Manual - Audio General Inc.
RemotePoint
Jade
User’s Manual
®
VP4910
LASER Safety Statement
CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure.
The laser is activated by pressing laser button identified in the
user guide.
Do not stare into laser beam.
Do not shine a laser pointer at anyone.
Do not allow minors to use laser pointer unsupervised.
Do not point laser pointer at any reflective surface. A reflected beam can be the same as a direct beam.
Do not disassemble the device.
Do not immerse in any liquid or expose to heat or moisture.
Use only within the designed operating temperature range of
0-40 deg C.
This product has no serviceable parts.
Laser Specifications:
The laser used in the VP4910 complies as Class 2 laser product
with: IEC/EN 60825-1: 1994+A1+A2, and CFR Title 21 1040.10 and
1040.11, except for deviations pursuant to Laser Notice No.50,
dated June 24, 2007.
First Use
1.
Open the battery compartment by pressing down on the latch. Insert the batteries
per the diagram on the remote. Standard AA alkaline batteries are recommended.
2.
With the computer turned on, plug the receiver into a
free USB port. (If the computer displays a “Found New
Hardware” dialog box, click Next until the driver is
installed.)
Pairing the Receiver
The receiver and remote come pre-paired at the factory. The remote will
automatically adjust frequencies and channels to ensure reliable
communication. Should you have any problem with
communication, you can re-pair them by plugging
the USB receiver into the AutoRF Port on
the back of the remote.
Jade Controls
Mouse Control
Activate Laser
Previous Slide
Right Click
Next Slide
Left Click
(Trigger)
Customizable
Buttons
RemotePoint Jade
Model VP4910
Laser Specification:
Max output power: <1mW.
Emitted wavelength: 522-542nm
The Class 2 laser beam is emitted from the front of the device,
indicated by the aperture warning label.
Auto RF Port
Customizing Buttons
The four buttons on the bottom of the VP4910 can be programmed to send a wide
variety of keystrokes. The software is available online at
http://www.smklink.com/support/downloads.html
The remote can also be programmed
to meet your own needs. To change
the functions of the remote, select
individual keys from the drop down
menu. Once you have made your
selection click “Program Receiver.”
Once programmed, the changes are
written to non-volatile memory on the
receiver.
The Customizing software requires Windows to run or a Mac, running Boot Camp. Once
programmed those buttons will send those keys even on machines that aren’t running
the setup utility software, including Mac, Windows and Linux machines.
Warranty
SMK-Link Electronics Corporation (SMK-Link) warrants to the original end-user
purchaser of the Product (“you”) that the Product, excluding batteries, will be
free from defects in materials and workmanship under normal use and service
for one-year from date of purchase. If the product becomes defective in materials or workmanship during the warranty period, SMK-Link will, at its option,
either repair or replace it. The replacement unit may be a more current or
upgraded model if the originally purchased model is not available. Any Product
repaired or replaced under the terms of the warranty is covered for the remainder of the original warranty period or ninety (90) days from the date of return
shipment, whichever is longer. This warranty does not cover products which
have been subjected to misuse, accident, physical damage, improper installation,
abnormal operation or handling, neglect, inundation or fire or when product
regulator label has been removed, altered or rendered illegible; nor does it cover
accessory or consumable items.
SMK-Link shall not be liable for any indirect special, incidental, or consequential
damages. SMK-Link’s total liability for damages for any cause related to, or arising
out of, the use or inability to use the product shall not exceed the original price
paid for the product even if SMK-Link has been informed of such possibility.
If your product requires service under warranty, you must first contact SMK-Link
product support to receive an RMA number. Shipping of defective units back to
SMK-Link is at your expense. The contact information can be found on the SMKLink website: www.smklink.com.
This warranty does not affect your statutory rights and you may have other
rights which vary from state to state and country to country. This warranty is
understood to be the complete and exclusive agreement between the parties,
superseding all prior agreements, oral or written, and all other communications
between the parties relating to the matter of this warranty.
The above warranty does not apply to products sold in Australia. Products sold
in Australia by an authorized reseller will contain an Australia specific warranty
statement.
FCC Certification
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a CLASS B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a residential installation. This equipment generates, uses, can radiate radio frequency
energy and if not installed and used in accordance with the instruction guide, may cause
harmful interference to radio communications. However, there is no guarantee that this
radio interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment on and off, the user is encouraged to try to correct the interference by one
or more of the following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced Radio-TV technician for help.
Notice: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. Extension cables are
not recommended, if used, they must be shielded in order to comply with the emission
limits.
IC Certification
The term “IC” before the certification/registration number only signifies that the Industry
Canada technical specifications were met.
Declaration of conformity
Manufacturer: SMK-Link Electronics Corporation
3601-B Calle Tecate
Camarillo, CA 93012
Hereby, SMK-Link declares that the VP4910 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
EMC/EMI/Safety Standards:
EN 300 440-2 V1.1.1 (2001-09)
EN 301 489-1 V1.4.1 (2002-08)
EN 301 489-3 V1.4.1 (2002-08)
EN 60825-1 (1994, A11:1996, A2:2001)
Thank You
Thank you for purchasing a RemotePoint Jade. We know
you had other choices and we appreciate that you chose
SMK-Link for your wireless needs. So that we may better
serve you in the future, please register online at
www.smklink.com/register.
Support
SMK-Link Electronics Corporation
3601-B Calle Tecate
Camarillo, CA 93012
TEL: (888) 696-3500
FAX: (805) 987-6665
Email: pcsupport@smkusa.com
www.smklink.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising