Page 1 YONGNUC) YN-622N i-TTL Wireless Flash Trigger

Page 1 YONGNUC) YN-622N i-TTL Wireless Flash Trigger
YONGNU®@
YN-622N
-TTL
Wireless Flash Trigger
Transceiver
| D 1 G IT AL |
| C1 A |
1 ca YN-622N в 7
| -TTL |
| Wireless Flash Trigger
| СЗ Transceiver
|| CH/AE GP/MODE
| TEST/-
User Manual
HP
CONTENTS
Conventions used in the manual . 1
General Description . 2
Supported Functions List . 3
Compatibility List . 4
Name of Parts Co. .. . . . . 5
Preparation Before Use. . . . . . . . . . . 6-7
Setting . . . aaa O
Flash Awaking /Testing Flash. Cee 13
Usage . . . . . . . . . . . . . . . .. 14- 17
Troubleshooting . . . . . . . . . . . . . 18
Specifications . . . . . . . . . . . 2... . 19
Cautions
e Please turn off power supplies of all equipment
when connecting or installing the product.
e Please keep It dry. Be sure not to use wet hand to
touch the product. It is also not allowed to immerse the
product into waster or make it be exposed in the rain;
otherwise It may not work normally or even be
damaged.
Do notuseitinexplosive situations; violation of this
warning may cause an explosion or fire.
* This product involves battery, please be in strict
accordance with the relevant provisions on the use of
the battery, otherwise it would cause property damage
or personal injury.
Conventions used in the manual
+ Read this user manual while also referring to
your camera's & flash's user manual before using in
order to correct use this product.
The functions described in this user manual are all under the
conditions that: all transceivers are set in the same channel,
power of all equipments are on, enabled the flash firing.
This product is a wireless transceiver design, if the
product is not in transmitting state, it will be
automatically converted to receiving (stand by) state, in
this manual, the product will be called transmitter
when it installed on the camera hot shoe, while
installed or connected to the flash, it will be called
receiver.
__ #9 Off-Camera Flash
Receiver
« The belowicon used in this manual
mm) Refers to long press(hold down) the button.
np Refers to half press the camera shutter button or
short press the button.
CH/4| When describing the function of the key increase
TEST/-|/ decrease parameter values will using the + / -.
General Description
Thank you for purchase the products of Yongnuo firstly.
* YN-622N 1I-TTL wireless transceiver is a high
performance 2.4G wireless flash trigger designed for
Nikon users. Different photographic effects can be
realized through setting the flash at 360 degrees. It
supports I-TTL and manual flash, front-curtain sync, rear-
curtain sync and high-speed sync(Auto FP), the highest
sync speed is 1/8000s*. it can remote change flash
exposure compensation or flash output of each group,
supports different flash mode mix using. Supports the
transmitter installed i-TTL flash, in addition, it supports
the master unit on transmitter sets the parameters of
each group. This product is a wireless transceiver
design, the distance of remote control reaches 100M,
supporting 7 wireless channels and A/B/C three groups,
and with AF assist beam emitter function.
- YN-622N 2 transceivers kit consist two similar
transceivers, support one camera controlling multiple
flashes at the same time. Install the flashes with the
receiver additionally purchased to make them into an
application form of multiple-flashes, number of the
receivers is not limited.
X Compatible cameras/flashes is needed when using TTL
function
* The highest sync speed of some camera types is
1/4000s, some of flash or camera models may reach to
1/250s only or less if it doesn't support high sync
speed.
Supported Functions List
. Compatible flash mode: i-TTL, Manual flash
. Compatible Shutter sync: front-curtain sync, rear-
curtain sync and high-speed sync(HSS/FP), the highest
sync speed is 1/8000s
+ Support remote set the parameters of flash through
the transceiver (Remote Control Mode)
+ Support i-TTL/Manual/Repeating flash mode mix
using(Mix Control Mode)
. Support the flash installed on transmitter(on-top
flash)and supports i-TTL function
‚ Support the use of master unit on transmitter sets the
parameters of each group(Master Control Mode)
. Support FEC, FVL function
. Support modeling flash and red-eye reduction flash
. Support flash zooming (auto)
. Built-in AF assist beam emitter (AF Lamp)
+ Settings saved automatically
. Compatible with YongNuo/ Nikon series flashes
+ Support PC port triggering strobe flashes
+ PC port support front/rear curtain sync and high-
speed sync(Super Sync)function
+ Support single-contact of camera & flash triggering
(max sync speed is 1/250s)
Compatibility List
Functions supported by the product depend on the
camera and flash used. In this user manual, assumes
that you are using the compatible camera/flash.
Updated version of the compatibiulity list and this
usermanual can be got from www.hkyongnuo.com
Compatible camera list :
Nikon
D70/D70S/D80/D90
D200/D300/D300S/D600/D700/D800
D3000series/D5000series/D7000series
Compatible i-TTL flash list :
YongNuo
YN465N/YN467N/YN-468N(II) YN565N/YN568N
Nikon
SB-400/SB-600/SB-/00/SB-800/SB-900/SB-910
List of that the master unit using master control
mode on the transmitter is supported (refer to p15):
SB-/700/SB-900/SB-910/SU-800
X The follow functions refer to the
manufacturer of the camera and flash.
+. Flash Value Lock(FVL)
- Modeling Flash
о Red-eye Reduction Flash
+ ZOOM(flash coverage):Support the auto zoom
which mounted on the top and off-camera flash . Please
set manually zoom on the flash if you do not need auto
zoom.
Name of Parts
YN-622N
TTL
C2
Wireless Flash Trigger
C3 Transceiver
Г" IIE IIE IEE IESE ESS ESS ESS ESE ESS ESE ESE a a a a a a a a a a a a
|
Short press AF Long press | fi
take effect [CH|/| F | take effect |
A |Channel indicator I] IPC port
B |Group indicator ) JAF assist beam emitter
C |Channel /AF lamp setting button K |Locking ring
D | Group /Made setting button L |Mounting foot
E | Test button M [locking pin
F |State indicator N |Eyelet
G |Power switch O |Battery compartment cover
H |Hot shoe P |Battery compartment
Communication state State indicator | Channel indicator | Group indicator
Stand by ( receive) Go out Go out
Receiving Blink Blink
Manual Flash-Transmitting ORANGE Blink Blink
I-TTL FlashTransmitting Blink Blink
Preparation Before Use
1. Installing the Batteries “a
Open the cover and install two AA
batteries (excluded)according to
the marks , rechargeable batteries
of 1.2V can be used. Status
Indicator will blinks in red when the
battery is low, replace the battery. BAT AA x ==
LT UU
eps
| о ООЛОООООНННОЦ
|
GATT OPEN
¥ Remove the batteries when the product ~
is not used for long time.
x Please replace the both two batteries at
the same time. |7
2.Installing the Transceiver on the Camera (As
Transmitter)
( NL
DO x | | ve
O-8
(2)
- wm (1
= J
1). Unscrew the locking ring of the transceiver.
~
3)
2). Slip the mounting foot into the hot shoe of the camera.
3).Turn the locking ring according to the direction
of arrow, the locking pin will protrude from the
mounting foot.
X It is supported that install a on-top flash (or master
unit) on the transmitter, refer to p15.
Preparation Before Use
3.Install Flash on the Hot Shoe of the Receiver
1. Install the transceiver on the mini
stand or other fixing equipment
cc # (excluded).
а Е <« | 2 Loosenthelockingring of the flash.
> 3. Slip the mounting foot of the flash
into the receiver.
= 2) 4. Tightly lock the locking device of
|
the flash.
> т Caution! The hot shot of the |
| transceivers can only install flash
| being applicable to DSLR cameras, |
can not install high-voltage flash,
| or the transceiver may be damaged. |
4.Sets the Flash Mode according to the Control Mode
1).Remote Control Mode: refer to pl4.
2).Mix Control Mode: refer to p14.
3).Master Control Mode(Master input): refer to p15.
+ Check that all equipments are installed and
connected reliably before use, turn all equipments on,
setting the transceivers in the same channel, set the
group of receivers, set the control mode according to
your requirement, setting the flash mode before using,
test button can be used to awaken and test whether the
flash works before shooting, press the shutter button
until the flash recyling completely, and flash fire.
1. Power Switch
Power on when the power switch slides
to [ON], power off when the power
switch slides to [OFF].
2. Channel Setting
Short press the[CH/+] button and the
channel indicator will keep lighting for
several seconds to indicate the current
channel, at this time shortly press the
button again to change channel, and
there are totally 7 channels. Set all the
transceivers at same channel.
Te | C1 | с! Te ter | C1 te
|2 po e ca e ca po
]c3 | СЗ Tes | СЗ Tes e Tes
np CHIE np CHIE: np CH/T np CH/5F np CHI np CH/ np CH/T
CHI СН2 CH3 CH4 CHS CH6 CH/
3.Receiver group setting
In standby state short press | -a° A
the [GP/MODE] button to
view the current receiving
groups, then short press the © ©
button again to switch |[ermo dann jornvone qu
between A/B/C the three
B BT
groups. A B
4. Transmitter group setting
Method 1:
1).Half press the camera button to
enter into the transmitting state. .
2).Short press the [GP/MODE] button
in the transmit state, set the!
transmitting group, then the.
indicator light will display the |
groups involved in flash. В
ZA A A ZA: ZA A ZA:
pL в 28: : 84 |) 5
с с ze: с Ze: Ze: ze:
GP/MODE qu GP/MODE qui GP/MODE qu GP/MODE qu GP/MODE qu GP/MODE qu GP/MODE qu
A B C A+B A+C B+C A+B+C
Method 2: r |
Hold down the [TEST/-] or PT
button in standby state, = TEST/- “amc a
and short press the
[GP/MODE] button to set.
5.Set the transmitter flash mode*
Long press the [GP/MODE] button until
the indicator light switch between green
(i-TTL flash) or orange (manual flash).
* Remote control mode only
6.Set the flash parameter of each group on the
transmitter (remote control mode)
° i-TLL transmitting state: increase/decrease the flash
exposure compensation(FEC), supporting the FEC set
between -3 to +3 with 1/3 or 1 step.
«+ Manual transmitting state: increase/decrease the flash
output(refer to p11).
1).Half-press the shutter button of the camera to enter the
transmitting state.
2).Hold down the [+] or [-] button to set:
Hold down the [+] (or [-]) button, the indicator will blinking
circulated with A=» B— C— C1— С2— C3—> A... loose the button
when indicator stay on A/B/C, the indicator will fast blink one
times, the FEC (or flash output ) of the corresponding group
will increase/decrease 1/3 step; loose the button on C1/C2/C3,
the indicator will fast blink three times, the corresponding
group will increase/decrease 1 step.
Ue
C1 corresponds to group À
C2 corresponds to group B
C3 corresponds to group C
Example: as shown in figure, hold down the [+] button in
transmitting state, release until C2 indicator on, it will increase
1 step of the FEC (or flash output) on the flash for group B
receiver.
X It is supported to set the FEC on the flash directly , the
compensation value shall be superposed according to
flash setting plus the transmitter setting.
Manual Flash Output Control(remote control mode)
- YN-622N provides a general way of manual control
of the flash output . For the same manual flash output
values of 622N, even using different GN of the flash, the
output is the same (in case not exceed the effective
range of the flash).
° The minimum manual flash output value ot 622N 15 1,
the maximum flash output according to different GN of
the flash, the default value is 8, add 1 step is 10.4, add 1
step is 16, and so on. The value of 622N is proportional,
when the value A is twice as B, the flash output of the
former is half of the latter, refer to the form below.
1 1.3 1.7 2 2.6 3.4 4 5.2 6.8 8 10.4
16 20.8 | 27.2 32 41.6 | 54.4 64 83.2 | 108.8 | 128
13.6
When the 622N using master contorl mode(refet to
p15), the manual output values of the master unit and
manual output value of YN-622N convert as below:
MASTER
1/128
+0.3
+0.7
1/64
+0.3
+0.7
1/32
+0.3
+0.7
1/16
+0.3
+0.7
YN-622N
1
1.3
1.7
2
2.6
3.4
4
5.2
6.8
8
10.4
13.6
MASTER
1/8
+0.3
+0.7
1/4
+0.3
+0.7
1/2
+0.3
+0.7
1/1
YN-622N
16
20.8
27.2
32
41.6
54.4
64
83.2
108.8
128
X When setting the flash mode and parameters on the
transmitter, the screen of the flash on the receiver will not
change.
X Restart the transmitter will
compensation or the flash output setting.
compensation=0 /Value of Manual flash=8)
X When the setting parameters reach the maximum or
minimum, the corresponding indicator will not blink.
restore the default
(i-TTL
7.Flash Shutter Sync:
- Refer to the camera’ s setting. Supports front-curtain
sync, rear-curtain sync and high speed synchronous
(HSS/Auto FP*).
*Using high-speed synchronization need to set the flash
sync speed of the camera to AUTO FP.
*The maximum high-speed synchronization speed is
1/8000s or 1/4000s (depends on the camera).
*Some models of camera does not support the HSS
(without Auto FP option), the shutter speed will be
limited to 1/250s or less when using this kind of camera.
8.AF Assist Beam Emitter
« When using AF under low-light, the To |
built-in AF-assist beam emitter of the FSU |
transmitter will be emitted [cvs [TIT
automatically to make it easier to ЧИ
autofocus, and the on-top flash which 3]
support AF assist beam emitter function —
can also be emitted at the same time. —
Enable/disable (stand by)
State Channel AF assist
Operate indicator beam emitter
Press [CH/4] button On Enable
less than 3 seconds Off Disable
press [CHI buttor Blinking three times | Enable/Disable
X It need to using single AF of the camera.
Xx Both the receiver and the off-camera flash on the
receiver will not be emitted.
Flash awaking and testing flash
+ When half press the shutter button of the camera,
the hot-shoe flash will be awaken.
» In standby state, pressing the [TEST/-] button of the
transceiver will awake the flash. When loosening the
button, the flash of the group having been selected will
fire a test flash.
+ Intransmitting state, short press the [TEST/-] button
will fire a test flash.
о Refer to the following figure, the transmitter sets
A+B two groups of flash, hold down the [Test/-] button,
the flash on A and B of the receiver will be awakened,
I G 1 T A L
YN-622N
i-TTL
ransceiver
X If the flash can not be awakened, manually
awaken the flash before shooting.
X Using PC port to connect with flash without the
awakening function.
X All the indicators going out when flash
fires(Receiver).
+ 2 Transceiver kit packages « Compose multiple
Use 1 off-camera flash or 1 off- groups through additional
camera flash + 1 on-top flash. purchase transceiver.
1.Remote Control Mode: | ===
e Set the flash(receiver) to i- |!
TTL flash mode, the flash will | |"
fire according to the flash mode |
and parameters set by the | E ®))) ==
transmitter, support |-
TTL/Manual Flash. ( P9-11) e
2.Mix Control Mode =
* Supports the use of flash on
I-TTL REMOTE, MASTER
ОМ
OO OO OFF =
O,
Г T
|
|
the transmitter or the receiver | RPT
works at the same time In |! o
different flash modes include i- | ' fe =
TTL, Manual, RPT flash. a a
UEN ——
Set the flash on the receiver to Manual or RPT flash mode,
the flash will work according to the mode and parameters
displayed; Set to i-TTL flash mode, it will work according to
the transmitter’ s setting(same to the remote control
mode), the on-top flash refer to p15.
3.Master Control Mode& On-top flash.
1.Power on of the on-top flash: First turn on the on-
top flash, then turn on the transmitter.
2.The on-top flash use non master control model:
« Flash modes, exposure compensation (flash output),
zoom or other parameters set directly on the flash, not
affected by the transmitter settings. Supports i-TTL,
Manual, Repeating flash.
3.The on-top flash use master control mode:
- Using the on-top flash(master unit) which support
master mode to set each group of flash mode and
parameters, support i-TTL, Manual flash.
1.Turn on the master unit and| f :
set to MASTER(commander
mode), then turn on the
transmitter.
2.Set the receiver group, turn
on the flash(Do not set to
remote), and set to I-TTL
flash mode.
3.Set the flash mode and parameter on the master
unit of each group (refer to the manufacturer's
usermanual). It will communicate via the YN-
622N transceiver's channel.
4.Use the test button of the transmitter to test flash and
shoot, the flash fires.
XThe master unit set on the on-top of the transmitter
will not transmit infrared commands.
| Caution! Do not connect to the PC| la
port any flash requiring trigger
| voltage more than 300V, or the |
| transceiver may be damaged.
+ Purchase corresponding PC flash sync cord according to
the different ports of the flashes needs.
1. Use an end of PCsync cord with nut to connect to the receiver.
2. The other end of the PC sync cord connects to strobe flashes
or other flashes which supporting PC port.
3. Setthe camera's shutter sync as front-curtain or rear-curtain.
4. Adjust shooting parameters and shoot.
* Super sync: Use the non-high speed sync flash to realize
higher sync speed, this function is more applicable to strobe
flashes whose flash duration is longer, and it is for the camera
which support Auto FP only.
1. Connect the receiver to flash via PC port and it may needs
setting at manual full-power flash output (1/1).
2. Set the flash sync speed of the camera as AUTO FP, the
maximum shutter sync speeds can reach to 1/8000s. Take
photos and check whether the photos are synchronous , it
may see gradations or variations in the photos, results
depend on the camera and flash.
The PC port is for output using only.
Flashes on the hot shoe and connecting to the PC port
can be used at the same time.
5. The single contact camera/flash: Manually
setting the flash output
1).Transmitting group setting: According to the
transmitter group setting method 2(P9).
2).Flash mode setting (on the flash):Set to manual
flash mode, use the transmitter's main flash trigger
contact; but it does not support high synchronous
speed or other TTL function(the maximum
synchronous speed is 1/250s or less).
* Factory Reset
f
mo 1.)Hold down [cH/Æ] + [GP/MODE]
1 G I T A L
button at the same time.
2.)The indicator light will light up in
sequence from A>B>C—C1—>C2—
C3—state indicator (red).
3.)Loose all the buttons will restore
factory reset.
° About the Max Sync Speed
It needs the camera and flash both support hi-speed
sync, and the max sync speed is 1/8000s or 1/4000s.
When using the hot shoe flash which doesn’ t support
hi-speed sync, the max sync speed is 1/250s or lower.
- About Automatic Saving Function
The transceiver will auto saving the sets such as
channel, receiving group, AF assist beam. The exposure
compensation and flash output will not be saved.
Troubleshooting
1. Fail to power on or automatic shutdown:
e The battery is loaded inversely or exhausted; it will power
off automatically when the battery is going to be
exhausted in case of being over discharged.
A Install the battery according to the correct direction the
battery compartment indicates and ensure the battery is
full and restart the power (refer to page 6).
2. The flash doesn't fire
Ensure the power of all equipments are full, the
connection among the transceiver, camera and the flash
IS reliable; whether the indicator is set in the same
channels and controllable groups. Flashes recycle
process, entering in the state of overheating protection,
ongoing zoom adjustment, the flash enters into sleep
status etc. may makes the flash doesn't fire . Ensure the
flash is in ready state, use the [TEST/-] button test the
flash before using.
3.i-TTLunderexposure or overexposure:
Check whether the camera body or the flash set
compensation setting.It may be underexpose if exceeds
the flashing effect distance . It may overexposure when
TTL and manual flash are used at the same time, now the
manual flash suits to be used as a backlight.
% Itis suggested using the following procedures to
deal with when other trouble occur during the using:
1). Restart all the equipments.
2). Replace the batteries of the transceivers.
3). Reset the factory set of the transceivers.
4). Reset the factory set of the camera/flash.
Specifications
System type: Digital FSK 2.4GHz wireless transceiver
Distance: 100M
Channel: 7
Flash mode: i-TTL, Manual flash
Sync mode: front-curtain sync, rear-curtain sync, Hi-
speed sync(Auto FP)
Groups: 3Groups (A/B/C)
Sync speed: 1/8000s*
Input: Hot-shoe
Output: Hoe shoe, PC port
Compatible type of flash: Hot-shoe flash, Strobe flash
Battery: AAX2 (support 1.2 V rechargeable battery)
Stand-by time: 60h
Dimensions: 89.5x53x39mm
Weight:78g
* Sync speed of part of cameras and flashes may be
lower.
X All of the specification parameters are base on test
conditions of our company. All registered trademarks
are the property of their respective owners in this
usermanual. Specifications subject to change without
notic.
V1.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising