High pressure cleaners e cleaners
GB
High pr
essur
e cleaners
pressur
essure
D 16/220
ual
n
a
m
ing
Ope rat
conform
nd
Read a i n s t r u c t i o n s
safety
use
before
Description
Dear Customer
We would like to congratulate you on your new portable/mobile high
pressure cleaner and to thank you for the purchase.
To ease your introduction to the use of the cleaner, we have provided the
following pages of explanations, tips and hints.
The equipment will assist you professionally in all cleaning tasks, e.g.:
- facades
- flagstones
- terraces
- vehicles of oll
types
- sheds
- channels
technical
specifications
operating pressure,
steplessly adjustable
- barrels and
containers
- machines
- streets
D 16/220
10 - 220 bar
permissible
overpressure
240 bar
water output
at 1800 rpm
16 l/min
hot water input up to
70 °C
suction height
2,5 m
high pressure hose
with hose drum
10 m
15 m
engine
Yanmar L100AE-S
weight
26 kg
Guaranteed sound
level LWA
103 dB(A)
Vibrations at lance
2,2 m/s²
recoil at lance
approx. 38 Nm
Permissible tolerance for figures ± 5 % in accordance with VDMA uniform sheet 24411
2
Description
10
8
9
2
7
water
4
5
3
6
1
Construction
The KRÄNZLE D 16/220 - high pressure cleaners
are mobile machines. The design can be seen from the diagram.
Item
6
1 Water inlet connection with filter
7
2 Suction hose with filter
8
(special accessory) order No. 15.038 3 9
3 High pressure pump
10
4 Pressure gauge with glycerin filling
5 Unloader valve - safety valve
Injector for cleaning agents
High pressure hose
Spray gun assembly
Interchangeable lance
Regulator nozzle
3
Description
Water - and Cleang - Care System
Water can be connected at mains pressure to the high pressure pump or it can be
sucked directly from a storage tank.
The water is then forced under pressure by the high pressure pump to the lance.
The high pressure jet is formed by the nozzle at the end of the lance.
Cleaning and caring agents can be mixed with the water by a low pressure injector.
Environmental, refuse disposal and water protection
regulations must be observed !
Lance with trigger gun
The machine can only be operated when the safety trigger is squeezed.
When the lever ist squeezed, the spray gun opens. The liquid is then pumped to the
nozzle. The spray pressure increases and quickly reaches the selected operating
pressure.
When the trigger ist released, the trigger gun closes and any further spraying of
liquid from the lance ist stopped.
The increase in pressure when the trigger gun is closed causes the unloader valvesafety valve to open. The pump remaines switched on and continues to pump liquid
through the pump at reducated pressure.
When the trigger gun ist opened, the unloader valve - safety valve closes and the
pump ressumes pressure spraying from the lance.
The trigger gun is a safety device. Repairs should only be performed by
qualified persons. Should replacement parts be required, use only
components authorized by the manufacturer.
Unloader valve - safety valve
The unloader valve - safety valve protects the machine from a build-up of excess
pressure, and is designed not to permit an excess pressure to be selected for
operating. The limit nut on the handle is sealed with a spray coating.
The operating pressure and spray rate can be steplessly adjusted by tuning the
handle.
Replacements, repairs, new adjustments and sealing should only be
performed by qualified persons.
4
Description
For the motor follow the Y
anmar
Yanmar
operating manual only
only..
Motor-safety:
(see Yanmar operating manual)
Yanmar motors are safe and reliable if they are operated correctly. Read the
operating manual carefully before using the motor and try to understand the
contents of the manual completely.
Not following this advice could lead to injuries or damage of the
equipment.
To avoid a possible fire hazard and to ensure the necessary ventilation
the motor has to be operated at a distance of at least 1 m from buildings
and objects. Inflammable objects have to be kept away from the
surrounding area of the motor.
Children and pets have to be kept away from the motor, as there is a
danger of suffering burns from hot motor parts and to be injured by
equipment driven by the motor.
Get to know the motor and especially learn how to switch it off quickly.
Do not allow persons to operate the motor who are not familiar with it.
Setting up: Location
Neither set up and operate the machine in rooms where there is a risk of
fire or explosion nor put it into puddles. Do not use the machine under
water.
CAUTION !
Never use liquid containing solvents such as paint thinners, petrol, oil or
similar liquid matter. Pay attention to the instructions of the
manufacturers of the cleaning agents. The seals in the
machine are not resistant to solvents. The spray of solvents is
inflammable, explosive and poisonous.
CAUTION !
When running your high pressure cleaner with hot water of 70° C raised
temperatures occur.
Do not touch the machine without safety gloves.
5
Description
Brief operating instructions
1. Connect the high pressure hose with spray gun
and machine.
2. Connect the suitable water supply.
3. Flush the air from the pump (open and close the spray gun
several times).
4. Switch on the motor while the spray gun is open and commence
cleaning.
5. After completing the work, completely empty the pump
(switch the motor on for approximately 20 seconds without the
suction and pressure hose).
Afterwards you can roll up the high pressure hose.
- Only use clean water ! Protect from frost !
CAUTION !
Please pay attention to the regulations of your waterworks company.
In accordance with EN 61 770, the machine may not be directly connected to the
public drinking water supply lines.
A brief connection however ist permissible according to DVGW (German
Association for Gas and Water Affairs) if a tube ventilator with check valve
(KRÄNZLE Order-No. 41.016 4) is built into the water supply.
Also indirect connection to the public drinking water supply lines is permissible by
way of free emission in accordance with EN 61 770; e.g. by using a reservoir with a
float valve.
Direct connection to a non-drinking water supply line is permissible.
High pressure hose and spray device
The high pressure hose and spray device supplied with the machine are made of
high grade material, they are also optimized for the machine and marked as
required by the appropriate regulations.
If replacement parts are required, only such parts that are authorized by
the manufacturer and which bear the markings required by the
appropriate regulations may be used. The high pressure hose and spray
device must be connected in a pressure-tight manner. The high pressure
hose may not be driven over, pulled excessively, or twisted. The hose
may under no circumstances be pulled over sharp edges, since
otherwise the guarantee is automatically void.
6
Safety notes
As to the recoil see notice on page 2.
Apply the safety catch on the
spray gun after each use, in
order to prevent
unintentional spraying.
Always aim the
underbody lance. Note
when using an angle
underbody lance, like
for example lance
No. 41.075, that there
is a certain amount of
torque (twisting
motion) in the recoil.
(See also notice on
page 2).
7
This is what you´ve purchased :
1. Spray lance with regulator and
high pressure nozzle, flat spray
2. Spray gun with insulated pistol
grip and screw connection
3. KRÄNZLE - High pressure cleaner
D 16/220
4. High pressure hose 10 m
15 m HP-hose for cleaners
with hose drum
6. Operating instructions pump
Operating instructions motor
5. Suction hose
7. Water inlet components
8
Prepare for use
1. Oil-measuring stick
2. Connect the high pressure
lance to the spray gun.
3. Unwind the high pressure hose
without leaving kinks or "nooses"
and connect it to the spray gun and
pump. When using extension
hoses, use max. 20 m high
pressure hose, or 2 x 10 m with
hose connectors.
The high pressure hose
connected from the machine to
the lance.
9
Preparation for use
4. The machine can be connected
to a pressurised water line with cold
or 60 °C respectively 70 °C hot water
(see page 2).
Ensure that the water supply ist clean
when sucking from external sources.
The hose cross section must be
at least 1/2" = 12.7 mm (free
passage). Filter 1 must
always be clean.
Please make
sure that the filter is
clean before using
your
high pressure cleaner.
CAUTION !
When running your high pressure cleaner with hot water of 70° C raised
temperatures occur.
Do not touch the machine without safety gloves.
5. Maximum induction height 2.5 m
- see technical data
on page 2.
Water
10
Preparation for use
Adjusting the pressure
This is accomplished by turning the handwheel.
The default setting is maximum pressure.
When using cleansing agents:
Place chemical filter no. 5 in the reservoir with
the cleansing agent. Turn on Vario-Jet No. 4 to
enable the injector to induct the cleansing
agent. By turning back the Vario-Jet nozzle, the
supply of chemical is automatically cut off.
Allow the cleansing agent to take effect and
then remove with high pressure spray.
p max.
Chem.
Turn on regulator nozzle
to reach low pressure.
A mixing ratio of 3-5% is achieved
when the Vario-Jet is fully turned on.
pH value neutral 7-9.
Note that you must always comply
with the instructions provided by the
manufacturer of the cleansing
agent (e.g. instructions
concerning safety clothing) and
the water protection egulations.
To shut down the pump:
1. Switch off the machine
2. Cut off the water supply
3. Open the spray gun briefly until the pressure is released
4. Apply the safety catch on the spray gun
5. Remove the water hose and high pressure hose
6. Drain the pump: switch on the motor for approx. 20 seconds
7. Winter: store the pump in rooms above 0° C
8. Clean the water filter
11
This is prohibited
Never allow
children to use the
high pressure
cleaner !
Never direct the
water jet at the
machine itself !
12
This is prohibited
Never direct the
water jet at people
or animals !
Never pull the high
pressure hose if it
has formed kinks or
"nooses"!
Never pull the hose
over sharp edges !
13
Additional KRÄNZLE accessories
Rotary scrubbing brush
Order No. 41.050 1
Drain and pipe
cleaning hose
8 m - Order No. 41.051
15 m - Order No. 41.058
Underbody lance, new
Order No. 41.075
Sandblaster
Order No. 41.068 1
Flat brush
Order No. 41.073
Dirtkiller
B 10/200
Order No. 41.073 8
B13/150
Order No. 41.072 5
Turbokiller
B 16/220
Order No. 41.072 4
14
Environmental, refuse disposal and water
protection regulations must be observed
when using the accessories.
for further combination possibilities
Car cleaning, glass, caravan, boat etc.:
rotary washing brush with 40 cm extension
and
ST 30 nipple M 22
Cleaning pipes, channels and drains: Pipe
cleaning hose with KN nozzle and
ST 30 nipple M 22.
Underbody cleaning of cars, trailers and
equipment: lance 90 cm with high pressure
nozzle and ST 30 nipple. The lance must
be aimed when spraying.
Blasting old paint, rust and facades:
sandblasting injector with suction lance and
3 m PVC hose and ST 30 nipple M 22.
When sandblasting you must
wear protection clothes! Pay
attention to the instructions of
the manufacturer of the
abrasive.
Cleaning cars and all smooth surfaces:
brush with ST 30 nipple M 22.
Rotary point sprayer for extreme soiling:
dirt killer with 40 cm extension and
ST 30 nipple M 22.
15
Small repairs –
You only get a weak flow of water or no water at all !
The pressure gauge shows a 10% higher pressure than the
working pressure.
The injector may be dirty
and you
should first
remove
the hose.
Now turn on the water
and you should get a
powerful stream of water,
but if you
only get a weak
flow of water
and release the
injector with an
open-ended
spanner.
Remove the injector
together with the
spring and return
valve.
then straighten
a paper clip,
Cleaning the injector through
from both sides and replace
the return valve.
Reconnect the hose,
16
Check that it
is clean.
and you are
ready to continue
your work.
Do it yourself !
The nozzle is blocked !
No water but the gauge shows full pressure.
Rinse the hose through
first.
You should now have
a powerful stream of
water,
Using the flat spray lance
you only have to clean the front
nozzle.
remove the lance and
clean the
nozzle.
Insert pointed opject
into the hole
and pull the cap back!
Check visually whether the
nozzle is clean.
but if you only
get a few drops
of water from
the lance,
Straighten a paper clip
and clean the nozzle.
Now it works as well
as before.
17
Small repairs - Do it yourself !
Valve dirty or sticky !
Pressure gauge does not show full pressure.
The high-pressure hose
Water comes out in spurts.
vibrates.
If you do not use the high pressure cleaner for some time the valves can stick.
When a valve is blocked.
the gauge
shows little
pressure or
no
pressure
at all.
or the high
pressure
hose vibrates!
remove the
valve screw, the
valve and the
O-ring.
Open the
valves with a
socket wrench...
and remove the dirt
from the valve - the
inside must be
closed.
Straighten a
paper clip...
Rplace the rubber
O-ring.
and repeat an
all 6 valves.
Retighten the
valve screw,
18
Now it works as
well as before.
General rules
Inspections:
The machine must be inspected according to the "Guidelines for Liquid
Spray Devices" at least once every 12 months by a qualified person, to
ensure that continued safe operation is guaranteed. The results of the
inspection are to be recorded in writing. This may be done in any form.
Accident prevention
The machine is designed for accidents to be impossible if used correctly.
The operator is to be notified of the risk of injury from hot machine parts and
the high pressure water jet. The "Guidelines for Liquid Spray Devices" must
be complied with. (see page 12 and 13)
Check the oil level with the oil-measuring stick prior to each use.
(Ensure horizontal position!)
Oil change D16/220:
The oil of your high pressure pump should be changed after approx. 40
hours of operation, or no later than when it takes an a grey or whitish colour.
Open the oilplug over a container and drain off all the oil. The oil must be
caught in a contianer and disposed of in a responsible, legal manner.
New oil: 1,0 l - Castrol Formula RS
Warranty
This warranty covers material and/or workmanship related defects only and does not
extend to ordinary wear.
Machine must be operated according to enclosed operating instructions which are part of
present warranty conditions.
All products sold directly to private customers are warrantied for a period of 24 months,
whereas the warranty period for industrial purchases is limited to 12 months.
In case of any warranty claims, please have your HP cleaner together with accessories
and your purchase document ready and contact your nearest dealer or authorized service
point which can also be looked up in the internet at www.kraenzle.com .
Warranty is void in case of attempts to modify any of the safety devices or in the event of
exceeding temperature or rpm limits - this also applies to undervoltage, low water and/or
polluted water. Gauge, nozzle, valves, sealing gaskets, high pressure hose and spray
equipment are considered wear parts and do not fall under this warranty.
19
Complete Assembly
20
KRÄNZLE
D 16/220
Spare parts list Profi-Jet D 16/220 with undercarriage
Complete Assembly
No.
Description
1
1a
2
3
6
7
8
9
10
11a
Wagen
1
Wagen kompl. (Pos. 1 + 3)
1
Sechskantschraube M 8 x 30
4
Schubbügel
1
Unterlegscheibe 8,4
8
Elastic-Stop-Mutter M 8
4
Hochdruckschlauch 1m / DN 8 - 210 bar 1
O-Ring 9,3 x 2,4
3
Chemiesieb mit 1,2 m PVC-Schlauch
1
at unit with hose drum
high pressure hose 15 m / DN 8 - 210 bar1
at unit without hose drum
high pressure hose 10 m / DN 8 -210 bar 1
Starlett II mit ISO-Handgriff
1
Lance with reg. nozzle 25055
1
prease specify size of nozzle
Saugschlauch 3 m mit Saugfilter
1
Turbokiller 055
1
Gummidämpfer
4
Starlock-Kappe
2
Rad luftbereift
2
Innensechskantschraube M 6 x 40
2
Flügelmutter M 6
2
Mutter M 6
1
Innensechskantschraube M 6 x 40
1
Pistolenablage
1
Schraube 2,9 x 19
2
Schlauchtrommel kpl. ohne Schlauch
1
Gummistopfen
2
Bügel
1
Elastic-Stop-Mutter M 8
2
15.038 3
41.072 4
40.220
40.142
40.141
40.133
40.132
14.127 1
40.133
40.130
15.024
41.259
40.208 1
41.101 6
41.514
Speedcontrol with 1m Bowden cable
40.255 1
11b
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Qty.
1
Ord.-No.
41.101 7
41.101 5
40.221
41.101 3
41.515 6
41.410
41.265
13.273
15.038
41.083
41.082
12.320 2
41.053 2
Motor Yanmar L100 AE-S
24.200
Upgrade kit hose drum
with 1 m HP-Connection hose
with 20 m HP-hose
41.259 1
21
Transmission unit
22
Description
Ölgehäuse
Cu-Dichtring
Ölablaßschraube
Innensechskantschraube M 8 x 25
Sicherungsscheibe
Flachdichtung
Öldichtung 20 x 30 x 7
Wellenscheibe
Axial-Rollenkäfig
AS-Scheibe
Swash plate 8° 30mm
Plungerfeder
Federdruckscheibe
Plunger 20 mm (lang)
Sprengring
O-Ring 14 x 2
Ölschauglas M 18 x 1,5
Flachdichtung
Deckel Ölgehäuse
Innensechskantschraube M 5 x 12
Ölmeßstab
Stützscheibe
Gehäusescheibe
Innensechkantschraube M 8 x 30
Kupfer-Dichtring
Dichtring 30 x 42 x 7
Flansch für D 16/220
Motor Yanmar L100 AE-S
Spannstift
Stufenkeil
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
24
25
26
27
28
30
52
53
1
1
1
6
6
1
3
1
1
2
1
3
3
3
3
2
1
1
1
4
1
3
1
4
4
1
1
1
1
1
Qty.
40.501
40.052
40.051
40.053
40.054
40.511
40.044 1
40.043
40.040
40.041
40.042 7-8,0°
40.506
40.510
40.505
40.048
43.445
42.018
41.019 3
40.518
41.019 4
42.520
40.513
40.039
41.036 1
41.500
40.224
40.225
24.200
14.148
40.222 1
Ord.-No.
Spare parts list Profi-Jet D 16/220
Transmission unit AQ-Pump
KRÄNZLE
D 16/220
23
Valve housing
24
Ventilgehäuse AQ mit integr. UL
ohne integr. Druckschalter
O-Ring 18 x 2
Einlaß- / Auslaß- Ventil
O-Ring 21 x 2
Ventilstopfen
Ventilstopfen mit R 1/4" IG
Sicherungsring
Innensechskantschraube M 12 x 45
Sauganschluß R 1/2" AG
Wassereingangsfilter
Gewebemanschette
Backring 20 mm
O-Ring 31,42 x 2,62
Leckagering 20 x 36 x 13,3
Cu-Dichtring 21 x 28 x 1,5
Gummimanschette
Verschlußschraube R 1/2"
Distanzring mit Abstützung
Druckring 20 mm
Zwischenring 20 mm
Dichtring 17 x 22 x 1,5 (Kupfer)
Anschlußmuffe 3/8" AG x 3/8" IG by
version with control speed
Verschlußschraube 3/8" AG by
version without control speed
1
30.1
2
3
4
5
5.1
6
7
8
9
13
14
15
16
17
18
19
20
23
24
29
30
Description
No.
1
6
6
6
5
1
4
4
1
1
3
6
3
3
1
3
1
3
3
3
1
1
1
Qty.
40.018
40.016
42.024
42.025
42.026
42.026 2
40.032
40.504
41.016 1
41.046 2
40.023
40.025
40.508
40.509
42.039
40.512
42.032
40.507
40.021
40.516
40.019
13.136
40.521
Ord.-No.
50
Repair kit Valves
consisting of:
6x No. 2; 6x No. 3; 6x No. 4
40.062 1
40.517
Repair kit sleeves without
brassparts consisting of:
3x No. 13; 6x No. 14; 3x No. 15;
3x No. 18; 3x No. 23
41.047 3
43.043
14.121
14.122
14.120
43.446
43.447
13.236
13.238
13.239
41.047 1
41.047 2
41.047 4
40.065 1
1
1
1
1
1
1
1
1
1
1
1
1
Ord.-No.
Repair kit sleeves
consisting of: 3x No. 13; 6x No. 14;
3x No. 15; 3x No. 16; 3x No. 18;
3x No. 20; 3x No. 23
Dichtstopfen M 10 x 1
O-Ring 6 x 3
Rückschlagkörper
Rückschlagfeder
O-Ring 18 x 2
Ausgangsstück Injektor ST30 M22x1,5
Saugzapfen Schlauchanschluß
Edelstahlkugel 5,5 mm
Edelstahlfeder
Gummidichtung für Steckkupplung
Steckkupplung für Wassereingang
Steckkupplung kpl.
Pos. 10 - 12
O-Ring
31
34
35
36
37
38
39
40
41
48
49
49.1
Qty.
Description
No.
Spare parts list Profi-Jet D 16/220
Valve housing AQ-Pump
KRÄNZLE
D 16/220
25
Unloadervalve
26
Description
O-Ring 16 x 2
O-Ring 11 x 1,44
Edelstahlsitz
Sicherungsring
Edelstahlkugel
Edelstahlfeder
Verschlußschraube
Steuerkolben
Parbaks 16 mm
Parbaks 8 mm
Spanstift
Kolbenführung spezial
Kontermutter M 8 x 1
Ventilfeder schwarz
Federdruckscheibe
Nadellager
Handrad
Elastic-Stop-Mutter M 8 x 1
Manometer 0-400 Bar
Aluminium-Dichtring
No.
5
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
25
26
27
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
Qty.
13.150
12.256
14.118
13.147
13.148
14.119
14.113
14.134
13.159
14.123
14.148
42.105
14.144
14.125
14.126
14.146
14.147
14.152
15.039 4
13.275
Ord.-No.
Spare parts list Profi-Jet D 16/220
Unloadervalve AQ-Pump
KRÄNZLE
D 16/220
27
Hose drum
28
Description
Seitenschale Schlauchführung
Seitenschale Wasserführung
Trommel Unterteil
Trommel Oberteil
Innensechskantschraube M 4 x 25
Lagerklotz mit Bremse
Lagerklotz links
Klemmstück
Kunststoffschraube 5,0 x 20
Antriebswelle
Welle Wasserführung
Elastic-Stop-Mutter M 4
Handkurbel
Verriegelungsbolzen
Scheibe MS 16 x 24 x 2
Wellensicherungsring 22 mm
Wellensicherungsring 16 mm
Parbaks 16 mm
Sicherungsscheibe 6 DIN6799
Schraube M 5 x 10
Drehgelenk
Anschlußteil
Distanzring
O-Ring 6,68 x 1,78
O-Ring 6 x 1,5
Stopfen M 10 x 1
O-Ring 9,3 x 2,4
Hochdruckschlauch 20 m NW 8
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
20
21
22
23
24
25
27
33
34
42
45
1
1
1
1
4
1
1
2
12
1
1
4
1
1
1
2
1
2
1
1
1
1
1
1
1
1
4
1
Qty.
40.302
40.301
40.304
40.303
40.313
40.306
40.305
40.307
43.018
40.310
40.311
40.111
40.309 9
40.312
40.181
40.117
40.182
13.159
40.315
43.021
40.167
40.308 1
40.316
40.585
13.386
13.385
13.273
41.083
Ord.-No.
51
52
53
54
55
56
57
No.
41.259 1
1
2
3
4
5
6
8
Hose Drum kpl.
with Schlauch
40.309
40.309
40.309
40.309
40.309
40.309
40.309
Ord.-No.
41.259 0
1
1
1
1
1
1
1
Qty.
Hose Drum kpl.
without Schlauch
Kurbelarm
Hülse
Druckfeder
Bolzen
Griff mit Kappe und Gleitscheibe
Spannstift 4 x 28
Flachsprengring SW18
Description
Spare parts list Profi-Jet D 16/220
Hose Drum
KRÄNZLE
D 16/220
29
Speed control
Spare parts list Profi-Jet B 16/220
Speed control
30
No.
Description
1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Grundteil
Druckhülse
Steuerkolben
Querbolzen
Druckfeder 2,0 x 9,5 x 70
Gewindestift M4 x 6 DIN 913-A2
Parbaks 7 mm
Bowdenzug 1 m
Unterlegscheibe 6,4 DIN 125
Sechskantmutter M6 DIN 934
Anschlussmuffe Drehzahlregulierung
Überwurfmutter
Klemmhülse
Einschraubwinkelverschraubung
Drosselscheibe
Gewindestift M 6 x 12 DIN915
Klemmbolzen
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Ord.-No.
42.581
42.584
42.582
42.583
42.587
42.592
15.013
42.586
50.189
14.127 1
42.585
40.075
40.074
44.092
42.589
42.590
42.591
Starlet II - Pistole
Spare parts list Profi-Jet D 16/220
Starlet II
No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Ventilkörper mit Handgriff
Schutzhülse
Abdeckschutz
Betätigungshebel
Sicherungshebel
Abschlußschraube M 16 x 1
Stopfen
Gewindeführungshülse R 1/4" AG
Aufsteuerbolzen
Stift
Lagernadel
Edelstahlfeder
Edelstahlkugel
Edelstahlsitz
O-Ring 11 x 1,44
O-Ring 3,3 x 2,4
Blechschraube 3,9 x 8
Druckstück
Rohr kunststoffumspritzt
bds. R 1/4" AG
Überwurfmutter ST30 M 22 x 1,5 IG
Außen-Sechskant-Nippel R 1/4" IG
O-Ring 9,3 x 2,4
Aluminium-Dichtring
O-Ring 15 x 1,5
Sicherungsring
20
21
22
23
24
25
Qty.
Ord.-No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
12.294
12.295
12.296
12.298
12.149
12.247
12.287
12.250
12.284
12.148
12.253
12.246
12.245
13.146
12.256
12.136
12.297
12.252
15.004 5
1
1
1
4
1
1
13.276 1
13.277 1
13.273
13.275
12.129 1
12.258
Starlet - Gun with extention
12.320 2
Repair kit "Starlet II"
consisting of No. 9,10,13,14,15
12.299
31
Turbokiller
Spare parts list Profi-Jet D 16/220
Turbokiller 055
32
No.
Description
11
12
13
14
15
16
17
18
19
20
21
22
23
Sprühkörperschutz
Sprühkörper
O-Ring 6,88 x 1,68
Düsensitz
Düse 055
Ring
Rotor
Stabilisator
O-Ring 41 x 1,78
Deckel
Deckelschutz
Rohr 500 mm lang; bds. R1/4"
Nippel M22x1,5 x R1/4" IG
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
Ord.-No.
41.528
41.529
41.521
41.522
41.532
41.533
41.534
41.524
41.538
41.539
41.540
12.385 1
13.370
Turbokiller 055 compl. with Lance
41.072 4
Rep. kit Turbokiller 055
41.097 1
Standard regulation nozzle
Spare parts list Profi-Jet D 16/220
Standard reg. nozzle
No.
Description
30
31
32
33
Nippel ST30 M22x1,5 AG / M 12 x 1
Rohr 400 mm, bds. M 12 x 1
Regeldüse mit Regulierring
Flat spray nozzle 2505
Qty.
1
1
1
1
Ord.-No.
13.363
15.002
13.201 2
26.001
Please specify size of nozzle
33
Inspirection report
for KRÄNZLE - High Pressure Cleaners
Regular inspection every 12 months if used professionally!
Appliance No:
Type:
The following must be checked:
1. Safety features
2. General condition
a) Manometer
b) Safety valve (pressure control)
c) Operating pressure
d) Cut out pressure (max. 10% above
a) High pressure hose
b) Spray gun
c) Motor
d) Oil level
operating pressure)
e) Low pressure with trigger released
The information in the operating instructions are a part of the inspection
Result of
inspection:
Date of inspection:
Faults rectified,
Stamp and signature
Excerpt from the Guidelines for Liquid Spray Equipment (ZH 1/46) by the Central Office of
the Professional Trade Association.
Inspection:
Liquid spray equipment should be inspected for safe operation by a qualified person
whenever necessary, but no less than every 12 months. The maker’s or supplier’s
instructions must be followed. The inspection intervals may be extended if the equipment
is not in active use.
In Germany, inspections compliant with the (German) Emission Controls Act may be
required for oil and gas-fired equipment, and the owner must arrange for these to be
carried out independently of the main inspection.
The results of inspections must be recorded in writing and presented to the respective
authorities on demand. There is no set form for these records.
34
High-pressure-cleaners
Nettoyeurs à haute pression
Hochdruckreiniger
I. Kränzle GmbH
Elpke 97 . 33605 Bielefeld
EC declaration of conformity
We hereby declare,
that the high-pressure models:
Kränzle D16/220
(techn. documentation available from):
Manfred Bauer, Fa. Josef Kränzle
Rudolf-Diesel-Str. 20, 89257 Illertissen
comply with the following guidelines and
specifications and their amendments for
high-pressure cleaners:
Machine guideline 89/392/EEC
Low voltage guideline 73/23 EEC
Specification for electromagnetic
compatibility 89/336 EEC
Outdoor noise directive 2000/14/EC,
Art. 13, High-pressure water jet machines
Appendix 3, part B, chapter 27
Sound power level
100 dB (A)
103 dB (A)
measured:
guaranteed:
Applied specifications and
standards:
EN 60 335-2-79:2004
EN 55 014-1 / A2:2002
EN 55 014-2 / A1:2001
EN 61 000-3-2 / A14:2000
EN 61 000-3-3 / A1:2001
Bielefeld, den 08.09.05
(Managing Director)
35
Reprint only allowed with the authorization of
As date of 15/05/08
.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising