DIGITAL CAMERA X-Pro2

DIGITAL CAMERA X-Pro2
BL00004863-201
DIGITAL CAMERA
X-Pro2
New Features Guide
Version 2.00
Features added or changed as a result of firmware updates may no longer match the
descriptions in the documentation supplied with this product. Visit our website for
information on the updates available for different products:
http://www.fujifilm.com/support/digital_cameras/software/fw_table.html
EN
Contents
Please note the following changes and additions to the features described in the camera manual.
Description
X-Pro2 P
Flash setup has changed.
78, 79
The content of the shooting menu F FLASH FUNCTION SETTING item
FLASH SETTING
98
have changed.
Editing the Quick Menu The items that can be assigned to the quick menu have changed.
49, 112
Assigning Roles to the
The roles that can be assigned to the function buttons have changed.
51, 112
Function Buttons
An AUTO POWER SAVE option has been added to D POWER MANAGEAUTO POWER SAVE
114
MENT in the setup menu.
15 SEC, 30 SEC, and 1 MIN options have been added to D POWER MANAUTO POWER OFF
114
AGEMENT > AUTO POWER OFF in the setup menu.
A Y XS.S OPERATION option has been added to D BUTTON/DIAL SET36, 38, 57,
Y XS.S OPERATION
TING in the setup menu. Select OFF to disable shutter-speed fine-tuning
112
using the command dials.
The options available for G AF/MF SETTING > NUMBER OF THE FONUMBER OF THE FOCUS
CUS POINTS in the shooting menu are now 91 POINTS (7 × 13) and 325 67–70, 91
POINTS
POINTS(13 × 25).
The display when OFF is selected for G AF/MF SETTING > CORRECTED AF
CORRECTED AF FRAME
94
FRAME in the shooting menu has changed.
No.
Section
1 Flash Photography
2
3
4
5
6
7
8
9
ENGLISH
See P Ver.
EN-1
EN-2
EN-9
EN-9
EN-10
—
—
—
EN-11
2.00
Changes and Additions
3 Select FLASH FUNCTION
Flash Photography
FLASH SETTING
FLASH FUNCTION SETTING
RED EYE REMOVAL
TTL-LOCK MODE
LED LIGHT SETTING
MASTER SETTING
CH SETTING
X-Pro2 Owner’s Manual: P 78, 79
Flash setup has changed.
SETTING in the F FLASH
SETTING menu.
1 Remove the hot shoe cover and slide the flash onto
Q If the flash is not raised, settings will be adjusted
for units connected via the sync terminal (EN-3).
EXIT
the hot shoe as shown, stopping when it clicks into
place.
4 Highlight items using the
MODE
SUPPLIED FLASH
selector and rotate the rear
command dial to change the
highlighted setting.
ADJUST
END
5 Press DISP/BACK to put the changes into effect.
Q Depending on the distance to the subject, some
lenses may cast shadows in photos taken with the
flash.
Q The flash will not fire at some settings, for example
when the electronic shutter is used.
Q Choose shutter speeds slower than 250X when using the flash in exposure mode S (shutter-priority
AE) or manual (M).
2 Turn the flash on.
R For more information, see the documentation
provided with the flash unit.
R In TTL mode, the flash may fire several times with
each shot. Do not move the camera until shooting
is complete.
ENGLISH
EN-1
Changes and Additions
Red-Eye Removal
Red-eye removal is available when an option other
than OFF is selected for F FLASH SETTING > RED
EYE REMOVAL and G AF/MF SETTING > FACE/EYE
DETECTION SETTING is ON. Red-eye removal minimizes “red-eye” caused when light from the flash is
reflected from the subject’s retinas.
Flash Sync Speed
The flash will synchronize with the shutter at shutter
speeds of 1/250 s or slower.
Optional Flash Units
The camera can be used with optional FUJIFILM
shoe-mounted flash units.
Optional Flash Units
Do not use third-party flash units that apply over
300 V to the camera hot shoe.
F FLASH SETTING
X-Pro2 Owner’s Manual: P 98
The content of the shooting menu F FLASH FUNCTION SETTING item have changed.
FLASH SETTING
To adjust flash-related settings,
press MENU/OK in the shooting
display and select the F (FLASH
SETTING) tab.
Q The options available vary with the shooting mode
selected.
FLASH FUNCTION SETTING
RED EYE REMOVAL
TTL-LOCK MODE
LED LIGHT SETTING
MASTER SETTING
CH SETTING
EXIT
FLASH FUNCTION SETTING
Choose a flash control mode, flash mode, or sync mode
or adjust the flash level. The options available vary with
the flash.
Option
Description
Available with units connected via the sync terSYNC
minal and with third-party and other units that
TERMINAL
use only the X-contact on the hot shoe. Also displayed if no flash unit is connected (EN-3).
SHOE MOUNT Displayed when an optional flash unit is mountFLASH
ed on the hot shoe and turned on (EN-3).
Displayed if an optional flash unit functioning as a
MASTER
master flash for FUJIFILM optical wireless remote
(OPTICAL)
flash control is connected and turned on (EN-5).
R SYNC TERMINAL will also be displayed if the flash is attached but not raised.
EN-2
ENGLISH
Changes and Additions
SYNC TERMINAL
The following options are
available when a flash unit is
connected via the sync terminal.
SHOE MOUNT FLASH
The following options are
available with optional shoemounted flash units.
■
■
MODE
SYNC TERMINAL
ADJUST
MODE
SHOE MOUNT FLASH
ADJUST
END
A Flash control mode: Choose from the options below.
END
A Flash control mode: The flash control mode selected with the
• M: A trigger signal is transmitted from the sync terminal
and hot shoe when a picture is taken. Choose a shutter
speed slower than the sync speed (1/250 s); even slower
speeds may be required if the unit uses long flashes or
has a slow response time.
• OFF: The sync terminal and hot shoe do not transmit a
trigger signal.
flash unit. This can in some cases be adjusted from the
camera; the options available vary with the flash.
• TTL: TTL mode. Adjust flash compensation (B).
• M: The flash fires at the selected output regardless of subject brightness or camera settings. Output in some cases
can be adjusted from the camera (B).
• MULTI: Repeating flash. Compatible shoe-mounted flash
units will fire multiple times with each shot.
• OFF: The flash does not fire. Some flash units can be
turned off from the camera.
B Sync: Choose whether the flash is timed to fire immediately
after the shutter opens (1ST CURTAIN) or immediately before it closes (2ND CURTAIN). 1ST CURTAIN is recommended in
most circumstances.
B Flash compensation/output: The options available vary with
flash control mode.
• TTL: Adjust flash compensation (the full value may not
be applied if the limits of the flash control system are
exceeded). In the cases of the EF-X20, EF-20, and EF-42,
the selected value is added to the value selected with
the flash unit.
• M/MULTI: Adjust flash output (compatible units only).
Choose from values expressed as fractions of full power, from 1/1 (mode M) or 1/4 (MULTI) down to 1/512 in increments equivalent to 1/3 EV. The desired results may not
be achieved at low values if they exceed the limits of the
flash control system; take a test shot and check the results.
The Sync Terminal
Use the sync terminal to connect
flash units that require a sync cable.
ENGLISH
EN-3
Changes and Additions
C Flash mode (TTL): Choose a flash mode for TTL flash control.
F Lighting: If the unit supports this feature, choose from the
• FLASH AUTO: The flash fires only as required; flash level is
adjusted according to subject brightness. A p icon
displayed when the shutter button is pressed halfway
indicates that the flash will fire when the photo is taken.
• STANDARD: The flash fires with every shot if possible; flash
level is adjusted according to subject brightness. The
flash will not fire if not fully charged when the shutter
is released.
• SLOW SYNC.: Combine the flash with slow shutter speeds
when photographing portrait subjects against a backdrop of night scenery. The flash will not fire if not fully
charged when the shutter is released.
options below.
• FLASH POWER PRIORITY: Gain range by slightly reducing
coverage.
• STANDARD: Match coverage to picture angle.
• EVEN COVERAGE PRIORITY: Slightly increase coverage for
more even lighting.
D Sync: Control flash timing.
• 1ST CURTAIN: The flash fires immediately after the shutter
opens (generally the best choice).
• 2ND CURTAIN: The flash fires immediately before the shutter closes.
• AUTO FP(HSS): High-speed sync (compatible units only).
The camera automatically engages front-curtain highspeed sync at shutter speeds faster than the flash sync
speed. Equivalent to 1ST CURTAIN when MULTI is selected
for flash control mode.
G LED light: Choose how the built-in LED light functions during still photography (compatible units only). It can function as a catchlight (CATCHLIGHT), as an AF-assist illuminator
(AF ASSIST), or as both a catchlight and an AF-ASSIST illuminator (AF ASSIST+CATCHLIGHT). Choose OFF to disable the
LED during photography.
G Number of flashes: Choose the number of times the flash
fires each time the shutter is released in MULTI mode. *
H Frequency: Choose the frequency at which the flash fires in
MULTI mode. *
* Full value may not be applied if limits of flash control system are
exceeded.
E Zoom: The angle of illumination (flash coverage) for units
that support flash zoom. Some units allow the adjustment to be made from the camera. If AUTO is selected,
zoom will automatically be adjusted to match coverage
to lens focal length.
EN-4
ENGLISH
Changes and Additions
MASTER (OPTICAL)
The options at right will be
displayed if the unit is currently functioning as master
flash for FUJIFILM optical
wireless remote flash control.
A Flash control mode (group A)/B Flash control mode (group B)/
C Flash control mode (group C): Choose flash control modes
■
MODE
MASTER(OPTICAL)
ADJUST
for groups A, B, and C. TTL% is available for groups A and
B only.
• TTL: The units in the group fire in TTL mode. Flash compensation can be adjusted separately for each group.
• TTL%: If TTL% is selected for either group A or B, you can
specify the output of the selected group as a percentage
of the other and adjust overall flash compensation for
both groups.
• M: In mode M, the units in the group fire at the selected
output (expressed as a fraction of full power) regardless
of subject brightness or camera settings.
• MULTI: Choosing MULTI for any group sets all the units in
all groups to repeating flash mode. All units will fire multiple times with each shot.
• OFF: If OFF is selected, the units in the group will not fire.
END
The master and remote units
can be placed in up to three
C
groups (A, B, and C) and flash
A
mode and flash level adjusted separately for each group.
B
Four channels are available
for communication between
the units; separate channels can be used for different
flash systems or to prevent interference when multiple
systems are operating in close proximity.
D Flash
ENGLISH
compensation/output (group A)/E Flash compensation/
output (group B)/F Flash compensation/output (group C): Adjust flash level for the selected group according to option
selected for flash control mode. Note that the full value
may not be applied if the limits of the flash control system
are exceeded.
• TTL: Adjust flash compensation.
• M/MULTI: Adjust flash output.
• TTL%: Choose the balance between groups A and B and
adjust overall flash compensation.
EN-5
Changes and Additions
G Flash mode (TTL): Choose a flash mode for TTL flash control.
J Lighting: If the unit supports this feature, choose from the
• FLASH AUTO: The flash fires only as required; flash level is
adjusted according to subject brightness. A p icon
displayed when the shutter button is pressed halfway
indicates that the flash will fire when the photo is taken.
• STANDARD: The flash fires with every shot if possible; flash
level is adjusted according to subject brightness. The
flash will not fire if not fully charged when the shutter
is released.
• SLOW SYNC.: Combine the flash with slow shutter speeds
when photographing portrait subjects against a backdrop of night scenery. The flash will not fire if not fully
charged when the shutter is released.
options below.
• FLASH POWER PRIORITY: Gain range by slightly reducing
coverage.
• STANDARD: Match coverage to picture angle.
• EVEN COVERAGE PRIORITY: Slightly increase coverage for
more even lighting.
H Sync: Control flash timing.
• 1ST CURTAIN: The flash fires immediately after the shutter
opens (generally the best choice).
• 2ND CURTAIN: The flash fires immediately before the shutter closes.
• AUTO FP(HSS): High-speed sync (compatible units only).
The camera automatically engages front-curtain highspeed sync at shutter speeds faster than the flash sync
speed. Equivalent to 1ST CURTAIN when MULTI is selected
for flash control mode.
K Master: Assign the master flash to group A (Gr A), B (Gr B),
or C (Gr C). If OFF is selected, output from the master flash
will be held to a level that does not affect the final picture.
Available only if the unit is mounted on the camera hot
shoe as a master flash for FUJIFILM optical wireless remote
flash control in TTL, TTL%, or M mode.
K Number of flashes: Choose the number of times the flash
fires each time the shutter is released in MULTI mode.
L Channel: Choose the channel used by the master flash for
communication with the remote flash units. Separate
channels can be used for different flash systems or to prevent interference when multiple systems are operating in
close proximity.
L Frequency: Choose the frequency at which the flash fires
I Zoom: The angle of illumination (flash coverage) for units
that support flash zoom. Some units allow the adjustment
to be made from the camera. If AUTO is selected, zoom will
automatically be adjusted to match coverage to lens focal
length.
EN-6
ENGLISH
in MULTI mode.
Changes and Additions
RED EYE REMOVAL
Remove red-eye effects caused by the flash.
Option
FLASH +
REMOVAL
FLASH
REMOVAL
OFF
Description
A red-eye reduction pre-flash is combined with
digital red-eye removal.
Flash red-eye reduction only.
Digital red-eye removal only.
Flash red-eye reduction and digital red-eye
removal off.
R Flash red-eye reduction is not available in TTL flash control
mode or while TTL lock is in effect. Digital red-eye removal
is performed only when a face is detected and is not available with RAW images.
TTL-LOCK MODE
Instead of adjusting flash level with each shot, TTL flash
control can be locked for consistent results across a series of photographs.
Option
Description
The value metered for the most recent photo
LOCK WITH LAST taken using TTL will be used for subsequent
FLASH
photos. An error message will be displayed if
no previously metered value exists.
LOCK WITH
The value metered with the next series of preMETERING FLASH flashes will be used for subsequent photos.
R To use TTL lock, assign TTL-LOCK to a camera control and
then use the control to enable or disable TTL lock.
R Flash compensation can be adjusted while TTL lock is in
effect. TTL lock can not be combined with flash red-eye
reduction.
ENGLISH
EN-7
Changes and Additions
LED LIGHT SETTING
Choose whether to use the flash unit’s LED video light
(if available) as a catchlight or AF-assist illuminator
when taking photos.
Option
CATCHLIGHT
AF ASSIST
AF ASSIST +
CATCHLIGHT
OFF
Role of LED video light in still photography
Catchlight
AF-assist illuminator
MASTER SETTING
Choose a flash group (A, B, or C) for the flash mounted
on the camera hot shoe when it functions as a master
flash controlling remote flash units via FUJIFILM wireless optical flash control, or choose OFF to limit master flash output to a level that does not affect the final
picture.
AF-assist illuminator and catchlight
Options: Gr A, Gr B, Gr C, OFF
None
R This option can also be accessed via the flash settings
menu.
R This option can also be accessed via the flash settings
menu.
CH SETTING
Choose the channel used for communication between
the master flash and remote flash units when using
FUJIFILM optical wireless flash control. Separate channels can be used for different flash systems or to prevent interference when multiple systems are operating
in close proximity.
Options: CH1, CH2, CH3, CH4
EN-8
ENGLISH
Changes and Additions
Editing the Quick Menu
Assigning Roles to the Function Buttons
X-Pro2 Owner’s Manual: P 49, 112
The items that can be assigned to the quick menu
have changed.
• SELECT CUSTOM SETTING *
• FACE/EYE DETECTION SETTING
• PHOTOMETRY
• DYNAMIC RANGE *
• WHITE BALANCE *
• AF MODE
• FLASH FUNCTION SETTING
• NOISE REDUCTION *
• IMAGE SIZE
• FLASH COMPENSATION
• MF ASSIST
• IMAGE QUALITY
• FILM SIMULATION *
• MOVIE MODE
• MIC LEVEL ADJUSTMENT
• GRAIN EFFECT *
• EVF/LCD BRIGHTNESS
• HIGHLIGHT TONE *
• SHADOW TONE *
• EVF/LCD COLOR
• COLOR *
• SHUTTER TYPE
• NONE
• SHARPNESS *
• SELF-TIMER
* Stored in custom settings bank.
X-Pro2 Owner’s Manual: P 51, 112
The roles that can be assigned to the function buttons have changed.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PREVIEW DEPTH OF FIELD
ISO AUTO SETTING
SELF-TIMER
IMAGE SIZE
IMAGE QUALITY
DYNAMIC RANGE
FILM SIMULATION
GRAIN EFFECT
WHITE BALANCE
PHOTOMETRY
AF MODE
FOCUS AREA
FLASH FUNCTION SETTING
TTL-LOCK
•
•
•
•
•
•
•
•
•
•
•
•
•
MODELING FLASH
SELECT CUSTOM SETTING
MOVIE
FACE/EYE DETECTION SETTING
RAW
APERTURE SETTING
WIRELESS COMMUNICATION
SHUTTER TYPE
PREVIEW EXP./WB IN MANUAL MODE
PREVIEW PIC. EFFECT
BRIGHT FRAME SIMULATOR
BRIGHT FRAME BRIGHTNESS
NONE
TTL-LOCK
If TTL-LOCK is selected, you can press the control to
lock flash output according to the option selected for
F FLASH SETTING > TTL-LOCK MODE (EN-7).
■
MODELING FLASH
If MODELING FLASH is selected, you can press the
control to test-fire the flash (modeling flash).
■
ENGLISH
EN-9
Changes and Additions
Auto Power Save
X-Pro2 Owner’s Manual: P 114
A AUTO POWER SAVE option has been added to the D POWER MANAGEMENT item in the setup menu.
AUTO POWER SAVE
A power-saving option has been added for the LCD/EVF displays.
Option
ON
OFF
EN-10
Description
When HIGH PERFORMANCE or STANDARD is selected for D POWER MANAGEMENT > PERFORMANCE, the
LCD and EVF will switch to a standard-quality display if no operations are performed for a set period. Operating
camera controls restores the high-quality display.
Display quality does not change when no operations are performed.
ENGLISH
Changes and Additions
Corrected AF Frame
X-Pro2 Owner’s Manual: P 94
The display when OFF is selected for G AF/MF SETTING > CORRECTED AF FRAME in the shooting menu has
changed so that the active focus frame is displayed in green when the shutter button is pressed halfway.
CORRECTED AF FRAME
ON
Focus frame for focus distance of infinity
Focus frame
OFF
Focus frame for focus distance of infinity
Active focus frame (displayed
in green when shutter button
is pressed halfway)
Focus frame for focus distance of about 50 cm (1.6 ft)
ENGLISH
Active focus frame
(displayed in green when shutter button is pressed halfway)
EN-11
Memo
Memo
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising