ToshibaBT 4.x manual_060719

ToshibaBT 4.x manual_060719
4.0
USB Adapter
Manual and
Application note
Index
INTRODUCTION
1
CHAPTER 1
Supported profiles
Supported languages
Supported operating systems
Limitations
2
3
3
3
CHAPTER 2
Setup for Windows 2000/XP
CHAPTER 3
Basic setting
Express Mode Set-up
Custom Mode Set-up
5
9
9
16
CHAPTER 4
Making the most of your Bluetooth
device
24
Connecting to the internet
24
Connecting to the internet using a modem
station
24
Connecting to the internet using a mobile
telephone
33
Connecting to a network[LAN]
42
Connecting to a LAN using an access
point[LAP]
42
Connecting to a LAN using an access
point[PAN]
51
Sending Files
57
Exchanging Files with a PC or PDA
57
Sending images to a mobile telephone
63
Exchanging business card data with a PC
or PDA
66
Synchronizing data with a PDA
76
Connecting using ActiveSync
76
Fax transmission
86
Using a modem station for fax
transmission
86
Using a mobile telephone for fax
transmission
106
Using a Bluetooth-compatible camera 120
Using a headset communicate
125
CHAPTER 5
Advanced features
Making an undiscoverable to other
users
133
133
Encrypting the content of your
transmissions
134
Changing the default connection
135
Manually creating a virtual Bluetooth COM
port
137
CHAPTER 6
Troubleshooting
General operating of the Bluetooth
Utility
Using a wireless modem station
Using an access point
Using a mobile telephone
Using a PDA
Using a camera
Using a Bluetooth Headset
FCC Caution
142
142
145
148
149
152
153
153
155
i
Introduction
Bluetooth is an open specification for a cutting-edge technology that enables short-range
wireless connections between desktop and laptop computers, personal digital assistants,
cellular phones, printers, scanners, digital cameras and even home appliances — on a
globally available band (2.4GHz) for worldwide compatibility. In a nutshell, Bluetooth
unplugs your digital peripherals and makes cable clutter a thing of the past. Now you can
connect your PDA or PC to Bluetooth™ enabled mobile phone with this Bluetooth™
adapter.
You can access e-mail & Internet no matter where you are with just a little help from your
Bluetooth™ mobile phone.
Plus, when you are back in the office, you can hook yourself up to your office network as
well as communicate with other Bluetooth™-enabled devices.
1
1
Chapter1
Supported profiles
(a) Dial-Up Network (DUN)
(b) Fax profile (FAX)
(c) Local Access Profile (LAP)
(d) Serial Port Profile (SPP)
(e) Human Interface Devices (HID)
(f) Hard Copy Replacement Profile (HCRP)
(g) File Transfer Profile (FTP)
(h) Object Push Profile (OPP)
(i) Headset Profile (HSP)
(j) Personal Area Network (PAN)
(k) Basic Imaging Profile (BIP)
(l) Advanced Audio Distribution Profile (A2DP)
(m) A/V Remote Control Profile (AVRCP)
(n) Generic Audio Video Distribution Profile (GAVDP)
2
Supported languages
The Bluetooth Stack for Windows supports the following languages.
English
Danish
French
German
Italian
Japanese
Norwegian
Spanish
Swedish
Dutch
Korean
Simplified Chinese
Traditional Chinese
Russian
Finnish
Portuguese (Brazil)
Supported operating systems
The Bluetooth Stack for Windows supports the following operating systems.
Windows 2000 Professional (Service Pack 3 or above)
Windows XP Professional (Service Pack 1 or above)
Windows XP Home (Service Pack 1 or above)
Windows XP Tablet PC Edition
Windows XP Media Center Edition
Windows XP (64bit)
Limitations
(a) External Bluetooth drivers cannot be "signed drivers" to receive Microsoft WHQL logo.
Therefore, Microsoft's "Unsigned driver" warning messages may pop up during the
software installation, Bluetooth headset, mouse or keyboard setup. Please install the
drivers and then follow the on-screen instructions.
(b) On Swedish Windows XP, an error message (error code = 633) may be seen during
dial-up. Please update the operating system to Windows XP Service Pack 2 or refer to
Microsoft knowledge base #831717.
(c) Windows XP fast user switch is not supported. When switching to another user, the
Bluetooth Manager is not launched. Please log off before switching to another user.
3
(d) If "automatic FAX receiving" is enabled on Microsoft FAX manager, and if DUN, FAX,
or LAP profile icon is registered on Bluetooth Settings, and then Bluetooth's "resume from
standby" may take a couple of minutes to turn on.
(e) Before connecting or disconnecting a Bluetooth headset, please exit any voice or
sound-related applications (e.g. Windows Messenger, Windows Media Player). The
audio input and output may not be switched properly if those applications are running.
This same precaution is important prior to system standby, hibernate or shutdown, and
prior to turning off or unpluging the primary Bluetooth device.
4
2
Chapter2
Setup for Windows 2000/XP
Installing Bluetooth software for Windows
1. Please insert the accompanying CD and the setup menu should launch
automatically. If the setup menu does not launch automatically, use Windows
Explorer to navigate to the appropriate CD-ROM drive and run "setup".
Please select the type of your O/S to start the installation.
2.
Please choose the setup language that you want to install.
5
3.
Please click “NEXT” button to start the installation
3. When the License Agreement screen is displayed, read the License Agreement,
then click the radio button to the left of "I accept the terms in the license
agreement" and then click the “Next“ button.
6
4.
Please click “install” to begin the installation.
5.
Please click “I accept “ to install the Toshiba stack without showing warnings for
unauthorized drivers from Microsoft.
7
6. During the installation, the system will try to detect your Bluetooth device, please plug
in your Bluetooth device and then click on the “OK” button.
7.
Please click “Finish” to complete the installation.
8.
You may need to restart for made the software to effect.
.
8
3
Chapter 3
Basic setting
Methods for registering new devices using the Bluetooth Utility shall now be described.
A Bluetooth mouse shall be connected and set up using [Bluetooth Settings] as an
example.
[Bluetooth Settings] provides two set-up methods: "Express Mode" and "Custom Mode."
•
Express Mode
[Bluetooth Settings] will automatically detect and register services. If several
services (profiles) are supported by the device the service that has been set to the
highest priority shall be selected and registered.
Express Mode is normally recommended for device set-up.
•
Custom Mode
After having been detected, the services supported by the device are displayed as
a list, from which you can select the desired function(s).
Custom Mode must be used to set up a device if, for example, you wish to use a
modem station to send a fax (because in Express Mode, the DUN profile will be
automatically selected since it has a higher priority than the FAX profile).
The differences between setting up the same device (a Bluetooth mouse) using Express
Mode and Custom Mode are described on the following pages.
3.1 Express Mode Set-up
3.1.1
Starting Bluetooth Settings
1. Click [Start]Æ[All Programs]Æ[Bluetooth]Æ[Bluetooth Settings].
(Under Windows 2000, click [Start]→[Programs]→[Bluetooth]→[Bluetooth
Settings].)
9
Note
The same result can be achieved by right-clicking on the Bluetooth icon in the
task tray and selecting [Bluetooth Settings] from the menu that appears.
The [Add new Connection Wizard ] window below will appear when other
devices have already been registered.
Please click the mode and click “Next” button to detect Bluetooth devices."
3.1.2
Detecting Bluetooth devices
The [Add New Connection Wizard (Welcome to the Add New Connection Wizard)] window
will appear.
10
1. Switch the device power ON to make it connectable via Bluetooth.
2. Confirm that [Express Mode] has been selected in the [Add New Connection
Wizard (Welcome to the Add New Connection Wizard)] window, and click on
the [Next] button.
Searching for Bluetooth devices will start.
11
When the device has been detected, the name and address of the device will
appear in the [Add New Connection Wizard (Select Device)] window.
Note
If no device is found, please confirm that the device has been made connectable
via Bluetooth, and click on the [Update] button.
A further device search will be performed.
12
3.1.3
Detecting services
1. Select the device name from [Device List] and click on the [Next] button.
Bluetooth device detection will commence(See it on next page).
13
Note
●If several services (profiles) are supported by the device, the service that has
been set to the highest priority shall be automatically selected and set up in
Express Mode. Please use Custom Mode if you wish to select desired services
manually.
•When a service has been detected, a window prompting you to enter the
Bluetooth passkey (PIN code) may appear.(for example , pairing a mobile phone
with a PC). Please enter the passkey and click on the [OK] button.
●If you have not entered your Bluetooth passkey after a certain amount of time
has passed, the connection process will be cancelled for security reasons.
Please perform the passkey entry process again.
2. The paired device will showed on the screen of Bluetooth wizard.
14
3.1.4
Registering settings information
The [Add New Connection Wizard (Completing the Add New Connection Wizard)] window
will appear.
1. Click on the [Finish] button
The [Bluetooth Settings] window will appear.
The icons of the registered devices will appear, and the devices will be ready to
use.
15
3.2 Custom Mode Set-up
3.2.1
Starting Bluetooth Settings
1. Click [Start]Æ[All Programs]Æ[Bluetooth]Æ[Bluetooth Settings].
(Under Windows 2000, click [Start]→[Programs]→[Bluetooth]→[Bluetooth
Settings].)
Note
●The same result can be achieved by right-clicking on the Bluetooth icon in the
task tray and selecting [Bluetooth Settings] from the menu that appears.
The [Bluetooth Settings] window below will appear when other devices have
already been registered.
16
Please click the [New Connection] button to open the [Add New Connection Wizard]
window. If no devices have been registered yet, please proceed directly to
"Detecting Bluetooth Devices."
3.2.2
Detecting Bluetooth devices
The [Add New Connection Wizard (Welcome to the Add New Connection Wizard)] window
will appear.
1. Switch the device power ON to make it connectable via Bluetooth.
2. Confirm that [Custom Mode] has been selected in the [Add New Connection
Wizard (Welcome to the Add New Connection Wizard)] window, and click on
the [Next] button.
Searching for Bluetooth devices will start.
17
When the device has been detected, the name and address of the device will
appear in the [Add New Connection Wizard (Select Device)] window.
Note
●If no device is found, please confirm that the device has been made
connectable via Bluetooth, and click on the [Update] button.
●A further device search will be performed.
18
3.2.3
Detecting services
1. Select the device name from [Device List] and click on the [Next] button.
Bluetooth device detection will commence.
19
Note
●When a service has been detected, a window prompting you to enter the
Bluetooth passkey (PIN code) may appear. Please enter the passkey and click
on the [OK] button.
●If you have not entered your Bluetooth passkey after a certain amount of time
has passed, the connection process will be cancelled for security reasons.
Please perform the passkey entry process again.
The services supported by the device will be displayed.
Note
●When a device supports several services
If the device supports several services, you can use Custom Mode to manually
select the services (profiles) you wish to use from the list that appears under
[Select Services].
Example: List of wireless modem station services
If Express Mode is used to perform the set-up, the highest-priority service in the
device will be automatically selected and configured.
20
2. Click on the [OK] button.
The [Add New Connection Wizard (Connection Name Setup)] window will appear if a
service has been properly detected.
3. Select the type and name of the icon to be displayed once the device has
been registered, and click on the [Next] button.
Note
●If you wish to change the icon, please click on the [Change Icon] button and
select your preferred icon from the list that appears.
21
22
3.2.4
Registering settings information
The [Add New Connection Wizard (Completing the Add New Connection Wizard)] window
will appear.
1. Click on the [Finish] button
The [Bluetooth Settings] window will appear.
The icons of the registered devices will appear, and the devices will be ready to
use.
23
4
Chapter 4
Making the most of your Bluetooth device
4.1 Connecting to the internet
4.1.1
Connecting to the internet using a modem station
Setting up the modem station
1. Turn on the wireless modem station.
2. Right-click the Bluetooth icon in the task tray, and then click on [Add New
Connection].
Note
●Alternatively, click [Start]→[All Programs]→[Bluetooth]→[Bluetooth Settings],
and then click on [New Connection] from the active [Bluetooth Settings] window.
3. Confirm that [Express Mode] has been selected, and then click on the [Next]
button.
24
The [Add New Connection Wizard (Searching for Bluetooth devices)] window will
appear.
25
4. Select the device name of the wireless modem station from [Device List], and
then click on the [Next] button.
The [Add New Connection Wizard (Searching for Services)] window will appear.
Once a service has been detected successfully, connection to the device and COM
port creation will be performed automatically, after which the [Add New Connection
Wizard (Modem Settings)] window will appear.
26
5. If you are connecting to a wireless modem station for the first time, enter the
passkey for the modem station under [Bluetooth Passkey (PIN code)], and
then click on the [OK] button.
Once the program has finished searching for the devices, the [Add New
Connection Wizard (Device Selection)] window will appear.
6. Select a service that you want .
7. The below settings will instruct you set the Bluetooth modem by the DUN
(Dial-Up Profile)
8. Enter the connection name (optional), telephone number (of your provider's
access point), user name and password (as issued by your provider), and
then click on the [Finish] button.
27
Important
●The sample entries shown in the window are provided solely for purpose of
explanation. Please use your own telephone number, ID and password
according to the arrangement with your provider.
The settings will be registered, and an icon will appear in the [Bluetooth Settings]
window.
Connecting to the Internet
1. Start your browser, e-mail application or other application
Important
●Please enter the e-mail settings separately if you are going to use e-mail (the
set-up method will vary with the application).
2. Enter the URL of the Web page you wish to display and then press the [Enter]
key, or use the e-mail tool to send/receive items or perform other activities.
The [Dial-up Connection] window will appear.
3. Click on the [Connect] button
28
Important
.A connection will be automatically established with the modem station if COM
Auto Connect is available. If COM Auto Connect is not available, please
manually connect to the modem station.
The following message will appear once you have connected to the Internet.
4. End the connection
The window below will appear if you double-click on the
29
icon in the task bar.
Please click on the [Disconnect] button when you want to disconnect from the Internet.
Alternatively, please right-click on the
icon, and then click on [Disconnect].
Note
.You can start an application to make an automatic connection to the Internet, but
you can also make a manual connection using the connection destination icon.
The procedure is described below.
1. From the [Bluetooth Settings] window, right-click on the connection
destination icon, and then click on [Connect] from the menu that appears.
A window indicating that the connection is being established will appear.
30
If the connection has been established successfully, the connection icon and task
tray will appear as shown below.
You will be able to browse Web pages using your browser and send and receive
e-mail.
Important
.Please enter the e-mail settings separately if you are going to use e-mail (the
set-up method will vary with the application).
2. End the connection
Right-click on the icon, and then click [Disconnect] to end the connection.
31
The following message will appear. Click on the [Yes] button.
When the icon appears as shown below, the connection will have ended.
32
4.1.2
Connecting to the internet using a mobile telephone
Important
.In order to connect to the Internet, you must have already signed up with a
provider and obtained a connection ID and password. Please ensure you have
confirmed the ID, password and telephone number of your provider's access
point before you begin the set-up process.
.A Bluetooth passkey (PIN code) is required for you to connect to the mobile
telephone. Please make a note of your Bluetooth passkey before you start the
set-up process.
Configuring a mobile telephone for use a modem
1. Turn on the mobile phone, and set it to be connectable via Bluetooth.
2. Right-click the Bluetooth icon in the task tray, and then click on [Add New
Connection].
Note
.Alternatively, click [Start]→[All Programs]→[Bluetooth]→[Bluetooth Settings],
and then click on [New Connection] from the active [Bluetooth Settings] window.
3. Confirm that [Express Mode] has been selected, and then click on the [Next]
button.
33
The [Add New Connection Wizard (Searching for Bluetooth devices)] window will
appear.
4. Select the device name of the mobile telephone from [Device List], and then
click on the [Next] button.
34
The [Add New Connection Wizard (Searching for Services)] window will appear.
Once a service has been detected successfully, connection to the device and COM
port creation will be performed automatically, after which the [Add New Connection
Wizard (Modem Settings)] window will appear.
5. If you are connecting to a mobile telephone for the first time, enter the
passkey for the wireless modem station under [Bluetooth Passkey (PIN
code)], and then click on the [OK] button.
35
Once the program has finished searching for the devices, the [Add New
Connection Wizard (Device Selection)] window will appear.
6. Click on the [Next] button.
Certain modems require you to configure initialization commands separately.
Please click on the [Additional initialization Command Settings] button, enter the
initialization commands in the following window, and then click on the [OK]
button.
36
7. Enter the connection name (optional), telephone number (of your provider's
access point), user name and password (as issued by your provider), and
then click on the [Finish] button.
Important
.The sample entries shown in the window are provided solely for purpose of
explanation. Please use your own telephone number, ID and password
according to the arrangement with your provider.
The settings will be registered, and an icon will appear in the [Bluetooth Settings]
window.
37
Connecting to the Internet
1. Start your browser, e-mail application or other application
Important
.Please enter the e-mail settings separately if you are going to use e-mail (the
set-up method will vary with the application).
2. Enter the URL of the Web page you wish to display and then press the [Enter]
key, or use the e-mail tool to send/receive items or perform other activities.
The [Dial-up Connection] window will appear.
3. Click on the [Connect] button
Important
.A connection will be automatically established with the modem station if COM
Auto Connect is available. If COM Auto Connect is not available, please
manually connect to the mobile telephone .
The following message will appear once you have connected to the Internet.
38
4. End the connection
The window below will appear if you double-click on the
icon in the task bar.
Please click on the [Disconnect] button when you want to disconnect from the Internet.
Alternatively, please right-click on the
icon, and then click on [Disconnect].
Note
.You can start an application to make an automatic connection to the Internet, but
you can also make a manual connection using the connection destination icon.
The procedure is described below.
1. From the [Bluetooth Settings] window, right-click on the connection
destination icon, and then click on [Connect] from the menu that appears.
39
A window indicating that the connection is being established will appear.
If the connection has been established successfully, the connection icon and task
tray will appear as shown below.
You will be able to browse Web pages using your browser and send and receive
e-mail.
40
Important
.Please enter the e-mail settings separately if you are going to use e-mail (the
set-up method will vary with the application).
2. End the connection
Right-click on the icon, and then click [Disconnect] to end the connection.
The following message will appear. Click on the [Yes] button.
When the icon appears as shown below, the connection will have ended.
41
4.2 Connecting to a network[LAN]
4.2.1
Connecting to a LAN using an access point[LAP]
Setting up the access point
Important
.The access point must have been started and a normal connection already
established to the network before the access point is set up. Please refer to the
access point instruction manual for information on how to set up the access
point.
.A Bluetooth passkey (PIN code) is required for you to connect to the access
point. Please make a note of your Bluetooth passkey before you start the set-up
process.
1. Turn on the access point, and confirm that a connection has been
established with the network.
2. Right-click the Bluetooth icon in the task tray, and then click on [Add New
Connection].
Note
.Alternatively, click [Start]→[All Programs]→[Bluetooth]→[Bluetooth Settings],
and then click on [New Connection] from the active [Bluetooth Settings] window.
3. Confirm that [Express Mode] has been selected, and then click on the [Next]
button.
42
The [Add New Connection Wizard (Searching for Bluetooth devices)] window will
appear.
4. Select the device name of the access point from [Device List], and then click
on the [Next] button.
43
You will be asked for the Bluetooth passkey in the window that appears.
5.
Then the icon will create as below
6.
Double click on the icon, and enter the passkey under [Bluetooth Passkey
(PIN code)], and then click on the [OK] button.
44
Service detection and COM port creation will be performed automatically.
The [Add New Connection Wizard (Create Connection Destination)] window will
appear.
7.
Enter the connection name, user name and password, then click on the
[Next] button.
Note
.The user name and password are entered here to allow you to connect to the
access point.
The [Add New Connection Wizard (Confirm Dial-up Settings)] window will appear.
8.
Click on the [Confirm Settings] button.
45
9.
Configure the connection method, and then click on the [OK] button.
Set the connection destination used for the LAN connection set up in (6) above as
the default connection destination, and then select "Always dial my default
connection."
46
10. Click on the [Next] button.
11. Enter the type and name of the icon displayed after registration, and then
click on the [Next] button.
Please click on the [Next] button if you are satisfied with the settings.
47
12. Click on the [Finish] button.
The access point icon will be registered in the [Bluetooth Settings] window.
Connecting to a LAN(LAP)
1. Right-click on the connection icon in the [Bluetooth Settings] window, and
then click on [Connect].
2. Confirm that "Direct connection" has been selected under [Connection
Destination], and then click on the [Connect] button
48
A connection will be initiated.
Note
.This is an example of what happens when you use "Direct connection" as a
connection name under "Connect to access point." If a name different from the
connection name is used, that name will appear under [Connection
Destination].
.Please simply click on [Settings] if no user name or password have been
entered (i.e., if those fields have been left blank)
.Please change the connection destination if a different connection name (for a
dial-up connection) appears in [Connection Destination].
Once you connect to the network, Internet Explorer will start automatically, and you
will be able to exchange data with other computers on the network.
Note
.Please follow the procedure below if you need to set up a proxy server to
connect to the Internet (the following procedure is not necessary if the PC you
are going to use has already been set up as a proxy server).
1. Select [Internet Options...] from the [Tools] menu in Internet Explorer.
The [Internet Options] window will appear.
2. Click on the [Connections] tab, and then click on the [Settings...]
button.
49
3. Enter the IP address and port number of the proxy server under [Proxy
Server], and then click on the [OK] button.
50
4.2.2
Connecting to a LAN using an access point[PAN]
Setting up the access point
Important
.The access point must have been started and a normal connection already
established to the network before the access point is set up. Please refer to the
access point instruction manual for information on how to set up the access
point.
.A Bluetooth passkey (PIN code) is required for you to connect to the access
point. Please make a note of your Bluetooth passkey before you start the set-up
process.
2. Turn on the access point, and confirm that a connection has been
established with the network.
3.
Right-click the Bluetooth icon in the task tray, and then click on [Add New
Connection].
Note
.Alternatively, click [Start]→[All Programs]→[Bluetooth]→[Bluetooth Settings],
and then click on [New Connection] from the active [Bluetooth Settings] window.
4.
Confirm that [Express Mode] has been selected, and then click on the [Next]
button.
51
The [Add New Connection Wizard (Searching for Bluetooth devices)] window will
appear.
5.
Select the device name of the access point from [Device List], and then click
on the [Next] button.
52
You will be asked for the Bluetooth passkey in the window that appears.
6.
Enter the passkey under [Bluetooth Passkey (PIN code)], and then click on
the [OK] button.
Service detection and COM port creation will be performed automatically.
The [Add New Connection Wizard (Connection Name Settings)] window will
appear.
7.
Enter the type and name of the icon displayed after registration, and then
click on the [Next] button.
Please click on the [Next] button if you are satisfied with the settings.
53
The [Add New Connection Wizard (Completing the Add New Connection Wizard)]
window will appear.
8.
Click on the [Finish] button.
The access point icon will be registered in the [Bluetooth Settings] window.
This will complete the access point set-up process.
Connecting to a LAN(PAN)
1. Right-click on the connection icon in the [Bluetooth Settings] window, and
then click on [Connect].
54
2. Enter the passkey under [Bluetooth Passkey (PIN code)], and then click on
the [OK] button.
A connection will be initiated.
Note
.Please follow the procedure below if you need to set up a proxy server to
connect to the Internet (the following procedure is not necessary if the PC you
are going to use has already been set up as a proxy server).
1. Select [Internet Options...] from the [Tools] menu in Internet Explorer.
The [Internet Options] window will appear.
2. Click on the [Connections] tab, and then click on the [Settings...]
button.
55
3. Enter the IP address and port number of the proxy server under [Proxy
Server], and then click on the [OK] button.
56
4.3 Sending files
You can send and receive files other than business card data with a Bluetooth-enabled
PC or PDA.
Use "File transfer" in the Bluetooth Information Exchanger to exchange files.
Note
.The same operations will be valid as long as the PC and PDA support the FTP
profile
."File transfer" cannot be used to send or receive business card data. Please
instead use "Object Push" to perform these activities.
4.3.1 Exchanging files with a PC or PDA
Sending files to a PC or PDA
1. Turn on the PC or PDA.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop.
Note
.Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
57
3. Double-click on the [File transfer] icon.
A list of devices will appear in the [File transfer] window.
Note
.If the desired device does not appear in the list, please confirm that the device
has been turned on, and then select [Bluetooth]→[Search Devices].
A device search will be performed.
.You can also use "Image transfer" when sending individual image files.
4. Use the mouse to drag and drop the file you wish to send over the destination
icon.
In this case, the file will be sent to a PC named "PC-1".
58
Note
.When using "File transfer", you can send individual files as well as entire
folders.
5. Confirm that the file is being sent.
The file will be sent to the PC.
Note
.When sending files using "File transfer", a message requesting permission to
receive the files may appear on the destination (receiving) device. The content of
the message will vary with the Bluetooth software installed on the destination
device, so please be sure to follow the instructions provided.
If you are using the Bluetooth Utility, a message similar to the one below will
appear.
If the file has been sent successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the file transmission was unsuccessful.
Please click on the [OK] button to close the message, and repeat the procedure.
Note
.Files that have been sent will be saved in a file transfer shared folder on the
destination device.
59
.Additionally, with "File transfer", you can open the shared folder on the
destination device using Explorer, specify a subfolder, and then send the file
there.
.You can use Properties in the Bluetooth Information Exchanger to change the
location of the "Shared folder" on the hard drive.
Receiving files from a PC or PDA
Your PC is able to receive files that have been saved in the shared folder on the
destination PC or PDA. Received files will be saved in the shared folder under "File
transfer".
1. Turn on the PC or PDA.
Confirm that a Bluetooth connection has been enabled before proceeding.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop.
Note
.Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
60
3. Double-click on the [File transfer] icon
A list of devices will appear in the [File transfer] window.
In this case, the file will be received from the PDA named "My Mobile".
4. Double-click on the [PDA-1] icon
The file saved in the shared folder in "My Mobile" will appear.
5. Right-click on the file you wish to receive, and then select "Receive file".
61
The file will be received from a PDA.
Note
.With "File transfer", you can send individual files as well as entire folders.
Please right-click on the folder you wish to receive, and select "Receive folder".
Subsequent operations should be performed in the same manner as when
receiving individual files.
If the file has been received successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the file transmission was unsuccessful. Please
click on the [OK] button to close the message, and repeat the procedure.
62
Note
.The received file will be saved in the "Shared folder" under "File transfer" in the
Bluetooth Information Exchanger
You can use Properties under the Bluetooth Information Exchanger to specify
the location of the "Shared folder" on the hard drive.
4.3.2 Sending images to a mobile telephone
1. Turn on the PC or PDA.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop.
Note
.The mobile telephone must support the BIP profile.
.The image file”(*.bmp)(*.jpg,*.jpeg)(*.png)” formats can be sent and received
using "Image transfer".
.Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
63
3. Double-click on the [File transfer] icon.
A list of devices will appear in the [File transfer] window.
4. Drag and drop the file you wish to send over the destination icon.
In this case, the image will be sent to a mobile telephone named "BT-Phone-1".
64
The image will be sent.
If the image has been sent successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the image transmission was unsuccessful.
Please click on the [OK] button to close the message, and repeat the procedure.
65
4.4 Exchanging business card data with a PC or PDA
You can exchange business card data with a Bluetooth-enabled PC or PDA.
Business card data are exchanged using "Object Push" under Bluetooth Information
Exchanger.
Selecting a business card and sending it to a PC or PDA
1. Turn on the PC or PDA.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop.
Note
.Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
3. Double-click on the [Object Push] icon.
A list of devices will appear in the [Object Push] window.
66
Note
.If the desired device does not appear in the list, please confirm that the device
has been turned on, and then select [Bluetooth]→[Search Devices].
A device search will be performed.
4. Use the mouse to drag and drop the business card you wish to send over the
destination icon
In this case, the business card will be sent to a PC named "PC-1".
Note
.When you try to send a business card, a message requesting permission to
receive the card may appear on the device belonging to the other party (i.e., on
the receiving end). The content of the message will vary with the Bluetooth
software installed on the destination device, so please be sure to follow the
instructions provided. If you are using the Bluetooth Utility, a message similar to
the one below will appear.
67
If the business card has been sent successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the business card transmission was
unsuccessful.
Please click on the [OK] button to close the message, and repeat the procedure.
Selecting your personal business card
You can prepare a business card bearing your name and other details such as your
company and telephone numbers, and then send it to another party.
Note
.Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
1. Turn on the PC or PDA.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop.
68
Note
.Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
3. Double-click on the [Object Push] icon.
A list of devices will appear in the [Object Push] window.
Note
.If the desired device does not appear in the list, please confirm that the device
has been turned on, and then select [Bluetooth]→[Search Devices].
A device search will be performed.
69
4. Right-click on the destination icon, and then click on [Send business card
To].
In this case, your personal business card will be sent to a PC named "PC-1".
The business card will be sent.
Note
.When you try to send a business card, a message requesting permission to
receive the files may appear on the device belonging to the other party (i.e., on
the receiving end). The content of the message will vary with the Bluetooth
software installed on the destination device, so please be sure to follow the
instructions provided. If you are using the Bluetooth Utility, a message similar to
the one below will appear.
.Business cards that have been sent will be saved in the Inbox of the destination
party.
If your business card has been sent successfully, the message below will appear.
Please click on the [OK] button.
70
The message below will appear if the business card transmission was unsuccessful.
Please click on the [OK] button to close the message, and repeat the procedure.
Note
.Data that has been sent will be saved in a folder for exchanged business cards
on the destination device.
Receiving a business card from another party
You can prepare a business card bearing your name and other details such as your
company and telephone numbers, and then send it to another party.
Note
.Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
1. Turn on the PC or PDA.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop.
Note
.Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
71
3. Double-click on the [Object Push] icon.
A list of devices will appear in the [Object Push] window.
Note
.If the desired device does not appear in the list, please confirm that the device
has been turned on, and then select [Bluetooth]→[Search Devices].
A device search will be performed.
4. Right-click on the icon of the party whose card you wish to acquire, and then
click on [Receive business card]
In this case, the business card of the other party will be acquired from a PC named
"PC-1".
72
The business card will be received.
Exchanging business cards
Simultaneously exchange your business card with one belonging to another party.
1. Turn on the PC or PDA.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop.
Note
.Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
73
3. Double-click on the [Object Push] icon.
A list of devices will appear in the [Object Push] window.
Note
.If the desired device does not appear in the list, please confirm that the device
has been turned on, and then select [Bluetooth]→[Search Devices].
A device search will be performed.
4. Right-click on the icon of the party with whom you wish to exchange
business cards, and then click on [Object Push].
In this case, the business cards will be exchanged with a PC named "PC-1".
74
The business card from the party who executed the "Exchange business cards"
command will be sent first.
Note
.When you try to send a business card, a message requesting permission to
receive the files may appear on the device belonging to the other party (i.e., on the
receiving end). The content of the message will vary with the Bluetooth software
installed on the destination device, so please be sure to follow the instructions
provided.
If you are using the Bluetooth Utility, a message similar to the one below will
appear.
75
4.5 Synchronizing data with a PDA
When you connect via Bluetooth instead of with a standard cable, you will always be able
to synchronize your data without the hassle of having to connect the cable.
4.5.1
Connecting using ActiveSync
Preparing the PC
1. On the PC, click on [Start]Æ[All Programs]Æ[Microsoft ActiveSync].
The initial ActiveSync set-up window will appear.
It is assumed in the explanation below that no ActiveSync connections have been
established with other devices.
2. Click [File]Æ[Connection Settings].
76
The [Connection Settings] window will appear.
3. Place a check next to [Allow serial cable or infrared connection to this COM
port], and then select "COM7".
Note
.In the standard set-up, the port is configured to "COM7" (refer to Steps (3) and
(4) under "Preparing the PDA" below). When using a different port, please also
change the port number selected in this window
Preparing the PDA
1. Tap on the Bluetooth icon in the bottom right of the screen.
77
Important
.The graphic above shows an example of a PDA operating window.
The connection procedure may be different depending on the manufacturer or
model of PDA you use. Please refer to the product instruction manuals for further
details.
The [Bluetooth Settings] window will open.
The message "Connection not registered" will appear if no Bluetooth device has
been registered.
Please tap on [OK] to close the message.
2. Double click on [Tools]Æ[Search for peripheral components].
78
The application searches for nearby Bluetooth devices.
3. Tap and hold on the destination PC icon, and then select [Update Services].
A search for services will be carried out, and then a list of service names and their
connection status will appear as list in the lower window.
79
4. Tap and hold on "COM7" from the list of service names, and then select
"Register ActiveSync".
5. Tap [OK] in the confirmation message window.
80
An ActiveSync connection will be initiated.
Establishing a partnership between ActiveSync and a PDA
Once a connection has been successfully established with a PDA, the procedure for
establishing a partnership with the PDA will be started by the ActiveSync application on
the PC.
Performing this set-up procedure will enable data to be synchronised between your PC
and PDA.
1. In the [New Partnership (Set Up a Partnership)] window, select "Standard
partnership", and then click on the [Next] button.
81
The [New Partnership (Specify Data Synchronisation Method)] window will appear.
2. Select "Synchronise with this PC", and then click on the [Next] button.
The [New Partnership (Select Synchronisation Settings)] window will appear.
3. Select the type of information to be synchronised between your PC and PDA,
and then click on the [Next] button.
The [New Partnership (Completing Setup)] window will appear.
4. Click on the [Finish] button.
82
When you click on the [Finish] button, ActiveSync will begin to synchronize your
information.
[Confirming changes]
↓
(Synchronization process)
↓
[Synchronization complete]
83
While the ActiveSync connection is active, synchronization will be performed
whenever information is changed on either the PC or the PDA.
Once a partnership has been established, every time you start your PC (and PDA)
thereafter, a Bluetooth connection will be opened and ActiveSync will synchronize
your information.
Finishing an ActiveSync connection
Tap and hold on "COM7" in the Bluetooth Settings window, and select
[ActiveSync Release].
Cancelling a partnership
84
Click on [File]Æ"Delete partnership".
Click on the [Yes] button when the confirmation message appears.
85
4.6 Fax transmission
4.6.1
Using a modem station for fax transmission
Important
.Please refer to the modem station instruction manual for information on how to
connect the station to a telephone line.
.Please ensure that any drivers used to connect the PC to the modem have
been installed.
.A Bluetooth passkey (PIN code) is required for you to connect to the modem
station. Please make a note of your Bluetooth passkey before you start the
set-up process.
.A fax application is required for you to be able to send and receive faxes. The
description below is based on a example using Microsoft Fax, which is installed
with Windows XP as standard.
If you are going to use a commercially available fax application, then please refer
to the manual that came with the application for information on how to send and
receive faxes.
Setting up the modem station
1. Turn on the wireless modem station.
2. Right-click on the Bluetooth icon in the task tray, and then click on [Add New
Connection].
Note
.Alternatively, click [Start]→[All Programs]→[Bluetooth]→[Bluetooth Settings],
and then click on [New Connection] from the active [Bluetooth Settings] window.
The [Add New Connection Wizard (Welcome to the Add New Connection
Wizard)] window will appear.
3. Select [Custom Mode], and then click on the [Next] button.
86
The [Add New Connection Wizard (Searching for Bluetooth devices)] window will
appear.
Once the program has finished searching for the devices, the [Add New
Connection Wizard (Select Device)] window will appear.
4. Select the device name of the wireless modem station from [Device List], and
then click on the [Next] button.
87
The [Add New Connection Wizard (Searching for Services)] window will appear.
5. If you are connecting to the wireless modem station for the first time, enter
the passkey for the device from the [Bluetooth Passkey (PIN Code)] window,
and then click on the [OK] button.
88
Once the program has finished searching for the services, the [Add New
Connection Wizard (Select Service)] window will appear.
6. Select "Fax" under [Select Service], and then click on the [Next] button.
The [Add New Connection Wizard (Select COM Port)] window will appear.
7. Check [Use default COM port], and then click on the [Next] button.
89
Note
.The modem station will be installed to the grayed-out COM port displayed under
[Assignment of COM Port] in this window. You will be specifying this COM port in
Step (3) of "●Installing a Modem", so please write it down for future reference.
The [Add New Connection Wizard (Connecting to Remote Device)] window will
appear.
The [Add New Connection Wizard (Modem Settings)] and [Phone and Modem
Options] windows will appear.
90
8. Click on the "Add..." button in the [Phone and Modem Options] window.
The [Add New Hardware Wizard (Install New Modem)] window will appear.
Install the modem by following the instructions in the windows that follow.
Installing a modem
The [Add New Hardware Wizard (Install New Modem)] window will appear.
1. Check [Don't detect my modem; I will select it from a list], and then click on
the [Next] button.
91
A list of modem manufacturers and models will appear.
2. Select the desired wireless modem from under [Manufacturer] and [Models],
and then click on the [Next] button.
Note
.If you have not yet installed a modem driver, click on the "Use Device" button to
install one from this window.
.If no modem drivers appear, please select "(Standard Modem Types)" and
"Standard 33600 bps modem."
92
A window will appear where you can specify the port to which you can install the
modem.
3. Select "Selected Port", specify the COM port to which the modem will be
installed, and then click on the [Next] button.
Important
.Please specify the COM port displayed in the window pertaining to Step (7)
under "●Setting up the modem station."
93
4. Click on the [Continue] button.
The wizard will display the following window by design, but you may disregard it
and click on the "Continue" button.
A window will appear indicating that the modem installation is complete.
5. Click on the [Finish] button.
6. Confirm that the configured modem has been added to the list in the [Phone
and Modem Options] window, and then click on the [OK] button.
94
The [Next] button will be enabled on the [Add New Connection Wizard (Modem
Settings)] window.
7. Click on the [Next] button on the [Add New Connection Wizard (Modem
Settings)] window.
The [Add New Connection Wizard (Connection Name Settings)] window will
appear.
95
8. Enter the type and name of the icon displayed after registration, and then
click on the [Next] button.
Please click on the [Next] button if you are satisfied with the settings.
The [Add New Connection Wizard (Completing the Add New Connection Wizard)]
window will appear.
9. Click on the [Finish] button.
The settings will be registered, and the icon will appear in the [Bluetooth Settings]
window.
Setting fax information
Configure send/receive settings and register fax information.
1. Select [Start]Æ[Control Panel], and then double-click on the [Printers and
Other Hardware] icon.
Note
.If the control panel is displayed in "Classic view", and you use Windows 2000,
please start from Step (2).
2. Double-click on the [Printers and Faxes] icon.
The [Printers & Faxes] window will appear.
3. Click on "Install a local fax printer" in the [Printers and Faxes] window.
96
A window showing installed programs will appear, and a Fax icon will have been
created in the [Printers and Faxes] screen.
4. Click on "Send a fax" under "Printer Tasks" on the left side of the window.
If you have not yet configured a fax device, the [Fax Configuration Wizard] window
will appear. In the window you can enter settings pertaining to the sender
(yourself).
97
Note
.If the fax configuration information has already been registered, the [Send Fax
Wizard] window, which can be viewed under "Sending a fax" below, will appear
instead of the [Fax Configuration Wizard] window.
5. Enter the sender information, and click on the [Next] button
Note
.The sender information that you configure here will be automatically appended
as header information when you send a fax.
6. Select a device to be used for fax transmissions, enable the device for
sending or receiving, and then click on the [Next] button
98
Note
.If [Enable Receive] is selected, the device will be on standby for receiving faxes
even if it is not sending or receiving anything, and therefore will be in continuous
connection to the wireless modem (when COM Auto Connect is on).
Please decide whether to select this option based on the desired objective and/or
frequency of transmission.
7. Click on the [Next] button.
It is important that you do not change the transmitter subscriber identification.
8. Click on the [Finish] button.
99
100
Setting fax information
Important
.The Fax service must be enabled for sending in order for you to send a fax.
Please refer to "Using a wireless modem station" under "Troubleshooting" for
how to change the send and receive settings once the service has been
configured.
1. Double-click on the [Fax] icon in the Control Panel.
The [Fax Console] window will appear.
2. In the [Fax Console] window, click [File]→[Send fax].
The [Send Fax Wizard (Starting the Send Fax Wizard)] window will appear.
3. Click on the [Next] button.
101
The [Send Fax Wizard (Recipient Information)] window will appear.
4. Enter the name and fax number of the destination party, and then click on the
[Next] button.
The [Send Fax Wizard (Preparing the Cover Page)] window will appear.
5. Specify the cover page template, subject line, and note (body text), and then
click on the [Next] button.
102
The [Send Fax Wizard (Schedule)] window will appear.
6. If you wish to send the fax immediately, select "Now", and then click on the
[Next] button.
The [Send Fax Wizard (Completing the Send Fax Wizard)] window will appear.
7. Confirm the destination information and transmission details, and then click
on the [Finish] button.
103
The software will automatically dial the number and send the fax.
Once the fax has been sent, Fax Monitor will revert to standby mode.
Receiving a fax
1. When a fax arrives, the Fax Monitor will start automatically as the fax is
received.
104
Once the fax has been received, the Fax Monitor will revert to standby mode.
Note
.If you have enabled manual fax reception, the message below will appear when
a fax arrives.
Click on the message with your mouse to receive the fax.
2. Double-click on the [Fax] icon in the Control Panel.
The [Fax Console] window will appear.
3. In the [Fax Console] window, double-click on the fax that has arrived.
105
4.6.2
Using a mobile telephone for fax transmission
Important
.Please ensure that any drivers used to connect the PC to the mobile telephone
have been installed.
.Bluetooth passkey (PIN code) is required for you to connect to the mobile
telephone. Please make a note of your Bluetooth passkey before you start the
set-up process.
.A fax application is required for you to be able to send and receive faxes. The
description below is based on a example using Microsoft Fax, which is installed
with Windows XP as standard.
Setting up the mobile telephone
1. Turn on the mobile telephone, and set it to be connectable via Bluetooth.
2. Right-click on the Bluetooth icon in the task tray, and then click on [Add New
Connection].
Note
.Alternatively, click [Start]→[All Programs]→[Bluetooth]→[Bluetooth Settings],
and then click on [New Connection] from the active [Bluetooth Settings] window.
The [Add New Connection Wizard (Welcome to the Add New Connection
Wizard)] window will appear.
3. Select [Custom Mode], and then click on the [Next] button.
106
The [Add New Connection Wizard (Searching for Bluetooth devices)] window will
appear.
Once the program has finished searching for the devices, the [Add New
Connection Wizard (Select Device)] window will appear.
4. Select the device name of the mobile telephone from [Device List], and then
click on the [Next] button.
107
The [Add New Connection Wizard (Searching for Services)] window will appear.
5. If you are connecting to the mobile telephone for the first time, enter the
passkey for the device from the [Bluetooth Passkey (PIN Code)] window, and
then click on the [OK] button.
108
Once the program has finished searching for the services, the [Add New
Connection Wizard (Select Service)] window will appear.
6. Select "Fax" under [Select Service], and then click on the [Next] button.
The [Add New Connection Wizard (Select COM Port)] window will appear.
7. Check [Use default COM port], and then click on the [Next] button.
109
Note
.The mobile telephone will be installed to the grayed-out COM port displayed
under [Assignment of COM Port] in this window. You will be specifying this COM
port in Step (3) of "●Installing a Modem", so please write it down for future
reference.
The [Add New Connection Wizard (Connecting to Remote Device)] window will
appear.
The [Add New Connection Wizard (Modem Settings)] and [Phone and Modem
Options] windows will appear.
110
8. Click on the "Add..." button in the [Phone and Modem Options] window.
The [Add New Hardware Wizard (Install New Modem)] window will appear.
Install the modem by following the instructions in the windows that follow.
Installing a modem
The [Add New Hardware Wizard (Install New Modem)] window will appear.
1. Check [Don't detect my modem; I will select it from a list], and then click on
the [Next] button.
111
A list of modem manufacturers and models will appear.
2. Select the desired mobile telephone from under [Manufacturer] and [Models],
and then click on the [Next] button.
Note
.If you have not yet installed a mobile telephone driver, click on the "Use Device"
button to install one from this window.
.If no mobile telephone drivers appear, please select "(Standard Modem Types)"
and "Standard 33600 bps modem."
112
A window will appear where you can specify the port to which you can install the
modem.
3. Select "Selected Port", specify the COM port to which the modem will be
installed, and then click on the [Next] button.
Important
.Please specify the COM port displayed in the window pertaining to Step (7)
under "●Setting up the modem station."
113
4. Click on the [Continue] button.
The wizard will display the following window by design, but you may disregard it
and click on the "Continue" button.
A window will appear indicating that the modem installation is complete.
5. Click on the [Finish] button.
6. Confirm that the configured modem has been added to the list in the [Phone
and Modem Options] window, and then click on the [OK] button.
114
The [Next] button will be enabled on the [Add New Connection Wizard (Modem
Settings)] window.
7. Click on the [Next] button on the [Add New Connection Wizard (Modem
Settings)] window.
The [Add New Connection Wizard (Connection Name Settings)] window will
appear.
115
8. Enter the type and name of the icon displayed after registration, and then
click on the [Next] button.
Please click on the [Next] button if you are satisfied with the settings.
The [Add New Connection Wizard (Completing the Add New Connection Wizard)]
window will appear.
9. Click on the [Finish] button.
The settings will be registered, and the icon will appear in the [Bluetooth Settings]
window.
Setting fax information
Configure send/receive settings and register fax information.
1. Select [Start]Æ[Control Panel], and then double-click on the [Printers and
Other Hardware] icon .
Note
.If the control panel is displayed in "Classic view", and you use Windows 2000,
please start from Step (2).
2. Double-click on the [Printers and Faxes] icon.
The [Printers & Faxes] window will appear.
3. Click on "Install a local fax printer" in the [Printers and Faxes] window.
116
A window showing installed programs will appear, and a Fax icon will have been
created in the [Printers and Faxes] screen.
4. Click on "Send a fax" under "Printer Tasks" on the left side of the window.
If you have not yet configured a fax device, the [Fax Configuration Wizard] window
will appear. In the window you can enter settings pertaining to the sender
(yourself).
117
Note
.If the fax configuration information has already been registered, the [Send Fax
Wizard] window, which can be viewed under "Sending a fax" below, will appear
instead of the [Fax Configuration Wizard] window.
5. Enter the sender information, and click on the [Next] button
Note
.The sender information that you configure here will be automatically appended
as header information when you send a fax.
6. Select a device to be used for fax transmissions, enable the device for
sending or receiving, and then click on the [Next] button
118
Note
.If [Enable Receive] is selected, the device will be on standby for receiving faxes
even if it is not sending or receiving anything, and therefore will be in continuous
connection to the wireless modem (when COM Auto Connect is on).
Please decide whether to select this option based on the desired objective and/or
frequency of transmission.
7. Click on the [Next] button.
It is important that you do not change the transmitter subscriber identification.
8. Click on the [Finish] button.
119
Please refer to the same procedure of “Sending a fax” and “receiving a fax” in the “using a
modem station for transmission” section.
4.7 Using a Bluetooth-compatible camera
Connecting the camera
1. Click on [Start ]Æ[All Programs]Æ[Bluetooth]Æ[Remote Camera].
Note
.In Windows 2000, click on [Start]→[Programs]→[Bluetooth]→[Remote
Camera].
The [Remote Camera] window will appear.
2. Turn on the camera, and set it to be connectable via Bluetooth.
Note
.Different cameras are operated in different ways, depending on the
manufacturer and model used. Please refer to the instruction manual for further
details on how to operate your camera.
120
3. Click on the [Camera Search...] button.
The camera will be detected and its icon displayed.
4. Right-click on the camera icon, and select [Connect].
The camera will be connected, and images from the camera will appear on-screen.
121
Taking a signal picture
By placing the mouse cursor over the on-screen image, the camera's operating window
will appear.
You can operate the camera from this window.
1. Click on the
button in the operating window.
A single image will be captured and sent to the PC.
Taking several consecutive frames
122
1. Click on the
button in the operating window.
A succession of images will be captured and sent to the PC.
Note
.The remote camera shutter cannot be operated while the camera is connected
to the PC.
.The number of consecutive pictures taken can be set to anywhere between 2
and 16.
1. In the [Remote Camera] window, click on [Bluetooth]→[Properties]Æ
[Consecutive Image Settings].
2. Click on the [<][>] buttons to select the number of consecutive images
to be captured.
Note
.Images are not only sent to the PC, but are stored in the camera's on-board
memory as well.
Please be aware of the remaining memory capacity when you are taking a large
number of pictures.
.Large file sizes are common for high-resolution images, and may take some
time to be transferred to the PC.
Viewing images saves on your PC
A "Remote Camera" folder will be created in the "Bluetooth" folder under "My Documents"
during initial set-up. A folder bearing the same name as the camera will be created in it,
123
and images will be saved in this folder.
Click the [Explorer] button in the [Remote Camera] window to display the folder where the
images have been saved.
Note
.This window is an example showing pictures when [Filmstrip] has been selected
from the [View] menu in Explorer.
124
4.8 Using a headset to communicate
Registering the headset
1. Right-click on the Bluetooth icon in the tasktray, then click on [Add New
Connection Wizard].
Note
.Alternatively, you can click on [Start]>[All Programs]>[Bluetooth]>[Bluetooth
Settings], then click on [New Connection] in the [Bluetooth Settings] screen that
has opened.
The [Add New Connection Wizard (Welcome to the Add New Connection Wizard)]
screen will appear.
2. Turn the headset power on.
Once you have turned on the headset, set the mode to enable a Bluetooth
connection.
Important
.The procedure for operating the headset may differ depending on the
manufacturer and model.
Please consult your user guide for a detailed description of how to operate the
unit.
3. Confirm that [Express Mode] has been selected, then click on the [Next]
button.
125
The [Add New Connection Wizard (Searching for Bluetooth Devices)] screen will
appear.
Once the device search has been completed, the [Add New Connection Wizard
(Select a Device)] screen will appear.
4. Select the name of the headset device from the list, then click on the [Next]
button.
126
5. Answering with the headset.
If the service has been properly detected, a screen will appear indicating that the
headset is being called, and a tone will accordingly sound in the headset.
Please press the headset switch.
Important
.The procedure for operating the headset may differ depending on the
manufacturer and model.
Please consult your user guide for a detailed description of how to operate the
unit.
The [Add New Connection Wizard (Configuring (Connecting to Voice Circuit))]
screen will appear, and device configuration will be performed.
Note
.If you are connecting to the headset for the first time, or if another Bluetooth
audio device (for example, the TOSHIBA Speech Recognizer) has not yet been
registered, the following [Found New Hardware Wizard] screen will appear, from
127
which you can proceed to install the driver.
If another audio device has already been registered (i.e., the driver has been
installed), you can proceed to Step 9 without having to install the driver.
6. Click on the [Next] button.
The [Install Hardware] screen will appear.
7. Click on the [Continue Anyway] button.
The following screen will appear automatically. You may disregard it and click on
the [Continue Anyway] button.
The [Add New Connection Wizard (Completing the Found New Hardware Wizard)]
screen, which is the final screen of the installation wizard, will appear.
128
8. Click on the [Finish] button.
Once driver installation is complete, the [Add New Connection Wizard (Enter
Connection Name)] will appear.
9. Confirm the information you have entered, and click on the [Next] button.
The [Add New Connection Wizard (Completing the Add New Connection Wizard)]
screen will appear.
129
10. Click on the [Finish] button.
The configuration information will be registered, and an icon will be displayed in the
[Bluetooth Settings] screen.
Making a connecting to the headset
You can make a connection to the headset from an icon that has been registered in
[Bluetooth Settings].
Important
.Before making a connection to the headset, please check that you have turned
on the headset's power, and it has been enabled for a Bluetooth connection.
Please ensure that the following audio-related applications have been closed
before you connect the headset to your PC.
Windows Media Player, BeatJam, InterVideo WinDVD and other
music/audio playback software
o Windows Messenger and other e-conferencing software
o LaLaVoice and other voice-recognition software
o
If you wish to use these applications, please terminate the headset connection
before you launch them.
1. Right-click on the headset icon, then click on [Connect].
130
2. Answer with the headset.
A screen will appear indicating that the headset is being called, and a tone will
accordingly sound in the headset.
Please press the headset switch.
If the connection has been properly established, the icon's appearance will change
to indicate a connected state.
You may now launch conferencing and voice-recognition software and use the headset.
Disconnecting from the headset
Please follow the steps below to disconnect from the headset.
1. Right-click on the headset icon in the [Bluetooth Settings] screen, then click
on [Disconnect].
131
A message will appear, requesting confirmation that you wish to disconnect. Click on
the [Yes] button.
The icon on the [Bluetooth Settings] screen will appear as shown below, indicating that
the device has been disconnected.
132
5
4
Chapter 5
Advanced features
5.1 Making a device undiscoverable to other users
1. Right-click on the Bluetooth icon in the task tray, and then click on
[Options…].
The [Options] window will appear.
2. Tab [Security], then select [Custom Level], enable [Non-discoverable
mode], and then click on the [OK] button.
Your device will now be undetectable by other users, even when they search
for other devices.
Note
.Other devices are still able to establish connections with your device even
if you have enabled the Non-discoverable mode.
Please enable "Non-connectable mode" if you wish to reject connections
from other devices.
133
5.2 Encrypting the content of your transmissions
Since Bluetooth communication is conducted wirelessly, there is always the
possibility that a third party may be able to intercept your transmissions.
You can use encryption to render the content indecipherable to anyone who
manages to intercept it.
Important
.Encrypting your transmissions will still not guarantee complete security.
Accordingly, please be aware that transmitting data is conducted with an
element of risk for the user.
1. Right-click on the Bluetooth icon in the task tray, and then click on
[Options…].
2. Tab the [Custom Level]
3. In the option under the Mode tab, enable [Link level enforced security
[Authentication and encryption] ] then click [OK] to accept it.
Note
.Once you have configured the encryption, a window will appear when you
first make a connection to another device, prompting you to enter a
Bluetooth passkey (PIN code).
Please click on the [OK] button after you have entered the passkey.
134
.The window in which you enter the passkey will not appear once you have
connected more than two times to the device.
5.3 Changing the default connection
The "default connection" refers to the dial-up connection configured for use
whenever a connection is made to the Internet.
If several connections have been registered, you can change the default connection
by following the procedure below.
1. Start Internet Explorer.
2. Click on [Tools]→[Internet Options...].
The [Internet Options] window will appear.
3. Click on the [Connections] tab.
135
In this window, "Direct Connection" is set as the default, and "Never dial a
connection" has been selected.
Change the settings so that "London A" will always be dialled when you
connect to
the Internet.
4. Select "Always dial my default connection".
5. Click on "London A", and then click on the [Set Default] button.
136
"London A" has been changed to the default connection.
5.4 Manually creating a virtual Bluetooth COM port
In order for a PC to connect to and communicate with a Bluetooth device, the
Bluetooth Utility will create a gateway for data to be exchanged between the
respective devices. This gateway is known as a "port" (or "virtual COM port").
137
Since one virtual COM port will be allocated to each device, trouble-free
communication will still be possible even if several devices are being used.
When you use the Bluetooth Utility, a virtual COM port will be automatically created
on set-up; however, virtual COM ports can be created manually if so needed.
5.4.1
Clients and servers
When Bluetooth communications are performed, there will always be a
"client/server" relationship between the various devices. A "client" is a device that
sends certain requests to another device, while a "server" is a device that provides a
service on receipt of such requests from another device.
For example, when a PC issues a print command to a wireless printer, the PC
functions as the client, while the printer functions as the server.
When a PDA or other device attempts to receive files located on a PC by means of
file transfer protocol, the PC functions as the server, while the PDA functions as the
client.
Virtual Bluetooth COM ports can be created both for clients and servers.
•
Bluetooth virtual COM port for a client
Virtual COM port used when your device is the client, and requests are sent
to another device.
•
Bluetooth virtual COM port for a server
Virtual COM port used when your device is the server, and requests are
received from another device.
5.4.2
Creating a virtual COM port
1. Click on the [Printers and Other Hardware] icon in the Control Panel.
138
The [Printers and Other Hardware] window appears.
2. Double-click on the [Bluetooth Local COM] icon.
The main Bluetooth Local COM window will appear.
Note
.Even when the Control Panel appears in Classic view, please simply click
on
the [Bluetooth Local COM] icon.
o
No such distinction between viewing formats exists in Windows 2000.
3. Click on the [Add...] button.
139
The [Bluetooth Local COM Wizard] window, from where you can create a
virtual
COM port, will appear.
Start from this window when creating Bluetooth virtual COM ports for either
servers
or clients.
5.4.3 Deleting a virtual COM port
Note
.You can only delete virtual COM ports created by the Bluetooth Local
COM utility.
1. Select the port you wish to delete from the [Bluetooth Local COM]
window, and then click on the [Delete] button.
140
A message will appear asking you to confirm that you wish to delete the port.
2. Click on the [Yes] button.
The port will be deleted.
3. Click on the [OK] button.
141
6
Chapter 6
Troubleshooting
6.1 General operation of the Bluetooth Utility
Bluetooth Manager
Q: Bluetooth icon does not appear in task tray.
•
If the Bluetooth icon does not appear in the task tray, Bluetooth Manager will
not be active, which will prevent you from being able to use any of the
functions of the Bluetooth Utility.
Start the utilities as instructed below to enable Bluetooth Manager to start
automatically and allow all functions to be utilized.
Bluetooth Settings
(from Windows XP)
[Start] > [All Programs] > [Bluetooth] > [Bluetooth Settings]
(from Windows 2000)
[Start] > [Programs] > [Bluetooth] > [Bluetooth Settings]
Or right click the Bluetooth icon in the system tray , then select “Options…”
Remote Camera
(from Windows XP)
[Start] > [All Programs] > [Bluetooth] > [Remote Camera]
(from Windows 2000)
[Start] > [Programs] > [Bluetooth] > [Remote Camera]
Wireless File Transfer
(from Windows XP)
[Start] > [All Programs] > [Bluetooth] > [Wireless File Transfer]
(from Windows 2000)
[Start] > [Programs] > [Bluetooth] > [Wireless File Transfer]
Q: Unable to turn on Bluetooth.
•
If the wireless communication switch on your PC has been turned off, the
message below will appear, and you will not be able to turn the power on from
Bluetooth Manager.
142
Please confirm whether the wireless communication switch has been turned
on.
Bluetooth Settings
Q: Clicking on the [New Connection] button brings up the message "Unable to
prepare
Bluetooth."
•
The wireless communication switch is turned off.
Please switch it on.
Q: Remote device(s) cannot be detected
•
The other device(s) may have been set to Non-discoverable mode.
Please check the mode settings on the device.
Q: Services on a remote device are undiscoverable
•
The other device may be using a profile that is not supported by the Bluetooth
Utility
Please check the profile being used on the other device.
•
The following profiles are compatible with Bluetooth Settings.
DUN, FAX, LAP, SPP, HID, HCRP, FTP, OPP, HSP, PAN and BIP
Devices running profiles other than those above will not be able to be
registered with Bluetooth Settings
Bluetooth Information Exchanger
Q: Bluetooth Information Exchanger icon does not appear on Desktop
• Bluetooth Information Exchanger is not active. Please follow the procedure
below to start the utility.
1. Right-click on the Bluetooth icon in the task tray
2. Click on [Options…] to open the options for Bluetooth, then
enable [Bluetooth Information Exchanger Service]
143
The Bluetooth Information Exchanger icon will appear on the Desktop.
Q: Transfer failed when sending a file using the right-click menu.
•
FTP or OPP are the sending profiles available when you select a file,
right-click it, and then click on [to Bluetooth] to send it.
If the destination device does not support either of these profiles, you will not
be able to send files using the right-click menu.
File transfer will also be unsuccessful if you use FTP to send a file to a device
that only supports OPP.
In such cases, please click on [Bluetooth] > [Profiles] from [Bluetooth
Information Exchanger], and enter the settings shown under Transfer mode.
Q: Cannot open shared folder on other device with "File Transfer".
•
The other device may have a certain security level enforced
(Non-connectable mode etc). Please confirm the security settings of the other
device.
Please enter the correct password if you are asked to enter one.
144
Remote Camera
•
See "Using a camera"
Bluetooth Local COM
Q: Cannot add port
•
A maximum of 64 virtual COM ports can be added. You will be unable to add
another port if 64 ports have already been configured.
6.2 Using a wireless modem station
Q: Modem station cannot be detected.
•
If the modem station is connected to and is being used by another device, the
modem station will be undetectable even if you search for it.
Q: Cannot connect to modem station
•
If the modem station is connected to and is being used by another device, no
other device will be able to connect to the modem station.
Q: Bluetooth passkey entry failed
•
The Bluetooth passkey (PIN code) comprises a sequence of alphanumeric
characters, with the letters able to be rendered in upper and lower case.
If [Caps Lock] is on, the Bluetooth passkey may not be able to be entered
correctly.
Q: Cannot connect to telephone line
•
Please ensure that the telephone cable is connected from the socket to the
"LINE" terminal on the modem station.
Note
.If the telephone cable has come loose because it has not been fully
inserted into the socket, the resulting poor contact may prevent data from
being transmitted accurately.
.Communication will be impossible if the interior of the cable has been
broken.
Please replace the cable with another one.
•
Please ensure that the two slide switches on the underside of the main unit
have been set to the "NORMAL" and "MODEM" positions respectively.
145
Q: Cannot connect to the Internet
•
The telephone number of the connection (i.e., the telephone number for the
access point of your Internet service provider) may not be correct. Please
check the telephone number.
•
The user ID and/or password for the provider with whom you have signed up
may have been entered incorrectly. Please check the user ID and password.
The default connection may have been configured with different settings.
Please set the connection configured for mobile telephone use as the default
connection.
•
•
When you place a call using a company switchboard or other exchange, the
system may require you to enter a "0" before the telephone number itself.
Please check the type of telephone line you are using.
Q: Cannot send or receive faxes
•
Once you have registered a wireless modem station as your fax server, you
will need to enter the fax settings from the [Printer and Faxes] window in the
Control Panel.
Please refer to "Using a modem station for fax transmissions" for information
on the configuration procedure.
•
The telephone number of the fax destination may have been entered
incorrectly. Please check the telephone number.
•
If the setting under COM Auto Connect Settings has been set to "Off", a
connection will not automatically be established with the modem. Please
connect to the modem manually.
•
When you place a call using a company switchboard or other exchange, the
system may require you to enter a "0" before the telephone number itself.
Please check the type of telephone line you are using.
•
The fax service may not have been enabled for sending (or receiving).
Please check the settings by following the procedure below.
1. Open [Printers and Faxes] from the Control Panel, right-click on
the [Fax] icon, and then click on [Properties].
146
The [Fax properties] window will appear.
2. Select the [Device] tab, right-click on the modem you wish to use,
and then click on [Properties].
3. Select the [Send] tab, and then confirm that "Enable device to
send" has been checked.
147
4. Select the [Receive] tab, and then confirm that "Enable device to
receive" has been checked (when you wish to receive faxes).
5. Click on the [OK] button.
6.3 Using an access point
Q: Access point cannot be detected.
148
•
If the access point is connected to and is being used by another device, the
access point will be undetectable even if you search for it.
Q: Cannot connect to access point.
•
If the access point is connected to and is being used by another device, no
other device will be able to connect to the access point.
Q: Cannot connect to LAN.
•
The LAN cable may not be properly connected to the access point. Please
check the connection status.
Note
.If the LAN cable has come loose because it has not been fully inserted
into the
socket, the resulting poor contact may prevent data from being
transmitted
accurately.
.Communication will be impossible if the interior of the LAN cable has been
broken. Please replace the cable with another one.
•
The access point may not have been configured correctly, and may not be
able to maintain the connection to the LAN.
Please refer to the product instruction manual for information on how to
configure your access point.
Q: Cannot connect to the Internet.
•
If you are using a LAN to connect to the Internet, the LAN environment of the
company or location where you are trying to establish the connection may
require you to connect via a proxy server.
6.4 Using a mobile telephone
Q: Mobile telephone cannot be detected.
•
If the mobile telephone is connected to and is being used by another device,
the mobile telephone will be undetectable even if you search for it.
Q: Cannot connect to mobile telephone.
•
If the mobile telephone is connected to and is being used by another device,
no other device will be able to connect to the mobile telephone.
Q: Cannot send images to mobile telephone.
•
Please use the appropriate transfer method, according to the profiles
supported by your mobile telephone.
If OPP is supported: right-click on a file to send it
149
If BIP is supported: use "Image transfer" under Bluetooth Information
Exchanger to send images
Q: Cannot connect to the Internet.
•
The telephone number of the connection (i.e., the telephone number for the
access point of your Internet service provider) may not be correct. Please
check the telephone number.
•
The user ID and/or password for the provider with whom you have signed up
may have been entered incorrectly. Please check the user ID and password.
•
The default connection may have been configured with different settings.
Please set the connection configured for mobile telephone use as the default
connection.
Q: Cannot send or receive faxes.
•
Once you have registered a mobile telephone as your fax server, you will
need to enter the fax settings from the [Printer and Faxes] window in the
Control Panel.
Please refer to "Using a modem station for fax transmissions" for information
on the configuration procedure.
•
The telephone number of the fax destination may have been entered
incorrectly. Please check the telephone number.
•
If the setting under COM Auto Connect Settings has been set to "Off", a
connection will not automatically be established with the modem. Please
connect to the mobile telephone manually.
•
The fax service may not have been enabled for sending (or receiving).
Please check the settings by following the procedure below.
1. Open [Printers and Faxes] from the Control Panel, right-click on
the [Fax] icon, and then click on [Properties].
The [Fax properties] window will appear.
150
2. Select the [Device] tab, right-click on the modem you wish to use,
and then click on [Properties] .
3. Select the [Send] tab, and then confirm that "Enable device to
send" has been checked.
4. Select the [Receive] tab, and then confirm that "Enable device to
receive" has been checked when you wish to receive faxes).
151
5. Click on the [OK] button.
6.5 Using a PDA
Q: Cannot make an ActiveSync connection.
•
Please confirm that you have installed ActiveSync v3.7 or higher on your PC.
•
ActiveSync is installed to COM7 as a default. Please refer to "Synchronizing
data with a PDA" and re-configure your ActiveSync connection.
If a port other than COM7 has been used, please amend the ActiveSync
connection settings accordingly.
Q: Cannot locate a saved file.
•
The type of file sent to your PDA, as well as the profile used to send the file,
may affect where folders saved on your PDA are located.
Examples:
Images transferred to your PDA using "Image transfer" > saved in the "Image
transfer" folder
Images transferred to your PDA using "File transfer" > saved in the "Shared
folder"
152
6.6 Using a camera
Q: Camera cannot be detected.
•
If the camera is connected to and is being used by another device, the
camera will be undetectable even if you search for it.
Q: Cannot connect to camera.
•
If the camera is connected to and is being used by another device, no other
device will be able to connect to the camera.
Q: Images from the camera can be displayed, but no pictures can be taken.
•
The memory card in the camera may be full.
Please make a backup of all your necessary data on alternative media, then
delete the images from the memory card, and ascertain how much free space
remains.
Q: Camera images do not appear in window.
•
The camera may not have been set to remote camera mode (image browse
mode, configuration mode, etc).
Certain cameras will end the Bluetooth connection automatically if you
change the settings in a mode other than remote camera mode. Please
re-connect to the camera when you next wish to use the device in remote
camera mode.
6.7 Using a Bluetooth Headset
Q: Bluetooth Headset cannot be detected.
•
If the Bluetooth Headset is connected to and is being used by another device,
the Bluetooth Headset will be undetectable even if you search for it.
Q: Cannot connect to Bluetooth Headset.
•
•
If the Bluetooth Headset is connected to and is being used by another device,
no other device will be able to connect to the Bluetooth Headset.
A Bluetooth connection will be impossible if the Bluetooth Headset is
connected to a power adaptor.
Please remove the power adaptor and re-connect.
Q: Sound cuts out/cannot hear anything.
•
Using a Bluetooth headset with other Bluetooth devices may cause problems
such as interruptions in sound, reduced transfer speed or failure during file
transfer, and disconnection of the other Bluetooth devices. We strongly
153
recommend using a Bluetooth headset on its own and not in connection with
other Bluetooth devices.
•
Please confirm that the Bluetooth Headset is being operated correctly (for
example, ensure that the correct mode (audio or communications) mode has
been selected).
•
Please confirm that the voice file or CD is being played back normally on your
PC.
•
Please check the volume settings on your Bluetooth Headset and PC.
•
If Windows Media Player or another audio-related application is active when
you try to connect your Bluetooth Headset, you may find it impossible to
connect properly to the Bluetooth Headset, or even to use it at all.
Please start such applications after you have connected to the Bluetooth
Headset.
154
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This device is intended only for OEM integrators under the following
conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna. As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is
no longer considered valid and the FCC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the
end product (including the transmitter) and obtaining a separate FCC authorization.
155
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising