Accessory INSTALLATION INSTRUCTIONS AUTOMATIC DAY/NIGHT MIRROR WITH COMPASS (DX, LX) PARTS LIST Automatic Day/Night Mirror with Compass P/N 08V03-SDA-100B Day/night mirror Spring Owner's Manual Automatic Day/Night Mirror Attachment Kit P/N 08V03-SDA-104 Short upper mirror cover Short lower mirror cover Long upper mirror cover (Not used) Long lower mirror cover (Not used) Application Publications No. AII 27519-28252 2005 ACCORD 2- AND 4-DOOR Issue Date SEP 2004 TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Small flat-tip screwdriver 10 mm Combination wrench Diagonal cutters Ratchet 8 mm and 10 mm Sockets Drill 7 mm Drill bit T25 Torx bit Torque wrench Isopropyl alcohol Shop towel Piece of steel wire Electrical tape Eye protection (face shield, safety goggles, etc.) Tape measure Long nose pliers Scissors Illustration of the Day/Night Mirror Installed on the Vehicle MIRROR HARNESS DAY/NIGHT MIRROR Day/night mirror harness Mirror harness 9 Wire ties 5 Cushion tapes © 2004 American Honda Motor Co., Inc - All Rights Reserved. DAY/NIGHT MIRROR HARNESS AII 27519-28252 (0409) 08V03-SDA-1000-91 1 of 8 INSTALLATION 5. Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 3. Remove the left and right lens front the roof console (six retaining tabs). Remove the sunvisor holders. Using a flat-tip screwdriver, push the hook, and turn the holder 90°, then pull it out. ROOF CONSOLE SUNVISOR HOLDER FLAT-TIP SCREWDRIVER RIGHT LENS 2306031M LEFT LENS 6. RETAINING TABS (6) RETAINING TABS (6) Remove the cap from the left sunvisor (four retaining tabs). 2306010M 4. Remove the roof console (four bolts, and unplug two connectors). CONNECTOR LEFT SUNVISOR CONNECTOR CAP RETAINING TABS (4) ROOF CONSOLE TORX SCREW GROUND BOLT 2306040M 5 mm BOLT 4623030Y 5 mm BOLT 7. GROUND BOLT 2 of 8 AII 27519-28252 (0409) Remove the left sunvisor (two T25 Torx screws and unplug the connector). © 2004 American Honda Motor Co., Inc - All Rights Reserved. 8. Remove the weatherstrip from the opening edge of front door in the area shown, then remove the left front pillar trim (with curtain side airbag: one pin and one clip; without curtain side airbag: two clips). 9. LEFT FRONT PILLAR TRIM WITH CURTAIN SIDE AIRBAG Remove the driver’s dashboard lower cover: • Remove the self-tapping screw. • Release the four clips on the left side first by pulling out on the driver's dashboard lower cover. • After releasing the four clips, insert the flat-tip screwdriver between the clip and the dashboard frame. Gently twist the screwdriver to release the clip. • Release the two clips on the right side last. • Unplug the vehicle connector, and remove the lower cover. PIN CLIPS (2) LEFT FRONT PILLAR TRIM VEHICLE CONNECTOR CLIP (Release these clips first.) CLIP (Release these clips last.) WEATHERSTRIP 2306050M VEHICLE FRAME CLIPS (7) SELF-TAPPING SCREW DRIVER'S DASHBOARD LOWER COVER FLAT-TIP SCREWDRIVER CLIP (Release the clip by inserting the flat-tip screwdriver between the clip and the dashboard frame, and twist the screwdriver to release the clip.) © 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27519-28252 (0409) 3 of 8 10. If equipped, remove the driver’s dashboard under cover (release the three retaining clips, one pin, and one holder). 12. Replace the spring. Slide the day/night mirror stay onto the mirror holder, then turn the mirror stay counterclockwise as shown. VEHICLE SPRING (Replace.) MIRROR HOLDER Turn the mirror stay counterclockwise. HOLDER DAY/NIGHT MIRROR MIRROR HOLDER RETAINING CLIPS (3) DRIVER’S DASHBOARD UNDER COVER PIN MIRROR STAY 2311041M 11. Remove the rearview mirror from the holder by rotating the stay clockwise. 2307020M STAY MIRROR HOLDER 13. Plug the mirror harness 7-pin connector into the rear of the mirror, then route the 3-pin connector up and out through the console opening in the roof lining as shown. CONSOLE OPENING IN ROOF LINING ROOF LINING MIRROR HARNESS MIRROR HARNESS 3-PIN CONNECTOR DAY/NIGHT MIRROR REARVIEW MIRROR MIRROR HARNESS 7-PIN CONNECTOR 2311011M 2306061M 4 of 8 AII 27519-28252 (0409) © 2004 American Honda Motor Co., Inc - All Rights Reserved. 14. On the short lower mirror cover, measure and cut off the ribs shown. SHORT LOWER MIRROR COVER DRILL (7 mm drill bit) 17. Attach a piece of steel wire to the day/night mirror harness 3-pin connector, and wrap electrical tape around the wire and the day/night mirror harness. Pull the 3-pin connector up along the instrument panel side bracket and out though the clearance between the left front pillar and the instrument panel. INSTRUMENT PANEL LEFT PILLAR RIBS Cut area RIBS Cut area DAY/NIGHT MIRROR HARNESS 3-PIN CONNECTOR 3 mm 15 mm DAY/NIGHT MIRROR HARNESS 3-PIN CONNECTOR 15. While wearing eye protection, drill a 7 mm hole through the existing hole on the lower cover as shown. 16. Measure the mirror harness in the area shown. Slide the end of the upper cover into the lower cover, then route the mirror harness through the grooves in the covers. Attach the lower cover to the stay of the mirror, and slide the upper cover to the edge of the roof liner. ROOF LINING LOWER MIRROR COVER HARNESS PIECE OF STEEL WIRE ELECTRICAL TAPE 18. Remove the electrical tape and the wire from the day/night mirror harness. DAY/NIGHT MIRROR STAY UPPER COVER LOWER COVER 110 mm DAY/NIGHT MIRROR 2311031M © 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27519-28252 (0409) 5 of 8 19. Route the day/night mirror harness 3-pin connector up along the left front pillar and out through the roof console opening along side the vehicle behind the roof lining. 3-PIN CONNECTOR 22. Secure the day/night mirror harness and the mirror harness to the vehicle harness with four wire ties. With Vehicle Harness: VEHICLE HARNESS MIRROR HARNESS WIRE TIES (4) DAY/NIGHT MIRROR HARNESS DAY/NIGHT MIRROR HARNESS 3-PIN CONNECTOR CUSHION TAPE With Vehicle Harness and i -VES: 20. Connect the day/night mirror harness 3-pin connector to the mirror harness 3-pin connector. Wrap one cushion tape around the connectors. VEHICLE HARNESS 21. Inside the roof lining, secure the mirror harness to the vehicle harness with the one wire tie. Secure the day/night mirror harness on the vehicle panel with two cushion tapes. VEHICLE PANEL WIRE TIE MIRROR HARNESS WIRE TIES (4) DAY/NIGHT MIRROR HARNESS VEHICLE HARNESS CUSHION TAPE LEFT PILLAR VEHICLE HARNESS DAY/NIGHT MIRROR HARNESS 6 of 8 CUSHION TAPE DAY/NIGHT MIRROR HARNESS i -VES HARNESS DAY/NIGHT MIRROR HARNESS VEHICLE PANEL AII 27519-28252 (0409) © 2004 American Honda Motor Co., Inc - All Rights Reserved. Without Vehicle Harness: • NOTE: If you are also installing another accessory that uses the 6-pin connector, remove the dummy connector from the 6-pin connector taped to the day/night harness. Connect the 6-pin connector from the other accessory harness into the 6-pin connector you just unplugged. Using isopropyl alcohol and a shop towel, thoroughly clean the areas where the cushion tape will attach. Using scissors, cut two cushion tapes in half, then secure the day/ night mirror harness to the left front pillar with the four half cushion tapes. DAY/NIGHT MIRROR HARNESS 6-PIN CONNECTOR CUSHION TAPE (Cut in half.) HALF CUSHION TAPE FUSE BOX DUMMY CONNECTOR LEFT FRONT PILLAR OTHER ACCESSORY HARNESS 6-PIN CONNECTOR DAY/NIGHT MIRROR HARNESS 23. Plug the day/night mirror harness 6-pin connector into the fuse box located behind the kick panel. FUSE BOX 24. Unplug the vehicle 4-pin connector and the vehicle 24-pin connector. Connect the day/night mirror harness 24-pin connector in between the vehicle harness 24-pin connector. DAY/NIGHT MIRROR HARNESS 6-PIN CONNECTOR VEHICLE 24-PIN CONNECTOR 24-PIN CONNECTORS OF DAY/NIGHT MIRROR HARNESS FRONT VEHICLE 4-PIN CONNECTOR (Gray) DAY/NIGHT MIRROR HARNESS 6-PIN CONNECTOR VEHICLE 24-PIN CONNECTOR (White) 25. Reconnect the vehicle 4-pin connector. © 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27519-28252 (0409) 7 of 8 26. Loosen the ground bolt, and slide the ground terminal of the day/night mirror harness with onto the ground bolt. Then retighten the ground bolt. 29. Reinstall all removed parts. Check that all clips and fasteners are installed securely. DAY/NIGHT MIRROR HARNESS GROUND TERMINAL Do not attach the ground terminal. 28. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in. 30. Reconnect the negative cable to the battery. GROUND BOLT 31. Enter the customer’s radio anti-theft code, and reset the radio station presets. DAY/NIGHT MIRROR HARNESS 32. Reset the clock. 33. Check the operation of the automatic day/night mirror according to the Owner’s Manual supplied. NOTE: Whenever the battery is disconnected, the driver’s AUTO function is disabled. 34. Start the engine. Push down on the driver’s window switch until the window is fully open. 35. Pull up on the driver’s window switch fully to close the window completely, then hold the switch for 2 seconds or more. 36. Test the driver's window AUTO function. 27. Secure the day/night mirror harness to the vehicle harness with two wire ties. VEHICLE HARNESS WIRE TIE DAY/NIGHT MIRROR HARNESS 8 of 8 AII 27519-28252 (0409) © 2004 American Honda Motor Co., Inc - All Rights Reserved.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project