Si - College Hills Honda

Si - College Hills Honda
www.collegehillshonda.com
INSTALLATION
INSTRUCTIONS
Accessory
Application
Publications No.
2010 CIVIC
2-AND 4-DOOR (Si)
AII 42482
XM RADIO SYSTEM
PARTS LIST
XM Radio Attachment (sold separately):
P/N 08B15-SNA-100B
Issue Date
AUG 2009
20 Wire ties
(2 Not used)
Bus cable
7
Front bracket
Rear bracket
Wire ties with clip
(Some may not be used.)
12 Cushion tapes
(Some may not be used.)
Clip
8
4
EPT sealers
(Some may not be used.)
Pan screws
XM Antenna (sold separately):
P/N 08A15-0J1-100
Antenna assy
4
Washers
3
Flange bolts
Unit (sold separately):
P/N 08A15-3J1-000
XM radio unit
Cover seal
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42482 (0908)
08B15-SVB-1B01-91
1 of 20
www.collegehillshonda.com
2-Port Bus Cable (sold separately):
P/N 08A31-0F1-000
Illustration of the XM Radio System Installed on the
Vehicle
2-Port bus cable
2-door vehicle:
ANTENNA
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Ruler
Shop towel
Scissors
BUS CABLE
Ratchet
10 mm Socket
XM RADIO UNIT
10 mm Combination wrench
Isopropyl alcohol
(Isopropyl alcohol, in a 60/40 solution with water)
Rubber mallet
871609AR
4-door vehicle:
Masking tape
Diagonal cutters
Plastic Trim Tool (T/N SILTRIMTL10)
ANTENNA
TORX bit
BUS CABLE
XM RADIO UNIT
6623010H
2 of 20
AII 42482 (0908)
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
4.
AUDIO UNIT
Remove the two bolts under the glove box.
2 STOPS
GLOVE BOX
ANTENNA
BUS CABLE
XM RADIO UNIT
2 BOLTS
871506AR
871507AR
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
1.
Make sure you have the anti-theft codes for the
audio and navigation system (if equipped), then write
down the audio presets.
2.
Disconnect the negative cable from the battery.
3.
Remove the passenger’s dashboard lower cover
(four clips and two pins).
5.
Open and remove the glove box (two stops).
6.
Remove the driver’s dashboard lower cover (eight
clips).
DRIVER’S
DASHBOARD
LOWER COVER
8 CLIPS
5202121T
2 PINS
4 CLIPS
PASSENGER’S
DASHBOARD
871104AH
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42482 (0908)
3 of 20
www.collegehillshonda.com
7.
Remove the inside cover from the front console
pocket (two tabs).
SHIFT LEVER
“S or 2” POSITION
2 TABS
8.
10. Apply masking tape to the meter panel as shown,
and remove the meter panel (one self-tapping screw
and 11 clips, and unplug the vehicle connectors).
FRONT CONSOLE
POCKET
METER PANEL
INSIDE
COVER
VEHICLE
CONNECTORS
5202130T
Lower the tilt lever, then pull the steering wheel
toward you.
MASKING TAPE
SELF-TAPPING
SCREW
11 CLIPS
871508AR
11. Apply masking tape to the instrument panel as
shown. Remove the center panel (two bolts, 11 clips,
and aspirator hose, and unplug the vehicle
connectors).
COMBINATION
SWITCH
SHOP TOWEL
MASKING TAPE
5 CLIPS
ASPIRATOR
HOSE
VEHICLE
CONNECTORS
SHIFT LEVER
STEERING
WHEEL
SHOP
TOWEL
CENTER PANEL
TILT LEVER
6 CLIPS
BOLTS
871509AR
5608031H
9.
To protect the dashboard area, put shop towels over
the steering wheel and shift lever.
4 of 20
AII 42482 (0908)
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
12. Pull the weatherstrip off in the area shown.
14. Pull the weatherstrip off in the area shown. And
remove the right front pillar trim (two clips).
4-door vehicle:
FRONT PILLAR
2 CLIPS
RIGHT FRONT
PILLAR TRIM
PIN
CLIP
FRONT
PILLAR TRIM
CLIP
Strike
perpendicularly.
RUBBER
MALLET
WEATHERSTRIP
871511AR
RIGHT FRONT
PILLAR TRIM
WEATHERSTRIP
871510AR
2-door vehicle:
13. Push the clip into the vehicle side by striking the top
of the right front pillar trim in the part marked as
“SIDE CURTAIN AIRBAG” with the rubber mallet
perpendicularly to the vehicle. Then, remove the clip.
2 CLIPS
RIGHT FRONT
PILLAR TRIM
WEATHERSTRIP
871512AR
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42482 (0908)
5 of 20
www.collegehillshonda.com
M/T Vehicle
15. Remove the cap from the right sunvisor (four
retaining tabs).
•
Pull down on the shift boot. Remove the shift
knob by rotating counterclockwise.
VEHICLE
CONNECTOR
(If equipped.)
SHIFT KNOB
4 RETAINING
TABS
PARKING
BRAKE LEVER
(Pull up
completely.)
CAP
RIGHT
SUNVISOR
2 TORX
SCREWS
SUNVISOR
HOLDER
SHIFT BOOT
871513AR
16. Remove the right sunvisor (two T25 TORX screws,
and unplug the vehicle connector, if equipped).
17. Remove the sunvisor holder. Turn the holder 90°,
then pull it out.
5321061H
•
Remove the center console cover (five clips).
18. Remove the center console cover.
3 CLIPS
CENTER
CONSOLE
COVER
A/T vehicle:
Remove the center console cover (five clips).
2 CLIPS
3 CLIPS
CENTER
CONSOLE
COVER
2 CLIPS
5321072H
SHIFT LEVER
“N” POSITION
PARKING BRAKE LEVER
(Pull up completely.)
6 of 20
5202173T
AII 42482 (0908)
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
19. Open the center console lid, and remove the mat.
21. In the passenger’s compartment, remove the bolt
and then rear seat cushion (two hooks).
CLIP
4 BOLTS
2-door vehicle:
MAT
BOLT
CLIP
CENTER
CONSOLE
LID
CENTER
CONSOLE
VEHICLE
CONNECTOR
HOOKS
871108AH
871107AH
22. Open the trunk lid. Fold the rear seatback forward by
pulling the levers under the rear shelf. Remove the
trunk floor mat (two clips).
20. Remove the center console (four bolts and two clips,
and unplug the vehicle connector).
•
2-door vehicle: Go on to step 21.
•
4-door vehicle: Go to step 26.
REAR SEAT CUSHION
REAR SEATBACK
LEVER
LEVER
2 CLIPS
TRUNK
FLOOR
MAT
871109AH
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42482 (0908)
7 of 20
www.collegehillshonda.com
4-door vehicle:
23. Pull the trunk weatherstrip off in the area shown.
3 HOOKS
2 CLIPS
26. Remove the bolt and then rear seat cushion (two
hooks).
REAR
TRIM
PANEL
BOLT
TRUNK
WEATHERSTRIP
REAR SEAT CUSHION
HOOKS
871110AH
5202363T
27. Remove the bolt and then the right seat side bolster.
24. Remove the rear trim panel (two clips and three
hooks).
25. Pull the weatherstrip off. Remove the five clips and
then the right trunk side trim panel. Go to step 34.
RIGHT
SEAT SIDE
BOLSTER
CLIPS
WEATHERSTRIP
BOLT
RIGHT TRUNK
SIDE TRIM PANEL
8 of 20
3 CLIPS
(Turn the center pin in
a counterclockwise
direction to remove.)
5202410T
871111AH
AII 42482 (0908)
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
28. Remove the right rear side step trim (four clips and
three retaining tabs).
31. Pull the weatherstrip off in the area shown.
3 HOOKS
REAR TRIM PANEL
4 CLIPS
3 RETAINING
TABS
4 CLIPS
TRUNK
WEATHERSTRIP
FRONT
5202451T
RIGHT REAR SIDE
STEP TRIM
5202580T
29. Open the trunk lid. Fold the rear seatback forward by
pulling the levers under the rear shelf.
REAR
SEATBACK
32. Remove the rear trim panel (four clips and three
hooks).
33. Pull the weatherstrip off. Remove the five clips and
then the right trunk side trim panel.
2 CLIPS
2 LEVERS
CLIPS
CLIPS
(Turn the center pin
counterclockwise to
remove.)
WEATHERSTRIP
TRUNK
FLOOR MAT
5202441T
RIGHT TRUNK SIDE
TRIM PANEL
30. Remove the trunk floor mat (two clips).
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42482 (0908)
CLIP
(Turn the center pin
counterclockwise to
remove.)
5202472T
9 of 20
www.collegehillshonda.com
4-door vehicle:
Routing the Bus Cable
34. Route the bus cable from the trunk as shown.
2-door vehicle:
VEHICLE
BRACKET
SEAT BRACKET
BUS CABLE
BUS CABLE
RIGHT REAR
SEATBACK
871610AR
REAR
SEATBACK
BUS CABLE
35. Lift up and lock the rear seatback, then remove the
clip to pull back the floor carpet.
871112AH
FLOOR CARPET
CLIP
Route under
the floor
carpet.
BUS
CABLE
871113AH
36. Route the bus cable forward under the floor carpet.
10 of 20
AII 42482 (0908)
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
37. Route the bus cable along the vehicle harness
forward, then pull the bus cable connector out of the
dash opening.
Routing the Antenna Cable
38. With isopropyl alcohol on a shop towel, clean the
area shown on the inside of the front window.
INSIDE
DASH
OPENING
BUS CABLE
3 mm
(0.1 in.)
DASH
OPENING
10 mm
(0.4 in.)
ANTENNA
ANTENNA
FRONT
WINDOW
VEHICLE
HARNESS
4 ADHESIVE
BACKINGS
871520AR
39. Remove the adhesive backings from the antenna,
and attach the antenna to the location shown. Apply
sufficient pressure to completely contact.
BUS CABLE
871114AH
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42482 (0908)
11 of 20
www.collegehillshonda.com
40. Attach the masking tape to the location shown.
OUTSIDE
43. With scissors, cut three EPT sealers in half.
MASKING TAPE
EPT SEALER
(Cut in half.)
ANTENNA
6 mm
(0.24 in.)
Align with
end of the
masking tape.
6 HALF EPT
SEALERS
PASSENGER’S
A-PILLAR
5 mm
(0.2 in.)
ANTENNA
CABLE
VEHICLE HOLES
(Do not attach the
EPT sealers.)
871604AR
ADHESIVE
BACKING
44. Route the antenna cable down along the
passenger’s A-pillar. Using the six pieces of EPT
sealer, secure the antenna cable to the A-pillar panel
in the areas shown.
COVER
SEAL
871521AR
41. With isopropyl alcohol on a shop towel, clean the
area shown on the outside of the front window.
NOTE: Do not attach the half EPT sealers to the vehicle
holes, pay attention to the orientation of half EPT sealers.
42. Remove the adhesive backing from the cover seal,
then attach to the location shown. Remove the
masking tape.
12 of 20
AII 42482 (0908)
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
45. With scissors, cut one EPT sealer in half. Attach one
of the halved piece of the EPT sealer to the vehicle
bracket.
49. Route the antenna cable down along the bus cable
as shown.
WIRE TIES
ANTENNA CABLE
VEHICLE
HARNESS
WIRE TIES
300 mm
(11.8 in.)
BUS CABLE
CONNECTOR
DASHBOARD STAY
WIRE
TIES
ANTENNA CABLE
VEHICLE
BRACKET
871611AR
EPT SEALER (1/2)
5322011H
46. Route the antenna cable down behind the
dashboard stay and towards the glove box. Using
three wire ties, secure the antenna cable to the
vehicle harness.
50. Using six wire ties, secure the bus cable and
antenna cable to the vehicle harness as shown.
51. Route the antenna cable along the bus cable. Using
three wire ties, secure the bus and antenna cables to
the vehicle harness.
47. In the glove box opening, route the antenna cable
along the vehicle harness and towards the audio unit
opening.
CUSHION
TAPE
VEHICLE
HARNESS
VEHICLE
HARNESS
ANTENNA CABLE
ANTENNA
CABLE
WIRE TIES
BUS CABLE
CUSHION TAPES
871612AR
WIRE TIE
5322020H
48. Using one wire tie, secure the antenna cable to the
vehicle harness.
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
52. Secure the bus and antenna cables to the floor panel
using three cushion tapes in the areas shown after
thorough cleaning with isopropyl alcohol on a shop
towel.
53. Route the antenna cable along the bus cable. Turn
over the floor carpet. Using two cushion tapes,
AII 42482 (0908)
13 of 20
www.collegehillshonda.com
secure the bus and antenna cables to the floor panel
in the areas shown after thorough cleaning with
isopropyl alcohol on a shop towel.
WIRE TIES
2-door vehicle:
55. Route the antenna cable along the bus cable. Using
the two wire ties, secure the bus and antenna cables
to the vehicle harness in the areas shown.
BUS CABLE
BUS CABLE AND
ANTENNA CABLE
ANTENNA
CABLE
ANTENNA
CABLE
CUSHION
TAPE
BUS CABLE
Turn over.
VEHICLE
HARNESS
WIRE
TIES
CUSHION
TAPE
ANTENNA
CABLE
SIDE VIEW
871614BR
871613AR
54. Using three wire ties, secure the bus and antenna
cables to the vehicle harness in the areas shown.
•
2-door vehicle: Go on to step 55.
•
4-door vehicle: Go to step 57.
14 of 20
CUSHION
TAPES
56. Using three cushion tapes, attach the bus and
antenna cables to the floor panel in the areas shown
after thorough cleaning with isopropyl alcohol on a
shop towel. Go to step 59.
AII 42482 (0908)
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
4-door vehicle:
57. Route the antenna cable along the bus cable. With
two wire ties, secure the bus and antenna cables to
the vehicle harness in the areas shown.
59. Attach EPT sealers to the right trunk inner panel in
the areas shown after thorough cleaning using
isopropyl alcohol on a shop towel.
2-door vehicle:
BUS CABLE AND
ANTENNA CABLE
EPT SEALER
RIGHT TRUNK
INNER PANEL
VEHICLE BRACKET
Clean.
WIRE
TIES
CUSHION
TAPES
EPT SEALER
Clean.
RIGHT REAR
SEATBACK
871616AR
4-door vehicle:
VEHICLE HARNESS
871615AR
58. With four cushion tapes, secure the bus and antenna
cables to the floor panel in the areas shown after
thorough cleaning using isopropyl alcohol on a shop
towel.
RIGHT TRUNK
INNER PANEL
Clean.
EPT
SEALER
6718020H
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
AII 42482 (0908)
15 of 20
www.collegehillshonda.com
Installing the XM Radio Unit
2-door vehicle:
60. Using four pan screws and four washers, set the
front and rear brackets to the XM radio unit.
61. Route the bus and antenna cables through the hole
of the right trunk inner panel.
•
2-door vehicle: Go on to step 61.
•
4-door vehicle: Go to step 70.
RIGHT TRUNK
INNER PANEL
BUS CABLE
4 PAN SCREWS
FRONT
BRACKET
CUSHION
TAPE
ANTENNA
CABLE 1-PIN
CONNECTOR
ANTENNA
CABLE
REAR
BRACKET
4 WASHERS
XM RADIO
UNIT
BUS CABLE
14-PIN CONNECTOR
871617AR
XM RADIO UNIT
6622080H
62. Plug the bus cable connector and the antenna cable
connector into the XM radio unit.
63. Using one cushion tape, secure the bus and antenna
cables to the XM radio unit.
16 of 20
AII 42482 (0908)
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
64. Loosely tighten three flange bolts to the front and
rear brackets. On the front bracket, use the “B”
marked holes.
67. Using one wire tie with clip, secure the bus and
antenna cables in the area shown.
WIRE TIES WITH CLIP
in step 69
RIGHT TRUNK
INNER PANEL
ELONGATED
HOLES
XM RADIO
UNIT
FRONT
BRACKET
CUSHION TAPE
XM
RADIO
UNIT
REAR
BRACKET
FLANGE
BOLT
CUSHION
TAPE
Bundle the
excess cables.
RIGHT TRUNK
INNER PANEL
“B” MARKED
HOLE
FLANGE BOLT
871618AR
65. Place the XM radio assembly to the back of the right
trunk inner panel. Set the three flange bolts into the
elongated holes in the body panel.
66. Tighten the three flange bolts to secure.
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
WIRE TIE WITH CLIP
in step 67
871619BR
68. Using two cushion tapes, secure the bus and
antenna cables to the right trunk inner panel in the
area shown after thorough cleaning with isopropyl
alcohol on a shop towel.
69. Using two wire ties with clip, bundle the excess of the
bus and antenna cables, then tighten securely. Go to
step 78.
AII 42482 (0908)
17 of 20
www.collegehillshonda.com
4-door vehicle:
70. Plug the bus cable connector and the antenna cable
connector into the XM radio unit.
BUS CABLE
CUSHION
TAPE
75. Using one wire tie with clip, secure the bus and
antenna cables in the area shown.
WIRE TIES
WITH CLIP
in step 76
WIRE TIES WITH CLIP
in step 77
RIGHT TRUNK
INNER PANEL
ANTENNA
CABLE
ANTENNA
CABLE 1-PIN
CONNECTOR
WIRE TIE
WITH CLIP
in step 75
XM RADIO
UNIT
XM RADIO
UNIT
RIGHT TRUNK
INNER PANEL
BUS CABLE
14-PIN CONNECTOR
6718030H
71. Using one cushion tape, secure the antenna cable to
the XM radio unit in the area shown.
Bundle the
excess cables.
871621AR
76. Using three wire ties with clip, secure the bus and
antenna cables to the holes on the right trunk inner
panel.
77. Using two wire ties with clip, bundle the excess of the
bus cable and antenna cables, then tighten securely.
72. Loosely tighten three flange bolts to the front and
rear brackets. On the front bracket, use the
“A” marked holes.
ELONGATED
HOLES
RIGHT TRUNK
INNER PANEL
FRONT
BRACKET
XM RADIO
UNIT
FLANGE
BOLT
REAR
BRACKET
“A” MARKED
HOLE
FLANGE BOLT
871620AR
73. Place the XM radio assembly to the back of the right
trunk inner panel. Set the three flange bolts into the
elongated holes in the body panel.
74. Tighten the three flange bolts to secure.
18 of 20
AII 42482 (0908)
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
If the vehicle you’re working on is equipped with CD
Changer, go on to step 78; otherwise, go to step 80.
Audio Unit for 2-door vehicle
78. Plug the 2-port bus cable connectors in the two bus
cables.
AUDIO UNIT
BUS CABLE or
2-PORT
BUS CABLE
BUS CABLES
5801010H
2-PORT
BUS CABLE
Navigation Unit
2 EPT SEALERS
871530AR
NAVIGATION
UNIT
79. Attach two EPT sealers around the two plugged
connectors.
80. Plug the bus cable connector into the audio unit.
Audio Unit for 4-door vehicle
BUS CABLE or
2-PORT BUS CABLE
AUDIO UNIT
871129AH
BUS CABLE or
2-PORT BUS CABLE
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
871531AR
AII 42482 (0908)
19 of 20
www.collegehillshonda.com
81. Plug the vehicle connectors to the center panel, and
reinstall the center panel.
83. Check that all wire harnesses are routed properly
and all connectors are plugged in.
84. Reinstall all removed parts.
VEHICLE CONNECTORS
CENTER PANEL
85. Connect the negative cable to the battery and check
operation of all lights and other electrical
accessories.
86. Enter the anti-theft codes for the audio system and
the navigation system (if equipped), and reset the
radio station presets.
87. Reset the clock on vehicles without navigation.
88. Check the operation of the XM radio system
according to the vehicle’s owner’s manual.
BOLTS
(Reuse.)
5420071H
82. Replace the old clip on the right front pillar trim with
a new one.
NEW CLIP
OLD CLIP
(Discard.)
RIGHT FRONT
PILLAR TRIM
871622AR
20 of 20
AII 42482 (0908)
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising