1.56, 1.78, 5.15 → 5.17
number plate lights ...................................................... 5.23
reversing lights ............................................................. 5.18
side lights ............................................................ 1.76, 5.18
locking the doors ............................................1.2 → 1.11, 1.14
luggage compartment cover .............................................. 3.26
luggage retaining net .............................................. 3.32 – 3.33
M
maintenance:
bodywork .......................................................... 4.14 – 4.15
interior trim ........................................................ 4.16 – 4.17
mechanical ................................................4.2, 6.12 → 6.17
mileage before service .....................................6.12 → 6.17
map reading lights .................................................. 3.15 – 3.16
menu for customising the vehicle settings ......................... 1.72
methods of restraint in addition to the front seat belts ..............
1.25 → 1.28
methods of restraint in addition to the seat belts ...1.25 → 1.31
multimedia equipment ....................................................... 3.35
N
navigation .......................................................................... 3.35
navigation system .............................................................. 3.35
O
oil change ..................................................................4.3 → 4.7
7.3
ALPHABETICAL INDEX (4/5)
opening the doors ..................................................1.10 → 1.13
operating faults ................................ 1.56 → 1.59, 5.36 → 5.41
P
paintwork
maintenance ..................................................... 4.14 – 4.15
parking distance control.........................................2.35 → 2.40
power-assisted steering..................................................... 1.51
pretensioners ..................................................................... 1.25
puncture.................................................... 5.2, 5.8, 5.10 – 5.11
R
radio................................................................................... 3.35
fitting a radio ................................................................ 5.31
rear bench seat....................................................... 3.22 – 3.23
rear parcel shelf ...................................................... 3.25 – 3.26
rear screen de-icing/demisting ..................................... 3.5, 3.9
rear seats
functions ........................................................... 3.22 – 3.23
rear view camera .................................................... 2.39 – 2.40
rear view mirrors ................................................................ 1.74
RENAULT ANTI-INTRUDER DEVICE (RAID) ................... 1.14
RENAULT card
battery .......................................................................... 5.30
use .......................................................................1.2 → 1.9
RENAULT card battery ...................................................... 5.30
replacement parts .............................................................. 6.11
reverse gear
selecting ..................................................2.11, 2.41 → 2.43
reversing sensor ....................................................2.35 → 2.38
roof bars ............................................................................ 3.34
roof rack
roof bars ....................................................................... 3.34
running in ............................................................................. 2.2
7.4
S
screen wash/wipe .............................................................. 1.83
seat belt pretensioners ..........................................1.25 → 1.28
front seat belt ...................................................1.25 → 1.28
seat belts ..................................1.22 → 1.28, 1.30 – 1.31, 1.59
see-me-home lighting ............................................... 1.78, 1.80
service sheets........................................................6.12 → 6.17
side indicator lights
changing bulbs ............................................................. 5.23
side protection devices ...................................................... 1.30
signals and lights ...................................................1.76 → 1.80
speakers
location ........................................................................ 5.31
special features of diesel versions..................................... 2.10
special features of petrol vehicles ....................................... 2.9
speed limiter .................................................1.57, 2.28 → 2.30
starting the engine .....................................................2.3 → 2.8
steering wheel
adjustment ................................................................... 1.51
Stop & Start ...............................................................2.6 → 2.8
Stop & Start function..................................................2.6 → 2.8
stopping the engine ...................................................2.3 → 2.5
storage compartment.............................................3.17 → 3.20
storage compartments ..................... 3.17 → 3.20, 3.27 → 3.29
storing the driver’s seat position ........................................ 1.20
sun visor ............................................................................ 3.16
sunroof...................................................................3.12 → 3.14
switching on the vehicle ignition .......................................... 2.4
T
tailgate ...........................3.24 – 3.25, 3.27 → 3.29, 3.32 – 3.33
tanks and reservoirs
brake fluid ...................................................................... 4.9
coolant ........................................................................... 4.8
tanks and reservoirs:
windscreen washer ...................................................... 4.10
ALPHABETICAL INDEX (5/5)
technical specifications ..........................6.3 → 6.8, 6.10 – 6.11
telephone ........................................................................... 3.35
temperature regulation ............................................3.6 → 3.10
tool kit .................................................................................. 5.8
towing
breakdown ........................................................ 5.34 – 5.35
towing equipment .............................................. 3.30 – 3.31
towing a caravan ........................................... 3.30 – 3.31, 6.10
towing equipment
fitting ................................................................. 3.30 – 3.31
towing hitch...................................................... 5.8, 5.34 – 5.35
towing rings ........................................ 1.35 – 1.36, 3.30 – 3.31
towing weights ................................................................... 6.10
traction control: ASR ..............................................2.22 → 2.25
traction control system: ASR .................................2.22 → 2.25
transporting children ..........................1.32 – 1.33, 1.35 → 1.50
transporting objects
in the luggage compartment ............................3.30 → 3.33
luggage net ....................................................... 3.32 – 3.33
trims ..................................................................................... 5.9
trip computer and warning system... 1.56 → 1.59, 1.62 → 1.71
tyre inflation kit...........................................................5.3 → 5.7
tyre pressure........................................2.19 → 2.21, 4.11, 5.13
tyre pressure monitor.............................................2.19 → 2.21
tyre pressures .................................................................... 4.11
tyres ........................................ 2.19 → 2.21, 4.11, 5.12 → 5.14
warning lights................................... 1.56 → 1.59, 1.62 → 1.71
washing .................................................................. 4.14 – 4.15
weights .............................................................................. 6.10
wheelbrace .......................................................................... 5.8
wheels (safety) ......................................................5.12 → 5.14
windscreen de-icing/demisting ..................................... 3.5, 3.9
windscreen washer .......................................1.81 → 1.83, 4.10
windscreen washer/wiper ....................................... 1.81 – 1.82
wiper blades ...................................................................... 5.33
wipers ....................................................................1.81 → 1.83
blades .......................................................................... 5.33
U
unlocking the doors ................................................ 1.12 – 1.13
V
vehicle identification plates ........................................6.3 → 6.5
ventilation ................................................................3.4 → 3.10
W
warning buzzer ....................................... 1.10, 1.58, 1.75, 1.78
7.5
( www.e-guide.renault.com )
RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO
92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60
NU 966-4 – 99 91 036 08R – 02/2013 – Edition anglaise
à999103608Rëóêä C5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising