Manual Source1 S1-THEH21NS Rev 4

Manual Source1 S1-THEH21NS Rev 4
Owner ’s Manual
HVAC SERVICE PARTS
Model
S1-THEH21NS
TM
Heat Pump Digital
Non- Programmable
Therm ostat
Control up to 2-Heat & 1-Cool
Battery or System Powered
Use with most
Heat Pump systems:
1-Heat, 1-Cool
2-Heat, 1-Cool
Auxiliary Heat Indicator
Fahrenheit or Celsius
Copyright
2007 Source1
OWNER'S MANUAL
S1-THEH21NS
Contents
Page #
Safety Warnings
Front Panel
Display
Normal Operation
Aux Heat
Fahrenheit or Celsius
Preparation
Remove Old Thermostat
Battery Replacement
Wire Connections
Test Operation
Troubleshooting
Warranty
Page 2
OWNER'S MANUAL
S1-THEH21NS
Safety Warnings
P/N S1-THEH21NS
CAUTION
Follow Installation Instructions carefully.
DISCONNECT POWER TO THE HEATER AIR CONDITIONER BEFORE REMOVING
THE OLD THERMOSTAT AND INSTALLING
THE NEW THERMOSTAT.
WARNING
CAUTION
The two Alkaline “AA” batteries must be replaced at
least once every 12 months to ensure proper
operation. The “Low Battery” icon will appear on the
thermostat display when it is time to replace the
batteries. If the thermostat is connected to 24v power,
the batteries should still be installed, but are not
required.
When “Low Battery” is displayed the batteries must be
replaced immediately. The manufacturer cannot be
liable for improper operation of the thermostat if the
batteries are not immediately replaced.
Annual battery replacement is especially critical in
locations subject to freezing temperatures. The
thermostat will be unable to turn on the heating system
if the batteries are exhausted.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
Page 3
OWNER'S MANUAL
S1-THEH21NS
Front Panel
MODE SWITCH
BATTERY Cool, Off, or Heat
DOOR
DISPLAY
AUX HEAT
SWITCH
Emergency
Normal
Lockout
COOLER &
WARMER
BUTTONS
FAN SWITCH
On or Auto
Page 4
OWNER'S MANUAL
S1-THEH21NS
Display
88
SET TEMP
AUX
HEAT
COOL
LOW
BATTERY
Heat and Cool indicators.
In normal operation, Heat or Cool appears, depending
on the Mode Switch position. When heat or cool is
energized, the Heat or Cool indicator will flash.
Current room or set temperature.
Desired set temperature indicator.
When this indicator is on, the large numbers represent
the desired room temperature. Pressing the
COOLER or WARMER button during normal operation
will cause the large numbers to switch from the current
room temperature to the desired set temperature.
Indicates battery life is low; it is recommended to
replace the batteries at this time.
Indicates auxiliary heat is energized.
Page 5
OWNER'S MANUAL
S1-THEH21NS
Normal Operation
MODE SWITCH
Cool, Off or Heat
COOLER & WARMER
BUTTONS
FAN SWITCH
On or Auto
Operation
Select Cool or Heat with the Mode Switch.
Normally leave the fan switched to Auto.
In Fan Auto, the fan will turn on only with a heat
or cool demand. When Fan On is selected, the
fan will run continuously.
Adjust the desired set temperature with the
COOLER or WARMER buttons.
Page 6
OWNER'S MANUAL
S1-THEH21NS
Aux Heat
AUX HEAT
SWITCH
Emergency - Disables all compressor
functions* and energizes only Aux
Heat to satisfy the heat demand.
Normal - Aux Heat is allowed to run, if necessary,
along with the heat pump to satisfy the
heat demand.
Lockout - Aux Heat will never turn on
regardless of the heat demand.
* When the Aux Heat switch is in the Emergency position the compressor will also be
locked out during cooling operation.
Page 7
OWNER'S MANUAL
S1-THEH21NS
Fahrenheit or Celsius
MODE SWITCH
Cool, Off or Heat
COOLER & WARMER
BUTTONS
Operation
Select Off with the Mode Switch.
Press and hold the COOLER and WARMER
buttons at the same time until the temperature
is displayed in degrees Celsius.
Repeat this process to display the temperature
in degrees Fahrenheit.
Page 8
OWNER'S MANUAL
S1-THEH21NS
Preparation
Proper installation of the thermostat will be
accomplished by following these step
by step instructions. If you are unsure
about any of these steps, call a qualified
technician for assistance.
These tools will be required:
Flat Blade
Screwdriver
Wire cutter
& Stripper
Make sure your Heat Pump is working
properly before beginning installation
of the thermostat.
Carefully unpack the thermostat.
Save the screws and instructions.
Turn off the power to the Heat Pump
system at the main fuse panel.
Page 9
OWNER'S MANUAL
S1-THEH21NS
Remove & Replace
Old Thermostat
Remove the cover of the old thermostat.
If it does not come off easily check for
screws.
Loosen the screws holding the thermostat
base or subbase to the wall, and lift away.
Disconnect the wires from the old
thermostat. Tape the ends of the wires
as you disconnect them, and mark them
with the letter of the terminal for easy
reconnection to the new thermostat.
Keep the old thermostat for reference
purposes, until your new thermostat is
functioning properly.
Page 10
OWNER'S MANUAL
S1-THEH21NS
Battery Replacement
The batteries are easily accessible from the battery
slot located on the front of the thermostat (fig. 1). To
open the battery slot, press down on the battery
cover (fig. 1) and pull out (fig. 2).
Pull out
Press
down
Battery
Slot
FIG. 1
FIG. 2
Remove the old batteries and replace with the new
Old
AA alkaline batteries (fig. 3).
batteries
out
alkAA
alin
e
COOLER
WARMER
EMERGENC
New
batteries
in
Y
NORMAL
LOCKOUT
OFF
COOL
HEAT
AUXILIA
RY HEA
T
FAN
ON
AUTO
FIG. 3
Place the bottom hook of the battery cover into the
slot and snap closed (fig. 4).
Snap closed
Bottom
Hook
FIG. 4
The batteries must be replaced immediately when
the thermostat displays the Low Battery icon.
Page 11
OWNER'S MANUAL
S1-THEH21NS
Wire Connections
If the terminal designations on your old
thermostat do not match those on the
new thermostat, refer to the chart below
or the wiring diagrams that follow.
Wire from the
old thermostat
terminal marked
C
Function
Install on the
new thermostat
connector marked
C (optional)
Common
Rc, R, M, Vr, A
Power
R
Y1 or Y
Cooling
Y
W1, W or H
Auxiliary Heat
W
G or F
Fan
G
B
Rev. Valve
B
(Energize to Heat)
O
O
Rev. Valve
(Energize to Cool)
Page 12
MADE IN CHINA
97061606
USE SIZE “AA”
ALKALINE BATTERIES
C
R
Y
W
G
B
O
4Z95
A label is provided on the
backplate that prevents drafts
originating inside the wall from
entering the thermostat.
These drafts, left unchecked, may
cause incorrect room temperature
readings.
Please do not remove this label
from the thermostat. Insert the wires
through the slots provided in the label
as shown in Fig. 1.
Wire Slots
MODEL: S1-THEH21NS
Thermal Insulating Sheet
OWNER'S MANUAL
S1-THEH21NS
Sample Wiring Diagrams
4 Wire, 1 Stage Cooling, 1 Stage Heat-Heat Pump with O reversing valve.
Residential Heat Pumps, split systems & package units, with no auxiliary heat.
Common wire optional*
C
R
Y
W
G
B
O
COMPRESSOR
Y
POWER
R
FAN
G
REVERSING VALVE
O
4 Conductor 18 to 22 gauge
unshielded cable from the
thermostat to the equipment.
* Common wire is optional in all installations.
If a common wire is not used the
thermostat must be powered by two AA alkaline batteries. These batteries
must be replaced (page 11) each year or when the Low Battery indicator is displayed
(page 3).
Page 13
OWNER'S MANUAL
S1-THEH21NS
Sample Wiring Diagrams
5 Wire, 1 Stage Cooling, 2 Stage Heat-Heat Pump with O reversing valve.
Residential Heat Pumps, split systems & package units, with auxiliary heat.
Common wire optional*
C
R
Y
W
G
B
O
COMPRESSOR
Y
POWER
R
AUXILIARY HEAT
G
FAN
W
REVERSING VALVE
O
5 Conductor 18 to 22 gauge
unshielded cable from the
thermostat to the equipment.
* Common wire is optional in all installations.
If a common wire is not used the
thermostat must be powered by two AA alkaline batteries. These batteries
must be replaced (page 11) each year or when the Low Battery indicator is displayed
(page 3).
Page 14
OWNER'S MANUAL
S1-THEH21NS
Sample Wiring Diagrams
4 Wire, 1 Stage Cooling, 1 Stage Heat-Heat Pump with B reversing valve.
Residential Heat Pumps, split systems & package units, with no auxiliary heat.
Common wire optional*
C
R
Y
W
G
B
O
FAN
G
COMPRESSOR
Y
POWER
R
REVERSING VALVE
B
4 Conductor 18 to 22 gauge
unshielded cable from the
thermostat to the equipment.
* Common wire is optional in all installations.
If a common wire is not used the
thermostat must be powered by two AA alkaline batteries. These batteries
must be replaced (page 11) each year or when the Low Battery indicator is displayed
(page 3).
Page 15
OWNER'S MANUAL
S1-THEH21NS
Sample Wiring Diagrams
5 Wire, 1 Stage Cooling, 2 Stage Heat-Heat Pump with B reversing valve.
Residential Heat Pumps, split systems & package units, with auxiliary heat.
Common wire optional*
C
R
Y
W
G
B
O
COMPRESSOR
Y
POWER
R
AUXILIARY HEAT
G
FAN
W
REVERSING VALVE
B
5 Conductor 18 to 22 gauge
unshielded cable from the
thermostat to the equipment.
* Common wire is optional in all installations.
If a common wire is not used the
thermostat must be powered by two AA alkaline batteries. These batteries
must be replaced (page 11) each year or when the Low Battery indicator is displayed
(page 3).
Page 16
OWNER'S MANUAL
S1-THEH21NS
Test Operation
Turn on the power to the Heat Pump.
On the thermostat, slide the Mode Switch
to HEAT. Press the COOLER or WARMER
button until the set temperature is 10 degrees
above room temperature. The HVAC unit
should energize in the heating mode.
Note: You may need to wait up to five minutes
for heating to energize due to the compressor
lockout feature. There is a two minute minimum run-time for first stage heating.
On the thermostat, slide the Aux Heat
Switch to the NORMAL position. The
Aux Heat icon will appear indicating that
the thermostat has energized Aux Heat
(page 7).
TWO STAGE OPERATION - The 2nd stage
of heat (auxiliary heat) is turned on when
the room temperature is equal to or less
than: the setpoint minus the 1st stage
deadband (one degree, non-adjustable),
minus the 2nd stage deadband (two
degrees, non-adjustable).
Cooling
Heating
2nd Stage
turn on
Deadband
Deadband
Deadband
db 2
(non-adj. 2 )
db 1
(non-adj. 1 )
db 1
(non-adj. 1 )
1st Stage
turn on
Page 17
Heat or Cool
Setpoint
1st Stage
turn on
OWNER'S MANUAL
S1-THEH21NS
Test Operation
On the thermostat, slide the Mode Switch
to COOL. Press the COOLER or WARMER
button until the set temperature is 10
degrees below room temperature. The
HVAC unit should energize in the cooling
mode (Page 6). Note: You may need to wait
up to five minutes for cooling to energize due
to the compressor lockout feature.
On the thermostat, slide the Mode Switch to
OFF. Slide the Fan Switch to Fan On. The
fan should turn on and run continuously
(Page 6).
Page 18
OWNER'S MANUAL
S1-THEH21NS
Trouble Shooting
SYMPTOM: The slide switches on the thermostat
are very difficult to move.
CAUSE: The backplate of the thermostat is
screwed too tightly into a wall that is not
perfectly flat.
REMEDY: Loosen the screws holding the
thermostat into the wall.
SYMPTOM: The Air Conditioning does not
attempt to turn on.
CAUSE: The cooling setpoint is set too
high, the Mode Switch is not set for
Cool, the batteries are too weak, or the
Aux. Heat Switch is set for Emergency.
REMEDY: Consult the Normal Operation
section in this manual to:
Lower the cooling setpoint (Page 6).
Correct the Mode Switch position (Page 6).
Replace the batteries (Page 10).
Adjust the Aux Switch to Normal (page 7).
SYMPTOM: The fan does not turn on even though
the compressor has energized.
CAUSE: The Fan Switch is not completely in the
On or Auto position.
REMEDY: Slide the Fan Switch firmly into the On
or Auto position.
Page 19
OWNER'S MANUAL
S1-THEH21NS
Trouble Shooting
SYMPTOM: Aux Heat does not turn on.
CAUSE: The Aux Heat Switch is set for
Lockout.
REMEDY: Consult the Aux Heat section
of this manual to slide the Aux
Heat Switch to Normal (Page 7).
SYMPTOM: The Heating does not attempt
to turn on.
CAUSE: The heating setpoint is set too
high, the Mode Switch is not set for
Heat, the batteries are too weak, or the
Aux Heat Switch is set for Emergency.
REMEDY: Consult the Normal Operation
section in this manual to:
Raise the heating setpoint (Page 6).
Correct the Mode Switch position
(Page 6).
Replace the batteries (Page 11).
Adjust the Aux Switch to Normal (Page 7).
Battery Stat P/N S1-THEH21NS
c
FC
Tested to Comply
with FCC Standards
FOR HOME OR OFFICE USE
4Z95
P/N 88-549
Rev. 4
Page 20
OWNER'S MANUAL
S1-THEH21NS
Warranty
One-Year Warranty - This Product is warranted to be free from defects in material and
workmanship. If it appears within one year from the date of original installation, whether or not
actual use begins on that date, that the product does not meet this warranty, a new or
remanufactured part, at the manufacturer’s sole option to replace any defective part, will be
provided without charge for the part itself provided the defective part is returned to the distributor
through a qualified servicing dealer.
THIS WARRANTY DOES NOT INCLUDE LABOR OR OTHER COSTS incurred for diagnosing, repairing,
removing, installing, shipping, servicing or handling of either defective parts or replacement
parts. Such costs may be covered by a separate warranty provided by the installer.
THIS WARRANTY APPLIES ONLY TO PRODUCTS IN THEIR ORIGINAL INSTALLATION LOCATION AND
BECOMES VOID UPON REINSTALLATION.
LIMITATIONS OF WARRANTIES – ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF
FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY) ARE HEREBY LIMITED IN DURATION TO
THE PERIOD FOR WHICH THE LIMITED WARRANTY IS GIVEN. SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE
EXPRESSED WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED,
ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON WHATSOEVER. ALL
WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED DURING NORMAL WORKING
HOURS. ALL REPLACEMENT PARTS, WHETHER NEW OR REMANUFACTURED, ASSUME AS THEIR
WARRANTY PERIOD ONLY THE REMAINING TIME PERIOD OF THIS WARRANTY.
THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR:
1. Normal maintenance as outlined in the installation and servicing instructions or owner’s
manual, including filter cleaning and/or replacement and lubrication.
2. Damage or repairs required as a consequence of faulty installation, misapplication,
abuse, improper servicing, unauthorized alteration or improper operation.
3. Failure to start due to voltage conditions, blown fuses, open circuit breakers or other
damages due to the inadequacy or interruption of electrical service.
4. Damage as a result of floods, winds, fires, lightning, accidents, corrosive environments or
other conditions beyond the control of the Manufacturer.
5. Parts not supplied or designated by the Manufacturer, or damages resulting from their use.
6. Manufacturer products installed outside the continental U.S.A., Alaska, Hawaii, and
Canada.
7. Electricity or fuel costs or increases in electricity or fuel costs for any reason whatsoever
including additional or unusual use of supplemental electric heat.
8. ANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some states do not allow the exclusion of incidental or
consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which may
vary from state to state.
Page 21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising