st2-xm2 setup and connections

st2-xm2 setup and connections
2
800.967.2346
IMPORTANT SAFEGUARDS
11.Grounding or Polarization - Precaution should be taken so that the
grounding or polarization means of an appliance is not defeated.
12.Power Cord Protection - Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, receptacles,
and the point where they exit from the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER - SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
14.Non-use Periods - The power cord of the appliance should be
unplugged from the outlet when left unused for a long period of time.
15.Object and Liquid Entry - Care should be taken so that objects do not
fall and liquids are not spilled into the enclosure through the openings.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
16.Damage Requiring Service - The appliance should be serviced by qualified service personnel when:
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
B. Objects have fallen, liquid has been spilled into the appliance; or
If you have any questions please call Russound Inc. at
1-800-638-8055 or 603-659-5170.
E. The appliance has been dropped or the enclosure is damaged.
Safety Instructions:
1. Read Instructions - All the safety and operating instructions should be
read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be
retained for future reference.
3. Heed Warnings - All warnings on the appliance in the operating instructions should be adhered to.
4. Follow Instructions - All operating and user instructions should be followed.
5. Water and Moisture - The appliance should not be used near water; for
example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
6. Carts and Stands - The appliance should be used only
with a cart or stand that is recommended by the
manufacturer. An appliance and cart combination
should be moved with care. Quick stops, excessive
force and uneven surfaces may cause the appliance
and cart combination to overturn.
7. Wall or Ceiling Mounting - The appliance should be mounted to a wall
or ceiling only as recommended by the manufacturer.
8. Ventilation - The appliance should be situated so that its location or
position does not interfere with its proper ventilation. For example, the
appliance should not be situated on a bed, sofa, rug, or similar surface
that may block the ventilation openings, or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air
through the ventilation openings.
9. Heat - The appliance should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
10.Power Sources - The appliance should be connected to a power supply
only of the type described in the operating instructions or as marked on
the appliance.
2
13.Cleaning - The appliance should be cleaned only as recommended by
the manufacturer.
A. The power supply cord or the plug has been damaged; or
C. The appliance has been exposed to rain; or
D.The appliance does not appear to operate normally; or
17.Servicing - The user should not attempt to service the appliance beyond
that described in the operating instructions. All other servicing should
be referred to qualified service personnel.
Precautions:
1. Power – WARNING: BEFORE TURNING ON THE POWER FOR THE
FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.
2. Do Not Touch The ST2 With Wet Hands – Do not handle the ST2 or
power cord when your hands are wet or damp. If water or any other liquid enters the ST2 cabinet, unplug the unit from power immediately and
take the ST2 to a qualified service person for inspection.
3. Location of ST2 – Place the ST2 in a well-ventilated location. Take special care to provide plenty of ventilation on all sides of the ST2 especially when it is placed in an audio rack. If ventilation is blocked, the ST2
may overheat and malfunction. Do not expose the ST2 to direct sun
light or heating units as the ST2 internal components temperature may
rise and shorten the life of the components. Avoid damp and dusty
places.
4. Care – From time to time you should wipe off the front and side panels
of the cabinet with a soft cloth. Do not use rough material, thinners,
alcohol or other chemical solvents or cloths since this may damage the
finish or remove the panel lettering.
This device complies with Part 15B of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by
Russound could void the user’s authority to operate this equipment.
TABLE OF CONTENTS
Product Introduction..........................................................................................................4-5
Component Guide
ST2-XM2 Front Panel ...........................................................................................................6
ST2-XM2 Rear Panel............................................................................................................7
ST2-RC Remote Control .......................................................................................................8
ST2-XM2 Setup and Connections
Basic Connections...............................................................................................................9
CAV6.6 Connections..........................................................................................................10
CA Series and ST2-KP Connections ....................................................................................11
Antenna Connections .........................................................................................................12
ST2-XM2 Operation
XM Radio Activation...........................................................................................................13
XM Radio Displays.............................................................................................................13
XM Radio Modes .........................................................................................................14-17
Front Panel Controls ..........................................................................................................18
ST2-RC Remote Control .....................................................................................................19
ST2-KP Keypad Control......................................................................................................20
UNO-S2 Keypad Control with RNET Controller.................................................................21-22
SRC2 Remote Control with RNET Controller....................................................................23-24
ST2-XM2 Tuner Programming
ST2 Chassis Setup Menu ...................................................................................................25
Source Number ....................................................................................................25-26
Update Firmware .......................................................................................................26
Factory Initialization ...................................................................................................26
System Info...............................................................................................................26
Tuner Setup Menu for XM ..................................................................................................28
Memory Name ......................................................................................................28-29
Bank Name ...............................................................................................................30
Controller ID ..............................................................................................................30
Diagnostics ...............................................................................................................30
Factory Initialization ...................................................................................................30
System Info...............................................................................................................30
Backup and Restore .........................................................................................................31
Programming for CAV6.6 Use ............................................................................................32
Programming for CAM6.6 Use ...........................................................................................33
Technical Specifications ....................................................................................................34
Warranty & Repair .............................................................................................................35
3
INTRODUCTION
DESCRIPTION
Thank you for choosing the Russound ST2-XM2
Dual Smart Tuner. Whether you are adding satellite radio to an existing system, expanding a CA
Series system or taking advantage of the CAV6.6
or CAM6.6’s robust RNET® communication link,
the ST2-XM2 Tuner is designed to meet your needs.
The ST2-XM2 Tuner doubles your satellite radio
listening enjoyment with two XM radio modules in
one unit. The XM tuner delivers all the diversity
and choices available to XM radio subscribers.
The two modules share one set of controls and
display on the front of the unit, but each runs
independently. This arrangement allows two different broadcasts at the same time in a multisource, multi-room audio distribution system.
XM satellite radio provides over 100 channels of
music, news sports, comedy, talk and entertainment. Its coast-to-coast coverage, digital quality
sound and many commercial-free music channels
make XM radio the choice for the discriminating
listener.
XM radio is a subscription-based service, and listeners can subscribe by visiting XM on the web
www.xmradio.com or by calling XM’s Listener
Care at 800-967-2346.
In addition to XM satellite access, the ST2-XM2
Tuner can store up to 72 favorites, or memory
presets. These are stored in groups of six called
banks. There are six banks for each tuner. Each
preset and each bank can be given a custom
name of your choice.
The ST2-XM2 Tuner can be controlled from the
front panel or by the dedicated ST2-KP tuner keypad. It can also be controlled by the ST2-RC IR
remote aimed at the tuner’s front panel IR receiver. The ST2-RC IR codes can be learned into any
IR learning remote control for easy system integration. It can also be controlled by IR signals
4
received through the IR connections on the rear
panel from IR repeating system commonly used
in distributed audio systems.
If the ST2-XM2 Tuner is part of an RNET-enabled
system such as the CAV6.6 or CAM6.6, the
tuner can be controlled through an RNET keypad
such as the UNO-S2.
The ST2-XM2 Tuner also has an RS-232 port to
support fully bi-directional integration into wholehouse control systems such as Crestron® and
AMX®.
FEATURES
• Two XM satellite radio modules
• Compact single rack unit chassis
• Six banks of six memory presets each per
tuner (72 total presets) for storing XM
channels
• Custom names for presets and banks
• Two Favorite presets per tuner
• Dedicated IR remote control
• Individual IR direct inputs for each tuner
• Front panel IR receiver
• Supports two ST2-KP optional tuner keypads
• RNET connections send tuner frequency and
control information to UNO keypad display
• RS-232 control and programming
INTRODUCTION
INSTALLATION APPLICATIONS
RNET-enabled System
When the ST2-XM2 Tuner is used with an RNETenabled device such as the CAV6.6 or CAM6.6,
and is connected to it through the Link In or Link
Out port, the tuner will be controlled by the
CAV6.6 or CAM6.6 through the UNO keypad.
Through RNET, tuner information such as Tuner 1
or 2, channel, preset names and XM is displayed
on UNO keypads. An additional RNET device can
be connected to an existing ST2 by using the
Link Out of the first unit into the Link In of the
second unit.
Before using the ST2-XM2 tuner with the
CAV6.6 or CAM6.6, you must assign source
numbers to Tuner 1 and 2 in the ST2 Setup
Menu AND complete the CAV6.6 and
CAM6.6’s Source Setup procedure to identify the tuner as a “Peripheral“ command
type device.
IR-controlled System
CA Series The ST2-XM2 Tuner can be controlled by infrared
commands received through either of the two IR
connections on the rear panel. There are two
unique IR code sets for Tuner 1 and Tuner 2,
which allow each to be controlled independently
from either IR connection. These codes can be
learned from the ST2-RC remote control into the
CAS-RC remote control.
many other manufacturers’ remote controls that
have learning capability for unified control over
the A-V equipment.
Note: Optional ST2-KP keypads can be used to
provide control for the ST2-XM2 Tuner and are
designed to be used with IR-controlled systems.
RS-232 Controlled System
The ST2-XM2 Tuner can be controlled using the
RNET protocol provided via the RS-232 port on
the rear panel. It can also be controlled by any
RS-232-enabled control system (e.g., Crestron,
AMX). Information on RS-232 operation is available to dealers in the Document Center on the
Russound web site, www.russound.com.
BOX CONTENTS
The ST2-XM2 Tuner comes with the parts needed
to setup and operate the component. These
include:
•
•
•
•
•
•
ST2-XM2 Tuner (two XM modules)
ST2-RC remote control
12VDC power supply
XM antenna (2)
RCA audio cable (2)
Rack mount ears
Please call Russound at 800-638-8055 ext. 501
for assistance if parts are missing.
The ST2-XM2 contains two individual tuners,
which makes it act as two sources in the CA system. There are two source audio outputs and two
IR connections - one for each tuner in the ST2XM2. You will need at least one IR link cable
(Russound P/N 09-0508) for these connections.
If you are using an IR-controlled system from
another manufacturer, installation should be similar. The ST2-XM2 IR codes may be learned into
5
COMPONENT GUIDE
ST2-XM2 FRONT PANEL
1
2
3
XM1
64 : The Groove
4
5
6
XM2
7
64 : The Groove
8
9
XM1
XM2
13
6
10
12
11
1
MAIN POWER SWITCH - Turns power on and off
2
POWER ON/OFF LED - Indicates power on or off
3
REMOVABLE COVER LENS - Covers the selection buttons on the tuner
4
BANK SELECT BUTTON - Selects bank 1-6
5
MEMORY SELECT BUTTONS - Sets and selects memory presets 1-6 for each bank
6
IR RECEIVER - Receives IR signal from remote control
7
LCD PANEL - 12-character backlit display shows station, channel, custom names, etc.
8
XM1 and XM2 - Backlit XM tuner selection indicator
9
TNR SEL - Selects Tuner 1 (XM1) or Tuner 2 (XM2), and accesses tuner setup menus
10
BAND - Selects an XM Mode (Category Search, Now Playing, Display Preferences)
Enters menu selections when programming
11
ST/MONO - Press to Exit current XM Mode, hold for signal strength
12
MEM PRESET UP/DOWN - Selects memory presets starting with last preset
Toggles through menu features
13
TUNE UP/DOWN - Manually selects channels (Channel Up/Channel Down)
Toggles through menu settings
COMPONENT GUIDE
ST2-XM2 REAR PANEL
NEWMARKET, NH U.S.A.
3
ST2
INTERFACE
IN
5
Smart Tuner
RS-232
LINK
4
KEYPAD PORTS
ANTENNA
IR
6
7
TUNER 2
AUDIO OUTPUT
L
R
ANTENNA
8
IR
TUNER 1
AUDIO OUTPUT
L
R
9
Serial#
12VDC 1.25A
OUT
XM TUNER 2
10
MADE IN KOREA
2
1
XM TUNER 1
1
RNET LINK IN/LINK OUT - Links to other Russound components that are RNET compatible,
displays frequency and other information on the UNO keypads
2
RS-232 INTERFACE - The RS-232 Interface allows the tuner to be controlled by PC or other devices
that have an RS-232 Interface. The RS-232 Interface also allows for firmware updates and programming (DB9 Cable)
3
KEYPAD PORTS - RJ-45 Keypad ports for ST2-KP tuner keypads in dedicated, non-RNET
systems (Do not connect UNO keypads to these ports)
4
XM ANTENNA - XM Antenna SMB connection (50 ohms) for Tuner 2
5
IR INPUT - IR control input (common IR control) for Tuner 2 or Tuner 1
6
AUDIO OUTPUT - Line-level audio signal outputs (RCA Cable) for Tuner 2
7
XM ANTENNA - XM Antenna SMB connection (50 ohms) for Tuner 1
8
IR INPUT - IR control input (common IR control) for Tuner 1 or Tuner 2
9
AUDIO OUTPUT - Line-level audio signal outputs (RCA Cable) for Tuner 1
10
POWER SUPPLY - 12VDC external power supply connection
7
COMPONENT GUIDE
ST2-RC REMOTE CONTROL
1
1
POWER - Puts the tuner in/out of standby mode
2
TUNER CONTROL - Select TUNER 1 (XM1) or
TUNER 2 (XM2) and all subsequent button presses affect that tuner
2
3
TUNER 1
4
BANK SELECT - Used for direct bank selection
5
TUNE SELECT - Used for direct channel
TUNER 2
(numeric input 1-6)
3
13
1
2
3
4
5
6
7
8
9
MEM
0
12
AM/FM
selection (numeric input)
4
6
TUNE UP/DOWN - Incrementally scrolls through
channel numbers
5
BANK
7
FAV 1/FAV 2 - Sets/Selects Favorite 1 or 2
preset selection on ST2-XM2 tuner
8
SEEK UP/DOWN - Scrolls through banks 1-6
9
OK - Operating mode toggle
6
TUNE
MEM
NUMERIC INPUT - Number buttons for direct
selection of channel, bank, preset
PWR
TUN
7
E
TUNE
10
FAV 2
FAV 1
STEREO/MONO - Exit current XM operating
mode
SEEK
OK
SEEK
11
11
8
LOC/
DX
ST/
MONO
TUNE
12
13
8
MEM UP/DOWN - Scrolls through preset
stations within selected bank
10
9
TUNE UP/DOWN - Scrolls through channel
numbers
MEM SELECT - Used for direct memory select
(numeric input 1-6)
ST2-XM2 SETUP AND CONNECTIONS
BASIC CONNECTIONS
Power
To power the tuner, connect the 12VDC external
power supply by inserting the power supply jack
into the power supply connection on the tuner’s
rear panel.
ST2-KP RJ-45 Connection Wiring
Audio Output
Connect one end of a dual RCA audio cable to
the Tuner 1 Audio Output connection. Keep proper channel identity. Attach the other end of the
RCA cable to the source input of the audio control system. Repeat the same procedure for the
Tuner 2 Audio Output.
IR Connections
The ST2-XM2 Tuner can be controlled by
infrared commands received through the two IR
connections on the rear panel. The ST2-XM2
Tuner component contains two tuners, which
must be set up as two sources. There are two
IR connections - one for each tuner in the
ST2-XM2. You will need two IR link cables
(Russound P/N 09-0508) for these connections.
There is a unique IR code set each for Tuner 1
and Tuner 2, which allow each to be controlled
independently. These codes can be learned from
the ST2-RC remote into learning-capable remote
controls and keypads.
If you are using an IR-controlled system from
another manufacturer, installation should be
similar. The ST2-XM2 IR codes may be learned
into many other manufacturers’ remote controls
that have learning capability for unified control
over the A-V equipment.
RNET Connection
To link the ST2-XM2 to an RNET-compatible
device, use a CAT-5 passthrough patch cable
with similar wiring terminations at each end.
Connect one end of the cable to the RNET Link
In of the ST2 tuner, and connect the other end
of the patch cable to the RNET Link Out connection on the RNET-compatible device.
ST2-KP Keypad to ST2-XM2 Connection
(Non-RNET System)
The ST2-KP connects to the ST2-XM2 tuner with
CAT-5 cable, using an RJ-45 (T568A) jack on the
tuner connection end of the cable. Be sure to
use the keypad ports for the ST2-KP and NOT
the RNET link ports. The ST2-XM2 tuner supports up to two ST2-KP keypads. An SA-ZX3
Keypad Splitter can be used to add additional
keypads.
Note: ST2-KP keypads are designed for use
with IR-controlled systems (non-RNET systems).
When the ST2-XM2 Tuner is a component of an
RNET system such as CAV6.6, the RNET-system
keypads are used.
Rack Mount Installation
The ST2-XM2 can be mounted in a standard
component rack using the rack ears provided.
Line the rack ear’s two rows of screw holes with
the three screw holes on the side of the tuner.
Use the screws provided to secure the rack
ears onto the unit on both sides. The ST2-XM2
tuner should not be installed above a high heatproducing component such as a power amplifier.
9
ST2-XM2 SETUP AND CONNECTIONS
CAV6.6 CONNECTIONS
45:XM Cafe
UNO-S2
keypads
64:The Groove
12VDC 1.25A
CAV6.6
RCA Cable
Source Connections with CAV6.6 Controller/Amplifier (RNET System)
The diagram depicts a typical setup using the ST2-XM2 Tuner with a CAV6.6 amplifier. Each tuner in
the ST2 unit must be connected as a separate source for audio inputs. UNO-S2 keypads are connected to the CAV6.6 keypad ports, NOT the ports on the ST2 Tuner.
10
ST2-XM2 SETUP AND CONNECTIONS
CA SERIES AND ST2-KP CONNECTIONS
RCA Cable
IR Link Cable
Pos (+)
Source
Neg (–)
KPL
ST2-KP
LINK
ST2
Smart Tuner
RS-232
INTERFACE
IN
KEYPAD PORTS
ANTENNA
IR
TUNER 2
AUDIO OUTPUT
L
R
ANTENNA
IR
OUT
IR Link Cable
TUNER 1
AUDIO OUTPUT
L
R
Serial#
12VDC 1.25A
MADE IN KOREA
NEWMARKET, NH U.S.A.
ST2-XM
RCA Cable
CAS44
RCA Cable
Source Connections with CA Series Controller/Amplifier
The diagram depicts a typical setup using the ST2-XM2 Tuner with a CAS44 controller amplifier. Each
tuner in the ST2 unit must be connected as a separate source for audio inputs.
CAT-5 Cable
ST2-KP Connections to ST2-XM2 Tuner (Non-RNET Systems)
The diagram depicts a standard ST2-KP keypad connection to the keypad port on the back of the
ST2-XM2. The keypad uses a 110 punchdown connection and an RJ-45 T568A connection to the tuner.
11
ST2-XM2 SETUP AND CONNECTIONS
ANTENNA CONNECTIONS
XM Antenna
XM Signal Strength Mode
Connect the included XM antenna for XM reception to the back panel of the XM module. The
antenna comes with 20 feet of cable. If this
length is not sufficient, there are aftermarket
antenna kits available for custom lengths.
Position the antenna near a south-facing window
to receive the best signal from a satellite or
terrestrial signal.
To test the XM reception, turn the unit on. When
the XM radio is powered for the first time, the
XM service will start playing XM Channel 1, a
preview/promotional channel. Verify that Channel
1 is playing by pressing the Tune Up/Tune Down
buttons. Enter Signal Strength Mode by pressing
and holding the ST/MONO button on the
ST2-XM2 front panel. The display shows one of
the following:
The antenna may also be attached to an external wall by sliding the slots on the back of the
antenna onto four screws mounted on an exterior wall. Establish the best receiving position for
the antenna before attaching it to the wall.
GOOD SIGNAL Signal strength good
MARGINAL SIG Signal strength marginal
POOR SIGNAL Signal strength poor
NO SIGNAL
Loss of signal
Adjust the antenna until GOOD SIGNAL is displayed. Press ST/MONO to exit Signal Strength
Mode.
ANTENNA
12VDC 1.25A
ST2-XM2 Tuner
12
ST2-XM2 OPERATION
XM RADIO OVERVIEW
XM Radio Activation
XM Radio is over 100 channels of radio broadcasts with the signal delivered by satellite and (depending on location) transferred by terrestrial antennas. The radio is a subscription-based service with a
monthly provider fee and an activation charge. XM radio broadcasts several channels for preview but
will not broadcast the full range of channels without activation. Activation and billing are handled
solely through XM Radio.
To activate the XM tuner:
1 Turn on the power, select the XM Tuner, and select channel 0. The tuner’s eight-character XM
satellite Radio ID number will appear on the display. Write the number down to have it available
when contacting XM Radio for activation. The number is also shown on the back of the unit and
on the product box. Both XM tuners must be activated.
2. To subscribe, have a major credit card and your XM Radio ID number at hand and contact XM at
http://www.xmradio.com/activation. You can also activate service by calling XM Radio at
1-800-967-2346. You will be guided through the activation process step by step.
3. A complete and up-to-date full channel listing is available on the XM Radio website,
www.xmradio.com.
XM Radio Displays
In addition to Channel and Category information, the XM tuner will broadcast operating condition
messages when the following conditions occur:
Display
ANTENNA
UPDATING
LOADING
OFF AIR
CH - - -----------
Condition
Antenna not connected
Updating encryption code
Acquiring channel audio or information
Channel not in service
Channel (SID) no longer available
Corresponding Artist Name or Song Title are null (empty)
No channel available for the chosen category
13
ST2-XM2 OPERATION
XM RADIO MODES
XM Radio Modes
There are four user “modes” for selecting music and viewing music information on the XM Tuner:
Preset (default or normal)
Category Search
Now Playing
Display Preferences.
These modes are accessed through certain button and key presses from the tuner panel, remote
controls and keypads. When choosing modes, if no choice is made after 20 seconds, the tuner will
time out by showing EXIT and return to tuner display and Preset mode.
For all XM Modes
The chart below outlines the button presses for various XM tuner functions outside of the XM modes.
ST2-XM
ST2-RC
ST2-KP
UNO-S2
SRC2
All User Modes
Operating Mode Toggle
OK
Exit Current Mode
ST/
MONO
Signal Strength
Hold
Hold
Hold
Operating Mode Toggle
This button press accesses the three non-default XM modes. The three modes will appear in order:
Category Search, Now Playing and Display Preferences.
Exit Current Mode
This button press returns the XM tuner to Preset (default) mode.
Signal Strength
This button press and hold accesses the Signal Strength mode. Depending on the signal, the following will be displayed:
GOOD SIGNAL Signal strength good
MARGINAL SIG Signal strength marginal
POOR SIGNAL Signal strength poor
NO SIGNAL
Loss of signal
Press the appropriate button again to exit Signal Strength Mode.
14
ST2-XM2 OPERATION
XM RADIO MODES
Preset (default) Mode
This is the normal operating mode of the XM tuner. In this mode the XM tuner operates similarly to an
AM/FM tuner for channel up and down, bank selection and memory presets.
Next Preset
This button press accesses the next saved preset (6 presets for each bank) in the chosen bank.
Previous Preset
This button press accesses the previous saved preset in the chosen bank
Next Bank
This button press accesses the next bank (total of 6 banks).
Previous Bank
This button press accesses the previous bank.
Channel Up
This button press accesses the next active channel up from the current channel.
Channel Down
This button press accesses the next active channel down from the current channel.
ST2-XM
ST2-RC
ST2-KP
UNO-S2
UNO-S1
SRC2
Next Bank
Hold
Hold
Hold
Previous Bank
Hold
Hold
Hold
Preset Mode
Next Preset
MEM
MEM
Previous Preset
Channel Up
Channel Down
TUNE
Hold
TUNE
Hold
15
ST2-XM2 OPERATION
XM RADIO MODES
1.CAT SEARCH)
Category Search Mode (1
XM Radio is organized by Channel Category (e.g., Rock, Country, News). Within each category is
a series of channels (e.g., Top Tracks, Bluegrass Junction, XM Classics). Channel selection in this
mode is refined to scrolling only those channels in the selected category.
Next Category
This button press accesses the next category from the current category.
Previous Category
This button press accesses the previous category from the current category.
Category Channel Up
This button press accesses the next channel up within the selected category.
Category Channel Down
This button press accesses the next channel down within the selected category.
ST2-XM
Category Search Mode
Next Category
ST2-RC
ST2-KP
UNO-S2
UNO-S1
OK
MEM
MEM
Previous Category
Category Channel Up
TUNE
Category Channel Down
16
Hold
TUNE
Hold
SRC2
ST2-XM2 OPERATION
XM RADIO MODES
2.NOW PLAYNG)
Now Playing Mode (2
This mode displays information about the current XM selection. Appropriate button presses access
the next or previous information item.
NAME:
Displays the artist’s name, feature name or program name (news, talk, sports).
TITLE :
Displays the song title or program title.
CATEGORY :
Displays the current category.
ST2-XM
Now Playing Mode
ST2-RC
ST2-KP UNO-S2 UNO-S1
SRC2
OK
Next Info Item
MEM
TUNE
MEM
TUNE
Previous Info Item
3.DSPLY PREF)
Display Preference Mode (3
This mode allows you to choose how XM channel information will be displayed on the keypad and
tuner. Appropriate button presses access the next or previous preference item.
Note: For any display configuration, the artist’s name and song title will scroll before the display
returns to the designated display format.
CH NUMBER:)
Channel Number (C
This selection displays the channel number only (e.g., XM070, XM103).
CH NAME:)
Channel Name (C
This selection displays the channel name only (e.g., ESPN Radio, Real Jazz).
#:CH NAME:)
Channel Number and Name (#
This selection displays the channel number and name (e.g., 64:The Groove, 121:Fox News).
ST2-XM
Display Preference
Mode
Next Display
Preference
Previous Display
Preference
ST2-RC
ST2-KP
UNO-S2
UNO-S1
SRC2
OK
MEM
TUNE
MEM
TUNE
17
ST2-XM2 OPERATION
FRONT PANEL CONTROLS
Front Panel Operation
To turn the unit on, push the On/Off button up on the
front panel. Pushing the On/Off button down turns the
tuner off.
4. Push the desired memory preset (M1 through M6)
button for more than 2 seconds. When the memory
preset is saved, the appropriate preset number (M1
through M6) and SAVED appears on the LCD. The
selected station setting reappears and the sound
resumes after the button is released.
Selecting the desired tuner
Recalling a Memory Preset
From the front panel, use
to toggle between the
XM tuners. A backlight shows behind the selected
label XM1 (green) or XM2 (amber) to indicate the
active tuner. In addition, the LCD panel is also backlit
green for Tuner 1 and amber for Tuner 2. Each time a
tuner is selected the display will refresh with the current station or preset, and all subsequent memory
preset entries will be associated with that selected
tuner.
To recall a memory preset, use
to select the
desired bank, then press the desired preset button
(M1 to M6). In addition to direct selection, the memo-
Turning the unit on
Selecting an XM mode
Push
to select an XM operating mode.
Exiting an XM mode
Push
to exit the XM mode selection menu.
Signal Strength mode
Press and hold
and release. The display shows
the signal strength rating. To exit press
.
Selecting the desired channel
Press and release
and
for manual tuning.
Bank/Memory Presets
Each tuner has six banks of preset memory settings,
and each bank holds six presets for a total of 36 possible presets for each tuner (72 total presets).
Presets are associated with the tuner that is selected
at the time the preset is saved.
Memory Preset programming
From the front panel, perform these steps:
1. Select a tuner using
2. Use
.
to choose from one of six banks (1-6).
3. Tune to the desired channel.
18
ry presets can be accessed by using
and
scroll through all presets for the bank selected.
to
Backup and Restore
Once all of the tuner settings are completed, it may
be advisable to create a backup of the programmed
settings for future use. The backup will then be available in case tuner settings need to be restored. The
“RNET Backup Utility” is available through the
Document Center at www.russound.com. Also
required are a DB9 male-to-female cable and laptop
or desktop PC.
ST2-XM2 OPERATION
ST2-RC REMOTE CONTROL
ST2-RC Remote Control Operation
number (1 to 6). The memory presets can also be
The ST2-RC remote control is the only means of
remote operation of the ST2-XM2 in a non--RNET system. The ST2-XM2 front panel displays information for
the tuner that is receiving commands from the ST2RC. However, the ST2-RC commands do not change
which tuner is playing; that is done through the system’s source selection.
accessed by using
and
presets for the selected bank.
MEM
To switch the ST2 tuner in or out of standby mode,
push
TUNER 2.
to scroll through all
Saving Favorites
The remote control stores two “favorites” (similar to
memory presets) per tuner. These are set simply by
selecting either Tuner 1 or Tuner 2, setting the
desired frequency and pressing and holding
Turning the unit on/off
PWR
MEM
or any other button except TUNER 1 or
FAV 1
or
FAV 2
until “FAV1 (2) saved” appears on the tuner.
Stored Favorites are then recalled by pressing either
FAV 1
or
FAV 2
.
Selecting the desired tuner
TUNER 1
TUNER 2
To control a tuner, push
or
. When
pressed, these buttons will be backlit green for Tuner
1 (XM1) and amber for Tuner 2 (XM2). Each time a
tuner is selected the display will refresh with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will
be associated with that selected tuner.
Selecting the desired channel
TUNE
Use
and
for manual tuning. To move quickly
through the channels, press and hold either of the
Tune buttons for more than 1.5 seconds.
TUNE
TUNE
To directly select a channel, press
, and enter
the two- or three-digit XM channel number.
Selecting an XM mode
Push
OK
to select an XM operating mode.
Exiting an XM mode
Push
menu.
ST/
MONO
to exit the XM operating mode selection
Recalling a Memory Preset
To recall a memory preset, select the desired tuner,
press
BANK
and enter the desired bank number
(1-6), then press
MEM
and enter the desired preset
19
ST2-XM2 OPERATION
ST2-KP KEYPAD CONTROL
ST2-KP Keypad Operation
1
4
Turning the keypad on/off
To activate the ST2-KP, press
. Press
to
power down the keypad display. The keypad remains
powered until the ST2-XM2 Tuner is turned off.
1
Selecting the desired tuner
Recalling a Memory Preset
To recall a memory preset, press and release
to scroll through the presets for the selected
bank. (Memory presets must be stored for ST2-KP
recall)
5
To select a different tuner, press and hold
. (If the
keypad has been hardware jumper-selected to Tuner
1 or Tuner 2, it will not switch between the two
tuners.) The backlight color of the display will be
green for Tuner 1 (XM1) and amber for Tuner 2
(XM2). Each time a tuner is selected the display will
refresh with the current station or preset for that
tuner, and all subsequent button presses and memory preset entries will be associated with that selected
tuner.
2
Push
2
ST2-KP Keypad Display
The 5-character backlit display shows XM channel
and mode information. Messages scroll twice, then
display the first 5 characters.
ST2-KP Keypad-Front Panel
Selecting an XM mode
to select an XM operating mode.
Exiting an XM mode
XM054
Press and release
until EXIT is displayed to exit
the XM operating mode menu.
3
or
5
3
Selecting the desired channel
2
Use
and
for manual tuning. To move quickly
through the channels, press and hold either
for more than 1.5 seconds.
4
Selecting a Bank
To select a bank, select the desired tuner, then press
and hold
or
to select the desired bank. The
bank name will show on the display.
20
3
or
4
1
ST2-XM2 OPERATION
UNO-S2 KEYPAD CONTROL WITH RNET CONTROLLER
UNO-S2 Keypad Operation
Signal Strength Mode (XM)
NOTE: To control the ST2 Tuner through the
UNO-S2 keypad, the tuner must be configured
as a source using the controller’s programming
steps.
To check XM signal strength, press and hold
Turning the unit on
Selecting a Bank
The tuner is power managed by the RNETenabled controller. If the tuner is in standby
mode, any button press of the UNO-S2 keypad
will bring the tuner out of standby mode.
To select a bank, press and hold
Selecting the desired tuner
to select
either Tuner 1 (XM1) or Tuner 2 (XM2) by choosing the source name/number associated with
Tuner 1 or 2.
up or
again.
for bank
for bank down. The bank’s name will
be temporarily displayed on the UNO-S2.
Press
and
to scroll through the memo-
ry presets for the selected bank. This procedure
will step through all of the presets in the current
bank, then loop back to start at the first one.
Selecting an XM Mode
Only configured presets will be displayed.
to toggle between XM modes.
Exiting an XM Mode
Press and release
strength rating. To exit, press
Recalling a Memory Preset
On the UNO-S2 keypad, press
Push
then release. The display shows the signal
Mute
Press
to mute/unmute the tuner audio output.
until EXIT is displayed to
exit XM mode selection menu.
Selecting the desired channel
Use
and
for manual channel selection.
The channel will appear on the keypad and the
active tuner. To move quickly through the channels, press and hold either
or
for more
than 1.5 seconds.
21
ST2-XM2 OPERATION
UNO-S2 KEYPAD CONTROL WITH RNET CONTROLLER
1
6
5
2
4
3
1
2
22
TUNER SELECTION - Select source
name/number associated with TUNER 1
(XM1) or TUNER 2 (XM2)
TUNE UP/DOWN - Used for manual channel
selection
3
SELECT - XM Operating mode toggle
4
SEEK - (press) Exit current XM mode
4
SCAN - (press and hold) XM Signal Strength
mode toggle
5
MUTE - Mutes/unmutes tuner audio output
6
BANK SELECT - Used for bank selection
(press and hold)
6
MEM UP/DOWN - Scrolls through memory
preset stations (press)
NOTE: UNO-S2 keypads are connected to
the controller to control the ST2-XM2 through
RNET. UNO-S2 keypads do not connect
directly to the ST2 Tuner.
ST2-XM2 OPERATION
SRC2 REMOTE CONTROL WITH RNET CONTROLLER
SRC2 Remote Control Operation
Turning the unit on
Selecting a Bank
The tuner is power managed by the CAV6.6 or
other RNET-enabled controller. If the tuner is in
standby mode, any button press of the SRC2
will bring the tuner out of standby mode when
used with the UNO keypad.
Selecting the desired tuner
To select a tuner, push
To select a bank, press and hold
or
for bank down.
Recalling a Memory Preset
Press
and choose the source
name/number associated with Tuner 1 (XM1) or
Tuner 2 (XM2), or use the numeric source inputs at
for bank up
and
to scroll through a loop of
all the memory presets for the currently selected
bank. Only configured presets will be displayed.
Mute
the bottom of the SRC2.
Press the
Selecting an XM Mode
Push
,
, or
button to mute/unmute the tuner
audio output.
to toggle between XM
operating modes.
Exiting an XM Mode
Press
to exit XM operating mode menu.
Signal Strength mode
Press and hold
and release. The display shows
the signal strength rating. To exit press
.
Selecting the desired channel
Use the Channel
and
or
and
for manual tuning. To move quickly through the
channels, press and hold the button for more than
1.5 seconds. To directly select a channel, enter the
three- or four-digit channel number.
23
ST2-XM2 OPERATION
SRC2 REMOTE CONTROL WITH RNET CONTROLLER
RUSSOUND SELECTION - “R” must be
the selected source for control of the
controller and any connected components. Select “R” before sending
SRC2 remote commands.
1
1
POWER - Powers off zone
2
NUMERIC INPUT - Number buttons for direct
input of channel (press). Memory preset save
(press and hold)
3
LAST - Recalls last XM channel selected
4
INFO - XM Now Playing mode toggle
5
TUNE UP/DOWN - Incrementally scrolls through
channels
6
OK - XM Operating mode toggle
7
EXIT - Exit XM Operating mode
8
PLAY - XM Operating mode toggle
9
STOP - Exit XM Operating mode
2
11
3
10 MEM UP/DOWN - Scrolls through memory pre-
16
sets for selected bank (press)
4
10 BANK UP/DOWN - Used for bank selection (press
15
5
6
14
13
5
7
8
12
9
and hold)
11 TUNER SELECTION - Select XM Tuner by its asso-
ciated source name/number
12 PAUSE - Mutes/unmutes tuner audio output
13 GUIDE - XM Category Search mode toggle
14 SEEK UP/DOWN - Next/previous preset,
category, info item, display preference
10
15 MENU - XM Operating mode toggle
11
16 TUNE UP/DOWN - Incrementally scrolls through
channels
24
ST2-XM2 TUNER PROGRAMMING
ST2 TUNER SETUP MENU
ST2-XM2 Tuner Setup Menus
Note: The Setup Menu procedures must be performed from the ST2-XM2 Tuner front panel.
The ST2-XM2 Tuner Setup Menus provide setup and naming procedures for the ST2-XM2 main chassis and the XM tuner modules. These procedures include source number assignments, assigning a
custom name to a memory preset or a bank, factory initialization and system information.
If the ST2-XM2 is used with a non-RNET system, the ST2-XM2 can be connected and operated without any setup programming. Follow the setup menus if custom names are desired, or for system
info.
If the ST2-XM2 is used with an RNET system such as CAV6.6 or CAM6.6, the following minimum
setup must be performed for the ST2-XM2 to be properly controlled by the CAV6.6 and CAM6.6.
1. ST2 Chassis Setup Menu - Assign source numbers to Tuner 1 and Tuner 2.
2. CAV6.6/CAM6.6 Source Setup Menu - Configure the source numbers assigned in step 1 for
Tuners 1 and 2, and assign command type PERIPHERAL.
NOTE: Once the programming procedures are completed, cycle power first to the Tuner and then to
the CAV6.6/CAM6.6 (must be powered on last) to establish a connection.
ST2 Chassis Setup Menu
Source Number (Chassis)
The Source Number procedure permits Tuner 1
(XM1) and Tuner 2 (XM2) to be assigned the
proper source numbers to be used in an RNET
system.
Note: The source number must be assigned as
PERIPHERAL in the RNET controllers.
Note: Each of the ST2-XM2 modules can be configured as source number “unassigned” if the
module is used in another system (e.g., home
theater) or will not be used as a source in the
RNET system.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press MEM Up/Down
until SOURCE NUM appears on the tuner.
3. Press BAND. TUNER # appears.
4. Press the Tune Up/Down buttons to select the
Tuner # (Tuner 1 is XM1, Tuner 2 is XM2).
5. Press BAND. SOURCE NUM appears.
6. Press the Tune Up/Down buttons to scroll
through the source numbers 1-6.
7. Press BAND to select the source number.
8. Repeat the process for the next tuner.
9. Press TNR SEL to exit the Source Number
menu.
(continued)
25
ST2-XM2 TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Update Firmware (Chassis)
The Update Firmware procedure allows the ST2
tuner’s OS firmware to be updated. The procedure is performed using a DB9 serial cable with
one end connected to the RS-232 port on the
back of the tuner and the other connected to a
PC or laptop. If an OS firmware update is available, it can be obtained through the Document
Center at www.russound.com. XM tuner module
firmware update must be performed by an
authorized Russound service facility.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press MEM Up/Down
until UPDATE FIRMW appears on the tuner.
3. Press BAND to enter the UPDATE FIRMW menu.
4. “Hold BAND” appears on the tuner.
5. While pressing and holding BAND, “After
update cycle power” appears on the tuner
display.
6. When “Start Update” appears on the tuner display, start the update program. “Finished” will
then appear in firmware’s update window on the PC.
7. Cycle power to the tuner.
Factory Initialization (Chassis)
The Factory Initialization procedure allows the
erasure of all programmed settings and returns
them to the factory default settings.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
26
2. TUNER SETUP appears. Press MEM Up/Down
until FACTORY INIT appears on the tuner.
3. Press BAND to enter the FACTORY INIT menu.
4. “Are you sure” appears on the tuner. Using the
Tune Up/Down buttons, view the “Yes” and “No”
selections.
5. Press BAND to select. A “No” selection
returns to the top of the Factory Init menu. A
“Yes” begins the initialization.
6. “Please wait” appears on the tuner during the
process and “Cycle Power” appears when complete.
7. Cycle power on the ST2-XM2 tuner.
System Info (Chassis)
The System Info menu shows the ST2 Tuner’s
manufacturing build properties.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press MEM Up/Down
until SYSTEM INFO appears on the tuner.
3. Press BAND.
4. Press BAND at “Build Time” to view.
5. Press MEM Up/Down to advance.
6. Press BAND at “Build Date” to view.
7. Press MEM Up/Down to advance.
8. Press BAND at “Version” to view.
9. Press TNR SEL to exit the System Info menu.
(END OF ST2 CHASSIS SETUP)
ST2-XM2 TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Press and Hold
TNR SEL button
TNR
SEL
ST2 Chassis Setup Procedures
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
UPDATE
FIRMW
Procedure
FACTORY
INIT
Procedure
TNR
SEL
TUNER
#
SYSTEM
INFO
Procedure
Chassis
Setup
Menu
TNR
SEL
HOLD
BAND
This
Procedure
returns the
ST2 Tuner
to its
Factory
settings
After update
cycle Power
Are you sure
SOURCE
NUM
Start
Update
YES
NO
Cycle Power
Please wait
Cycle Power
27
ST2-XM2 TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Tuner Setup Menu for XM
Memory Name
A memory preset must be created and saved
before it can be named (see page 18). Once it is
XM Setup Menu
Memory Name Procedure
Press TNR SEL
button to select
XM Tuner
TNR
SEL
saved, the preset’s Tuner #, Bank # and Memory
# must be entered in the following procedure.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND again.
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
UPDATE
FIRMW
Procedure
BANK
NAME
Procedure
CONTROLLR
ID
Procedure
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
Chassis
Setup
Menu
TNR
SEL
MEM
NAME
Procedure
DIAGNOSTICS
Procedure
TNR
SEL
BANK #
MEMORY #
MEMORY
NAME
Selects
character
Selects
character
position
Repeat
for each
character
in name
28
SAVE
CHANGES?
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
XM
Setup
Menu
ST2-XM2 TUNER PROGRAMMING
ST2 TUNER SETUP MENU
3. MEMORY NAME appears on the tuner.
4. Press BAND.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
7. Press BAND to advance. Memory # appears.
8. Press the Tune Up/Down buttons to select a
Memory #.
9. Press BAND to advance. MEMORY NAME
appears again.
10. Press BAND to access the Memory Name
entry screen.
XM Setup Menu
Bank Name Procedure
Press TNR SEL
button to select
XM Tuner
TNR
SEL
11. Press Tune Up/Down to select a character
and MEM Up/Down to change a character
position. Up to 12 characters can be entered
one by one. A blinking cursor indicates the placement of the character being entered.
12. Press BAND when memory name is entered.
13. SAVE CHANGES will appear.
14. Press Tune Up/Down to select Yes or No.
15. Press BAND to save memory name. The
Memory Name menu returns to the Memory #
prompt to name other presets, or press TNR
SEL to return to the Memory Name menu start.
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
UPDATE
FIRMW
Procedure
BANK
NAME
Procedure
CONTROLLR
ID
Procedure
DIAGNOSTICS
Procedure
BANK
NAME
SAVE
CHANGES?
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
Chassis
Setup
Menu
TNR
SEL
MEM
NAME
Procedure
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
XM
Setup
Menu
TNR
SEL
BANK #
Selects
character
Selects
character
position
Repeat
for each
character
in name
29
ST2-XM2 TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Bank Name
Factory Initialization
A custom name can be assigned to each of the
six banks of Tuner 1 (XM).
The Factory Initialization procedure allows the
erasure of all programmed settings of the XM
tuner and returns them to the factory default settings.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until BANK NAME appears on the tuner.
4. Press BAND.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
7. Press BAND. BANK NAME appears again.
8. Press BAND to access the Bank Name entry
screen.
9. Press Tune Up/Down to select a character
and MEM Up/Down to change a character position. Up to 12 characters can be entered one by
one. A blinking cursor indicates the placement of
the character being entered.
10. Press BAND when bank name is entered.
11. SAVE CHANGES will appear.
12. Press Tune Up/Down to select Yes or No.
13. Press BAND to save bank name. The Bank
Name menu returns to the Bank # prompt to
name other banks, or press TNR SEL to exit the
Bank Name menu.
System Info
Diagnostics
The System Info menu shows the ST2 Tuner’s
manufacturing build properties.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press MEM Up/Down
until SYSTEM INFO appears on the tuner.
3. Press BAND.
4. Press BAND at “Build Time” to view.
5. Press MEM Up/Down to advance.
6. Press BAND at “Build Date” to view.
7. Press MEM Up/Down to advance.
8. Press BAND at “Version” to view.
9. Press TNR SEL to exit the System Info menu.
The Diagnostics procedure is for factory
use only.
(END OF XM TUNER SETUP)
Controller ID
The Controller ID procedure is used to identify
the controller(s) that the XM tuner will
respond to.
Note: For the XM module that is installed in the
ST2-XM chassis, “All Controllers” will be the
default setting.
30
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until FACTORY INIT appears on the
tuner.
4. Press BAND to enter the FACTORY INIT menu.
5. “Are you sure” appears on the tuner. Using the
Tune Up/Down buttons, view the “Yes” and “No”
selections.
6. Press BAND to select. A “No” selection
returns to the top of the Factory Init menu. A
“Yes” begins the initialization.
7. “Please wait” appears on the tuner during the
process and “Cycle Power” appears when complete.
8. Cycle power on the ST2-XM tuner.
ST2-XM2 TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Backup and Restore
Once all of the tuner settings are completed, it
may be advisable to create a backup of the programmed settings for future use. The backup will
then be available in case tuner settings need to
be restored.
Press TNR SEL
button to select
XM Tuner
TNR
SEL
The backup and restore PC application “RNET
Backup” is available through the Document
Center at www.russound.com. Also required are
a DB9 male-to-female cable and laptop or desktop PC.
XM Setup Menu
Controller, Diagnostics, Factory Initialization
and System Info Procedures
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
UPDATE
FIRMW
Procedure
BANK
NAME
Procedure
CONTROLLR
ID
Procedure
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
Chassis
Setup
Menu
TNR
SEL
MEM
NAME
Procedure
DIAGNOSTICS
Procedure
SYSTEM
INFO
Procedure
FACTORY
INIT
Procedure
XM
Setup
Menu
TNR
SEL
All Contrlrs
This
Procedure
is for
Factory
use
ONLY
This
Procedure
returns the
ST2 Tuner
to its
Factory
settings
Are you
sure?
Yes or No
YES
NO
Please
Wait
Cycle Power
31
ST2-XM2 TUNER PROGRAMMING
PROGRAMMING FOR CAV6.6 USE
To Program the CAV6.6 to operate with the ST2-XM2 Tuner:
(refer to the CAV6.6 Instruction Manual for details)
1. Enter the Setup Menu by pressing the Setup button on the side of the UNO-S2 keypad.
2. SOURCE SETUP will appear. Enter the Source Setup Menu by pressing the Play button on the
UNO-S2 keypad.
3. BASIC SETUP will appear. Enter the Basic Setup Menu by pressing the Play button again.
4. SOURCE NUM will appear. Use + and - buttons to select the source number to which Tuner 1 (XM)
is connected. Press the Play button to enter your choice.
5. SOURCE NAME will appear. Use + and - buttons to select the name for the source (e.g., Tuner 1
or XM). Press the Play button to enter your choice.
6. COMMAND TYPE will appear. Select PERIPHERAL from the list. Press the Play button to enter this
choice.
7. SAVE CHANGES? appears. Select “Yes” and press the Play button to save changes.
8. SOURCE NUM appears again. Repeat steps 4 through 7 to configure the second tuner.
9. Press the Setup button three times to back out of the Installation Menu.
Source Configuration Note:
When the ST2-XM2 Tuner is used with the CAV6.6 or other RNET controller, it is configured as an
RNET command type “Peripheral” and is connected via the RNET bus. This makes the tuner behave
as a fully integrated device with UNO-S2 keypad support. Each tuner must be set up with a unique
source number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus.
Key Function Note:
When using the tuner with the CAV6.6-S2 system, do not reassign keypad and remote buttons for
tuner control in the CAV6.6 Key Configuration Menu. When the tuner is assigned the “Peripheral” command type in the CAV6.6 Setup Menu, key assignments and functions are automatically assigned and
will operate as shown in the preceding UNO-S2 keypad and SRC2 remote control diagrams.
32
ST2-XM2 TUNER PROGRAMMING
PROGRAMMING FOR CAM6.6 USE
To Program the CAM6.6 (with no internal tuner) to operate with the ST2-XM2 Tuner:
(refer to the CAM6.6 Instruction Manual for details)
1. Enter the Setup Menu by pressing the Setup button on the side of the UNO-S1/S2 keypad.
2. PERIPH SETUP appears. Press the Next button to see SOURCE SETUP. Enter the Source Setup
Menu by pressing the Next button on the UNO-S1 keypad.
3. BASIC SETUP will appear. Enter the Basic Setup Menu by pressing the Next button again.
4. SOURCE NUM will appear. Use Volume Up and Volume Down buttons to select the source number
to which Tuner 1 (XM) is connected. Press the Power button to enter your choice.
5. SOURCE NAME will appear. Use Volume Up and Volume Down buttons to select the name for the
source (e.g., Tuner 1 or XM). Press the Power button to enter your choice.
6. COMMAND TYPE will appear. Select PERIPHERAL from the list. Press the Power button to enter
this choice.
7. SAVE CHANGES? appears. Select “Yes” and press the Power button to save changes.
8. SOURCE NUM appears again. Repeat steps 4 through 7 to configure the second tuner.
9. Press the Setup button three times to back out of the Installation Menu.
To Program the CAM6.6 (with internal tuner) to operate with the ST2-XM2 Tuner:
(refer to the CAM6.6 Instruction Manual for details)
When the CAM6.6 has an internal tuner installed in the Source 1 position, use sources 2 through 6
for the ST2-XM2.
Source Configuration Note:
When the ST2-XM2 Tuner is used with the CAM6.6 or other RNET controller, it is configured as an
RNET command type “Peripheral” and is connected via the RNET bus. This makes the tuner behave
as a fully integrated device with UNO keypad support. Each tuner must be set up with a unique
source number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus.
Key Function Note:
When using the tuner with the CAM6.6 system, do not reassign keypad and remote buttons for tuner
control in the CAM6.6 Key Configuration Menu. When the tuner is assigned the “Peripheral” command
type in the CAM6.6 Setup Menu, key assignments and functions are automatically assigned and will
operate as shown in the preceding UNO-S2 keypad and SRC2 remote diagrams.
33
TECHNICAL SPECIFICATIONS
ST2-XM2 Smart Tuner
Dimensions:
17"W x 8"D x 1.8"H (43 x 20.3 x 4.4 cm)
Weight:
7 lbs. (3.2kg)
Power Supply:
12VDC 1.25A
XM Band:
XM Antenna:
2332.5 - 2345 MHz
50-ohm SMB connection
It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology
incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE®
voice compression software included in this product is protected by intellectual property rights
including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this
or any other software contained in an XM radio is explicitly prohibited from attempting to copy,
decompile, reverse engineer, or disassemble the object code, or in any way convert the object code
into human-readable form. The software is licensed solely for use within this product.
34
WARRANTY & REPAIR
The Russound ST2-XM2 is fully guaranteed against all defects in materials and workmanship for two
(2) years from the date of purchase. During this period, Russound will replace any defective parts and
correct any defect in workmanship without charge for either parts or labor.
For this warranty to apply, the unit must be installed and used according to its written instructions. If
service is necessary, it must be performed by Russound. The unit must be returned to Russound at
the owner's expense and with prior written permission. Accidental damage and shipping damage are
not considered defects, nor is damage resulting from abuse or from servicing by an agency or person not specifically authorized in writing by Russound.
This Warranty does not cover:
• Damage caused by abuse, accident, misuse, negligence,
or improper installation or operation
• Power surges and lightning strikes
• Normal wear and maintenance
• Products that have been altered or modified
• Any product whose identifying number, decal, serial number, etc.
has been altered, defaced or removed
Russound sells products only through authorized Dealers and Distributors to ensure that customers
obtain proper support and service. Any Russound product purchased from an unauthorized dealer or
other source, including retailers, mail order sellers and online sellers will not be honored or serviced
under existing Russound warranty policy. Any sale of products by an unauthorized source or other
manner not authorized by Russound shall void the warranty on the applicable product.
Damage to or destruction of components due to application of excessive power voids the warranty on
those parts. In these cases, repairs will be made on the basis of the retail value of the parts and
labor. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with
a note explaining the nature of service required. Be sure to pack the unit in a corrugated container
with at least three (3) inches of resilient material to protect the unit from damage in transit.
Before returning a unit for repair, call Russound at (603) 659-5170 for a Return Authorization number.
Write this number on the shipping label and ship to:
Russound
ATTN: Service
5 Forbes Road
Newmarket, NH 03857
Due to continual efforts to improve product quality as new technology and techniques become available, Russound/FMP, Inc. reserves the right to revise system specifications without notice.
35
2
Russound
5 Forbes Road, Newmarket, NH 03857
tel 603.659.5170 • fax 603.659.5388
e-mail: tech@russound.com
www.russound.com
E. & O.E.
Copyright © 2006 Russound® All rights reserved.
All trademarks are property of their respective owners.
28-1170
Rev. 1 02/07/06
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising