User Manual-SPE-100-ENGLISH_Web

User Manual-SPE-100-ENGLISH_Web
NETWORK VIDEO ENCODER
User Manual
SPE-100
Network Video Encoder
User Manual
Copyright
©2014 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall
be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no
formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own
responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
 Design and specifications are subject to change without prior notice.
 The initial administrator ID is “admin” and the password should be set when logging in for the first time.
Please change your password every three months to safely protect personal information and to prevent
the damage of the information theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by
mismanaging a password.
overview
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
● OVERVIEW
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety, If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. This product is intended to be supplied by a Listed power supply unit marked “Class 2”
and rated from 12 V dc, min 1.5A.
English _3
overview
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PROCUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.
4_ overview
Class construction
An apparatus with CLASS construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
Batteries(battery pack or batteries installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
CALIFORNIA USA ONLY
This Perchlorate warning applies only to primary CR (Manganese Dioxide)
Lithium coin cells in the product sold or distributed ONLY in California USA.
“Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/
hazardouswaste/perchlorate.”
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
Please use the input power with just one encoder and other devices must not
be connected.
English _5
● OVERVIEW
Battery
overview
Please read the following recommend safety precautions carefully.
 Do not Place this apparatus on an uneven surface.
 Do not install on a surface where it is exposed to direct sunlight, near
heating equipment or heavy cold area.
 Do not place this apparatus near conductive material.
 Do not attempt to service this apparatus yourself.
 Do not place a glass of water on the product.
 Do not install near any magnetic sources.
 Do not block any ventilation openings.
 Do not place heavy items on the product.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.
 Reference : In case of providing information for helping of product’s usages
 Notice : If there’s any possibility to occur any damages for the goods and
human caused by not following the instruction
 Please read this manual for the safety before using of goods and keep it in
the safe place.
6_ overview
CONTENTS
OVERVIEW
10
11
INSTALLATION &
CONNECTION
14
14
15
16
NETWORK CONNECTION
AND SETUP
21
21
22
23
24
25
26
29
30
32
32
Important Safety Instructions
Product Features
Recommended PC Specifications
Recommended SD/SDHC
Memory Card Specifications
What’s Included
At a Glance
Inserting/Removing a SD Memory
Card
Memory Card Information
(Not Included)
Connecting with other Device
Connecting the Network video
encoder Directly to Local Area
Networking
Connecting the Network video
encoder Directly to a DHCP
Based DSL/Cable Modem
Connecting the Network Video
Encoder Directly to a PPPoE
Modem
Connecting the Network video
encoder to a broadband router
with the PPPoE/Cable Modem
Buttons used in IP Installer
Static IP Setup
Dynamic IP Setup
Port Range Forward (Port Mapping)
Setup
Connecting to the Network
Device from a Shared Local PC
Connecting to the Network video
encoder from a Remote PC via
the Internet
English _7
● OVERVIEW
3
3
9
9
10
overview
WEB VIEWER
33
33
35
35
36
40
42
45
Connecting to the Network video
encoder
Password setting
Login
Installing Silverlight Runtime
Installing STW WebViewer Plugin
Using the Live Screen
Playing the recorded video
SETUP SCREEN
51
51
58
68
80
Setup
Video & Audio Setup
Network Setup
Event Setup
System Setup
88
90
91
93
Specification
Product Overview
Troubleshooting
Open Source License Notification
On The Product
51
APPENDIX
88
8_ overview
PRODUCT FEATURES
M
 However, MPEG-4 video can not be played on a web page. Use CMS software if you want to play
the video on a web page.
 Support various communication protocols
 Web Browser-based Monitoring
Using the Internet web browser to display the image in a local network environment.
 Alarm
If an event occurs, the event-related video will be transferred to the FTP/email specified by
the user or saved to the SD memory, or the event signal will be sent to the ALARM OUT
port.
 ONVIF Compliance
This product supports ONVIF.
For more information, refer to www.onvif.org.
RECOMMENDED PC SPECIFICATIONS
 CPU : Intel Core 2 Duo 2.4 GHz or higher
 Web Plug-in is optimized to SSE 4.1 Instruction Set.




Operating System : Windows XP, VISTA, 7, Mac OS X 10.7 or higher
Resolution : 1280X1024 pixels or higher (32 bit color)
RAM : 2GB or higher
Web Browser : Internet Explorer 7.0 or higher, Firefox 9.0 or higher, Chrome 15.0 or higher,
*Safari 5.1 or higher
 Neither a beta test version unlike the version released in the company website nor the developer version will
be supported.
 For IPv6 connection, Window 7 or higher is recommended.
 For Mac OS X, only the Safari browser is supported.
 Video Memory : 256MB or higher
J
 If the driver of the video graphic adapter is not installed properly or is not the latest version, the
video may not be played properly.
 For a multi-monitoring system involving at least 2 monitors, the playback performance can be
deteriorated depending on the system.
English _9
● OVERVIEW
 Multi-Streaming
This network video encoder can display videos in different resolutions and qualities
simultaneously using different CODECs.
overview
RECOMMENDED SD/SDHC MEMORY CARD
SPECIFICATIONS
 4GB ~ 32GB
 For your network video encoder, we recommend you use a memory card from the
following manufacturers : SD/SDHC Memory Card : Sandisk, Transcend
 It is recommended you use a memory card that supports at least Class 6.
WHAT’S INCLUDED
Please check if your network video encoder and accessories are all included in the product package.
Appearance
10_ overview
Item Name
Quantity
Description
Network Video Encoder
1
Instruction book,
Installation CD
1
User manual, Quick Guide,
IP Installer S/W Program
CMS S/W DVD
1
NET-i viewer S/W Program
Quick Guide
(Optional)
1
Warranty card
(Optional)
1
ASSY-Tapping Screw
4
Used for installation on the wall or ceiling
AT A GLANCE
Front Side
● OVERVIEW
b
Item
c Description
AUDIO IN
Audio input terminal which brings sound to the network video encoder.
Used to connect the microphone.
b
AUDIO OUT
Audio output terminal which outputs sound from the network video encoder.
Used to connect the speaker.
c
VIDEO IN
Used to connect the BNC video input signal.
LOOP OUT
Used to monitor the BNC video signal.
English _11
overview
Rear Side
6'&$5'
(7+(51(73R(
b
6'
5(6(7
32:(5
c
''6*1&&012
'&9
566(16255(/$<287
Item
Description
SD Memory Card
Compartment
Compartment for the SD memory card.
b
Network Port
Used to connect a PoE or Ethernet cable.
c
Reset Button
Hold it down for 5 seconds to return all your settings to the factory default.
I/O Port
12_ overview
D+
RS-485 Data Line
D-
RS-485 Data Line
S1
Alarm In
G
GND
NC
Alarm Out (for Normal Close)
CM
Alarm Out (Common)
NO
Alarm Out (for Normal Open)
Item
Power Port
Description
Used to connect the specified power source.
SD
Flashing : Failed to record, insufficient space, or inserted
abnormally.
OFF : Network Video Encoder is off, network video
encoder is restarting, memory card is not in place,
When record is off.
SD,
Power Indicators
POWER
ON : While the power is on.
OFF : If the power is off.
English _13
● OVERVIEW
ON : A memory card is inserted and operates normally.
installation & connection
INSERTING/REMOVING A SD MEMORY CARD
Inserting a SD Memory Card
Push the SD memory card in the direction of the arrow shown in the diagram.
J
 Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the
SD memory card.
Removing a SD Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to
eject the memory card from the slot.
J
 Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from
the slot when released.
 To pull out the SD memory card, turn off the encoder power or set the device to <Off> of
<Storage> and press the [Apply (
)] button. (page 69)
 If you turn off the encoder or remove the SD memory card that contains data from the product,
the data may be lost or damaged.
 If the SD memory is inserted and when record is on, the SD LED indicator on the rear of the
network video encoder will turn on.
 If there occurs a problem in the SD memory, the SD LED indicator will blink.
14_ installation & connection
MEMORY CARD INFORMATION (NOT INCLUDED)
What is a memory card?
Selecting a memory card that’s suitable for you
Your network video encoder supports SD/SDHC memory cards.
You may, however, experience compatibility issues depending on the model and make of
the memory card.
For your network video encoder, we recommend you use a memory card from the
following manufacturers : SD/SDHC Memory Card : Sandisk, Transcend
It is recommended you use a memory card that supports at least Class 6.
Playback performance can be affected depending on the speed of memory card, so use
the high-speed memory card.
Memory Card Use
SD and SDHC memory cards feature a switch that disables writing data on to the media.
Having this switch to the Lock position will prevent accidental deletion of data stored in the
memory card but at the same time will also prevent you from writing data on to the media.
Memory Card Components
Contacts
Lock Switch
SD/SDHC
English _15
● INSTALLATION & CONNECTION
The memory card is an external data storage device that has been developed to offer an
entirely new way to record and share video, audio, and text data using digital devices.
installation & connection
CONNECTING WITH OTHER DEVICE
Connecting to the monitor
Connect the [LOOP OUT] port of the network video encoder to the video input port of the
monitor.
M
 In the initial installation of the network video encoder, you can connect the network video encoder
to the monitor for checking the connection status.
 LOOP OUT is provided for output test monitoring.
Connecting the camera
Connect the [VIDEO IN] port of the network video encoder to the video output port of the
camera.
Monitor
9,'(2,1
$8',2,1
$8',2287
Camera
16_ installation & connection
/223287
Ethernet Connection
Connect the Ethernet cable to the local network or to the Internet.
Power Supply
J
 Be careful not to reverse the polarity when you connect the power cable.
You can also use a router featuring PoE (Power over Ethernet) to supply power to the device.
 If PoE and DC 12V are both applied, this device will get supplied with power from PoE.
 If you want to connect an external device, you must turn off the external device before proceeding.
6'&$5'
(7+(51(73R(
6'
5(6(7
32:(5
''6*1&&012
566(16255(/$<287
'&9
Power
Ethernet
Electrical Resistance of Copper Wire at [20°C (68°F)]
Copper Wire Gauge (AWG)
#24(0.22mm2)
#22(0.33mm2)
#20(0.52mm2)
#18(0.83mm2)
0.018
Resistance (Ω/m)
0.078
0.050
0.030
Drop Voltage (V/m)
0.028
0.018
0.011
0.006
Recommended Distance (m)
Less than 20
Less than 30
Less than 30
Less than 30
 As shown in the table above, you may encounter a voltage-sag depending on the wire length.
If you use an excessively long wire for network video encoder connection, the network video encoder may
not work properly.
- Network Video Encoder Operating Voltage : DC 12V±10%
- Voltage drop measurements on the chart above may vary depending on the type and manufacture of
the copper cable.
English _17
● INSTALLATION & CONNECTION
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the network video encoder.
installation & connection
Connecting to Audio Input/Output
Speaker
Camera
Microphone
PC
Network
Microphone
Amp
Microphone
Speaker
Amp
1. Connect the AUDIO IN port of the network video encoder with the microphone
directly or LINE OUT port of the amplifier that the microphone is connected to.
2. Connect the AUDIO OUT port of the network video encoder with the speaker or
LINE IN port of the amplifier that the speaker is connected to.
3. Check the specifications for audio input.
18_ installation & connection
● INSTALLATION & CONNECTION
 Audio Codec
G.711 PCM. μ-law 64kbps 8kHz sampling
 Full duplex Audio
 Audio in
Used for mono signal line input (Max.2.4 Vpp)
 Audio out
Used for mono signal line output (Max.2.4 Vpp)
 Line out impedance
600
Alarm I/O Wiring Diagram
ALARM IN
3
(12mA sink)
GND
4
ALARM OUT
(NC)
5
ALARM COM
6
ALARM OUT
(NO)
7
J
(24VDC 1A,
125VAC 0.5A MAX)
 For controlling the power with electrical contacts, a separate circuit is required.
English _19
installation & connection
Connecting to the I/O port box
Connect the Alarm I/O signal to the corresponding port of the rear port box.
6'&$5'
(7+(51(73R(
''6*1&&012
6'
5(6(7
32:(5
566(16255(/$<287
'&9
Port
566(16255(/$<287
''6*1&&012
Description
Port
Description
D+
RS-485 Data Line
NC
Alarm Out (for Normal Close)
D-
RS-485 Data Line
CM
Alarm Out (Common)
S1
Alarm In
NO
Alarm Out (for Normal Open)
G
GND
Connecting to the RS-485 device
Connect the external device to the [RS-485 D+, D-] ports.
You can connect and control PTZ camera that supports RS-485 communication.
 Depending on camera’s type, connection polarity can be different.
For further information, refer to the corresponding PTZ Camera’s documentation.
Connecting to the Alarm Input
Connect one signal cable (out of 2) of applicable sensor to the [S1] port, and the other to
the [G] port.
Connecting the Alarm Output
Connect one signal cable (out of 2) of applicable external device to the [Alarm Out(NC, NO)],
and the other to the [CM] port.
20_ installation & connection
network connection and setup
You can set up the network settings according to your network configurations.
CONNECTING THE NETWORK VIDEO ENCODER DIRECTLY
TO LOCAL AREA NETWORKING
1. Launch an Internet browser on the local PC.
2. Enter the IP address of the network video encoder in the address bar of the browser.
IN
AUDIO
AUDIO OUT
IN
VIDEO
VIDEO IN
OUT
LOOP
LOOP OUT
Network Video Encoder
INTERNET
IN
AUDIO
AUDIO OUT
IN
VIDEO
VIDEO IN
OUT
LOOP
LOOP OUT
Network Video Encoder
Local PC
Firewall
External Remote PC
DDNS Server
(Data Center, KOREA)
<Local Network>
M
 A remote PC in an external Internet out of the LAN network may not be able to connect to the
network video encoder installed in the intranet if the port-forwarding is not properly set or a
firewall is set.
In this case, to resolve the problem, contact your network administrator.
 In the IP installer, you can use the initial password, “4321” to set IP Address ,Subnet Mask,
Gateway, HTTP Port, VNP Port, IP type. After changing the network interface, for better security,
access the web viewer and change the password.
 By factory default, the IP address will be assigned from the DHCP server automatically.
If there is no DHCP server available, the IP address will be set to 192.168.1.100.
To change the IP address, use the IP Installer.
For further details on IP Installer use, refer to “Static IP Setup”. (Page 26)
English _21
● NETWORK CONNECTION AND SETUP
Connecting to the network video encoder from a local PC in the LAN
network connection and setup
CONNECTING THE NETWORK VIDEO ENCODER DIRECTLY
TO A DHCP BASED DSL/CABLE MODEM
INTERNET
IN
AUDIO
AUDIO OUT
IN
VIDEO
VIDEO IN
OUT
LOOP
LOOP OUT
DSL/Cable Modem
Network Video Encoder
External Remote PC
DDNS Server
(Data Center, KOREA)
1. Connect the user PC directly with the network video encoder.
2. Run the IP Installer and change the IP address of the network video encoder so that
you can use the web browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the web viewer.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Network] – [Interface], and set the network type to [DHCP].
7. Connect the network video encoder, which was removed from your PC, directly to
the modem.
8. Restart the network video encoder.
M
 For registering the DDNS settings, refer to “Registering with DDNS”. (page 61)
 For configuring the DDNS settings, refer to “DDNS”. (page 60)
 For setting the network type, refer to “Interface”. (page 58)
22_ network connection and setup
CONNECTING THE NETWORK VIDEO ENCODER DIRECTLY
TO A PPPoE MODEM
AUDIO OUT
IN
VIDEO
VIDEO IN
OUT
LOOP
LOOP OUT
PPPoE Modem
Network Video Encoder
External Remote PC
DDNS Server
(Data Center, KOREA)
1. Connect the user PC directly with the network video encoder.
2. Run the IP Installer and change the IP address of the network video encoder so that
you can use the web browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the web viewer.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Network] – [Interface] Setup Page, set the network type to [PPPoE],
and enter the ID and password.
7. Connect the network video encoder, which was removed from your PC, directly to
the modem.
8. Restart the network video encoder.
M
 For registering the DDNS settings, refer to “Registering with DDNS”. (page 61)
 For configuring the DDNS settings, refer to “DDNS”. (page 60)
 For setting the network type, refer to “Interface”. (page 58)
English _23
● NETWORK CONNECTION AND SETUP
INTERNET
IN
AUDIO
network connection and setup
CONNECTING THE NETWORK VIDEO ENCODER TO A
BROADBAND ROUTER WITH THE PPPoE/CABLE MODEM
This is for a small network environment such as homes, SOHO and ordinary shops.
IN
AUDIO
AUDIO OUT
IN
VIDEO
VIDEO IN
OUT
LOOP
LOOP OUT
Network Video Encoder
INTERNET
IN
AUDIO
AUDIO OUT
IN
VIDEO
VIDEO IN
OUT
LOOP
LOOP OUT
Network Video Encoder
PPPoE or
Broadband router Cable Modem
Local PC
PPPoE or
Cable Modem
External Remote PC
DDNS Server
(Data Center, KOREA)
Configuring the network settings of the local PC connected to a
broadband router
Configuring the network settings of the local PC connected to a broadband router, follow
the instructions below.
 Select : <Network Neighborhood>  <Properties>  <Local Area Connection>
 <Properties>  <General>  <Internet Protocol (TCP/IP)>  <Properties> 
<Obtain an IP address automatically> or <Use the following IP address>.
 Follow the instructions below if you select <Use the following IP address>:
ex1) If the address (LAN IP) of the Broadband router is 192.168.1.1
IP address : 192.168.1.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
ex2) If the address (LAN IP) of the Broadband router is 192.168.0.1
IP address : 192.168.0.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.0.1
ex3) If the address (LAN IP) of the Broadband router is 192.168.xxx.1
IP address : 192.168.xxx.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.xxx.1
M
 For the address of the Broadband router, refer to the product’s documentation.
 For more information about port forwarding of the broadband router, refer to “Port Range Forward
(Port Mapping) Setup”. (Page 30)
24_ network connection and setup
BUTTONS USED IN IP INSTALLER
b c
● NETWORK CONNECTION AND SETUP
Item
m
Description
Device Name
Model name of the connected network device.
Click the column to sort the list by model name.
However, search will be stopped if clicked during the search.
b
Alias
This function is not currently implemented.
c
Mode
Displays either <Static>, <Dynamic> or <PPPoE> for the current network
connection status.
MAC(Ethernet)
Address
Ethernet address of the connected network device.
Click the column to sort the list by Ethernet address.
However, search will be stopped if clicked during the search.
IP Address
IP address.
Click the column to sort the list by IP address.
However, search will be stopped if clicked during the search.
Protocol
Network settings of the network device.
The factory default is “IPv4”.
Network device with the IPv6 setting will be displayed “IPv6”.
English _25
network connection and setup
Item
Description
URL
DDNS URL address enabling access from the external Internet.
However, this will be replaced with the <IP Address> of the encoder if
DDNS registration has failed.
IPv4
Scans for network device with the IPv4 setting.
IPv6
Scans for network device with the IPv6 setting.
Activated in an IPv6 compliant environment.
Search
Scans for network devices that are currently connected to the network.
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.
Auto Set
The IP Installer automatically configures the network settings.
Manual Set
You should configure the network settings manually.
Exit
Exits the IP Installer program.
m
M
 For the IP installer, use only the installer version provided in the installation CD or use the latest
one if available. You can download the latest version from the Samsung web site (www.
samsungcctv.com).
STATIC IP SETUP
Manual Network Setup
Run <IP Installer_v2.XX.exe> to display the network device search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
M
 For network devices found with the IPv6 setting, these buttons will be grayed out as the network
devices do not support this function.
1. Select a network device from the
search result.
Check the MAC address of the device
on the network device’s label.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
2. Click [Manual Set].
The Manual Setting dialog appears.
<IP Address>, <Subnet Mask>, <Gateway>, <HTTP Port>, and <VNP Port> of
the network devices are displayed in the preset values.
26_ network connection and setup
M
 IP related parameters can be set only
when DHCP is not checked.
If using a broadband router
 IP Address : Enter an address falling in
the IP range provided by the Broadband
router.
ex) 192.168.1.2~254,
192.168.0.2~254,
192.168.XXX.2~254
 Subnet Mask : The <Subnet Mask>
of the Broadband router will be the
<Subnet Mask> of the network video
encoder.
 Gateway : The <Local IP Address> of
the Broadband router will be the <Gateway> of the network video encoder.
M
 The settings may differ depending on the connected Broadband router model.
For more information, refer to the user manual of the applicable router.
 For more information about port forwarding of the broadband router, refer to “Port Range
Forward (Port Mapping) Setup”. (Page 30)
If not using a broadband router
For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator.
4. In the <Port> pane, provide necessary
information.
 HTTP Port : Used to access the
network device using the Internet
browser, defaulted to 80.
 VNP Port : Used to control the video
signal transfer, defaulted to 4520.
5. Enter the password.
Enter the password of “admin” account, which was used to access the network
device.
English _27
● NETWORK CONNECTION AND SETUP
3. In the <Address> pane, provide the
necessary information.
 MAC (Ethernet) Address : The MAC
address imprinted on the network
device label is automatically displayed
and requires no user setting.
network connection and setup
J
 For the security purposes, you are recommended to use a combination of numbers, alphabets
uppercase and lowercase and special characters for your password.
 If you want to change the password, refer to “Administrator password change” of the user
setup. (page 82)
6. Click [OK].
Manual network setup will be completed.
If the Broadband router has more than one network video encoder connected
Configure the IP related settings and the Port related settings distinctly with each other.
Category
IP related settings
Port related settings
M
Network video encoder #1 Network video encoder #2
IP Address
Subnet Mask
Gateway
192.168.1.100
255.255.255.0
192.168.1.1
192.168.1.101
255.255.255.0
192.168.1.1
HTTP Port
VNP Port
8080
4520
8081
4521
 If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar
of the Internet browser before you can access the network video encoder.
ex) http://IP address : HTTP Port
http://192.168.1.100:8080
Auto Network Setup
Run <IP Installer_v2.XX.exe> to display the network device search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
M
 For network devices found with the IPv6 setting, these buttons will be grayed out as the network
devices do not support this function.
1. Select a network device from the
search result.
Check the MAC address of the device
on the network device’s label.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
28_ network connection and setup
2. Click [Auto Set].
The Auto Setting dialog appears.
The <IP Address>, <Subnet Mask>, and <Gateway> will be set automatically.
J
● NETWORK CONNECTION AND SETUP
3. Enter the password.
Enter the password of “admin” account,
which was used to access the network
device.
 For the security purposes, you are
recommended to use a combination of
numbers, alphabets uppercase and
lowercase and special characters for your
password.
 If you want to change the password, refer
to “Administrator password change” of
the user setup. (page 82)
4. Click [OK].
Auto network setup will be completed.
DYNAMIC IP SETUP
Dynamic IP Environment Setup
 Example of the Dynamic IP environment
- If a Broadband Router, with a network device connected, is assigned an IP
address by the DHCP server
- Network device is connected to a DHCP based modem directly
- If IPs are assigned by the internal DHCP server via the LAN
Checking the Dynamic IP
1. Run the IP Installer on the user’s local
computer.
Network devices allocated with
<Dynamic IP> address are shown in
the list.
2. Select a network device from the
search result.
English _29
network connection and setup
3. Click the [Manual Set] button and
check the network device’s <Dynamic
IP> address.
If you uncheck <DHCP>, you can
change IP to <Static>.
PORT RANGE FORWARD (PORT MAPPING) SETUP
If you have installed a broadband router with a network video encoder connected, you must set
the port range forwarding on the Broadband router so that a remote PC can access the network
video encoder in it.
Manual Port Range Forwarding
1. From the Setup menu of the Broadband
router, select <Applications &
Gaming> - <Port Range Forward>.
For setting the port range forward for
a third-party Broadband router, refer
to the user guide of that Broadband
router.
2. Select <TCP> and <UDP Port> for
each connected network video encoder
to the Broadband router.
Each port number for the Broadband
Router should match that specified in
<Setup> - <Network> - <Port> from
the encoder’s web viewer menu.
3. When done, click [Save Settings].
Your settings will be saved.
M
 Above sample instructions are based on the CISCO’s Broadband router.
 The settings may differ depending on the connected Broadband router model.
For more information, refer to the user manual of the applicable router.
30_ network connection and setup
Setting up Port Range Forward for several network video encoders
When several network video encoder connect to one Broadband router device, you should
forward the TCP 943 port of the router to the TCP 943 port of a connected network video
encoder.
 If you don't set properly the TCP 943 port of the router, you cannot get any video stream from the
web page of the network video encoder.
 TCP 943 port is a port for the Silverlight policy server of a network video encoder.
 You can set a rule of Port Forwarding on the Broadband router device through its
configuration web page.
 You cannot change the Silverlight policy server port of a network video encoder.
 You can change the ports of the network video encoder except the policy server port
through its configuration web pages.
When Network video encoder1 and Network video encoder2 are connected to a router :
User

Internet

Start
943
3000
3001
4520
4521
8080
8081
M
Broadband Router
End
Protocol
943
TCP
3000
TCP/UDP
3001
TCP/UDP
4520
TCP/UDP
4521
TCP/UDP
8080
TCP/UDP
8081
TCP/UDP
IP Address
192.168.1.100
192.168.1.100
192.168.1.101
192.168.1.100
192.168.1.101
192.168.1.100
192.168.1.101


Network video encoder1
(192.168.1.100)
HTTP Port
8080
Device port
4520
RTSP port
3000
Policy server port
943
Network video encoder2
(192.168.1.101)
HTTP Port
8081
Device port
4521
RTSP port
3001
Policy server port
943
 Port forwarding can be done without additional router setup if the router supports the UPnP
(Universal Plug and Play) function.
After connecting the encoder, set <Quick connect> of <Samsung DDNS> to <On> in the
“Setup  Network  DDNS” menu.
English _31
● NETWORK CONNECTION AND SETUP
J
network connection and setup
CONNECTING TO THE NETWORK DEVICE FROM A
SHARED LOCAL PC
1. Run the IP Installer.
Searches for connected network devices
and displays on the list.
2. Double click the desired network device
to connect to.
The Internet browser starts and
connects to the network device.
M
 You can also access the vieo encoder in such way you type the IP address of the found network
device in the address bar of the Internet browser.
CONNECTING TO THE NETWORK VIDEO ENCODER FROM
A REMOTE PC VIA THE INTERNET
Since using the IP Installer on a remote computer that is not in the Broadband router’s network
cluster is not allowed, users can access network video encoders within a broadband router’s
network by using the network video encoder’s DDNS URL.
1. Before you can access a network video encoder in the Broadband router network,
you should have set the port range forward for the Broadband router.
2. From the remote PC, launch the Internet browser and type the DDNS URL address
of the network video encoder, or the IP address of the Broadband router in the
address bar.
ex) http://www.samsungipolis.com/Product ID
M
 For registering the DDNS settings, refer to “Registering with DDNS”. (page 61)
32_ network connection and setup
web viewer
CONNECTING TO THE NETWORK VIDEO ENCODER
Normally, you would
1. Launch the Internet browser.
● WEB VIEWER
2. Type the IP address of the network
video encoder in the address bar.
ex) • IP address (IPv4) : 192.168.1.100
 http://192.168.1.100
- the Login dialog should appear.
• IP address (IPv6) : 2001:230:abcd:
ffff:0000:0000:ffff:1111
 http://[2001:230:abcd:ffff::ffff:1111]
- the Login dialog should appear.
If the HTTP port is other than 80
1. Launch the Internet browser.
2. Type the IP address and HTTP port number of the network video encoder in the
address bar.
ex) IP address : 192.168.1.100:HTTP Port number(8080)
 http://192.168.1.100:8080 - the Login dialog should appear.
Using URL
1. Launch the Internet browser.
2. Type the DDNS URL of the network video encoder in the address bar.
ex) URL address : http://www.samsungipolis.com/Product ID
- the Login dialog should appear.
J
 Network connection is disabled in the LAN only environment.
English _33
web viewer
To check the DDNS address
If the network video encoder is connected directly to the DHCP cable modem, DSL
modem, or PPPoE modem, the IP address of your network will be changed each time you
try to connect to the ISP (Internet Service Provider) server.
If this is the case, you will not be informed of the IP address changed by DDNS.
Once you register a dynamic IP-based device with the DDNS server, you can easily check
the changed IP when you try to access the device.
To register your device to the <DDNS> server, visit www.samsungipolis.com and register
your device first, and then set the Web Viewer’s <Network> - <DDNS> to <Samsung
DDNS>, as well as providing <Product ID> that had been used for DDNS registration.
34_ web viewer
PASSWORD SETTING
J
● WEB VIEWER
When you access the product for the first time,
you must register the login password.
When the “Password change” window appears,
enter the new password.
 A new password should be eight to fifteen
letters long and a combination of at least
two of uppercase/lowercase alphabets, numbers and special characters.
- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/
 You cannot use your ID as your password. You cannot repeat same letters more than twice and
you cannot use the three consecutive keyboard buttons.
 If you lost your password, you can press the [RESET] button to initialize the product. So, don’t lose
your password by using a memo pad or memorizing it.
LOGIN
Whenever you access the product, the login window appears.
Enter the User ID and password to access the product.
1. Enter “admin” in the <User name>
input box.
The administrator ID, “admin”, is fixed
and can not be changed.
2. Enter the password in the <Password>
input field.
3. Click [OK].
If you have logged in successfully, you
will the Live Viewer screen.
M
 If you check the “Remember my credentials” option when your input is done, in future you will
be logged in automatically without being prompted to enter the login information.
 You will experience the best video quality if the screen size is 100%. Reducing the ratio may cut
the image on the borders.
English _35
web viewer
INSTALLING SILVERLIGHT RUNTIME
If your PC has not installed Silverlight Runtime or has just installed an old runtime version, you will
be redirected to the Silverlight Runtime installation page automatically when accessing the web
viewer.
To install on Windows OS
1. Click <Click Here>.
2. When the file download dialog pops up,
click <Run>.
3. When the download is completed, click
<Run>.
4. The Silverlight Runtime installation page
will be displayed. <Install now> to
proceed with the installation.
36_ web viewer
5. When done, click <Close>.
● WEB VIEWER
To install on MAC OS
1. Run the file trailing with “.dmg”.
2. Run the install package file automatically created, ending
with “.pkg”.
3. Click <Continue>.
English _37
web viewer
4. Select your language on the language
selection screen, and click <Continue>.
5. Click <Agree>.
6. Click <Install>.
38_ web viewer
7. Enter the password of the account
currently logged in, and click <Install
Software> and continue.
● WEB VIEWER
8. Once completed, click <Close>.
English _39
web viewer
INSTALLING STW WebViewer PLUGIN
If connecting to an encoder for the first time, you will see the installation message. Then, install
the required WebViewer Plugin to access the encoder and control the video from it in real time.
1. When the monitoring page is accessed
for the very first time, the installation
page is displayed. Click [Click Here] to
begin installation.
J
 If the plug-in installation file download status is suspended at 99% in the Internet Explorer
browser, retry it after selecting “Release SmartScreen filter” in “Tool  SmartScreen filter”.
2. Click [Run] in the message window.
3. Click [Yes] when the notice window
saying that all browser windows will be
closed.
4. When the old version of the Web Viewer
Plug-in is installed, a notice window
saying the old version will be deleted is
displayed.
Click [Yes] when the notice window is
displayed.
M
 Steps 4 and 5 will be skipped if no Web Viewer Plug-in is installed.
40_ web viewer
5. Click [OK].
The old version of Web Viewer Plug-in
is deleted.
● WEB VIEWER
6. Click [Install] to begin installation of the
Web Viewer Plug-in.
7. Click [Finish].
STW Web Viewer Plug-in installation is
completed.
English _41
web viewer
USING THE LIVE SCREEN
b
c
m
Item
b
c
Description
Monitoring
Move to the monitoring screen.
Playback
Switch to the monitoring screen that plays recording data in the SD memory.
Setup
Move to the Setup screen.
Displays the Live video on the screen.
Viewer Screen
 You can use the mouse wheel to activate the digital zooming in Viewer screen.
You can select a profile type in <Video profile> under the <Video & Audio> setup
menu.
Profile type
Screen
Optimization
The video size of the camera will switch to as big as the Web browser.
Fix the resolution
Regardless of the resolution setup configured in the camera, it sets the resolution to
640x480. Press it again to switch back to the default resolution.
 When the Web Viewer is connected, the profile information currently using is
displayed.
42_ web viewer
Item
Full Screen
Switch the current video to the maximum size of the monitor.
Capture
Saves the snapshot as an image file in the .bmp or .jpg format.
Audio/Microphone Enable Audio and Microphone are control the Audio volume.
Control
 Only the Audio volume can be controlled.
Alarm output
● WEB VIEWER
Description
Activate the Alarm Out port.
Connect the external PTZ to the RS-485 terminal and control the PTZ camera lens
direction with the arrow keys.
External PTZ
 The pan/tilt operations will be enabled only if the camera is connected to a pan/
tilt-compliant receiver.
m
Hide the context
menu
The left-corner context menu will disappear but only the menu icon.
To capture the snapshot
1. Click [Capture (
)] on the scene to
capture.
The Capture dialog should appear.
2. Confirm the save path and click [Save]
button.
The screenshot will be saved in the
specified path.
M
 If you encounter an interrupted video
when capturing the image with IE8 on a
Windows 7-based PC, deselect “Turn On
Protected Mode” from “Tools – Internet Options – Security”.
 If the screen is not captured by IE browser in Windows 7 or 8, run the IE Browser with the Admin
privilege.
English _43
web viewer
To fit the full screen
1. Click the [Full Screen (
)] button.
2. This will fit the Viewer to the full screen.
3. To exit the full screen mode, press [Esc] on the keyboard.
M
 For the Internet Explorer and Google Chrome browser, you can switch to the full screen.
To Use Audio
1. Click [Audio (
M
)] icon to activate audio communication.
] bar to control the volume.
2. Use [
 If there is no sound from pulling in and out the audio jack while it is in operation, click the
[Audio (
)] icon to enable it again.
To Use Microphone
Click [Mic (
)] icon to activate the microphone.
To control the PTZ
1. Click the [PTZ (
)] tab.
2. When the PTZ icon appears on the
screen, use the direction buttons to
adjust the camera angle, zoom factor
or focus to your preference.
M
 For further details on PTZ use, refer to
“External PTZ setup”. (page 55)
44_ web viewer
PLAYING THE RECORDED VIDEO
M
 Before you can play the video, you must configure the record settings. For details on record settings,
refer to “Storage”. (page 69)
● WEB VIEWER
Name of event search screen and its function
b
c
Item
Description
Search range setting Set the search date and time from the data saved in the SD memory card.
b
Search event setting Set the event type to search within the search period.
c
Event search
Run the event search.
English _45
web viewer
To play the content after searching by event
1. Click the [Playback (
)] tab.
2. Specify the start time and end time of
your search.
3. Select an event type for your search
within the specified period.
4. Click the [Event search] button.
The search results will be displayed in
the list.
M
 If more than 800 events are recorded
within the search period, your search will
be limited up to the date when the 800th event is recorded.
For instance, if the search period is between 10th and 15th day of the month, and more than 800
events were recorded 10th through 11th, your search will be limited up to 11th day with a total of
800 events, and events after then (from 12th) will not be found.
5. Select a data item to play in the search
list.
6. Click the [Play (
)] button.
7. To stop playing the video, click
[Stop (
)].
8. To return to the search screen, click
)].
[Exit (
46_ web viewer
Name of time search screen and its function
● WEB VIEWER
b
c
Item
Description
Time bar
The section in the specific period is played by moving the time bar.
b
Search date setting
 Dates for which there is video in the SD memory card are displayed
Set the search date using the calendar.
within the boxes on the calendar.
c
Screen optimization
The camera image is converted to fit the Web browser window.
Fix the resolution
Regardless of the resolution setup configured in the camera, it sets
the resolution to 800x600. Press it again to switch back to the default
resolution.
Full screen
The current image is converted to cover the maximum size of the monitor.
Capture
The current image is saved as a .jpg or .bmp image file.
English _47
web viewer
Item
Video information
Backup
Description
Time data of the replayed video is displayed on the screen.
Time zone is set to back up the video saved in the SD memory card.
 Can be set as up to 5 minutes.
To play after searching by time
1. Click the [Time Search (
)] tab.
2. Click a desired date in the calendar.
The video on the specified date will be
played.
3. If the video playback is stopped, select
)].
a time and click [Play (
The video on the selected time will be
played.
4. While the video is being played, the
recording time for the current video will
be shown.
5. Search for the video forward or backward, and control the play speed.
- To control the play speed
If selecting ), the button will switch to x1, x2, x4, x8, and the play speed will
increase accordingly.
When the ( button is selected, the playing speed is decreased to -1x, -2x, -4x, -8x
and the playing speed slows down gradually. Subsequently the quick playing speed
is returned to the normal speed and the reverse playing speed increases.
- To control the playback direction
If you see the ) button with the play speed displayed, the video will be played
forward; Whereas, if you see the ( button with the play speed displayed, the video
will be played backward.
)] to a desired time point of the video before playing it.
6. Move [Time bar (
The time containing a normal recoding file will be highlighted in blue; the time with
the event recording will be highlighted in red.
48_ web viewer
To back up the searched video
● WEB VIEWER
1. During playback, click [
] on the
scene to back up.
The scheduling window for backup
start and end time appears.
2. Click [
] button.
The Save As window appears.
3. Confirm the save path and click [Save]
button.
The screenshot will be backed up to
the specified path.
To play the backup video
The backed up images are saved in an .avi format. Gom Player, VLC Player, and Window
Media Player are recommended as the media player compatible with this format.
M
 In case of Windows Media Player, download the latest codec from www.windows7codecs.com
and install it prior to use.
English _49
web viewer
To Play an AVI File
J
 The AVI file does not contain the recording time data.
1. Separate the SD memory card from the encoder.
J
 Before separating the SD memory card, set the <Device> to <Off> in the “Setup  Event 
Storage” menu.
2. Insert the SD memory card into the PC.
3. Play the AVI file in the “\ch00\img\
YYYY_MM_DD” directory, using a
media player.
M
 The file name begins with “01.avi” and
the file number increments by 1.
 Once corrupted, the data in the SD
memory card cannot be replayed in Web
Viewer Playback.
50_ web viewer
setup screen
SETUP
You can configure the video & audio, network, event and system settings of the encoder in the
network.
)].
2. The Setup screen appears.
J
 Microsoft Silverlight 5.0 or higher is required to be installed on the PC for setup pages that
provide preview video.
If not installed already, automatically moves to the Silverlight setup.
VIDEO & AUDIO SETUP
Video profile
1. From the Setup menu, select the
<Video & Audio (
)> tab.
2. Click <Video profile>.
3. Set the <Video profile connection
policy>.
 Keep connection when profile
setting is changed : Changing profile
properties that is used by existing
connection does not affect such
connection and remains with old
profile setup.
If not selected, changing a profile
used by an existing connection
resets such connection.
4. Select each profile properties.
For more details, refer to “To Add/
Change the Video Profile”. (Page 53)
5. Click the input box of each item and
enter / select a desired value.
 The context menu may differ depending on
the selected codec type.
 Default profile : If no profile is
selected when using the Web Viewer,
the default video profile is applied.
English _51
● SETUP SCREEN
1. In the Live screen, click [Setup (
setup screen
 E-mail/FTP profile : Video profile to be transferred to the specified email or FTP
site.
 Only the MJPEG codec can be set as the E-mail/FTP profile.
 Record profile : This is the profile that is applied to video recording.
 Audio-In : Sets whether to use audio for video recordings.
6. According to your situation, set ATC (Auto Transmit Control) mode.
 ATC mode : It adjusts the video
properties according to the variance
in the network bandwidth, controlling
the bit rate. Adjusting the bit rate
depends on the ATC mode.
- Control framerate : Reduce the frame rate if the network bandwidth drops down.
- Control compression : Control the compression rate if the network bandwidth
drops down.
Compression adjustment can cause deterioration of the image quality.
 If <Bitrate control> is set to <CBR>, the encoding priority according to the ATC mode will be
fixed as below:
Bitrate control / ATC mode
Control framerate
Control compression
CBR
Framerate
Compression
 ATC sensitivity : Affect the transfer rate according to the variance in the network
bandwidth.
The transfer rate will be adjusted to the fastest if the bandwidth is <Very high>,
and adjusted to the latest if the bandwidth is <Very low>.
 ATC limit : If the quality or frame rate is adjusted, the property will be changed to
the applied value (%) against the previous setting value (100%).
Note that if you reduce the property value too much, you may encounter flickering
on the screen. So it is advisable to adjust the value within the threshold.
J
 It is recommended to apply ATC control only for encoders supporting ATC.
 Set the ATC sensitivity to <Very low> in a network environment with high variance in the network
bandwidth.
 If the network connection is unstable, you may encounter flickering on the screen.
7. When done, click [Apply (
52_ setup screen
)].
To Add/Change the Video Profile
The profile setup can be added or modified to accommodate various profiles depending on
the recording conditions.
3. Specify the conditions under which the codec will be applied.
4. Specify the details of the selected codec including resolution and frame rate.
Click <Advanced> to display the context menu.
 Resolution : Set the video size of the MPEG-4, H.264, and MJPEG files.
 Framerate : Specify the frame rate.
 Compression : Specify the compression rate of the video.
 Maximum bitrate : Specify the maximum bit rate of the video.
J
 As the bit rate can be adjusted limitedly according to the resolution, frame rate and screen
complexity, the actual bit rate can be greater than the maximum bit rate. So you must
consider the use conditions when setting the value.
 Bitrate control : You can select one from constant bit rate and variable bit rate for
compression. Constant bit rate (CBR) varies the video quality and fixes network
transfer bit rate, while variable bit rate emphasizes the quality by varying network
transfer bit rate.
J
 If the bit-rate control is set to the Constant Bit Rate, the actual transmission frame rate may
be less than the set frame rate because the Frame Rate First Mode is changed to the
Compression Rate First Mode to ensure the highest image quality at a bit rate which is set
depending on the complexity of the screen.
 Target bitrate : Specify the bit rate at which you will transfer the video.
 Encoding priority : You can set the video transfer method to Framerate or
Compression.
 GOV length : It specifies the distance (in terms of number of frames) between two
consecutive I-Frames in a video sequence when H.264 codec was selected. (One
I-Frame + 0~Several P-Frames)
 Profile : You can select the H.264 profiling method.
 Entropy coding : Reduce the possible compression loss due to encoding.
 Multicast(SVNP) : Specify the use of the SVNP protocol.
- IP address : Enter an IPv4 address with which you can connect to the IPv4 network.
- Port : Specify the video communication port.
- TTL : Set the TTL for the SVNP packet.
English _53
● SETUP SCREEN
1. Select one from the <Video profile> options.
2. Provide the name and select a codec.
setup screen
 Multicast(RTP) : Specify the use of the RTP protocol.
- IP address : Enter an IPv4 address with which you can connect to the IPv4
network.
- Port : Specify the video communication port.
- TTL : You can set the TTL for the RTP packet.
J
 If you set the Multicast address to 224.0.0.0~224.0.0.255, multicast may not work properly
in all environments. In that case, we recommend you change the multicast address.
What is GOV length?
GOV(Group of Video object planes) is a set of video frames for MPEG-4 and H.264
compression, indicating a collection of frames from the initial I-Frame (key frame) to the next
I-Frame.
GOV consists of 2 kinds of frames: I-Frame and P-Frame.
I-Frame is the basic frame for the compression, also known as Key Frame, which contains
one complete image data. P-Frame contains only the data that has changed from the
preceding I-Frame.
For MPEG-4 and H.264 codec, you can determine the GOV length.
Audio setup
You can configure the I/O settings of the audio source from the encoder.
1. From the Setup menu, select the
)> tab.
<Video & Audio (
2. Click <Audio setup>.
3. Set the audio input value.
 Gain : Specify the audio input
amplification.
J
 Sound quality deterioration or howling may occur if the loudness of the sound source or gain
value were set excessively.
4. Set the audio output level.
 Enable : Sets whether to use audio output.
 Gain : Specify the audio output amplification.
5. When done, click [Apply (
54_ setup screen
)].
External PTZ setup
Set the connection value for an external PTZ camera to control the PTZ by using the
RS-485 connection of the camera.
)> tab
● SETUP SCREEN
1. Select the <Video & Audio (
from Setup menu.
2. Click <External PTZ setup>.
3. Specify the serial port.
Once a camera is connected, you can
set the RS-485 communication mode.
 Protocol : Select the same protocol
as your camera from SAMSUNG-T
/ SAMSUNG-E / PELCO-D /
PELCO-P / SUNGJIN / PANASONIC
/ HONEYWELL / AD / VICON / GE /
BOSCH.
 Camera ID : Displays the fixed
camera ID.
 Baudrate : Transfer rate for RS-485 communications.
 Data bit : Specify the data bit.
 Parity bit : Specify the parity bit.
 Stop bit : Specify the stop bit.
4. When done, click [Apply (
M
)].
 To do this, you have to make sure the camera and the device are connected properly via RS-485
communication ports. In addition, the serial port for the connected camera should be able to
function properly.
5. Set the menu for the connected camera.
For more details, refer to the section of “To set the camera menu”. (page 57)
6. Click the <PTZ> button in the upper right corner and move to the PTZ setting menu.
English _55
setup screen
7. Adjust the direction.
 [Change direction to (
)/(
)/(
)/(
)/(
)/(
)/(
)/(
)] : The
camera direction is adjusted.
 [Moving speed control (
)] : The bigger the number is, the faster the moving
speed becomes.
8. Set the zoom and focus.
 [Zoom In (
)] : Zooms in the screen.
 [Zoom Out (
)] : Zooms out the screen.
 [Adjust Focus (
/
)] : Adjusts the
focus in the screen.
 [Zoom Speed Control (
)] : The bigger
the number is, the faster the zoom speed becomes.
9. Set the preset.
M
 Only when the camera and device’s RS-485 communication ports are connected and the
<Serial setup> is normal, you can control Pan/ Tilt/ Zoom.
To add a preset
1. Select the preset number to add.
2. Set the name for the preset.
3. Press the [
] button.
To delete a preset
1. Select the preset number to delete.
2. Press the [
] button.
To move a preset
1. Select a preset number that you want to move.
2. Press the [
56_ setup screen
] button.
To set the camera menu
Run the web viewer to retrieve the camera setting menu and change the setting.
● SETUP SCREEN
1. Click on the <OSD> button in the upper
right corner and move to the OSD
setting menu.
2. Click the [
/
] button to move to
the desirable menu.
] button or [
]
3. Click the [
button to move to the menu or cancel.
M
 The camera menu may differ depending
on the type of camera connected.
English _57
setup screen
NETWORK SETUP
Interface
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <Interface>.
3. Set the <Interface> and <IPv6 setup>
as necessary.
 IP type : Select an IP connection type.
- Manual : Specify the IP address,
Subnet mask, Gateway, DNS1,
and DNS2.
- DHCP : Specify the DNS1 and
DNS2.
- PPPoE : Specify the DNS1, DNS2, ID and Password.
 If you set it to <Manual>, you should specify the IP, Subnet mask, Gateway, DNS 1 & 2 manually.





MAC address : Shows the MAC address.
IP address : Displays the current IP address.
Subnet mask : Displays the <Subnet mask> for the set IP.
Gateway : Displays the <Gateway> for the set IP.
DNS1/DNS2 : Displays the DNS(Domain Name Service) server address.
4. Set the <IPv6 setup>.
 Set to <Use> to use IPv6 address.
 Default : Use the default IPv6 address.
 DHCP : Display and use the IPv6 address obtained from the DHCP server.
 Manual : Enter IP address and gateway manually and use it.
5. When done, click [Apply (
J
)].
 The IP addressing system will be defaulted to DHCP. If no DHCP server is found, the previous
settings will be restored automatically.
 Once completed with editing, click [Apply (
After a while, connect again with the changed IP.
58_ setup screen
)] to apply changes and the browser exits.
Port
1. From the Setup menu, select the
<Network (
)> tab.
3. Type in each item in the Port menu as
necessary.
 Neither the port range between 0 and 1023
nor port 3702 is available.
 HTTP port : HTTP port used to
access the encoder via the web browser.
The default is 80(TCP).
 Setting the HTTP port for Safari and Google Chrome browsers to 65535 is not allowed by security
policy.
 Device port : Set a port used to transfer video signals with the Samsung
protocols.
 RTSP port : Used to transfer videos in the RTSP mode; the default is 554.
 Web streaming port : Used to transfer videos to the Web Viewer; the default is 4520.
 Silverlight policy port : Silverlight is used to permit to acquire a network
connection; the default is 943.
M
 If changed the HTTP port, the browser exits.
Afterwards, address should contain the newly assigned HTTP port trailing the IP.
ex) IP address: 192.168.1.100, HTTP port : Assigned 8080  http://192.168.1.100:8080
(If HTTP port is set to 80, no need to specify the port number)
 The port range of the Web Streaming is between 4502 and 4534. If the Device port is with this
effective range, the Web Streaming port should be specified the same as the Device port.
 You cannot change the Web Streaming/Silverlight policy server port of an encoder.
4. When done, click [Apply (
)].
English _59
● SETUP SCREEN
2. Click <Port>.
setup screen
DDNS
DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of
an encoder into a general Host Name so that the user can easily remember it.
1. From the Setup menu, select the
)> tab.
<Network (
2. Click <DDNS>.
3. Select the <DDNS> connection type.
4. Type in the DDNS items according to
the selected type.
 Samsung DDNS : Select this if you
use the DDNS server provided by
Samsung Techwin.
- Product ID : Enter the product ID that is registered with the Samsung DDNS
service.
- Quick connect : It sets port forwarding automatically when used with a UPnP
(Universal Plug and Play) supporting router.
 Public DDNS : Select one of provided public DDNS servers when you use a public
DDNS server.
- Service : Select desired public DDNS service server.
- Host name : Enter the name of the host that is registered with the DDNS server.
- User name : Enter the user name for the DDNS service.
- Password : Enter the password for the DDNS service.
5. When done, click [Apply (
J
)].
 If selected <Quick connect>, be sure to select Samsung DDNS service.
60_ setup screen
Registering with DDNS
To register your product with the Samsung DDNS
● SETUP SCREEN
1. Visit the iPOLiS web site
(www.samsungipolis.com) and sign in
with a registered account.
2. From the top menu bar, select <DDNS
SERVICE> - <MY DDNS>.
3. Click [PRODUCT REGISTRATION].
4. Enter the product ID.
 You must perform the duplicate check for the
ID that you entered.
5. Select a <CLASSIFICATION> and
specify the <MODEL NUMBER>.
6. Specify the product location with a
description if necessary.
7. Click [REGISTRATION].
The product will be added to the
product list that you can check.
English _61
setup screen
To connect to the Samsung DDNS in encoder setup
1. From the DDNS setup page, set
<DDNS> to <Samsung DDNS>.
2. Provide the <Product ID> that you
registered product ID with the DDNS
site.
3. Click [Apply (
)].
When the connection is successfully
made, you will see the message of
<(Success)> on the screen.
Configuring public DDNS in encoder Settings
1. Open the DDNS settings page and select <Public DDNS> for <DDNS>.
2. Enter the corresponding site’s host name, user name and password.
)] button.
3. Click [Apply (
If the connection properly establishes, <(Success)> appears.
4. When done, click [Apply (
M
)].
 To use DDNS service properly, both DDNS setup and the router’s port forwarding setup are
required.
For port forwarding setup, refer to “Port Range Forward (Port Mapping) Setup”. (page 30)
62_ setup screen
IP filtering
You can create a list of IPs that you want to grant or deny access to them.
● SETUP SCREEN
1. From the Setup menu, select the
)> tab.
<Network (
2. Click <IP filtering>.
3. Select <Filtering type>.
 Deny : If selecting this, access from
those IPs that are added to the
filtering will be restricted.
 Allow : If selecting this, access from
only those IPs that are added to the filtering will be accepted.
)] button.
4. Click the [Add (
The IP list will be created.
5. Provide the IP that you want to grant or deny access from.
When you enter an IP address and a Prefix, the list of IP addresses available will
appear in the right-side filter range column.
M
 If selected <Allow> for IP Filtering and <IPv6 setup> of <Interface> is set to <Use>, both
IPv4 and IPv6 addresses of the computer currently configuring should be assigned.
 The IP address of the computer used for the current setup cannot be added to <Deny>, it should
be added to <Allow>.
 Only the IP addresses that are set to <Use> will be displayed in the filter column.
6. Select an IP to delete from the list.
Click the [Delete (
)] button.
7. When done, click [Apply (
)].
English _63
setup screen
SSL
You can select a secure connection system or install the public certificate for this purpose.
1. From the Setup menu, select the
)> tab.
<Network (
2. Click <SSL>.
3. Select a secure connection system.
 To access the encoder using HTTPS mode, you
have to type the IP address for the encoder in
the form of “https://<Encoder_IP>”.
If you failed to configure the Web viewer
settings in HTTPS mode with Internet Explorer, edit the Internet options as follows: <Menu  Tools 
Internet Options  Advanced  Security  Uncheck TLS 1.0, and check TLS 1.1, TLS 1.2>
4. Search for the public certificate that you want to install on the encoder.
To install the certificate on the encoder, you need to provide a certificate name (it
can be arbitrarily assigned by the user), certificate file issued from the certification
authority and a key file.
 The <HTTPS (Secure connection mode using the public certificate)> item will be active only if
there exists a public certificate installed.
5. When done, click [Apply (
)].
Installing the certificate
1. Enter the certificate name.
2. Select the certificate file to be installed and certificate key, and click [Install (
button.
Deleting the certificate
1. Click [Delete (
)] button.
2. To delete a public certificate, you should access the network video decoder in
the mode of <HTTP (Do not use secure connection)> or <HTTPS (Secure
connection mode using a unique certificate)>.
64_ setup screen
)]
802.1x
When connecting network, you can choose whether using 802.1x protocol, and then install
the certification.
2. Click <802.1x>.
3. Set the <IEEE 802.1x setting(EAPOL
using EAP-TLS)>.
 Enable IEEE 802.1x : Specify the use
of the 802.1x protocol.
 EAPOL version : Select version 1 or 2.
 ID : Enter the client certificate ID.
 Password : Enter the client private key password. If the key file used is not
encrypted, you don’t need to enter it.
J
 If the connected network device does not support the 802.1x protocol, the protocol will not
operate properly even if you set it.
4. Install/remove the certificate.
 CA certificates : Select a public certificate that contains the public key.
 Client certificate : Select a public certificate that contains the client certificate key.
 Client private key : Select a public certificate that contains the client private key.
5. When done, click [Apply (
)].
To install/remove 802.1x related certificates
1. Press the [Browse (
)] button for each item and select a certificate to install.
2. If no certificate is installed, you will see “Not Available” appearing next to the selected
item.
3. Press the [Install (
next to the item.
)] button to start installation with a message of “Installed”
4. Press the [Delete (
)] button to remove the certificate.
English _65
● SETUP SCREEN
1. From the Setup menu, select the
)> tab.
<Network (
setup screen
QoS
You can specify the priority to secure a stable transfer rate for a specific IP.
1. From the Setup menu, select the
)> tab.
<Network (
2. Click <QoS>.
)] button.
3. Click the [Add (
The IP list will be created.
4. Enter an IP address to which you will
apply QoS.
M
 The default prefix for IPv4 is 32; For DSCP, the default is set to 63.
 Only the IP addresses that are set to <Use> can be prioritized.
5. Select an IP to delete from the list.
Click the [Delete (
)] button.
6. When done, click [Apply (
)].
SNMP
With the SNMP protocols, the system or network admin can monitor the network devices
on a remote site, and configure the environment settings.
1. From the Setup menu, select the
)> tab.
<Network (
2. Click <SNMP>.
3. Specify the <SNMP>.
 Enable SNMP v1 : SNMP version 1
will be active.
 Enable SNMP v2c : SNMP version 2
will be active.
- Read community : Provide the name of the read community where you can access
to the SNMP information. The default name is <public>.
- Write community : Provide the name of the write community where you can
access to the SNMP information. The default name is <write>.
66_ setup screen
 Enable SNMP v3 : SNMP version 3 will be active.
- Password : Specify the default password for SNMP version 3. The default
password is <admin4321>.
 The default password can be exposed to a hacking thread so it is recommended to change the
 Password should be longer than 8 characters, no more than 16 characters.
4. When done, click [Apply (
J
)].
 SNMP v3 is only able to be set when the secure connection mode is HTTPS.
Refer to “SSL”. (page 64)
English _67
● SETUP SCREEN
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
setup screen
EVENT SETUP
FTP / E-mail
You can configure the FTP/E-mail server settings so that you can transfer the images taken
with camera to your PC if an event occurs.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <FTP / E-mail>.
3. Select <FTP configuration> or
<E-mail configuration> and enter /
select a desired value.
 FTP configuration
- Server address : Enter the IP
address of the FTP server that you
transfer the alarm or event images
to.
- ID : Enter the user ID with which
you will log in to the FTP server.
- Password : Enter the user account
password for logging into the FTP server.
- Upload directory : Specify the FTP path where you will transfer the alarm or
event images.
- Port : The default port of the FTP server is 21; however, you can use a different
port number according to the FTP server settings.
- Passive mode : Select <On> if you need to connect in passive mode due to the
firewall or the FTP server settings.
68_ setup screen
4. When done, click [Apply (
)].
Storage
You can set the record conditions or the use of recording for the SD memory, check the
size of stored data, or format the SD memory itself.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <Storage>.
English _69
● SETUP SCREEN
 E-mail configuration
- Server address : Enter the IP address of the email server that you transfer the
alarm or event images to.
- Use authentication : Select whether to use authorization.
- Use SSL : Specify the use of SSL.
- ID : Enter the user ID for logging into the email server.
- Password : Enter the user account password for logging into the email server.
- Port : The default port of the email server is 25; however, you can use a different
port number according to the email server settings.
- Recipient : Enter the address of the email recipient.
- Sender : Enter the address of the email sender. If the sender address is
incorrect, the email from the sender may be classified as SPAM by the email
server and thus may not be sent.
- Subject : Enter a subject for your email.
- Body : Provide the text for the massage. Attach the alarm or event images to
the email that you are preparing.
setup screen
To make recording on the SD memory
1. Check the memory card’s <Free> size and <Total> size.
2. If there are sufficient free space, set the device to <On>.
Otherwise, check the stored data and if you find them not important, then click
<Format> to format the SD memory.
 Some frames may be skipped if the SD memory card operates at the lower speed than recommended.
For more details, refer to “Recommended SD/SDHC Memory Card Specifications”. (Page 10)
 For a SD memory card with a large capacity, the formatting will be slowed down accordingly.
 The data traffic will increase when the encoder is set to higher resolution, higher bit rate, and/or higher
framerate.
If there is too much data traffic, some frame may be skipped although it is stored in a full frame.
3. Specify the storage action.
 Record profile : Shows recording profile’s codec type.
 Overwrite : If the SD memory is full, this will delete old data and store new data in
replacement.
 Pre-alarm duration : Specify the time point before the occurrence of the alarm;
starting from the time point, the images will be transferred. You can specify up to
5 seconds before the occurrence of the alarm.
 Post-alarm duration : Specify the time point after the occurrence of the alarm; to
the specified time point, the images will be transferred. You can specify up to 120
seconds after the occurrence of the alarm.
 Normal : Make recording at a certain frame rate.
 Event : Set the recording type for a certain event that occurs.
4. Specify the <Normal record setup>.
 Always : Always save recorded video in the SD memory card.
 If set to Always, the activation time cannot be changed.
 Only scheduled time : Records only on the specified time of the specified day of week.
 [Clear (
)] : Reset all settings.
5. When done, click [Apply (
70_ setup screen
)].
Alarm input
You can set the alarm input type, activation time, and operation mode.
● SETUP SCREEN
1. From the Setup menu, select the
)> tab.
<Event (
2. Click <Event setup>.
3. Select <Alarm input> from <Event
action setup>.
4. Set whether or not to <Enable>.
5. Specify an input device.
 Type
- Normal open : It is normally open,
but if it is closed, an alarm will be
triggered.
- Normal close : It is normally closed,
but if it is open, an alarm will be
triggered.
6. Specify the <Activation time>.
 Always : Always check if an alarm occurs. It activates in operated mode when the
alarm occurs.
 If set to <Always>, the activation time cannot be changed.
 Only scheduled time : Check if an alarm occurs at a specified day of the week for
a specified time period. It activates in operated mode when the alarm occurs.
 [Clear (
)] : Reset all settings.
7. Specify an operation that will perform if an alarm occurs.
 FTP : Specify the use of FTP transfer in the alarm input setup.
 E-mail : Specify the use of email transfer in the alarm input setup.
 Record : Specify the use of recording in the alarm input setup.
 Alarm output : Select whether to set the alarm output if an alarm is incoming, and
specify the alarm output time.
 Goto preset : Moves to the specified preset location when setting the alarm input.
 Only if the camera pan/tilt receiver is installed, Goto preset is available.
8. When done, click [Apply (
)].
English _71
setup screen
Time schedule
You can set to save the video data at a certain interval as scheduled regardless of the
actual occurrence of the event.
1. From the Setup menu, select the
)> tab.
<Event (
2. Click <Event setup>.
3. Select <Time schedule> from <Event
action setup>.
4. Set whether or not to <Enable>.
5. Specify the <Transfer interval>.
6. Specify the activation time and
activation condition.
 For more information about <Activation
time> and <Action>, refer to “Alarm input”.
(page 71)
J
 The transfer interval setting value must be smaller than the preset activation interval to succeed in
image transmission.
7. When done, click [Apply (
72_ setup screen
)].
Tampering detection
You can set to detect tampering attempts and trigger events, such as sudden change
of camera’s framing direction, blocked lens and other overall change of scenes from the
video.
● SETUP SCREEN
1. From the Setup menu, select the
)> tab.
<Event (
2. Click <Event setup>.
3. Select <Tampering detection> from
<Event action setup>.
4. Set whether or not to <Enable>.
5. Set the tampering detection sensitivity.
The higher the sensitivity, detects the
minutest tampering attempts.
6. Specify the activation time and
activation condition.
 For more information about <Activation
time> and <Action>, refer to “Alarm input”.
(page 71)
7. When done, click [Apply (
J
)].
 The default tampering detection function may not work properly in the following cases:
- Under circumstances of simple background or low illumination and night time may lower the
detection sensitivity.
- A severe shaking of the camera or a drastic change to the illumination can be considered a
tampering by mistake.
- Detection of the tampering may take some time (maximum 5 seconds) right after the
tampering was made.
- Once a tampering is detected, the camera will resume a normal operating after a certain
stability time (approx. 5 seconds) during which no detection will be performed.
English _73
setup screen
Motion detection
Events of motion detection can be set to trigger event signal output.
1. From the Setup menu, select the
)> tab.
<Event (
2. Click <Event setup>.
3. Select <Motion detection> from
<Event action setup>.
4. Set whether or not to <Enable>.
5. Set <Sensitivity>, <Size> and <Area>.
6. Set whether to use <Detection result
overlay>.
When a motion is detected, its size and
position is marked with a rectangle on
the screen.
 Green : All targets detected as
moving.
7. Specify the activation time and
activation condition.
 For more information about <Activation
time> and <Action>, refer to “Alarm input”.
(page 71)
8. When done, click [Apply (
74_ setup screen
)].
J
 Before using, set the minimum and maximum motion sizes to suit desired motion range to be
detected.
 Detected size of an object may have difference with the actual size according to its shape.
 Up to 16 objects from the top side of the screen can be displayed.
- The object color or brightness is similar to the background.
- Small activities around the border area of the camera’s field of view.
- Multiple movements continue occurring at random due to a scene change, rapid lighting
changes or other reasons.
- A fixed object continues moving in the same position.
- Motions of less position changing such as approaching to the camera or fading away from the
camera.
- Moving object approaches to the camera too close
- An object hides other objects behind.
- Two or more objects overlap or one object divides in multiple portions.
- Too fast object (for a proper detection, one object should be found overlapping between
contiguous frames).
- Reflection / blur / shadow due to a strong light such as direct sunlight, illumination, or headlamp.
- In severe snow, rain, wind or in dawn / dusk.
English _75
● SETUP SCREEN
 In the following cases, motion detection function may be degraded or cause improper detection.
setup screen
To use Motion detection
It detects a motion that meets all conditions specified by sensitivity, size and area.
1. Select a motion detection mode.
2. Select <Sensitivity> tab to set the
sensitivity level. You can set the sensor’s
sensitivity to detect a motion out of the
background from the monitoring video.
J
 In a situation that definitely distinguishes
objects out of backgrounds, set this to a
low sensitivity level. For opposite case
that is hard to distinguish objects like low
illuminated situation, set this to a high
level.
3. Select <Size> tab.
You can limit the minimum/maximum
size of motion to be detected.
 Minimum Size : To set the minimum
size of detected motions, select
<Minimum Size> and then point
and drag to the desired size on the
screen using the mouse.
 Maximum Size : To set the maximum
size of detected motions, select
<Maximum Size> and then point
and drag to the desired size on the
screen with your mouse.
J
 Motions smaller than the specified minimum size or bigger than the maximum size are not
detected. To avoid unintended detections caused by great and small noises, set minimum/
maximum motion sizes appropriately in accordance to your environments.
Note that same motions on the same location can be differently detected in their detection size; it
is recommended to consider and include the tolerable difference when setting the minimum/
maximum detection sizes.
76_ setup screen
● SETUP SCREEN
4. Select <Area> tab.
You can specify an area on the screen
to include or exclude the area to/from
detection.
You can specify up to 4 areas.
 Detection area : Sets the entire
screen as excluded from detection,
and adds specified area as motion
detection area. Select 4 vertices in
the image with your mouse to specify
the detection area.
 Non detection area : Sets the entire
screen as motion detection area, and
excludes specified area as not to
be detected. Select 4 vertices in the
image with your mouse to specify the
non-detection area.
5. To delete an area, right click on the
screen to open popup context menu
and select Delete, and [OK] button.
6. When done, click [Apply (
)].
English _77
setup screen
Network disconnection
You can receive and save events of a physically disconnected network.
1. From the Setup menu, select the
)> tab.
<Event (
2. Click <Event setup>.
3. Select <Network disconnection> from
<Event action setup>.
4. Set whether or not to <Enable>.
5. Specify the activation time and
activation condition.
 For more information about <Activation
time> and <Action>, refer to “Alarm input”.
(page 71)
6. When done, click [Apply (
)].
Video Loss
You can set the alarm to be generated on a camera disconnection, which causes a video
loss.
1. From the Setup menu, select the
)> tab.
<Event (
2. Click <Event setup>.
3. Select <Video Loss > from <Event
action setup>.
4. Set whether or not to <Enable>.
5. Specify the activation time and activation
condition.
 For more information about <Activation
time> and <Action>, refer to “Alarm input”.
(page 71)
6. When done, click [Apply (
78_ setup screen
)].
Alarm output setup
1. From the Setup menu, select the
<Event (
)> tab.
3. Set the encoder’s type of alarm output.
 If you change the alarm output type, the alarm
out button on the monitoring page and alarm
output type displayed on Event Setup page will
be changed accordingly.
 Type
- Normal open : Considers “Open circuit” status of the sensor or alarm input device
as normal, and triggers alarm event if becomes “Closed circuit” status.
- Normal close : Considers “Closed circuit” status of the sensor or alarm input device
as normal, and triggers alarm event if becomes “Open circuit” status.
4. Set the alarm output button.
This setup is for the alarm output button in the monitoring page.
 Mode: Sets the alarm output method.
 There is difference between operations when clicked alarm output button while disabled.
- Pulse : It is activated during the time period specified by the duration (switching
interval) and then becomes inactive automatically.
- Active/Inactive : It maintains as activated until the user clicks the button again to
make it inactive.
 Duration : Set the alarm duration that maintains activated if the mode is set to
pulse, from 1 to 15 seconds.
5. When done, click [Apply (
)].
English _79
● SETUP SCREEN
2. Click <Alarm output setup>.
setup screen
SYSTEM SETUP
Product information
1. From the Setup menu, select the
<System (
)> tab.
2. Click <Product information>.
3. Check the encoder information, or
provide details according to your
network environment.
 Model : Model name of the product.
 Serial number : Product serial number.
 Device name : Provide a device name that will be displayed on the Live screen.
 Location : Specify the location where the encoder is installed.
 Description : Provide detailed information about the encoder location.
 Memo : Provide an explanation about the encoder for better understanding.
 Language : Select a preferred language for the Web Viewer OSD.
M
 The default language is set to <English>.
4. When done, click [Apply (
80_ setup screen
)].
Date & Time
1. From the Setup menu, select the
<System (
)> tab.
4. When done, click [Apply (
J
)].
 If you select the <Synchronize with PC viewer>, the standard timezone should be set the same
as the current timezone in PC.
English _81
● SETUP SCREEN
2. Click <Date & Time>.
3. Specify the time and date that will be
applied to the encoder.
 Current system time : Displays the
current time settings of your system.
 Timezone : Specify the local time
zone based on the GMT.
 Use daylight saving time :
If checked, the time will be set one
hour before the local time zone for
the specified time period.
This option will be displayed only in
areas where DST is applied.
 System time setup : Specify the time and date that will be applied to your system.
- Manual : Specify the time manually.
- Synchronize with NTP server : Sync with the time of the specified server address.
- Synchronize with PC viewer : Sets to the time of the computer connected.
setup screen
User
1. From the Setup menu, select the
<System (
)> tab.
2. Click <User>.
3. Provide the necessary user information.
 Administrator password change :
Change the password for the
administrator.
J
 For the security purposes, you are
recommended to use a combination
of numbers, alphabets uppercase
and lowercase and special characters
for your password.
 It is recommended to change your
password once every three months.
 The password length and limits are shown as follows.
- A combination of at least two types of upper case, lower case, numeric, and special
characters: 8 to 15 characters.
- Should be different from the ID.
- Cannot repeat the same letter, number of special characters more than three times.
- Cannot use three consecutive letters (e.g. abc, 123, 321, or ascii code values in the
sequential increasing or decreasing order)
- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/
- After the factory setting, the admin and user passwords are initialized. You need to reset
the password.
- When you access the product web page for the first time or access it after the initialization,
you will be moved to the admin password setting menu.
- In this menu, you need to login again with the new password before using the product web
page menus.
82_ setup screen
 If you try to login with the registered account, 5 or more consecutive password authentication
has failed, and then the account may be locked for thirty seconds.
 When the password is changed while multiple connections are active from a PC, the browser
may malfunction. In that case, reconnect to the server.
 Guest setup : If you select <Enable guest access>, the guest account can access
the Web viewer screen but can only view the live Viewer screen.
 The ID/password for the guest account is <guest/guest>, which cannot be changed.
 Authentication setup : If you select <Enable RTSP connection without
authentication>, you can access RTSP without logging in and view the video.
 Current users : If you select <Use>, you can set or change the user permissions.
 The administrator can set the audio input, audio output and alarm output permissions.
 Profile : If you select <Default>, you can only see the default profile video; if selecting <All>, you
can see the full profile videos.
J
 ONVIF functions available to a registered user allowed to use ONVIF functions are limited to those
of granted with permission.
 Video Transfer and Changing Video Information: Set the profile to <All>, and set Audio Input and
Audio Output.
 Video Transfer, Changing Video Information, Alarm Output : Set the profile to <All>, and select at
your preference for the rest.
 PTZ control : Select <PTZ>.
4. When done, click [Apply (
)].
English _83
● SETUP SCREEN
- If the existing password is not matched, when you change the admin password, you
cannot change the password.
- After changing your password, if there is a product connected to a CMS or NVR client,
then you need to re-register it with the newly changed password. If the product is still
connected with the same password, then the account may be locked because a client
uses the previous password.
setup screen
Upgrade / Reboot
1. From the Setup menu, select the
<System (
)> tab.
2. Click <Upgrade / Reboot>.
3. Select a desired item and set it
appropriately.
 Upgrade : Performs upgrading the
system.
 Factory default : Resets the system
to the factory default.
- Except network parameter : Initialize all setup parameters except for network
setup.
- All : Resets all settings including the encoder settings. (however, the log
information will not be reset)
 The IP addressing system will be defaulted to DHCP if you reset the encoder. If no DHCP server
is found, the previous settings will be restored automatically.
 Configuration backup & Restore : Backs up the current system settings before
performing the restoration process. The system is automatically restarts after
backup or restoration.
 Restart : Restarts the system.
To perform the upgrade
1. Click [Upgrade].
2. Click [Browse] and specify a file to
upgrade.
3. Click [Send].
4. The “Upgrade” dialog appears where
the progression will be shown in the
bottom.
5. Once completed upgrading, the
browser exits and the encoder restarts.
84_ setup screen
M
 It may take a max of 20 minutes for the upgrade process.
If you forcibly terminate the upgrade process, upgrade will not be completed properly.
 During restarting the system, accessing with web viewer will not be made.
 You can download the latest version from the Samsung web site (www.samsungcctv.com).
● SETUP SCREEN
To back up the current settings
1. Click [Backup].
The Save As dialog should appear.
2. Specify the backup path with a proper
file name, and click [Save].
The backup file will be saved to the
specified path in the format of “.bin”.
To restore the backup settings
1. To restore the backup settings, click
[Restore].
2. Select a backup file and click [Open].
M
 If you perform the backup or restoration,
the web browser will be closed and the
encoder will reboots.
English _85
setup screen
Log
You can check the system log or event log.
1. From the Setup menu, select the
)> tab.
<System (
2. Click <Log>.
3. Select a log type.
 System : You can check the system
logs where any system changes
are recorded including the time
information.
 Event : You can check the event logs
including the time information.
4. From the right log list, select an item to
search for.
 If you select <All> in the top left dropdown list, all logs for the applicable log type
will be displayed.
5. If one page can not display all the logs available, use the bottom buttons to move to
the previous, next, or the last item.
M
 If you want to view the details of a log, click [Info (
)] in the right column of the log; the log
information will be shown in the bottom pane.
 Each page displays 15 logs with the latest one displayed at the top.
 The event/system log list can contain up to 1000 logs; after that, the existing logs will be deleted
from the oldest one each time a new log is created.
86_ setup screen
Profile access
You can check the profile information.
● SETUP SCREEN
1. From the Setup menu, select the
)> tab.
<System (
2. Click <Profile access>.
 Profile access : Show the information
of the newly added profile.
- Profile : Show the information of the
newly added codec.
- Bitrate(kbps) : Show both the actual
bit rate and the set bit rate.
- Framerate(fps) : Show both the actual frame rate and the set frame rate.
- ATC(%) : Show the ATC status.
- Concurrent users count : Show the number of concurrent users who access the
profile.
 Current users : Shows information on users accessing web viewer and displaying
monitoring video.
- Profile : Show the name of the profile accessed by the user.
- Bitrate(kbps) : Show the current bit rate.
- Network connection status : You can check the network connection status.
- IP : Show the IP address of the current user.
M
 To check information on the profile currently used, click <Profile access> again to refresh it.
English _87
appendix
SPECIFICATION
Items
Description
Video In
CVBS : 1.0 Vp-p / 75Ω composite, NTSC/PAL Auto Detection
Video Out
CVBS : 1.0 Vp-p / 75Ω composite, Loop out
De-interlacing Filter
Built-in
Event Trigger
Motion Detection, Alarm Input, Video Loss, Tampering, Network
Disconnection
Alarm I/O
Input 1ea / Output 1ea (Relay)
Remote Control
Interface
RS-485
RS-485 Protocol
Samsung-T/E, Pelco-P/D, Panasonic, Honeywell, AD, Vicon, GE,
Bosch, Sungjin
Ethernet
RJ-45 (10/100BASE-T)
Video Compression
Format
H.264, MPEG-4, Motion JPEG
Resolution
NT : 704x480, 640x480, 352x240, 320x240
PAL : 704x576, 640x480, 352x288, 320x240
Max. Framerate
NT : 30fps / PAL : 25fps
Video Quality
Adjustment
H.264/MPEG-4 : Compression Level, Target Bitrate Level Control
Motion JPEG : Quality Level Control
Bitrate Control Method
H.264/MPEG-4 : CBR or VBR
Motion JPEG : VBR
Streaming Capability
Multiple Streaming (Up to 10 Profiles)
Audio I/O
1ea Line in / 1ea Line out
Audio Compression
Format
G.711 μ-law
Operational
Network
Audio Communication Bi-directional audio
IP
88_ appendix
IPv4, IPv6
Items
Environmental
Protocol
Security
HTTPS(SSL) Login Authentication
Digest Login Authentication
IP Address Filtering
User access Log
802.1x
Streaming Method
Unicast / Multicast
Max. User Access
10 users at Unicast Mode
Memory Slot
SD/SDHC Memory Slot
ONVIF Conformance
Yes
Web Viewer
Supported OS : Window XP / VISTA / 7, Mac OS X(10.7 or higher)
Supported Browser : Internet Explorer (7.0 or higher),
Firefox (9.0 or higher), Chrome (15.0 or higher),
Safari (5.1 or higher)
Central Management
Software
SmartViewer 4.0, NET-i viewer
● APPENDIX
Network
Description
TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTSP, NTP, HTTP, HTTPS, SSL,
DHCP, PPPoE, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2), ARP,
DNS, DDNS, QoS, UPnP
Operating Temperature
-10°C ~ +50°C (+14°F ~ +122°F) / 20% ~ 80% RH
/ Humidity
Ingress Protection
-
Input Voltage / Current 12V DC, PoE(IEEE802.3af)
Electrical
Mechanical
Power Consumption
Max. 4W
Color / Material
Silver / Metal
Dimensions (WxHxD)
W87.14 x H43.8 x D128.0mm (3.43" x 1.72" x 5.04")
Weight
391g
English _89
appendix
PRODUCT OVERVIEW
Unit : mm (inch)
43.8 (1.72")
147.5 (5.80")
128.0 (5.04")
87.14 (3.43")
90_ appendix
TROUBLESHOOTING
PROBLEM
SOLUTION
I can’t access the network video
encoder from a web browser.
 Check to make sure that all network cables have been connected
properly.
 If connected using DHCP, verify that the network video encoder is able to
acquire dynamic IP addresses without any problem.
 If the network video encoder is connected to a router, verify that port
forwarding is properly configured.
 The existing Web Viewer connection can be expired if the network setting
or configuration of the network video encoder is modified by another user.
Viewer got disconnected during
monitoring.
 Check all network connections.
I cannot connect to the system
using a tab browser of Internet
Explorer 7.0.
 An error may be generated when connecting with a new window or
tab since the cookie data are shared. Do not use a new window or tab,
select “File  New session”.
The network video encoder
connected to the network is
not detected in the IP installer
program.
 Turn off the firewall settings on your PC and then search the network
video encoder again.
Images overlap.
 Check whether two or more network video encoders are set to a single
multicast address instead of different addresses. If a single address is
used for multiple network video encoders, the images may overlap.
No image appears.
 If the transmission method is set to multicast, check whether there is a
router that supports multicast in the LAN the network video encoder is
connected to.
 Web Viewer connection may be interrupted by poor network traffic or
condition if the network video encoder is connected to a PPPoE network.
English _91
● APPENDIX
 Check whether the Network settings of the network video encoder are
valid and correct.
appendix
PROBLEM
SOLUTION
Cannot record into the SD memory  Check if the memory card is defective.
card.
 Check if the write protection tab of the memory card is set to “LOCK”.
SD memory indicator does not
 Check if the memory card is defective.
turn on even when the SD memory
 Check if the device to used in <Setup>  <Event>  <Storage> menu.
card is inserted.
SD memory card is inserted but
the network video encoder does
not operate properly.
Cannot format the SD memory
card.
92_ appendix
 Check if the memory card is inserted in the proper direction. Operation
of memory card that is formatted by other devices is not guaranteed with
this network video encoder unit.
 Format the memory card again in <Setup>  <Event>  <Storage>
menu.
 Check if the write protection tab of the memory card is set to “LOCK”.
OPEN SOURCE LICENSE NOTIFICATION ON THE PRODUCT
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain
the complete Corresponding Source code from us for a period of three years after our last shipment of this product by
sending email to help.cctv@samsung.com
If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of
physically performing source distribution might be charged.
• GPL Software : alsa-lib-1.0.12, alsa-utils-1.0.12, bash-4.1(ftp://ftp.gnu.org/gnu/bash/),
busybox-1.15.3(http://www.busybox.net/), ethtool-3.5, iproute-1.15.3, iptables-1.3.7,
mii-diag-2.11, wpa_supplicant-0.7.3(http://hostap.epitest.fi/wpa_supplicant/)
• LGPL Software : virtualawesome
• MPL Software : Mozilla Firefox(http://www.mozilla.org/products/firebird/)
• BSD2.0: lighttpd(http://www.lighttpd.net/), ppp-2.4.2(http://ppp.samba.org/),
net-snmp-5.4.1(http://www.net-snmp.org/), game-ws(https://code.google.com/p/game-ws/),
MiniUPnP Project Client(http://miniupnp.tuxfamily.org/)
• MIT License: libxml2-2.7.6, ncurses-5.7, Gimpact Collision Kernel, Acewidget, bettermeans, jquery-ui, libxml,
Mesa3D-MesaLib,mwEmbed,OpenGL Samples Pack, Wide Studio, xorg-server,
dropbear-0.52(https://matt.ucc.asn.au/dropbear/dropbear.html)
• OpenSSL License: openssl-0.9.8e(http://www.openssl.org/)
• Bzip2 License : bzip2-1.0.5
• JPEG License : Code project – Generating Outline OpenGL, libjpeg
The GNU General Public License (GPL 2.0)
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim copies
of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the
GNU General Public License is intended to guarantee your
freedom to share and change free software--to make sure
the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s
software and to any other program whose authors commit to
using it. (Some other Free Software Foundation software is
covered by the GNU Library General Public License instead.)
You can apply it to your programs, too.
When we speak of free software, we are referring to freedom,
not price. Our General Public Licenses are designed to make
sure that you have the freedom to distribute copies of free
software (and charge for this service if you wish), that you
receive source code or can get it if you want it, that you can
change the software or use pieces of it in new free programs;
and that you know you can do these things.
To protect your rights, we need to make restrictions that
forbid anyone to deny you these rights or to ask you to
surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the
software, or if you modify it.
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must give the recipients all
the rights that you have. You must make sure that they, too,
receive or can get the source code. And you must show
them these terms so they know their rights.
else and passed on, we want its recipients to know that what
they have is not the original, so that any problems introduced
by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software
patents. We wish to avoid the danger that redistributors of a
free program will individually obtain patent licenses, in effect
making the program proprietary. To prevent this, we have
made it clear that any patent must be licensed for everyone’s
free use or not licensed at all.
The precise terms and conditions for copying, distribution
and modification follow.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work
which contains a notice placed by the copyright holder
saying it may be distributed under the terms of this
General Public License. The “Program”, below, refers to
any such program or work, and a “work based on the
Program” means either the Program or any derivative
work under copyright law: that is to say, a work containing
the Program or a portion of it, either verbatim or with
modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the
term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification
are not covered by this License; they are outside its scope.
The act of running the Program is not restricted, and the
output from the Program is covered only if its contents
constitute a work based on the Program (independent of
having been made by running the Program). Whether that is
true depends on what the Program does.
We protect your rights with two steps: (1) copyright the
software, and (2) offer you this license which gives you legal
permission to copy, distribute and/or modify the software.
1. You may copy and distribute verbatim copies of the
Program’s source code as you receive it, in any medium,
provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice and
disclaimer of warranty; keep intact all the notices that refer
to this License and to the absence of any warranty; and
give any other recipients of the Program a copy of this
License along with the Program.
Also, for each author’s protection and ours, we want to make
certain that everyone understands that there is no warranty
for this free software. If the software is modified by someone
You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies of the Program
or any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications or
work under the terms of Section 1 above, provided that
you also meet all of these conditions:
a) You must cause the modified files to carry prominent
notices stating that you changed the files and the date
of any change.
b) You must cause any work that you distribute or
publish, that in whole or in part contains or is derived
from the Program or any part thereof, to be licensed
as a whole at no charge to all third parties under the
terms of this License.
c) If the modified program normally reads commands
interactively when run, you must cause it, when started
running for such interactive use in the most ordinary
way, to print or display an announcement including
an appropriate copyright notice and a notice that
there is no warranty (or else, saying that you provide a
warranty) and that users may redistribute the program
under these conditions, and telling the user how to
view a copy of this License. (Exception: if the Program
itself is interactive but does not normally print such an
announcement, your work based on the Program is
not required to print an announcement.)
These requirements apply to the modified work as a whole.
If identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent
and separate works in themselves, then this License, and its
terms, do not apply to those sections when you distribute
them as separate works. But when you distribute the same
sections as part of a whole which is a work based on the
Program, the distribution of the whole must be on the terms
of this License, whose permissions for other licensees
extend to the entire whole, and thus to each and every part
regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or
contest your rights to work written entirely by you; rather,
the intent is to exercise the right to control the distribution of
derivative or collective works based on the Program.
In addition, mere aggregation of another work not based
on the Program with the Program (or with a work based
on the Program) on a volume of a storage or distribution
medium does not bring the other work under the scope of
this License.
3. You may copy and distribute the Program (or a work
based on it, under Section 2) in object code or executable
form under the terms of Sections 1 and 2 above provided
that you also do one of the following:
a) Accompany it with the complete corresponding
machine-readable source code, which must be
distributed under the terms of Sections 1 and 2
above on a medium customarily used for software
interchange; or,
b) Accompany it with a written offer, valid for at least
three years, to give any third party, for a charge no
more than your cost of physically performing source
distribution, a complete machine-readable copy of the
corresponding source code, to be distributed under
the terms of Sections 1 and 2 above on a medium
customarily used for software interchange; or,
c) Accompany it with the information you received as
to the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial
distribution and only if you received the program in
object code or executable form with such an offer, in
accord with Subsection b above.)
The source code for a work means the preferred form of
the work for making modifications to it. For an executable
work, complete source code means all the source code
for all modules it contains, plus any associated interface
definition files, plus the scripts used to control compilation
and installation of the executable. However, as a special
exception, the source code distributed need not include
anything that is normally distributed (in either source or binary
form) with the major components (compiler, kernel, and so
on) of the operating system on which the executable runs,
unless that component itself accompanies the executable.
If distribution of executable or object code is made by
offering access to copy from a designated place, then
offering equivalent access to copy the source code from the
same place counts as distribution of the source code, even
though third parties are not compelled to copy the source
along with the object code.
4. You may not copy, modify, sublicense, or distribute the
Program except as expressly provided under this License.
Any attempt otherwise to copy, modify, sublicense or
distribute the Program is void, and will automatically
terminate your rights under this License. However, parties
who have received copies, or rights, from you under this
License will not have their licenses terminated so long as
such parties remain in full compliance.
5. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Program or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying
or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License
to do so, and all its terms and conditions for copying,
distributing or modifying the Program or works based
on it.
6. Each time you redistribute the Program (or any work
based on the Program), the recipient automatically
receives a license from the original licensor to copy,
distribute or modify the Program subject to these
terms and conditions. You may not impose any further
restrictions on the recipients’ exercise of the rights granted
herein. You are not responsible for enforcing compliance
by third parties to this License.
7. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by
court order, agreement or otherwise) that contradict the
conditions of this License, they do not excuse you from
the conditions of this License. If you cannot distribute so
as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a
consequence you may not distribute the Program at all.
For example, if a patent license would not permit royaltyfree redistribution of the Program by all those who receive
copies directly or indirectly through you, then the only
way you could satisfy both it and this License would be to
refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply and the section as a whole is intended
to apply in other circumstances.
It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose
of protecting the integrity of the free software distribution
system, which is implemented by public license practices.
Many people have made generous contributions to the
wide range of software distributed through that system in
reliance on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to distribute
software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places
the Program under this License may add an explicit
geographical distribution limitation excluding those
countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the body
of this License.
9. The Free Software Foundation may publish revised and/
or new versions of the General Public License from time
to time. Such new versions will be similar in spirit to the
present version, but may differ in detail to address new
problems or concerns.
Each version is given a distinguishing version number. If the
Program specifies a version number of this License which
applies to it and “any later version”, you have the option of
following the terms and conditions either of that version or of
any later version published by the Free Software Foundation.
If the Program does not specify a version number of this
License, you may choose any version ever published by the
Free Software Foundation.
10. If you wish to incorporate parts of the Program into
other free programs whose distribution conditions are
different, write to the author to ask for permission. For
software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be
guided by the two goals of preserving the free status of
all derivatives of our free software and of promoting the
sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE
OF CHARGE, THERE IS NO WARRANTY FOR
THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS
AND/OR OTHER PARTIES PROVIDE THE PROGRAM
“AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE PROGRAM IS WITH
YOU. SHOULD THE PROGRAM PROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES
OR A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER
OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New
Programs
If you develop a new program, and you want it to be of
the greatest possible use to the public, the best way to
achieve this is to make it free software which everyone can
redistribute and change under these terms.
To do so, attach the following notices to the program. It is
safest to attach them to the start of each source file to most
effectively convey the exclusion of warranty; and each file
should have at least the “copyright” line and a pointer to
where the full notice is found.
One line to give the program’s name and a brief idea of
what it does.
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
as published by the Free Software Foundation; either version
2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be
useful, but WITHOUT ANY WARRANTY; without even the
implied warranty of MERCHANTABILITY or FITNESS FOR
A PARTICULAR PURPOSE. See the GNU General Public
License for more details.
You should have received a copy of the GNU General Public
License along with this program; if not, write to the Free
Software Foundation, Inc., 59 Temple Place, Suite 330,
Boston, MA 02111-1307 USA
Also add information on how to contact you by electronic
and paper mail.
If the program is interactive, make it output a short notice like
this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY;
for details type `show w’. This is free software, and you are
welcome to redistribute it under certain conditions; type
`show c’ for details.
The hypothetical commands `show w’ and `show c’ should
show the appropriate parts of the General Public License.
Of course, the commands you use may be called something
other than `show w’ and `show c’; they could even be
mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a
programmer) or your school, if any, to sign a “copyright
disclaimer” for the program, if necessary. Here is a sample;
alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the
program `Gnomovision’ (which makes passes at compilers)
written by James Hacker.
signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating
your program into proprietary programs. If your program is a
subroutine library, you may consider it more useful to permit
linking proprietary applications with the library. If this is what
you want to do, use the GNU Library General Public License
instead of this License.
GNU GENERAL PUBLIC LICENSE (GPL 3.0)
Version 3, 29 June 2007
Copyright (C) 2007 Free Software Foundation, Inc. http://fsf.
org/ Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed. Preamble The GNU General Public License is a
free, copyleft license for software and other kinds of works.
The licenses for most software and other practical works are
designed to take away your freedom to share and change
the works. By contrast, the GNU General Public License is
intended to guarantee your freedom to share and change all
versions of a program--to make sure it remains free software
for all its users. We, the Free Software Foundation, use
the GNU General Public License for most of our software;
it applies also to any other work released this way by its
authors. You can apply it to your programs, too. When we
speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make
sure that you have the freedom to distribute copies of free
software (and charge for them if you wish), that you receive
source code or can get it if you want it, that you can change
the software or use pieces of it in new free programs,
and that you know you can do these things. To protect your
rights, we need to prevent others from denying you these
rights or asking you to surrender the rights. Therefore, you
have certain responsibilities if you distribute copies of the
software, or if you modify it: responsibilities to respect the
freedom of others.
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must pass on to the
recipients the same freedoms that you received. You must
make sure that they, too, receive or can get the
source code. And you must show them these terms so they
know their rights.
A “covered work” means either the unmodified Program
or a work based on the Program. To “propagate” a work
means to do anything with it that, without permission, would
make you directly or secondarily liable for infringement under
applicable copyright law, except executing it on a computer
or modifying a private copy. Propagation includes copying,
distribution (with or without modification), making available to
the public, and in some countries other activities as well. To
“convey” a work means any kind of propagation that enables
other parties to make or receive copies. Mere interaction with
a user through a computer network, with no transfer of a
copy, is not conveying. An interactive user interface displays
“Appropriate Legal Notices” to the extent that it includes a
convenient and prominently visible feature that (1)displays
an appropriate copyright notice, and (2) tells the user that
there is no warranty for the work (except to the extent that
warranties are provided), that licensees may convey the
work under this License, and how to view a copy of this
License. If the interface presents a list of user commands or
options, such as a menu, a prominent item in the list meets
this criterion.
1. Source Code.
The “source code” for a work means the preferred form of
the work for making modifications to it. “Object code” means
any non-source form of a work.
TERMS AND CONDITIONS
A “Standard Interface” means an interface that either is
an official standard defined by a recognized standards
body, or, in the case of interfaces specified for a particular
programming language, one that is widely used among
developers working in that language. The “System Libraries”
of an executable work include anything, other than the
work as a whole, that (a) is included in the normal form of
packaging a Major Component, but which is not part of
that Major Component, and (b) serves only to enable use
of the work with that Major Component, or to implement a
Standard Interface for which an implementation is available
to the public in source code form. A “Major Component”, in
this context, means a major essential component (kernel,
window system, and so on) of the specific operating system
(if any) on which the executable work runs, or a compiler
used to produce the work, or an object code interpreter
used to run it. The “Corresponding Source” for a work in
object code form means all the source code needed to
generate, install, and (for an executable work) run the object
code and to modify the work, including scripts to control
those activities. However, it does not include the work’s
System Libraries, or general-purpose tools or generally
available free programs which are used unmodified in
performing those activities but which are not part of the
work. For example, Corresponding Source includes interface
definition files associated with source files for the work,
and the source code for shared libraries and dynamically
linked subprograms that the work is specifically designed to
require, such as by intimate data communication or control
flow between those subprograms and other parts of the
work. The Corresponding Source need not include anything
that users can regenerate automatically from other parts of
the Corresponding Source. The Corresponding Source for a
work in source code form is that same work.
0. Definitions.
2. Basic Permissions.
“This License” refers to version 3 of the GNU General
Public License. “Copyright” also means copyright-like laws
that apply to other kinds of works, such as semiconductor
masks. “The Program” refers to any copyrightable work
licensed under this License. Each licensee is addressed as
“you”. “Licensees” and “recipients” may be individuals or
organizations. To “modify” a work means to copy from or
adapt all or part of the work in a fashion requiring copyright
permission, other than the making of an exact copy. The
resulting work is called a “modified version” of the earlier
work or a work “based on” the earlier work.
All rights granted under this License are granted for the term
of copyright on the Program, and are irrevocable provided
the stated conditions are met. This License explicitly affirms
your unlimited permission to run the unmodified Program.
The output from running a covered work is covered by this
License only if the output, given its content, constitutes a
covered work. This License acknowledges your rights of
fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you
do not convey, without conditions so long as your license
otherwise remains in force. You may convey covered
works to others for the sole purpose of having them make
Developers that use the GNU GPL protect your rights with
two steps: (1)assert copyright on the software, and (2)
offer you this License giving you legal permission to copy,
distribute and/or modify it. For the developers’ and authors’
protection, the GPL clearly explains that there is no warranty
for this free software. For both users’ and authors’ sake, the
GPL requires that modified versions be marked as changed,
so that their problems will not be attributed erroneously to
authors of previous versions. Some devices are designed to
deny users access to install or run modified versions of the
software inside them, although the manufacturer can do so.
This is fundamentally incompatible with the aim of protecting
users’ freedom to change the software. The systematic
pattern of such abuse occurs in the area of products
for individuals to use, which is precisely where it is most
unacceptable. Therefore, we have designed this version of
the GPL to prohibit the practice for those products. If such
problems arise substantially in other domains, we stand
ready to extend this provision to those domains in future
versions of the GPL, as needed to protect the freedom of
users. Finally, every program is threatened constantly by
software patents. States should not allow patents to restrict
development and use of software on general-purpose
computers, but in those that do, we wish to avoid the special
danger that patents applied to a free program could make it
effectively proprietary. To prevent this, the GPL assures that
patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution
and modification follow.
modifications exclusively for you, or provide you with facilities
for running those works, provided that you comply with the
terms of this License in conveying all material for which you
do not control copyright. Those thus making or running the
covered works for you must do so exclusively on your behalf,
under your direction and control, on terms that prohibit
them from making any copies of your copyrighted material
outside their relationship with you. Conveying under any
other circumstances is permitted solely under the conditions
stated below. Sublicensing is not allowed; section 10 makes
it unnecessary.
3. Protecting Users’ Legal Rights From AntiCircumvention Law.
No covered work shall be deemed part of an effective
technological measure under any applicable law fulfilling
obligations under article 11 of the WIPO copyright treaty
adopted on 20 December 1996, or similar laws prohibiting or
restricting circumvention of such measures.
When you convey a covered work, you waive any legal
power to forbid circumvention of technological measures to
the extent such circumvention is effected by exercising rights
under this License with respect to the covered work, and
you disclaim any intention to limit operation or modification of
the work as a means of enforcing, against the work’s users,
your or third parties’ legal rights to forbid circumvention of
technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source
code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an
appropriate copyright notice;
keep intact all notices stating that this License and any
non-permissive terms added in accord with section 7 apply
to the code; keep intact all notices of the absence of any
warranty; and give all recipients a copy of this License along
with the Program.
You may charge any price or no price for each copy that
you convey,
and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the
modifications to produce it from the Program, in the form of
source code under the terms of section 4, provided that you
also meet all of these conditions:
a) The work must carry prominent notices stating that you
modified it, and giving a relevant date.
b) The work must carry prominent notices stating that
it is released under this License and any conditions
added under section 7. This requirement modifies the
requirement in section 4 to “keep intact all notices”.
c) You must license the entire work, as a whole, under
this License to anyone who comes into possession of
a copy. This License will therefore apply, along with any
applicable section 7 additional terms, to the whole of
the work, and all its parts, regardless of how they are
packaged. This License gives no permission to license
the work in any other way, but it does not invalidate
such permission if you have separately received it.
d) If the work has interactive user interfaces, each must
display Appropriate Legal Notices; however, if the
Program has interactive interfaces that do not display
Appropriate Legal Notices, your work need not make
them do so.
A compilation of a covered work with other separate and
independent works, which are not by their nature extensions
of the covered work, and which are not combined with it
such as to form a larger program, in or on a volume of a
storage or distribution medium, is called an “aggregate” if the
compilation and its resulting copyright are not used to limit
the access or legal rights of the compilation’s users beyond
what the individual works permit. Inclusion of a covered work
in an aggregate does not cause this License to apply to the
other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under
the terms of sections 4 and 5, provided that you also convey
the machine-readable Corresponding Source under the
terms of this License, in one of these ways:
a) Convey the object code in, or embodied in, a physical
product (including a physical distribution medium),
accompanied by the Corresponding Source fixed on a
durable physical medium customarily used for software
interchange.
b) Convey the object code in, or embodied in, a physical
product (including a physical distribution medium),
accompanied by a written offer, valid for at least three
years and valid for as long as you offer spare parts
or customer support for that product model, to give
anyone who possesses the object code either (1) a
copy of the Corresponding Source for all the software
in the product that is covered by this License, on a
durable physical medium customarily used for software
interchange, for a price no more than your reasonable
cost of physically performing this conveying of source,
or (2) access to copy the Corresponding Source from a
network server at no charge.
c) Convey individual copies of the object code with a
copy of the written offer to provide the Corresponding
Source. This alternative is allowed only occasionally
and noncommercially, and only if you received
the object code with such an offer, in accord with
subsection 6b.
d) Convey the object code by offering access from a
designated place (gratis or for a charge), and offer
equivalent access to the Corresponding Source in
the same way through the same place at no further
charge. You need not require recipients to copy the
Corresponding Source along with the object code. If
the place to copy the object code is a network server,
the Corresponding Source may be on a different
server (operated by you or a third party) that supports
equivalent copying facilities, provided you maintain
clear directions next to the object code saying where
to find the Corresponding Source. Regardless of what
server hosts the Corresponding Source, you remain
obligated to ensure that it is available for as long as
needed to satisfy these requirements.
e) Convey the object code using peer-to-peer
transmission, provided you inform other peers where
the object code and Corresponding Source of the work
are being offered to the general public at no charge
under subsection 6d.
A separable portion of the object code, whose source code
is excluded from the Corresponding Source as a System
Library, need not be included in conveying the object code
work.
A “User Product” is either (1) a “consumer product”, which
means any tangible personal property which is normally
used for personal, family, or household purposes, or (2)
anything designed or sold for incorporation into a dwelling.
In determining whether a product is a consumer product,
doubtful cases shall be resolved in favor of coverage. For
a particular product received by a particular user, “normally
used” refers to a typical or common use of that class of
product, regardless of the status of the particular user or
of the way in which the particular user actually uses, or
expects or is expected to use, the product. A product is a
consumer product regardless of whether the product has
substantial commercial, industrial or non-consumer uses,
unless such uses represent the only significant mode of use
of the product.
c) Prohibiting misrepresentation of the origin of that
material, or requiring that modified versions of such
material be marked in reasonable ways as different
from the original version; or
“Installation Information” for a User Product means
any methods, procedures, authorization keys, or other
information required to install and execute modified versions
of a covered work in that User Product from a modified
version of its Corresponding Source. The information must
suffice to ensure that the continued functioning of the
modified object code is in no case prevented or interfered
with solely because modification has been made.
d) Limiting the use for publicity purposes of names of
licensors or authors of the material; or
If you convey an object code work under this section in,
or with, or specifically for use in, a User Product, and the
conveying occurs as part of a transaction in which the right
of possession and use of the User Product is transferred to
the recipient in perpetuity or for a fixed term (regardless of
how the transaction is characterized), the Corresponding
Source conveyed under this section must be accompanied
by the Installation Information. But this requirement does
not apply if neither you nor any third party retains the ability
to install modified object code on the User Product (for
example, the work has been installed in ROM).
The requirement to provide Installation Information does not
include a requirement to continue to provide support service,
warranty, or updates for a work that has been modified or
installed by the recipient, or for the User Product in which it
has been modified or installed. Access to a network may be
denied when the modification itself materially and adversely
affects the operation of the network or violates the rules and
protocols for communication across the network.
Corresponding Source conveyed, and Installation Information
provided, in accord with this section must be in a format that
is publicly documented (and with an implementation available
to the public in source code form), and must require no
special password or key for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the
terms of this License by making exceptions from one or
more of its conditions.
Additional permissions that are applicable to the entire
Program shall be treated as though they were included
in this License, to the extent that they are valid under
applicable law. If additional permissions apply only to part of
the Program, that part may be used separately under those
permissions, but the entire Program remains governed by
this License without regard to the additional permissions.
When you convey a copy of a covered work, you may at
your option remove any additional permissions from that
copy, or from any part of it.
(Additional permissions may be written to require their
own removal in certain cases when you modify the work.)
You may place additional permissions on material, added
by you to a covered work, for which you have or can give
appropriate copyright permission.
Notwithstanding any other provision of this License, for
material you add to a covered work, you may (if authorized
by the copyright holders of that material) supplement the
terms of this License with terms:
a) Disclaiming warranty or limiting liability differently from
the terms of sections 15 and 16 of this License; or
b) Requiring preservation of specified reasonable legal
notices or author attributions in that material or in
the Appropriate Legal Notices displayed by works
containing it; or
e) Declining to grant rights under trademark law for use of
some trade names, trademarks, or service marks; or
f) Requiring indemnification of licensors and authors of
that material by anyone who conveys the material (or
modified versions of it)
with contractual assumptions of liability to the recipient,
for any liability that these contractual assumptions directly
impose on those licensors and authors.
All other non-permissive additional terms are considered
“further restrictions” within the meaning of section 10. If
the Program as you received it, or any part of it, contains a
notice stating that it is governed by this License along with a
term that is a further restriction, you may remove that term. If
a license document contains a further restriction but permits
relicensing or conveying under this License, you may add
to a covered work material governed by the terms of that
license document, provided that the further restriction does
not survive such relicensing or conveying.
If you add terms to a covered work in accord with this
section, you must place, in the relevant source files, a
statement of the additional terms that apply to those files, or
a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be
stated in the form of a separately written license, or stated as
exceptions; the above requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except
as expressly provided under this License. Any attempt
otherwise to propagate or modify it is void, and will
automatically terminate your rights under this License
(including any patent licenses granted under the third
paragraph of section 11).
However, if you cease all violation of this License, then your
license from a particular copyright holder is reinstated (a)
provisionally, unless and until the copyright holder explicitly
and finally terminates your license, and (b) permanently, if the
copyright holder fails to notify you of the violation by some
reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is
reinstated permanently if the copyright holder notifies you of
the violation by some reasonable means, this is the first time
you have received notice of violation of this License (for any
work) from that copyright holder, and you cure the violation
prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not
terminate the licenses of parties who have received copies
or rights from you under this License. If your rights have
been terminated and not permanently reinstated, you do not
qualify to receive new licenses for the same material under
section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to
receive or run a copy of the Program. Ancillary propagation
of a covered work occurring solely as a consequence of
using peer-to-peer transmission to receive a copy likewise
does not require acceptance. However, nothing other than
this License grants you permission to propagate or modify
any covered work. These actions infringe copyright if you do
not accept this License.
Therefore, by modifying or propagating a covered work, you
indicate your acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient
automatically receives a license from the original licensors, to
run, modify and propagate that work, subject to this License.
You are not responsible for enforcing compliance by third
parties with this License.
An “entity transaction” is a transaction transferring control
of an organization, or substantially all assets of one, or
subdividing an organization, or merging organizations.
If propagation of a covered work results from an entity
transaction, each party to that transaction who receives a
copy of the work also receives whatever licenses to the work
the party’s predecessor in interest had or could give under
the previous paragraph, plus a right to possession of the
Corresponding Source of the work from the predecessor
in interest, if the predecessor has it or can get it with
reasonable efforts.
You may not impose any further restrictions on the exercise
of the rights granted or affirmed under this License. For
example, you may not impose a license fee, royalty, or other
charge for exercise of rights granted under this License,
and you may not initiate litigation (including a cross-claim
or counterclaim in a lawsuit) alleging that any patent claim
is infringed by making, using, selling, offering for sale, or
importing the Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use
under this License of the Program or a work on which the
Program is based. The work thus licensed is called the
contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims
owned or controlled by the contributor, whether already
acquired or hereafter acquired, that would be infringed by
some manner, permitted by this License, of making, using,
or selling its contributor version, but do not include claims
that would be infringed only as a consequence of further
modification of the contributor version. For purposes of
this definition, “control” includes the right to grant patent
sublicenses in a manner consistent with the requirements
of this License.
Each contributor grants you a non-exclusive, worldwide,
royalty-free patent license under the contributor’s essential
patent claims, to make, use, sell, offer for sale, import and
otherwise run, modify and propagate the contents of its
contributor version.
In the following three paragraphs, a “patent license” is any
express agreement or commitment, however denominated,
not to enforce a patent (such as an express permission
to practice a patent or covenant not to sue for patent
infringement). To “grant” such a patent license to a party
means to make such an agreement or commitment not to
enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent
license, and the Corresponding Source of the work is not
available for anyone to copy, free of charge and under the
terms of this License, through a publicly available network
server or other readily accessible means, then you must
either (1) cause the Corresponding Source to be so available,
or (2) arrange to deprive yourself of the benefit of the patent
license for this particular work, or (3) arrange, in a manner
consistent with the requirements of this License, to extend
the patent license to downstream recipients. “Knowingly
relying” means you have actual knowledge that, but for the
patent license, your conveying the covered work in a country,
or your recipient’s use of the covered work in a country,
would infringe one or more identifiable patents in that country
that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction
or arrangement, you convey, or propagate by procuring
conveyance of, a covered work, and grant a patent license
to some of the parties receiving the covered work authorizing
them to use, propagate, modify or convey a specific copy
of the covered work, then the patent license you grant is
automatically extended to all recipients of the covered work
and works based on it.
A patent license is “discriminatory” if it does not include
within the scope of its coverage, prohibits the exercise
of, or is conditioned on the nonexercise of one or more of
the rights that are specifically granted under this License.
You may not convey a covered work if you are a party to
an arrangement with a third party that is in the business of
distributing software, under which you make payment to the
third party based on the extent of your activity of conveying
the work, and under which the third party grants, to any of
the parties who would receive the covered work from you,
a discriminatory patent license (a) in connection with copies
of the covered work conveyed by you (or copies made from
those copies), or (b) primarily for and in connection with
specific products or compilations that contain the covered
work, unless you entered into that arrangement, or that
patent license was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or
limiting any implied license or other defenses to infringement
that may otherwise be available to you under applicable
patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order,
agreement or otherwise) that contradict the conditions of
this License, they do not excuse you from the conditions of
this License. If you cannot convey a covered work so as to
satisfy simultaneously your obligations under this License
and any other pertinent obligations, then as a consequence
you may not convey it at all. For example, if you agree
to terms that obligate you to collect a royalty for further
conveying from those to whom you convey the Program, the
only way you could satisfy both those terms and this License
would be to refrain entirely from conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you
have permission to link or combine any covered work with
a work licensed under version 3 of the GNU Affero General
Public License into a single combined work, and to convey
the resulting work. The terms of this License will continue to
apply to the part which is the covered work, but the special
requirements of the GNU Affero General Public License,
section 13, concerning interaction through a network will
apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/
or new versions of the GNU General Public License from
time to time. Such new versions will be similar in spirit to
the present version, but may differ in detail to address new
problems or concerns.
Each version is given a distinguishing version number. If the
Program specifies that a certain numbered version of the
GNU General Public License “or any later version” applies to
it, you have the option of following the terms and conditions
either of that numbered version or of any later version
published by the Free Software Foundation. If the Program
does not specify a version number of the GNU General
Public License, you may choose any version ever published
by the Free Software Foundation.
If the Program specifies that a proxy can decide which future
versions of the GNU General Public License can be used,
that proxy’s public statement of acceptance of a version
permanently authorizes you to choose that version for the
Program.
Later license versions may give you additional or different
permissions.
However, no additional obligations are imposed on any
author or copyright holder as a result of your choosing to
follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW
OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/
OR CONVEYS THE PROGRAM AS PERMITTED ABOVE,
BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR
A FAILURE OF THE PROGRAM TO OPERATE WITH ANY
OTHER PROGRAMS), EVEN IF SUCH HOLDEROR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided
above cannot be given local legal effect according to their
terms, reviewing courts shall apply local law that most
closely approximates an absolute waiver of all civil liability
in connection with the Program, unless a warranty or
assumption of liability accompanies a copy of the Program
in return for a fee.
END OF TERMS AND CONDITIONS
GNU Lesser General Public License (LGPL 2.1)
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim copies
of this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also
counts as the successor of the GNU Library Public License,
version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your
freedom to share and change free software--to make sure
the software is free for all its users.
This license, the Lesser General Public License, applies to
some specially designated software packages--typically
libraries--of the Free Software Foundation and other authors
who decide to use it. You can use it too, but we suggest you
first think carefully about whether this license or the ordinary
General Public License is the better strategy to use in any
particular case, based on the explanations below.
When we speak of free software, we are referring to freedom
of use, not price. Our General Public Licenses are designed
to make sure that you have the freedom to distribute copies
of free software (and charge for this service if you wish); that
you receive source code or can get it if you want it; that
you can change the software and use pieces of it in new
free programs; and that you are informed that you can do
these things.
To protect your rights, we need to make restrictions that
forbid distributors to deny you these rights or to ask you to
surrender these rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the library
or if you modify it.
For example, if you distribute copies of the library, whether
gratis or for a fee, you must give the recipients all the rights
that we gave you. You must make sure that they, too,
receive or can get the source code. If you link other code
with the library, you must provide complete object files to the
recipients, so that they can relink them with the library after
making changes to the library and recompiling it. And you
must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we
copyright the library, and (2) we offer you this license, which
gives you legal permission to copy, distribute and/or modify
the library.
To protect each distributor, we want to make it very clear
that there is no warranty for the free library. Also, if the library
is modified by someone else and passed on, the recipients
should know that what they have is not the original version,
so that the original author’s reputation will not be affected by
problems that might be introduced by others.
Finally, software patents pose a constant threat to the
existence of any free program. We wish to make sure that
a company cannot effectively restrict the users of a free
program by obtaining a restrictive license from a patent
holder. Therefore, we insist that any patent license obtained
for a version of the library must be consistent with the full
freedom of use specified in this license.
Most GNU software, including some libraries, is covered
by the ordinary GNU General Public License. This license,
the GNU Lesser General Public License, applies to certain
designated libraries, and is quite different from the ordinary
General Public License. We use this license for certain
libraries in order to permit linking those libraries into non-free
programs.
When a program is linked with a library, whether statically or
using a shared library, the combination of the two is legally
speaking a combined work, a derivative of the original
library. The ordinary General Public License therefore permits
such linking only if the entire combination fits its criteria of
freedom. The Lesser General Public License permits more
lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License
because it does Less to protect the user’s freedom than the
ordinary General Public License. It also provides other free
software developers Less of an advantage over competing
non-free programs. These disadvantages are the reason we
use the ordinary General Public License for many libraries.
However, the Lesser license provides advantages in certain
special circumstances.
For example, on rare occasions, there may be a special
need to encourage the widest possible use of a certain
library, so that it becomes a de-facto standard. To achieve
this, non-free programs must be allowed to use the library.
A more frequent case is that a free library does the same job
as widely used non-free libraries. In this case, there is little
to gain by limiting the free library to free software only, so we
use the Lesser General Public License.
In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use a
large body of free software. For example, permission to use
the GNU C Library in non-free programs enables many more
people to use the whole GNU operating system, as well as
its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less
protective of the users’ freedom, it does ensure that the user
of a program that is linked with the Library has the freedom
and the wherewithal to run that program using a modified
version of the Library.
The precise terms and conditions for copying, distribution
and modification follow. Pay close attention to the difference
between a “work based on the library” and a “work that
uses the library”. The former contains code derived from the
library, whereas the latter must be combined with the library
in order to run.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library
or other program which contains a notice placed by the
copyright holder or other authorized party saying it may
be distributed under the terms of this Lesser General
Public License (also called “this License”). Each licensee is
addressed as “you”.
A “library” means a collection of software functions and/
or data prepared so as to be conveniently linked with
application programs (which use some of those functions
and data) to form executables.
The “Library”, below, refers to any such software library
or work which has been distributed under these terms. A
“work based on the Library” means either the Library or any
derivative work under copyright law: that is to say, a work
containing the Library or a portion of it, either verbatim or
with modifications and/or translated straightforwardly into
another language. (Hereinafter, translation is included without
limitation in the term “modification”.)
“Source code” for a work means the preferred form of the
work for making modifications to it. For a library, complete
source code means all the source code for all modules it
contains, plus any associated interface definition files, plus
the scripts used to control compilation and installation of
the library.
Activities other than copying, distribution and modification
are not covered by this License; they are outside its scope.
The act of running a program using the Library is not
restricted, and output from such a program is covered
only if its contents constitute a work based on the Library
(independent of the use of the Library in a tool for writing it).
Whether that is true depends on what the Library does and
what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the
Library’s complete source code as you receive it, in any
medium, provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice and
disclaimer of warranty; keep intact all the notices that refer
to this License and to the absence of any warranty; and
distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies of the Library or any
portion of it, thus forming a work based on the Library, and
copy and distribute such modifications or work under the
terms of Section 1 above, provided that you also meet all of
these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent
notices stating that you changed the files and the date
of any change.
c) You must cause the whole of the work to be licensed
at no charge to all third parties under the terms of
this License.
d) If a facility in the modified Library refers to a function
or a table of data to be supplied by an application
program that uses the facility, other than as an
argument passed when the facility is invoked, then you
must make a good faith effort to ensure that, in the
event an application does not supply such function or
table, the facility still operates, and performs whatever
part of its purpose remains meaningful.
(For example, a function in a library to compute square roots
has a purpose that is entirely well-defined independent of
the application. Therefore, Subsection 2d requires that any
application-supplied function or table used by this function
must be optional: if the application does not supply it, the
square root function must still compute square roots.)
These requirements apply to the modified work as a whole.
If identifiable sections of that work are not derived from the
Library, and can be reasonably considered independent and
separate works in themselves, then this License, and its
terms, do not apply to those sections when you distribute
them as separate works. But when you distribute the same
sections as part of a whole which is a work based on the
Library, the distribution of the whole must be on the terms
of this License, whose permissions for other licensees
extend to the entire whole, and thus to each and every part
regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or
contest your rights to work written entirely by you; rather,
the intent is to exercise the right to control the distribution of
derivative or collective works based on the Library.
In addition, mere aggregation of another work not based
on the Library with the Library (or with a work based on the
Library) on a volume of a storage or distribution medium
does not bring the other work under the scope of this
License.
3. You may opt to apply the terms of the ordinary GNU
General Public License instead of this License to a given
copy of the Library. To do this, you must alter all the notices
that refer to this License, so that they refer to the ordinary
GNU General Public License, version 2, instead of to this
License. (If a newer version than version 2 of the ordinary
GNU General Public License has appeared, then you can
specify that version instead if you wish.) Do not make any
other change in these notices.
Once this change is made in a given copy, it is irreversible
for that copy, so the ordinary GNU General Public License
applies to all subsequent copies and derivative works made
from that copy.
This option is useful when you wish to copy part of the code
of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or
derivative of it, under Section 2) in object code or executable
form under the terms of Sections 1 and 2 above provided
that you accompany it with the complete corresponding
machine-readable source code, which must be distributed
under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange.
If distribution of object code is made by offering access
to copy from a designated place, then offering equivalent
access to copy the source code from the same place
satisfies the requirement to distribute the source code, even
though third parties are not compelled to copy the source
along with the object code.
5. A program that contains no derivative of any portion
of the Library, but is designed to work with the Library by
being compiled or linked with it, is called a “work that uses
the Library”. Such a work, in isolation, is not a derivative
work of the Library, and therefore falls outside the scope of
this License.
However, linking a “work that uses the Library” with the
Library creates an executable that is a derivative of the
Library (because it contains portions of the Library), rather
than a “work that uses the library”. The executable is
therefore covered by this License. Section 6 states terms for
distribution of such executables.
When a “work that uses the Library” uses material from a
header file that is part of the Library, the object code for the
work may be a derivative work of the Library even though
the source code is not. Whether this is true is especially
significant if the work can be linked without the Library, or if
the work is itself a library. The threshold for this to be true is
not precisely defined by law.
If such an object file uses only numerical parameters, data
structure layouts and accessors, and small macros and small
inline functions (ten lines or less in length), then the use of the
object file is unrestricted, regardless of whether it is legally
a derivative work. (Executables containing this object code
plus portions of the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may
distribute the object code for the work under the terms of
Section 6. Any executables containing that work also fall
under Section 6, whether or not they are linked directly with
the Library itself.
6. As an exception to the Sections above, you may also
combine or link a “work that uses the Library” with the
Library to produce a work containing portions of the Library,
and distribute that work under terms of your choice,
provided that the terms permit modification of the work
for the customer’s own use and reverse engineering for
debugging such modifications.
You must give prominent notice with each copy of the work
that the Library is used in it and that the Library and its use
are covered by this License. You must supply a copy of this
License. If the work during execution displays copyright
notices, you must include the copyright notice for the Library
among them, as well as a reference directing the user to the
copy of this License. Also, you must do one of these things:
a) Accompany the work with the complete corresponding
machine-readable source code for the Library including
whatever changes were used in the work (which must
be distributed under Sections 1 and 2 above); and,
if the work is an executable linked with the Library,
with the complete machine-readable “work that uses
the Library”, as object code and/or source code, so
that the user can modify the Library and then relink to
produce a modified executable containing the modified
Library. (It is understood that the user who changes
the contents of definitions files in the Library will not
necessarily be able to recompile the application to use
the modified definitions.)
b) Use a suitable shared library mechanism for linking
with the Library. A suitable mechanism is one that (1)
uses at run time a copy of the library already present
on the user’s computer system, rather than copying
library functions into the executable, and (2) will
operate properly with a modified version of the library,
if the user installs one, as long as the modified version
is interface-compatible with the version that the work
was made with.
c) Accompany the work with a written offer, valid for at
least three years, to give the same user the materials
specified in Subsection 6a, above, for a charge no
more than the cost of performing this distribution.
d) If distribution of the work is made by offering access
to copy from a designated place, offer equivalent
access to copy the above specified materials from
the same place.
e) Verify that the user has already received a copy of
these materials or that you have already sent this
user a copy.
For an executable, the required form of the “work that uses
the Library” must include any data and utility programs
needed for reproducing the executable from it. However,
as a special exception, the materials to be distributed need
not include anything that is normally distributed (in either
source or binary form) with the major components (compiler,
kernel, and so on) of the operating system on which the
executable runs, unless that component itself accompanies
the executable.
It may happen that this requirement contradicts the license
restrictions of other proprietary libraries that do not normally
accompany the operating system. Such a contradiction
means you cannot use both them and the Library together in
an executable that you distribute.
7. You may place library facilities that are a work based on
the Library side-by-side in a single library together with other
library facilities not covered by this License, and distribute
such a combined library, provided that the separate
distribution of the work based on the Library and of the other
library facilities is otherwise permitted, and provided that you
do these two things:
a) Accompany the combined library with a copy of the same
work based on the Library, uncombined with any other
library facilities. This must be distributed under the terms of
the Sections above.
b) Give prominent notice with the combined library of the fact
that part of it is a work based on the Library, and explaining
where to find the accompanying uncombined form of the
same work.
8. You may not copy, modify, sublicense, link with, or
distribute the Library except as expressly provided under
this License. Any attempt otherwise to copy, modify,
sublicense, link with, or distribute the Library is void, and
will automatically terminate your rights under this License.
However, parties who have received copies, or rights, from
you under this License will not have their licenses terminated
so long as such parties remain in full compliance.
9. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Library or its derivative
works. These actions are prohibited by law if you do not
accept this License. Therefore, by modifying or distributing
the Library (or any work based on the Library), you indicate
your acceptance of this License to do so, and all its terms
and conditions for copying, distributing or modifying the
Library or works based on it.
10. Each time you redistribute the Library (or any work
based on the Library), the recipient automatically receives a
license from the original licensor to copy, distribute, link with
or modify the Library subject to these terms and conditions.
You may not impose any further restrictions on the recipients’
exercise of the rights granted herein. You are not responsible
for enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not limited
to patent issues), conditions are imposed on you (whether
by court order, agreement or otherwise) that contradict the
conditions of this License, they do not excuse you from the
conditions of this License. If you cannot distribute so as to
satisfy simultaneously your obligations under this License
and any other pertinent obligations, then as a consequence
you may not distribute the Library at all. For example, if a
patent license would not permit royalty-free redistribution
of the Library by all those who receive copies directly or
indirectly through you, then the only way you could satisfy
both it and this License would be to refrain entirely from
distribution of the Library.
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply, and the section as a whole is intended
to apply in other circumstances.
It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose
of protecting the integrity of the free software distribution
system which is implemented by public license practices.
Many people have made generous contributions to the
wide range of software distributed through that system in
reliance on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to distribute
software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places the
Library under this License may add an explicit geographical
distribution limitation excluding those countries, so that
distribution is permitted only in or among countries not
thus excluded. In such case, this License incorporates the
limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/
or new versions of the Lesser General Public License from
time to time. Such new versions will be similar in spirit to
the present version, but may differ in detail to address new
problems or concerns.
Each version is given a distinguishing version number. If the
Library specifies a version number of this License which
applies to it and “any later version”, you have the option of
following the terms and conditions either of that version or of
any later version published by the Free Software Foundation.
If the Library does not specify a license version number, you
may choose any version ever published by the Free Software
Foundation.
14. If you wish to incorporate parts of the Library into other
free programs whose distribution conditions are incompatible
with these, write to the author to ask for permission.
For software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be
guided by the two goals of preserving the free status of all
derivatives of our free software and of promoting the sharing
and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY,
TO THE EXTENT PERMITTED BY APPLICABLE LAW.
EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF
ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD
THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE
COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY
AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE THE LIBRARY (INCLUDING
BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY
TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New
Libraries
If you develop a new library, and you want it to be of the
greatest possible use to the public, we recommend making
it free software that everyone can redistribute and change.
You can do so by permitting redistribution under these terms
(or, alternatively, under the terms of the ordinary General
Public License).
To apply these terms, attach the following notices to the
library. It is safest to attach them to the start of each source
file to most effectively convey the exclusion of warranty;
and each file should have at least the “copyright” line and a
pointer to where the full notice is found.
Mozilla Public License
Since we, at Samsung Techwin, used the Mozilla Firefox component without modifying the source code according to the
MOZILLA Public license 1.1, we are not obliged to provide the source code of the corresponding component.
 Version 1.1
Definitions.
1.11. “Source Code”
1.0.1. “Commercial Use”
means the preferred form of the Covered Code for making
modifications to it, including all modules it contains, plus
any associated interface definition files, scripts used to
control compilation and installation of an Executable, or
source code differential comparisons against either the
Original Code or another well known, available Covered
Code of the Contributor’s choice. The Source Code can be
in a compressed or archival form, provided the appropriate
decompression or de-archiving software is widely available
for no charge.
means distribution or otherwise making the Covered Code
available to a third party.
1.1. “Contributor”
means each entity that creates or contributes to the creation
of Modifications.
1.2. “Contributor Version”
means the combination of the Original Code, prior
Modifications used by a Contributor, and the Modifications
made by that particular Contributor.
1.12. “You” (or “Your”)
means a mechanism generally accepted in the software
development community for the electronic transfer of data.
means an individual or a legal entity exercising rights under,
and complying with all of the terms of, this License or a
future version of this License issued under Section 6.1. For
legal entities, “You” includes any entity which controls, is
controlled by, or is under common control with You. For
purposes of this definition, “control” means (a) the power,
direct or indirect, to cause the direction or management
of such entity, whether by contract or otherwise, or (b)
ownership of more than fifty percent (50%) of the outstanding
shares or beneficial ownership of such entity.
1.5. “Executable”
2. Source Code License.
means Covered Code in any form other than Source Code.
2.1. The Initial Developer Grant.
1.6. “Initial Developer”
The Initial Developer hereby grants You a world-wide, royaltyfree, non-exclusive license, subject to third party intellectual
property claims:
1.3. “Covered Code”
means the Original Code or Modifications or the combination
of the Original Code and Modifications, in each case
including portions thereof.
1.4. “Electronic Distribution Mechanism”
means the individual or entity identified as the Initial
Developer in the Source Code notice required by Exhibit A.
1.7. “Larger Work”
means a work which combines Covered Code or portions
thereof with code not governed by the terms of this License.
1.8. “License”
means this document.
1.8.1. “Licensable”
means having the right to grant, to the maximum extent
possible, whether at the time of the initial grant or
subsequently acquired, any and all of the rights conveyed
herein.
1.9. “Modifications”
means any addition to or deletion from the substance
or structure of either the Original Code or any previous
Modifications. When Covered Code is released as a series of
files, a Modification is:
a. Any addition to or deletion from the contents of a file
containing Original Code or previous Modifications.
b. Any new file that contains any part of the Original Code
or previous Modifications.
1.10. “Original Code”
means Source Code of computer software code which is
described in the Source Code notice required by Exhibit
A as Original Code, and which, at the time of its release
under this License is not already Covered Code governed
by this License.
1.10.1. “Patent Claims”
means any patent claim(s), now owned or hereafter acquired,
including without limitation, method, process, and apparatus
claims, in any patent Licensable by grantor.
a. under intellectual property rights (other than patent
or trademark) Licensable by Initial Developer to use,
reproduce, modify, display, perform, sublicense and
distribute the Original Code (or portions thereof) with
or without Modifications, and/or as part of a Larger
Work; and
b. under Patents Claims infringed by the making, using
or selling of Original Code, to make, have made, use,
practice, sell, and offer for sale, and/or otherwise
dispose of the Original Code (or portions thereof).
c. the licenses granted in this Section 2.1 (a) and (b) are
effective on the date Initial Developer first distributes
Original Code under the terms of this License.
d. Notwithstanding Section 2.1 (b) above, no patent
license is granted: 1) for code that You delete from the
Original Code; 2) separate from the Original Code; or
3) for infringements caused by: i) the modification of
the Original Code or ii) the combination of the Original
Code with other software or devices.
2.2. Contributor Grant.
Subject to third party intellectual property claims, each
Contributor hereby grants You a world-wide, royalty-free,
non-exclusive license
a. under intellectual property rights (other than patent
or trademark) Licensable by Contributor, to use,
reproduce, modify, display, perform, sublicense
and distribute the Modifications created by such
Contributor (or portions thereof) either on an
unmodified basis, with other Modifications, as Covered
Code and/or as part of a Larger Work; and
b. under Patent Claims infringed by the making, using,
or selling of Modifications made by that Contributor
either alone and/or in combination with its Contributor
Version (or portions of such combination), to make,
use, sell, offer for sale, have made, and/or otherwise
dispose of: 1) Modifications made by that Contributor
(or portions thereof); and 2) the combination of
Modifications made by that Contributor with its
Contributor Version (or portions of such combination).
c. the licenses granted in Sections 2.2 (a) and 2.2 (b)
are effective on the date Contributor first makes
Commercial Use of the Covered Code.
d. Notwithstanding Section 2.2 (b) above, no patent
license is granted: 1) for any code that Contributor
has deleted from the Contributor Version; 2) separate
from the Contributor Version; 3) for infringements
caused by: i) third party modifications of Contributor
Version or ii) the combination of Modifications made
by that Contributor with other software (except as
part of the Contributor Version) or other devices; or
4) under Patent Claims infringed by Covered Code in
the absence of Modifications made by that Contributor.
3. Distribution Obligations.
3.1. Application of License.
The Modifications which You create or to which You
contribute are governed by the terms of this License,
including without limitation Section 2.2. The Source Code
version of Covered Code may be distributed only under
the terms of this License or a future version of this License
released under Section6.1, and You must include a copy
of this License with every copy of the Source Code You
distribute. You may not offer or impose any terms on any
Source Code version that alters or restricts the applicable
version of this License or the recipients’ rights hereunder.
However, You may include an additional document offering
the additional rights described in Section 3.5.
3.2. Availability of Source Code.
Any Modification which You create or to which You
contribute must be made available in Source Code form
under the terms of this License either on the same media
as an Executable version or via an accepted Electronic
Distribution Mechanism to anyone to whom you made
an Executable version available; and if made available via
Electronic Distribution Mechanism, must remain available for
at least twelve (12) months after the date it initially became
available, or at least six (6) months after a subsequent
version of that particular Modification has been made
available to such recipients. You are responsible for ensuring
that the Source Code version remains available even if
the Electronic Distribution Mechanism is maintained by a
third party.
3.3. Description of Modifications.
You must cause all Covered Code to which You contribute
to contain a file documenting the changes You made to
create that Covered Code and the date of any change. You
must include a prominent statement that the Modification
is derived, directly or indirectly, from Original Code provided
by the Initial Developer and including the name of the Initial
Developer in (a) the Source Code, and (b) in any notice in an
Executable version or related documentation in which You
describe the origin or ownership of the Covered Code.
3.4. Intellectual Property Matters
(a) Third Party Claims
If Contributor has knowledge that a license under a third
party’s intellectual property rights is required to exercise
the rights granted by such Contributor under Sections 2.1
or 2.2, Contributor must include a text file with the Source
Code distribution titled “LEGAL” which describes the claim
and the party making the claim in sufficient detail that a
recipient will know whom to contact. If Contributor obtains
such knowledge after the Modification is made available
as described in Section 3.2, Contributor shall promptly
modify the LEGAL file in all copies Contributor makes
available thereafter and shall take other steps (such as
notifying appropriate mailing lists or newsgroups) reasonably
calculated to inform those who received the Covered Code
that new knowledge has been obtained.
(b) Contributor APIs
If Contributor’s Modifications include an application
programming interface and Contributor has knowledge
of patent licenses which are reasonably necessary to
implement that API, Contributor must also include this
information in the LEGAL file.
(c) Representations.
Contributor represents that, except as disclosed pursuant to
Section 3.4 (a) above, Contributor believes that Contributor’s
Modifications are Contributor’s original creation(s) and/or
Contributor has sufficient rights to grant the rights conveyed
by this License.
3.5. Required Notices.
You must duplicate the notice in Exhibit A in each file of
the Source Code. If it is not possible to put such notice in
a particular Source Code file due to its structure, then You
must include such notice in a location (such as a relevant
directory) where a user would be likely to look for such a
notice. If You created one or more Modification(s) You may
add your name as a Contributor to the notice described
in Exhibit A. You must also duplicate this License in any
documentation for the Source Code where You describe
recipients’ rights or ownership rights relating to Covered
Code. You may choose to offer, and to charge a fee for,
warranty, support, indemnity or liability obligations to one
or more recipients of Covered Code. However, You may do
so only on Your own behalf, and not on behalf of the Initial
Developer or any Contributor. You must make it absolutely
clear than any such warranty, support, indemnity or liability
obligation is offered by You alone, and You hereby agree to
indemnify the Initial Developer and every Contributor for any
liability incurred by the Initial Developer or such Contributor
as a result of warranty, support, indemnity or liability terms
You offer.
3.6. Distribution of Executable Versions.
You may distribute Covered Code in Executable form only
if the requirements of Sections 3.1, 3.2, 3.3, 3.4 and 3.5
have been met for that Covered Code, and if You include a
notice stating that the Source Code version of the Covered
Code is available under the terms of this License, including
a description of how and where You have fulfilled the
obligations of Section 3.2. The notice must be conspicuously
included in any notice in an Executable version, related
documentation or collateral in which You describe recipients’
rights relating to the Covered Code. You may distribute
the Executable version of Covered Code or ownership
rights under a license of Your choice, which may contain
terms different from this License, provided that You are
in compliance with the terms of this License and that the
license for the Executable version does not attempt to limit
or alter the recipient’s rights in the Source Code version
from the rights set forth in this License. If You distribute
the Executable version under a different license You must
make it absolutely clear that any terms which differ from this
License are offered by You alone, not by the Initial Developer
or any Contributor. You hereby agree to indemnify the Initial
Developer and every Contributor for any liability incurred by
the Initial Developer or such Contributor as a result of any
such terms You offer.
3.7. Larger Works.
8. Termination
You may create a Larger Work by combining Covered Code
with other code not governed by the terms of this License
and distribute the Larger Work as a single product. In such a
case, You must make sure the requirements of this License
are fulfilled for the Covered Code.
8.1. This License and the rights granted hereunder will
terminate automatically if You fail to comply with terms herein
and fail to cure such breach within 30 days of becoming
aware of the breach. All sublicenses to the Covered Code
which are properly granted shall survive any termination of
this License. Provisions which, by their nature, must remain
in effect beyond the termination of this License shall survive.
4. Inability to Comply Due to Statute or Regulation.
If it is impossible for You to comply with any of the terms of
this License with respect to some or all of the Covered Code
due to statute, judicial order, or regulation then You must:
(a) comply with the terms of this License to the maximum
extent possible; and (b) describe the limitations and the code
they affect. Such description must be included in the LEGAL
file described in Section 3.4 and must be included with
all distributions of the Source Code. Except to the extent
prohibited by statute or regulation, such description must be
sufficiently detailed for a recipient of ordinary skill to be able
to understand it.
5. Application of this License.
This License applies to code to which the Initial Developer
has attached the notice in Exhibit A and to related Covered
Code.
6. Versions of the License.
6.1. New Versions
Netscape Communications Corporation (“Netscape”) may
publish revised and/or new versions of the License from
time to time. Each version will be given a distinguishing
version number.
6.2. Effect of New Versions
Once Covered Code has been published under a particular
version of the License, You may always continue to use it
under the terms of that version. You may also choose to
use such Covered Code under the terms of any subsequent
version of the License published by Netscape. No one other
than Netscape has the right to modify the terms applicable
to Covered Code created under this License.
6.3. Derivative Works
If You create or use a modified version of this License
(which you may only do in order to apply it to code which is
not already Covered Code governed by this License), You
must (a) rename Your license so that the phrases “Mozilla”,
“MOZILLAPL”, “MOZPL”, “Netscape”, “MPL”, “NPL” or any
confusingly similar phrase do not appear in your license
(except to note that your license differs from this License)
and (b) otherwise make it clear that Your version of the
license contains terms which differ from the Mozilla Public
License and Netscape Public License. (Filling in the name
of the Initial Developer, Original Code or Contributor in the
notice described in Exhibit A shall not of themselves be
deemed to be modifications of this License.)
7. DISCLAIMER OF WARRANTY
COVERED CODE IS PROVIDED UNDER THIS LICENSE
ON AN “AS IS” BASIS, WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
WITHOUT LIMITATION, WARRANTIES THAT THE COVERED
CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR
A PARTICULAR PURPOSE OR NON-INFRINGING. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE
OF THE COVERED CODE IS WITH YOU. SHOULD ANY
COVERED CODE PROVE DEFECTIVE IN ANY RESPECT,
YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER
CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY
SERVICING, REPAIR OR CORRECTION. THIS DISCLAIMER
OF WARRANTY CONSTITUTES AN ESSENTIAL PART
OF THIS LICENSE. NO USE OF ANY COVERED CODE
IS AUTHORIZED HEREUNDER EXCEPT UNDER THIS
DISCLAIMER.
8.2. If You initiate litigation by asserting a patent infringement
claim (excluding declatory judgment actions) against
Initial Developer or a Contributor (the Initial Developer or
Contributor against whom You file such action is referred to
as “Participant”) alleging that:
a. such Participant’s Contributor Version directly or
indirectly infringes any patent, then any and all rights
granted by such Participant to You under Sections
2.1 and/or 2.2 of this License shall, upon 60 days
notice from Participant terminate prospectively, unless
if within 60 days after receipt of notice You either: (i)
agree in writing to pay Participant a mutually agreeable
reasonable royalty for Your past and future use of
Modifications made by such Participant, or (ii) withdraw
Your litigation claim with respect to the Contributor
Version against such Participant. If within 60 days of
notice, a reasonable royalty and payment arrangement
are not mutually agreed upon in writing by the parties
or the litigation claim is not withdrawn, the rights
granted by Participant to You under Sections 2.1 and/
or 2.2 automatically terminate at the expiration of the
60 day notice period specified above.
b. any software, hardware, or device, other than such
Participant’s Contributor Version, directly or indirectly
infringes any patent, then any rights granted to You by
such Participant under Sections 2.1(b) and 2.2(b) are
revoked effective as of the date You first made, used,
sold, distributed, or had made, Modifications made by
that Participant.
8.3. If You assert a patent infringement claim against
Participant alleging that such Participant’s Contributor
Version directly or indirectly infringes any patent where such
claim is resolved (such as by license or settlement) prior
to the initiation of patent infringement litigation, then the
reasonable value of the licenses granted by such Participant
under Sections 2.1 or 2.2 shall be taken into account in
determining the amount or value of any payment or license.
8.4. In the event of termination under Sections 8.1 or
8.2 above, all end user license agreements (excluding
distributors and resellers) which have been validly granted
by You or any distributor hereunder prior to termination shall
survive termination.
9. LIMITATION OF LIABILITY
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL
THEORY, WHETHER TORT (INCLUDING NEGLIGENCE),
CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL
DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY
DISTRIBUTOR OF COVERED CODE, OR ANY SUPPLIER
OF ANY OF SUCH PARTIES, BE LIABLE TO ANY
PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER
INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER
FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER
COMMERCIAL DAMAGES OR LOSSES, EVEN IF
SUCH PARTY SHALL HAVE BEEN INFORMED OF THE
POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF
LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH
OR PERSONAL INJURY RESULTING FROM SUCH PARTY’S
NEGLIGENCE TO THE EXTENT APPLICABLE LAW
PROHIBITS SUCH LIMITATION. SOME JURISDICTIONS
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS
EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU.
10. U.S. government end users
The Covered Code is a “commercial item,” as that term
is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of
“commercial computer software” and “commercial computer
software documentation,” as such terms are used in 48
C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R.
12.212 and 48 C.F.R.227.7202-1 through 227.7202-4 (June
1995), all U.S. Government End Users acquire Covered
Code with only those rights set forth herein.
11. Miscellaneous
This License represents the complete agreement concerning
subject matter hereof. If any provision of this License is held
to be unenforceable, such provision shall be reformed only
to the extent necessary to make it enforceable. This License
shall be governed by California law provisions (except to the
extent applicable law, if any, provides otherwise), excluding
its conflict-of-law provisions. With respect to disputes in
which at least one party is a citizen of, or an entity chartered
or registered to do business in the United States of America,
any litigation relating to this License shall be subject to the
jurisdiction of the Federal Courts of the Northern District of
California, with venue lying in Santa Clara County, California,
with the losing party responsible for costs, including without
limitation, court costs and reasonable attorneys’ fees and
expenses. The application of the United Nations Convention
on Contracts for the International Sale of Goods is expressly
excluded. Any law or regulation which provides that the
language of a contract shall be construed against the drafter
shall not apply to this License.
12. Responsibility for claims
As between Initial Developer and the Contributors, each
party is responsible for claims and damages arising,
directly or indirectly, out of its utilization of rights under this
License and You agree to work with Initial Developer and
Contributors to distribute such responsibility on an equitable
basis. Nothing herein is intended or shall be deemed to
constitute any admission of liability.
13. Multiple-licensed code
Initial Developer may designate portions of the Covered
Code as “Multiple-Licensed”. “Multiple-Licensed” means
that the Initial Developer permits you to utilize portions of
the Covered Code under Your choice of the MPL or the
alternative licenses, if any, specified by the Initial Developer in
the file described inExhibit A.
Exhibit A - Mozilla Public License.
“The contents of this file are subject to the Mozilla Public
License Version 1.1 (the “License”); you may not use this file
except in compliance with the License. You may obtain a
copy of the License at http://www.mozilla.org/MPL/
Software distributed under the License is distributed on an
“AS IS” basis, WITHOUT WARRANTY OF ANY KIND, either
express or implied. See the License for the specific language
governing rights and limitations under the License.
The Original Code is _________________________________.
The Initial Developer of the Original Code is
________________________.
Portions created by ______________________ are Copyright
(C) _____________________________. All Rights Reserved.
Contributor(s): ______________________________________.
Alternatively, the contents of this file may be used under the
terms of the _____ license (the “[___] License”), in which
case the
provisions of [______] License are applicable instead of those
above. If you wish to allow use of your version of this file only
under the terms of the [____] License and not to allow others
to use your version of this file under the MPL, indicate your
decision by deleting the provisions above and replace them
with the notice and other provisions required by the [___]
License. If you do not delete the provisions above, a recipient
may use your version of this file under either the MPL or the
[___] License.”
NOTE: The text of this Exhibit A may differ slightly from the
text of the notices in the Source Code files of the Original
Code. You should use the text of this Exhibit A rather than
the text found in the Original Code Source Code for Your
Modifications.
BSD License
Some software components of this product incorporate source code covered under the BSD license as follows.
Component Name
License
URL
lighttpd-1.4.31
BSD 2.0
http://www.lighttpd.net/assets/COPYING
ppp-2.4.2
BSD 2.0
http://ppp.samba.org/
net-snmp-5.4.1
BSD 2.0
http://www.net-snmp.org/about/license.html
game-ws
BSD 2.0
https://code.google.com/p/game-ws/
MiniUPnP Project Client
BSD 2.0
http://miniupnp.tuxfamily.org/
lighttpd is a secure, fast, compliant, and very flexible
webserver that has been optimized for high-performance
environments. It has a very low memory footprint compared
to other webservers and takes care of cpuload. Its advanced
feature-set (FastCGI, CGI, Auth, Output-Compression,
URL-Rewriting and many more) make lighttpd the perfect
webserver-software for every server that suffers load
problems. Simple Network Management Protocol (SNMP)
is an Internetstandard protocol for managing devices on IP
networks. It is used mostly in network management systems
to monitor the devices attached to the network for conditions
that need administrative attention. Net-SNMP is a suite of
applications used to implement SNMP v1, SNMP v2c and
SNMP v3 using both IPv4 and IPv6. For more additional
information, send email to help.cctv@samsung.com.
Copyright (c) 2004, Kneschke, incremental
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
- Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
Component Name
URL
ppp-2.4.2
http://ppp.samba.org/
Copyright (c) 1994-2003 Paul Mackerras.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. The name(s) of the authors of this software must not be
used to endorse or promote products derived from this
software without prior written permission.
4. Redistributions of any form whatsoever must retain the
following acknowledgment:
“This product includes software developed by Paul
Mackerras <paulus@samba.org>”.
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL
WARRANTIES WITH REGARD TO THIS SOFTWARE,
INCLUDING ALL IMPLIED WARRANTIES OF
- Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
- Neither the name of the ‘incremental’ nor the names of
its contributors may be used to endorse or promote
products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL
THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT
OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
WHATSOEVER RESULTING FROM LOSS OF USE, DATA
OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING
OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Copyright (c) 1995 Eric Rosenquist.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. The name(s) of the authors of this software must not be
used to endorse or promote products derived from this
software without prior written permission.
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL
WARRANTIES WITH REGARD TO THIS SOFTWARE,
INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL
THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT
OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
WHATSOEVER RESULTING FROM LOSS OF USE, DATA
OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING
OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Copyright (c) 1984-2000 Carnegie Mellon University.
All rights reserved.
Redistribution and use in source and binary forms are
permitted provided that the above copyright notice and
this paragraph are duplicated in all such forms and that any
documentation,
advertising materials, and other materials related to such
distribution and use acknowledge that the software was
eveloped by Carnegie Mellon University. The name of the
University may not be used to endorse or promote products
derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED ``AS IS’’ AND WITHOUT
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
MERCHANTIBILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
Copyright (c) 1995 Pedro Roque Marques.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. The names of the authors of this software must not be
used to endorse or promote products derived from this
software without prior written permission.
4. Redistributions of any form whatsoever must retain the
following acknowledgment: “This product includes software
developed by Pedro Roque Marques <pedro_m@yahoo.
com>”
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL
WARRANTIES WITH REGARD TO THIS SOFTWARE,
INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL
THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT
OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
WHATSOEVER RESULTING FROM LOSS OF USE, DATA
OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING
OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Copyright (c) 1999 Tommi Komulainen.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. The name(s) of the authors of this software must not be
used to endorse or promote products derived from this
software without prior written permission.
4. Redistributions of any form whatsoever must retain the
following acknowledgment: “This product includes software
developed by Tommi Komulainen <Tommi.Komulainen@
iki.fi>”.
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL
WARRANTIES WITH REGARD TO THIS SOFTWARE,
INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL
THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT
OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
WHATSOEVER RESULTING FROM LOSS OF USE, DATA
OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING
OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Copyright (c) 2001 by Sun Microsystems, Inc.
All rights reserved.
Non-exclusive rights to redistribute, modify, translate, and
use this software in source and binary forms, in whole or in
part, is hereby granted, provided that the above copyright
notice is duplicated in any source form, and that neither
the name of the copyright holder nor the author is used to
endorse or promote products derived from this software.
THIS SOFTWARE IS PROVIDED ``AS IS’’ AND WITHOUT
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
MERCHANTIBILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
Copyright (c) 2002 Google, Inc.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice ,this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. The name(s) of the authors of this software must not be
used to endorse or promote products derived from this
software without prior written permission.
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL
WARRANTIES WITH REGARD TO THIS SOFTWARE,
INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL
THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT
OR
CONSEQUENTIAL DAMAGES OR ANY DAMAGES
WHATSOEVER RESULTING FROM LOSS OF USE, DATA
OR PROFITS, WHETHER IN N ACTION OF CONTRACT,
NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING
OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Component Name
URL
net-snmp-5.4.1
http://www.net-snmp.org/about/license.html
Various copyrights apply to this package, listed in various
separate parts below. Please make sure that you read all
the parts.
---- Part 1: CMU/UCD copyright notice: (BSD like) ----Copyright 1989, 1991, 1992 by Carnegie Mellon
University
Derivative Work - 1996, 1998-2000
Copyright 1996, 1998-2000 The Regents of the
University of California
All Rights Reserved
Permission to use, copy, modify and distribute this software
and its documentation for any purpose and without fee is
hereby granted, provided that the above copyright notice
appears in all copies and that both that copyright notice and
this permission notice appear in supporting documentation,
and that the name of CMU and The Regents of the University
of California not be used in advertising or publicity pertaining
to distribution of the software without specific written
permission.
CMU AND THE REGENTS OF THE UNIVERSITY OF
CALIFORNIA DISCLAIM ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS.
IN NO EVENT SHALL CMU OR THE REGENTS OF THE
UNIVERSITY OF CALIFORNIA BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES
OR ANY DAMAGES WHATSOEVER RESULTING FROM
THE LOSS OF USE, DATA OR PROFITS, WHETHER
IN AN ACTION OF CONTRACT, NEGLIGENCE OR
OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
CONNECTION WITH THE USE OR PERFORMANCE OF
THIS SOFTWARE.
CMU AND THE REGENTS OF THE UNIVERSITY OF
CALIFORNIA DISCLAIM ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS.
IN NO EVENT SHALL CMU OR THE REGENTS OF THE
UNIVERSITY OF CALIFORNIA BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES
OR ANY DAMAGES WHATSOEVER RESULTING FROM
THE LOSS OF USE, DATA OR PROFITS, WHETHER
IN AN ACTION OF CONTRACT, NEGLIGENCE OR
OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
CONNECTION WITH THE USE OR PERFORMANCE OF
THIS SOFTWARE.
---- Part 2: Networks Associates Technology, Inc
copyright notice (BSD) ----Copyright (c) 2001-2003, Networks Associates
Technology, Inc
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
* Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
* Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
* Neither the name of the Networks Associates Technology,
Inc nor the names of its contributors may be used to
endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS ``AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
---- Part 3: Cambridge Broadband Ltd. copyright notice
(BSD) ----Portions of this code are copyright (c) 2001-2003,
Cambridge Broadband Ltd.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
* Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
* Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
* The name of Cambridge Broadband Ltd. may not be used
to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDER ``AS IS’’ AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE
COPYRIGHT HOLDER BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
---- Part 4: Sun Microsystems, Inc. copyright notice
(BSD) ----Copyright © 2003 Sun Microsystems, Inc., 4150 Network
Circle, Santa Clara, California 95054, U.S.A.
All rights reserved.
Use is subject to license terms below.
This distribution may include materials developed by third
parties.
Sun, Sun Microsystems, the Sun logo and Solaris are
trademarks or registered trademarks of Sun Microsystems,
Inc. in the U.S. and other countries.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
* Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
* Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
* Neither the name of the Sun Microsystems, Inc. nor
the names of its contributors may be used to endorse
or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS ``AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
---- Part 5: Sparta, Inc copyright notice (BSD) ----Copyright (c) 2003-2009, Sparta, Inc
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
* Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
* Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
* Neither the name of Sparta, Inc nor the names of its
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS ``AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
---- Part 6: Cisco/BUPTNIC copyright notice (BSD) ----Copyright (c) 2004, Cisco, Inc and Information Network
Center of Beijing University of Posts and
Telecommunications.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
* Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
* Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
* Neither the name of Cisco, Inc, Beijing University of
Posts and Telecommunications, nor the names of their
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS ``AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
---- Part 7: Fabasoft R&D Software GmbH & Co KG
copyright notice (BSD) ----Copyright (c) Fabasoft R&D Software GmbH & Co KG,
2003 oss@fabasoft.com
Author: Bernhard Penz
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
* Redistributions of source code must retain the above
copyright notice,
this list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
* The name of Fabasoft R&D Software GmbH & Co KG or
any of its subsidiaries, brand or product names may not
be used to endorse or promote products derived from this
software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDER ``AS IS’’ AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE
COPYRIGHT HOLDER BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
---- Part 8: Apple Inc. copyright notice (BSD) ----Copyright (c) 2007 Apple Inc.
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
---- Part 9: ScienceLogic, LLC copyright notice (BSD)
----Copyright (c) 2009, ScienceLogic, LLC
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
* Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. Neither the name of Apple Inc. (“Apple”) nor the names
of its contributors may be used to endorse or promote
products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY APPLE AND ITS
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL APPLE OR
ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
* Neither the name of ScienceLogic, LLC nor the names
of its contributors may be used to endorse or promote
products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS ``AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
COPYRIGHT
HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
Component Name
URL
game-ws
https://code.google.com/p/game-ws/
Copyright (c) 2006, Creative Labs Inc
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. Neither the name of the Creative Labs nor the names of its
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Component Name
URL
MiniUPnP Project Client
http://miniupnp.tuxfamily.org/
Copyright (c) 1991, 1993 The Regents of the University
of California.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. Neither the name of the Regents of the University of
California nor the names of its contributors may be used
to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 2005-2012, Thomas BERNARD
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. Neither the name of Thomas BERNARD nor the names
of its contributors may be used to endorse or promote
products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA,OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The MIT License
Some software components of this product incorporate source code covered under the MIT license as follows
MIT License 2.0
libxml2-2.7.6, ncurses-5.7, Gimpact Collision Kernel, Acewidget, bettermeans, jquery-ui, libxml, Mesa3DMesaLib,mwEmbed,OpenGL Samples Pack, Wide Studio, xorg-server,
dropbear- 0.52 (https://matt.ucc.asn.au/dropbear/dropbear.html)
Copyright (c) 2011, The Dojo Foundation
Copyright William Brack <wbrack@mmm.com.hk>
Copyright 2010, AUTHORS.txt (http://jqueryui.com/about)
Copyright (c) 2007-2010 The Khronos Group Inc.
Dual licensed under the MIT or GPL Version 2 licenses.
Copyright Atish Kumar Patra
- http://jquery.org/license
Copyright (c) 1999-2000 Pawel W. Olszta.
- http://docs.jquery.com/UI/Widget
Permission is hereby granted, free of charge, to any
person obtaining a copy of this software and associated
documentation files (the “Software”), to deal in the Software
without restriction, including without limitation the rights to
use, copy, modify, merge, publish, distribute, sublicense,
and/or sell copies of the Software, and to permit persons
to whom the Software is furnished to do so, subject to the
following conditions:
The above copyright notice and this permission notice
shall be included in all copies or substantial portions of the
Software.
Copyright Daniel Veillard
Copyright Igor Zlatovic <igor@zlatkovic.com>
Copyright Aleksey Sanin
Copyright Gary Pennington <Gary.Pennington@uk.sun.com>
Copyright Alfred Mickautsch <alfred@mickautsch.de>
Copyright Bjorn Reese <bjorn.reese@systematic.dk>
Copyright Joel W. Reed
Component Name
License
URL
dropbear-0.52
MIT 2.0
http://www.opensource.org/licenses/mit-license.php
Dropbear contains a number of components from different
sources, hence there are a few licenses and authors
involved. All licenses are fairly non-restrictive.
The majority of code is written by Matt Johnston, under the
license below.
Portions of the client-mode work are (c) 2004 Mihnea
Stoenescu, under the same license:
Copyright (c) 2002-2006 Matt Johnston
Portions copyright (c) 2004 Mihnea Stoenescu
All rights reserved.
Permission is hereby granted, free of charge, to any
person obtaining a copy of this software and associated
documentation files (the “Software”), to deal in the Software
without restriction, including without limitation the rights to
use, copy, modify, merge, publish, distribute, sublicense,
and/or sell copies of the Software, and to permit persons
to whom the Software is furnished to do so, subject to the
following conditions:
The above copyright notice and this permission notice
shall be included in all copies or substantial portions of the
Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT
SHALL THE AUTHORS OR COPYRIGHT HOLDERS
BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
CONNECTION WITH THE SOFTWARE OR THE USE OR
OTHER DEALINGS IN THE SOFTWARE.
=====
LibTomCrypt and LibTomMath are written by Tom St Denis,
and are Public Domain.
=====
sshpty.c is taken from OpenSSH 3.5p1,
Copyright (c) 1995 Tatu Ylonen <ylo@cs.hut.fi>, Espoo,
Finland
All rights reserved
“As far as I am concerned, the code I have written for this
software can be used freely for any purpose. Any derived
versions of this software must be clearly marked as such,
and if the derived work is incompatible with the protocol
description in the RFC file, it must be called by a name other
than “ssh” or “Secure Shell”. “
=====
loginrec.c
loginrec.h
atomicio.h
atomicio.c
and strlcat() (included in util.c) are from OpenSSH 3.6.1p2,
and are licensed under the 2 point BSD license.
loginrec is written primarily by Andre Lucas, atomicio.c by
Theo de Raadt.
strlcat() is (c) Todd C. Miller
=====
Import code in keyimport.c is modified from PuTTY’s
import.c, licensed as follows:
PuTTY is copyright 1997-2003 Simon Tatham.
Portions copyright Robert de Bath, Joris van Rantwijk,
Delian Delchev, Andreas Schultz, Jeroen Massar, Wez
Furlong, Nicolas Barry, Justin Bradford, and CORE
SDI S.A.
Permission is hereby granted, free of charge, to any
person obtaining a copy of this software and associated
documentation files (the “Software”), to deal in the Software
without restriction, including without limitation the rights to
use, copy, modify, merge, publish, distribute, sublicense,
and/or sell copies of the Software, and to permit persons
to whom the Software is furnished to do so, subject to the
following conditions:
The above copyright notice and this permission notice
shall be included in all copies or substantial portions of the
Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT
SHALL THE COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN
AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
OpenSSL Combined LICENSE
openssl-0.9.8e
http://www.openssl.org/
OpenSSL LICENSE
Copyright (c) 1998-2006 The OpenSSL Project. All rights
reserved. Redistribution and use in source and binary forms,
with or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. All advertising materials mentioning features or use of
this software must display the following acknowledgment:
“This product includes software developed by the OpenSSL
Project for use in the OpenSSL
Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project”
must not be used to endorse or promote products derived
from this software without prior written permission. For
written permission, please contact opensslcore@openssl.
org.
5. Products derived from this software may not be called
“OpenSSL” nor may “OpenSSL” appear in their names
without prior written permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the
following acknowledgment: “This product includes software
developed by the OpenSSL Project for use in the OpenSSL
Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL
PROJECT ‘‘AS IS’’ AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE OpenSSL
PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
This product includes cryptographic software written by Eric
Young (eay@cryptsoft.com). This product includes software
written by Tim Hudson (tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com)
All rights reserved. This package is an SSL implementation
written by Eric Young (eay@cryptsoft.com). The
implementation was written so as to conform with Netscapes
SSL. This library is free for commercial and noncommercial
use as long as the following conditions are aheared to.
The following conditions apply to all code found in this
distribution, be it the RC4, RSA, lhash, DES, etc., code; not
just the SSL code. The SSL documentation included with
this distribution is covered by the same copyright terms
except that the holder is Tim Hudson (tjh@cryptsoft. com).
Copyright remains Eric Young’s, and as such any Copyright
notices in the code are not to be removed. If this package
is used in a product, Eric Young should be given attribution
as the author of the parts of the library used. This can be
in the form of a textual message at program startup or in
documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. All advertising materials mentioning features or use of
this software must display the following acknowledgement:
“This product includes cryptographic software written by Eric
Young (eay@cryptsoft.com)” The word ‘cryptographic’ can
be left out if the rouines from the library being used are not
cryptographic related :-).
4. If you include any Windows specific code (or a derivative
thereof) from the apps directory (application code) you
must include an acknowledgement: “This product includes
software written by Tim Hudson (tjh@cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ‘‘AS
IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.The licence
and distribution terms for any publically available version or
derivative of this code cannot be changed. i.e. this code
cannot simply be copied and put under another distribution
licence [including the GNU Public Licence].
bzip2 License
bzip2-1.0.5
http://www.bzip.org/
This program, “bzip2”, the associated library “libbzip2”, and
all documentation, are copyright (C) 1996-2005 Julian R
Seward. All rights reserved.
4. The name of the author may not be used to endorse or
promote products derived from this software without
specific prior written permission.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
THIS SOFTWARE IS PROVIDED BY THE AUTHOR “AS
IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. The origin of this software must not be misrepresented;
you must not claim that you wrote the original software. If
you use this software in a product, an acknowledgment in
the product documentation would be appreciated but is
not required.
3. Altered source versions must be plainly marked as such,
and must not be misrepresented as being the original
software.
The Independent JPEG Group’s JPEG Software
The software included in this product contains copyrighted software that is licensed under the JPEG license.
 JPEG license
- Code project – Generating Outline OpenGL, libjpeg
This distribution contains the sixth public release of the
Independent JPEG Group’s free JPEG software. You are
welcome to redistribute this software and to use it for any
purpose, subject to the conditions under LEGAL ISSUES,
below.
(1) If any part of the source code for this software is
distributed, then this README file must be included, with
this copyright and no-warranty notice unaltered; and any
additions, deletions, or changes to the original files must be
clearly indicated in accompanying documentation.
Serious users of this software (particularly those
incorporating it into larger programs) should contact IJG
at jpeg-info@ uunet.uu.net to be added to our electronic
mailing list. Mailing list members are notified of updates and
have a chance to participate in technical discussions, etc.
This software is the work of Tom Lane, Philip Gladstone, Jim
Boucher, Lee Crocker, Julian Minguillon, Luis Ortiz, George
Phillips, Davide Rossi, Guido Vollbeding, Ge’ Weijers, and
other members of the Independent JPEG Group. IJG is not
affiliated with the official ISO JPEG standards committee.
(2) If only executable code is distributed, then the
accompanying documentation must state that “this software
is based in part on the work of the Independent JPEG
Group”.
LEGAL ISSUES
============
In plain English:
1. We don’t promise that this software works. (But if you find
any bugs, please let us know!)
2. You can use this software for whatever you want. You
don’t have to pay us.
3. You may not pretend that you wrote this software. If you
use it in a program, you must acknowledge somewhere
in your documentation that you’ve used the IJG code. In
legalese:
The authors make NO WARRANTY or representation, either
express or implied, with respect to this software, its quality,
accuracy, merchantability, or fitness for a particular purpose.
This software is provided “AS IS”, and you, its user, assume
the entire risk as to its quality and accuracy. This software
is copyright (C) 1991-1998, Thomas G. Lane. All Rights
Reserved except as specified below. Permission is hereby
granted to use, copy, modify, and distribute this software
(or portions thereof) for any purpose, without fee, subject to
these conditions:
(3) Permission for use of this software is granted only if
the user accepts full responsibility for any undesirable
consequences; the authors accept NO LIABILITY for
damages of any kind.
These conditions apply to any software derived from or
based on the IJG code, not just to the unmodified library. If
you use our work, you ought to acknowledge us. Permission
is NOT granted for the use of any IJG author’s name or
company name in advertising or publicity relating to this
software or products derived from it. This software may
be referred to only as “the Independent JPEG Group’s
software”. We specifically permit and encourage the use of
this software as the basis of commercial products, provided
that all warranty or liability claims are assumed by the
product vendor. ansi2knr.c is included in this distribution
by permission of L. Peter Deutsch, sole proprietor of its
copyright holder, Aladdin Enterprises of Menlo Park, CA.
ansi2knr.c is NOT covered by the above copyright and
conditions, but instead by the usual distribution terms of the
Free Software Foundation; principally, that you must include
source code if you redistribute it. (See the file ansi2knr.c
for full details.) However, since ansi2knr. c is not needed
as part of any program generated from the IJG code, this
does not limit you more than the foregoing paragraphs do.
The Unix configuration script “configure” was produced
with GNU Autoconf. It is copyright by the Free Software
Foundation but is freely distributable. The same holds for
its supporting scripts (config.guess, config.sub, ltconfig,
ltmain. sh). Another support script, install-sh, is copyright
by M.I.T. but is also freely distributable. It appears that
the arithmetic coding option of the JPEG spec is covered
by patents owned by IBM, AT&T, and Mitsubishi. Hence
arithmetic coding cannot legally be used without obtaining
one or more licenses. For this reason, support for arithmetic
coding has been removed from the free JPEG software.
(Since arithmetic coding provides only a marginal gain over
the unpatented Huffman mode, it is unlikely that very many
implementations will support it.) So far as we are aware,
there are no patent restrictions on the remaining code. The
IJG distribution formerly included code to read and write GIF
files. To avoid entanglement with the Unisys LZW patent,
GIF reading support has been removed altogether, and the
GIF writer has been simplified to produce “uncompressed
GIFs”. This technique does not use the LZW algorithm; the
resulting GIF files are larger than usual, but are readable by
all standard GIF decoders. We are required to state that “The
Graphics Interchange Format(c) is the Copyright property
of CompuServe Incorporated. GIF(sm) is a Service Mark
property of CompuServe Incorporated.”
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Samsung Techwin cares for the environment at all product manufacturing stages, and is
taking measures to provide customers with more environmentally friendly products.
The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly
products, and indicates that the product satisfies the EU RoHS Directive.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its
electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other
household waste at the end of their working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these items from other types
of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take these items for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should not be mixed with other
commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should
not be disposed of with other household waste at the end of their working life. Where marked, the
chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the
reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances
can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types
of waste and recycle them through your local, free battery return system.
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsung Techwin R&D Center, 6, Pangyo-ro 319beon-gil, Bundang-gu, Songnam-si, Gyeonggi-do 463-400, Korea
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
www.samsungipolis.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising